Upload
realacoustix-llc
View
221
Download
0
Embed Size (px)
DESCRIPTION
Â
Citation preview
NWAA Labs 25132 Rye Canyon Loop, Santa Clarita, CA 91355, Phone:(253) 973-1018
Email address…[email protected] SOUND ABSORPTION
TEST REPORT No. NW072109-1 Client: RealAcoustix, LLC 903 N Marshall Way Layton, UT 84041 Test Date: 21 July 2009 Test Specimen: RealAcoustix DSA Panels (Type “A” Mounting) INTRODUCTION The methods and procedures used in this test conform to the provisions and requirements of ASTM Procedure C 423-02a, Standard Test Method for Sound Absorption Coefficients by the Reverberation Room Method. Copies of the test standard are available at www.astm.org. The test chamber is a cuboid, 871.7cm long by 541cm wide by 609.6cm high, and volume is 275 cubic meters. There are six fixed surfaces and two movable/fixed surfaces oriented as diffusors in the reverberation room. There are two sources one in each corner consisting of two Dodecahedron speakers and two sub-bass cabinets for extended low frequency capabilities. This test report relates only to the item(s) tested. Any advertisement that utilizes this test report or test data must not imply product certification or endorsement by NWAA Labs. DESCRIPTION OF TEST SPECIMEN The test specimen consisted of RealAcoustix DSA (Diffractive Slot Absorber) panels. The test specimen consisted of two 96 inch (2.44 m) by 48 inch (1.22 m) by 3/4 inch (19 min) panels and one 96 inch (2.44 m) by 12 inch (305 mm) by 3/4 inch (19 min) panel. The panels were laid side by side on the test chamber floor to form a nominal 9 foot (2.74 m) by 8 foot (2.44 m) sample. For the test, 1 inch (25.4 mm) thick 6 Ib. density fiberglass was located in the specimen below the test panels. Edge pieces were attached to the panels covering the fiberglass around the entire perimeter. The specimen was taped to the test chamber floor around the entire perimeter. The test surface consisted of 1/8 inch (3.2 mm) wide, 1/8 inch (3.2 mm) deep slots on 1 inch (25.4 mm) centers. The overall dimensions of the specimen were 108 inches (2.74 m) by 96 inches (2.44 m) by 1-3/4 inch (44 mm) thick. The overall weight of the specimen was 197 Ibs. (89.4 kg). Test results are on the following pages. Submitted by, NWAA Labs Inc ___________________________ Ron Sauro NWAA Labs Inc
Test Date: 25-May-2007
Mounting per ASTM E795-00: Type AArea Tested: 71.44 Ft² (6.64m²)Temperature: 72.4°FHumidity: 48%
Test Results:
NWAA Labs25132 Rye Canyon LoopSanta Clarita, CA 91355
(253)-973-1018
RealAcoustix DSA Panels (Type "A" Mounting)
0.00
0.10
0.20
0.30
0.40
0.50
0.60
0.70
0.80
0.90
1.00
1.10
1.20
1.30
100H
z
125H
z
160H
z
200H
z
250H
z
315H
z
400H
z
500H
z
630H
z
800H
z
1000
Hz
1250
Hz
1600
Hz
2000
Hz
2500
Hz
3150
Hz
4000
Hz
5000
Hz
6300
Hz
8000
Hz
1000
0Hz
Frequency [Hz]
Ab
sorp
tio
n &
Sc
atte
rin
g C
oef
fici
ents
Absorption Coeff
FrequencyAbsorptionCoefficient
Absorptionin Sabines
100Hz 0.13 9.30125Hz 0.08 5.60160Hz 0.19 13.60200Hz 0.27 19.80250Hz 0.52 37.60315Hz 0.87 62.50400Hz 1.13 81.60 NRC 0.65500Hz 1.19 86.00630Hz 0.98 70.80 SAA 0.64800Hz 0.77 55.60
1000Hz 0.58 41.501250Hz 0.43 31.301600Hz 0.35 25.202000Hz 0.29 21.002500Hz 0.27 19.203150Hz 0.24 17.004000Hz 0.25 17.905000Hz 0.20 14.706300Hz 0.21 14.908000Hz 0.24 17.20
10000Hz 0.28 20.40
Test Results
RealAcoustix DSA Panels (Type "A" Mounting)
NWAA Labs25132 Rye Canyon LoopSanta Clarita, CA 91355
(253)-973-1018
Type A71.44 Ft² (6.64m²)
72.4°F48%
25-May-2007
Humidity:
Test Date:
Mounting per ASTM E795-00:Area Tested:Temperature: