57

WWW.PSI-PRODUCTS.COM

OD 32-315 UP TO 5 BAR TESTED AND FROM OD 355 UP TO 4 BAR

GROUND AND PRESSURE WATER TIGHT

PIPE, CABLE AND LIGHTNING PROTECTION

PSI WALL COLLAR

58

PSI Wall Collar

GENERAL INFORMATION

Note: The PSI wall collar is not an anchoring point for pipes.

Application examples

Swimming pool Man hole opening

An economical and reliable method of hydrostatic sealing

PSI wall collars are used for the hydrostatic sealing of pipes made of steel, cast iron, copper, plastic, fi ber reinforced concrete, concrete and vitrifi ed clay that pass through walls, ceilings, fl oors, shaft openings, swimming pools and groundwater tanks.

PSI wall collars are the ideal solution wherever it is not possible to retrofi t wall sleeves or drill holes.

• Groundwater and pressing water tight• For pipe OD 32 to OD 315 tested up to 5 bar• From pipe OD 355 tested up to 4 bar

Material high quality rubber Value/unit

Tensile strength 9,5 N/mm2

Elongation at break 500%

Shore hardness A 45 ± 5°

Service temperature max. 80 °C

Minimum temperature - 40 °C

More content can be found on www.psi-products.com

59

PSI Wall Collar round & flat

GENERAL INFORMATION

Round conductor 8 - 10 mmFlat conductor 30 x 3,5 or 3 mm

For sealing pipes, cables and lightning protection wires in wall-openings, ceilings, fl oors, shaft entries, swimming pools and groundwater tanks, the wall collars are the best accessory for a hydrostatic sealing of the penetration.

ADVANTAGES

• Water pressure tight• High quality rubber• Fast and easy installation

Material high-quality rubber Value/unit

Tensile strengh 9,5 N/mm2

Breaking elongation 500%

Shore hardness A 45 ± 5°

Operating temp. max. 80 °C

Operating temp. min. - 40 °C

60

PSI Wall Collar

DIMENSIONS AND INSTALLATION INSTRUCTIONS

Outer diameter of pipe in mm

Clamping range from outer diameter to outer diameter of pipe of pipe

10 8 1030 x 3,5 mm flat - -

32 29 3240 38 4250 48 5363 60 6475 71 8090 84 92110 105 116125 120 130140 135 148160 154 166180 175 190200 195 210225 215 230250 245 260280 275 290315 310 327355 350 365400 395 410450 440 460500 495 515560 555 580630 625 650710 705 735800 795 830900 895 9301000 995 10301200 1195 12401400 1395 1450

Dimensions in mm (without warranty)

INSTALLATION INSTRUCTIONS

1. Clean the pipe surface to be cast in concrete with a piece of cloth or something similar.

2. Slide the wall collar on the pipe to the middle of the concrete/masonry.

3. Attach the fastening straps: For wall collar up to Ø 315: Fit one strap on each side of the fl ange For wall collar above Ø 355: Fit one strap on each side of the fl anges and one in between.

4. Put the fastening strap around the wall collar and insert the end of the strap into the slot of the turnbuckle.

5. Use a bolt driver or hexagon wrench to turn the turnbuckle to the right and then slightly press the locking device until it fi ts tightly.

PSI Products GmbHUlrichstrasse 2572116 Mössingen / Germany

Phone: 0 049 (0)7473 3781 0Fax: 0 049 (0)7473 3781 35E-Mail: export@psi-products.de

www.psi-products.com© PSI Products GmbH, 08 I 2019