ProX® SLS 61003D Printer

FiltersRemoval & Replacement

Purpose:

To provide a step by step instructions for removing and replacing the ProX SLS 6100 Filters.

Performed by:

Customers

Tools and Equipment Required:

• T-20 Torx Driver• Vacuum cleaner

Filter Part Numbers

Part Number Description Quantity

532855 Carbon Filter 1

106029-00 EPM Filter 1

106035-00 Filter, 2-stage, 5 microns 1

76-0313 IPM Laser Filter 2

* 76-0502 IPM Air Filter 1

76-0093 E-Box Filter 1

** 76-1687 IPM Blower Filter 1

* Not needed if the IPM Cooling upgrade has been installed

** Only required if the IPM Cooling Upgrade has been installed

2

3

1. Close Windows by selecting Start then Shutdown. Wait until Windows has completely shutdown before proceeding to the next step.

2. On the back of the printer, turn off the main power supply by rotating the handle counterclockwise.

The adjacent diagram shows the location, names, and part #’s for the ProX SLS 6100 filters.

D

AB

F

E

C

Part Number Description Qty.

A 532855 Carbon Filter 1

B 106029-00 EPM Filter 1

C 106035-00 Filter, 2-stage, 5 microns 1

D 76-0313 IPM Laser Filter 2

* E 76-0502 IPM Air Filter 1

F 76-0093 E-Box Filter 1

** G 76-1687 IPM Blower Filter 1* Not needed if the IPM Cooling upgrade has been installed

** Only required if the IPM Cooling Upgrade has been installed

G

4

Carbon and EPM Filter (Needs to be checked weekly)1. On the back of the printer, open the double

doors.

2. Remove the filter cover by loosening the (4) thumbscrews. Place cover to the side.

5

Carbon and EPM Filter (Needs to be checked weekly)

3. Vacuum all material that may be present.

4. The Carbon and EPM filters will need to be replaced if there is significant amount of material build up.

Carbon Filter

EPM Filter

6

E-Box Filter (Needs to be checked weekly)

1. On the back of the printer lift the E-Box filter housing straight up.

2. The E-Box filter will need to be replaced if there is significant amount of material build up.

IPM Laser and Air Filter (Needs to be checked weekly )

1. On top of the printer, remove the (4) screws from the laser panel using a T-20 Torx driver. Place panel to the side.

2. Loosen the (4) thumbscrews from the laser cover. Place cover to the side.

IPM Laser Filter

IPM Air Filter

7

IPM Laser and Air Filter (Needs to be checked weekly )

3. There are (2) IPM Laser filters. Pull the pins to release the filter housing. Lift filter straight up.

4. The IPM Laser filters will need to be replaced if there is significant amount of material build up.

8

IPM Laser and Air Filter (Needs to be checked weekly )5. Loosen the (2) thumbscrews from the IPM Air Filter housing.

6. Lift the housing straight up access the IPM Air Filter. The IPM Air Filter will need to be replaced if there is significant amount of material build up.

9

Sock Filter (Needs to be checked weekly )1. From the left side of the printer,

open the access panel. Loosen the (2) thumbscrews from the sock filter housing.

2. S lide the sock filter out. Material can be recycled back into the sifter on the MQC. If disposing of DuraForm ProX materials, follow any local ordinances and the guidelines found in the Safety Data Sheet (SDS). The sock filter will need to be replaced if the air flow has become compromised even after the material has been emptied.

10

IPM Blower Filter (Needs to be checked weekly )Note: This filter is only required if the IPM Cooling Upgrade has been installed.

1. Loosen and remove the (4) thumbscrews from the IPM blower filter cover.

2. Remove cover

3. The IPM Blower Filter will need to be replaced if there is significant amount of material build up.

Note: Confirm filter is positioned in the correct air flow direction.

11

Air flow

3D Systems, Inc. 333 Three D Systems Circle Rock Hill, SC 29730www.3dsystems.com2020 Copyright © 3D Systems, Inc. All rights reserved. p/n 76-D047 Rev_B