Productivity Inc®

Haas ST-30/ST-30SS PRE-INSTALLATION CHECKLIST – Rev 11/2010

Installation of your new Haas ST-30/ST-30SS can be smooth and rapid if preparations are made prior to the delivery of your machine. Any questions regarding machine installation should be directed to our service department for clarification. We hope this checklist will aid in a rapid installation of your new machine. NOTE: The following must be completed prior to our service technician arriving to install your new machine.

Power Requirements for your machine: 230v/3ph/28kVa 100 amps (*460v/3ph/28kVa, 50 Amps) NOTE: If BB option is ordered, use 28kVa, 100 Amps (230v) or 50 Amps (460v) Proper voltage per machine specifications should be ready at machine site. Do NOT power up machine. A separate earth ground wire of the same conductor size as the input power must be connected to the chassis of the machine; must be supplied from the main plant ground. A local cold-water pipe or ground rod is not sufficient. *460v requires an External Transformer.

NOTE REGARDING 1000 PSI High Pressure Coolant - You will need a separate power source. 208-230v/3ph/20 Amp circuit needed for the unit. The CNC does NOT provide the power source. Any questions, please contact our service department.

Customer should furnish/have available the proper supply/types of lubricants required for machine operation.

ITEM CAPACITY FLUID TYPE Coolant 55 gallons Water Soluble, synthetic Way Lube 80 oz Mobil Vactra #2

You will need to have Coolant and lubricants on hand at the time of installation. Contact our Service Department for more information.

Air lines should be routed to the machine location and operational for proper air pressure. The Lathe requires a minimum of 100 PSI at 4 cfm at the input to the pressure regulator on the back of the machine. This should be supplied by at least a 1-HP compressor, with a minimum 20-gal tank, that turns on when the pressure drops to 100 PSI. The air must be supplied through a minimum 3/8” hose and fittings must be at least ¼” NPT.

Machine location should be planned to allow enough room for access panels to be opened and serviced with ease. A

minimum of 36” around the machine is required for operator and maintenance access.

Weight requirements should be checked to insure that the surface below the machine will have sufficient strength for support and stability. The machine must be set on a solid, sound and stable, steel bar-reinforced concrete slab poured directly on the grade. In general, the 6” concrete floor on industrial buildings is suitable for machine placement.

NOTE: THE HAAS LATHE CANNOT BE CRANED WITHOUT PURCHASING THE LIFTING KIT, INSTALLED AT THE FACTORY AT TIME OF MANUFACTURE, OR IT MUST BE LIFTED WITH FORKLIFT. CONTACT YOUR SALESPERSON OR LOCAL SERVICE DEPARTMENT FOR MORE INFORMATION. Upon arrival of your machine, unpack and immediately check for visible damage.

SHIPPING WEIGHT SHIPPING DIMENSIONS OF MACHINE 13,660 # (ST-30) 2,085 # (Barfeeder) (Optional Chip Conveyor)

14’6” L x 7’5” W x 7’11” H* (Machine skidded/packed – ST-30, *ST-30SS 7’5” H) 8’6” L x 6’ W x 7’ H (Opt Bar feeder skidded/packed) (Optional Belt-Style Chip Conveyor shipped attached to machine)

See attached for Operational Dimensions/Floor Space Requirements.

Remove as much preservative from the machine as possible without having to power up (tables – slides, pulleys, etc.). We recommend mineral spirits to clean. Apply oil when finished to prevent rust.

15150 – 25th Avenue North, Minneapolis, MN 55447-1981 Phone 763-476-8600 Fax 763-476-4092 Visit us at: www.productivity.com

Service Dept: (MN) 763-476-4191 (IA) 319-632-4288 (NE) 402-330-2323 Productivity is ISO 9001:2000 Certified

ST-30/ST-30SS Dimensions/Layout

Front View:

Top View:

* With optional two-speed gearbox, add 6" (152 mm).

Optional Servo Bar Footprint:

36-3/4”(933.5 mm)

70” (1778 mm)

49”(1244.6 mm)

76-1/8”(1933.2 mm)

127-1/4”(3232 mm)

Max.

164-19/32” (4180.7 mm) SS-30 without Gearbox

DoorOpen

55 Gallon (208.2 L) Coolant Tank78” (1981 mm) x 27.5” (699 mm)

175-19/32” (4460 mm) ST-30 with Gearbox

175-19/32” (4460 mm)

118-1/4” (3003.6 mm) Min.

92”(2336.8 mm)

76-1/8”(1933.2 mm)

115-15/16”(2945 mm)

83-5/32”(2112 mm)

115-15/16”(2945 mm)

69-27/32” (1773.9 mm) Min.

Front

Base Casting

23-45/64”(602 mm)

Φ32.0”(812.8 mm)

Φ32.0”(812.8 mm)

Φ32.0”(812.8 mm)

Φ32.0”(812.8 mm)

Φ32.05”(814.1 mm)Over front apron

Φ24.47”(621.5 mm)Over Tailstockframe

Φ20.94”(531.9 mm)Over Cross Slide

ST-30 Tool Envelopes

ST-30 Tool Envelope VB24

ST-30 Tool Envelope VB12

ST-30 Tool Envelope VDI

ST-30 Tool Envelope BOT

5.60” (142.2 mm)4.69”

(119.1 mm)

6.0” (152.4 mm)

23.20”(589.3 mm)

18.25”(463.6 mm)

7.97” (202.4 mm)

4.80”(121.9 mm)

7.81”(198.4 mm)

10.72”(272.3 mm)

21.45”(544.8 mm)

15.63”(396.9 mm)

15.63”(396.9 mm) 6.53”

(165.7 mm)

8.19”(207.9 mm)

8.19”(207.9 mm)

4.04”(102.7 mm)

18.56”(471.4 mm) BOT ID

VB24 BOT ID

VB12 BOT ID VB24 VDI IDBOT OD

VB12 OD

VDI OD,

26.0” (660.4 mm)

26.0” (660.4 mm) 26.0” (660.4 mm)26.0” (660.4 mm)

26.0” (660.4 mm)

26.0” (660.4 mm)

26.0” (660.4 mm)

26.0” (660.4 mm)

26.0” (660.4 mm) 26.0” (660.4 mm)

26.0” (660.4 mm)

10.60”(269.1 mm)

9.15” (232.4 mm)

12.50” (317.5 mm)

12.50” (317.5 mm) 12.50” (317.5 mm)12.50” (317.5 mm)

12.50” (317.5 mm)

12.50” (317.5 mm)

12.50” (317.5 mm)

12.50” (317.5 mm)

12.50” (317.5 mm) 12.50” (317.5 mm)

12.50” (317.5 mm)

9.17”(232.9 mm)

8.01” (203.5 mm)

12.12”(307.9 mm)

10.81”(274.6 mm) 12.12”

(274.6 mm)

7.83” (198.9 mm)

VB12 VDI OD

VDI ID, VB12 VDI ID

VB12 LTVB24 LT

VB24 VDI ODVB24 BOT OD

4.50”(114.3 mm)

4.50”(114.3 mm)

6.75”(171.5 mm)

8.00”(203.2 mm)

8.34”(211.7 mm)

9.21”(233.9 mm)

10.81”(274.6 mm)

A

A

.70”(17.8 mm)

.25”(6.4 mm).22” (5.6 mm)

.22” (5.6 mm) 2.18” (55.4 mm) 2.06” (52.3 mm)

2.06” (52.3 mm)

View A-A ST-30 Cut Envelope Diagrams

156-25/32” (3982.2 mm) Shipping Position

33.26” (844.8 mm)

26.0” (660.4 mm)

10.66”(270.7 mm)

12.50” (317.5 mm)

41.64” (1057.6 mm)

1.29” (32.8 mm)

28.50” (723.9 mm)

.25” (6.4 mm)

40.35” (1024.9 mm)

30.0” (762 mm)

Drawing Name: ST-30 2010_Machine Views.cdrNetwork Path: I:\Graphics\ST-30Last Updated: 01/11/10Drawn By: G. Grajeda Change Description: First Release