Embed Size (px)
Citation preview
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
TLC range TLC-FW1, TLC-ST1Fullwood range FW38U, FW68U, FW69U
Manus range MS031U, MS197U, MS897U, MS163UGascone Melotte range GM22U, GM99U
Suitable for following claws
Westfalia range Magnum 450Fullwood range FreewayInterPuls range Orbiter, Lunik
Manus range OptimumGascone Melotte range Isolac
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp10u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
Orion range O23U
Sutable for following claws
Westfalia range Magnum 450InterPuls range Orbiter, LunikFullwood range FreewayStrangko range Strangko claws
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp10u-01-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
SAC range SAC012U, SAC010U, SAC020U, SAC022U
Sutable for following claws
SAC range UnifolwInterPuls range Orbiter, Lunik, Galaxy (15 mm nipple)Fullwood range Eva
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp11u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
Gascone Melotte range GM16U, GM2U, GM74U, GM75UFullwood range FW14U, FW27U, FW37U, FW46U, FW67U
DeLaval range DL000U, DL001U, DL016U, DL017U, DL017U-01, DL178U, DL179U, DL295U
SAC range SAC007UDairy Master range DM916U
Manus range MS123U, MS390U
Sutable for following claws
DeLaval range Hydropuls 8 mm, HCC 150 8 mm, HCC 150 9,5 mm; MC 31 10 mm; SAC Innenstutzen 8 mm
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp12u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
TLC Range TLC-A3, TLC-A5, TLC-A6
DeLaval range DL009U, Dl007U, DL007U-01, DL008U, DL4007U, AL6U, DL036U, DL37U, DL037U-01
Sutable for following claws
DeLaval range TF 350/360, ATF 450, MC 93Fullwood range Eva
SAC range UniflawInterPuls range Orbiter, Lunik, Galaxy (15 mm nipple)
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp13u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
TLC Range TLC-W2
Westfalia range WS10U, WS120U, WS150U, WS220U, WS230U, WS270U-01, WS3-100U, WS3-110U
Fullwood range FW22U,MEL range MEL278U, MEL450U
Sutable for following claws
Westfalia range Classic 330 clFit on every cluster with appropriate short milk tube with sight glass
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp14u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
TLC Range TLC-BX1, Manus range MS390U, MS507U,
Boumatic range BM1XU, BMFMU, BMEXUWestfalia range WS025U, WS029U, WS240U, WS27U
DeLaval range DL295U-10
Gascone Melotte range GM85U, GM86U, GM88U, GM89U, GM91U, GM93U, GM95U
Sutable for following claws
Boumatic range Flo MAX Star, Flo StarWestfalia range Classic 330 cl
DeLaval range HCC 150 9,5 mm, MC 31 10 mmInterPuls range Lunik, Orbiter
Gascone Melotte range Isolac (claw angled nipple)Germania range Germania clawsFullwood range Freeway
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp15u-aIr - triangular Liners & Shells
• Minimum pipe diameter Milk: minimum 50 mm, from 6 clusters: 60 mm, from 12 clusters: 76 mm
• Installation must be inspected each year and an advi-sory measure and report must be available.
• Installation must conform to ISO standards• Suitable for medium-and small teats• Suitable for high yielding dairy cows with quick-release:
average milk speed from 2.5 kg / min and above• Uniform Building udder and teat implantation• Aeration in the jaw to close. (Glue, sticker, wall plugs)• Good and hygienic milking routine is very important
• Milkmeter should regularly check the air holes• When stainless steel / plastic rings
plastic rings• By default, IP-MV needs no additional weight• All lightweight claws• For very fast milking cows
stainless steel rings• When milking cows tougher• Replacement of wash cups
Recommended Set-up by Milk-Rite
High line Mid line & robots Low lineMachine vacuum 48 kPa 45 kPa 42 kPa
Pulsation ratio 60:40 60:40 60:40B-Phase range 400 - 450 ms 400 - 450 ms 400 - 450 msD-Phase range 250 - 280 ms 250 - 280 ms 250 - 280 msPulsation rate 60 bpm 60 bpm 60 bpm
Recommended air consumption by Milk-Rite
Per cluster Per linerAir consumption during washing 7,5 l / min 30 > 48 l / min
Air consumption during milking in simultaneous pulsation 4 > 5,5 l / min 16 > 20 l / minAir consumption during milking pulsating alternating 4 > 5,5 l / min 8 > 11 l / min
Recommended B-Phase to use maximum milking speed
Claw Vacuum B-phase (ms)kPa “Hg 300 350 400 450 500 550 60034 10.0 65% 70% 74% 77% 80% 81% 81%36 10.5 68% 73% 77% 80% 81% 82% 82%37 11.0 71% 75% 79% 82% 84% 84% 84%39 11.5 74% 78% 82% 84% 86% 86% 86%41 12.0 77% 82% 85% 87% 88% 88% 88%42 12.5 81% 85% 88% 90% 91% 91% 90%44 13.0 85% 89% 91% 93% 94% 93% 92%46 13.5 89% 93% 95% 96% 97% 96% 94%47 14.0 93% 97% 99% 100% 100% 99% 97%
Milking Speed (% of MAXIMUM) - not using IP liners maximum benefits; - maximum speed, but concrete some teat end problems; - maximum speed and very good teat end condition
Replacement For
TLC Range TLC-BX1, Manus range MS390U, MS507U,
Boumatic range BM1XU, BMFMU, BMEXUWestfalia range WS025U, WS029U, WS240U, WS27U
DeLaval range DL295U-10
Gascone Melotte range GM85U, GM86U, GM88U, GM89U, GM91U, GM93U, GM95U
Sutable for following claws
Boumatic range Flo MAX Star, Flo StarWestfalia range Classic 330 cl
DeLaval range HCC 150 9,5 mm, MC 31 10 mmInterPuls range Lunik, Orbiter
Gascone Melotte range Isolac (claw angled nipple)Germania range Germania clawsFullwood range Freeway
TRIANGULAR MOUTHPIECE VENTED LINERSproduct rangeIp4LM-aIr - triangular Liners & Shells
