Upload
others
View
13
Download
0
Embed Size (px)
Citation preview
PRIMERGY RX900 S1System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 0 System software
1 I Basic unit
2 II Processor
3 III Memory
4 IV USB devices / optical devices
5 V Hard disk drives
6 VI Tape Devices
7 VII Internal SAS RAID Controller
8 VIII External SCSI / SAS controller
9 IX Fibre Channel controller
10 X Communication / Network
11 XI iRMC S2 advanced pack / TPM
12 XII Optional PSU / Power Cord
Change report
PRIMERGY Server
January 2012
System configurator and order-information guidePRIMERGY RX900 S1 Status 2011-12-30
Instructions
This document contains basic product and configuration information that will enable you to configure your system viaPC-/System-Architect
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom.
Section III Memory, example
There are X memory slots which can be equipped with XXX MB
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
Further information in the internet see:
http://ts.fujitsu.com/products/standard_servers/index.html (internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx(extranet)
Prices and availability see price list and PC-/System-Architect.Subject to change and errors excepted.
Fujitsu Technology Solutions PRIMERGY Server 2 of 17
System configurator and order-information guidePRIMERGY RX900 S1 Status 2011-12-30
Configuration diagram PRIMERGY RX900 S1
Basic Unit ( I )Processor ( II )
Memory ( III )
Ether 2 Ether 4 Ether 6
Service Ether 1 Ether 3 Ether 5
1. PSU 2. PSU 4. PSU ( 2+2 )
Hot Plug Redundant Power Supply (XII)
Option
Slo
t #8 P
CIe
2.0
x8,
inte
rnal R
AID
Vid
eo
Slot #1 PCIe 2.0 x8, short length
Included in the base configuration
Slo
t #13 P
CIe
2.0
x8,
short
lengh
Slo
t #12 P
CIe
2.0
x8,
short
lengh P
HP
CO
M
Slot #2 PCIe 2.0 x8, short length
RE
AR
VIE
W
US
B #
1
US
B #
2
3. PSU ( 2+1 )
US
B #
4
Slo
t #11 P
CIe
2.0
x8,
short
lengh P
HP
Slo
t #10 P
CIe
2.0
x8,
short
lengh P
HP
Slo
t #9 P
CIe
2.0
x8,
short
lengh P
HP
Slo
t #17 P
CIe
2.0
x4,
short
lengh
Slo
t #16 P
CIe
2.0
x8,
short
lengh
Slo
t #15 P
CIe
2.0
x8,
short
lengh
Slo
t #14 P
CIe
2.0
x8,
short
lengh
Slot #7 PCIe 2.0 x8, short length
Slot #3 PCIe 2.0 x8, short length
US
B #
3
10 Gb
Ether 8
10 Gb
Ether 7
Local View LCD Display
Slot #4 PCIe 2.0 x8, short length
Slot #5 PCIe 2.0 x4, short length
Slot #6 PCIe 2.0 x8, short length
DVD / Blue Ray
Hard disk drives ( VI )Hard disk drives ( VI )
Operating
Panel
Video
Slo
t #8
PC
Ie 2
.0 x
8,
inte
rnal R
aid
slo
t
Slo
t #15
PC
Ie 2
.0 x
8,
short
lenght
Slo
t #14
PC
Ie 2
.0 x
8,
short
lenght
Slo
t #13
PC
Ie 2
.0 x
8,
short
lenght
Slo
t #12
PC
Ie 2
.0 x
8,
short
lenght
PH
P
Slo
t #11
PC
Ie 2
.0 x
8,
short
lenght
PH
P
Slo
t #17
PC
Ie 2
.0 x
4,
short
lenght
Slo
t #16
PC
Ie 2
.0 x
8,
short
lenght
2.5" SAS #4 2.5" SAS #62.5" SAS #0 2.5" SAS #2
2.5" SAS #1 2.5" SAS #3
Slo
t #10
PC
Ie 2
.0 x
8,
short
lenght
PH
P
Slo
t #9
PC
Ie 2
.0 x
8,
short
lenght
PH
P
Extension slots:
external SCSI / RAID controller ( VIII ), Fiber Channel ( IX ), Communication/Network ( X )
FR
ON
T V
IEW
USB #7
USB #6
USB #5
2.5" SAS #5 2.5" SAS #7
CP
UM
EM
R #
4
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
3
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
2
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
1
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
8
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
7
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
6
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
CP
UM
EM
R #
5
with
1x C
PU
so
cke
t a
nd
16
x D
IMM
slo
ts
Fujitsu Technology Solutions PRIMERGY Server 3 of 17
PRIMERGY-Software Configurators and Release ListsStart "PRIMERGY RX900 S1" PRIMERGY RX900 S1 Status 2011-12-30
Section O SW Configurator 64 bit (EM64T / IA64)
with OEM-Software without OEM-Software
for PRIMERGY Server for PRIMERGY Server
OEM- SW is bound to HW and
For all SW products please refer to the corresponding is not allowed to be ordered
software configurator accessible via the Extranet under separately.
"Configuration & Tools, -All configurations, -Software, Exceptions: VMware SW,
URL see below. Citrix XenServer
VMware-Software
- VirtualCenter Management Server for any server released for Windows Server 2003
- Virtual Infrastructure 3 for PRIMERGY > except all mono PRIMERGY systems
- ESX2 for PRIMERGY RX/TX300S2, RX/TX600S3, BX620S2, BX630 Dual/Quad, BX630 8-way
Microsoft Hyper-V Server and System Center
- Microsoft System Center Virtual Machine Manager Workgroup Edition for any server released for Windows Server 2008 R2
- Microsoft System Center Essentials Management Suite for any server released for Windows Server 2008 SP2
- Microsoft Hyper-V Server 2008 R2
Microsoft - Windows Server 2008 R2 Server Licenses Linux - Software *) **)
- Windows Server 2008 R2 Datacenter # Open Enterprise Server ***)
- Windows Server 2008 R2 Enterprise only - SuSE Linux ES (OEM): LO
- EM64T - Red Hat EL (OEM): LO
Microsoft - Windows Server 2008 Server Licenses
- Windows Server 2008 Datacenter PRIMECLUSTER *)
- Windows Server 2008 Enterprise - Clustering
- - Load Balancing
Microsoft - Windows Server 2003
- Windows Server 2003 R2 if end of certification date is still ok
-
-
-
only MultiPath, Duplex Data
EM64T Manager (DDM)
Windows, Linux (W-DDM) Details eg. version numbers are published
on the page referred to
*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under
Manageability Software: V**) https://partners.ts.fujitsu.com/com/products/software/cluster%20technology/primecluster/Pages/default.aspx
- iRMC advanced Pack
only - RemoteView Software
EM64T - RemoteView Service Board **) Pay attention to release and order information in PRINCE -> Operating System
- RemoteView Diagnosis https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
- RemoteDeploy
***) Supply over distribution or procurement from FSC VP BC Software
You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses:
for internal users: http://sp.ts.fujitsu.com/dmsp/docs/osrel.xlsx
for partners: https://partners.ts.fujitsu.com/com/products/servers/primergy/Pages/default.aspx
Continue with PRIMERGY
HW configurator
Fujitsu Technology Solutions PRIMERGY Server 4 of 17
System configurator and order-information guideStart PRIMERGY RX900 S1 PRIMERGY RX900 S1 Status 2011-12-30
Section I Basic unit
PRIMERGY RX900 S1 Baseboard with
- Intel 7500 chipset with serial QPI links (Quick Path Interconnect)
Rack unit 8U with - 16 PCI-Express Slots
- 2 hot-plug power supplys (additional PSU as option) 2x PCIe 2.0 x4 (half length)
- 4 CPUMemory Boards (CPUMEMR) (up to 4 additional boards optional) 14x PCIe 2.0 x8 (half length)
- LCD-Display for LocalView (Service Display) - 8x socket for CPUMEMR
- 8 bays for 2.5" SAS/SATA HDD`s - SATA controller on-board (for ODD)
- Power cord for rackmounting (ICE 320 C14->C19 plug) - iRMC S2 (integrated Remote Management Controller)
- no Rack- mounting kit included with graphics controller and 10/100Mbit Service LAN-port
- 6x 1GBit LAN Ports on-board (WOL-capable)
Base Unit S26361-K1361-V800 - 2x 10GBit LAN Ports on-board
- SAS RAID controller as option
- ServerView Suite Software package
incl. ServerStart, ServerBooks, Management Software and Updates
Interfaces:
Front side
- 3x USB 2.0
- 1x VGA (15 pin)
Rear Side
S26361-F2735-E111 S26361-F2735-E109 - 2x USB 2.0
No Rackmount-Kit option RMK RX900 - 1x VGA (15 pin)
Only for loose deliveries telescopic rails - 1x RS-232-C (serial, 9 pin)
No mounting in Racks possible - 6x onboardLAN RJ45, 2x onboardLAN SFP+, 1x ServiceLAN RJ45
max. 1x per system consisting of Internal
- 1 pair of telescopic rails - 1x internal USB Interfaces for backup device
with screws and washers - 1x internal port for UFM (uSSD) Module (Embedded vSphere ESXi 4.0)
no PS/2 connection for KB / Mouse (USB must be used instead)
1x per system
S26361-F2735-L109
RMK RX900 for Server Drop-in
S26361-F4530-E13 S26361-F4530-E10 telescopic rails
Mounting in Mounting in for loose delivery
asymmetrical racks (3U bracket) symmetrical racks
max. 1x per system max. 1x per system S26361-F2735-L7
Lateral cable management for RX900
S26361-F2735-E17 S26361-F2201-E20 mounted in asymmetrical racks
Cable management for RX900 2U cable arm behind systems for loose delivery
- for asym. PRIMECENTER racks - for symmetrical PCR M1
- not for 3rd party - or for 3rd party racks S26361-F2201-L20
max. 4x per system max. 3x per system 2U cable arm mounted behind systems
in symmetrical PCR M1 or 3rd party racks
for loose delivery
S26361-F2735-L31
PRIMECENTER S2 or M1 Racks Support Bracket 3 HU for mounting
in asymmetrical racks
1x per system
SNP:SY-F1647E301-P
Installation ex works for one "Rack-mounting ex factory"
server or subsystem. This service is to be ordered once
Hereby the rack will be delivered per installable server/storage
completely pre-mounted and subsystem, in order to get the
all wired connections are tested. server/storage subsystem
With racks 12U, 24U, 38U: mounted into the PRIMERGY racks.
Systems and components In case of the 46 U PRIMERGY Rack,
will be delivered installed in the rack this service has to be ordered,
With racks 46U: to get the mounting kits and the
Systems and components cables installed.
will be delivered separately
To be ordered only together with
a PRIMERGY PRIMECENTER rack
e.g.:
S26361-K826-V10x
refer configurator PC-Rack
max. 1x per System
A
Fujitsu Technology Solutions PRIMERGY Server 5 of 17
System configurator and order-information guideA PRIMERGY RX900 S1 Status 2011-12-30
Section II Processor
4 CPU Memory Riser (CPUMEMR) and 4 CPU's must be configured as minimum, as mamimum 8 are possible.
Later upgrading to a 6 or 8 processor system is also possible,
but requires possibly adding of PSU modules.
Extension CPUs must be identical to the already installed CPU´s.
4 CPU Memory Riser (CPUMEMR) are part of the
Base Unit S26361-K1361-V800
S26361-F4470-E100
CPUMEMR - CPU Memory Riser Board
A minimum of 4 CPUMEMR must be configured
- 1x CPU Socket for Intel Xeon processor 7500 series
with 1066 or 1333MHz Frontside Bus incl. passive heat sink
- 16 Memory DIMM Slots for DDR3 DIMM
- 4x SMI on each CPUMEMR
Max 8 CPUMEMR per System
Following CPU´s can be configured max. 8x per system
A minimum od 4 CPU´s must be configured
Xeon E7540 6C/2,00GHz/18M/6,4GT/s (105W) S26361-F4471-E540 extended lead time
4x Xeon X7542 6C/2,66GHz/18M/5,8GT/s (130W) S26361-F4471-E542
Xeon X7550 8C/2,00GHz/18M/6,4GT/s (130W) S26361-F4471-E550
Xeon X7560 8C/2,26GHz/24M/6,4GT/s (130W) S26361-F4471-E560 extended lead time
B
Fujitsu Technology Solutions PRIMERGY Server 6 of 17
System configurator and order-information guideB PRIMERGY RX900 S1 Status 2011-12-30
Section III Memory
C
Memory configuration modes Interleaving Mode In RX900 S1 Memory Interleaving Mode is default and set by BIOS. Hemisphere Mode RX900 S1 supports Hemisphere Mode from 5 - 8 CPU configuration default and set by BIOS up to 4 CPU configuration support non Hemisphere Mode only. Spare Mode Spare mode is not supported in RX900 S1 Mirroring mode To use Mirroring Mode you have to order the Mirroring Mode option - S26361-F4472-E3 In mirroring mode, all data are copied within the main memory. Therefore only 50 % of the total memory is available for the operating system. Two types of mirroring modes are available: Intrasocket Mirroring - Memory Mirroring within CPUMEMR Memory will be mirrored from one memory controller to the other memory controller within the same CPU. Intrasocket Mirroring is possible for all CPU up to 4 CPUs. When enabling Memory Mirroring in case of 4 socket configuration, same DIMMs must be populated between DDR channel (ABCD) and (EFGH). Memory Mirroring is configured within CPUMEMR. This means same size of DIMMs must be populated as below - DIMM# (1B, 1D, 1F, 1H) should be same size of DIMMs. - DIMM# (1A, 1C, 1E, 1G) should be same size of DIMMs. - DIMM# (2B, 2D, 2F, 2H) should be same size of DIMMs. - DIMM# (2A, 2C, 2E, 2G) should be same size of DIMMs. Intersocket Mirroring - Memory Mirroring between CPUMEMR Memory will be mirrored from one memory controller to an memory controller on another CPU. Intersocket mirroring is only possible with 6 or 8 CPUs. When enabling Memory Mirroring in case of 6 or 8 socket configuration, all four DIMMs must be same size within CPUMEMR. - DIMM# (1B, 1D, 1F, 1H) should be same size of DIMMs. - DIMM# (1A, 1C, 1E, 1G) should be same size of DIMMs. - DIMM# (2B, 2D, 2F, 2H) should be same size of DIMMs. - DIMM# (2A, 2C, 2E, 2G) should be same size of DIMMs. In addition to this, same configuration must be kept between CPUMEMR (1,2), (3,4), (5,6), (7,8) because Memory mirroring will be configured between CPUMEMRs.
Memory Mirror for up to 4-S (Intra-Socket Mirroring)
Memory Mirror for 6-S and 8-S (Inter-Socket Mirroring)
Memory DIMM population Order
Fujitsu Technology Solutions PRIMERGY Server 7 of 17
System configurator and order-information guideC PRIMERGY RX900 S1 Status 2011-12-30 0
Max. Capacity / Features
The system can be equipped with up to128 DIMMs (distributed on 8 CPUMEMRiser boards)
Each DIMM slot can optionally be equipped with 2GB, 4GB, or 8GB DDR3 DIMM modules,
so the maximal memory size is 1024GB with 8GB modules.
ECC with SDDC (Chipkill) is standard for RX900 S1.
Max. Memory Speed depends on CPU QPI Speed, but is limited to 1066 MHz.
S26361-F4472-E3
Mirrored Mode Installation
BIOS setup for Mirrored mode
Preinstallation ex factory
max. 1x per system
S26361-F4472-E643 S26361-F4472-E644 S26361-F4472-E645
Memory 8GB Memory 16GB Memory 32GB
min. DDR3 DDR3 DDR3
2x consisting of consisting of consisting of
mem 4x 2GB modules 4x 4GB modules 4x 8GB modules
upgr. occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots
max. 32x per system max. 32x per system max. 32x per system
S26361-F4472-E643 S26361-F4472-E644 S26361-F4472-E645
Memory 8GB Memory 16GB Memory 32GB
up to 3x14x DDR3 DDR3 DDR3
memory consisting of consisting of consisting of
upgrades 4x 2GB modules 4x 4GB modules 4x 8GB modules
occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots
max. 32x per system max. 32x per system max. 32x per system
S26361-F4470-E100 Upgrade path is
CPUMEMR - CPU Memory Riser Board - 2x CPUMEMR and 2 CPUs
A minimum of 4 CPUMEMR must be configured for CPUMEMR slot 5 and 6
- 1x CPU Socket for Intel Xeon processor 7500 series - 4x CPUMER and 4 CPUs
2 or 4x with 1066 or 1333MHz Frontside Bus incl. passive heat sink for CPUMEMR slot 5 to 8
- 16 Memory DIMM Slots for DDR3 DIMM
Other CPUMEMR upgrades
max. 4 CPUMEMR per System are not supported!
One of the following CPU´s must be configured
per CPU Memory Riser Board
E7540 (6 core 2.00Ghz / 18M / 6.4GT/s 105W / HT) S26361-F4471-E540
2 or 4x X7542 (6 core 2.67Ghz / 12M / 5.8GT/s 130W) S26361-F4471-E542
X7550 (8 core 2.00Ghz / 18M / 6.4GT/s 130W / HT) S26361-F4471-E550
X7560 (8 core 2.26Ghz / 24M / 6.4GT/s 130W / HT) S26361-F4471-E560
S26361-F4472-E643 S26361-F4472-E644 S26361-F4472-E645
Memory 8GB Memory 16GB Memory 32GB
DDR3 DDR3 DDR3
up to 16x consisting of consisting of consisting of
memory 4x 2GB modules 4x 4GB modules 4x 8GB modules
upgrades occupies 4 memory slots occupies 4 memory slots occupies 4 memory slots
max. 32x per system max. 32x per system max. 32x per system
D
Fujitsu Technology Solutions PRIMERGY Server 8 of 17
System configurator and order-information guide
D PRIMERGY RX900 S1 Status 2011-12-30
Section IV USB devices / optical devices
Setup RX900 S1 by SV Installation Manager is supported with following configurations:
built in CD/DVD or USB CD/DVD, no Floppy disk drive:
UNC Network share reachable
Following USB Components are available
1) USB DVD SM / Blu-Ray as soon as available
External SuperMulti Drive
External Blu-Ray Drive
2) USB Keyboard: S26381-K340-V120
KBPC PX D, professional keyboard
3) USB Mouse: S26381-K430-L100
Laser Moue USB/PS2 Combo
4) USB Sticks:
MyUSBS A910 8GB, MLC Flash S26391-F6048-L208
MyUSBS A910 16GB, MLC Flash S26391-F6048-L216
Additionally a monitor can be connected to the VGA 15-pin interface.
S26361-F3531-E2 S26361-F3269-E2
Blu-ray Combo slim SATA DVD-RW supermulti slim SATA
6x BD-ROM, 16x DVD, 40x CD all formats, DUAL/DL, DVD-RAM
1x BD DL and all CD/DVD formats only W2K, W3K and Linux
0.5 x 5.25", black bezel 0.5 x 5.25", black bezel
max. 1x per system max. 1x per system
E
Fujitsu Technology Solutions PRIMERGY Server 9 of 17
System configurator and order-information guideE PRIMERGY RX900 S1 Status 2011-12-30
Section V Hard disk drives
S26361-F3298-E32 S26361-F3298-E64
SSD 32GB SSD 64GB
Solid State Disk Solid State Disk
SATA 3Gb/s SATA 3Gb/s
hot plug/hot replace tray hot plug/hot replace tray
max. 8x per system max. 8x per system
max. 8
SAS 6Gb/s 2.5" with hot plug/hot replace tray
300GB 10000rpm,<4,5ms, 8MB Cache S26361-F4482-E130 configuration of 450GB 10000rpm,<4,5ms, 8MB Cache S26361-F4482-E145 SAS-HDDs requires600GB 10000rpm,<4,5ms, 8MB Cache S26361-F4482-E160 SAS RAID controller900GB 10000rpm,<4,5ms, 8MB Cache S26361-F4482-E190
73GB 15krpm,<4,5ms, 8MB Cache S26361-F4482-E573
146GB 15krpm,<4,5ms, 8MB Cache S26361-F4482-E514
max. 8x per system
SSD SAS 2.5"
S26361-F4541-E100 S26361-F4541-E200 S26361-F4541-E400
SSD SAS 100GB, SLC SSD SAS 200GB, SLC SSD SAS 400GB, SLC
Solid State Disk Solid State Disk Solid State Disk
SAS 6Gb/s SAS 6Gb/s SAS 6Gb/s
Enterprise Perfomance Enterprise Perfomance Enterprise Perfomance
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
max. 8x per system max. 8x per system max. 8x per system
Section VI PCIe-SSD
only on special release
S26361-F4522-E321 S26361-F4522-E641
PCIe-SSD 320GB MLC PCIe-SSD 640GB MLC No mix of
ioDrive 320GB ioDrive 640GB 320GB and 640GB SSD
PCIe 1.1 PCIe 1.1 possible
PCIe x4, Low Profile PCIe x4, Low Profile
max. 2x per system max. 2x per system
G
Fujitsu Technology Solutions PRIMERGY Server 10 of 17
System configurator and order-information guide
G PRIMERGY RX900 S1 Status 2011-12-30
Section VII internal SAS RAID 0/1 and RAID5 Controller for HDD´s
S26361-F3554-E512
RAID Ctrl SAS 6G 8port internal
Based on chip LSISAS2108
LSI MegaRAID Modular RAID controller must be ordered, if at least one internal HDD is configured!
512MB Cache with ECC
1x RAID 0, 1, 10, 5, 50, 6, 60
optional BBU
Support for 3Gb/s and 6Gb/s
SATA and SAS hard drives
PCIe x4
Low-profile MD2 form factor
max. 1x per system
S26361-F3257-E170
Cache Battery Backup Unit BBU max. 2x per system possible
with 70cm cable set for loose delivery please order
max. 2x per system S26361-F3257-L110
H
Fujitsu Technology Solutions PRIMERGY Server 11 of 17
System configurator and order-information guide
G PRIMERGY RX900 S1 Status 2011-12-30
Section VIII external SAS controller
The number of max. I/O PCIe controllers highly depends
on the numer of CPUMEMR!
The following Table describes the max. number of PCIe
controller slots
CPUMEMR PCIe slots PCIe slots (PHP)
The showm max. numer of each controller is valid,as far
as the numer of PCIe slots are available also.
A. SAS controller for external backup drives
S26361-F3271-E1
SAS Controller 3Gb/s 8 port
LSI SAS3442E-R
max. 3x PCIe x4, The 3Gb/s SAS Controller is basically for SX10 S2
int: 4 port due to the fact that SX10 S2 supports 3Gb/s only.
ext: 4 port We have to withdraw the controller because it can't
max. 3x per system run under UEFI BIOS.
We will release the controller with UEFI support soon.
Same controller but new order number!
B. SAS RAID controller for JBOD subsystems
S26361-F3593-E1
8 port SAS RAID Controller The RAID controller can be used only for the connection of
LSI external subsystems (FibreCAT SX40, Eternus JX40)
MegaRAID SAS9280-8e 6Gb/s
512MB Cache with ECC Cables for the connection from the RAID Controllers
RAID 0, 1, 10, 5, 50, 6 & 60 to the subsystem see configurator FibreCAT SX40
without iBBU The usage of the internal SAS ports is not supported !
SAS 6Gb/sec
max. 2x 8 port external
PCIe x4, 167mm
full height bracket
max. 2x per system
S26361-F3257-E170
Cache Battery Backup Unit BBU max. 2x per system possible
with 70cm cable set for loose delivery please order
max. 2x per system S26361-F3257-L110
P
0
4
4
4
6
8
7
7
12
Fujitsu Technology Solutions PRIMERGY Server 12 of 17
System configurator and order-information guide
PRIMERGY RX900 S1 Status 2011-12-30P
Section IX Fibre Channel
The number of max. I/O PCIe controllers highly depends
on the numer of CPUMEMR!
The following Table describes the max. number of PCIe
controller slots
CPUMEMR PCIe slots PCIe slots (PHP)
4 7 0
6 7 4
8 12 4
The showm max. numer of each controller is valid,as far
as the numer of PCIe slots are available also.
S26361-F3961-E1 S26361-F3961-E2
8GBit/s FC Controller 8GBit/s FC Controller
Emulex Emulex
LPe1250, full height bracket LPe12002, full height bracket
8x 1 channel 8GBit/sec FC Controller 2 channel 8GBit/sec FC Controller
LC Interface for 50µm Fiber LC Interface for 50µm Fiber
PCIe x4, 170mm PCIe x4, 170mm
max. 8x per system max. 8x per system
All controllers for the connection of external storage systems are delivered without cables.
For the configuration of external cabling see the configurator for external storage systems.
For Fibre Channel SAN also other componets like switches, SFPs and optical wires are
orderable (for details see price liste)
Q
Fujitsu Technology Solutions PRIMERGY Server 13 of 17
System configurator and order-information guide
I PRIMERGY RX900 S1 Status 2011-12-30
Section X Communication / Network
The number of max. I/O PCIe controllers highly depends
on the number of CPUMEMR!
The following Table describes the max. number of PCIe
controller slots
CPUMEMR PCIe slots PCIe slots (PHP)
4 7 0
6 7 4
8 12 4
The shown max. number of each controller is valid, as far
as the number of PCIe slots are available also.
on-board LAN Controller
3x Dual Gbit Ethernet Contr. on-board Teaming: Failover, Load Balancing
Intel 82576 NS (Kawela wo/IPsec) The Intel LAN Controllers Pro 1000MT, 1000MF, 1000PT, 1000PF
can be used with the on-board controller in Teaming Mode
ext: 6x RJ45 connector, Cat 5 Two onboard LAN ports can likewise educate a team.
1x Dual 10Gbit Ethernet Contr. on-board
Intel 82599 (Niantic wo/IPsec) Onboard Ethernet Controller
The onboard controller are configured in the Basic Unit already.
ext: 2x SFP+ connector
while stocks last
S26361-F3555-E900
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit The SFP+ Module is also available as loose delivery
Ethernet FO cabling S26361-F3555-L900
ext:LC-connector Instead SFP+ Modules, SFP+ twinax cables from
max. 2x per adapter the switch vendors may be used
A) Single Port LAN Adapter PCIe
S26361-F3242-E1 (Sheepshead Bay)
Gigabit Ethernet Contr. 1000SX
Eth Ctrl 1x1Gbit PCIe Pro/1000PF LC
Intel PRO/1000 PF Server Adapter
PCIe x4
ext:LC-connector
max. 8x per system
B) Dual Port LAN Adapter PCIe x4/x8
S26361-F3610-E2
Gigabit Ethernet Controller Dual 1000TX
Eth Ctrl 2x1Gbit PCIe x4 D2735 Cu Loose delivery with:
Intel Kawela based 2 port Server Adapter S26361-F3610-L502
8x PCIe x4,
ext: for RJ45-plug, Cat 5
max. 8x per system
C) Quad Port LAN Adapter PCIe x4
S26361-F3611-E1
Gigabit Ethernet Controller Quad 1000TX
Eth Ctrl 4x1Gbit PCIe x4 D2745 Cu
Intel Barton Hills based 4 Port Server Ad.
PCIe x4, Loose delivery with:
ext: for RJ45-plug, Cat 5 S26361-F3611-L501
max. 8x per system
I1
Fujitsu Technology Solutions PRIMERGY Server 14 of 17
System configurator and order-information guide
I1 PRIMERGY RX900 S1 Status 2011-12-30
D) 10GbE 2-Port SFP+ for MMF Module and SFP+ Twinax Cable
while stocks last
S26361-F3555-E1 (Spring Fountain DD) only on special release
10 Gigabit Ethernet Contr. dual port SFP+
Eth Ctrl 2x10Gbit PCIe x8 X520-DA2 SFP+
Intel Ethernet Server Adapter X520-DA2
PCIe x8
ext:SFP+ for MMF LC Module or Twinax cable
max. 8x per system
while stocks last
S26361-F3555-E900 only on special release The SFP+ Module is also available as loose delivery
SFP+ Module MMF 10GbE LC S26361-F3555-L900
SFP+ module for 10 Gbit Instead SFP+ Modules, SFP+ twinax cables from
Ethernet FO cabling the switch vendors may be used
ext:LC-connector
max. 2x per adapter
2
2
S26361-F3629-E2 4
(D2755) 4
10 Gigabit Ethernet Contr. dual port SFP+ 4
4x Eth Ctrl 2x10Gbit PCIe x8 D2755 SFP+ The controller is delivered without SFP+ modules for optical cables, these must be ordered
Intel Niantic based dual port 10Gb NIC separately. Without SFP+ modules copper twinax cables are supported.
PCIe x8, Low Profile, Full Height Bracket The adapter is also available as loose delivery with
ext: 2x SFP+ cage FH and LP bracket included: S26361-F3629-L502
max. 4x per system
S26361-F3986-E3 The SFP+ Module is also available as loose delivery
SFP+ Module MMF 10GbE LC S26361-F3986-L3
SFP+ module for 10 Gbit Instead SFP+ Modules, SFP+ twinax cables from
Ethernet FO cabling the switch vendors may be used
ext:LC-connector
max. 2x per adapter
S26361-F3592-E2
10GBit/s CNA
Emulex Lose Lieferung über: S26361-F3592-L2
OCe10102
2 channel 10GBit/sec CNA
SFP+ Cage The controller is delivered without SFP+ modules for optical cables, these must be ordered
PCIe x8, 170mm separately. Without SFP+ modules copper twinax cables are supported.
max. 8x per system
S26361-F3592-E108
SFP+ Module MMF 10GbE LC
SFP+ module for 10 Gbit The SFP+ Module is also available as loose delivery
Ethernet FO cabling S26361-F3592-L108
ext:LC-connector Instead SFP+ Modules, SFP+ twinax cables from
max. 2x per adapter the switch vendors may be used
J
Fujitsu Technology Solutions PRIMERGY Server 15 of 17
System configurator and order-information guide
J PRIMERGY RX900 S1 Status 2011-12-30
Section XI System Management Products (RemoteView)
S26361-F1790-E241
iRMC S2 advanced pack
integrated remote management controller
activation key for
graphical console redirection
and remote media redirection
max. 1x per system
Be aware of import restrictions!
S26361-F3552-E1 Loose delivery for later
TPM Module integration possible for customer.
Trusted Platform Module on Motherboard
Use according to import restrictions S26361-F3552-L1
max. 1x per system TPM Module add-on kit
for later integration (loose delivery)
Trusted Platform Module on Motherboard
Use according to import restrictions
max. 1x per system
Section XII Optional PSU / power cords
Base system will be shipped with two PSUs and power cords ICE320 C14->C19
for rack installation. Country specific power cords are not required.
S26113-F573-E10
3. power supply module
2000W, hot plug
for 2+1 redundancy
incl. 1x power cord ICE320 C14->C19 (2,5m)
max. 4x per system
For later upgrade the following kit is available:
S26113-F573-E10 S26113-F573-L10
4. power supply module 4. power supply module
2000W, hot plug 2000W, hot plug for 2+2 redundancy for 2+2 redundancy
incl. 1x power cord ICE320 C14->C19 (2,5m) incl. 1x power cord ICE320 C14->C19 (2,5m)
max. 4x per system max. 1x per system
End PRIMERGY RX900 S1
Fujitsu Technology Solutions PRIMERGY Server 16 of 17
System configurator and order-information guide
PRIMERGY RX900 S1 Status 2011-12-30
Change Report
Date Order number Changes
2011-12-21 S26361-F4482-E114 SAS HD 6G 144GB - no longer available
2011-10-10 S26361-F2201-E20 Cable arm adjusted
2011-10-01 S26361-F3298-E64 64 GB SSD - no longer available
2011-05-03 S26361-F3610-E2/L502 Formal change from E1 / L501
2011-03-31 S26361-F3629-E2 10 Gigabit Ethernet controller added
2011-03-18 S26361-F4522-Exxx PCIe SSD added
2010-09-30 S26361-F3611-E1 New Quad LAN GbE controller - now available
2010-09-30 S26361-F3610-E1 New Dual LAN GbE controller - now available
2010-07-01 First Release
Fujitsu Technology Solutions PRIMERGY Server 17 of 17