Presentation On

Security Metal Detectors

© All Rights Reserved

• Mention the words metal detector and you'll get completely different reactions from different people. For instance, some people think of combing a beach in search of coins or buried treasure. Other people think of airport security or the handheld scanners at a concert or sporting event.

• The fact is that all of these scenarios are valid. The metal detectors in airports, office buildings, schools, government agencies and prisons help ensure that no one is bringing a weapon onto the premises.

Introduction

Most Common are following three:

• Very low frequency (VLF) • Pulse induction (PI) • Beat-frequency oscillation (BFO)

Metal Detection Technologies

VLF Technology

• Very low frequency (VLF), also known as induction balance, is probably the most popular detector technology in use today. In a VLF metal detector, there are two distinct coils called Transmitter coil & Receiver coil.

• The metal detector can determine approximately how deep the object is buried based on the strength of the magnetic field it generates. The closer to the surface an object is, the stronger the magnetic field picked up by the receiver coil and the stronger the electric current generated. The farther below the surface, the weaker the field. Beyond a certain depth, the object's field is so weak at the surface that it is undetectable by the receiver coil.

Technologies Continue...

PI Technology

• A less common form of metal detector is based on pulse induction (PI). Unlike VLF, PI systems may use a single coil as both transmitter and receiver

• This technology sends powerful, short bursts (pulses) of current through a coil of wire. Each pulse generates a brief magnetic field.

Technologies Continue...

BFO Technology

• The most basic way to detect metal uses a technology called beat-frequency oscillator (BFO). In a BFO system, there are two coils of wire. If the coil search head passes over a metal object, the magnetic field caused by the current flowing through the coil creates a magnetic field around the object. As the frequency deviates from the frequency of the other coil, the audible beats change in duration and tone. The simplicity of BFO-based systems allows them to be manufactured and sold for a very low cost.

Technologies Continue...

• Ferrous metals are magnetic type metals such as steel and iron and are the easiest for metal detectors to find. Non-ferrous metals are non-magnetic metals such as copper, aluminum, brass, bronze, and are almost as easy to detect as ferrous metals. Non-magnetic stainless steel such as types 302, 304, and 316 are by far the most difficult of metals to detect. In general, a piece of non-magnetic stainless steel must be 1½ to 2 times larger than a ferrous piece of metal to be detected by a metal detector.

Types of Metals & Sensitivity

Gate® 4000A Walk-through Metal Detector

Entry Passing LightsSmooth, efficient traffic flow with easy-to-view, eye-level passing lights on the entrance side of each panel.

Overhead Control UnitLCD Display, alarm lights, LED bar graphs and control touchpad plus all wiring, connections and electronics are integrated into the overhead compartment.

High adjustable sensitivityGate® 4000A series walkthrough metal detectors gate is adjustable. In the highest volume, articles as small as a paper clip can be detected and indicated.

Audible and Visual AlarmsAudible alarm and LED lights signals when a target has been detected

Gate® 4000A Continue...

Gate® 4000A is designed for use by authorized personnel with multi-level security codes. It only allows authorized users to change settings.

Password protection

Harmless to human bodyUsing sensitive metal detecting technology is harmless for heartbeat of human body, magnetic tapes, video recording tapes and software disks and Cds.

18 Detection ZonesGate® 4000A offers exclusive multiple targets pinpointingwith 18 distinct zones for full target coverage on the left, centerand right side of the body from head to toe.

InterferenceDual channels and DSP circuitry allow several ST series scanner gates to operate simultaneously in close proximity to one another.

Gate® 4000A Continue...

Traffic CounterGate® 4000A have function to counts the traffic which passed through the walkthrough gate.

DimensionsOuter frame: 2.2 X0.79 X0.54M ( H X W X Depth)Inner frame: 2.0X0.7X0.540M  (H X W X Depth) 

Electric current220V Power: 35VA

Net Weight±80kg

Working Temperature-20°C ~ ±45°C

Standard GB15210-2003 and CE Approved

How it works!

How it works!Continue..

Mate® 3000 Hand-held Metal Detector

Features & Specs: One Switch Operation Ultimate Sensitivity Simple and convenient to use No adjustment is required. Drop voltage up to 7V not effected on detection

distance Low power consumption, 40 hours continuous works Low battery alarm Switch on/off beep prompt function Optional rechargeable battery charger Beep, LED and vibration alarm modes

Mirror® 2000 Under Vehicle Inspection Mirror

Features & Specs: 6 styles selection available Available in 12" round convex or flat acrylic

mirror Equipped with adjustable swivel for infinite

adjustment Heavy-duty extruded rubber rim to help prevent

damaging objects when maneuvering Available with tripod ball bearing caster

wheels, allowing full range of motion with effortless maneuvering Lightweight with adjustable handle

Low 3.5" ground clearance Available with flashlight, batteries and

mounting bracket for indoor or outdoor usage

Thank you