Upload
dothu
View
223
Download
0
Embed Size (px)
Citation preview
SHORT COURSES: JULY 8, 2018 • CONFERENCE: JULY 9-12, 2018Stewart Center, Purdue University, West Lafayette, Indiana, USA
PRELIMINARY PROGRAM
Compressor Engineering2018 Purdue Conferences
Refrigeration and Air ConditioningHigh Performance Buildings
24th Compressor Engineering
17th Refrigeration and Air Conditioning
5th High Performance Buildings
Hosted by
Purdue Center for High Performance Buildings
Ray W. Herrick Laboratories
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
Climate Technologies
ABOUT THE CONFERENCEIt has been a tradition since 1972 for the Ray W. Herrick Laboratories at Purdue University to sponsor a venue for exchanging ideas, information and cutting-edge research in the area of refrigeration technology, compressors, high performance buildings and closely related fields. In today’s economy, it is important to maintain your professional contacts and to keep current on the latest research. Thus, plan to join us in July 9-12, 2018!
REGISTRATION INFORMATION
AUTHOR INFORMATION
CONTACT INFORMATION
Best Student Paper AwardAs in past conferences, there will be three Best Student Paper Awards for each of the three conferences. Award dollars for these top papers are sponsored by Johnson Controls. 1st place papers will receive $1000, 2nd place papers will receive $500 and 3rd place papers will receive $250.
GuidelinesIn order to qualify for the Best Student Paper Award, the first author of the paper must have been a full-time student at the time of the paper submission. Nominations for the award must be submitted by the faculty advisor of the student author or by the Principal Investigator of the work. An individual faculty member may only nominate 2 student papers for the award total (across the three conferences).In the nomination letter, the nominator must 1) provide the paper number and paper title, 2) affirm that the student was the primary contributor to the ideas and results presented in the paper and 3) describe the merits and novelty of the research presented in the paper. The deadline for nomination submission is April 30, 2018 and the submissions must be sent via email to the corresponding conference chair. The email addresses of the conference chairs are as follows. • Compressor Conference - Dr. W. Travis Horton - [email protected] • Refrigeration and Air-conditioning Conference - Dr. James E. Braun - [email protected] • High Performance Building Conference - Dr. Thanos Tzempelikos - [email protected]
Deadlines
Monday, April 2, 2018 Manuscript Submission DeadlineMonday, April 30, 2018 Manuscript Acceptance DeadlineMonday, April 30, 2018 Best Student Paper Award Nomination DeadlineMonday, May 21, 2018 Final Papers must be uploaded to Conftool
For Conferences and Short CoursesKim Stockment177 S. Russell St.West Lafayette, IN 47907, USAPH: (765) 494-6078Fax:(765) 494-0787E-mail: [email protected]
For Registration and PaymentEthan Kingery128 Memorial Mall, Stewart Center,Room 116, West Lafayette, IN 47907PH: (765) 496-3667Fax: (765) 494-0567E-mail: [email protected]
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
Conference Only Registration
Conference and IBO Workshop Deadlines
Presenting Author Registration (3 Presented Papers Maximum) $650 $750 April 2, 2018Student Author Registration (3 Presented Papers Maximum) $250 $350 April 2, 2018Non-Author Registration $700 $800 May 21, 2018Student Non-Author Registration $300 $400 May 21, 2018Short Course Registration $650 May 21, 2018Student Short Course Registration $250 May 21, 2018
All registration rates will increase by $150 after the deadline date. Groups of 6 attendees from the same employer receive 1 complimentary registration for every 5 paid registrations. Group registration fees are $3,500 before May 21, 2018 and $4,000 after May 22, 2018.
Guest options available: Guest opening Reception Ticket $25. Guest Steak Barbeque Ticket $50.
Register at: www.conf.purdue.edu/2018HLConferences
KEYNOTE AND PLENARY SPEAKERSAndy Pearson - Group Managing Director, Star Refrigeration, Ltd.Innovation in Refrigeration and Air-Conditioning In the last 30 years or so the amount spent on research and development in the refrigeration and air-conditioning sectors seems to have reached unprecedented heights, driven mainly by the phase out of traditional refrigerants and their replacement by a variety of solutions including new fluids which have similar performance but are less harmful to the environment than those that they replace, new ways to use even older substances such as ammonia, carbon dioxide, water and air and new ways of achieving cooling without using the Perkins cycle. Despite this massive effort the core technology used to provide refrigeration in residential, commercial and industrial systems has not changed much. It is in fact pretty much the same as in was 60 years ago.
Ed Arens - Director, Center for the Built Environment - University of California, BerkleyPersonal comfort system research at the Center for the Built Environment, University of California BerkeleyThe engineered indoor environment consists almost entirely of systems in which temperature and humidity are controlled while air movement and other asymmetrical influences are minimized. Such systems are simple to visualize, design, and control. They are however inherently electricity-intensive, and consume in aggregate a large fraction of the world’s energy. They also leave at least 20% of their occupancies dissatisfied. Future buildings will save energy and improve satisfaction by using personal comfort systems (PCS) having the ability to offset a widened range of indoor temperatures while also overcoming the variability in occupant individual preferences. Per occupant, PCS requires two orders of magnitude less energy than central systems, while delivering equivalent or better comfort. It also can address
Jack Elson - Retiree, Emerson Climate TechnologiesThe Past, Present & Future of Reciprocating Compressors Reciprocating compressor technology has offered a unique contribution to the gas compression needs of mankind as we progressed from the earliest efforts to pressurize air to the multiple applications today for reliable efficient compressors for both refrigeration and air conditioning usage. Beginning with the need for air flow to increase fire temperature for early metalworking, pressurized air has been an important contributor to applications such as construction, mining and the industrial revolution in general. The early reciprocating air compressors used for this purpose became the foundation for early refrigerant compressors used for both household refrigerators and residential air conditioning. Both reciprocating compressor design technologies and the vapor compression cycle were necessary inventions to lead the way
Reciprocating compressor product development has benefited significantly from the instrumentation and analytical tools developed to better understand and improve product durability and performance. These will be reviewed along with a review of future development possibilities for the reciprocating compressor.
Reinhard Radermacher - Co-founder of the Center for Environmental Energy EngineeringFuture Perspectives of AC/R/HPBefore a backdrop of technology development in general and challenges facing our society at large, the presentation will explore opportunities for energy efficiency in buildings in general and HVAC&R in particular. Emphasis is placed on vapor compression, refrigerant choice and include a brief discussion of non-vapor compression systems and their components. The presentation will conclude with examples of the potential contributions resulting from a systematic approach to component and system optimization.
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
In this wide-ranging and thought-provoking review of innovation in refrigeration and air-conditioning Andy Pearson considers why this might be. He starts with a basic explanation of what innovation is and looks at some examples of good innovation from other fields. He considers what defines someone as an innovator and whether these characteristics are innate or can be learned. Using practical examples he encourages the audience to think like an innovator then looks at some of the areas in which innovation has flourished over 30 years. The review also considers areas in which the refrigeration and air-conditioning industry has been less successful in innovating and concludes by looking to the future and imagining what new pressures might come to bear and how we can best respond to them.This presentation should be of interest to everyone who is engaged in research and development, whether as a practical technician or theoretical scientist, or as a senior executive responsible for managing the development process, as a financier responsible for funding it or as a technology user who is eagerly waiting for the next improvement to arrive.
the significant metabolic transients experienced by people in the workplace. Finally, PCS enables inherently efficient passive and radiant building systems to respond more quickly and be viable outside their normal climatic ranges.The Center for the Built Environment at UC Berkeley studies building technology in laboratory and field studies, addressing energy impacts and environmental quality from both building and occupant perspectives. To translate findings to practice, it collaborates with over 40 industry partners, contributes to professional and regulatory codes and standards, and has been spawning startups that commercialize its work.
to a practical solution for modern food preservation and environmental comfort. These will be reviewed along with a review of reciprocating compressor evolution and the various technology challenges and developments required to improve both durability and efficiency as the product type evolved from external drive, to semi-hermetic, to hermetic design variations. Today all product types have successful applications with such examples as external drive for automotive AC and transport refrigeration, semi-hermetic for commercial refrigeration and AC, and hermetic for household refrigeration and residential AC and heat pump.
MONDAY, JULY 9
TUESDAY, JULY 10
7:00am-4:00pm Conference Registration – East Foyer, Stewart Center
8:00am-10:00am Welcome Continental Breakfast – West Foyer, Stewart Center
8:00am - 4:00pm Conference Hospitality Room (Refreshments Available) – STEW 302/306
9:30-11:30 am Opening Session, Welcome and Keynote Address – Loeb Playhouse, Stewart CenterInnovation in Refrigeration and Air-Conditioning - Andy Pearson, Group Managing Director, Star Refrigeration, Ltd.
11:30-1:00 pm Chairpersons & Presenting Authors Lunch (Monday’s Sessions Only) – West Faculty Lounge, Second Floor, Purdue Memorial Union
11:30-1:00 pm Lunch Break
STEW 214A&B STEW 214C&D STEW 218A&B STEW 218C&D STEW 310 STEW 278 STEW 202 STEW 206
1:00-3:00 pm B1: Control-Oriented
Modeling (IBO)
B2: Building Envelope,
Facade and Lighting Systems
R1: Commercial and Industrial Refrigeration I
R2: Organic Rankine Cycles
R3: Heat Pump Design and Assessment
R4: Heat Exchanger
Design Improvements
C1: Screw Compressors I
C2: Linear and Automotive Compressors
3:00-3:30 pm Coffee Break - (Hospitality Room)
3:30-5:30 pm B3: Model Predictive
Controls I (IBO)
B4: Net Zero Energy Buildings
R5: Domestic Refrigeration I
R6: Vapor Compression
Cycle Enhancements I
R7: Steady-State Vapor
Compression System
Modeling
R8: Heat Exchanger
Design Optimization
C3: Spool and Rotating Vane Compressors
C4: Linear Compressors
3:30-5:30 pm Student Branch ASHRAE Meeting - STEW 314
5:30-6:00 pm Shuttle
6:00-8:00 pm Opening Reception – Lafayette Brewing Company (LBC) Main Street, Lafayette, IN – Hosted by UT Carrier
8:30-9:00 pm Shuttle
7:15-8:15 am Complimentary Breakfast for Chairpersons & Presenting Authors (Tuesday’s Sessions Only) – West Faculty Lounge, 2nd Floor, Purdue Memorial Union
8:00am - 10:00am Continental Breakfast Available – West Foyer, Stewart Center
8:00am - 4:00pm Conference Hospitality Room (Refreshments Available) – STEW 302/306 Conference Registration
8:30-9:30 am Plenary Session – Loeb Playhouse, Stewart CenterPersonal comfort system research - Ed Arens, Director, Center for the Built Environment, University of California, Berkley
9:30am - 9:45am Coffee Break - (Hospitality Room) – STEW 302/306
STEW 214A&B STEW 214C&D STEW 218A&B STEW 218C&D STEW 310 STEW 278 STEW 202 STEW 206
9:45-11:45 am B5: Model Predictive
Controls II (IBO)
B6: Heat Pump Systems
R9: Heat Exchanger Frost Characterization
R10: Evaluation of Low GWP
Refrigerants I
R11: Vapor Compression
Cycle Enhancements II
R: Student Paper Competition
C5: Tribology and
Lubrication I
C6: Scroll I
12:00pm-1:15 pm Conference Luncheon – North and South Ballrooms, Purdue Memorial Union
1:30-3:30 pm B7: Occupant-based Control and Modeling
(IBO)
B8: Building Simulation and Optimization I
R12: Heat Exchanger Frost
Impacts and Control
R13: Lubricant Selection, Analysis &
Management
R14: Transient Vapor
Compression System Modeling
C: Student Paper Competition
C7: Screw Compressors II
C8: Valves I
3:30-4:00 pm Coffee Break - (Hospitality Room) – STEW 302/306
4:00-6:00 pm B9: Grid-Responsive
Systems and Controls I
B10: Thermal Storage Systems
and Materials
R15: Air-Side Heat Transfer
Characterization
R16: Two-Phase Ejector, Injector and Separator
Analysis
R17: Alternative Refrig, AC and
HP Technologies
B: Student Paper Competition
C9: Expanders C10: Reciprocating Compressors I
4:00-5:30 pm IIR Commissions B1, B2 & E1, E2 Combined Business Meetings – STEW 314
6:00-8:00 pm Tours - ReNEWW House & DC Micro-Grid House
6:00-11:00 pm Free Time
6:30-8:00 pm Conference Advisory Committee Meeting (by invitation only)
8:00-10:00 pm Student Mixer – O’Bryan’s Nine Irish Brothers
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
7:15-8:15 am Complimentary Breakfast for Chairpersons & Presenting Authors (Wednesday’s Sessions Only) – West Faculty Lounge, 2nd Floor, Purdue Memorial Union
8:00am - 10:00am Continental Breakfast Available – West Foyer, Stewart Center
8:00am -12:00pm Conference Registration – East Foyer, Stewart Center
8:00am - 4:00pm Conference Hospitality Room (Refreshments Available) – STEW 302/306
8:30-9:30 am Plenary Session – Loeb Playhouse, Stewart Center The Past, Present & Future of Reciprocating Compressors – Jack Elson, Retiree, Emerson Climate Technologies
9:30am - 9:45am Coffee Break - (Hospitality Room) – STEW 302/306
STEW 214A&B STEW 214C&D STEW 218A&B STEW 218C&D STEW 310 STEW 278 STEW 202 STEW 206
9:45-12:00pm B11: Model Predictive
Controls III (IBO)
B12: Building Simulation and Optimization II
R18: HVAC & R Equipment
Fault Impacts & Diagnostics (IBO)
R19: Domestic Refrigeration II
R20: Expansion Devices
R21: Transportation
Air-Conditioning
C11: Rotary Compressors I
C12: Compressor Modeling I
12:00-1:00 pm Lunch Break
1:00-3:00 pm B13: Data-Driven Modeling and Diagnostics
(IBO)
B14: Occupant Comfort and
Modeling
R22: Advanced Equipment
Controls I (IBO)
R23: Commercial
and Industrial Refrigeration II
R24: Boiling Heat Transfer
Characterization and Enhancement
R25: HVAC Equipment
Performance Measurement
C13: Testing and
Measurements
C14: Scroll II
3:00-3:30 pm Coffee Break - (Hospitality Room) – STEW 302/306
3:30-5:30 pm B15: Grid-Responsive
Systems and Controls II (IBO)
B16: IAQ, Ventilation and Airflow
Modeling
R26: Advanced Equipment
Controls II (IBO)
R27: Heat Exchanger Modeling
R28: Two-Phase Flow
Characterization
R29: Evaluation of Low GWP
Refrigerants II
C15: Tribology and Lubrication II
C16: NVH I
5:45-6:15 pm Shuttle - Departing from Grant Street PMU Entrance
6:00-10:00 pm Informal Steak Barbeque – The Trails, West Lafayette, IN – Hosted by Emerson Climate Technologies
9:30-10:00 pm Shuttle - Departing from Grant Street PMU Entrance
7:15-8:15 am Chairpersons & Presenting Authors Breakfast (Thursday’s Sessions Only) – West Faculty Lounge, 2nd Floor, Purdue Memorial Union
8:00am - 10:00am Continental Breakfast Available – West Foyer, Stewart Center
8:00am - 4:00pm Conference Hospitality Room (Refreshments Available) – STEW 302/306
8:30-9:20 am Plenary Session – Loeb Playhouse, Stewart Center Future Perspectives of AC/R/HP - Reinhard Radermacher, Co-founder of the Center for Environmental Energy Engineering
9:30am - 9:45am Coffee Break - (Hospitality Room) – STEW 302/306
STEW 214A&B STEW 214C&D STEW 218A&B STEW 218C&D STEW 310 STEW 278 STEW 202 STEW 206
9:45-12:00pm B17: Building Control
Strategies (IBO)
R30: Material and
Manufacturing Impacts
R31: HVAC & R Equipment Performance
Enhancement I
R32: Condensation Heat Transfer
R33: Refrigerant Pressure Drop
Characterization and Impacts
C17: Screw Compressors III
C18: Rotary Compressors II
C19: Compressor Modeling II
12:00-1:00 pm Lunch Break
1:00-3:00 pm B18: Smart Devices and Appliances
R34: Property Measurements
and Assessments
R35: Heat Exchanger
Performance Characterization
R36: Absorption Technologies
R37: HVAC & R Equipment Performance
Enhancement II
C20: NVH II C21: Compressor Modeling III
C22: Novel Compressors
3:00-3:30 pm Coffee Break - (Hospitality Room) – STEW 302/306
3:30-5:30 pm B19: Building Analysis and
Retrofits
R38: Property Modeling
R39: Heat Transfer in
Microfin Tubes and
Microchannels
R40: Dessicant Systems
R41: Residential Heat Pumps for
Water and Space Heating
C23: Valves II C24: Scroll III C25: Reciprocating Compressors II
3:30-5:30 pm Conference Advisory Committee Meeting (by invitation only) – STEW 314
5:00pm End of Conference
*IBO = Intelligent Building Operations Session
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
WEDNESDAY, JULY 11
THURSDAY, JULY 12
ORGANIZING COMMITTEE
SHORT COURSES AND WORKSHOP
General Chair .............................................................................................................................................................................................................. Eckhard A. GrollRefrigeration and Air Conditioning Conference Chair ................................................................................................................................................... James E. BraunRefrigeration and Air Conditioning Conference Co-Chair ..................................................................................................................................................... Neera Jain Compressor Conference Chair ..........................................................................................................................................................................................Travis HortonCompressor Conference Co-Chair ....................................................................................................................................................................................Davide ZivianiHigh Performance Buildings Conference Chair ..................................................................................................................................................... Thanos TzempelikosHigh Performance Buildings Conference Co-Chair ..........................................................................................................................................................Brandon Boor
Compressor 103: Generalized Simulation Framework for Positive Displacement Compressors and ExpandersIn this third edition of the compressor modeling short course, a generalized simulation framework for the modeling of positive displacement compressors and expanders will be presented. Such a model is very useful during the design and optimization phases and helps identify major losses. A comprehensive overview on the state-of-art of mechanistic models of positive displacement machines will be given. Due to the fact that all the mechanistic models present a similar structure, a generalized modeling platform has been developed and validated at the Ray W. Herrick Laboratories. The generalized platform will be used to demonstrate the flexibility of such modeling tool on dealing with different numerical challenges associated with leakage flows, friction losses, thermal network, and control volumes among others. Reciprocating, rolling piston and scroll compressors will be used as main examples. In particular, the theoretical presentations will be integrated with practical examples in the Python programming language. The goal of the short course is to give a solid background on positive displacement modeling that can be further employed and developed by researchers.Organizers: Davide Ziviani (Purdue University), Orkan Kurtulus (Purdue University)
The Transition to Flammable RefrigerantsCFC refrigerants were developed in 1928 as nonflammable, nontoxic alternatives to the common chemicals in use at that time. These chemicals allowed refrigeration and air conditioning equipment to be placed in all forms of human housing, workplaces, and transportation. While toxicity was perhaps the more critical factor, nonflammable refrigerants could be used with fewer restrictions than was required for flammable alternatives. The need for refrigerants with more benign environmental impacts has made mildly flammable refrigerants a likely option for widespread adoption in the near term. The introduction of flammable gases will require substantial changes in many common manufacturing, testing, installing, and servicing aspects of HVAC&R equipment to comply with current and future safety codes.The short course speakers will discuss the basics of fire dynamics in refrigerants, flammability tests and standards, and safety code requirements for the use of flammable gases in various building applications. Updates to international equipment standards and recent research results that address HVAC components for flammable refrigerants will also be presented. Finally, changes in equipment installation, service, and refrigerant handling will be covered, along with changes in employee training that will likely be required for those involved in these areas. Recognized experts in refrigerant flammability, pertinent safety codes, and flammable refrigerant applications will share their knowledge and experiences in discussing changes that will be required for the next generation of refrigerants.*Electronic presentation files will be provided to all participants. Those attending the short course should bring a laptop computer to follow along and take notes.Organizers: Bill Murphy (University of Kentucky, retiree)
2018 Intelligent Building Operations WorkshopThis will be the fourth in a series of workshops that bring together researchers and developers of intelligent building features and systems. The goal is to gain a better understanding of the state of intelligent building technologies and to identify existing gaps that should be addressed in future research and development. The one-day workshop will feature selected presentations of case studies that highlight recent developments and demonstrations of advanced sensing, control and diagnostic technologies, occupant interactions, and grid interactions. The format will encourage an open discussion to address what is necessary to move from research to widespread adoption of intelligent building technologies. The marketplace has been slow to offer these high-level features because of high implementation costs associated with site-specific solutions. This workshop will focus on technology solutions that can enable scalable and cost-effective intelligent building operations. In addition to the workshop, several technical sessions will be held during the International High Performance Buildings Conference that address technological developments critical for achieving scalable and cost effective intelligent building operations. Presentations will be supplemented with papers that are part of the proceedings of the conference. A single registration fee will cover participation in both the IBO Workshop and the HPB Conference. In addition, participants will be able attend any of the technical sessions associated with the Purdue International Compressor and Refrigeration and Air Conditioning Conferences, which are held concurrently.Organizers: Jim Braun (Purdue University), Gregor Henze (University of Colorado), Panagiota Karava (Purdue University), and Neera Jain (Purdue University)
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF
ACCOMMODATIONS
TRAVELING INFORMATION
Conference attendees are responsible for making their own housing reservations. Guests are encouraged to choose from our list of preferred accommodations, which are listed below and on our website. (https://engineering.purdue.edu/HerrickConf) You can choose from full service hotel facilities in and around the Purdue University area, as well as our University Residences. Conference organizers have worked together to negotiate conference rates for you. Please be sure to mention you are attending the Compressor Conference to ensure these rates.
Many of our area hotels offer a courtesy shuttle to campus, and attendees should make arrangements for transportation to the conference facilities with their respective hotels.
If you are traveling to Purdue via air transportation, the closest destination cities are Indianapolis & Chicago. Once on the ground, there are several shuttle services which offer service to Purdue University. To learn more about shuttle service, rental car options & maps of campus, please visit our website under the Visitor Info tab. (https://engineering.purdue.edu/HerrickConf)
If you require a visa invitation letter to attend the conferences, please contact us as soon as possible. Presenting authors can find invitation letters available through Conftool.
If you are not a presenting author, but wish to attend our conferences please check out the VISAS tab under Visitor Information on our website to learn more about acquiring your Invitation letter and other paperwork necessary to attend.
Purdue Union Club Hotelwww.union.purdue.edu101 N. Grant Street, West Lafayette, IN 47906800-320-6291 • 765-494-8913
Four Points by Sheraton West Lafayettewww.starwoodhotels.com1600 Cumberland Avenue, West Lafayette, IN 47906800-777-9808 • 765-463-5511
Holiday Inn City Centerwww.hicclaf.com515 South Street, Lafayette, IN 47901800-423-1137 • 765-423-1000
University ResidencesFirst Street Towerswww.housing.purdue.edu/Housing/Residences/FirstStreetTowers/index.html1250 1st Street, West Lafayette, IN 47906Book room at First Street Towers when registering for the conference.
10000 250 500
A P P R O X I M A T E S C A L E I N F E E T
Cherry Lane
John R. Wooden D
rive
Evergreen St.
Dodge St.
Meridian St.
Chelsea Rd.
Bexley Rd.
Northridge Dr.
ToU.S.
Purdue& Research
Park
231
52
126
Stev
en C
. Bee
ring
Dr.
Tower Dr.
Ade Dr.
Hill
top
Dr. Steven C. Beering D
r.
1
2
3
4
5 619
20
16
12
13
14
15
2526
2730
32
3123
2829
17
18
78
9
10
11
24
21
22
McCorm
ick Road
McCorm
ick Road
Dav
id R
oss R
oad
Stadium Ave.
526
Stadium Ave.
Third St.
Fourth St.
Fifth St.
Sixth St.
First St.
State St.State St.
State St.State St. Russ
ell S
t.
S. R
usse
ll St
.
Gat
es R
d.
Arn
old
Dr.
Halsey D
r.
Air
port
Rd.
Wal
dron
St.
Ova
l Dr.
Uni
vers
ity
St.
Uni
vers
ity
St.
S. U
nive
rsit
y St
.
Mar
stel
ler S
t.
Shee
tz S
t.
Hor
t Dr.
John
R. W
oode
n D
r.
Second St.
N. M
arti
n Ji
schk
e D
r.
First St.
S. M
arti
n Ji
schk
e D
r.
S. Marti
n Jischke Dr.
Duh
me
Dr.
Mac
Art
hur D
r.
Northwestern Ave.
Northwestern Ave.
Stadium Ave.
Stadium Ave.
N. G
rant
St.
Sylvia St.Sylvia St.
Hay
es S
t.
Vin
e St
.
Lutz Ave.
North St.
Chau
ncey
Ave
.
Fowler Ave.
Wiggins St.
Columbia St.
And
rew
Pl.
N. G
rant
St.
S.
Gra
nt S
t.
Chau
ncey
Ave
.Sa
lisbu
ry S
t.
Wood St.
Harrison St.
Harrison St.
Nimitz Dr.
S. R
usse
ll St
.
S. Russell St.
Steely St.
Williams St.
Ahlers Dr.
Ahlers Dr.
Sout
h Ri
ver R
d.
State St.
Third St.
Air
port
Roa
d
Marshal Drl .
ON
E W
AY
ON
E W
AY
ONE
WAY
ONE
WAY
ON
E W
AY
ONE WAY
ONE WAY
ONE WAY
ONE WAY
ONE W
AY
ONE WAY
ONE
WAY
231
231
H LOT
H LO
T
KampenGolf Course
Ackerman HillsGolf Course
CattailTrail toPurdue
ResearchPark To William Daniel
Turf Center (DANL)
To soccer complex, SchwartzTennis Center, Grand Prix Trackand Alexander Field
DrivingRange
BirckBoilermaker Golf
Complex
SCHO
GCMB
GSMB
WGLRSPURVOIN
OLMN
DYE
STADIUM
LOT
HilltopApts.
David RossMemorial
and Garden
TowerAcres
FORD
TRNR
BTV
OWEN
SCPA
HLTPA LOT
F LOT
LAMB
MACK
CARY
MOLL
STDMBRES
(CQNE)(CQNW)
(CQW
)
(CQE
)
(CQS)
PurdueExponentEE
AR
MSEE
FRNY
HAMP PHYS
WANG
CTSSKRCH
C
ARMS
RHPH
SCHL
ELLT
HOVD
PUSH
PGNW
ME
JNSN
RAIL
TARK
WILY
BCC
LCC
LWSN
WDCT
IntramuralGold Fields
BandPractice
Field
BoilermakerSoftball
Complex RankinTrack and
Field
TREC
DMNTAQUA
CREC
CattailTrail
PickettPark
NorthwestAthletic Complex
WEST
Horticulture Park
Intramural PlayingFields
Purdue West
ShoppingPlaza
Purdue Village (PVIL)
PARKINGFACILITIES MRDH
SMLYSHRV
ERHT
HARR
HILL
PGMD
MCUT
SSOF
FSTC
FSTW FSTE
WindsorHalls
WARN
VAWT
SHLY
WOOD
DUHM
FWLR
HNLY
POUL
POANMRG
N
Fou
nd
ers
Par
k
TEL
PGU
PSYC
CL50SC
UNIV
MRR
T
MAT
H
BRNG
REC
STON
HAAS
MTH
W
PRCE
MemorialMall
BALY
POTR
MGL
WTHRBRWN
HEAV GRIS
NUCL
KNOY
Stadium M
all
Purdue
Mall
AcademyPark
PURDUEPOLICE
PMUC
HIKS
STEW PMUPGGPWD
Inte
rnat
iona
lCe
nter
ToStateRoad26E
DAUC
PAO
PGM
YONG
KRAN RAWL
HAWK
PGW
Agricultural Mall
AGAD
HGRH
PFEN
FORS
FPRD
WSL
R
HORT
NLSN
EEL
BSG
FOOD
LSR
BCHM
SMTHLILY
HLAB
GRS
LSA
ABEDRUG
PGH LYLE
HANS
HERL
ASTL
SOIL
MJIS
LSPS
HOCK
DISCOVERY PARK
TERY
PVAB
PVP
BRK
MAN
N
BIND
PJIS
PVCC
DLR
SquirrelPark
KB&S Railroad
Intramural BlackFields
To SIML
To Bow
en Lab
Purdue Airport
HGR5TH1
TERM
FOPN
NISW
AERO
COMP
HGR4ASB
KB&S Railroad
MM
S1
PFSB
PRSVMMDC
ADM
TSWF
GMF
2014, Purdue UniversityCMapK1245U_7291
LMSB
HMMTLMST
ADDL
WADE
FREH
LYNN
EHSB
VCPR
VA1
VA2
AHF
UPOF
SCCA-ENAECC
VPTH
VLAB
DOYL
UPSB
VPRB
VMIFEHSA
UPOB
McC
utch
eon
Dr.
1365 1333
13411325 1317
1309
13011349
1357
13811389
138
137136134
133132
131
201
202
203
204
205 206
207
208 209 210
211212
213
214
215
216
217 218
219
220
221222
223
224225
226
227
140
141 142
143
144
145147
148 149
150
151
146139
228
118
135
1397
KCTR
STEW PMU
HOVD
Bell
Tower
RAWL
HLAB
KEYNOTEPURDUE MEMORIAL UNIONKEYNOTESTEWART CENTER
KEYNOTEHERRICK LABS
KEYNOTERAWLS HALL
SHORT COURSES: JULY 8, 2018 • CONFERENCE: JULY 9-12, 2018 • WEST LAFAYETTE, IN
Compressor Engineering2018 Purdue Conferences
Refrigeration and Air ConditioningHigh Performance Buildings
24th Compressor Engineering
17th Refrigeration and Air Conditioning
5th High Performance Buildings
Hosted by
Purdue Center for High Performance Buildings
Ray W. Herrick Laboratories
Ray W. Herrick Laboratories177 South Russell StreetWest Lafayette, IN 47906-2099
HTTPS://ENGINEERING.PURDUE.EDU/HERRICKCONF