Upload
kee-safety
View
342
Download
3
Tags:
Embed Size (px)
Citation preview
Range
Weightanka
Wireanka
Accessanka
1
2
Class E Deadweight
Anchor Device
to EN 795:1996ISO 14567
Class E Deadweight Anchor Systemand Class ‘C’
Horizontal Lifeline system
to EN 795:1996
Class B & E Portable
Deadweight Anchor system for
Rope Access to EN 795:1996
Features
For roofs up to 5 degrees pitch
Suitable for wet or dry roof surface
Easy and quick assembly
Galvanised to BS EN ISO 1461
3
4
Base weightsBase weights fully encased in rubber
Rubber moulding means base weights aren’t prone to peeling
Unique design adds to performance
Reduces thermal bridging
5
Galvanised Counter weightsEach counterweight weighs 25kg and incorporate carrying handles
Different roof types require different Counterweight quantities
6
PlacementEnsure outside of Kee Anchor product is at least 2.5m from any roof edge, open void or fall hazard.
• Do not position in areas where there is a risk of contamination or accumulation of water, oil, grease or algae
• On Gravel covered roofs, brush gravel to allow anchor bases direct contact with roof material
7
PlacementSuitable Roof Types- Up to 5º Pitch
Concrete
Asphalt Mineral Felt
Stone chippings
Single ply membrane (Smooth)
Steel cladding
8
LimitationsUse with suitable PPEEnsure roof structure is suitable, any doubts Kee Safety recommends seeking the advice of a structural engineer
9
Fall Restraint
Combination of anchor position and PPE supplied ensures no user is able to reach a position of 0.5m of any roof edge, roof open or other fall hazard
10
Cleaning/Storage
The assemblies should be kept clean, using detergent if necessary, by wiping or hosing down with clean water and dried.Storage should be in a dry, chemically inert environment, away from sources of damage and Store in such a way that dismantled products will not become lost or misplaced.Where the Weightanka has been left in position an optional cover is available.
11
Before installationIt is strongly recommended that installers assemble and disassemble one in a place of safety, away from the worksite to familiarise themselves with the product
12
Class E Deadweight Anchor Device toEN 795:1996ISO 14567
CE Certified to PPEDirective
13
14
Portable, Non Penetrative, Temporary or permanent solution
• Ideal for Where Roof build up is unknown• No Roof Alterations required• Good for refurbishment projects• Quick to assemble• No part of the Weightanka weighs more than 25kg
15
Number Of Users
Fall Arrest- Single User
Restraint- Two Users• Tell Kee Safety at time of purchasing• Supplied with 2nd Eyebolt & Restraint PPE disc.
16
Number of weights250kg (Six Galvanised weights) assembly for:
Asphalt/MasticMineral Felt Concrete (Brushed) Stone chippings on Bitumen
300kg (Eight Galvanised weights) assembly for: • Single ply membrane (Smooth)• Steel cladding • (Brushed) Stone chippings on Asphalt/Mastic.
17
Stack weights opposite each other vertically
18
Assembly TOOLS REQUIRED FOR
ASSEMBLY:
12mm A/F Hex Allen key
19
Class ‘E’ Deadweight Anchor System
and Class ‘C’ Horizontal Flexible Lifeline
to EN 795:1996 and BS 7883
CE Certified to PPEDirective
20
21
Non penetrative EN795 ‘Class C’ Wire cable systemAllows users to be continuously attachedUp to 15 m spansFor temporary or permanent installationNo need to water proofSystem incorporates cornersFall arrest or restraint
22
Non penetrative EN795 ‘Class C’ Wire cable systemAllows users to be continuously attachedUp to 15 m spansFor temporary or permanent installationNo need to water proofSystem incorporates cornersFall arrest or restraint
23
Layout optionsSINGLE EXTREMITY ANCHORS
Fall Arrest for a single user
-Or alternatively-
• Fall Restraint for up to 3 users (maximum 2 users in a single span)
24
Layout optionsDOUBLE EXTREMITY/CORNER ANCHORS
Fall Arrest for 2 users in separate spans
25
Edge distances and maximum spansFALL ARREST SYSTEMS
FALL RESTRAINT Maximum 10 m spans Minimum edge distance of 2.5m
15m12m10m8m6m5mMaximum span
7.2m6.6m6.2m5.8m5.4m5.2mMin. Free Fall Distance
4.0m4.0m3.0m3.0m2.5m2.5mMin. Edge Distance
26
Portable Deadweight System for Rope Access
Conforms to BS EN 795, & ISO 14567 class B&E
CE Approved to PPE Directive
Single user for Roped Access applications
• Two users in a rescue situation
27
28
Separate anchor points for working line and back up lineInternal force balanced system allows the assembly to remain static.Requires no attachment to structural membersEasily moved across roof surface, removing need for multiple attachment points Rope lines held away from edge of building reducing risk of abrasion
29
Used with a 250kg Weightanka Assembly for any roof type Sold separately for use with existing Weightanka or as complete systemAluminium, galvanised and rubber coated partsMinimum maintenanceProvides full fall arrest protection before approaching edge
30
UsageAccessanka is an accessory to Weightanka and must always be used in combination with it.This combination provides a mobile deadweight anchor device for use in rope access systems in accordance with:Industrial Rope Access Trade Association (IRATA)
guidelinesand/or:
BS7985:2002 – Code of practice for the use of rope access methods for industrial purposes
31
More information
Identification labelsAssembly and operating instructions Sales LiteratureSales teamTechnical supportwww.keesafety.co.uk
Kee Safety Ltd
32
1 Boulton RoadReadingRG2 0NHUnited KingdomTel: +44 (0) 118 931 1022Fax: +44 (0) 118 931 1146Email: [email protected]