Upload
owen-lane
View
217
Download
0
Tags:
Embed Size (px)
Citation preview
Polar Missionsand
Geographic Positioning Systems
Presented by Rob Snyder
Several IPY Expeditions are now collecting data on “traverses” of
Antarctic .
http://www.ipy.org/index.php?ipy/detail/ipy_expeditions_2007_8/
Norwegian and American scientists are traversing across some of the least known parts
of East Antarctica to expand our knowledge about the effects of climate change in the Cold
Continent..
http://traverse.npolar.no/norwegian-american-ipy-traverse/
A vehicle pulls the living module for the scientists across the Antarctic Plateau. 20 steel
drums underneath the living module do not supply
enough fuel for the entire transect.
http://passporttoknowledge.com/polar-palooza/wmv/nordic03a.php
GPS devices are used to locate fuel depots on the route of the traverse..
The South Pole is the final destination of the Norwegian U.S.
Scientific Traverse.
http://www.fourmilab.ch/cgi-bin/Earth
A network of GPS satellites orbiting Earth
can be used to collect data in Polar regions and guide Polar Expeditions..
http://commons.wikimedia.org/wiki/Image:ConstellationGPS.gif
In this YouTube video, GPS devices are being deployed at many locations in
Antarctica to detect the movement of land and ice.
http://www.ipy.org/index.php?ipy/multimedia/&view=1649/
Handheld GPS devices use microwaves
to communicate with the network of satellites.
http://www8.garmin.com/manuals/GPS72_OwnersManual.pdf
Handheld GPS devices can indicate:
► The coordinates of a location► The elevation at a location► In what direction you are going
(Heading)► In what direction you should be going
(Bearing)► How fast you are moving► How far you have traveled► And much more
There are 2 ways for the polar scientists to navigate to a fuel
depot.► They can be given the coordinates
for the locations of fuel depots. In this case they would use the “GPS Information Page” of a Garmin GPS.
► Locations of the fuel depots can be saved in a GPS unit as “waypoints”. In this case they would use the GOTO function and the “Pointer Page” of a Garmin GPS.
Your Challenge Today
► Use the UMass campus to create a model of a polar traverse that includes the location of a base station, 2 fuels depots and a final destination.
► Record the coordinates for the base station, fuel depots and the final destination.
► Name and save the locations of a base station, 2 fuel depots, and a final destination as “waypoints”.
► Follow a route created by another team of “explorers”.
The Parameters
►Each leg of the route should be no Each leg of the route should be no longer than 100 meters.longer than 100 meters.
►Each team traverses to a different Each team traverses to a different destination so that data can be destination so that data can be compiled that describes a large compiled that describes a large area.area.
►Each team records data in a journal Each team records data in a journal with reference to landmarks.with reference to landmarks.
Getting Started with a Garmin GPS
Power On/Off
The PAGE button will switch off initial warning message and toggle among the various screens.The ROCKER.
scrolls up and down through option.
When you are inside a building, you can use the Simulator to become familiar with the Garmin 72 pages and data fields.
The Simulator Mode
► Turn on the GPS► Press ENTER to clear a warning statement.► Press MENU.► Start Simulator will be highlighted ► Press ENTER► You will see some recently acquired data
that includes Latitude, Longitude, and Elevation.
► Use the PAGE button to view different screens.
The GPS Information Page will indicate how many satellite signals you are
receiving, your coordinates, and your elevation.
Latitude and Longitude angles that originate at the center of
Earth describe the coordinates of a location..
Earth Science: The Challenge of Discovery; D.C.Heath and Co. 1991
Latitude and Longitude Systems
The coordinates for locations can be expressed as Degree, Minutes, and Seconds. This system is used on USGS Topographic maps
For example: 41º 20’ 37” N, 71º 56’ 17” W
There are other ways to indicate coordinates. Meteorologists often indicate the location of Atlantic Ocean hurricanes in Degree Decimal form.
For example: 22.76 N, 59.45º W
You can change how Latitude and Longitude is expressed while in the
simulator mode. This procedure is on Page 5 of GPS Basics. A very similar
procedure for establishing North Reference is also on Page 5.
► Press MENU.► Press MENU again.► Use the ROCKER to highlight “setup”.► Press ENTER► Use the ROCKER to move to the right to the
Units Tab and highlight the Location Tab.► Press ENTER.► Use the ROCKER to highlight your choice. You
may need to scroll up to some options.► Press ENTER► Press PAGE
When you go outside, you will need to turn on your GPS unit and
wait until you receive at least 4 satellite signals.
Directions for turningon the Garmin GPS are on Page One of GPS Basics.
Then you will need to name and save your base station, both fuel depots,
and final destination as “waypoints”
This process is also described on Page One of GPS Basics.
Use the GPS Information Page to record waypoint data in a
journal.
Data can include: Latitude
Longitude Elevation Identifying
features of the area.
When you have reached your final destination you can use GOTO to
navigate back to the Base Station.
Use the ROCKER. to highlight the waypoint that will be your destination.
Press GOTO to display the waypoints stored in the GPS
.
3. Press ENTER to select the waypoint that you want to GOTO.
This is described on Page Three of GPS Basics
The Pointer Page can indicate Bearing and Distance to Base Station
One Data Field needs to indicate Bearing
Another Data Field needs to indicate Distance to Next.
See Page 4 of GPS Basics to change displays in Data Fields.
Heading and Bearing on the Pointer Page
The Black Arrow shows compass direction (bearing) to your selected waypoint
The Line at top of Compass dial shows the direction you are walking (heading).
Heading and Bearing are also measured in degrees.
http://academic.brooklyn.cuny.edu/geology/leveson/core/linksa/mapcomp.html
Summary of Tasks1. Make sure that your GPS
receives sufficient satellite signals for navigation.
2. Go to a location outside of Hasbrouck Lab. Mark, name, and save the location of your base station.
3. Use the latitude and longitude coordinates on the GPS Information Page to collect data.
4. Save and name the locations of fuel depots and your final destination.
5. Once you are at your final destination, use the GOTO to get bearing and distance to your Base Station..
Trading Routes
► Trade journals and GPS units with another team.
► Decide which of the following strategies you will use to locate a fuel depot.
Option 1: Use the GPS Information page to navigate to the coordinates recorded in a journal. The coordinates on the GPS Information page will change as you move.
Option 2: Use the GOTO function to guide you to the location of a fuel depot that has been named and saved as a waypoint.