Upload
others
View
18
Download
0
Embed Size (px)
Citation preview
Passionately Powered
Plugreen Solar Micro-Inverter Systems
PGM-200P-230
PGM-230P-230
PGM-260P-230
Plugreen Corporation,
Laattakatu 13, 08150 Lohja, Finland
Phone : +358 40 1525086
www.plugreen.com
Installation and Operations Manual
Contact Information
1
Please read this very carefully 1
Safety Instructions 1
2
How the solar micro-inverter works 2
Plugreen solar micro-inverter models 2
3
Parts required to install micro inverter 3
Installation Procedure 4
Step 1 - Install the AC Branch Circuit Junction Box 5
Step 2 - Mount the Plugreen Solar micro-inverters on the rack 5
Step 3 - Lay the AC common cable along the rack using mounting hooks 5
Step 4 - Connect the individual micro inverter on the common cable 5
Step 5 - Ground the system using suitable copper wire 5
Step 6 - Completing the Plugreen Installation Map and Connecting the PV Modules 6
4
5
Ground Fault 8
Other Faults 8
Troubleshooting an Inoperable Solar micro-inverter 8
Disconnecting the Plugreen Solar micro-inverter from the PV Module 9
6
Technical Considerations 10
Technical Specifications 10
Plugreen Solar micro-inverter Operating Parameters 10
Voltage and Frequency Limits for Utility Interaction 11
7
Plugreen Corporation Warranty 12
Plugreen Installation Map 15
Important Safety Information 1
Plugreen Solar micro-inverter System 2
Plugreen Solar micro-inverter Installation 3
Commissioning 7
Troubleshooting 8
Technical Data 10
Appendix 12
Table of Contents
1 Important Safety Information
Important Safety Information
The following safety symbols indicates the safety hazard conditions, this needs to be taken care to
reduce the risk of electrical shock and to ensure the safe installation and operation of the Plugreen
Solar micro-inverter.
: This indicates a situation where failure to follow instructions may cause a serious
hardware failure if not applied appropriately. Use extreme caution when performing this task.
: This indicates information particularly important for optimal system operation. Follow these
instructions closely.
Read this very carefully
WARNING
NOTE
Safety Instructions
Perform all electrical installations in accordance with all local electrical codes and the National
Electrical Code (IEC).
Be aware that only qualified personnel should install and/or replace Plugreen Solar micro-inverters.
Do not attempt to repair the Plugreen Solar micro-inverter; it contains no user-serviceable parts. If it
fails, please contact Plugreen customer service to obtain an RMA number and start the replacement
process. Tampering with or opening the Plugreen Solar micro-inverter will void the warranty.
Before installing or using the Plugreen Solar micro-inverter, please read all instructions and cautionary
markings in the technical description and on the Plugreen Solar micro-inverter system and the PV-
array.
Connect the Plugreen Solar micro-inverter to the electrical utility grid only after receiving prior approval
from the utility company.
Be aware that the body of the Plugreen Solar micro-inverter is the heat sink and can reach a
temperature of 80 C. To reduce risk of burns, do not touch.
Do NOT disconnect the PV module from the Plugreen Solar micro-inverter without first removing AC
power.
§
§
§
§
§
§
§
NOTE: For Plugreen Solar micro-inverter Warranty Terms and Conditions, see the Appendix of this
manual.
Copyright Plugreen Corporation. 2011 1-00001 REV 1 1
>
The Plugreen Solar micro-inverter system is a technologically advanced power conversion system for use
in utility-interactive applications. This manual details the safe installation and operation of the Plugreen
Solar micro-inverter.
consists of the following:
Plugreen Solar micro-inverter
Plugreen Common AC cabling system
Plugreen Communication Gateway Unit
Plugreen web-based monitoring software “Insight”
Plugreen Solar micro-inverter System
§
§
§
§
2 Plugreen Solar micro-inverter System
The Plugreen Solar micro-inverter extracts maximum energy from individual photovoltaic (PV) panels.
Each Plugreen Solar micro-inverter is connected to individual PV module. This enables unique intelligent
Maximum Peak Power Point Tracker (iMPPT) of each PV module. By doing so, the single point of failure can
be avoided compared to a string inverter system.
Communication Gateway Unit can be plugged into any two pin standard outlet. The power supply to this unit
is universal so it works from 85 to 265VAC. This unit needs to be installed indoors. Once you connect the
AC power, connect Ethernet cable between the units and your broadband router or modem. Once you
install the Communication Gateway unit, it automatically starts communicating with the centralized web
server. Please log in to the data monitoring web server though Plugreen webpage to understand the data
logging systems and displays.
This integrated system maximizes energy harvest, increases system
reliability, and simplifies design, installation and management.
2Copyright Plugreen Corporation. 2011 1-00001 REV 1
How the Micro-Inverter Works>
>
Plugreen Solar micro-inverters
Broadband
router
AC power cord
PC displaying
data from Insight
Application
Photovoltaicmodules
Ethernet cable
Power LinesPower Lines
Plugreen
communication
Gateway
Plugreen Solar micro-inverter Models
The Plugreen PGM200/PGM230/PGM260 Solar micro-inverters operate with most 60 and 72-cell PV
module configurations. In case of technical enquiries, please contact our Customer support at
1 Plugreen Solar micro-inverter SystemPV systems using Plugreen Solar micro-inverters are simple to install. Each Solar micro-inverter quickly
mounts on the PV racking, directly beneath each PV module. Low voltage DC wires connect from the PV
module directly to the co-located solar micro-inverter, thus eliminating the risk of personnel exposure to
lethal 600Vdc power.
3 Plugreen Solar micro-inverter Installation
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
Before installing the Plugreen Solar micro-inverter, read all instructions and
cautionary markings in the user manual, on the Plugreen Solar micro-inverter, and on the
photovoltaic array.
Perform all electrical installations in accordance with all local electrical codes and the
National Electrical Code (IEC).
Connect the Plugreen Solar micro-inverter to the electrical utility grid only after
receiving prior approval from the utility company.
Be aware that only qualified personnel should connect the Plugreen Solar micro-
inverter to the electrical utility grid.
Be aware that installation of this equipment includes risk of electric shock. Normally
grounded conductors may be ungrounded and energized when a ground fault is indicated.
Parts required for installing the micro-inverter system
Adapter plate
Junction box
Plugreen AC Common Cable
Mounting hooks for AC Common Cable
Grounding conductor
§
§
§
§
§
3Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
Installation Procedure
Installing the Plugreen Solar micro-inverter system involves the following steps:
Installing the AC branch circuit junction box
Mount the Plugreen Solar micro-inverters on the rack
Lay the AC common cable along the rack using mounting hooks
Connect the individual micro inverter on the common cable
Ground the system using suitable copper wire
Connect the PV modules to solar micro-inverters
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Refer the installation diagram below for better understanding
Do not connect Plugreen Solar micro-inverters to the utility grid or energize the AC
circuit(s) until you have completed all of the installation procedures as described in the following
sections
WARNING:
4Copyright Plugreen Corporation. 2011 1-00001 REV 1
WARNING: Do not connect Plugreen Solar Micro Inverter to a off grid like Inverter, UPS or
Generator
Installation Procedure
5Copyright Plugreen Corporation. 2011 1-00001 REV 1
Mount the Junction box plate at a suitable location on the PV racking system (typically at the
end of a row of modules).
Install an appropriate junction box with adapter plate.
: Use electrical system components approved for wet locations only.
Connect the open wire end of the Plugreen AC Common Cable into the junction box using an
appropriate gland or strain relief fitting.
Route the continuous Grounding Electrode Conductor (GEC) through the grounding clamp of
each solar micro-inverter. Check the standards applicable for each country
Installing the AC branch circuit junction box
§
§
§
§
WARNING
STEP 1
Mark the approximate centre of each PV module on the racking system. Typically the location should be
aligning with the PV module junction box.
: Please use the mounting rack in such a way that it allows a minimum of 20mm
between the top of the roof and the bottom of the solar micro-inverter and 25mm between the
back of the PV module and the top of the Micro inverter.
WARNING
Mount the Plugreen Solar micro-inverters on the rack STEP 2STEP 2
Connect the individual micro inverter on the common cable
Each Solar micro-inverter comes with one 3 pin Circular AC connector with a wire length of 60cms.
Connect these AC connectors with the respective female connectors on the AC Common Cable. Unused
connectors on the AC Common Cable should be plugged with the Cap provided.
: AC Common Cable wiring is as: Red – Phase, black- neutral, green – earth/ground
: Make sure protective end caps have been installed on all unused AC connectors.
Unused AC Solar micro-inverter wire harness connectors may be live when the system is
energized by the utility system.
Make sure that size of AC wire gauge is appropriate to take into account of voltage drop
between the AC branch circuit junction box
WARNING
WARNING
NOTE:
STEP 4
Ground the system using suitable copper wire
Each Plugreen Solar micro-inverter comes with a ground clip that can accommodate a 6-10 AWG
conductor. Route a continuous GEC through each of the solar micro-inverters to the NEC approved AC
grounding electrode. The racking and module could be grounded to this conductor using a crimp
connection. An alternative method would be to connect the solar micro-inverter to the grounded racking
using a grounding washer approved for the racking.
STEP 5
STEP 3 Lay the AC common cable along the rack using mounting hooks
WARNING : Ensure that common AC Cable does not hang loose.
Installation Procedure
STEP 6 Connect the PV modules to solar micro-inverters
The Plugreen Installation Map is a diagrammatic representation of the physical location of each Plugreen
Solar micro-inverter in your PV installation. Plugreen creates this map from information that you provide in
a system map. You can use the blank map in the Appendix to record solar micro-inverter placement for
your system. When your map is complete, send it to Plugreen as described below. Plugreen then uses this
information to provide you with detailed information about the performance of your PV system and to allow
you to see a graphic representation of your PV system on the Plugreen ‘Insight’, a web-based monitoring
and analysis. Feel free to provide your own layout if a larger or more intricate installation map is required.
To complete your map
Each Plugreen Solar micro-inverter has a removable serial number label located on the top cover. Peel
the removable serial number label from each Plugreen Solar micro-inverter and affix it to the respective
location on the Plugreen installation map.
Send the installation map to Plugreen at [email protected] after completion. You can also download
installation maps and examples from www.plugreen.com.
After Plugreen creates a graphical representation of your PV system on the website, use the Plugreen
website “Insight” application link to view detailed performance information for your PV system. Please
go to www.plugreen.com for more information on the Plugreen Insight web-based monitoring and
analysis.
§
§
§
To connect your PV modules:
: Completely install all solar micro-inverters and all system inter-wiring connections prior to
installing the PV modules.
Best Practice: Test AC first. Before you rack-mount the PV, pull and terminate all AC wiring, energize the
branches, and power up the solar micro-inverters to make sure that they all report into the
Communication Gateway unit and are operating correctly.
Mount the PV modules above their corresponding solar micro-inverters. Each solar micro-inverter
comes with two oppositely sexed MC4 multi-contact connectors.
First connect the positive DC wire from the PV module to the negatively marked DC connector (female
socket) of the solar micro-inverter. Then connect the negative DC wire from the PV module to the
positively marked DC connector (male socket) of the solar micro-inverter. Repeat for all remaining PV
modules using one solar micro-inverter for each module.
NOTE
§
§
6Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
>
: The AC output neutral is not bonded to ground inside the solar micro-inverter. NOTE
4 Commissioning
WARNING:
§
§
§
§
Connect the Plugreen Solar micro-inverter to the electrical utility grid only after receiving prior
approval from the utility company.
Only qualified personnel must connect the Plugreen Solar micro-inverters to the Utility grid
Ensure that all AC and DC wiring is correct and none of them are damaged
Ensure that all junction boxes are closed properly
Procedure for Commissioning the Plugreen Solar micro-inverter PV system:
Switch on the main circuit breaker on each Plugreen solar micro-inverter branches.
Switch on the main utility-grid AC circuit breaker. The system will start producing power after 3
minutes of System configuration them.
: Since Plugreen solar micro-inverters are powered by PV panels, make sure that sufficient
sun light is available during this process.
The Plugreen solar micro-inverters will start to send performance data over Power Line (PLC)
to the Communication Gateway unit. The time required for all the solar micro-inverters in the
system to report to the Communication Gateway unit will vary with the number of solar micro-
inverters in the system. The first units should be detected within 10 minutes but the entire
system could take hours to detect. Please refer to the Communication Gateway unit Installation
and Operation Manual.
§
§
§
Note
7Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
5 Troubleshooting
Adhere to all the safety measures described throughout this manual. Qualified personnel can use the
following troubleshooting steps if the PV system does not operate correctly:
: Do not attempt to repair the Plugreen Solar micro-inverter; it contains no user-
serviceable parts. If it fails, please contact Plugreen customer service to obtain an RMA number
and start the replacement process.
WARNING
Solar micro-inverter Error Reporting
Please connect the Communication Gateway Unit to the same utility phase on which the solar micro-inverters are connected
Check the status of each solar micro-inverter.
: Please refer the Communication Gateway unit user manual.
Ground Fault:
Please check the Grid Earth and Neutral voltage; it should be as per the standard.
Other Faults:
Please refer the Communication Gateway unit Operations manual.
Note
WARNING
WARNING
WARNING
WARNING
: Be aware that only qualified personnel should troubleshoot the PV array or the
Plugreen Solar micro-inverter.
: Never disconnect the PV wire connectors under load. Please cover the PV module
using an opaque covering sheet prior to disconnecting the module.
: Always disconnect AC power before disconnecting the PV module wires from the
Plugreen Solar micro-inverter. The AC connector of the first solar micro-inverter in a branch circuit
is suitable as a disconnecting means once the AC branch circuit breaker in the load centre has
been opened.
: The Plugreen Solar micro-inverters are powered by DC power from the PV modules.
Troubleshooting an Inoperable Solar micro-inverter
To troubleshoot an Inoperable Solar micro-inverter, follow the steps in the order shown:
Check the connection to the utility grid. Verify that the utility voltage and frequency are within
allowable ranges shown in the Technical Data section on page 10 of this manual. Verify utility
power is present at the inverter in question by removing AC, then DC power. Never disconnect
the DC wires while the solar micro-inverter is producing power.
Check the AC branch circuit interconnection harness between all the solar micro-inverters.
Verify each inverter is energized by the utility grid as described in the previous step.
STEP 1
STEP 2
8Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
>
5 Troubleshooting
Make sure that any AC disconnects are functioning properly and are closed.
Verify the PV module DC voltage is within the allowable range shown in the Technical Data
section on page 10 of this manual.
Check the DC connections between the solar micro-inverter and the PV module.
If the problem persists, please call to customer support at Plugreen.
STEP 3
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
STEP 4
STEP 5
STEP 6
WARNING: Do not attempt to repair the Plugreen Solar micro-inverter; it contains no user-
serviceable parts. If troubleshooting methods fail, please return the solar micro-inverter to your
distributor for maintenance.
Disconnecting the Plugreen Solar micro-inverter from the PV Module
To ensure that the solar micro-inverter is not disconnected from the PV modules under load, adhere to
the following disconnection steps in the order shown:
Disconnect the AC by opening the branch circuit breaker.
Disconnect the first AC connector in the branch circuit.
Cover the module with an opaque cover.
Using a DC current probe, verify there is no current flowing in the DC wires between the PV
module and the solar micro-inverter.
Care should be taken when measuring DC currents, most clamp-on meters must be zeroed
first and tend to drift with time.
Disconnect the PV module wire connectors from the Solar micro-inverter
Remove the Solar micro-inverter from the PV array racking.
9Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
6 Technical Data
Technical Considerations
The Plugreen PGM200/230/260 Solar micro-inverters are designed to operate with most 60 and 72-
cell PV module configurations. Be sure to verify the voltage and current specifications of your PV module
match with those of the solar micro-inverter. For more information, refer to the Plugreen website
(www.Plugreen.com) for a list of approved PV module racking systems and PV modules.
WARNING
WARNING
WARNING
: The panel voltage range should match with the solar micro-inverter input ratings.
: Make sure that the maximum open circuit voltage is within the specs of solar micro-
inverter units.
: Make sure that the maximum short circuit current of PV panels should be less or
equal to the solar micro-inverter specs.
Note: PV module output voltage and current depends on the size and temperature of the PV cells,
also the solar irradiation falling over the panels.
A list of compatible PV modules is maintained on the Plugreen website (www.Plugreen.com).
Technical Specifications
Plugreen Solar micro-inverter - DC Operating Parameters
Parameter/Model Unit Min Typical Max
MPPT voltage range
PGM200/230/260
PGM200/230/260
Maximum DC input voltage
Maximum DC input short circuit current
Maximum DC input current
PGM200/230/260
PGM200/230/260
V
V
A
A
24 38
45
10/11/12
12
10Copyright Plugreen Corporation. 2011 1-00001 REV 1
>
>
6 Technical Data
Plugreen Solar micro-inverter - AC Operating Parameters
Parameter/Model Unit
Unit
Min
Min
Typical
Typical
Max
Max
PGM200/230/260
PGM200/230/260
200/230/260
PGM200/230/260
Output power factor
Maximum AC output Power (-40 to +65 Deg C)
Nominal AC output voltage range
Maximum AC output current
Nominal AC output frequency range
Extended AC output frequency range
High AC Voltage trip limit accuracy
Low AC Voltage trip limit accuracy
Frequency trip limit accuracy
W
Vrms
A
Hz
Hz
%
%
Hz
0.95
211
49.4
49.2
2.5
4
±0.1
0.99
230
.85/1/1.1
50
60
1
264
50.41
50.6
Miscellaneous Operating Parameters
Peak inverter efficiency
CEC weighted efficiency
Nominal MPP tracking efficiency
Total Harmonic Distortion
Operating temperature range
Storage temperature range
%
%
%
%
Deg C
Deg C
- 40
- 40
95
92
>99
5
+ 65
+ 65
Plug Green Micro Inverter Operating Parameters
Dimensions
Weight
Enclosure environmental rating
Cooling
Communication
Standard warranty term
Compliance applicable*
160X138X32mm
1.6Kgs
IP65/NEMA6
Convection
Power Line
15 Years
UL, CE, VDE
11Copyright Plugreen Corporation. 2011 1-00001 REV 1
Note: Specifications are subjected change without notice. *Certifications pending
7 Appendix
Plugreen Corporation Warranty
Plugreen Corporation ("Plugreen") has developed a highly reliable Micro-inverter that is designed to
withstand normal operating conditions when used for its originally intended purpose in compliance with
the Plugreen User Manual supplied with the originally shipped system. The Plugreen limited warranty
("Limited Warranty") covers defects in workmanship and materials of the Plugreen Solar Micro-inverter
("Defective Product") for a period of fifteen (15) years from the date of original purchase of such Micro-
inverter at point of sale to the originally-installed end user location (the "Warranty Period").
During the Warranty Period, the warranty is transferable to a different owner as long as the Micro-
inverter remains installed at the originally-installed end user location. During the Warranty Period,
Plugreen will, at its option, repair or replace the Defective Product free of charge, provided that Plugreen
through inspection establishes the existence of a defect that is covered by the Limited Warranty. Plugreen
will, at its option, use new or reconditioned parts in repairing or replacing the Defective Product. Plugreen
reserves the right to use parts or products of original or improved design in the repair or replacement of
Defective Product. If Plugreen repairs or replaces a Defective Product, the Limited Warranty continues on
the repaired or replacement product for the remainder of the original Warranty Period or ninety (90) days
from the date of Plugreen’s return shipment of the repaired or replacement product, whichever is later.
The Limited Warranty covers both parts and labor necessary to repair the Defective Product, but does not
include labor costs related to un-installing the Defective Product or re-installing the repaired or
replacement product. The Limited Warranty also covers the costs of shipping repaired or replacement
product from Plugreen, via a non-expedited freight carrier selected by Plugreen.
The Limited Warranty does not cover, and Plugreen will not be responsible for, shipping damage or
damage caused by mishandling by the freight carrier and any such damage is the responsibility of the
freight carrier. To obtain repair or replacement service under this Limited Warranty, the customer must
comply with the following policy and procedure:
§ All Defective Products must be returned with a Return Merchandise Authorization Number (RMA)
which customer must request from Plugreen. Before requesting the RMA, however, the customer
should contact Plugreen technical support representative to evaluate and troubleshoot the problem
while the Plugreen Solar Micro-inverter is in the field, since many problems can be solved in the field.
12Copyright Plugreen Corporation. 2011 1-00001 REV 1
7 Appendix
§ Proof-of-purchase of the Defective Product in the form of
(1) the dated purchase receipt from the original purchase, or
(2) the dated dealer invoice or,
(3) purchase receipt from original equipment manufacturer (OEM), or
(4) the dated receipt showing the product was exchanged under warranty.
§ Model number of the Defective Product.
§ Serial number of the Defective Product.
§ Detailed description of the defect.
§ Shipping address for return of the repaired or replacement product.
§ If in-field troubleshooting does not solve the problem, Customer may request the RMA number, which
request must include the following information:
§
§
All Defective Products authorized for return must be returned in the original shipping container or
other packaging that is equally protective of the product.
The returned Defective Product must not have been disassembled or modified without the prior written
authorization of Plugreen.
Plugreen Solar Micro-inverters are designed to withstand normal operating conditions and typical wear
and tear when used for their original intent and in compliance with the installation and operating
instructions supplied with the original equipment. The Limited Warranty does not apply to, and Plugreen
will not be responsible for, any defect in or damage to any Plugreen Solar Micro-inverter: (1) that has been
misused, neglected, tampered with, altered, or otherwise damaged, either internally or externally; (2) that
has been improperly installed, operated, handled or used, including use under conditions for which the
product was not designed, use in an unsuitable environment, or use in a manner contrary to the Plugreen
User Manual or applicable laws or regulations; (3) that has been subjected to fire, water, generalized
corrosion, biological infestations, acts of God, or input voltage that creates operating conditions beyond
the maximum or minimum limits listed in the Plugreen Solar Micro-inverter specifications, including high
input voltage from generators or lightning strikes; (4) that has been subjected to incidental or
consequential damage caused by defects of other components of the solar system; or (5) if the original
identification markings (including trademark or serial number) of such Micro-inverter have been defaced,
altered, or removed.
The Limited Warranty does not cover costs related to the removal, installation or troubleshooting of the
customer's electrical systems. The Limited Warranty does not extend beyond the original cost of the
Plugreen Solar Micro-inverter.
13Copyright Plugreen Corporation. 2011 1-00001 REV 1
The Limited Warranty is the sole and exclusive warranty given by Plugreen and where permitted by law, is
made expressly in lieu of all other warranties, express or implied, statutory or otherwise, including, without
limitation, warranties of title, quality, merchantability, fitness for a particular purpose or non-infringement
or warranties as to accuracy, sufficiency or suitability of any technical or other information provided in
manuals or other documentation. In no event will Plugreen be liable for any special, direct, indirect,
incidental or consequential damages, losses, cost or expenses however arising, whether in contract or
tort, including without limitation any economic losses of any kind, any losses or damage to property or any
personal injury.
To the extent any implied warranties are required under applicable law to apply to the Plugreen Solar
Micro-inverter, such implied warranties shall be limited in duration to the Warranty Period, to the extent
permitted by applicable law. Some countries, states or provinces do not allow limitations or exclusions on
implied warranties or on the duration of an implied warranty or on the limitation or exclusion of incidental
or consequential damages, so the above limitation(s) or exclusion(s) may not apply. This Limited Warranty
gives the customer specific legal rights, and the customer may have other rights that may vary from
country to country, state to or province to province.
7 Appendix
14Copyright Plugreen Corporation. 2011 1-00001 REV 1
Pa
ne
l Gro
up
:
Azi
mu
th:
Tilt
:
Sh
ee
t
of
Cu
sto
me
r C
on
tact
info
rma
tio
n :
Inst
alle
r C
on
tact
info
rma
tio
n :
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
Sti
ck S
ola
r M
icro
-Inve
rte
r s
tick
er
NS
WE
12
34
56
78
91
0
A B C D ma
ps@
plu
gre
en
.co
mS
ola
r p
an
el I
nst
alla
tio
n M
ap
Pa
ssio
na
tely
Po
wer
edC
GU
Do
cum
en
t N
um
be
r R
evi
sio
n
Cir
cle
On
e [
Pa
ne
l Fa
cin
g]
Co
nti
nu
ou
s to
sh
ee
t
Continuous to sheet
Continuous to sheet
Co
nti
nu
ou
s to
sh
ee
t
15Copyright Plugreen Corporation. 2011 1-00001 REV 1
Plugreen Corporation,
Laattakatu 13, 08150 Lohja, Finland
Phone : +358 40 1525086
www.plugreen.com
Contact Information
Passionately Powered