Numbers indicated inside parenthesis ( ) = mm

AD 410 040: Flexible connection piece for VL 200, DN 150 flat

AD 851 041: Connecting piece VL 200 for extension with flat duct DN 150 for extra deep countertop

min.5 ¹⁵⁄₁₆"(110)

¹⁵⁄₁₆"(8.5)

2"(50)

max.

DN 150flat duct

min.25 ⁹⁄₁₆"(650)

6 ⅞"(175)

28 ³⁄₁₆"(716)

20 ³⁄₁₆"(512)

23 ¼"(591)

5 ¹⁵⁄₁₆"(150)

5 ¹⁵⁄₁₆"(150)

8 ¹¹⁄₁₆"(220)

6 ¹¹⁄₁₆"(170)

66 ¹⁵⁄₁₆"(1700)

19 ⅜" (492)

6 ⅞" (175)

3 ⁹⁄₁₆" (90)

1 ³⁄₁₆" (30)

8 ¾" (223)

max. 9 ¹⁄₁₆" (230)min. 2 ¾" (70)

3 ⁹⁄₁₆" (90) 8 ¾" (223)

9 ⁷⁄₁₆" (240) 4 ³⁄₁₆" (107)

8 ¼" (210)

Good to know – for correct planning and installation

– For depth measurements, take account of the depth of the cabinet front and countertop overhangs of the kitchen cabinet.

– With the Vario downdraft ventilation, the ducting is connected to the rear. The respective connecting pieces are available for this purpose.

– Maximum distance between the Vario downdraft ventilation and the blower: Cable length in between 66" (1.7 m)

– For optimum air circulation, we recommend ducts with DN 150.– 2 flat or 2 round ducts must be connected with a pipe connector.– To connect 2 duct bends together (e.g. a 90° horizontal duct bend and a 90°

vertical duct bend), a piece of flat duct is required, which can be shortened to the required length by cutting it to size.

– It is also important that ducting is well sealed in order to prevent air leaks, e.g. by using the adhesive tape AD 990 091 (UV- and heat-resistant).

– Vario cooktops with intensive vapor formation like Vario Teppan Yaki, Vario electric grill should be placed central; in case of Vario electric grill air recirculation is not recommended.

Planning examples with the 200 series downdraft ventilation

www.gaggenau.com/usRevised: 31 March 2020

Numbers indicated inside parenthesis ( ) = mm

Planning example 1VL 200 with AR 410 710 recirculation blowerWall installation, countertop depth 25 ⁹⁄₁₆" (65 cm), access to the filters for replacement from the front.

Good to know– Allow accessibility to the charcoal filters in the base cabinet for their replacement.– Additionally, if the toe-kick is higher than 3 ⅛" (80 mm), the external blower has to

be elevated to enable access to the filters. If the toe-kick is 3 ⅛" (80 mm) high, the blower can be placed directly on the floor.

– For optimum performance, the recirculated air requires sufficient space to escape. Recommend AA 010 410 air exhaust grill (or custom grill).

List of components – 1x AR 410 710 (blower air recirculation)– 1x AD 410 040 (flexible connecting piece for VL 200, DN 150 flat)– 1x AA 010 410 air exhaust grill (or custom grill)

measurements in inches (mm)

19³⁄8"

(492 )±1±¹⁄16"

≤ 1¹⁵⁄16"(≤ 50)

≥ 1¹⁵⁄16"(≥ 50)

≥ 1¹⁵⁄16" (≥ 50)

≥ 3⅛"(≥ 80)

≥ 3⅛"+X(≥ 80+X)

≥ 35¼"+X(≥ 895+X)

14⅝"+X(371+X)

4⅛" (105)

6⅞"(175)

26⅜"(670)

8⅜"(213)

9¾"(247)

21⅝"(550)

31⁹⁄16"(802)

1⁹⁄16"(40) 4⁵⁄16"

(109)4¹³⁄16"(122)

X

Planning example 2 - MetalVL 200 with AR 410 710 recirculation blowerIsland installation, access to the filter for replacement from the front or the back.

Good to know– Allow accessibility to the charcoal filters in the base cabinet for their replacement.– Additionally, if the toe-kick is higher than 3 ⅛" (80 mm), the external blower has to

be elevated to enable access to the filters. If the toe-kick is 3 ⅛" (80 mm) high, the blower can be placed directly on the floor.

– For optimum performance, the recirculated air requires sufficient space to escape. Recommend AA 010 410 air exhaust grill (or custom grill).

List of components– 1x AR 410 710 (blower air recirculation)– 1x AD 851 041 (connection piece for extension with flat duct for extra

deep countertop)– 1x AD 854 000 (flat duct bend connecting piece, metal, DN 150 flat)– 1x AD 854 030 (flat duct bend 90° vertical, metal, DN 150 flat)– 1x AD 410 040 (flexible connecting piece for VL 200, DN 150 flat)– 1x AA 010 410 air exhaust grill (or custom grill)– 1x AD 990 091 (adhesive tape for sealing the ducts, aluminium)

measurements in inches (mm)

X

19³⁄8"

(492 )±1±¹⁄16"

≥ 3⅛" (≥ 80)

≥ 1¹⁵⁄16"(≥ 50)

≥ 25⁹⁄16"(≥ 650)

≥ 25⁹⁄16"(≥ 650)

≥ 1¹⁵⁄16"(≥ 50)

4¹⁵⁄16"(125)

6⅞"(175)

20½"(520)

15⅜"(390)

≥ 30⁵⁄16"+X(≥ 770+X)

4⅛" (105)

≥ 3⅛"+X(≥ 80+X)

9¾"(247)

1⁹⁄16"(40)

14⅝"+X(371+X)

18⅞"+X(480+X)

measurements in inches (mm)

19³⁄8"

(492 )±1±¹⁄16"

≤ 1¹⁵⁄16"(≤ 50)

≥ 1¹⁵⁄16"(≥ 50)

≥ 1¹⁵⁄16" (≥ 50)

≥ 3⅛"(≥ 80)

≥ 3⅛"+X(≥ 80+X)

≥ 35¼"+X(≥ 895+X)

14⅝"+X(371+X)

4⅛" (105)

6⅞"(175)

26⅜"(670)

8⅜"(213)

9¾"(247)

21⅝"(550)

31⁹⁄16"(802)

1⁹⁄16"(40) 4⁵⁄16"

(109)4¹³⁄16"(122)

X

measurements in inches (mm)

X

19³⁄8"

(492 )±1±¹⁄16"

≥ 3⅛" (≥ 80)

≥ 1¹⁵⁄16"(≥ 50)

≥ 25⁹⁄16"(≥ 650)

≥ 25⁹⁄16"(≥ 650)

≥ 1¹⁵⁄16"(≥ 50)

4¹⁵⁄16"(125)

6⅞"(175)

20½"(520)

15⅜"(390)

≥ 30⁵⁄16"+X(≥ 770+X)

4⅛" (105)

≥ 3⅛"+X(≥ 80+X)

9¾"(247)

1⁹⁄16"(40)

14⅝"+X(371+X)

18⅞"+X(480+X)

www.gaggenau.com/usRevised: 31 March 2020

Numbers indicated inside parenthesis ( ) = mm

Planning example 3 - MetalVL 200 with AR 413 722 recirculation blowerIsland/Wall installation, connection from the right side.

List of accessories– 1x AR 413 722 (blower toe-kick)– 1x AD 858 010 (flat duct flex pipe, metal, DN 150)– 1x AD 854 041 (flat duct adapter round, metal, DN 150 flat/round)– 1x AD 413 722 (Oval flex duct)– 1x AA 413 722 (recirculation kit)– 1x AA 010 410 air exhaust grill (or custom grill)– 1x AD 990 091 (adhesive tape for sealing the ducts, aluminium)

尺寸以英吋計（以毫米計）尺寸以英吋計（以毫米計）尺寸英寸(毫米)розміри у дюймах (мм)Ölçüler inç cinsindendir (mm)Mått i tum (mm)mere u colima (milimetrima)dimenzije v palcih (mm)rozmery v palcoch (mm)размеры в дюймах (мм)Dimensiuni în ţoli (mm)medidas em polegadas (mm)wymiary w calach (mm)mål i tommer (mm)Afmeting in inches (mm)Izmēri collās (mm)matmenys coliais (mm)Dimensioni in pollici (mm)méretek hüvelykben (mm)mjere u colima (mm)mesures en pouces (mm)Mitat tuumina (mm)mõõdud tollides (mm)dimensiones en pulgadas (mm)dimensiones en pulgadas (mm)measurements in inches (mm)measurements in inches (mm)measurements in inches (mm)Διαστάσεις σε ίντσες (mm)Maße in Zoll (mm)Maße in Zoll (mm)Mål i tommer (mm)rozměry v palcích (mm)Измерване в инчове (мм)

≥ 1¹⁵⁄16" (≥ 50)

≥ 3¹⁵⁄16"(≥ 100)

≥ 3¹⁵⁄16"(≥ 100)

≥ 49¼"(≥ 1250) 20¹⁵⁄16"

(539)

16³⁄16"(411)

10¹⁄16"(255)

16³⁄16"(411)

20³⁄16"(512)

3¹³⁄16"(97)

16⅛"(409)

12" (305)

12" (305)

6⅞"(175)

21⅝"(550)

7⅜"(187)

7⅜"(187)

15¾"(400)

12" (305)

23⁷⁄16"(595)

6³⁄16"(157)

5¹⁄16"(128)

28⁹⁄16"(725)

3⅞" (98)

19³⁄8"

(492 )±1±¹⁄16"

≤ 1¹⁵⁄16"(≤ 50)

≥ 1¹⁵⁄16"(≥ 50)

19⁵⁄16"(490)

尺寸以英吋計（以毫米計）尺寸以英吋計（以毫米計）尺寸英寸(毫米)розміри у дюймах (мм)Ölçüler inç cinsindendir (mm)Mått i tum (mm)mere u colima (milimetrima)dimenzije v palcih (mm)rozmery v palcoch (mm)размеры в дюймах (мм)Dimensiuni în ţoli (mm)medidas em polegadas (mm)wymiary w calach (mm)mål i tommer (mm)Afmeting in inches (mm)Izmēri collās (mm)matmenys coliais (mm)Dimensioni in pollici (mm)méretek hüvelykben (mm)mjere u colima (mm)mesures en pouces (mm)Mitat tuumina (mm)mõõdud tollides (mm)dimensiones en pulgadas (mm)dimensiones en pulgadas (mm)measurements in inches (mm)measurements in inches (mm)measurements in inches (mm)Διαστάσεις σε ίντσες (mm)Maße in Zoll (mm)Maße in Zoll (mm)Mål i tommer (mm)rozměry v palcích (mm)Измерване в инчове (мм)

≥ 1¹⁵⁄16" (≥ 50)

≥ 3¹⁵⁄16"(≥ 100)

≥ 3¹⁵⁄16"(≥ 100)

≥ 49¼"(≥ 1250) 20¹⁵⁄16"

(539)

16³⁄16"(411)

10¹⁄16"(255)

16³⁄16"(411)

20³⁄16"(512)

3¹³⁄16"(97)

16⅛"(409)

12" (305)

12" (305)

6⅞"(175)

21⅝"(550)

7⅜"(187)

7⅜"(187)

15¾"(400)

12" (305)

23⁷⁄16"(595)

6³⁄16"(157)

5¹⁄16"(128)

28⁹⁄16"(725)

3⅞" (98)

19³⁄8"

(492 )±1±¹⁄16"

≤ 1¹⁵⁄16"(≤ 50)

≥ 1¹⁵⁄16"(≥ 50)

19⁵⁄16"(490)

Planning examples with the 200 series downdraft ventilation

www.gaggenau.com/usRevised: 31 March 2020

Numbers indicated inside parenthesis ( ) = mm

The drawings below show the cut-out dimensions for cooktop combinations of the 200 series. The technician can find the suitable cut-out dimensions for the combinations most frequently used by referring to the previous pages and the drawings below.

Cut-out dimensions for the Vario 200 series Cut-out dimensions for the Vario 200 series with VL downdraft

How to calculate? General Rules.First calculate the overall dimension of the cooktop set up. Do this by adding each unit’s overall width and add ³⁄₁₆" for each connecting strip used. Once you have the final figure for the overall dimension, deduct the overlap of the cooktop set up at each end (starting and ending unit).

Cut-out dimension = Overall dimension. The overlap at each end (total overlap).

Between each unit (cooktops and downdraft) a connecting strip should be placed and added to the overall dimension of the cooktop set up.

The Vario 200 series does not have finishing strips.

When installing only one unit, the cut-out dimension is 10 ⁹⁄₁₆" for the 12" units,22 ¹⁄₁₆" for the VI 263 620 and VG 264 220CA.

11 ⁵⁄₁₆" (288) Appliance – ¹³ ⁄₁₆" (– 20) Overhang 10 ⁹⁄₁₆" (268) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance 22 ⅞" (581) – ¹³ ⁄₁₆" (– 20) Overhang 22 ¹ ⁄₁₆" (561) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance 34 ⁷⁄₁₆" (874) – ¹³ ⁄₁₆" (– 20) Overhang 33 ⅝" (854) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance 45 ¹⁵⁄₁₆" (1167) – ¹³ ⁄₁₆" (– 20) Overhang 45 ³⁄₁₆" (1147) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 22 ¹³ ⁄₁₆"/ (580) Appliance 34 ⅜"/ (873) – ¹³ ⁄₁₆" (– 20) Overhang 33 ⁹⁄₁₆"/ (853) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 5 ¹⁵⁄₁₆" (150) VL 200 17 ⁷⁄₁₆" (443) – ¹³ ⁄₁₆" (–20) Overhang (10+10) 16 ⅝" (423) Cutout

45¹³⁄₁₆"(1164)

5¹⁵⁄₁₆"(150)

5¹⁵⁄₁₆"(150)

5¹⁵⁄₁₆"(150)

5¹⁵⁄₁₆"(150)

16�"(423)

28³⁄₁₆"(716)

34¼"(870)

"

" "

"

""

"

"

" "

"

""

"

"

"

5¹⁵⁄₁₆"(150)

5¹⁵⁄₁₆"(150)

45¹³⁄₁₆"(1163)"

"""

"

"

" "

5¹⁵⁄₁₆"(150)

5¹⁵⁄₁₆"(150)

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 5 ¹⁵⁄₁₆" (150) VL 200 ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance 29" (736) – ¹³ ⁄₁₆" (– 20) Overhang (10+10) 28 ³⁄₁₆" (716) Cutout

5 ¹⁵⁄₁₆" (150) VL 200 ³ ⁄₁₆" (5) VV 200 22 ¹³ ⁄₁₆" (580) Appliance ³ ⁄₁₆" (5) VV 200 5 ¹⁵⁄₁₆" (150) VL 200 35 ¹⁄₁₆" (890) – ¹³ ⁄₁₆" (– 20) Overhang (10+10) 34 ¼" (870) Cutout

11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 5 ¹⁵⁄₁₆" (150) VL 200 ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance ³ ⁄₁₆" (5) VV 200 5 ¹⁵⁄₁₆" (150) VL 200 ³ ⁄₁₆" (5) VV 200 11 ⁵⁄₁₆" (288) Appliance 46 ⅝" (1184) – ¹³ ⁄₁₆" (– 20) Overhang (10+10) 45 ¹³⁄₁₆" (1164) Cutout

Cut-out dimensions for 200 series combinations

www.gaggenau.com/usRevised: 31 March 2020