Embed Size (px)
Citation preview
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
PIPE ROLLER CHAIR FIG. 460 Function: Designed for supporting pipe in applications where horizontal
movement, due to expansion and contraction, will occur but vertical
adjustment is not necessary. The chair can be welded directly to the
steel structure or secured in place through bolt holes.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with
insulation, refer to pipe roller selection guide, which is for use with
pipe covering protection saddles.
Material: Cast iron pipe roller with carbon steel chair, axle, and hex nuts.
(Type 304 or 316 Stainless Steel upon request)
Finish: Plain or electro-galvanized (Hot dipped galvanized with electro-
galvanized hardware upon request)
Approvals: Complies with Federal Specification A-A-1192A (Type 44) and
Manufacturers’ Standardization Society ANSI/MSS SP-58 (Type 44)
which supersedes ANSI/MSS SP-69.
Ordering: Specify figure number, pipe roller size, material, and finish. Order
mounting bolts separately.
Pipe Roller Size
B C D
Recommended Bolt Size
(Not included) E
Max. Rec. Load
Wt. Each
lbs. kN lbs. kg
2 (50) 15/8 (41.28) 11/2 (38.10) 11/4 (31.75) 3/8 x 11/2 300 (1.33) .90 (.41)
21/2 (65) 2 (50.80) 15/8 (41.28) 11/4 (31.75) 3/8 x 11/2 600 (2.67) 1.19 (.54)
3 (80) 21/4 (57.15) 13/4 (44.45) 2 (50.80) 3/8 x 11/2 600 (2.67) 1.48 (.67)
31/2 (90) 25/8 (66.68) 2 (50.80) 2 (50.80) 3/8 x 11/2 600 (2.67) 2.44 (1.11)
4 (100) 23/4 (69.85) 21/4 (57.15) 2 (50.80) 1/2 x 11/2 700 (3.11) 2.85 (1.29)
5 (125) 31/2 (88.90) 21/2 (63.50) 3 (76.20) 1/2 x 11/2 700 (3.11) 3.75 (1.70)
6 (150) 4 (101.60) 23/4 (69.85) 31/4 (82.55) 1/2 x 11/2 1000 (4.45) 5.76 (2.61)
8 (200) 51/8 (130.18) 3 (76.20) 33/8 (85.73) 5/8 x 11/2 1300 (5.78) 8.10 (3.67)
10 (250) 63/8 (161.93) 35/8 (92.08) 51/4 (133.35) 5/8 x 2 1700 (7.56) 12.28 (5.57)
12 (300) 71/2 (190.50) 41/8 (104.78) 51/2 (139.70) 5/8 x 2 2300 (10.23) 20.54 (9.32)
14 (350) 83/8 (212.73) 411/16 (119.06) 61/2 (165.10) 3/4 x 2 3100 (13.79) 25.63 (11.63)
16 (400) 91/2 (241.30) 53/8 (136.53) 81/4 (209.55) 3/4 x 21/2 3900 (17.35) 37.38 (16.96)
18 (450) 101/2 (266.70) 6 (152.40) 91/4 (234.95) 3/4 x 21/2 4200 (18.68) 45.26 (20.53)
20 (500) 115/8 (295.28) 63/8 (161.93) 103/8 (263.53) 3/4 x 21/2 4500 (20.02) 52.35 (23.75)
24 (600) 14 (355.60) 77/8 (200.03) 121/4 (311.15) 7/8 x 31/2 6000 (26.69) 88.00 (39.92)
30 (750) 171/4 (438.15) 95/8 (244.93) 153/8 (390.53) 7/8 x 31/2 7290 (32.43) 147.5 (66.9)
“B” (Center of axle to center of pipe)
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
FIG. 470 & 475 PIPE ROLLER HANGER Function: Designed for suspending pipe in applications where horizontal
movement, due to expansion and contraction, will occur and vertical
adjustment is necessary. The knurled insert provided with Fig. 475
allows easier vertical adjustment.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with
insulation, refer to pipe roller selection guide, which is for use with
pipe covering protection saddles.
Material: Cast iron pipe roller with carbon steel frame, axle, and hex nuts.
(Type 304 or 316 Stainless Steel upon request)
Finish: Plain or electro-galvanized (Hot dipped galvanized with electro-
galvanized hardware upon request)
Approvals: Complies with Federal Specification A-A-1192A (Type 43) and
Manufacturers’ Standardization Society ANSI/MSS SP-58 (Type 43)
which supersedes ANSI/MSS SP-69.
Ordering: Specify figure number, pipe roller size, material, and finish.
NOTE: For Fig. 470 use of an upper locknut ensures proper
performance.
Pipe Roller Size
Rod Size A
B C Adjustment D E Max. Rec. Load Wt. Each
F
lbs. kN lbs. kg
2 (50) 3/8 15/8 (41.28) 25/8 (66.68) 11/16 (26.99) 43/8 (111.13) 3 (76.20) 150 (0.67) 1.05 (.48)
21/2 (65) 1/2 2 (50.80) 23/8 (60.33) 13/16 (30.16) 5 (127.00) 31/4 (82.55) 225 (1.00) 1.29 (.59)
3 (80) 1/2 21/4 (57.15) 31/2 (88.90) 13/4 (44.45) 63/8 (161.93) 37/8 (98.43) 310 (1.38) 1.56 (.71)
31/2 (90) 1/2 25/8 (66.68) 33/4 (95.25) 13/4 (44.45) 7 (177.80) 43/8 (111.13) 390 (1.73) 1.83 (.83)
4 (100) 5/8 23/4 (69.85) 315/16 (100.01) 111/16 (42.86) 71/2 (190.50) 5 (127.00) 475 (2.11) 2.81 (1.27)
5 (125) 5/8 31/2 (88.90) 45/16 (109.54) 19/16 (39.69) 85/8 (219.08) 6 (152.40) 685 (3.05) 4.42 (2.00)
6 (150) 3/4 4 (101.60) 53/8 (136.53) 21/16 (52.39) 101/4 (260.35) 71/8 (180.98) 780 (3.47) 5.98 (2.71)
8 (200) 3/4 51/8 (130.18) 61/2 (165.10) 23/16 (55.56) 123/4 (323.85) 91/4 (234.95) 780 (3.47) 11.42 (5.18)
10 (250) 7/8 63/8 (161.93) 73/8 (187.33) 2 (50.80) 15 (381.00) 111/4 (285.75) 965 (4.29) 17.36 (7.87)
12 (300) 7/8 71/2 (190.50) 83/4 (222.25) 23/8 (60.33) 173/8 (441.33) 131/4 (336.55) 1200 (5.34) 24.62 (11.17)
14 (350) 1 83/8 (212.73) 9 (228.60) 2 (50.80) 187/8 (479.43) 143/4 (374.65) 1200 (5.34) 36.00 (16.33)
16 (400) 1 91/2 (241.30) 93/4 (247.65) 13/4 (44.45) 203/4 (527.05) 167/8 (428.63) 1200 (5.34) 44.00 (19.96)
18 (450) 1 101/2 (266.70) 113/4 (298.45) 23/4 (69.85) 233/4 (603.25) 185/8 (473.08) 1400 (6.23) 54.00 (24.49)
20 (500) 11/4 115/8 (295.28) 121/2 (317.50) 21/2 (63.50) 26 (660.40) 207/8 (530.23) 1600 (7.12) 74.00 (33.57)
24 (600) 11/2 1313/16 (350.84) 161/2 (419.10) 41/2 (114.30) 31 (787.40) 25 (635.00) 1600 (7.12) 126.00 (57.15)
“B” (Center of axle to center of pipe)
(Fig. 475) With adjusting swivel
Available up to 8" (200)
Pipe Roller Size
(Fig. 475) Without adjusting swivel
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
ADJUSTABLE PIPE ROLLER SUPPORT FIG. 480 & 480D Function: Designed to support pipe in applications where horizontal movement, due to expansion and contraction,
will occur and a vertical adjustment of up to 6” (152.4) may be required. Fig. 480D is designed for
supporting and guiding pipe where longitudinal movement and
vertical adjustment are required.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with
insulation, refer to pipe roller selection guide, which is for use with
pipe covering protection saddles.
Material: Cast iron pipe roller and sockets with carbon steel rods, axles, and
hex nuts.
Finish: Plain or electro-
galvanized (Hot dipped
galvanized with electro-
galvanized hardware upon
request)
Approvals: Fig. 480 only, complies
with Federal Specification
A-A-1192A (Type 41)
and Manufacturers’
Standardization Society
ANSI/MSS SP-58 (Type
41) which supersedes
ANSI/MSS SP-69.
Ordering: Specify figure number,
pipe roller size, and
finish. Shipped with rods
and nuts unassembled.
Pipe Roller Size
Rod Size A
B C D E Max. Rec. Load
Wt. Each
480 480D
480 480D lbs. kN lbs. kg lbs. kg
2 (50) 3/8 15/8 (41.28) 27/8 (73.03) 41/2 (114.30) 71/4 (184.15) 12 (304.8) 600 (2.67) 1.25 (.57) 3.26 (1.48)
21/2 (65) 1/2 2 (50.80) 31/8 (79.38) 51/16 (128.59) 8 (203.20) 14 (355.6) 600 (2.67) 2.25 (1.02) 4.65 (2.11)
3 (80) 1/2 21/4 (57.15) 33/4 (95.25) 59/16 (141.29) 8 (203.20) 14 (355.6) 700 (3.11) 2.36 (1.07) 5.01 (2.27)
31/2 (90) 1/2 25/8 (66.68) 41/4 (107.95) 61/16 (153.99) 8 (203.20) 14 (355.6) 750 (3.34) 2.60 (1.18) 5.25 (2.38)
4 (100) 5/8 23/4 (69.85) 43/4 (120.65) 63/4 (171.45) 9 (228.60) 18 (457.2) 750 (3.34) 3.65 (1.66) 7.57 (3.43)
5 (125) 5/8 31/2 (88.90) 53/4 (146.05) 83/8 (212.73) 9 (228.60) 18 (457.2) 750 (3.34) 4.59 (2.08) 8.72 (3.96)
6 (150) 3/4 4 (101.60) 67/8 (174.63) 97/8 (250.83) 10 (254.00) 24 (609.6) 1070 (4.76) 7.50 (3.40) 16.87 (7.65)
8 (200) 7/8 51/8 (130.18) 87/8 (225.43) 12 (304.80) 10 (254.00) 24 (609.6) 1350 (6.01) 11.00 (4.99) 22.77 (10.33)
10 (250) 7/8 63/8 (161.93) 11 (279.40) 14 (355.60) 11 (279.40) 30 (762.0) 1730 (7.70) 13.68 (6.21) 28.30 (12.84)
12 (300) 7/8 71/2 (190.50) 13 (330.20) 161/2 (419.10) 11 (279.40) 30 (762.0) 2400 (10.68) 19.30 (8.75) 38.17 (17.31)
14 (350) 1 83/8 (212.73) 143/8 (365.13) 173/4 (450.85) 12 (304.80) 36 (914.4) 3130 (13.92) 31.20 (14.15) 64.13 (29.09)
16 (400) 1 91/2 (241.30) 163/8 (415.93) 203/4 (527.05) 18 (457.20) -- -- 3970 (17.66) 42.40 (19.23) -- --
18 (450) 1 101/2 (266.70) 183/8 (466.73) 223/8 (568.33) 18 (457.20) -- -- 4200 (18.68) 46.55 (21.11) -- --
20 (500) 11/4 115/8 (295.28) 203/8 (517.53) 241/2 (622.30) 18 (457.20) -- -- 4550 (20.24) 66.00 (29.94) -- --
24 (600) 11/2 14 (355.60) 243/8 (619.13) 2813/16 (731.84) 24 (609.60) -- -- 6160 (27.40) 102.50 (46.49) -- --
30 (750) 11/2 171/2 (444.50) 303/8 (771.53) 35 (889.00) 24 (609.60) -- -- 7290 (32.43) 186.80 (84.73) -- --
“B” (Center of axle to center of pipe)
(Fig. 480D) Double pipe roller
(Fig. 480) Single pipe roller
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
Function: Designed to support pipe in applications where horizontal movement, due
to expansion and contraction, will occur.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with insulation,
refer to pipe roller selection guide, which is for use with pipe covering
protection saddles. The two holes “G” on roller sizes 2”(50) through
6”(150) are located on the outside of the stand. The two holes “G” on
roller sizes 8”(200) through 42”(1050) are located on the inside of the
stand, under the pipe roller.
Material: Cast iron pipe roller with carbon steel
stand, axle, and hex nuts. (Type 304
or 316 Stainless Steel upon request)
Finish: Plain or electro-galvanized (Hot
dipped galvanized with electro-
galvanized hardware upon request)
Approvals: Complies with Federal Specification
A-A-1192A (Type 44) and
Manufacturers’ Standardization
Society ANSI/MSS SP-58 (Type 44)
which supersedes ANSI/MSS SP-69.
Ordering: Specify figure number, pipe roller
size, material, and finish.
2”(50) through 6”(150) 8”(200) through 42”(1050)
Pipe Roller Size B C D E F G Max. Rec. Load Wt. Each
lbs. kN lbs. kg
2 (50) 31/2 (88.90)
-- -- 6 (152.4) -- -- 13/4 (44.45) 1 (25.4) 390 (1.73) 4.48 (2.03) 21/2 (65) 37/8 (98.43)
3 (80) 41/8 (104.78)
31/2 (90) 43/8 (111.13)
4 (100) 413/16 (122.24)
-- -- 6 (152.4) -- -- 21/16 (52.39) 1 (25.4) 950 (4.23) 6.85 (3.11) 5 (125) 57/16 (138.11)
6 (150) 61/16 (153.99)
8 (200) 811/16 (220.66) 85/8 (219.08) 7 (177.8) 41/8 (104.78) 37/16 (87.31) 1 (25.4) 2100 (9.34) 14.09 (6.39)
10 (250) 913/16 (249.24)
12 (300) 113/8 (288.93) 107/8 (276.23) 8 (203.2) 513/16 (147.64) 37/8 (98.43) 1 (25.4) 3075 (13.68) 22.09 (10.02)
14 (350) 12 (304.80)
16 (400) 135/8 (346.08)
121/2 (317.50) 9 (228.6) 67/8 (174.63) 41/4 (107.95) 1 (25.4) 4980 (22.15) 32.00 (14.51) 18 (450) 145/8 (371.48)
20 (500) 155/8 (396.88)
24 (600) 173/4 (450.85) 131/2 (342.90) 9 (228.6) 75/8 (193.68) 43/8 (111.13) 1 (25.4) 6100 (27.13) 41.43 (18.79)
30 (750) 217/8 (555.63) 17 (431.80) 12 (304.8) 10 (254.00) 51/8 (130.18) 1 (25.4) 7500 (33.36) 80.00 (36.29)
36 (900) 253/4 (654.05) 20 (508.00) 12 (304.8) 12 (304.80) 53/4 (146.05) 1 (25.4) 12000 (53.38) 125.0 (56.70)
42 (1050) 287/8 (733.43)
FIG. 486 PIPE ROLLER STAND
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
ADJUSTABLE PIPE ROLLER STAND WITH BASE FIG. 487 Function: Designed to support pipe in applications where horizontal
movement, due to expansion and contraction, will occur and
vertical adjustment is required.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with
insulation, refer to pipe roller selection guide, which is for use
with pipe covering protection saddles.
Material: Cast iron pipe roller with carbon steel stand, axle, and adjusting
screws with locknuts. (Type 304 or 316 Stainless Steel upon
request)
Finish: Plain or electro-galvanized (Hot dipped galvanized with electro-
galvanized hardware upon request)
Approvals: Complies with Federal Specification
A-A-1192A (Type 46) and
Manufacturers’ Standardization Society
ANSI/MSS SP-58 (Type 46) which
supersedes ANSI/MSS SP-69.
Ordering: Specify figure number, pipe roller size,
material, and finish.
NOTE: Refer to Fig. 486 for measurements of
roller stand.
Pipe Roller Size
B C D E
Hole Size F
G Bolt Size
H
Max. Rec. Load Wt. Each
Min. Max. lbs. kN lbs. kg
2 (50) 51/8 (130.18) 53/8 (136.53)
37/8 (98.43) 7 (177.80) 51/2 (139.70) 1 (25.4) 1 (25.4) 5/8 390 (1.73) 12.03 (5.46) 21/2 (65) 53/8 (136.53) 55/8 (142.88)
3 (80) 53/4 (146.05) 6 (152.40)
31/2 (90) 6 (152.40) 61/4 (158.75)
4 (100) 61/2 (165.10) 7 (177.80)
51/8 (130.18) 83/8 (212.73) 6 (152.4) 1 (25.4) 1 (25.4) 5/8 950 (4.23) 15.24 (6.91) 5 (125) 7 (177.80) 71/2 (190.50)
6 (150) 75/8 (193.68) 81/8 (206.38)
8 (200) 103/8 (263.53) 115/8 (295.28) 73/8 (187.33) 103/4 (273.05) 7 (177.8) 1 (25.4) 11/8 (28.58) 3/4 2100 (9.34) 30.59 (13.88)
10 (250) 111/2 (292.10) 123/4 (323.85)
12 (300) 13 (330.20) 141/4 (361.95) 91/2 (241.30) 131/8 (333.38) 8 (203.20) 1 (25.4) 13/8 (34.93) 7/8 3075 (13.68) 44.96 (20.39)
14 (350) 135/8 (346.08) 147/8 (377.83)
16 (400) 151/4 (387.35) 165/8 (422.28)
111/8 (282.58) 141/2 (368.30) 9 (228.6) 1 (25.4) 13/8 (34.93) 1 4980 (22.15) 64.10 (29.08) 18 (450) 163/8 (415.93) 173/4 (450.85)
20 (500) 173/8 (441.33) 183/4 (476.25)
24 (600) 195/8 (498.48) 21 (533.40) 121/4 (311.15) 16 (406.40) 9 (228.6) 1 (25.4) 13/8 (34.93) 1 6100 (27.13) 76.68 (34.78)
30 (750) 24 (609.60) 263/4 (679.45) 153/4 (400.05) 191/4 (488.95) 12 (304.8) 1 (25.4) 15/8 (41.28) 11/4 7500 (33.36) 142.25 (64.52)
36 (900) 233/16 (588.96) 293/16 (741.36) 16 (406.40) 22 (558.80) 12 (304.8) 1 (25.4) 15/8 (41.28) 11/2 12000 (53.38) 156.23 (70.86)
42 (1050) 291/4 (742.95) 321/4 (819.15)
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
FIG. 488 FABRICATED ROLLER FOR LARGE PIPING Function: Designed to support pipe in applications where horizontal movement, due to expansion and contraction,
will occur.
Sizing: Pipe roller size shown for bare pipe.
Material: Carbon steel
Finish: Plain or electro-galvanized
Ordering: Specify figure number and finish.
Pipe Size
A B C D
Max. Rec. Load
Wt. Each E
lbs. kN lbs. kg
30 (750) 231/4 (590.55) 135/8 (346.08) 83/16 (207.96) 813/16 (223.84) 0 (0) 60000 (266.89) 142 (64.41)
36 (900) 26 (660.40) 135/8 (346.08) 83/16 (207.96) 915/16 (252.41) 1 (25.40) 60000 (266.89) 142 (64.41)
42 (1050) 2815/16 (735.01) 135/8 (346.08) 83/16 (207.96) 1015/16 (277.81) 2 (50.80) 60000 (266.89) 142 (64.41)
46 (1150) 307/8 (784.23) 135/8 (346.08) 83/16 (207.96) 117/16 (290.51) 27/16 (61.91) 60000 (266.89) 142 (64.41)
46 (1150) 311/8 (790.58) 161/4 (412.75) 1013/16 (274.64) 127/8 (327.03) 11/4 (31.75) 60000 (266.89) 186 (84.37)
48 (1200) 32 (812.80) 161/4 (412.75) 1013/16 (274.64) 131/4 (336.55) 111/16 (42.86) 60000 (266.89) 186 (84.37)
54 (1350) 347/8 (885.83) 161/4 (412.75) 1013/16 (274.64) 145/16 (363.54) 23/4 (69.85) 60000 (266.89) 186 (84.37)
60 (1500) 373/4 (958.85) 161/4 (412.75) 1013/16 (274.64) 157/8 (403.23) 315/16 (100.01) 60000 (266.89) 186 (84.37)
66 (1650) 409/16 (1030.29) 161/4 (412.75) 1013/16 (274.64) 161/2 (419.10) 5 (127.00) 60000 (266.89) 186 (84.37)
72 (1800) 433/8 (1101.73) 161/4 (412.75) 1013/16 (274.64) 175/8 (447.68) 61/16 (153.99) 60000 (266.89) 186 (84.37)
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
PIPE ROLLER WITH SOCKETS FIG. 490 Function: Designed to support pipe in applications where horizontal movement,
due to expansion and contraction, will occur.
Sizing: Pipe roller size shown is for bare pipe. For proper sizing with
insulation, refer to pipe roller selection guide, which is for use with
pipe covering protection saddles.
Material: Cast iron pipe roller and sockets with carbon steel axle.
Finish: Plain or electro-galvanized (Hot dipped galvanized with electro-
galvanized hardware upon request)
Approvals: Complies with Federal Specification A-A-1192A (Type 41) and
Manufacturers’ Standardization Society ANSI/MSS SP-58 (Type 41)
which supersedes ANSI/MSS SP-69.
Ordering: Specify figure number, pipe roller size, and finish.
Pipe Roller Size Rod
Size A B C D
Max. Rec. Load Wt. Each
lbs. kN lbs. kg
2 (50) 3/8 15/8 (41.28) 27/8 (73.03) 41/2 (114.30) 600 (2.67) .57 (.26)
21/2 (65) 1/2 2 (50.80) 31/8 (79.38) 51/16 (128.59) 660 (2.94) .98 (.44)
3 (80) 1/2 21/4 (57.15) 33/4 (95.25) 59/16 (141.29) 700 (3.11) 1.10 (.50)
31/2 (90) 1/2 25/8 (66.68) 41/4 (107.95) 61/16 (153.99) 750 (3.34) 1.36 (.62)
4 (100) 5/8 23/4 (69.85) 43/4 (120.65) 63/4 (171.45) 750 (3.34) 1.62 (.73)
5 (125) 5/8 31/2 (88.90) 53/4 (146.05) 83/8 (212.73) 750 (3.34) 2.60 (1.18)
6 (150) 3/4 4 (101.60) 67/8 (174.63) 97/8 (250.83) 1070 (4.76) 4.42 (2.00)
8 (200) 7/8 51/8 (130.18) 87/8 (225.43) 12 (304.80) 1350 (6.01) 7.20 (3.27)
10 (250) 7/8 63/8 (161.93) 11 (279.40) 14 (355.60) 1730 (7.70) 9.50 (4.31)
12 (300) 7/8 71/2 (190.50) 13 (330.20) 161/2 (419.10) 2400 (10.68) 16.00 (7.26)
14 (350) 1 83/8 (212.73) 143/8 (365.13) 173/4 (450.85) 3130 (13.92) 24.20 (10.98)
16 (400) 1 91/2 (241.30) 163/8 (415.93) 203/4 (527.05) 3970 (17.66) 31.80 (14.42)
18 (450) 1 101/2 (266.70) 183/8 (466.73) 223/8 (568.33) 4200 (18.68) 35.15 (15.94)
20 (500) 11/4 115/8 (295.28) 203/8 (517.53) 241/2 (622.30) 4550 (20.24) 47.00 (21.32)
24 (600) 11/2 14 (355.60) 243/8 (619.13) 2813/16 (731.84) 6160 (27.40) 76.20 (34.56)
30 (750) 11/2 171/2 (444.50) 303/8 (771.53) 35 (889.00) 7290 (32.43) 130.00 (58.97)
“B” (Center of axle to center of pipe)
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
FIG. 485 SHORT PIPE ROLLER Function: Designed for supporting pipe in applications where horizontal movement,
due to expansion and contraction, will occur.
Material: Cast iron (Type 304 or 316 Stainless Steel upon request)
Finish: Plain or electro-galvanized (Hot dipped galvanized upon request)
Ordering: Specify figure number, pipe roller size, material, and finish.
Pipe Roller Size
B C Hole Size
D E
Max. Rec. Load Wt. Each
lbs. kN lbs. kg
2 (50) 113/16 (46.04) 23/4 (69.85) 9/16 (14.29) 115/16 (49.21) 390 (1.73) 0.81 (0.37)
21/2 (65) 21/8 (53.98) 23/4 (69.85) 9/16 (14.29) 115/16 (49.21) 390 (1.73) 0.81 (0.37)
3 (80) 27/16 (61.91) 23/4 (69.85) 9/16 (14.29) 115/16 (49.21) 390 (1.73) 0.81 (0.37)
31/2 (90) 211/16 (68.26) 23/4 (69.85) 9/16 (14.29) 115/16 (49.21) 390 (1.73) 0.81 (0.37)
4 (100) 3 (76.20) 33/4 (95.25) 9/16 (14.29) 21/4 (57.15) 950 (4.23) 0.94 (0.42)
5 (125) 39/16 (90.49) 33/4 (95.25) 9/16 (14.29) 21/4 (57.15) 950 (4.23) 0.94 (0.42)
6 (150) 41/8 (104.78) 33/4 (95.25) 9/16 (14.29) 21/4 (57.15) 950 (4.23) 0.94 (0.42)
8 (200) 51/4 (133.35) 6 (152.40) 13/16 (20.64) 33/16 (80.96) 2100 (9.34) 3.19 (1.45)
10 (250) 63/8 (161.93) 6 (152.40) 13/16 (20.64) 33/16 (80.96) 2100 (9.34) 3.19 (1.45)
12 (300) 71/2 (190.50) 8 (203.20) 1 (25.40) 4 (101.60) 3075 (13.68) 6.64 (3.01)
14 (350) 83/16 (207.96) 8 (203.20) 1 (25.40) 4 (101.60) 3075 (13.68) 6.64 (3.01)
16 (400) 95/16 (236.54) 9 (228.60) 11/4 (31.75) 41/2 (114.30) 4980 (22.15) 8.31 (3.77)
18 (450) 103/8 (263.53) 9 (228.60) 11/4 (31.75) 41/2 (114.30) 4980 (22.15) 8.31 (3.77)
20 (500) 117/16 (290.51) 9 (228.60) 11/4 (31.75) 41/2 (114.30) 4980 (22.15) 8.31 (3.77)
24 (600) 137/16 (341.31) 10 (254.00) 11/2 (38.10) 43/8 (111.13) 6100 (27.13) 8.40 (3.81)
30 (750) 169/16 (420.69) 121/4 (311.15) 17/8 (47.63) 53/16 (131.76) 7500 (33.36) 14.40 (6.53)
36 (900) 1911/16 (500.06) 14 (355.60) 21/8 (53.98) 6 (152.40) 12000 (53.38) 16.80 (7.62)
42 (1050) 223/4 (577.85) 14 (355.60) 21/8 (53.98) 6 (152.40) 12000 (53.38) 16.80 (7.62)
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
LONG PIPE ROLLER FIG. 495 Function: Designed for supporting pipe in applications where horizontal movement,
due to expansion and contraction, will occur.
Material: Cast iron (Type 304 or 316 Stainless Steel upon request)
Finish: Plain or electro-galvanized (Hot dipped galvanized upon request)
Ordering: Specify figure number, pipe roller size, material, and finish.
Pipe Roller Size
B C Hole Size
D E
Max. Rec. Load Wt. Each
lbs. kN lbs. kg
2 (50) 15/8 (41.28) 27/8 (73.03) 7/16 (11.11) 13/16 (30.16) 600 (2.67) 0.22 (0.10)
21/2 (65) 2 (50.80) 31/8 (79.38) 9/16 (14.29) 17/16 (36.51) 700 (3.11) 0.33 (0.15)
3 (80) 21/4 (57.15) 33/4 (95.25) 9/16 (14.29) 11/2 (38.10) 700 (3.11) 0.43 (0.20)
31/2 (90) 25/8 (66.68) 41/4 (107.95) 9/16 (14.29) 15/8 (41.28) 750 (3.34) 0.53 (0.24)
4 (100) 23/4 (69.85) 43/4 (120.65) 9/16 (14.29) 2 (50.80) 750 (3.34) 0.56 (0.26)
5 (125) 31/2 (88.90) 53/4 (146.05) 11/16 (17.46) 21/8 (53.98) 750 (3.34) 0.94 (0.43)
6 (150) 4 (101.60) 67/8 (174.63) 13/16 (20.64) 27/16 (61.91) 1100 (4.89) 1.59 (0.72)
8 (200) 51/8 (130.18) 87/8 (225.43) 15/16 (23.81) 27/8 (73.03) 1350 (6.01) 2.64 (1.20)
10 (250) 63/8 (161.93) 11 (279.40) 15/16 (23.81) 31/2 (88.90) 1750 (7.78) 4.50 (2.04)
12 (300) 71/2 (190.50) 13 (330.20) 11/8 (28.58) 41/4 (107.95) 2400 (10.68) 7.55 (3.42)
14 (350) 83/8 (212.73) 143/8 (365.13) 11/4 (31.75) 45/8 (117.48) 3100 (13.79) 13.00 (5.90)
16 (400) 91/2 (241.30) 163/8 (415.93) 13/8 (34.93) 47/8 (123.83) 4000 (17.79) 17.44 (7.91)
18 (450) 101/2 (266.70) 183/8 (466.73) 13/8 (34.93) 55/16 (134.94) 4200 (18.68) 21.60 (9.80)
20 (500) 115/8 (295.28) 203/8 (517.53) 13/8 (34.93) 61/16 (153.99) 4550 (20.24) 27.13 (12.30)
24 (600) 14 (355.60) 143/8 (365.13) 15/8 (41.28) 71/16 (179.39) 6100 (27.13) 43.29 (19.63)
30 (750) 171/2 (444.50) 303/8 (771.53) 17/8 (47.63) 91/16 (230.19) 7300 (32.47) 82.00 (37.19)
Rod Size A
Use with Pipe Roller Size
Axle Size
B C D Wt. Each Socket
Number lbs. kg
1 3/8 2 3/8 5/8 (15.88) 1 (25.40) 11/16 (17.46) .12 (.05)
2 1/2 21/2 to 31/2 1/2 3/4 (19.05) 11/4 (31.75) 11/16 (17.46) .27 (.12)
2A 5/8 4 1/2 7/8 (22.23) 11/4 (31.75) 13/16 (20.64) .25 (.11)
3 5/8 5 5/8 1 (25.40) 19/16 (39.69) 1 (25.40) .53 (.24)
4 3/4 6 3/4 11/4 (31.75) 113/16 (46.04) 11/8 (28.58) .92 (.42)
5 7/8 8 to 10 7/8 11/4 (31.75) 21/8 (53.98) 11/8 (28.58) 1.44 (.65)
6 7/8 12 1 13/8 (34.93) 21/4 (57.15) 13/8 (34.93) 1.34 (.61)
7 1 14 11/8 13/4 (44.45) 23/8 (60.33) 13/8 (34.93) 2.03 (.92)
8 1 16 to 18 11/4 113/16 (46.04) 3 (76.20) 15/8 (41.28) 2.60 (1.18)
8A 11/4 20 11/4 113/16 (46.04) 3 (76.20) 15/8 (41.28) 2.56 (1.16)
9B 11/2 24 11/2 23/16 (55.56) 33/8 (85.73) 21/16 (52.39) 4.96 (2.25)
10 11/2 30 13/4 29/16 (65.09) 4 (101.60) 25/16 (58.74) 6.94 (3.15)
ROLLER SOCKET FIG. 496 Function: Designed for use with Fig. 495.
Material: Cast iron
Finish: Plain or electro-galvanized (Hot dipped galvanized upon request)
Ordering: Specify figure number, socket number, and finish.
Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters.
www.phd-mfg.com
For use with pipe covering protection saddle, figures 651-658 .
Pipe Thickness Insulation Thickness
Pipe Roller Size
Use with Fig. No.
460, 480, 483 & 490
470 & 475 486 & 487
1/2 (15)
1 (25.4) 2 21/2 2 - 31/2
11/2 (38.1) 3 31/2 2 - 31/2
2 (50.8) 4 5 2 - 31/2
3/4 (20)
1 (25.4) 2 21/2 2 - 31/2
11/2 (38.1) 3 31/2 2 - 31/2
2 (50.8) 4 5 2 - 31/2
1 (25)
1 (25.4) 21/2 3 2 - 31/2
11/2 (38.1) 3 4 2 - 31/2
2 (50.8) 4 5 2 - 31/2
11/4 (32)
1 (25.4) 21/2 3 2 - 31/2
11/2 (38.1) 31/2 5 2 - 31/2
2 (50.8) 4 5 2 - 31/2
21/2 (63.5) 5 6 4 - 6
11/2 (40)
1 (25.4) 3 31/2 2 - 31/2
11/2 (38.1) 31/2 5 2 - 31/2
2 (50.8) 5 6 4 - 6
21/2 (63.5) 6 8 4 - 6
2 (50)
1 (25.4) 31/2 4 2 - 31/2
11/2 (38.1) 4 5 2 - 31/2
2 (50.8) 5 6 4 - 6
21/2 (63.5) 6 8 4 - 6
3 (76.2) 8 8 4 - 6
4 (101.6) 8 10 8 - 10
21/2 (65)
1 (25.4) 31/2 5 2 - 31/2
11/2 (38.1) 5 6 4 - 6
2 (50.8) 6 8 4 - 6
21/2 (63.5) 8 8 4 - 6
3 (76.2) 8 10 4 - 6
4 (101.6) 8 10 8 - 10
3 (80)
1 (25.4) 4 5 2 - 31/2
11/2 (38.1) 5 6 4 - 6
2 (50.8) 6 8 4 - 6
21/2 (63.5) 8 8 4 - 6
3 (76.2) 8 10 8 - 10
4 (101.6) 8 12 8 - 10
31/2 (90)
1 (25.4) 5 6 4 - 6
11/2 (38.1) 6 8 4 - 6
2 (50.8) 8 8 4 - 6
21/2 (63.5) 8 10 8 - 10
3 (76.2) 10 10 8 - 10
4 (101.6) 10 12 8 - 10
4 (100)
1 (25.4) 5 6 4 - 6
11/2 (38.1) 6 8 4 - 6
2 (50.8) 8 8 4 - 6
21/2 (63.5) 8 10 8 - 10
3 (76.2) 10 10 8 - 10
4 (101.6) 10 12 8 - 10
5
1 (25.4) 6 8 4 - 6
(125)
11/2 (38.1) 8 8 4 - 6
2 (50.8) 8 10 8 - 10
21/2 (63.5) 10 10 8 - 10
3 (76.2) 10 12 8 - 10
4 (101.6) 12 14 8 - 10
Pipe Thickness Insulation Thickness
Pipe Roller Size
Use with Fig. No.
460, 480, 483 & 490
470 & 475 486 & 487
6 (150)
1 (25.4) 8 8 4 - 6
11/2 (38.1) 8 10 8 - 10
2 (50.8) 10 10 8 - 10
21/2 (63.5) 10 12 8 - 10
3 (76.2) 12 12 8 - 10
4 (101.6) 14 16 12 - 14
8 (200)
1 (25.4) 10 12 8 - 10
11/2 (38.1) 10 12 8 - 10
2 (50.8) 10 12 8 - 10
21/2 (63.5) 12 14 8 - 10
3 (76.2) 14 16 12 - 14
4 (101.6) 16 18 12 - 14
10 (250)
1 (25.4) 12 14 8 - 10
11/2 (38.1) 12 14 8 - 10
2 (50.8) 14 16 12 - 14
21/2 (63.5) 14 16 12 - 14
3 (76.2) 16 18 16 - 20
4 (101.6) 18 20 16 - 20
12 (300)
1 (25.4) 14 16 12 - 14
11/2 (38.1) 14 16 12 - 14
2 (50.8) 16 18 16 - 20
21/2 (63.5) 16 18 16 - 20
3 (76.2) 18 20 16 - 20
4 (101.6) 20 -- 16 - 20
14 (350)
11/2 (38.1) 16 18 12 - 14
2 (50.8) 16 18 16 - 20
21/2 (63.5) 18 20 16 - 20
3 (76.2) 18 20 16 - 20
4 (101.6) 20 -- 24
16 (400)
11/2 (38.1) 18 20 16 - 20
2 (50.8) 18 20 16 - 20
21/2 (63.5) 20 -- 16 - 20
3 (76.2) 20 -- 24
4 (101.6) 24 -- 24
18 (450)
11/2 (38.1) 20 -- 16 - 20
2 (50.8) 20 -- 24
21/2 (63.5) 24 -- 24
3 (76.2) 24 -- 24
4 (101.6) 24 -- 24
20 (500)
11/2 (38.1) 24 -- 24
2 (50.8) 24 -- 24
21/2 (63.5) 24 -- 24
3 (76.2) 24 -- 24
4 (101.6) 30 -- 30
24 (600)
11/2 (38.1) 30 -- 30
2 (50.8) 30 -- 30
21/2 (63.5) 30 -- 30
3 (76.2) 30 -- 30
4 (101.6) 30 -- 30
30
11/2 (38.1) -- -- 36-42
(750) 2 (50.8) -- -- 36-42
21/2 (63.5) -- -- 36-42
3 (76.2) -- -- 36-42
4 (101.6) -- -- 36-42
36 (900)
11/2 (38.1) -- -- 36-42
2 (50.8) -- -- 36-42
21/2 (63.5) -- -- 36-42
3 (76.2) -- -- 36-42
4 (101.6) -- -- 36-42
