Pioneer DEH 1330R,DeH 1300R,DeH 1310 Service Manual

PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A.PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936

C PIONEER CORPORATION 2000 K-ZZA. OCT. 2000 Printed in Japan

ORDER NO.

CRT2558

HIGH POWER CD PLAYER WITH RDS TUNER

DEH-1330R X1M/EW

ServiceManual

CONTENTS

1. SAFETY INFORMATION ............................................3

2. EXPLODED VIEWS AND PARTS LIST .......................4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...12

4. PCB CONNECTION DIAGRAM ................................34

5. ELECTRICAL PARTS LIST ........................................42

6. ADJUSTMENT..........................................................48

7. GENERAL INFORMATION .......................................52

7.1 DIAGNOSIS ........................................................52

7.1.1 TEST MODE..............................................52

7.1.2 DISASSEMBLY .........................................55

7.1.3 CONNECTOR FUNCTION DESCRIPTION.......59

7.2 PARTS .................................................................60

7.2.1 IC................................................................60

7.2.2 DISPLAY....................................................66

7.3 OPERATIONAL FLOW CHART...........................68

8. OPERATIONS AND SPECIFICATIONS.....................69

DEH-1300R X1M/EW

DEH-1310 X1M/EE

DEH-1330R/X1M/EW

- This service manual should be used together with the following manual(s):Model No. Order No. Mech. Module Remarks

CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly

2

DEH-1330R,1300R,1310

- CD Player Service Precautions

1. For pickup unit(CXX1285) handling, please refer

to"Disassembly"(see page 55).

During replacement, handling precautions shall be

taken to prevent an electrostatic discharge(protection

by a short pin).

2. During disassembly, be sure to turn the power off

since an internal IC might be destroyed when a con-

nector is plugged or unplugged.

3. Please checking the grating after changing the ser-

vice pickup unit(see page 50).

3

DEH-1330R,1300R,1310

1. SAFETY INFORMATION

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repaircomplex products such as those covered by this manual.Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do soand refer the repair to a qualified service technician.

1. Safety Precautions for those who Service this Unit.

• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable

results.

Caution:

1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.

2. During repair or tests, do not view laser beam for 10 seconds or longer.

2. A “CLASS 1 LASER PRODUCT” label is affixed to the

bottom of the player.

3. The triangular label is attached to the mechanism

unit frame.

4. Specifications of Laser Diode

Specifications of laser radiation fields to which human access is possible during service.Wavelength = 800 nanometers

CLASS 1LASER PRODUCT

4

DEH-1330R,1300R,1310

1 Cord Assy See Contrast table(2)2 Screw CBA10023 Handle CNC53954 Bush CNV3930

* 5 Polyethylene Bag E36-615

6 Polyethylene Bag CEG-1627-1 •••••7-2 Owner's Manual See Contrast table(2)7-3 Owner's Manual See Contrast table(2)7-4 Installation Manual See Contrast table(2)

* 7-5 Passport See Contrast table(2)* 7-6 Warranty Card CRY1157

8 Carton See Contrast table(2)9 Contain Box See Contrast table(2)

10 Protector CHP2346

11 Protector CHP234712 Case Assy CXB3520

Mark No. Description Part No. Mark No. Description Part No.

(1) PACKING SECTION PARTS LIST

NOTE:

- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.

- Screws adjacent to ∇ mark on the product are used for disassembly.

2. EXPLODED VIEWS AND PARTS LIST

2.1 PACKING

10

1

12

6

8

9

11

7

4

3

5

2

5

DEH-1330R,1300R,1310

Part No.Mark No. Symbol and Description DEH-1330R/X1M/EW DEH-1300R/X1M/EW DEH-1310/X1M/EE

1 Cord Assy CDE6467 CDE6467 CDE64707-2 Owner's Manual CRD3276 CRD3276 CRD32847-3 Owner's Manual CRD3277 CRD3277 Not used7-4 Installation Manual CRD3278 CRD3278 CRD3285

* 7-5 Passport CRY1013 CRY1013 Not used

8 Carton CHG4159 CHG4158 CHG41569 Contain Box CHL4159 CHL4158 CHL4156

(2) CONTRAST TABLE

DEH-1330R/X1M/EW, DEH-1300R/X1M/EW and DEH-1310/X1M/EE are constructed the same except for

the following:

- Owner's Manual, Installation ManualModel Part No. LanguageDEH-1330R/X1M/EW CRD3276 English, Spanish, GermanDEH-1300R/X1M/EW CRD3277 French, Italian, Dutch

CRD3278 English, Spanish, German, French, Italian, DutchDEH-1310/X1M/EE CRD3284 English, Russian

CRD3285 English, Russian

6

DEH-1330R,1300R,1310

2.2 EXTERIOR(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)

B

A

7

DEH-1330R,1300R,1310

1 •••••2 Screw BSZ26P060FMC3 Screw BSZ30P060FMC4 Screw BSZ30P120FMC5 Cable CDE6160

6 Cord Assy CDE64677 Cap CKX-0038 Fuse(10A) CEK11369 CD Mechanism Module(S8.1) CXK5203

10 Holder CNC5704

11 Cover CNC912712 Cushion CNM521013 Insulator CNM622414 Insulator CNM638615 Tuner Amp Unit CWM7294

16 Screw ASZ26P080FMC17 Screw BPZ26P080FMC18 Screw BSZ26P160FMC19 FM/AM Tuner Unit CWE156220 Holder CNC8815

21 Pin Jack(CN301) CKB104122 Terminal(CN403) CKF105923 Plug(CN901) CKM133024 Connector(CN601) CKS358125 Connector(CN605) CKS3838

26 Antenna Jack(CN402) CKX105627 Holder CNC804128 Holder CNC804329 Holder CNC912830 Heat Sink CNR1589

31 Case Unit CXB403332 Detach Grille Assy See Contrast table(2)33 Screw BPZ20P100FZK34 Button(DETACH) See Contrast table(2)35 Button(1-6, CLK) CAC6822

36 Button(A, B) CAC682337 Button(EJECT/BSM) CAC682438 Button(CROSS) CAC682539 Button(+/-, EQ, LD) CAC683440 Button(SOURCE) CAC6851

41 Spring CBH221042 Cover See Contrast table(2)43 Keyboard Unit See Contrast table(2)44 LCD CAW163245 Connector(CN1801) CKS3580

46 Holder CNC907847 Sheet CNM705748 •••••49 Lighting Conductor CNV647550 Lighting Conductor CNV6476

51 Rubber CNV647752 Rubber CNV647853 Grille Unit See Contrast table(2)54 Chassis Unit See Contrast table(2)55 Holder Unit CXB6681

56 Button CAC483657 Spring CBH183558 Spring CBH220859 Spring CBH236760 Bracket CNC6791

61 Holder CNC804262 Cover CNM627663 Panel See Contrast table(2)64 Arm CNV469265 Arm CNV4728

66 Arm CNV557667 Screw IMS20P030FZK68 Screw ISS26P055FUC69 IC(IC302) TDA738670 Transistor(Q904, 981) 2SD2396

(1) EXTERIOR SECTION PARTS LIST


Part No.Mark No. Symbol and Description DEH-1330R/X1M/EW DEH-1300R/X1M/EW

32 Detach Grille Assy CXB6148 CXB614734 Button(DETACH) CAC5929 CAC578942 Cover CNS6383 CNS611443 Keyboard Unit CWM7306 CWM730553 Grille Unit CXB7184 CXB7183

54 Chassis Unit CXB6658 CXB665763 Panel CNS6385 CNS6345

(2) CONTRAST TABLE

DEH-1330R/X1M/EW and DEH-1300R/X1M/EW are constructed the same except for the following:

8

DEH-1330R,1300R,1310

2.3 EXTERIOR(DEH-1310/X1M/EE)

B

A

9

DEH-1330R,1300R,1310

1 •••••2 Screw BSZ26P060FMC3 Screw BSZ30P060FMC4 Screw BSZ30P120FMC5 Cable CDE6160

6 Cord Assy CDE64707 Fuse(10A) CEK11368 CD Mechanism Module(S8.1) CXK52039 Holder CNC5704

10 Cover CNC9127

11 Cushion CNM521012 Insulator CNM622413 Insulator CNM638614 Tuner Amp Unit CWM729515 Screw ASZ26P080FMC

16 Screw BPZ26P080FMC17 Screw BSZ26P160FMC18 FM/AM Tuner Unit CWE156619 Holder CNC881520 Pin Jack(CN301) CKB1041

21 Terminal(CN403) CKF105922 Plug(CN901) CKM133023 Connector(CN601) CKS358124 Connector(CN605) CKS383825 Antenna Jack(CN402) CKX1056

26 Holder CNC804127 Holder CNC804328 Holder CNC912829 Heat Sink CNR158930 Case Unit CXB4033

31 Chassis Unit CXB462532 Detach Grille Assy CXB614933 Screw BPZ20P100FZK34 Button(DETACH) CAC578935 Button(+/-, EQ, LD) CAC6821

36 Button(1-6, CLK) CAC682237 Button(A, B) CAC682338 Button(EJECT/BSM) CAC682439 Button(CROSS) CAC682540 Button(SOURCE) CAC6851

41 Spring CBH221042 Cover CNS611443 Keyboard Unit CWM730744 LCD CAW163345 Connector(CN1801) CKS3580

46 Holder CNC907847 Sheet CNM705748 Lighting Conductor CNV647549 Lighting Conductor CNV647650 Rubber CNV6477

51 Rubber CNV647852 Grille Unit CXB718553 Holder Unit CXB668154 Button CAC483655 Spring CBH1835

56 Spring CBH220857 Spring CBH236758 Bracket CNC679159 Holder CNC804260 Cover CNM6276

61 Panel CNS634562 Arm CNV469263 Arm CNV472864 Arm CNV557665 Screw IMS20P030FZK

66 Screw ISS26P055FUC67 IC(IC302) TDA738668 Transistor(Q904, 981) 2SD2396

- EXTERIOR SECTION PARTS LIST


10

DEH-1330R,1300R,1310

2.4 CD MECHANISM MODULE

C

D

11

DEH-1330R,1300R,1310


1 Control Unit CWX24112 Connector(CN802) CKS21923 Connector(CN801) CKS21934 Connector(CN701) CKS27735 Connector(CN101) CKS3486

6 Screw BMZ20P030FMC7 Screw BSZ20P040FMC8 Screw(M2x3) CBA10779 Screw(M2x5) EBA1028

10 Screw CBA1243

11 Screw(M2x4) CBA136212 Washer CBF103713 Washer CBF103814 Washer CBF106015 •••••

16 Spring CBH207917 Spring CBH211718 Spring CBH231419 Spring CBH211020 Spring CBH2282

21 Spring CBH231822 •••••23 Spring CBH232424 Spring CBH211825 Spring CBH2161

26 Spring CBH216327 Spring CBH218928 Spring CBH237729 Spring CBH226030 Spring CBH2262

31 Bracket CNC856832 Spring CBL136933 Connector CDE553134 Connector CDE553235 Shaft CLA3894

36 Screw(M2.6x6) CBA145837 Frame CNC856538 Frame CNC874939 Lever CNC926540 Arm CNC8663

41 Bracket CNC856742 •••••43 Spacer CNM331544 Sheet CNM665945 •••••

46 •••••47 Ball CNR118948 Belt CNT108649 Roller CNV450950 Arm CNV6037

51 Arm CNV524752 Arm CNV524853 Arm CNV524954 Guide CNV525455 Guide CNV5255

56 Gear CNV525757 Gear CNV525658 Guide CNV627259 Damper CNV617460 Arm CNV6096

61 Arm CNV603162 Arm CNV621163 Guide CNV601264 Guide CNV551065 •••••

66 Guide CNV575167 Clamper CNV601368 Gear CNV581369 Motor Unit(M1) CXB219070 Screw Unit CXB5892

71 Chassis Unit CXB479772 Gear Unit CXB472873 Arm Unit CXB575374 Motor Unit(M2) CXB219575 Lever Unit CXB4730

76 Arm Unit CXB473177 Motor Unit(M3) CXB256278 Arm Unit CXB473279 Bracket Unit CXB479580 Screw JFZ20P025FMC

81 Screw JGZ17P025FZK82 Washer YE20FUC83 Pickup Unit(Service)(P8) CXX128584 Screw IMS26P030FMC

* 85 PCB CNX2982

86 Photo-transistor(Q1, 2) CPT230SX-TU87 Damper CNV617588 Rack CNV601489 Spring CBH2315

- CD MECHANISM MODULE SECTION PARTS LIST

12

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM

M

M

M

LDMD

HOLOGRAMUNIT

FOCUS ACTTRACKING ACT

LD+

MD

FO+

TO+

14

5

4

3

SPINDLEMOTOR

CARRIAGEMOTOR

LOADINGMOTOR

1

2

3

4

3

1

2

SELECTSENSE

DISC SENSE

D

CN801

CN802

D802 D801

VD

S802CLAMP

6

5

11

22

23

21

1

28

21

CDLOAD

CDEJET

CONT

EJTSNS

DSCSNS

CLAMP

CD5VON

VDCONT

VDD IC 701BA05SFP

IN

+5V REGULATOR

24

1

VD

Q981

Q982

B.U

ANTENNA CN402

A

LOCL

Q411

VCC VDD

PC

E2

PC

K

PC

E1

SL

SD

PD

IO

C

Q101CN101

FOP

TOP

A+C/F

B+D/E

98LD L_OUT

PD

HOME

97

24

23

39

X201

TD/FD

SD/MD

RF-AMP, DSP,SERVO, DAC

IC 201UPD63711GC

16CN701 CN605

17

1

8

24

CDL

IC 301BA5985FM

S801HOME12

16

18

11

14

13

10

9

SOP

TOP

FOP

SOM

COP

COM

LOP

LOM

FWD

REV

MUTE

CD

DR

IVE

R

7 18

19

20

14

3

2

4

CLAMP

DINC

EJTD

CDLOAD

EJET

CONT

PDIO

TUNER AMP UNIT

CONTROL UNITPICKUP UNIT(SERVICE)(P8)

PHOTO UNIT(S8)

4

VD

CD5VON

IC 3EEPROM

FM/AM TUNER UNIT

28

27

FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53

IC1MIXER, IF AMP, DET.

6

21

18LDET

COMP

2225 10 14 12 15 16 8 13 2 3 4

CF202

VDDVCC

DI/D

O

CE

2

CK

CE

1

SD

BW

SL

FMS

D

NL1

NL2

IC 2 FM MPX

AMANT

FMANT

ATT

ATT

AMRF

FMRF

IMG ADJ

RF ADJ

X90110.25MHz

ANT ADJ

LOCL23

LOCH

AMDETMPXREF 41kHz

AM 2ND IF450kHz

19

CR

EQ

11

DG

ND

1

ST

IND

L ch

5R ch

924

NC

FMLO

CL

20177

NC

NC

WC

26 RFGND

Q472 Q475 Q476

RDSDECODER

IC 701PM4009A

20

11 12

X702

Q477

VDD

TMUTE

FM/AM

LDET

13

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

KYDT

DPDT

KEY CONT. LCD DRIVER

IC 1801PD6340A

3

4

5

3

4

5

KEY MATRIX

SD

SL

PCE

PCK

TUNPCE2

PDO

LOCL

IN2_L

IN3_L

6

76

14

13

48

12

57

2

3

SYSTEMCONTROLLER

IC 601(1/2)PE5195A

VSTVCKVDT

B.UVDD

Q903B.U

BACKUP

FL—

FL+

RL—

RL+

ACC

2

1

9

11

10

12

4

E.VOLFIE/EQ

IC 301PML003AM

SYSTEMCONTROLLER

IC 601(2/2)PE5195A

ASENS63

BSENS64

CELLMUTE32

SYSPW42

MUTE44

KYDT8

DPDT9

RESET60

SWVDD41

Frontout_L10

Rearout_L11

POWER AMP

IC 302TDA7386

14

12

22 4

5

3

21

23

FL

MUTE STBY

RL

B.Ubsens

asens

Q902Q351 MUTEQ350

B KEYBOARD UNIT

CN1801CN601

LCD

22 23

X1801

20

18

Q650

RESETIC 602

S—80834ANY VDD1 2

SY

SP

W

GND

B.U

SYSPW

5B.REM

FUSE10A

CD5VON

31

34

23

80

79

27

22

35

VDCONT

CLAMP

DSCSNS

EJTSNS

CDLOAD

CDEJET

CONT

PDI11PDIO

VST/ VCK/ VDT

Q901

VDD

VDD

VLCD

56

10

CN901

IC970TPD1018F

POWER SWITCH

5

6

1

Q346

CN301

REAR L CH

Q363

RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

BACKUP

BACK UP

FL–

FL+

RL–

RL+

B.REM

ACC

GND

B.REM

CELLULARMUTE

7TELIN

Q951

CELLULAR MUTE

TELIN

66

61

21FM/AM

LDET

TMUTE

14

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS

LIST”.

A-a A-b

A-aA-a A-b A-b

A-b A-b A-a A-a

Large sizeSCH diagram

Guide page

Detailed page

A

DS

P-2

01M

-S00

B

123

272

272

123

162

162

473

4.194MHz

PE5195A

CN601

CN403

CN402

FM(100%):-15.5dBsAM(30%):-26dBs

SYSTEM CONTROLLER

For resistors and capacitors in the circuit diagrams, their resistance values orcapacitance values are expressed in codes:

Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms

*Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V

The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.

Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.

NOTE :

Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.

KEYBOARDUNIT

B

FM/AM TUNER UNIT

A-aTUNER AMP UNITA

15

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A

332/

16

NC

TD

A73

86

600µH

331/

16

CN901

CN301

CN605

CEK1136

>

FM(100%):+6.6dBsAM(30%):-2.9dBsCD:+10.2dBs

FM(100%):+32.6dBsAM(30%):+23.1dBsCD:+36.2dBs

CD:+4.1dBs

CD:+9.4dBs

RESET

E.VOLFIE/EQ

POWER AMP

A.SENS

B.SENS

CO

NT

RO

L U

NIT

C RR+

RR-

FR+

FR-

FL+

FL-

RL+

RL-ACCGND

B.REM

BACKUP

A-b

16

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

A-a

A-a

A-b

1

DSP-201M-S00B

123

272272

123

162

162

CN

403

CN

402

FM(1

00%

):-1

5.5d

Bs

AM

(30%

):-2

6dB

s

FM/A

M T

UN

ER

UN

IT

TU

NE

R A

MP

UN

ITA

17

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A-a

A-a

A-b

473

4.19

4MH

z

PE

5195

A

CN

601

SY

ST

EM

CO

NT

RO

LLE

R

RE

SE

For

resi

sto

rs a

nd

cap

acit

ors

in t

he

circ

uit

dia

gra

ms,

th

eir

resi

stan

ce v

alu

es o

rca

pac

itan

ce v

alu

es a

re e

xpre

ssed

in c

od

es:

Ex.

*R

esis

tors

C

od

e

P

ract

ical

val

ue

1

23

12k

oh

ms

1

03

10k

oh

ms

*C

apac

ito

rs

Co

de

P

ract

ical

val

ue

1

03

0.01

µF

101

/10

10

0µF/

10V

Th

e >

mar

k fo

un

d o

n s

om

e co

mp

on

ent

par

ts in

dic

ates

the

imp

ort

ance

of

the

safe

ty f

acto

r o

f th

e p

art.

Th

eref

ore

, wh

en r

epla

cin

g, b

e su

re t

o u

se p

arts

of

iden

tica

l des

ign

atio

n.

Sym

bo

l in

dic

ates

a r

esis

tor.

No

dif

fere

nti

atio

n is

mad

e b

etw

een

ch

ip r

esis

tors

an

dd

iscr

ete

resi

sto

rs.

NO

TE

: Sym

bo

l in

dic

ates

a c

apac

ito

r.N

o d

iffe

ren

tiat

ion

is m

ade

bet

wee

n c

hip

cap

acit

ors

an

dd

iscr

ete

cap

acit

ors

.

KE

YB

OA

RD

UN

IT

B

CONTROL UNIT C

2

18

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

A-a

A-b

A-b

332/16

NC

TDA7386

600µ

H

CN

901

CN

301

CE

K11

36

>

FM(1

00%

):+6

.6d

Bs

AM

(30%

):-2

.9d

Bs

CD

:+10

.2d

Bs

FM(1

00%

):+3

2.6d

Bs

AM

(30%

):+2

3.1d

Bs

CD

:+36

.2d

Bs

CD

:+9.

4dB

s

E.V

OL

FIE

/EQ

PO

WE

R A

MP

1

19

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A-b

A-a

A-b

600µ

H

331/16

CN

605

CE

K11

36

CD

:+4.

1dB

s

RE

SE

T

A.S

EN

S

B.S

EN

S

CONTROL UNIT C

RR +RR -

FR +FR -

FL +FL -

RL +RL -

ACC

GN

D

B. REM

BACK

UP

2

20

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

3.3 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)(DEH-1310/X1M/EE)

A

DS

P-2

01M

-S00

B

123

272

272

123

162

162

363

153

PE5196A

CN601

CN403

CN402

FM(100%):-15.5dBsAM(30%):-26dBs

SYSTEM CONTROLLER

For resistors and capacitors in the circuit diagrams, their resistance values orcapacitance values are expressed in codes:

Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms

*Capacitors Code Practical value 103 0.01µF 101/10 100µF/10V

The > mark found on some component parts indicatesthe importance of the safety factor of the part.Therefore, when replacing, be sure to use parts ofidentical designation.

Symbol indicates a resistor.No differentiation is made between chip resistors anddiscrete resistors.

NOTE :

Symbol indicates a capacitor.No differentiation is made between chip capacitors anddiscrete capacitors.

KEYBOARDUNIT

B

FM/AM TUNER UNIT

A-aTUNER AMP UNITA

21

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A

332/

16

NC

TD

A73

86

600µH

331/

16

CN901

CN301

CN605

CEK1136

>

FM(100%):+6.6dBsAM(30%):-2.9dBsCD:+10.2dBs

FM(100%):+32.6dBsAM(30%):+23.1dBsCD:+36.2dBs

CD:+4.1dBs

CD:+9.4dBs

RESET

E.VOLFIE/EQ

POWER AMP

A.SENS

B.SENS

CO

NT

RO

L U

NIT

C

A-b

22

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

A-a

A-a

A-b

1

DSP-201M-S00B

123

272272

123

162

162

CN

403

CN

402

FM(1

00%

):-1

5.5d

Bs

AM

(30%

):-2

6dB

s

FM/A

M T

UN

ER

UN

IT

TU

NE

R A

MP

UN

ITA

23

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A-a

A-a

A-b

363153

PE

5196

A

CN

601

SY

ST

EM

CO

NT

RO

LLE

R

RE

SE

For

resi

sto

rs a

nd

cap

acit

ors

in t

he

circ

uit

dia

gra

ms,

th

eir

resi

stan

ce v

alu

es o

rca

pac

itan

ce v

alu

es a

re e

xpre

ssed

in c

od

es:

Ex.

*R

esis

tors

C

od

e

P

ract

ical

val

ue

1

23

12k

oh

ms

1

03

10k

oh

ms

*C

apac

ito

rs

Co

de

P

ract

ical

val

ue

1

03

0.01

µF

101

/10

10

0µF/

10V

Th

e >

mar

k fo

un

d o

n s

om

e co

mp

on

ent

par

ts in

dic

ates

the

imp

ort

ance

of

the

safe

ty f

acto

r o

f th

e p

art.

Th

eref

ore

, wh

en r

epla

cin

g, b

e su

re t

o u

se p

arts

of

iden

tica

l des

ign

atio

n.

Sym

bo

l in

dic

ates

a r

esis

tor.

No

dif

fere

nti

atio

n is

mad

e b

etw

een

ch

ip r

esis

tors

an

dd

iscr

ete

resi

sto

rs.

NO

TE

: Sym

bo

l in

dic

ates

a c

apac

ito

r.N

o d

iffe

ren

tiat

ion

is m

ade

bet

wee

n c

hip

cap

acit

ors

an

dd

iscr

ete

cap

acit

ors

.

KE

YB

OA

RD

UN

IT

B

CONTROL UNIT C

2

24

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

A-a

A-b

A-b

332/16

NC

TDA7386

600µ

H

CN

901

CN

301

CE

K11

36

>

FM(1

00%

):+6

.6d

Bs

AM

(30%

):-2

.9d

Bs

CD

:+10

.2d

Bs

FM(1

00%

):+3

2.6d

Bs

AM

(30%

):+2

3.1d

Bs

CD

:+36

.2d

Bs

CD

:+9.

4dB

s

E.V

OL

FIE

/EQ

PO

WE

R A

MP

1

25

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A-b

A-a

A-b

600µ

H

331/16

CN

605

CE

K11

36

CD

:+4.

1dB

s

RE

SE

T

A.S

EN

S

B.S

EN

S

CONTROL UNIT C

2

26

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

3.4 KEYBOARD UNIT

KEYBOARD UNIT

LCD CAW1605

LCD DRIVERKEY CONTROLLER

B

B

27

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

ACN601IL1801, 1802:CEL1638(14V 40mA)

(DEH-1330R/X1M/EW)IL1801, 1802:CEL1651(14V 40mA)(DEH-1300R/X1M/EW)(DEH-1310/X1M/EE)

D17

01-1

708:

SM

L210

DT

(DE

H-1

330R

/X1M

/EW

)

R17

08, 1

710,

171

2:18

1(D

EH

-133

0R/X

1M/E

W)

R17

08, 1

710,

171

2:15

1(D

EH

-130

0R/X

1M/E

W)

(DE

H-1

310/

X1M

/EE

)

D17

01-1

708:

SM

L210

PT

(DE

H-1

300R

/X1M

/EW

)(D

EH

-131

0/X

1M/E

E)

PTY

BSM

EQ

TA

B

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

BA05SFP

(SERVICE)(P8)PICKUP UNIT

PHOTO UNIT(S8)

CONTROL UNIT

SPINDLE MOTOR

Q2 CPT230SX-TUQ1 CPT230SX-TU

M3 CXB2562

CARRIAGE MOTOR

M1 CXB2190

M2 CXB2195

LOADING MOTOR

RF-AMP, SE

5V REGULATOR

CD DRIVER

CN101

CN802

CN801

CL203IRXTU CL203IRXTU


D

D

C

28 C

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

MP, SERVO, DSP, DAC, LPF

SWITCHES:CONTROL UNIT S801 : HOME SWITCH.....ON-OFF S802 : CLAMP SWITCH....ON-OFFThe underlined indicates the switch position.

CN701

CN

605

A

29C

30

DEH-1330R,1300R,1310

1 RFI 0.5V/div. 0.5µs/div.Normal mode: play

1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Test mode: Tracking open

0.5ms/div. 1 CH1: RFI 1V/div.2 CH2: MIRR 5V/div.

Normal mode: The defect partpasses 800µm

0.5ms/div.

3 CH1: FD 0.5V/div.4 CH2: FO+ 2V/div.

Test mode: No disc, Focus close

0.2s/div. 3 CH1: FD 0.5V/div.5 CH2: FOK 2V/div.

Normal mode: Focus close

0.2s/div. 6 CH1: FE 0.5V/div.7 CH2: XSI 2V/div.

Normal mode: Focus close

1ms/div.

REFO →

8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 32 tracks jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: Single jump (FWD)

0.5ms/div. 8 CH1: TE 0.5V/div.9 CH2: TD 0.5V/div.

Test mode: 100 tracks jump (FWD)

5ms/div.

6 CH1: FE 0.1V/div.3 CH2: FD 0.2V/div.

Normal mode: Play

20ms/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (12cm)

0.5s/div. 3 CH1: FD 0.5V/div.0 CH2: MD 1V/div.

Normal mode: Focus close (8cm)

0.5s/div.

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

GND →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

- Waveforms

Note:1. The encircled numbers denote measuring pointes in the circuit diagram.2. Reference voltage

REFO:2.5V

REFO →

REFO →

REFO →

REFO →

31

DEH-1330R,1300R,1310

8 CH1: TE 0.2V/div.9 CH2: TD 0.2V/div.

Normal mode: play

8 CH1: TE 0.5V/div.! CH2: SD 0.5V/div.TEST mode: 100 Tracks jump(FWD)

5ms/div. 0 MD 0.5V/div. 0.1s/div.

Normal mode: Play (12cm)

0 MD 1V/div. 10ms/div.Normal mode:Long Search (12cm)

@ EFM 1V/div. 5µs/div.

Normal mode: play

8 CH1: TE 1V/div.# CH2: TEC 1V/div.

Test mode: Focus closeTracking open

2ms/div.

8 CH1: TE 0.5V/div.6 CH2: FE 0.5V/div.

Normal mode: AGC after focus close

0.2s/div.$ PLCK 2V/div. 0.5µs/div.

Normal mode: play

20ms/div.

% SCKO 2V/div. 1µs/div.

Normal mode: play

^ Dout 2V/div. 10µs/div.

Normal mode: play

& LRCK 2V/div. 20µs/div.

Normal mode: play

* VD 5V/div. 50ms/div.

Normal mode: No disc

GND →

REFO →

REFO →

GND →

REFO →

REFO →

REFO →

REFO →REFO →

REFO →

REFO →

REFO →

REFO →

GND →

REFO →

GND →

REFO →

GND →

REFO →

GND →

REFO →

32

DEH-1330R,1300R,1310

( CH1: R OUT 1V/div.) CH2: L OUT 1V/div.

Normal mode: Play (1kHz 0dB)

6 CH1: FE 0.2V/div.3 CH2: FD 0.5V/div.

Normal mode: During AGC

1ms/div. 8 CH1: TE 0.2V/div.9 CH2: TD 0.5V/div.

Normal mode: During AGC

1 CH1: RFI 1V/div.⁄ CH2: HOLD 5V/div.

Normal mode: The defect part passes800µm(B.D)

0.2ms/div. 1ms/div.

0.5ms/div. 3 CH1: FD 0.5V/div.⁄ CH2: HOLD 5V/div.


0.5ms/div.9 CH1: TD 0.1V/div.⁄ CH2: HOLD 5V/div.


0.5ms/div.

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO →

REFO → REFO →

REFO →

REFO →

REFO →

33

DEH-1330R,1300R,1310

34

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

NOTE FOR PCB DIAGRAMS

1. The parts mounted on this PCB

include all necessary parts for

several destination.

For further information for

respective destinations, be

sure to check with the

schematic diagram.

2. Viewpoint of PCB diagrams

A

CapacitorConnector

P.C.Board Chip Part

SIDE A

SIDE B

1 3 5 7 9 11 13 15

2

4 6 8 10 12 14 16

CN1801BCN701C

CORD ASSY

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP UNIT

A TUNER AMP UNIT

35

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

AFRONT

1

2

3

1 2

FM/A

M T

UN

ER

UN

IT

SIDE A

ANTENNA PRE OUT

36

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

A

456

321

123

654

A TUNER AMP UNIT

37

DEH-1330R,1300R,13105 6 7 8

5 6 7 8

D

C

B

A

A

123

654

456

321

FRONT

SIDE B

38

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

TA

VO

L-

VO

L-S

OU

RC

E SO

UR

CE

12

34

56

PT

Y

BS

ME

JEC

T

BANDAUDIO

←→

↑ ↓

VO

L+

VO

L+E

Q

4.2 KEYBOARD UNIT SIDE A

KE

YB

OA

RD

UN

IT

B

B

39

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

B

B

CN

601

A

SIDE B

KE

YB

OA

RD

UN

IT

40

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A


CO

NT

RO

L U

NIT

HO

ME

M1

CA

RR

IAG

E M

OT

OR

M2

LOA

DIN

G M

OT

OR

M3

SP

IND

LE M

OT

OR

PIC

KU

P U

NIT

(SE

RV

ICE

)(P

8)

CN

802

CN

605

3 2 1

PH

OT

O U

NIT

(S8)

SIDE A

D

D

C

C

C

D

A

41

DEH-1330R,1300R,13101 2 3 4

1 2 3 4

D

C

B

A

CLA

MP

SIDE B

CO

NT

RO

L U

NIT

C

C

42

DEH-1330R,1300R,1310

5. ELECTRICAL PARTS LIST

NOTES:

- Parts whose parts numbers are omitted are subject to being not supplied.

- The part numbers shown below indicate chip components.

Chip Resistor

RS1/_S___J,RS1/__S___J

Chip Capacitor (except for CQS.....)

CKS....., CCS....., CSZS.....

=====Circuit Symbol and No.===Part Name Part No.--- ------ ------------------------------------------ -------------------------

Unit Number : CWM7294(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)Unit Name : Tuner Amp Unit

MISCELLANEOUS

IC 301 IC PML003AMIC 302 IC TDA7386IC 601 IC PE5195AIC 602 IC S-80834ANYIC 701 IC PM4009A

IC 970 IC TPD1018FQ 346 Transistor RN1610Q 350 Transistor DTA124EKQ 351 Transistor DTC114EKQ 353 Transistor DTA124EK

Q 411 Transistor 2SC2412KQ 412 Transistor 2SC2412KQ 472 Transistor RN1610Q 474 Transistor 2SD1757KQ 475 Transistor 2SD1757K

Q 476 Transistor 2SC2412KQ 477 Transistor DTA124EKQ 650 Transistor 2SA1037KQ 901 Transistor 2SC2412KQ 902 Transistor 2SC2412K

Q 903 Transistor 2SD1859Q 904 Transistor 2SD2396Q 905 Transistor 2SB1243Q 906 Transistor DTC114EKQ 920 Transistor RN46A1

Q 951 Transistor 2SA1037KQ 981 Transistor 2SD2396Q 982 Transistor RN46A1D 650 Diode 1SS270D 651 Diode 1SS270

D 652 Diode 1SS270D 653 Diode 1SS270D 654 Diode 1SS270D 655 Diode 1SS270D 901 Diode HZS7L(C2)

D 902 Diode S5688GD 903 Diode S5688GD 904 Diode HZS7L(A1)D 905 Diode S5688GD 906 Diode HZS6L(B2)

D 907 Diode HZS9L(B3)D 941 Diode S5688GD 942 Diode S5688GD 951 Diode 1SS270D 952 Diode 1SS270

D 981 Diode HZS9L(B1)L 310 Ferri-Inductor LAU1R0ML 401 Ferri-Inductor LAU4R7KL 402 Ferri-Inductor LAU2R2KL 403 Inductor LAU100K

L 610 Ferri-Inductor LAU101KL 611 Ferri-Inductor LAU2R2KL 650 Ferri-Inductor LAU2R2KL 703 Inductor LAU100KL 704 Ferri-Inductor LAU101K

L 901 Choke Coil 600µH CTH1221L 951 Ferri-Inductor LAU2R2KX 610 Ceramic Resonator 4.194MHz CSS1047X 702 Crystal Resonator 3.648MHz CSS1447EF 701 Filter CTF1071

AR 946 Arrester DSP-201M-S00BFM/AM Tuner Unit CWE1562

RESISTORS

R 310 RD1/4PU222JR 311 RD1/4PU222JR 330 RD1/4PU472JR 331 RS1/16S472JR 332 RS1/16S221J

R 333 RS1/16S221JR 334 RS1/16S221JR 335 RS1/16S221JR 342 RS1/16S681JR 343 RS1/16S681J

R 344 RS1/16S223JR 345 RS1/16S223JR 346 RS1/16S0R0JR 351 RS1/16S102JR 352 RS1/16S103J

R 353 RS1/16S103JR 354 RS1/16S331JR 360 RD1/4PU153JR 411 RS1/16S681JR 412 RS1/16S681J

R 413 RS1/16S681JR 414 RS1/16S103JR 415 RS1/16S681JR 416 RD1/4PU473JR 417 RD1/4PU472J




A

43

DEH-1330R,1300R,1310



R 447 RS1/16S0R0JR 460 RS1/16S162JR 461 RS1/16S162JR 464 RS1/16S272JR 465 RS1/16S272J


R 479 RD1/4PU224JR 611 RS1/16S473JR 619 RS1/16S0R0JR 620 RS1/16S223JR 622 RD1/4PU222J

R 623 RD1/4PU222JR 624 RS1/16S473JR 625 RS1/16S473JR 626 RS1/16S473JR 627 RS1/16S473J

R 628 RD1/4PU222JR 630 RS1/16S822JR 631 RD1/4PU102JR 649 RS1/16S222JR 650 RD1/4PU222J

R 651 RD1/4PU222JR 652 RS1/16S472JR 653 RD1/4PU222JR 654 RS1/16S473JR 655 RS1/16S103J

R 656 RS1/16S103JR 657 RD1/4PU102JR 658 RD1/4PU102JR 660 RS1/16S1R0JR 681 RD1/4PU681J

R 682 RS1/16S102JR 683 RS1/16S102JR 684 RS1/16S102JR 713 RS1/16S225JR 717 RD1/4PU102J


R 902 RD1/4PU104JR 903 RD1/4PU103JR 904 RS1/16S473JR 905 RD1/4PU102JR 906 RS1/16S473J

R 907 RS1/16S473JR 908 RS1/16S472JR 909 RD1/4PU103JR 910 RS1/16S0R0JR 911 RS1/16S122J

R 912 RD1/4PU103JR 913 RS1/16S101JR 914 RD1/4PU152JR 916 RS1/16S221JR 918 RS1/16S1R0J

R 944 RD1/4PU152JR 951 RD1/4PU153JR 953 RS1/16S472JR 954 RD1/4PU102JR 955 RD1/4PU473J

R 971 RS1/16S103JR 981 RS1/16S472JR 982 RS1/16S222JR 983 RD1/4PU221JR 984 RD1/4PU221J

CAPACITORS

C 310 CKSRYB105K6R3C 311 CKSRYB104K16C 313 CKSRYB105K6R3C 314 CKSRYB104K16C 315 CKSRYB102K50

C 316 CKSRYB102K50C 330 CEJA470M10C 331 CEJA100M16C 332 CKSRYB104K16C 333 CEJA4R7M35

C 334 CEJA4R7M35C 335 CKSRYB104K16C 336 CKSRYB153K25C 337 CKSRYB153K25C 338 CKSRYB104K16

C 340 CEAL2R2M50C 341 CEJA2R2M50C 346 CCSRCH100D50C 347 CCSRCH100D50C 348 CCSRCH100D50

C 349 CCSRCH100D50C 350 CEJA330M10C 352 CCSRCH101J50C 361 CEJA2R2M50C 362 CKSQYB225K10

C 363 CEJA100M16C 364 CKSQYB474K16C 365 CKSQYB474K16C 366 CKSQYB474K16C 367 CKSQYB474K16

C 368 CKSQYB474K16C 369 CKSQYB474K16C 370 CKSQYB474K16C 371 CKSQYB474K16C 372 CKSQYB225K10

C 390 CKSRYB104K16C 391 3300µF/16V CCH1368C 411 CKSRYB223K25C 412 CKSRYB223K25C 413 CKSRYB102K50

C 414 CEJA220M10C 415 CKSRYB473K16C 416 CEAL101M10C 417 CKSRYB472K50C 418 CKSRYB472K50

C 419 CCSRCH101J50C 420 CCSRCH101J50C 441 CKSRYB182K50C 442 CKSRYB223K25C 462 CKSRYB123K25



44

DEH-1330R,1300R,1310

C 463 CKSRYB123K25C 466 CEJA1R0M50C 467 CEJA1R0M50C 490 CKSQYB103K50C 493 CKSRYB472K50

C 612 CEJA4R7M35C 613 CKSRYB473K16C 614 CCSRCH101J50C 621 CCSRCH101J50C 630 CKSRYB473K16

C 631 CEAL2R2M50C 650 CKSRYB104K16C 711 CEAL220M6R3C 712 CKSRYB104K16C 714 CKSRYB471K50

C 715 CKSRYB104K16C 718 CKSRYB471K50C 719 CEAL220M6R3C 720 CKSRYB104K16C 725 CCSRCH270J50

C 726 CCSRCH270J50C 901 CEJA101M10C 902 CKSRYB473K16C 903 470µF/16V CCH1331C 904 CKSRYB473K16

C 905 330µF/16V CCH1326C 906 CKSRYB103K50C 907 CEJA101M16C 941 CKSRYB473K16C 971 CKSRYB103K50

C 972 CKSRYB473K16C 981 CEJA101M10C 982 CKSRYB102K50C 983 CKSRYB473K16

Unit Number : CWM7295(DEH-1310/X1M/EE)Unit Name : Tuner Amp Unit

MISCELLANEOUS

IC 301 IC PML003AMIC 302 IC TDA7386IC 601 IC PE5196AIC 602 IC S-80834ANYIC 970 IC TPD1018F

Q 346 Transistor RN1610Q 350 Transistor DTA124EKQ 351 Transistor DTC114EKQ 353 Transistor DTA124EKQ 411 Transistor 2SC2412K

Q 650 Transistor 2SA1037KQ 901 Transistor 2SC2412KQ 902 Transistor 2SC2412KQ 903 Transistor 2SD1859Q 904 Transistor 2SD2396

Q 905 Transistor 2SB1243Q 906 Transistor DTC114EKQ 920 Transistor RN46A1Q 951 Transistor 2SA1037KQ 981 Transistor 2SD2396

Q 982 Transistor RN46A1D 650 Diode 1SS270D 651 Diode 1SS270D 652 Diode 1SS270D 653 Diode 1SS270

D 654 Diode 1SS270D 655 Diode 1SS270D 901 Diode HZS7L(C2)D 902 Diode S5688GD 903 Diode S5688G

D 904 Diode HZS7L(A1)D 905 Diode S5688GD 906 Diode HZS6L(B2)D 907 Diode HZS9L(B3)D 941 Diode S5688G

D 942 Diode S5688GD 951 Diode 1SS270D 952 Diode 1SS270D 981 Diode HZS9L(B1)L 310 Ferri-Inductor LAU1R0M

L 401 Ferri-Inductor LAU4R7KL 402 Ferri-Inductor LAU2R2KL 403 Inductor LAU100KL 610 Ferri-Inductor LAU101KL 611 Ferri-Inductor LAU2R2K

L 650 Ferri-Inductor LAU2R2KL 901 Choke Coil 600µH CTH1221L 951 Ferri-Inductor LAU2R2KX 610 Crystal Resonator 4.194304MHz CSS1023AR 946 Arrester DSP-201M-S00B

FM/AM Tuner Unit CWE1566

RESISTORS

R 310 RD1/4PU222JR 311 RD1/4PU222JR 332 RS1/16S221JR 333 RS1/16S221JR 334 RS1/16S221J


R 346 RS1/16S0R0JR 351 RS1/16S102JR 352 RS1/16S103JR 353 RS1/16S103JR 354 RS1/16S331J

R 360 RD1/4PU153JR 411 RS1/16S681JR 412 RS1/16S681JR 413 RS1/16S681JR 414 RS1/16S103J

R 415 RS1/16S681JR 416 RD1/4PU473JR 417 RD1/4PU472JR 418 RS1/16S473JR 419 RS1/16S473J



R 464 RS1/16S272JR 465 RS1/16S272JR 468 RS1/16S0R0JR 469 RS1/16S0R0JR 610 RD1/4PU153J



A

45

DEH-1330R,1300R,1310

R 611 RS1/16S363JR 619 RS1/16S0R0JR 620 RS1/16S223JR 622 RD1/4PU222JR 623 RD1/4PU222J


R 629 RS1/16S473JR 630 RS1/16S822JR 631 RD1/4PU102JR 649 RS1/16S222JR 650 RD1/4PU222J


R 656 RS1/16S103JR 657 RD1/4PU102JR 658 RD1/4PU102JR 660 RS1/16S1R0JR 681 RD1/4PU681J



R 908 RS1/16S472JR 909 RD1/4PU103JR 910 RS1/16S0R0JR 911 RS1/16S122JR 912 RD1/4PU103J

R 913 RS1/16S101JR 914 RD1/4PU152JR 916 RS1/16S221JR 918 RS1/16S1R0JR 944 RD1/4PU152J

R 951 RD1/4PU153JR 953 RS1/16S472JR 954 RD1/4PU102JR 955 RD1/4PU473JR 971 RS1/16S103J

R 981 RS1/16S472JR 982 RS1/16S222JR 983 RD1/4PU221JR 984 RD1/4PU221J

CAPACITORS

C 310 CKSRYB105K6R3C 311 CKSRYB104K16C 313 CKSRYB105K6R3C 314 CKSRYB104K16C 315 CKSRYB102K50

C 316 CKSRYB102K50C 330 CEJA470M10C 331 CEJA100M16C 332 CKSRYB104K16C 333 CEJA4R7M35

C 334 CEJA4R7M35C 336 CKSRYB153K25C 337 CKSRYB153K25C 340 CEAL2R2M50C 341 CEJA2R2M50

C 346 CCSRCH100D50C 347 CCSRCH100D50C 348 CCSRCH100D50C 349 CCSRCH100D50C 350 CEJA330M10

C 361 CEJA2R2M50C 362 CKSQYB225K10C 363 CEJA100M16C 364 CKSQYB474K16C 365 CKSQYB474K16

C 366 CKSQYB474K16C 367 CKSQYB474K16C 368 CKSQYB474K16C 369 CKSQYB474K16C 370 CKSQYB474K16

C 371 CKSQYB474K16C 372 CKSQYB225K10C 390 CKSRYB104K16C 391 3300µF/16V CCH1368C 411 CKSRYB223K25

C 412 CKSRYB223K25C 413 CKSRYB102K50C 414 CEJA220M10C 415 CKSRYB473K16C 416 CEAL101M10

C 417 CKSRYB472K50C 419 CCSRCH101J50C 462 CKSRYB123K25C 463 CKSRYB123K25C 490 CKSQYB103K50

C 612 CEJA4R7M35C 613 CKSRYB473K16C 614 CCSRCH101J50C 628 CCSRCH150J50C 629 CCSRCH150J50

C 630 CKSRYB473K16C 631 CEAL2R2M50C 650 CKSRYB104K16C 901 CEJA101M10C 902 CKSRYB473K16

C 903 470µF/16V CCH1331C 904 CKSRYB473K16C 905 330µF/16V CCH1326C 906 CKSRYB103K50C 907 CEJA101M16

C 941 CKSRYB473K16C 971 CKSRYB103K50C 972 CKSRYB473K16C 981 CEJA101M10C 982 CKSRYB102K50

C 983 CKSRYB473K16

Unit Number : CWM7306(DEH-1330R/X1M/EW)Unit Name : Keyboard Unit

MISCELLANEOUS

IC 1801 IC PD6340AD 1701 LED SML210DTD 1702 LED SML210DTD 1703 LED SML210DTD 1704 LED SML210DT



B

46

DEH-1330R,1300R,1310

D 1705 LED SML210DTD 1706 LED SML210DTD 1707 LED SML210DTD 1708 LED SML210DTD 1801 Diode MA152WK

D 1802 Diode MA152WAD 1811 LED NSSW440-9159D 1812 LED NSSW440-9159X 1801 Ceramic Resonator 4.97MHz CSS1422IL 1801 Lamp 14V 40mA CEL1638

IL 1802 Lamp 14V 40mA CEL1638LCD CAW1632

RESISTORS




R 1803 RS1/16S471JR 1804 RS1/16S471JR 1805 RS1/16S471JR 1806 RS1/16S471J

CAPACITORS

C 1801 CKSRYB103K50C 1811 CKSQYF104Z25C 1812 CKSQYF104Z25

Unit Number : CWM7305(DEH-1300R/X1M/EW)Unit Name : Keyboard Unit

MISCELLANEOUS

IC 1801 IC PD6340AD 1701 LED SML210PTD 1702 LED SML210PTD 1703 LED SML210PTD 1704 LED SML210PT

D 1705 LED SML210PTD 1706 LED SML210PTD 1707 LED SML210PTD 1708 LED SML210PTD 1801 Diode MA152WK



RESISTORS





CAPACITORS


Unit Number : CWM7307(DEH-1310/X1M/EE)Unit Name : Keyboard Unit

MISCELLANEOUS

IC 1801 IC PD6340AD 1701 LED SML210PTD 1702 LED SML210PTD 1703 LED SML210PTD 1704 LED SML210PT

D 1705 LED SML210PTD 1706 LED SML210PTD 1707 LED SML210PTD 1708 LED SML210PTD 1801 Diode MA152WK



RESISTORS





CAPACITORS




B

B

47

DEH-1330R,1300R,1310

Unit Number : CWX2411Unit Name : Control Unit

MISCELLANEOUS

IC 201 IC UPD63711GCIC 301 IC BA5985FMIC 701 IC BA05SFPQ 101 Transistor 2SB1132D 801 LED CL203IRXTU

D 802 LED CL203IRXTUX 201 Ceramic Oscillator 16.934MHz CSS1456S 801 Spring Switch(HOME) CSN1051S 802 Spring Switch(CLAMP) CSN1052

RESISTORS



R 302 RS1/16S153JR 303 RS1/16S103JR 501 RS1/16S102JR 502 RA4C681JR 601 RS1/16S102J

R 602 RS1/16S102JR 605 RS1/16S0R0JR 606 RS1/16S0R0JR 801 RS1/8S751JR 803 RS1/8S751J

R 902 RS1/16S0R0JR 906 RS1/16S0R0J

CAPACITORS

C 101 CKSRYB102K50C 102 CKSRYB104K16C 103 CEV101M6R3C 104 CEV470M6R3C 105 CKSQYB334K16

C 106 CKSQYB334K16C 107 CKSQYB334K16C 201 CKSRYB104K16C 202 CKSRYB471K50C 203 CKSRYB104K16

C 205 CEV101M6R3C 206 CKSRYB104K16C 207 CKSRYB104K16C 208 CKSRYB104K16C 209 CKSRYB104K16

C 210 CKSRYB332K50C 211 CKSRYB104K16C 212 CKSRYB104K16C 213 CKSRYB392K50C 214 CKSRYB104K16

C 215 CKSRYB104K16C 216 CCSRCJ3R0C50C 217 CCSRCH270J50C 218 CKSRYB104K16C 219 CCSRCH181J50

C 220 CCSRCH510J50C 221 CKSRYB682K25C 222 CEV220M6R3C 223 CKSRYB103K25C 224 CKSRYB224K10

C 301 CEV101M10C 603 CCSQSL152J50C 604 CCSQSL152J50C 702 10µF/10V CCH1349C 703 CKSQYB334K16

Unit Number :Unit Name : Photo Unit(S8)

Q 1 Photo-transistor CPT230SX-TUQ 2 Photo-transistor CPT230SX-TU

Miscellaneous Parts List

Pickup Unit(Service)(P8) CXX1285M 1 Motor Unit(CARRIAGE) CXB2190M 2 Motor Unit(LOADING) CXB2195M 3 Motor Unit(SPINDLE) CXB2562

Fuse(10A) CEK1136



C

D

48

DEH-1330R,1300R,1310

1) Precautions• This unit uses a single power supply (+5V) for the reg-

ulator. The signal reference potential, therefore, isconnected to REFO(approx. 2.5V) instead of GND.If REFO and GND are connected to each other by mis-take during adjustments, not only will it be impossi-ble to measure the potential correctly, but the servowill malfunction and a severe shock will be applied tothe pick-up. To avoid this, take special note of the fol-lowing.Do not connect the negative probe of the measuringequipment to REFO and GND together. It is especiallyimportant not to connect the channel 1 negativeprobe of the oscilloscope to REFO with the channel 2negative probe connected to GND.Since the frame of the measuring instrument is usual-ly at the same potential as the negative probe, changethe frame of the measuring instrument to floating sta-tus.If by accident REFO comes in contact with GND,immediately switch the regulator or power OFF.

• Always make sure the regulator is OFF when connect-ing and disconnecting the various filters and wiringrequired for measurements.

• Before proceeding to further adjustments and mea-surements after switching regulator ON, let the playerrun for about one minute to allow the circuits to stabi-lize.

• Since the protective systems in the unit's software arerendered inoperative in test mode, be very careful toavoid mechanical and /or electrical shocks to the sys-tem when making adjustment.

• Disc detection during loading and eject operations isperformed by means of a photo transistor in thisunit.Consequently, if the inside of the unit is exposedto a strong light source when the outer casing isremoved for repairs or adjustment, the following mal-functions may occur.

*During PLAY, even if the eject button ispressed,the disc will not be ejected and the unitwill remain in the PLAY mode.

*The unit will not load a disc.When the unit malfunctions this way, either re-posi-tion the light source, move the unit or cover the phototransistor.

2) Test ModeThis mode is used for adjusting the CD mechanismmodule of the device.

• Test mode starting procedureReset while pressing the 4 and 6 keys together.

• Test mode cancellationSwitch ACC, back-up OFF.

• After pressing the EJECT key, do not press any otherkey until the disk is completely ejected.

• If the ] or [ key is pressed while focus search is inprogress, immediately turn the power off (otherwisethe actuator may be damaged due to adhesion of thelenses).

• Jump operation of TRs other than 100TR continuesafter releasing the key. CRG move and 100TR jumpoperations are brought into the “Tracking close” sta-tus when the key is released.

• Powering Off/On resets the jump mode to “1TR”, andthe automatic adjustment value to the initial value.

6. ADJUSTMENT

6.1 CD ADJUSTMENT

49

DEH-1330R,1300R,1310

- Flow Chart

4

3

Reset

SOURCE

New test mode

6

[

BAND

BAND

BAND

BAND

BAND

3

*2*1

6

6

6

6

1

2

1

2]

] [

Select CD

Focus ModeSelect

Focus Close/S Curve Check

CRG- Auto AdjustmentDisplay Select

<Tracking Servo Close> CRG+

RF AGC Coefficient Display/Rough Servo and RF AGC

Tracking Open

TrackingOpen

T. Close andFit Servo

] [

1

3

Display

2

3

Displayor

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

CRG-CRG+ T.BalanceAdjustment

*4F, T, RF AGC/F.Bias Display Select

F, T AGC andRF AGC

Power ON(Adjustment for T.Offset)

*5 *6 *6

*7CRG/TR Jump NO.Select

CRG+/TR Jump+

CRG-/TR Jump-

Power OFF

Display

Display

Display

T.Close andF,T AGC andRF AGC andFit Servo

Power ON(Not adjustment for T.Offset)

Display

Display

2

Power OFF

Power OFF

Power OFF 8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

8x 8x 8xTRK SECMIN

9x 9x 9xTRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

00 00 00TRK SECMIN

99 99 99TRK SECMIN

or

91 91 91TRK SECMIN

0x 0x 0xTRK SECMIN

00 00 00TRK SECMIN

99 99 99TRK SECMIN

Test Mode In

*3

*1

*3

*6

*2

*5

*7

*4

F.Cancel T.Offset The original display

1TR/4TR/10TR/32TR/100TR"00", "99"→Focus Close / "01"→S.Curve

1TR 4TR91(81) 92(82)

CRG Move96(86)

100TR95(85)

32TR94(84)

10TR93(83)

Focus Close00(99)

LD Off02

S.Curve01

CRG Move,100TR Jump

TRK, MIN, SEC F.AGC Gain T.AGC Gain F.Bias

50

DEH-1330R,1300R,1310

• Note :The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mecha-nism module is adjusted on the production line to match the CD mechanism module and is thus the best adjustedPU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, ifthe PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment :If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to performtrack search operations, or taking a long time for track searching.

• Method :

• Measuring Equipment • Oscilloscope, Two L.P.F.• Measuring Points • E, F, REFOUT• Disc • ABEX TCD-784• Mode • TEST MODE

• Checking Procedure1. In test mode, load the disc and switch the 5V regulator on.2. Using the ] and [ buttons, move the PU unit to the innermost track.3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-

ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on thefourth press.

4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-ence is within 75° . Refer to the photographs supplied to determine the phase angle.

5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is anyimprovement. If, after trying this a number of times, the grating angle does not become less than 75° then themechanism should be judged to be at fault.

• NoteBecause of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may beseen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-age angle.

• HintReloading the disc changes the clamp position and may decrease the "wobble".

F

REFO

E

100kΩ

390pF

100kΩ

390pF

E

REFO

F

REFO

L.P.F.

L.P.F.

CONTROL UNIT

Xch Ych

Oscilloscope

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

51

DEH-1330R,1300R,1310

Grating waveform Ech → Xch 20mV/div, ACFch → Ych 20mV/div, AC

45°

0°

75°

60°

30°

90°

52

DEH-1330R,1300R,1310

7. GENERAL INFORMATION

7.1 DIAGNOSIS

7.1.1 TEST MODE

- Error Messages

If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the

error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the

users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (min-

utes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains

in blank as before.

2) Head unit display examples

Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR–xx ERR–xx E–xx

OR

Err–xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)

10 Electricity Carriage Home NG CRG can't be moved to inner diameter.

CRG can't be moved from inner diameter.

→ Failure on home switch or CRG move mechanism.

11 Electricity Focus Servo NG Focusing not available.

→ Stains on rear side of disc or excessive vibrations on REWRITABLE.

12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).

→ Failure on spindle, stains or damages on disc, or excessive vibrations.

Subcode NG A disc not containing CD-R data is found. Turned over disc are found,

though rarely.

→ Failure on home switch or CRG move mechanism.

RF AMP NG An appropriate RF AMP gain can't be determined.

→ CD signal error.

17 Electricity Setup NG APC protection doesn't work. Focus can be easily lost.

→ Damages or stains on disc, or excessive vibrations.

30 Electricity Search Time Out Failed to reach target address.

→ CRG tracking error or damages on disc.

A0 System Power Supply NG Power (VD) is ground faulted.

→ Failure on SW transistor or power supply (failure on connector).

Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).

Unreadable TOC does not constitute an error. An intended operation continues in this case.

A newly designed head unit must conform to the example given above.

Upper digits of an error code are subdivided as shown below:

1x: Setup relevant errors, 3x: Search relevant errors, 3x: Search relevant errors, Ax: Other errors.

53

DEH-1330R,1300R,1310

- New Test Mode

S-CD plays the same way as before.

If an error such as off focus, spindle unlocking, unreadable sub-code, or sound skipping occurs after setup, its

cause and time occurred (in absolute time) are displayed.

During setup, operational status of the control software (internal RAM: CPOINT) is displayed.

These displays and functions are prepared for enhancing aging in the servicing and efficiency of trouble analysis.

(1) Shifting to the New Test Mode

1 Turn on the current test mode by starting the reset from the key.

2 Select S-CD for the source through the specified procedure including use of the [SOURCE] key, and inserting the

disc. Then, press the [Jump Mode Selector] key while maintaining the regulator turned off.

3 After the above operations, the new test mode remains on irrespective of whether the S-CD is turned on or off.

You can reset the new test mode by turning on the reset start.

* With some products, the new test mode can be reset through the same operations as that employed for shifting to

the STBY mode (while maintaining the Acc turned off).

(2) Key Correspondence

Key Test mode New test mode

(Example) Power Off Power On In-play Error Production

BAND To power on To power off – Time/Err.No. switching

(offset adjustment performed)

] – FWD-Kick FF/TR+ –

[ – REV-Kick REV/TR- –

1 – T.Close (AGC performed) Scan –

/parameter display switching

2 – T.BAL adjustment Mode –

/T.Open

3 To power on F.Close/RF AGC/AGC – –

(offset adjustment not performed)

6 – Mode switching Auto/Manu –

/T.Close (no AGC)/Jump switching

Note: Eject and CD on/off is performed in the same procedure as that for the normal mode.

(3) Cause of Error and Error Code

Code Class Contents Description and cause

40 Electricity Off focus detected. FOK goes low.

→ Damages/stains on disc, vibrations or failure on servo.

41 Electricity Spindle unlocked. FOK = Low continued for 50 msec.


42 Electricity Sub-code unreadable. Sub-code was unreadable for 50 msec.


43 Electricity Sound skipping detected. Last address memory function was activated.


Note: Mechanical errors during aging are not displayed.

The error codes should be indicated in the same way as in the normal mode.

54

DEH-1330R,1300R,1310

(4) Display of Operational Status (CPOINT) during SetupStatus No. Contents Protective action01 Carriage move to home position started. None02 Carriage is moving toward inner diameter. Specified 10 seconds has been passed or failure

on home switch.03 Carriage is moving toward outer diameter. Specified 10 seconds has been passed or failure

on home switch.05 Carriage outer diameter feed (1 second) in progress. None11 Setup started. None12 Spindle rotation and focus search started. None13 Waiting for focus close (XSI=Low). Specified focus search time has been passed.14 Waiting for focus close (FOK=High). (After AGC) Specified focus search time has been passed.15 Waiting for focus close (FOK=High). (Before AGC) Specified focus search time has been passed.16 Rough AGC in progress. Off focus.17 Setup (1/2) before T balance adjustment is started. Off focus.18 Setup (2/2) before T balance adjustment is started. Off focus.24 T balance adjustment (1/2). Off focus.25 T balance adjustment (2/2). Off focus.26 Standing by after spindle rough servo is over. Off focus.27 Setup before RF AGC (first) is started. Off focus.28 RF AGC (first) in progress. Off focus.29 Setup before RF AGC (second) is started. Off focus.30 RF AGC (second) in progress. Off focus.31 Tracking close in progress. Off focus.32 Standing by after tracking is closed. Off focus.33 Focus AGC started. Off focus.34 Focus AGC in progress. Tracking AGC started. Off focus.35 Tracking AGC in progress. Off focus.

Spindle processes applicable servo.36 Check of MIRR and LOCK pin. RF AGC in progress. Off focus. Spindle not locked.

CRG close in progress. Check of sub-code. Sub-code unreadable.

(5) Display Examples

1) During Setup (When status no. = 11)

TRK No. MIN. SEC.

11 11' 11"

2) During Operation (TOC read, TRK search, Play, FF and REV)

The same as in the normal mode.

3) When a Protection Error Occurred

Switch to the following displays (A) and (B) using the [BAND] switch:

(A) Error occurrence timing display in absolute time.

An example: Error occurred in 12th tune at 34'56" in absolute time.

TRK No. MIN. SEC.

12 34' 56"

(B) Error No. display

An example: Error #40 (Off focus is detected)

ERROR-40

55

DEH-1330R,1300R,1310

- Removing the Tuner Amp Unit

Remove the three screws and then remove

the Cover. (Fig.2)

Remove the two screws. (Fig.2)

Remove the screw. (Fig.3)

Straight the tabs at fore locations indicated

and then remove the Tuner Amp Unit.

(Fig.3)

- Removing the Case Unit (not shown)

1. Remove the Case Unit.

- Removing the CD Mechanism Module (Fig.1)

Remove the four screws.

Disconnect the connector and then remove the CD

Mechanism Module (not shown).

- Removing the Panel Assy (not shown)

1.Disconnect the two stoppers and then remove the

Panel Assy.

Fig.1

Fig.2

Fig.3Tuner Amp Unit

Cover

CD Mechanism Module

7.1.2 DISASSEMBLY

56

DEH-1330R,1300R,1310

- Removing the Upper Frame

1. Remove six Springs A, two Springs B and four

Screws.

2. Remove two Tabs situated on rear side of the Upper

Frame, remove two Arms on the front side, then

remove two Tabs on the front side.

- Removing the Carriage Mechanism

1. Disengage the Carriage Mechanism from the two

dampers situated in the front side by driving it up,

then disengage and remove the mechanism from the

one damper by driving it up aslant into front side

direction.

Note : When assembling the Carriage Mechanism, coat

the dampers with alcohol prior to the assembly.

- Removing the Clamp Arm Assy

1. Remove a Spring A, a B and a Spring C.

2. Drive the Clamp Arm Assy up into rear side direction,

then disengage the arm from its current position

Finally, drive the assembly approximately 45 degrees

upward, then slide the assembly toward right side to

remove it.

B

A

B A

A

A

Arm

Arm

A

B

C

Upper Frame

Carriage Mechanism Section

Clamp Arm Assy Section

A

A

57

DEH-1330R,1300R,1310

- Removing the Guide Arm Assy

1. Remove a connector, a spring A and B

2. Drive the Guide Arm Assy up aslant into rear side

direction, then remove it from a Pin. Finally, drive the

assembly approximately 45 degrees upward, then

slide the assembly toward left side to remove it.

Note : When assembling the guide arm assembly, route

the cord inside the assembly. In this operation,

care must be exercised so that cord may be

caught by the gear.

- Removing the LO Arm Assy

1. Remove two Pins to dismount the LO Arm Assy.

- Removing the Control Unit and the Spindle

Motor

1. Remove from the connector after mounting the short

pin on the flexible PCB of the pickup unit.

2. Remove two Soldered joints, then remove two

Screws A.

3. Remove two connectors and a Screw B.

4. Disengage the Control Unit from two Tabs, then dis-

mount the unit by sliding it toward left.

5. Dismount the Spindle Motor.

A

Guide Arm Assy Section

B

Pin

LO Arm Assy Section

Spindle Motor

A A

Control Unit

Short Pin

B

58

DEH-1330R,1300R,1310

- Removing the Loading Motor and Carriage

Motor

1. Remove the Spring and two Screws A.

2. Dismount the Loading Motor.

3. Remove the Belt, a Screw B, two Screws C, a Guide

and a Screw Unit.

4. Dismount the Carriage Motor.

Note : When assembling the Belt, use care so that it

may not be contaminated by grease.

- Removing the Pickup Unit

1. Remove two Screws and a Shaft.

2. Dismount the Pickup Unit.

Pickup Unit

Shaft

CGuide

B

Screw Unit Carriage Motor

AA

CBelt

Loading Motor

59

DEH-1330R,1300R,1310

7.1.3 CONNECTOR FUNCTION DESCRIPTION

579 13

468 210121416

111315

1. BACK UP 2. GND 3. NC 4. ACC 5. B.REM 6. NC 7. TEL MUTE 8. NC 9. FL-10. RL-11. FL+12. RL+13. FR-14. RR-15. FR+16. RR+

PRE OUT ANTENNA

60

DEH-1330R,1300R,1310

7.2 PARTS

7.2.1 IC

- Pin Functions(PE5195A, PE5196A)Pin No. Pin Name I/O Format Function and Operation

1 MODEL1 I Model select input2 NL1 I Noise level input3 NL2DT I Noise level input 24 AVSS AVSS5 ST I Stereo input6 SD I SD signal input 7 AREF1 AVREF18 KYDT I Key data input9 DPDT O C Key data output

10 SDBW I SDBW input11 TUNPDI I PLL IC data input12 TUNPDO O C PLL IC data output13 TUNPCK O C PLL IC clock output14 TUNPCE O C PLL IC chip enable output15 currq O C Tuner voltage FIX output16 XSI I C CD LSI serial data input(TSI)17 XSO O C CD LSI serial data output(TSO)18 XSCK O C CD LSI serial clock output(TSCK)19 drst O C RDS decoder reset output20 ADPW O C A/D converter power output21 fm/AM O C Tuner power supply control output22 VDCONT O C VD power supply control output23 CONT O C Servo driver power control output24 XAO O C CD LSI command / data control output25 xrst O C CD LSI reset control output26 xstb O C CD LSI strobe output27 CLAMP I Disc clamp sense input28 MIRR I Mirror detection input 29 FOK I Focus OK signal input30 LOCK I Spindle lock detector input31 CDLOAD O LOAD motor loading control output32 TELIN I Cellular mute input33 VSS VSS34 CDEJECT O LOAD motor eject control output35 CD5VON O C CD +5V power supply control output

36–39 NC Not used40 RECIEVE O C RDS decoder receiving output41 swvdd O C Grille microcomputer power supply control output42 SYSPW O C System power supply control output43 ILMPW O C Illumination power output44 mute O C Mute output45 PEE O C Beep tone output46 LOCH O C LOCH output47 RDS57K I 57kHzBP-OUT sense input48 TUNPCE2 O C EEPROM chip enable output49 PCL O C Test mode clock adjustment output50 VCK O C Clock output for electronic volume51 VDT O C Data output for electronic volume52 ANTPW O Antenna power output53 VST O Strobe pulse output for electronic volume54 DALMON O Stand-by output

55,56 NC Not used57 LOCL O LOCL output58 rdslk I RDSLK input

61

DEH-1330R,1300R,1310

Pin No. Pin Name I/O Format Function and Operation59 RDT I RDS data input60 reset Reset61 LDET I PLL lock detection input62 RCK I RDS clock input63 asens I ACC power sense input64 bsens I Back up power sense input65 dsens I Grille detach sense input66 TMUTE O C Tuner mute output67 NC Not used68 VDD VDD69 X2 Crystal oscillator connection pin70 X1 Crystal oscillator connection pin71 IC(VPP) IC(VPP)72 NC Not used73 TESTIN I Test program mode input74 AVDD AVDD75 AVREF0 AVREF076 SL I Signal level input77 TEMP I Temperature detection input78 VDSENS I VD power supply sense input79 DINC I Disc detection input80 EJTD I Disc eject position detect input

801

20

21 40

41

60

61

*PE5195A, PE5196A

Output Format MeaningC C MOS output

IC's marked by* are MOS type.

Be careful in handing them because they are very liable

to be damaged by electrostatic induction.

S-80834ANY

1 2 31

OUT VDD VSS

62

DEH-1330R,1300R,1310

- Pin Functions (PD6340A)Pin No. Pin Name I/O Function and Operation

1-5 SEG4-0 O LCD segment output6-9 COM3-0 O LCD common output 10 VLCD LCD drive power supply

11-14 KST3-0 O Key strobe output15,16 KDT0,1 I Key data input (analogue input)

17 REM I Remote control reception18 DPDT I Display data input19 NC Not used20 KYDT O Key data output21 MODA GND22 X0 Crystal oscillator connection pin23 X1 Crystal oscillator connection pin24 VSS GND

25,26 KDT2,3 I Key data input27 NC Not used28 KST4 O Key strobe output

29-32 NC Not used33-55 SEG35-13 O LCD segment output

56 VDD Power supply57-64 SEG12-5 O LCD segment output

*PD6340A

49

4833

32

17

16 1

64

63

DEH-1330R,1300R,1310

- Pin Functions (UPD63711GC)Pin No. Pin Name I/O Function and Operation

1 D.GND Logic circuit GND2 RFOK O RFOK signal output3 rst I Reset signal input4 A0 I Command/parameter identification signal input5 stb I Data strobe signal input6 sck I Clock signal input for serial data input/output7 SO O Serial data and status signal output8 SI I Serial data input9 xtalen I Crystal oscillation control pin

10 D.VDD Positive power supply terminal to logic circuit11 DA.VDD Positive power supply terminal to D/A converter12 R_OUT O Right channel audio output signal13 DA.GND D/A converter GND14 REGC I The outside putting capacitor connection pin for SCF regulator15 DA.GND D/A converter GND16 L_OUT O Left channel audio output signal17 DA.VDD Positive power supply terminal to D/A converter18 R+ O Right channel audio data output19 R- O Right channel audio data output20 L- O Left channel audio data output21 L+ O Left channel audio data output22 X.VDD Positive power supply terminal to crystal oscillation circuit23 XTAL I Crystal oscillator connect pin24 xtal O Crystal oscillator connect pin25 X.GND Crystal oscillation circuit GND26 D.VDD Positive power supply terminal to logic circuit27 EMPH O Output pin for the pre-emphasis data in the sub-Q code28 FLAG O Flag output pin to indicate that audio data currently being output consists

of noncorrectable data29 DIN I Serial data input to internal DAC30 DOUT O Serial audio data output31 SCKIN I Serial clock input to internal DAC32 SCKO O Audio data that is output from DOUT changes at rising edge of this clock33 LRCKIN I LRCK signal input to internal DAC34 LRCK O Signals to distinguish the right and left channels of the audio data output

from DOUT35 HOLD O Defect detection output36 TX O Digital audio interface data output37 D.GND Logic circuit GND38 C16M O Oscillator clock buffering output39 LIMIT I Status of the pin is output at Bit 5 of the status output40 D.VDD Positive power supply terminal to logic circuit41 LOCK O EFM synchronous detection signal42 RFCK O Frame synchronous signal of XTAL-system43 MIRR O MIRR output44 PLCK O Monitor pin of bit clock45 D.GND Logic circuit GND46 C1D1 O Output pin for indicating the C1 error correction results47 C1D2 O Output pin for indicating the C1 error correction results48 C2D1 O Output pin for indicating the C2 error correction results49 C2D2 O Output pin for indicating the C2 error correction results50 C2D3 O Output pin for indicating the C2 error correction results51 D.VDD Positive power supply terminal to logic circuit52 PACK O CD-TEXT PACK synchronous signal53 TSO O CD-TEXT data serial output54 TSI I CD-TEXT control parameter serial input55 tsck I CD-TEXT serial clock input56 TSTB I CD-TEXT parameter strobe signal input57 D.GND Logic circuit GND

64

DEH-1330R,1300R,1310

Pin No. Pin Name I/O Function and Operation58 TEST0 I Test pin59 TEST1 I Test pin60 ATEST O Test pin61 A.GND Analog circuit GND62 FD O Focus drive output63 TD O Tracking drive output64 SD O Sled drive output65 MD O Spindle drive output66 DAC0 O DAC output for adjustment67 DAC1 O DAC output for adjustment68 DAC2 O DAC output for adjustment69 DAC3 O DAC output for adjustment70 A.VDD Positive power supply terminal to analog circuit71 EFM O EFM signal output72 ASY I EFM comparator reference voltage input73 C3T 3T detection capacitor additional pin74 RFI I RF signal input for EFM data regulation75 AGCO O RF signal output of after gain adjustment 76 AGCI I RF-AGC amplifier input77 RFO O RF summing amplifier output78 EQ2 RF amplifier equalizer parts additional pin79 EQ1 RF amplifier equalizer parts additional pin80 RF- I RF summing amplifier inverted input81 A.GND Analog circuit GND82 A I Photo detector A input83 C I Photo detector C input84 B I Photo detector B input85 D I Photo detector D input86 F I Photo detector F input87 E I Photo detector E input88 A.VDD Positive power supply terminal to analog circuit89 REFOUT O Reference electric potential output90 FE- I Focus error amplifier inverted input91 FEO O Focus error amplifier output92 TE- I Tracking error amplifier inverted input93 TEO O Tracking error amplifier output94 TE2 O Tracking error output of after amplification95 TEC I Tracking comparator input96 A.GND Analog circuit GND97 PD I PD detection signal input for LD output monitor 98 LD O LD control current output99 PN I APC circuit control polarity set pin

100 A.VDD Positive power supply terminal to analog circuit

20

21

40

41 60

61

80

1

100

76

26

125

7551

50

*UPD63711GC

65

DEH-1330R,1300R,1310

No. Symbol I/O Explain1 STIND O stereo "Low" when the FM stereo signals are received.

indicator To be pulled up to the "VDD" at 47kΩ.2 FMSD O FM station "High" when signals are received. To be pulled up to the "VDD" at 47kΩ

detector Meanwhile, 10kΩ should be used when taking diver FIX trigger from hereand "High: 0.9VDD or more" and "Low: 250mV or less".(Should satisfy the diver IC specifications)

3 NL1 O noise level-1 "High" when noise is received. Output for the RDS. GND at 47kΩ //1,800pF.4 NL2 O noise level-2 "High" when noise is received. Output for the RDS. GND at 36kΩ //330pF.5 Rch O R channel FM stereo "R-ch" signal output or AM audio output.

output Add the specified di-emphasis constant. 6 Lch O L channel FM stereo "L-ch" signal output or AM audio output.

output Add the specified di-emphasis constant. 7 WC write control EEPROM write control. Writing permissible at "Low". Normally open. 8 SDBW O SD bandwidth SD bandwidth signal output. For detection of detuning data for the RDS.9 NC Not used

10 VDD power Power supply pin for the digital section.supply D.C. 5V +/- 0.25V. Be careful about overlapping noise in the logic section.

11 DGND digital ground Grounding for the digital section. 12 CE2 I chip enable-2 EEPROM chip enable. Active a "Low"

To be pulled up to the "VDD" at 47kΩ13 SL I/O signal level Received FM/AM signal level (strength) output.

Connect the specified load resistor and capacitor (10k Ω + 39k Ω //4,700pF) 14 DI/DO I/O data input/ Data input/Data output

data output To be pulled up to the "VDD" at 47kΩ15 CK I clock Clock input To be pulled up to the "VDD" at 47kΩ16 CE1 I chip enable-1 AF·RF chip enable. Active at "High" To be grounded at 47kΩ17 NC Not used18 LDET O lock detector Active at "Low". To be pulled up to the "VDD" at 47kΩ19 CREQ I current request Active at "Low". To be grounded at 47kΩ20 NC Not used21 COMP O composite signal FM composite signal output. r out < 100Ω22 VCC power supply Analog section power supply pin.D.C.8.4V +/- 0.3V 23 LOCH I local high FM local high pin. When seeking local high, apply 5V together with "LOCL". 24 FMLOCL I FM local low FM local low pin. When seeking local low, apply 5V to the base of the NPN

transistor with which the specified resistor is being connected to the emitter. Keep it open in case of ordinary marketed models.

25 LOCL I local low FM/AM local low pin. When seeking local low, apply 5V to the base of the NPN transistor. Since this pin is exclusive for AM when the FMLOCL is in use,do not drive it under FM.

26 RFGND RF ground Grounding for the antenna section. 27 FMANT I FM antenna input FM antenna input. 75Ω. Serge absorber (DSP-201M-S00B) is necessary. 28 AMANT I AM antenna input AM antenna input. High impedance.

Connect to the antenna through an L (LAU type) of 4.7µH.To cope with thepower transmission line hums, insert a series circuit consisting of an L(a coil of about 100mH) + R (a resistor of 470 Ω to 2.2kΩ) between the GND.

IC 3EEPROM

FM/AM TUNER UNIT

28

27

FM/AM 1ST IF 10.7MHzT51 Q51 CF51 CF52 CF53

IC1MIXER, IF AMP, DET.

6

21

18LDET

COMP

2225 10 14 12 15 16 8 13 2 3 4

CF202

VDDVCC

DI/D

O

CE

2

CK

CE

1

SD

BW

SL

FMS

D

NL1

NL2

IC 2 FM MPX

AMANT

FMANT

ATT

ATT

AMRF

FMRF

IMG ADJ

RF ADJ

X90110.25MHz

ANT ADJ

LOCL23

LOCH

AMDETMPXREF 41kHz

AM 2ND IF450kHz

19

CR

EQ

11

DG

ND

1

ST

IND

L ch

5R ch

924

NC

FMLO

CL

20177N

C

NC

WC

26 RFGND

66

DEH-1330R,1300R,1310

SEG37

SEG35

SEG34

SEG33

SEG32

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

SEG22

SEG21

SEG20

SEG18

SEG17

SEG16

SEG15

SEG14

SEG13

SEG12

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG2

NC

NC

SEG19

SEG36

COM2B

COM0A

COM2C

COM3B

COM2D

COM1B

COM0B

SEG39

SEG38

COM3A

COM2A

COM1A

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

21

1

47

46

45

44

43

42

41

39

38

50

49

48

40

COM2B

COM0A

COM2C

COM3B

COM2D

COM1B

COM0B

COM3A

COM2A

COM1A

SE

GM

EN

T

CO

MM

ON

7.2.2 DISPLAY

- CAW1632(DEH-1330R/X1M/EW, DEH-1300R/X1M/EW)

67

DEH-1330R,1300R,1310

SEG37

SEG35

SEG34

SEG33

SEG32

SEG31

SEG30

SEG29

SEG28

SEG27

SEG26

SEG25

SEG24

SEG23

SEG22

SEG21

SEG20

SEG18

SEG17

SEG16

SEG15

SEG14

SEG13

SEG12

SEG11

SEG10

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

SEG3

SEG2

NC

NC

SEG19

SEG36

COM2B

COM0A

COM2C

COM3B

COM2D

COM1B

COM0B

SEG39

SEG38

COM3A

COM2A

COM1A

37

36

35

34

33

32

31

30

29

28

27

26

25

24

23

22

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

21

1

47

46

45

44

43

42

41

39

38

50

49

48

40

COM2B

COM0A

COM2C

COM3B

COM2D

COM1B

COM0B

COM3A

COM2A

COM1A

SE

GM

EN

T

CO

MM

ON

- CAW1633(DEH-1310/X1M/EE)

68

DEH-1330R,1300R,1310

7.3 OPERATIONAL FLOW CHART

VDD=5V68pin

Power ON

BSENS=L

ASENS=L

DSENS=L

bsens64pin

asens63pin

dsens65pin

ADPW←H20pin

SWVDD←L41pin

Source keys operative

Completes power-on operation.(After that, proceed to each source operation.)

SYSPW←H42pin

Starts communication with Grille microcomputer.

Source ON

300ms

300ms

In case of the above signal, the communication with Grille microcomputer may fail.If the time interval is not 300msec, the oscillator may be defective.

69

DEH-1330R,1300R,1310

Buttons 1–6

EJECT buttonCD loading slot

AUDIO button

5/∞/2/3 buttons

SOURCE button

+/– buttons

BAND button

LOCAL/BSM button

Detach button

EQ button

LOUD button

CLOCK button

8. OPERATIONS AND SPECIFICATIONS

8.1 OPERATIONS

Key Finder

Buttons 1–6

EJECT buttonCD loading slot

AUDIO button

5/∞/2/3 buttons

SOURCE button

+/– buttons

BAND button

LOCAL/BSM button

Detach button

EQ button

TA button

PTY button

Head Unit (DEH-1330R,1300R)

Head Unit (DEH-1310)

70

DEH-1330R,1300R,1310

Bas

ic O

pera

tion

Bas

ic O

pera

tion

of T

uner

Pres

et T

unin

g

•Y

ou c

an m

emor

ize

broa

dcas

t st

atio

ns in

but

tons

1th

roug

h 6

for

easy

, one

-tou

ch s

tati

on r

ecal

l.

Pres

et s

tatio

n re

call

2 se

cond

s or

less

Bro

adca

st s

tatio

n pr

eset

mem

ory

2 se

cond

s or

mor

e

Not

e:•

Up

to 1

2 FM

sta

tions

(6

in F

1 (F

M1)

and

F2

(FM

2))

and

6 M

W/L

W

stat

ions

can

be

stor

ed in

mem

ory.

•Y

ou c

an a

lso

use

the

5or

∞bu

ttons

to r

ecal

l bro

adca

st s

tatio

nsm

emor

ized

in b

utto

ns 1

thro

ugh

6.

Pres

et N

umbe

r Ind

icat

orB

and

Indi

cato

rFreq

uenc

y In

dica

tor

Thi

s pr

oduc

t’s A

F fu

nctio

n ca

n be

sw

itche

d O

N a

nd O

FF. A

F sh

ould

be

switc

hed

OFF

for

norm

al tu

ning

ope

ratio

ns.

To L

iste

n to

Mus

icT

he f

ollo

win

g ex

plai

ns th

e in

itial

ope

ratio

ns r

equi

red

befo

re y

ou c

an li

sten

to m

usic

.

Not

e:•

Loa

ding

a d

isc

in th

is p

rodu

ct.

1.Se

lect

the

des

ired

sou

rce

(e.g

. Tun

er).

Eac

h pr

ess

of th

e SO

UR

CE

but

ton

sele

cts

the

desi

red

sour

ce in

the

follo

win

g or

der:

Bui

lt-in

CD

pla

yer

=T

uner

Not

e:•

Whe

n no

dis

c is

set

in th

is p

rodu

ct, b

uilt-

in C

D p

laye

r so

urce

will

not

cha

nge.

•W

hen

this

pro

duct

’s b

lue/

whi

te le

ad is

con

nect

ed to

the

car’

s A

uto-

ante

nna

rela

y co

ntro

l ter

min

al,

the

car’

s A

uto-

ante

nna

exte

nds

whe

n th

is p

rodu

ct’s

sou

rce

is s

witc

hed

ON

. To

retr

act t

he a

nten

na,

switc

h th

e so

urce

OFF

.

2.R

aise

or

low

er t

he v

olum

e.

3.Tu

rn t

he s

ourc

e O

FF.

Hol

d fo

r 1

seco

nd

Eac

h pr

ess

chan

ges

the

Sour

ce ..

.

Man

ual a

nd S

eek

Tuni

ng

•Y

ou c

an s

elec

t th

e tu

ning

met

hod

by c

hang

ing

the

leng

th o

f ti

me

you

pres

s th

e 2

/3bu

tton

.

Man

ual T

unin

g (s

tep

by s

tep)

0.5

seco

nds

or le

ss

Seek

Tun

ing

0.5

seco

nds

or m

ore

Not

e:•

If y

ou c

ontin

ue p

ress

ing

the

butto

n fo

r lo

nger

than

0.5

sec

onds

, you

can

ski

p br

oadc

ast

stat

ions

. See

k T

unin

g st

arts

as

soon

as

you

rele

ase

the

butto

n.•

Ster

eo in

dica

tor

“”

light

s w

hen

a st

ereo

sta

tion

is s

elec

ted.

Ban

d F1 (

FM1)

=

F2 (

FM2)

=

MW

/LW

71

DEH-1330R,1300R,1310

Bas

ic O

pera

tion

Bas

ic O

pera

tion

of B

uilt-

in C

D P

laye

r

Trac

k N

umbe

r Ind

icat

orPl

ay T

ime

Indi

cato

r

CD L

oadi

ng S

lot

Not

e:•

The

bui

lt-in

CD

pla

yer

play

s on

e st

anda

rd 1

2 cm

or 8

cm

(si

ngle

) C

D a

t a ti

me.

Do

not u

se a

nad

apte

r w

hen

play

ing

8 cm

CD

.•

Don

’t in

sert

any

mat

eria

ls e

xcep

t for

CD

into

CD

load

ing

slot

.

Trac

k Se

arch

and

Fas

t For

war

d/Re

vers

e

•Y

ou c

an s

elec

t be

twee

n T

rack

Sea

rch

or F

ast

For

war

d/R

ever

se b

y pr

essi

ngth

e 2

/3bu

tton

for

a di

ffer

ent

leng

th o

f ti

me.

Tra

ck S

earc

h0.

5 se

cond

s or

less

Fast

For

war

d/R

ever

se

Con

tinue

pre

ssin

g

Not

e:•

If a

dis

c ca

nnot

be

inse

rted

ful

ly o

r pl

ayba

ck f

ails

, mak

e su

re th

e re

cord

ed s

ide

is d

own.

Push

the

EJE

CT

but

ton

and

chec

k th

e di

sc f

or d

amag

e be

fore

rei

nser

ting

it.•

If a

dis

c is

inse

rted

with

the

reco

rded

sid

e up

, it w

ill b

e ej

ecte

d au

tom

atic

ally

aft

er a

few

mom

ents

.•

If th

e bu

ilt-i

n C

D p

laye

r ca

nnot

ope

rate

pro

perl

y, a

n er

ror

mes

sage

(su

ch a

s “E

RR

OR

-14”

)ap

pear

s on

the

disp

lay.

Ref

er to

“B

uilt-

in C

D P

laye

r’s

Err

or M

essa

ge”.

Ejec

t Not

e:•

The

CD

fun

ctio

n ca

n be

turn

ed O

N/O

FFw

ith th

e di

sc r

emai

ning

in th

is p

rodu

ct.

• A

dis

c le

ft p

artia

lly in

sert

ed a

fter

eje

c-tio

n m

ay in

cur

dam

age

or f

all o

ut.

DEH-1330R,1300R,1310

2.R

ear

outp

ut

1.T

his

prod

uct

3.A

nten

naja

ck

4.Fu

se

5.

7.C

ap(1

*)W

hen

notu

sing

this

term

inal

,do

notr

emov

eth

eca

p.

1*

2* 4*

3* 5*

9.Y

ello

w(2

*)To

term

inal

alw

ays

supp

lied

with

pow

erre

gard

less

ofig

nitio

nsw

itch

posi

tion.

8.Y

ello

w(3

*)B

ack-

up(o

rac

cess

ory)

12.B

lack

(gro

und)

Tove

hicl

e(m

etal

)bo

dy.

24.B

lue/

whi

te(7

*)To

Aut

o-an

tenn

are

lay

cont

rol

term

inal

(max

.300

mA

12V

DC

).

6.C

onne

ctle

ads

ofth

esa

me

colo

rto

each

othe

r.

18.B

lue/

whi

teTo

syst

emco

ntro

lter

min

alof

the

pow

eram

p(m

ax.3

00m

A12

VD

C).

23.B

lue/

whi

te(6

*)

11.R

ed(4

*)To

elec

tric

term

inal

cont

rolle

dby

igni

tion

switc

h(1

2V

DC

)O

N/O

FF.

10.R

ed(5

*)A

cces

sory

(or

back

-up)

14.S

peak

erle

ads

Whi

teW

hite

/bla

ckG

ray

Gra

y/bl

ack

Gre

enG

reen

/bla

ckV

iole

tV

iole

t/bla

ck

:Fro

ntle

ft+

:Fro

ntle

ft≠

:Fro

ntri

ght+

:Fro

ntri

ght≠

:Rea

rle

ft+

:Rea

rle

ft≠

:Rea

rri

ght+

:Rea

rri

ght≠

Not

e:D

epen

ding

onth

eki

ndof

vehi

cle,

the

func

tioof

3*an

d5*

may

bedi

ffer

ent.

Inth

isca

se,b

esu

reto

conn

ect2

*to

5*an

d4*

to3*

.

20.R

ear

spea

ker

(Lef

t)

19.S

yste

mre

mot

eco

ntro

l

16.P

ower

amp

(sol

dse

para

tely

)

15.C

onne

ctin

gco

rds

with

RC

Api

npl

ugs

(sol

dse

para

tely

).

22.P

erfo

rmth

ese

conn

ectio

nsw

hen

usin

ga

diff

eren

tam

p(s

old

sepa

rate

ly).

21.R

ear

spea

ker

(Rig

ht)

25.

13.I

SOco

nnec

tor

Not

e:In

som

eve

hicl

es,t

heIS

Oco

nnec

tor

may

bedi

vide

din

totw

o.In

this

case

,be

sure

toco

nnec

tto

both

conn

ecto

rs.

The

pin

posi

tion

ofth

eIS

Oco

nnec

tor

will

diff

erde

pend

son

the

type

ofve

hicl

e.C

onne

ct6*

and

7*w

hen

Pin

5is

anan

tenn

aco

ntro

ltyp

e.In

anot

her

type

ofve

hicl

e,ne

ver

conn

ect6

*an

d7*

.

17.Y

ello

w/b

lack

Ifyo

uus

ea

cellu

lar

tele

phon

e,co

nnec

titv

iath

eA

udio

Mut

ele

adon

the

cellu

lar

tele

phon

e.If

not,

keep

the

Aud

ioM

ute

lead

free

ofan

yco

nnec

tions

.

+ ≠

+ ≠

Conn

ectio

n D

iagr

am (D

EH-1

330R

,130

0R)

72

73

DEH-1330R,1300R,1310

+ ≠

+ ≠

+ ≠

+ ≠

+ ≠

+ ≠

Blu

e/w

hite

Tosy

stem

cont

rolt

erm

inal

ofth

epo

wer

amp

orA

uto-

ante

nna

rela

yco

ntro

lter

min

al(m

ax.3

00m

A12

VD

C)

.

Con

nect

ing

cord

sw

ithR

CA

pin

plug

s(s

old

sepa

rate

ly)

Syst

emre

mot

eco

ntro

l

Rea

rsp

eake

rR

ear

spea

ker

Rig

ht

Fron

tspe

aker

Rea

rsp

eake

r

Whi

teG

ray

Whi

te/b

lack

Gre

en

Gre

en/b

lack

Gra

y/bl

ack

Vio

let

Vio

let/b

lack

Fron

tspe

aker

Rea

rsp

eake

r

Left

Perf

orm

thes

eco

nnec

tions

whe

nus

ing

adi

ffer

enta

mp

(sol

dse

para

tely

).

With

a2

spea

ker

syst

em,d

ono

tcon

nect

anyt

hing

toth

esp

eake

rle

ads

that

are

not

conn

ecte

dto

spea

kers

.

Yel

low

Tote

rmin

alal

way

ssu

pplie

dw

ithpo

wer

rega

rdle

ssof

igni

tion

switc

hpo

sitio

n.

Bla

ck(g

roun

d)To

vehi

cle

(met

al)

body

.

Red

Toel

ectr

icte

rmin

alco

ntro

lled

byig

nitio

nsw

itch

(12

VD

C)

ON

/OFF

.

Pow

eram

p(s

old

sepa

rate

ly)

Fuse

Yel

low

/bla

ckIf

you

use

ace

llula

rte

leph

one,

conn

ecti

tvia

the

Aud

ioM

ute

lead

onth

ece

llula

rte

leph

one.

Ifno

t,ke

epth

eA

udio

Mut

ele

adfr

eeof

any

conn

ectio

ns.

Rea

rou

tput

Thi

spr

oduc

t

Ant

enna

jack

Conn

ectio

n D

iagr

am (D

EH-1

310)

74

DEH-1330R,1300R,1310

8.2 SPECIFICATIONS

GeneralPower source .......... 14.4 V DC (10.8 – 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption ...................................... 10.0 ADimensions

(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm(front face) .............. 188 (W) × 58 (H) × 19 (D) mm

Weight ...................................................................... 1.4 kgElectrode dark current .................................... 6mA or less

Amplifier Maximum power output ...................................... 45 W × 4Continuous power output .................................... 25 W × 4

(DIN45324, +B = 14.4 V)Load impedance .......................... 4 Ω (4 – 8 Ω allowable)Preout maximum output

level/output impedance ............................ 2.2 V/1 kΩEqualizer (3-Band Equalizer)

(Low) .................................................. Level: ±12 dB(Mid) .................................................... Level: ±12 dB(High) .................................................. Level: ±12 dB

Loudness contour(Low) .................. +3.5 dB (100 Hz), +3 dB (10 kHz)(Mid) ................ +10 dB (100 Hz), +6.5 dB (10 kHz)(High) ................ +11 dB (100 Hz), +11 dB (10 kHz)

(volume: –30 dB)

CD playerSystem .................................... Compact disc audio systemUsable discs .................................................. Compact discSignal format...................... Sampling frequency: 44.1 kHz

Number of quantization bits: 16; linearFrequency characteristics................ 5 – 20,000 Hz (±1 dB)Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network)Dynamic range ............................................ 92 dB (1 kHz)Number of channels ............................................ 2 (stereo)

FM tunerFrequency range ...................................... 87.5 – 108 MHzUsable sensitivity

.................... 9 dBf (0.8 µV/75 Ω, mono, S/N: 30 dB)50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 Ω, mono)Signal-to-noise ratio ...................... 70 dB (IEC-A network)Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)Frequency response ...................... 30 – 15,000 Hz (±3 dB)Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)

MW tunerFrequency range ........................ 531 – 1,602 kHz (9 kHz)Usable sensitivity .............................. 18 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

LW tunerFrequency range ........................................ 153 – 281 kHzUsable sensitivity .............................. 30 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

Note:• Specifications and the design are subject to possi-

ble modification without notice due to improve-ments.

- DEH-1330R,1300R

75

DEH-1330R,1300R,1310

- DEH-1310

GeneralPower source .......... 14.4 V DC (10.8 – 15.1 V allowable)Grounding system ........................................ Negative typeMax. current consumption ...................................... 10.0 ADimensions

(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm(front face) .............. 188 (W) × 58 (H) × 19 (D) mm

Weight ...................................................................... 1.4 kgElectrode dark current .................................... 6mA or less

AmplifierMaximum power output ...................................... 45 W × 4Continuous power output .................................... 25 W × 4

(DIN45324, +B = 14.4 V)Load impedance .......................... 4 Ω (4 – 8 Ω allowable)Preout maximum output level/

output impedance .................................... 2.2 V/1 kΩEqualizer (3-Band Equalizer)

(Low) .................................................. Level: ±12 dB(Mid) .................................................... Level: ±12 dB(High) .................................................. Level: ±12 dB

Loudness contour(Low) ..................+3.5 dB (100 Hz), +3 dB (10 kHz)(Mid) ..................+10 dB (100 Hz), +6.5 dB (10 kHz)(High) ..................+11 dB (100 Hz), +11 dB (10 kHz)

(volume: –30 dB)

CD playerSystem .................................... Compact disc audio systemUsable discs .................................................. Compact discSignal format .................... Sampling frequency: 44.1 kHz

Number of quantization bits: 16; linearFrequency characteristics .............. 5 – 20,000 Hz (±1 dB)Signal-to-noise ratio ...... 94 dB (1 kHz) (IEC-A network)Dynamic range ............................................ 92 dB (1 kHz)Number of channels ............................................ 2 (stereo)

FM tunerFrequency range ............................................ 65 – 74 MHz

87.5 – 108 MHzUsable sensitivity ......................................................10 dBf

(0.9 µV/75 Ω, mono, S/N: 30 dB)50 dB quieting sensitivity ........................................ 15 dBf

(1.5 µV/75 Ω, mono)Signal-to-noise ratio ...................... 70 dB (IEC-A network)Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)Frequency response ...................... 30 – 15,000 Hz (±3 dB)Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)

MW tunerFrequency range ........................ 531 – 1,602 kHz (9 kHz)Usable sensitivity .............................. 18 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

LW tunerFrequency range ........................................ 153 – 281 kHzUsable sensitivity .............................. 30 µV (S/N: 20 dB)Selectivity .................................................. 50 dB (±9 kHz)

Note:• Specifications and the design are subject to possi-

ble modification without notice due to improve-ments.

Documents

Pioneer DEH 1330R,DeH 1300R,DeH 1310 Service Manual