The revolutionary mixing techniquewith significant
advantages.
HORIZONTAL SCREW MIXER 07/2010
Technical data
Part no. 00 08 92 61 400 V, three phases32 A feed line, 5 x 2.5
mm2
Part no. 00 09 43 61 230 V, FC single phase32 A feed line, 3 x
2.5 mm2
Drive 4 kW, 50 Hz, aluminium geared motorRotation per minute 280
rpm, mixer motorTransformer minimum10 kVAWater connection Hose
3/4", at least 2.5 bar
water pressure at running machinePump capacity 60 – 90 l/min,
depending on dosing shaft
45 l/min standardContinuous sound level 72 ± 1 dB
(A)DimensionsOverall length 2030 mmWidth with control unit mounted
720 mmHeight with control unit mounted 730 mmWeightsTotal weight
PFT LOTUS XL 171.5 kg incl. control unitMixing shaft 15.0
kgManifold box 19.0 kgMotor flange with protection bow and motor
47.5 kgMiddle body 37.0 kgMixing tube with outlet 21.5 kgControl
box 21.6 kg
Knauf PFT GmbH & Co. KGP.O. Box 60 97343 IphofenEinersheimer
Straße 53 97346 IphofenGermany
Knauf Gips KGDry construction-, Gypsum plaster- and
Soil-Systems
Knauf AMF GmbH & Co. KGCeiling Systems
Knauf Integral KGGypsum Fibre Material
Knauf Marmorit GmbH Mineral Facade Systems
Knauf Dämmstoffe GmbHPolystyrene Insulating Material
Knauf Insulation GmbH Glasswool-Isolation, XPS
Knauf Perlite GmbHaquapanel ® CementBoards, Perlit
Knauf PFT Technical Hotline:
+ 49 9323 31-1818
Phone + 49 9323 31-760Fax + 49 9323 31-770
[email protected]
www.pft.eu
All rights and technical changes reserved. We provideguarantee
as far as faultless and proper finishing of ourmachines is
concerned. Figures given in relation to output,equipment and
performance are based on experience andcan vary in case of changing
circumstances. Furthermore, theinstructions of the material/mortar
manufacturers must beobserved. Alterations, reprints and
photomechanicalreproductions, even in extracts, require the
permission ofKnauf PFT GmbH & Co. KG.
PFT LOTUS XL – GB/07.10/PFT
Geared motor aluminium 4 kW withmotor protection bow and
opensealing of the gear, motor tiltable
Separate divided control unit,consisting of control box andwater
manifold box
Control box with automatic phasesequence relay, motor
protectionswitches outside adapted, timeswitch
Water manifold box: water flowmeter, pressure reducer,
needle/fine adjustment valve, gauge,water pump
Removable rubber mixing tube
Dosing zone and first mixingchamber made of rubber
Mixing shaft without middle axlewith exchangeable dosing
segment(can be used double)
Operating instructions
PFT LOTUS XL
PFT LOTUSXL Basic equipment
MADE IN GERMANYMADE IN GERMANY
PFT – THE FLOW OF PRODUCTIVITY PFT – THE FLOW OF
PRODUCTIVITY
PFT LOTUS XLTurnable dosingshaft segmentIt is especially
economical as it can be used twice. If the wearing requests it, the
segment can be turned by 180°. Thanks to this theendurance is
doubled.
Rubber mixing tubeThis mixing tube is robust conceivedue to the
multiply mesh insert for an easy and quick cleaning. It can be
removed easily without any tools.
Dosing and mixingshaftThe new and revolutionary dosingand mixing
shaft as one unit without middle axle. This means no sticking of
the material and the cleaning is as easy and fast as never.
Control unitThe separate control unit with inte- grated water
manifold and outsideadapted protection switches can be assembled
directly at the machine as well as at the container.
The water manifold box with inte-grated water pump can be
removedfrom the control box without tools. Different versions if in
230 V or400 V are available on desire.
Rest material zoneThis zone can be cleaned easilyand fast thanks
to the swingingdrive and due to the optimised dryarea there is no
waste of material.
The revolutionary mixing technique with significant
advantages.
Easy and fast cleaning
The PFT LOTUS XLmixes continuously and fully automati-cally all
premixed drylime/cement basedmortars up to a grain size of 8
mm.
Masonry mortarsFilling plastersPlastersFloor screedsLevelling
compounds and much more
Further advantages:Conveying capacity can be increa-sed up to
60/90 l/min. Specialdosing shafts are optional available.
Best varnishing due to burning thepowder paint at 200°.
It can be assembled by only oneperson. Thanks to the
mountingdevice with integrated crane loops.
Safety regulations correspond tothe CE-regulations.
Protected gearAn adapter with open sealing saves the shaft seal
of the gear.
Mortar outletThe rubber outlet is produced by one piece. In case
that material sticks it can be removed easily and fast.
Combinable withPFT conveying pumpsFor mortar transports we
recommendour PFT conveying pumps, as e. g. PFT SWING L or PFT ZP 3
XL.
Rubber dosing zoneThe test on hard construction sites shows:
rubber is significantly longer living as steel. This saves
money!
Example fora simplecontrol unit
Field of application:
