Instructional Sheet
Part Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533
[email protected]
ALKW8-RGB72Important: Read all instructions prior to
installation.
Diagram 1
Remote Battery Replacement
Remote Functions
1. Remove three philips head screws and remove the button
panel.2. Carefully remove battery and replace with new.3.
Reposition button panel then insert and tighten screws
1. Connect strips to Splitter Cable then connect to Controller.
Temporarily apply power to the controller and test strip locations
for proper lighting effect.
2. Mark the desired location of the strips. Mount strips using
double sided tape or silicone in desired location and away from
heat sources and moving parts.
3. Mount controller and connection box in dry locations away
from heat sources and moving parts and route power wires to power
source then connect. Route white antenna wire away from metal
objects for maximum operating range.
Multi Color 8 Piece Accent Light Kit
2 - 5” Waterproof Accent Light Strips4 - 6.75” Waterproof Accent
Light Strips2 - 8.75” Waterproof Accent Light Strips1 - RF RGB
Accent Light Controller1 - RF Wireless Key Chain Remote (RCW-RFR)1
- Splitter Cable1 -12V 27A Battery
Parts Included
Installation
Specifications
RG
B LE
D F
lexi
ble
Ligh
t Stri
p
Battery
1/4” Snap Spades
8-Way Splitter
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
Power Supply
ORCPS connector
(CPS-F2ST)
(CPS-12VDC-50W)
Fuse
3A
RG
B LE
D F
lexi
ble
Ligh
t Stri
p
8-Way Splitter
WhiteAntenna
BlueBrakeOverride
To Brake Switch
ControllerRGB RF
BlackGround
RedPower In
BlueWire
Running Light Cicuit (+)
Ground
WhiteAntenna
PSC-164Brake Light Circuit (+)
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
ControllerRGB RF
Input Voltage 9~14.8 VDCController Output Current 3 x 1A
Maximum
Fuse Size 3AOperating Temperature -4 ~122° F (-20~50° C)
Strip IP Rating Waterproof IP67Static Color Dynamic Modes 2Seven
Color Dynamic Modes 2
Static Colors 18Override Mode 1
Brightness Levels 5Remote Battery 12V 27A x 1Remote Range 33
Feet (10m) Maximum
Remote Frequency 315 MHzFCC ID 2AFXS-JX-R001
Warranty 2 Years
Remote comes paired to the controller. Use the following
procedure if additional remotes are required.On power up, LEDs will
be green indicating pairing mode for three seconds. During green
pairing mode, press button “A” then “B” to pair a new remote.
Remote Pairing
Wiring
Output Connector Polarity PurposeBlack Positive (+) Common
AnodeRed Negative (-) Red LED Cathode
Green Negative (-) Green LED CathodeBlue Negative (-) Blue LED
Cathode
Input Wires Polarity PurposeBlack Negative (-) Ground In (-)Red
Positive (+) 9~14.8 VDC Power In (+)
Blue (see below) Positive (+) 9~14.8 VDC Red Override Signal In
(+)Blue wire activates red single color mode at full brightness
while voltage is applied. Use for brake override if required. Works
as brake override even when controller is
in standby mode.Button Functions
Cycles up through 18 single color modes and two 7 color modes.
Press and hold for dimming 80%, 60%, 40%, 20% and back to
100% during single color modes.Activates Flash Modes during
single color modes. Switches
between Flash/Flash/Long Pause and Flash/Flash/Short Pause
during flash modes. Increases cycle speed during 7 color modes
Activates Fading Mode during single color modes. Decreases cycle
speed during 7 color modes.
On/OffHold for 6 seconds to return to Mode 1 (Static Red)
RCW-RFR
Slid
e C
over
Instructional Sheet
Part Number:
4400 Earth City Expy, St. Louis MO 63045 866-590-3533
[email protected]
ALKW8-RGB72Important: Read all instructions prior to
installation.
Multi Color 8 Piece Accent Light Kit
Mode Sequence & Functions
Mode Button A Button B Button C Button D1 Red Flash Modes Fade
Mode On/Off 2 Blue Flash Modes Fade Mode On/Off 3 Light Pink Flash
Modes Fade Mode On/Off 4 Green Flash Modes Fade Mode On/Off 5 Gold
Flash Modes Fade Mode On/Off 6 Light Blue Flash Modes Fade Mode
On/Off 7 Orange Flash Modes Fade Mode On/Off 8 Hot Pink Flash Modes
Fade Mode On/Off 9 Light Green Flash Modes Fade Mode On/Off
10 Cool White Flash Modes Fade Mode On/Off 11 Aqua Flash Modes
Fade Mode On/Off 12 Pale Rose Flash Modes Fade Mode On/Off 13
Purple Flash Modes Fade Mode On/Off 14 White Flash Modes Fade Mode
On/Off 15 Warm White Flash Modes Fade Mode On/Off 16 Sky Blue Flash
Modes Fade Mode On/Off 17 Sea Green Flash Modes Fade Mode On/Off 18
Lemon Flash Modes Fade Mode On/Off 19 7 Color Flash Speed Up Speed
Down On/Off 20 7 Color Fade Speed Up Speed Down On/Off
FCC Statement
Auxilary Running/Brake Light Example
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation. Any changes or modifications in construction
of this device which are not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:–Reorient or relocate the receiving
antenna.–Increase the separation between equipment and
receiver.–Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.–Consult the
dealer or an experienced radio/TV technician for help.
Diagram 2
RG
B LE
D F
lexi
ble
Ligh
t Stri
p
Battery
1/4” Snap Spades
8-Way Splitter
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
Power Supply
ORCPS connector
(CPS-F2ST)
(CPS-12VDC-50W)
Fuse
3A
RG
B LE
D F
lexi
ble
Ligh
t Stri
p
8-Way Splitter
WhiteAntenna
BlueBrakeOverride
To Brake Switch
ControllerRGB RF
BlackGround
RedPower In
BlueWire
Running Light Cicuit (+)
Ground
WhiteAntenna
PSC-164Brake Light Circuit (+)
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
V+ G R B
ControllerRGB RF
Tip: To use RGB LED light strips for auxilary running
lights/brake lights, set controller for red color and dim to 40% or
20% to simulate parking lights. Attach Blue wire from controller to
the positive brake light wire on the motorcycle. After pairing mode
the LED light strips will be dim red when controller is on and the
LED light strips will be full brightness red when brake is applied.
Controller will activate full brightness red mode anytime the
controller is powered and a positive signal is applied to the blue
wire. Strips will now function as auxiliary Tail/Brake lights to
enhance visibility and safety.
