OPERATINGINSTRUCTIONMANUAL

MODELS HP22 Be HP22A

HP25 Be HP2'pA, .~"\'~.f

PHOENIX ARMS@ DELUXE RANGE KIT

AT HOME ON THE RANGE

PURSUANT To STATE OF CALIFORNIAP.C. 12088.6

A WARNING

CHILDREN ARE ATTRACTED TO AND CAN OPERATE FIREARMS THAT CAN CAUSE

SEVERE INJURIES OR DEATH. PREVENT CHILD ACCESS BY ALWAYS KEEPING GUNS

LOCKED AWAY AND UNLOADED WHEN NOT IN USE. IF YOU KEEP A LOADED

FIREARM WHERE A CHILD OBTAINS AND IMPROPERLY USES IT, YOU MAY BE FINED

OR SENT TO PRISON.

A AOVERTENCIA

A LOS NINOS LOS ATRAEN LAS ARMAS DE FUEGO Y LAS PUEOEN HACER

FUNCIONAR. ELLOS PUEDEN CAUSARSE LESIONES GRAVES Y LA MUERTE. EVITE

QUE LOS NINOS TENGAN ACCESO A LAS ARMAS DE FUEGO GUARDANDOLAS

SIEMPRE CON LLAVE Y DESCARGADAS CUANDO NO LAS ESTE UTILIZANDO. 51

USTED TlENE UN ARMA DE FUEGO CARGADA EN UN LUGAR EN QUE UN NINO TIENE

ACCESO A ELLA Y LA USA INDEBIDAMENTE, LE PUEDEN DAR UNA MULTA 0

ENVIARLO A LA CARCEL.

! DANGERDo NOT STORE, CARRY, DROP, DRIVE A VEHICLE, BICYCLE, WALK ORRUN WITH A LIVE ROUND IN THE CHAMBER. A GUN THAT IS DROPPED,BUMPED OR 'JARRED WITH A LIVE ROUND IN THE CHAMBER MIGHTACCIDENTALLY DISCHARGE, EVEN WITH THE SAFETY ON, CAUSINGINJURY TO YOU OR SOMEONE ELSE.

ALWAYS WEAR PROPER SHOOTING GLASSES TO PREVENT EYE INJURYFROM FLYING PARTICLES.

ALWAYS USE HEARING PROTECTION TO PREVENT EAR DAMAGE DUETO REPEATED EXPOSURE TO GUN FIRE NOISE.

Do NOT HANDLE THIS PISTOL WITH OUT FIRST CHECKING CHAMBERFOR LIVE CARTRIDGES, PISTOL SHOULD BE CLEANED FOLLOWINGEACH USE. REFER TO CLEANING INSTRUCTIONS IN THIS BOOKLET.

NEVER SHOOT AT A HARD, FLAT SURFACE OR AT THE SURFACE OFWATER. BULLETS CAN RICOCHET CAUSING SERIOUS INJURY TO YOUOR OTHERS.

1

A WARNINGNEVER DEPEND ON ANY FIREARMS SAFETY DEVICE, USE CAUTION.

Do NOT ALTER ANY OF COMPONENTS OF THIS PISTOL.

IF THE TRIGGER IS PULLED WHILE THE SAFETY IS IN THE "FIRE"POSITION, THIS PISTOL WILL FIRE ANY CARTRIDGE LEFT IN THEBARREL!

AMMUNITION USED IN THIS FIREARM CONTAINS LEAD. THE USE OFTHIS AMMUNITION MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWNTO THE STATE OF CALIFORNIA TO CAUSE CANCER, ANDREPRODUCTIVE HARM. SHOOTING FULL METAL JACKET AMMUNITIONWILL GREATLY REDUCE YOUR EXPOSURE TO LEAD. ALWAYS WASHYOUR HANDS THOROUGHLY AFTER CLEANING FIREARMS ORHANDLING AMMUNITION.

NEVER POINT PISTOL AT ANYTHING YOU DO NOT INTEND TO SHOOT,DAMAGE, INJURE OR KILL.

NEVER PLACE YOUR FINGER ON THE TRIGGER UNLESS THE PISTOL ISPOINTED IN A SAFE DIRECTION AND YOU ARE READY TO SHOOT IT.

2

A CAUTIONDo NOT PUT AMMUNITION INTO THIS PISTOL, OR MAGAZINE, UNTILYOU HAVE READ THESE INSTRUCTIONS AND FULLY UNDERSTANDALL FUNCTIONS AND SAFE HANDLING OF THIS PISTOL.

Do NOT ATTEMPT TO USE THIS FIREARM UNTIL YOU HAVE

COMPLETELY READ THIS MANUAL. A THOROUGH UNDERSTANDINGOF THIS PISTOL AND ITS SAFETY SYSTEM IS ABSOLUTELYNECESSARY. NEVER PLACE YOUR FINGER ON THE TRIGGER UNLESSTHE PISTOL IS POINTED IN A SAFE DIRECTION AND YOU ARE READYTO SHOOT IT. AFTER REMOVING MAGAZINE (CLIP) FROM PISTOL,ALWAYS LOOK INTO THE CHAMBER END OF THE BARREL FOR ANYREMAINING AMMUNITION. Do NOT STORE FIREARM WITH ACARTRIDGE IN THE BARREL. KEEP OUT OF REACH OF CHILDRENAND THOSE NOT FAMILIAR WITH THE SAFE HANDLING ANDOPERATION OF THIS PISTOL.

FIREARMS SAFETY IS UP TO YOU. MAKE NO MISTAKE ABOUT IT.ALCOHOL, DRUGS AND GUNS DON'T MIX.

KEEP THIS MANUAL WITH PISTOL WHEN NOT IN USE AND WHENTRANSFERRING OWNERSHIP.

3

TABLE OF CONTENTSDANGER NOTICEWARNINGSCAUTION NOTICETABLE OF CONTENTSPISTOL DESCRIPTIONMAGAZINE INTERLOCK SAFETY SYSTEMFIRING PIN BLOCKCHECKING THE CHAMBERLOADING & UNLOADING THE MAGAZINEUNLOADING THE PISTOLFIRING OPERATIONADJUSTING SIGHTDISASSEMBLYCLEANINGASSEM BL YLOCKING STORAGE & TRANSPORT CASEBARREL & MAGAZINE COMPONENTSFRAME COMPONENTSSLIDE COMPONENTSACCESSORIES/ORDERING INFORMATIONLIFETIME WARRANTY

123456789101 112131415-16171819-20212223

4

BARREL

SLIDE

TAKE DOWNLEVER

TRIGGER

PISTOL DESCRIPTION

(ADJUSTABLE REAR SIGHT

HAMMER

MAGAZINERELEASEBUTTON

5

FIRING PINBLOCK

SAFETY

MAGAZINE

MAGAZINE INTERLOCK SAFETY

THIS SAFETY IS LOCATED AT THE TOP OF THE LEFT HAND GRIP AND CAN ONLY BEMOVED WHILE THE MAGAZINE IS FULLY INSERTED INTO THE PISTOL.

BY MOVING THE SAFETY UP TO THE TOP OF THE GRIP. THE WORD"SAFE" WILL BE EXPOSED INDICATING THE PISTOL IS IN THE

<ID

SAFE POSITION. WHILE IN THE "SAFE" POSITION. THE HAMMER~)ff~II[ CANNOT BE COCKED OR UN-COCKED. ONLY WHEN THE SAFETY

IS IN THE "SAFE" POSITION CAN THE MAGAZINE RELEASEBUTTON BE DEPRESSED AND THE MAGAZINE REMOVED. DO NOTMOVE SAFETY WHILE REMOVING MAGAZINE. ONCE THEMAGAZINE IS COMPLETELY REMOVED THE SAFETY IS LOCKED IN

THE "SAFE" POSITION UNTIL THE MAGAZINE IS FULLY REINSERTED INTO THE PISTOL.WHILE THE SAFETY IS IN THIS POSITION THE SLIDE WILL ONLY BE ABLE TO MOVEREARWARD 3/16 OF AN INCH. ENOUGH TO CHECK THE CHAMBER FOR ANYREMAINING AMMUNITION.

BY MOVING THE SAFETY DOWN THE WORD "FIRE" WILL BEEXPOSED. INDICATING THE PISTOL IS IN THE FIRING POSITION.THE MAGAZINE CANNOT BE REMOVED WITH THE SAFETY IN THISPOSITION. WHILE IN THE "FIRE" POSITION THE TRIGGER CAN BEPULLED. THE HAMMER CAN BE COCKED AND UN-COCKED ANDTHE SLIDE CAN BE CYCLED BACK AND FORTH.

6

FIRING PIN BLOCK

THE FIRING PIN BLOCK LEVER IS LOCATED ON THE LEFT SIDE OF THE SLIDE JUSTABOVE THE SERRATED FINGER GRIP.

BY ROTATING THE LEVER UP (COUNTERCLOCKWISE), A REDDOT WILL BE EXPOSED INDICATING THE FIRING PIN IS NOTBLOCKED AND A PULL OF THE TRIGGER AND FORCE OF THEHAMMER STRIKING THE FIRING PIN WILL CAUSE ANY CAR-TRIDGE IN THE BARREL TO BE FIRED.

RED DOT

BY ROTATING THE FIRING PIN BLOCK LEVER DOWN(CLOCKWISE) AND COVERING THE RED DOT, THE FIRING PIN ISBLOCKED AND RESTRICTED FROM STRIKING A CARTRIDGE INTHE CHAMBER. ONLY WHILE IN THIS POSITION SHOULD ANYATTEMPT BE MADE TO RELEASE HAMMER FROM FIRING POSI-TION. ALWAYS POINT PISTOL IN A SAFE DIRECTION, WITHTHUMB FIRMLY ON HAMMER SPUR, PULL TRIGGER ANDSLOWLY MOVE HAMMER TO ITS FORWARD POSITION. DO NOTDRY FIRE THIS PISTOL.

WARNING: IF HAMMER [S CONTINUALLY FIRED AGAINST PIN BLOCK IN THE BLOCKEDPOSITION, PIN BLOCK MAY BECOME DAMAGED AND NOT PREVENT CARTRIDGE INCHAMBER FROM FIRING.

1

CHECKING THE CHAMBER

WHENEVER PICKING UP ANY FIREARM. OR BEFORE STORING ANY FIREARM IT ISIMPORTANT TO CHECK THE CHAMBER FOR ANY LIVE ROUNDS. NEVER PLACE YOURFINGER ON THE TRIGGER WHEN CHECKING THE CHAMBER. PLACE FIRING PINBLOCK IN THE DOWNWARD POSITION COVERING THE RED DOT. PLACE THEMAGAZINE INTERLOCK SAFETY IN THE "SAFE" POSITION AND REMOVE MAGAZINE BYDEPRESSING MAGAZINE RELEASE BUTTON AND COMPLETELY REMOVE MAGAZINE.PULL SLIDE REWARD. 3/16 OF AN INCH IS AS FAR AS IT WILL BE ALLOWED TO GOWITH THE SAFETY IN THE "SAFE" POSITION. VISUALLY CHECK CHAMBER FOR ANYLIVE ROUNDS. REFER TO UNLOADING INSTRUCTIONS IN THIS MANUAL TO UNLOADPISTOL WITHOUT FIRING.

8

LOADING & UNLOADING THE MAGAZINEBEFORE ATTEMPTING TO LOAD MAGAZINE IT IS IMPORTANT THAT YOU READ AND FULLYUNDERSTAND ALL FUNCTIONS AND SAFE HANDLING OF THIS PISTOL. THE MAGAZINE.BARREL AND SLIDE ARE MARKED WITH PROPER CALIBER OF CARTRIDGE TO BE USED ANDALL MUST BE OF THE SAME CALIBER. PLACE ONE ROUND IN AT A TIME. WITH THE REAROF THE ROUND AT MIDWAY IN THE TOP OF THE MAGAZINE PUSH DOWNWARD AGAINSTTHE MAGAZINE FOLLOWER AND THEN REARWARD. THE FOLLOWING ROUNDS ARELOADED INTO THE MAGAZINE IN THE SAME MANNER. THE HP22 AND HP25 HOLD AMAXIMUM OF TEN ROUNDS IN BOTH THE STANDARD MAGAZINE AND THE EXTENDEDMAGAZINE. THERE ARE HOWIEVER. OLDER HP22 MAGAZINES THAT HOLD ELEVENROUNDS. SO BE SURE TO ALWAYS CHECK CHAMBER AND MAGAZINE FOR REMAININGAMMO WHEN YOU ARE DONE SHOOTING. DO NOT DEPEND ON COUNTING ROUNDS ASYOU SHOOT. TO UNLOAD MAGAZINE OF AMMUNITION PUSH THE TOP ROUND FORWARDAND OUT, OPPOSITE THE DIRECTION USED TO LOAD. REPEAT UNTIL ALL CARTRIDGESARE REMOVED. CAUTION DO NOT FORCE WITH ANYTHING THAT MAY DAMAGE ORRUPTURE CARTRIDGE PRIMER. ALWAYS STORE AMMUNITION SEPARATELY FROM PISTOL.

~

THE HP22 MAGAZINE IS ILLUSTRATED HERE.<-:i-7\!V))~~Ri:;VlWO-i:\;,-F;'::;:~;Ci[:'/ LOJ'.C,LD

A' 'H:f:~.:~,-.V"\"IONt5 R;:">~Oh'!I'..ir:::;~~:~~~:~P1ST()LS

t'"";'i",:c,

UNLOADING PISTOLWHILE REMOVING CARTRIDGE FROM BARREL CHAMBER. KEEPTHE PISTOL POINTED IN A SAFE DIRECTION. ROTATE FIRINGPIN BLOCK LEVER DOWN (CLOCKWISE) COMPLETELYCOVERING THE RED DOT. TAKE THE PISTOL IN YOUR RIGHTHAND WITH A FIRM GRIP. MAKING SURE YOUR FINGERS ARENOT TOUCHING THE TRIGGER.

WITH YOUR OTHER HAND FIRMLY GRASP THE SERRATEDPORTION OF THE SLIDE AND PULL IT REARWARD AS FAR AS ITWILL GO.

WITH THE SLIDE HELD AT ITS REARMOST POSITION. MOVE THESAFETY UPWARD TO THE "SAFE" POSITION.LOCKING THE SLIDEIN THE OPEN POSITION. THIS SHOULD EXTRACT ANYCARTRIDGE FROM THE BARREL CHAMBER.

THE MAGAZINE IS REMOVED BY DEPRESSING THE MAGAZINERELEASE BUTTON. REMOVE ALL CARTRIDGES FROM THEMAGAZINE. CHECK MAGAZINE CAVITY AND BARREL CHAMBERFOR ANY REMAINING CARTRIDGES. UNLOAD MAGAZINEBEFORE REINSERTING. CAUTION: IF A LOADED MAGAZINE ISREINSERTED INTO PISTOL A ROUND WILL BE CHAMBEREDWHEN CLOSING SLIDE.

1.

FIRING OPERATIONPLACE FIRiNG PIN BLOCK LEVER IN THE DOWNWARD POSITIONCOVERiNG THE RED DOT, PLACE SAFE1Y IN THE "SAFE" POSI-TiON AND REMOVE MAGAZINE. LOAD MAGAZiNE FOLLOWINGTHE INSTRUCTIONS ON PAGE 9. REINSERT LOADED MAGAZiNEINTO PISTOl.

TAKE THE PISTOL iN ONE HAND WITH A FiRM GRIP. WHiLE KEEP-ING YOUR FiNGERS OFF OF TRIGGER AND WITH PISTOL POINTEDiN A SAFE DiRECTION, MOVE SAFE1Y INTO "FIRE" POSITION(KEEP FIRiNG PIN BLOCK LEVER IN THE DOWNWARD POSiTiON).

WITH YOUR OTHER HAND FIRMLY GRASP THE SERRATED POR-TiON OF THE SLIDE AND PULL IT AS FAR REARWARD AS IT WiLLGO. RELEASE THE SLIDE FROM ITS REARMOST POSITION AL-LOWING IT TO GO FORWARD ON iTS OWN ACCORD. THIS PRO-CEDURE PLACES THE FIRST CARTRiDGE iNTO THE CHAMBERAND COCKS THE HAMMER. THE GUN IS READY FOR FIRINGWHEN THE PIN BLOCK LEVER is ROTATED UPWARD EXPOSINGTHE RED DOT. SUBSEQUENT FEEDiNG. FIRiNG AND EJECTION

OPERATiONS ARE PERFORMED AUTOMATICALLY EACH TIME THE TRiGGER is PULLEDUNTIL THE PISTOL IS EMP1Y. CAUTiON: UNLOAD PiSTOL IF YOU DO NOT INTEND TOSHOOT IT IMMEDIATELY.

11

ADJUSTING SIGHT

THIS PISTOL IS EQUIPPED WITH A FIXED FRONT BLADE SIGHT AND A WINDAGE AD-

1

JUSTABLE REAR SIGHT. THE REAR SIGHT IS ADJUSTED BY THE ADJUSTMENT SCREWLOCATED AT THE RIGHT REAR OF THE SLIDE. PISTOL SHOULD BE IN THE UNLOADEDCONDITION BEFORE ANY ATTEMPT TO ADJUST SIGHT.

, IF BULLET IS HITTING TO THE RIGHT OF TARGET CENTER. TURNSCREW TO THE RIGHT (CLOCKWISE).

IF BULLET IS HITTING TO THE LEFT OF TARGET CENTER. TURNSCREW TO THE LEFT (COUNTERCLOCKWISE).

I jrr"'-,//\ /..rll///II///I

t.

ALWAYS BE SURE OF BACKSTOP. BULLETS CAN TRAVEL UP TO FIVE MILES. NEVER,. SHOOT AT SUCH HARD SURFACES SUCH AS ROCKS. WATER. ETC.-BULLETS CAN

RICOCHET AND DAMAGE. INJURE OR KILL SOMETHING YOU DID NOT INTEND TOSHOOT.

IF YOU ARE HITTING LOW OF TARGET CENTER. RAISE YOURSIGHT OF FRONT SIGHT BLADE UP BY ONE MARK ON FRONTSIGHT BLADE TO TOP LEVEL OF REAR SIGHT.

IF YOU ARE HITTING HIGH OF TARGET CENTER. LOWER YOURSIGHT OF FRONT SIGHT BLADE BY ONE MARK TO THE LOWERLEVEL OF SIGHT BLADE NOTCH.

12

DISASSEMBL Y

THIS PISTOL MUST BE IN THE UNLOADED CONDITION BEFORE DISASSEMBLY ISPERFORMED (SEE UNLOADING PISTOL PAGE 10).

~~

PLACE FIRING PIN BLOCK LEVER IN THE DOWNWARD POSI-TION COVERING THE RED DOT. PLACE SAFETY IN THE"SAFE" POSITION. DEPRESS MAGAZINE RELEASE BUTTONAND REMOVE MAGAZINE.

PUSH ON REAR OF TAKE DOWN LEVER FORWARD TOWARDSTHE END OF THE BARREL AND LIFT BARREL END UP ANDOUT OF SLIDE AND FRAME.

TO REMOVE SLIDE. INSERT EMPTY MAGAZINE INTO PISTOLAND MOVE SAFETY TO THE "FIRE" POSITION. MOVE SLIDEFORWARD AND UP OFF OF FRAME. THIS PROCEDURE ISSUFFICIENT FOR NORMAL CLEANING AND OILING OF THEBARREL. SEE CLEANING INSTRUCTIONS.

13

CLEANING

PISTOL SHOULD BE CLEANED AS SOON AS POSSIBLE AFTER FIRING. BEFOREATTEMPTING TO CLEAN PISTOL, EMPTY CHAMBER AND MAGAZINE OF ANYAMMUNITION AND REMOVE ALL AMMUNITION FROM CLEANING AREA. COVER WORKAREA WITH OLD NEWSPAPER. IT IS BEST TO REMOVE BARREL FOR clEANING.ASSEMBLE KNOB ROD AND BRUSH. PLACE A FEW DROPS OF "BREAKFREE CLP" TOROD AND BRUSH. INSTALL BRUSH INTO BORE FROM CHAMBER END AND WORKBACK AND FORTH 5 TIMES. ALLOW OIL TO PENETRATE FOR ABOUT FIVE MINUTES.WORK BRUSH BACK AND FORTH 10 TIMES TO LOOSEN STREAKS OF LEAD ANDFOULING. ATTACH OIL SOAKED PATCH TO SLOTTED END AND WORK BACK ANDFORTH 10 TIMES. PLACE DRY PATCH ON JAG END AND PUSH THROUGH BORE.REPEAT UNTIL PATCH COMES OUT CLEAN. USING A LIGHTLY OILED PATCH ANDSLOTTED END. OIL BARREL BORE AND ALLOW TO CURE FOR AT LEAST TWO HOURS.OTHER AREAS OF PISTOL SHOULD BE CLEANED FROM FOULING WITH A SOFTCLOTH. AND OILED LIGHTLY.

"BREAKFREE CLP"

BRUSH

,1 1

)::00 , ~JAGEND

~ .

~SLOTTEDEND

KNOB

~ ~PATCHES

~SCREW 14

ASSEMBL YREMOVE ALL AMMUNITION FROMWORK AREA. PLACE EMPTY MAGA-ZINE INTO FRAME. MOVE SAFETY TO"FIRE" POSITION. MOVE HAMMER TOCOCKED POSITION.

INSTALL TAKEDOWN LEVER INTOFRAME UNDER CROSS BAR.

PLACE SLIDE DOWN ON FRAME OVEREJECTOR AND MOVE IT TO ITS MOSTFORWARD POSITION. ABOUT 1/4INCH FARTHER FORWARD THAN THEFRAME.

PLACE RECOIL SPRING OVER STOPPOST AND DOWN INSIDE SLIDE.WHEN PLACING SPRING ROTATESPRING OVER POST UNTIL SPRINGWIRE END AT FRONT END OF SLIDE ISAT THE TOP.

15

Q~

~

~.

IF YOUR PISTOL DID NOTCOME WITH A THREE INCHBARREL USE YOUR OTHEREMPTY MAGAZINE ASSHOWN TO KEEP SPRING INPLACE WHILE RECOILINGSPRING.

IF YOUR PISTOL CAME WITHA THREE INCH BARREL USEIT AS SHOWN WHILE RECOIL-ING SPRING

WHILE HOLDING FRAME ANDCOMPONENT USED TO RE-COIL SPRING IN ONE GRIP.USE YOUR OTHER HAND TOPULL SLIDE COMPLETELY TOTHE REAR OF ITS STROKEAND ONCE THERE MOVESAFETY TO "SAFE".

REMOVE BARREL. RECOILSPRING SHOULD BE COM-PRESSED AND COILED ONSTOP POST. WITH THE SLIDELOCKED IN THE REARWARDPOSITION.

WHILE HOLDING THE SLIDEREARWARD ON THE FRAME.MOVE SAFETY TO "FIRE".

',\I ONLY ALLOW THE SLIDE TOMOVE FORWARD ABOUT1/8 OF AN INCH.

PLACE BARREL HOOK INFRAME OVER PIN AND RO-TATE DOWNWARD UNTIL ITLOCKS INTO PLACE.

CYCLE SLIDE BACK ANDFORTH TO PROPERLY SEATSPRING. IT IS NOT NECES-SARY TO PULL TRIGGER ORUN-COCK HAMMER WHILEATTEMPTING THIS.

SLIDE SHOULD MOVE BACKAND FORTH WITH OUT BIND-iNG. YOU SHOULD NOT BEABLE TO LIFT BARREL ENDUP IF BARREL IS SEATEDPROPERLY.

1.

LOCKING TRANSPORT CASEFOR TEMPORARY LIMITED ACCESS AND TRANSPORT ONLY. THIS IS NOT ASUBSTITUTE FOR A SAFE. ALL FIREARMS SHOULD BE KEPT IN A LOCKED SAFE WHENNOT UNDER YOUR CONTROl. AMMUNITION SHOULD ALWAYS BE STOREDSEPARATELY FROM PISTOl. ALWAYS CHECK FOR AN EMPTY CHAMBER BEFORESTORING OR TRANSPORTING.

HP CABLELANYARD

CLEANINGBRUSHES

CLEANING PATCHES

OIL BOTTLE

SPARE MAGAZINE

EXTRA BARREL

CARRY HANDLE

LATCH

UPPER LOCKMECHANISM

CLEANING ROD

EAR PLUGS

STORAGE FORHP 22/25 MODELPISTOLS ONLY

LOWER LOCKMECHANISM

2 KEYS

11

TURN RIGHT

~&j

~TO UNLOCK

BARRELS AND MAGAZINES

W236

~ym18

# NAME PRICE

205-.22 LR 3 INCH BARREL230-.22 LR STD. MAGAZINE236-.22 LR FOLLOWER237-.22 LR MAG SPRING238-.22 LR MAG BODY239-.22 LR STD. MAG BASE243- BASE LOCK270-.22 LR 5 INCH BARREL271 -.22 LR EXT. MAG BASE260...22 LR EXT. MAGAZINE305-.25 ACP 3 INCH BARREL330...25 ACP STD. MAGAZINE336-.25 ACP FOLLOWER337 -.25 ACP MAG SPRING338.25 ACP MAG BODY339.25 ACP STD. MAG BASE370.25 ACP 5 INCH BARREL371 .25 ACP EXT. MAG BASE360.25ACP EXT. MAGAZINE

19.5011.502.503.505.002.502.50

28.507.50

16.0019.5011.50

2.503.505.002.50

28.507.50

16.00

FRAME C OMPONENTS

21

19

# NAME PRICE201-FRAME NOT AVAILABLE207-MAGAZINE BUTTON 2.50208-SAFETY 4.50209-LEFT GRIP (PLASTIC) 5.0021 O-RIGHT GRIP (PLASTIC) 5.0021 1-MAG CATCH 2.5021 2-BARREL PIVOT PIN .7521 3TRIGGER PIVOT PIN .7521 4-DISCONNECTOR PIN .7521 6-SEAR PIN .75217 -TRIGGER 4.0021 8-HAMMER PIN 1.00219-DISCONNECTOR 2.90220-RECOIL SPRING 1.80222-SEAR SPRING .75223-CATCH SPRING .75224-TRIGGER SPRING .75227-STRUT SPRING 1.00228-GRIP SCREW (1) .50240-TRIGGER BAR PIN .75241-TRIGGER BAR 2.90242-BLOCK SPRING244-STOP POST 1.00247-EJECTOR 2.50248-STRUT 2.50249-CROSS PIN 1.00250-SAFETY BLOCK251-TAKE DOWN LEVER 4.50252-HAMMER 3.50

20

326- TRIGGER RETURN SPRING 1.00(NOT SHOWN)

SLIDE COMPONENTS

234

202

21

# NAME202-SLIDE203-EXTRACTOR204-FIRING PIN21 5-EXTRACTOR PIN221 -FIRING PIN SPRING226-EXTRACTOR SPRING229-SIGHT SPRING234-FRONTPLATE .22LR242-BLOCK SPRING245-SIGHT246-REAR PLATE253-FIRING PIN BLOCK254-REAR PLATE SCREW .40255-SIGHT SCREW .50

PRICE24.95

3.402.90

.75

.75.75.75

7.50

1.002.50

NOTES

PHOEN IX ARMS@ MODEL H P ACCESSORI ES

TAKE YOUR PHOENIX ARMS HP PISTOLS TO THE NEXT LEVEL WITH OUR NEW LINE OF

AFFORDABLE, HIGH QUALITY ACCESSORiES. EACH is DESIGNED TO IMPROVE AN ALREADY

SUPERB HANDGUN AND ADD TO YOUR SHOOTING ENJOYMENT.

HP LOCKING GUNTRANSPORT CASE

$14.00LOCKED GUN TRANSPORTCASE CAN BE KEYED THE

SAME AS THE PISTOLMAGAZINE WELL LOCK.

EXTENDED MAGAZINE$16.00

FOR LARGER HAND GRIP.lORD. CAPACITY.

STANDARD MAGAZINE$11.50

10 RD. CAPACITY.(NOT SHOWN)

H P PISTOL LOCK$12.00

INCLUDED WITH ALLPHOENIX ARMS MODELS.

INSTALLS IN MAGAZINE WELL.CUSTOM HPHARDWOOD

RESINATED GRIPS$18.00

HP NYLONBELT HOLSTER

$10.00WITH ADJUSTABLE WEB

STRAP. FITS EITHERLENGTH BARREL.

HP CLEANING KIT

$8.00COMES WITH ROD,

BREAKFREE "CLP" GUN OIL,BRUSH, JAG END, SLOTTED

END, PATCHES, SCREW

AND KNOB.

DESIGNS, MATERIALS AND PRICES SUBJECT TO CHANGE WITHOUT NOTICE.

DNO

DYES DNO

DYES DNO

DYES DNO

DETACH & MAIL YOUR LIFETIME WARRANTY

To ACTIVATE THIS WARRANTY YOU MUST COMPLETE THIS CARD AND MAIL, WITH PROPER

POSTAGE, WITHIN 30 DAYS OF PURCHASE.

MODEL DATE PURCHASED,SERIAL #,

1. WHERE DID YOU PURCHASE THIS PISTOL?

CITY, STATE, ZIP,

2. IS THIS YOUR FIRST PURCHASE OF A FIREARM? DYES

3. DID YOU RECEIVE THIS PISTOL IN A PHOENIX ARMS BOX WITH THE

OPERATING INSTRUCTIONS FOR THE PISTOL YOU PURCHASED?

4. DID YOU READ AND UNDERSTAND ALL OF THE OPERATING INSTRUCTIONS?

5. DID YOU RECEIVE ANY VERBAL INSTRUCTION FROM A COMPETENT

FIREARMS INSTRUCTOR ON THE SAFE HANDLING OF THIS PISTOL?

IF YOU ANSWER NO TO 4. OR S., IT IS OUR STRICT RECOMMENDATION FOR YOUR SAFETY, AND THE

SAFETY OF OTHERS, THAT YOU DO NOT ATTEMPT TO LOAD, OR OPERATE THIS PISTOL UNTIL YOU

HAVE OBTAINED SAFE HANDLING INSTRUCTIONS BY A QUALIFIED FIREARMS INSTRUCTOR!

NAME,

ADDRESS,

CITY, ZIP,STATE,

SIGNATURE,

ORDERING INFORMATION

CALL WITH MASTERCARDNISA OR SEND CHECK/MONEYORDER WITH $4.50 POSTAGE & HANDLING TO ADDRESSBELOW. BE SURE TO INCLUDE THE MODEL, FINISH, CALIBERAND SERIAL NUMBER WITH YOUR ORDER. DESIGNS ANDPRICES SUBJECT TO CHANGE WITHOUT NOTICE.

PHIEHIX1420 SOUTH ARCHIBALD AVE.

ONTARIO, CA 91761

909/937-6900

PHOEHIXWARRANTY DEPARTMENT

1420 SOUTH ARCHIBALD AVENUEONTARIO, CA 91761

PLACE

POSTAGE

HERE