Embed Size (px)
Citation preview
Prepared By- Mehul Joshi (Saudi Arebia ,Riyadh)
Its Prepare according Saudi Arabia coco sheet.
PAGE NO -2
In this page-Name-SITE NAMELocation- just Region name at where u workingDescription-depends on site configuration like(1+1+1),(2+2+2),(4+4+4).BTS ID- Site NameTRS- Follow coco sheet BTS- Here write MWAM IP(as per coco sheet)RNC- As per COCO SHEET Your TOP IP 10.247.64.18(just example).You have to change only last figure like 10.247.64.1 this IP address writeheresee carefully here u have to write 1 instead of 18 .Than other digit are same .Its your RNC IP address. NTP server- As per COCO SHEET Your TOP IP 10.247.64.18(just example.) You have to change only last figure like 10.247.64.4 this IP address write here. Just see carefully here you have to write 4 instead of 18 .Than other digit are same .Its your NTP server IP address.
PAGE NO -3
In this page
you have to write 10.247.254.6 .At any full IP site you have to write this IP its standard IP. It is not available in coco sheet. so u have to remember it.
than no need to change & clic next.
PAGE NO -5
In this page
Interface type- u have to select E1
Disable all the CRC.
Transport mode- here select lub IP
At last select 2nd number Autodetect. For this you have to just clic on 2nd number In use colume.
After completed this one your page as shown below.
Than clic Next.
PAGE NO -6
In this page no need to change. Than clic Next
PAGE NO -8
In this page clic at Transport Ethernet Interface . Than you see the page as
shown below.
In this page
Address- blank no need to fill up.
Total shaper information rate- 42.0(its standard)
Total shaper burst size-1522(its standard)
Committed information rate-7.0(its standard)
Than no need to change.
Than click at New VLAN This page as shown below.
In this page
VLAN ID- Follow COCO sheet
Address-Here write WBTS IP (As per COCO sheet)
Committed information rate-7.0(its standard)
Than click at Enable Qos.
Than clic at BFD session 1 in use
Session 1 destination address- here call to RNC & ask what is BFD IP for this site. He will give u BFD IP.This BFD IP write here.
Than no need to change
Than clic at VLAN mapping . This page is as shown below.
In this page see IP interface column & click one by one & select VLAN VLANID for example-VLAN 1646(here 1646 VLANID).
After complete this one Than click Next.
PAGE NO -9
In this page
Minimum UDP port- follow COCO sheet.
Than clic Next.
PAGE NO -10
In this page,
Far end SCTP subnet- Follow COCO sheet
Minimum SCTP port- Follow COCO sheet
Minimum UDP port- Follow COCO sheet
CAC commited bit rate- 7.0(its standard)
Signaling bit rate- Follow COCO sheet (1000 its standard)
DCN bit rate- Follow COCO sheet (100 its standard)
Than clic Next.
PAGE NO -11
In this page click at Timing over Packet in use.
Master clock address- Here write TOP IP (As per COCO sheet)
Than click Next.
PAGE NO -12
In this page in first row select Timing over Packet as shown in this page.
Than click Next.
PAGE NO -13
In this page
Default gateway- Here write Tallaps IP (As per COCO sheet)
Than click Next.
PAGE NO -20
In this page no need to change.
Than click Next.
PAGE NO -21
In this page
Configuration name- depends on site configuration like (1+1+1),
(2+2+2),(4+4+4).
Click at transmission synchronization (TDM/syncE/ToP) in use.
FSMD 2: Write here location
FSMD 3: Write here location
FSMD 4: Write here location
Than no need to change Click Next.
PAGE NO -22
In this page
Click at New Cell
See below Local cell & write there SITEID4 (for Example 5414 here SITEID-541) as shown in this page.
Than select FRGF1 ANT1 & FRGF2 ANT1 as shown in this page.
Than again click at New cell
See below Local cell & write there SITEID5(for Example 5415 here SITEID-541) as shown below page.
Than select FRGF1 ANT3 & FRGF2 ANT3 as shown below page.
Than again click at New cell
See below Local cell & write there SITEID6(for Example 5416 here SITEID-541) as shown below page.
Than select FRGF1 ANT5 & FRGF2 ANT5 as shown below page.
Than again click at New cell
See below Local cell & write there SITEID7(for Example 5417 here SITEID-541) as shown below page.
Than select FRGF1 ANT1 & FRGF2 ANT1 as shown below page.
Than again click at New cell
See below Local cell & write there SITEID8(for Example 5418 here SITEID-541) as shown below page.
Than select FRGF1 ANT3 & FRGF2 ANT3 as shown below page.
Than again click at New cell
See below Local cell & write there SITEID9(for Example 5419 here SITEID-541) as shown below page.
Than select FRGF1 ANT5 & FRGF2 ANT5 as shown below page.
Than click Next.
PAGE NO -23
In this page no need to change click Next.
PAGE NO -24
In this page
Fill UARFCN(UTRA Absolute Radio Frequency Channel Number ) column.
For local cell 4,5,6 use UARFCN-10673) (Its standard)
For local cell 7,8,9 use UARFCN-10648 (Its standard)
Than click Next.
PAGE NO -25
In this page no need to change.
Click Next.
PAGE NO -26
In this page no need to change.
Click Next.
PAGE NO -27
In this page no need to change.
Click Next.
PAGE NO -28
If you have data of feeder loss fill it. For this select one by one FRGF1 ANT1, FRGF1 ANT3,…………….. FRGF2 ANT5 & fill up feeder loss.
Click Next.
PAGE NO -31
In this page no need to change.
Click Next.
PAGE NO -33
In this page click at Send Parameters.
Commissioning is complete.
