MAKE: STYLE:

45

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITYFor more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY: MODERATE

MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 877.287.8634

Safety glasses should be worn at all times whileinstalling this product.

YEARS: 2020-PRESENT SUBARU MODEL: OUTBACK / LEGACY WAGON/SEDAN

4,000600

TRAILER WEIGHT:TONGUE WEIGHT:

13437 INSTALLATION INSTRUCTIONS

LBS.LBS.

90 MIN.MIN. PRO INSTALL TIME:

NOVICE INSTALL TIME:

IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

SCAN FORMORE INFO

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.For more information log onto www.curtmfg.comThis product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 3/13/2020

EASY

NO DRILLING

TRIM BUMPER COVER

SOCKET

14mm17mm

RATCHETTAPE

MEASURE

MASKINGTAPE

AVIATIONSHEARS

TORQUEWRENCH

SAFETYGLASSES

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com

Parts List

DESCRIPTIONPART NUMBERQTYITEM

HHCS,M10x1.25,30,CL10.9,YZ10-1027141

WASHER, S-CON,3/8,YZ30-0014842

TRUNK PAN

BUMPER BEAM

EXISTING VEHICLEHARDWARE (BOTH SIDES)1

2

1. Outback: Remove rear bumper underbody panel by removing (5) plastic push fasteners then pushing apart the clips inside the bumper cover. Set aside for reinstallation in Step 4. Legacy: Remove (9) plastic fasteners from the bottom of the bumper cover and (3) from each wheel well. Carefully remove bumper cover by pulling the sides off then pull straight back.

2. Remove (4) bolts and (2) nuts holding the bumper beam in place. Save the nuts for reinstallation in Step 3. Note: Bumper beam will be held up by vehicle studs on each side.

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com

3. Slide hitch into place between trunk pan and bumper beam. Loosely secure vehicle nuts removed in Step 2 and supplied M10 bolts with conical toothed washers. Torque hardware to 45 ft-lbs. Note: Installing outside driver side bolt first followed by outside passenger side bolt second may ease installation. Center fascia bracket may need to be bent during installation.

4. Trim bumper fascia using Trim Diagram below for reference and reinstall bumper cover removed in Step 1.

TRIM DIAGRAM

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

4,000 600

28

45

SUBARU OUTBACK / LEGACY3/13/202013437

90

Scanfor moreinformation

Parts ListDESCRIPTIONPART NUMBERQTYITEM

HHCS,M10x1.25,30,CL10.9,YZ10-1027141WASHER, S-CON,3/8,YZ30-0014842

TRUNK PAN

BUMPER BEAM

EXISTING VEHICLEHARDWARE (BOTH SIDES)

1

2

- NO DRILLING- TRIMMING REQUIRED

1. Outback: Remove rear bumper underbody panel by removing (5) plastic push fasteners then pushing apart the clips inside the bumper cover. Set aside for reinstallation in Step 5. Legacy: Remove (9) plastic fasteners from teh bottom of the bumper cover and (3) from each wheel well. Carefully remove bumper cover by pulling the sides off then pull straight back. Set aside for reinstallation in Step 5.

2. Remove (4) bolts and (2) nuts holding the bumper beam in place. Save the nuts for reinstallation in Step 3. Note: Bumper beam will be held up by vehicle studs on each side. 3. Slide hitch into place between trunk pan and bumper beam. Loosely secure with vehicle nuts removed in Step 2 and supplied M10 bolts with conical toothed washers.

4. Torque hardware to 45 ft-lbs.

5. Trim bumper fascia using Trim Diagram above for reference and reinstall bumper cover removed in Step 1.

TOOLS REQUIRED14mm & 17mm SOCKETS

RATCHETTAPE MEASUREMASKING TAPE

AVIATION SHEARSTORQUE WRENCHSAFETY GLASSES

TRIM DIAGRAM