View
458
Download
1
Embed Size (px)
DESCRIPTION
Citation preview
CEMproof® EasySealD
ece
mb
er
20
10
CEMproof® SilverSeal „active“
THE extra light, swelling, water-reactive, self healing waterproofing solution
De
cem
be
r 2
01
0
SilverSeal
De
cem
be
r 2
01
0
De
cem
be
r 2
01
0
Test result:EasySeal with a one side PE-coating
= SilverSeal
De
cem
be
r 2
01
0
Waterreactive selfhealing membranes!
Bentonit-Membrane vs Hydrophilic waterreactive swelling membrane
Bentonit 1h H2O 1d H2O 3d H2O 10d H2O
Bentonite
De
cem
be
r 2
01
0
EasySealH2O
Swelling Polymer
SAP,LDP – hydrophilic Polymers
Waterreactive selfhealing membranes!
Hydrophilic waterreactive swelling membrane
High quality Structural – waterproofing
CEMproof Geotextil waterprofing
De
cem
be
r 2
01
0
EasySeal could replace in the future all conventional waterproofing methods
used in civil engineering, such as bituminous materials, coatings and all kinds
of synthetic foils.
The combination of EasySeal and synthetic foils (PVC, TPO, HDPE, EPDM a.s.o.)
is the solution for a high waterproofing quality.
EasySeal in combination with a regular membrane will be the
EasySeal / SilverSeal swelling nonwoven
De
cem
be
r 2
01
0
EasySeal in combination with a regular membrane will be the
innovative sealing technology of the near future.
The self healing properties of the swelling, hydrophilic polyacrylates secure
the integrity of the system in cases where the regular membrane is damaged
during installation. Penetrating water causes the polyacrylates to swell and
makes the whole system impermeable. The building structure is permanently
protected against penetrating water, even small cracks and voids in the
concrete are sealed.
SilverSeal® Installation Guidelines
SilverSeal®
De
cem
be
r 2
01
0
Place SilverSeal® over the properly prepared
concrete bedding / blinding concrete bed with
the white side facing the structural concrete to be
waterproofed!
Overlap all adjoining edges a minimum of 50mm and
glue the overlaps tight together with CEM 805
bonding agent.
The silver shining PE-membrane is the first water barrier.
SilverSeal® Installation Guidelines
- Structural concrete
- CEM805 for sealing and bonding
- SilverSeal®
- Blinding concrete bed / concrete bedding
- Natural soil
De
cem
be
r 2
01
0
SilverSeal® has to be placed with the open side facing the
structural/construction concrete!
The white side of SilverSeal® is hydrophilic and swells into
concrete cracks when water appears and avoids any water
circulation between SilverSeal® and the concrete structure!
- Natural soil
SilverSeal® Installation Guidelines
SilverSeal® can be applied to backfilled walls in two ways:
Mechanically fastening to cast concrete just prior to
backfilling (post-applied), or secondly (a not preferred
alternative), by utilizing the adhesion properties of the
De
cem
be
r 2
01
0
alternative), by utilizing the adhesion properties of the
SilverSeal® (preapplied).
Fix SilverSeal® by using approx. 1 up to 2 shot-fired
‘softwasher’ per square meter vertical wall.
SilverSeal® has to be installed always with the
open side (white side) facing to the concrete
which has to be sealed!
SilverSeal® is very easy to install, though the following instructions need to be considered:
Horizontal overlappings can easily be
secured with CEM 805 adhesive. Vertical
overlappings have to be glued with CEM
805 adhesive.
Overlappings should at least be 5 - 10 cm
and need to be mechanically fixed.
The contact pressure should not be less than
150 kg/m².
SilverSeal has to be installed with the open
(white) side facing to the concrete which
has to be sealed. The closed side (covered
with silver PE foil) faces the water side.
De
cem
be
r 2
01
0
SilverSeal can be mechanical fixing onto
the structural concrete by applying the
recommended fastener - SilverSeal can
be nailed through. The emerging holes
seal itself automatically +
reliable/waterproof
SilverSeal swelling non-woven can be
inserted into the formwork/mold. Due to
the interconnection to
the fresh concrete SilverSeal adheres to
the wall.
When penetrations through SilverSeal are
necessary it should be left open and leak
proof sealed with CEM 805 /
CEM 805 “active“.
Heads of bore piles must permanently be
sealed with crystalline CEMdicht 3 in 1.
Waterproofing Technology for:
by using CEMproof® SilverSeal „active“,
the new needle punched
swelling non-woven
Structural Waterproofing
De
cem
be
r 2
01
0
EasySeal / SilverSeal swelling nonwoven
De
cem
be
r 2
01
0
EasySeal / SilverSeal swelling nonwoven
De
cem
be
r 2
01
0
The extra light weight swelling
non-woven
EasySeal / SilverSeal swelling nonwoven
De
cem
be
r 2
01
0
The new generation of active
membran-technology!
EasySeal / SilverSeal swelling nonwoven
De
cem
be
r 2
01
0
EasySeal & SilverSeal swelling nonwoven
thank you for your attention and hope to further impress
you soon!
De
cem
be
r 2
01
0