Namazu the patterned sheets to make the model. Part one · 2018-07-11 · 23 19 22 18 24 20 Body section complete. Fold the upper corner down. Open up part one by folding the upper

32 4

Fold the upper edges in to the middle crease. Then unfold.

Note the alignment of the pattern behind.

Fold the upper corner down to the middle of the square.

Fold and unfold the square in half along all axes. Then

turn the paper over.

Fold the square in half diagonally.

Fold the corner back. This is a “fold and unfold” step

shown with a double arrow.

65

9 10

Fold the upper corner over the adjacent folded

edges and unfold.

Fold the corner back again.

Unfold the edges folded in step 10.

Fold the edges in diagonally to touch the

middle crease.

Fold one side over (a) at the same time fold out the paper in the upper folded

triangle (b).

Fold the corner back over.

8

12

(a)

(b)

Fold the side over and fold out the adjacent paper.

(Repeating step 6).

1

11

7

NamazuPart oneNamazu is a two piece model. Cut out

the patterned sheets to make the model.

© 2010 - 2018 SQUARE ENIX CO., LTD. All Rights Reserved. LOGO ILLUSTRATION:©2010 YOSHITAKA AMANO. NOT FOR SALE.STORMBLOOD, HEAVENSWARD and A REALM REBORN are registered trademarks or trademarks of Square Enix Co., Ltd.

FINAL FANTASY, FINAL FANTASY XIV, FFXIV, SQUARE ENIX and the SQUARE ENIX logo are registered trademarks or trademarks of Square Enix Holdings Co., Ltd.

Diagrams © 2018 Creaselightning Limited www.creaselightning.co.uk

23

19

22

18

24

20

Fold the side back.

Fold the side back.

Fold the upper and lower edges to the middle and

unfold.

Fold the upper and lower edges to the middle and

unfold.

Fold in the edge (one layer) diagonally to touch the

outer edge. Then unfold.

Fold in the edge (one layer) diagonally to touch the

outer edge. Then unfold.

Fold the opposite side over.

Fold and unfold the square in half diagonally.

Fold in half lengthwise.

2625

29 30

Fold up the upper layer. This will cause the paper

behind to fold in.

Fold the front corner up. Fold in progress.Check the inner folded corners indicated are folded as shown.

then fold the corner back.

Fold the outer corners in. The creases should through

the crease intersections.

28

32

Fold the upper corner down and fold the corners

in.

21

17

31

27

13 1514 16

Fold the upper edge up causing the edges to fold

in.

Fold and unfold the edges lengthwise along the middle of the upper square section.

Turn the model over left to right.


Rotate the model 180°.

180°




3938 40

Fold the edge (folded in step 42) back again.

Fold the corner up to the edge and unfold.

Repeat steps 42 to 44 on the other side.

Fold the inner point up. .Separate the layers of the upper corner and open the

point and squash it flat.

Fold the top layer up along the upper edge, causing the

outer edges to fold in.

Fold one side over to expose the inner section.

Fold the section back down.

4645

49 50

Fold the edges of the mid section behind. The upper

section will reverse.

Fold the edges of the points behind to narrow

them.

Part one complete.Fold the lower corners of the face behind to shape it.

Reverses the corners inside the upper squashed

point.

Reverse fold the points, turning them inside out.

48

52

Fold the edges down to narrow the points.

37

51

47

4342 4441

33 3534 36

Repeat steps 31 to 33.Fold the edge back again. Fold the upper corner down.

(31-33)

(42-44)






3

(a) (a)(b)

2 4

Fold the upper layers in. The outer corners will

fold inside.

Fold the corners out to touch the outer edge.

(a) Fold and unfold the outer corners. (b)Then

make two diagonal folds and unfold.

Complete steps 1 to 9 of Part One on the second

square.

Fold the corner up to the middle.

65

9 10

Fold the upper edge over, open the model and fold the upper section down.

Turn the model over and rotate slightly.

Fold the upper down to touch the edge indicated.

Fold the model in half.

8

12

13 1514 16

Fold the Lower corner up to stand perpendicular.

Then squash it flat.

1

11

Fold the lower corners back again.

7

Fold the lower corners out beneath the upper section.

Fold over one side. Fold the side back and reverse fold the lower

section.

(1-9)



Part TwoNamazu




23

19

22

18

24

20

Body section complete.

Fold the upper corner down.

Open up part one by folding the upper layer up.

Fold the outer edges to the middle.

Repeat steps 15 to 16 on the other side.

Crease the edges and fold the edges back out.

Fold the upper corners down and fold the lower

corners in.

2625

29 30

Fold lower corner up.Fold the edges behind and tuck them behind

the inner edge.

Pinch the edges together to fold the tail down.

Fold the outer edges of the upper section out.

Put the body inside and refold the edges behind

the lower diamond.

28

32

33 3534 36

Fold the upper section down.

21

17

31

27

Fold the edges of the legs in.

Fold the edges of the face in and curl the whiskers.

Namazu complete.Use the tail to support the

model





Assembly Parts one and two




NamazuPart one

Namazu is a two piece model. Cut out the patterned sheets to make the model.




NamazuPart Two

Namazu is a two piece model. Cut out the patterned sheets to make the model.




Documents

Namazu the patterned sheets to make the model. Part one · 2018-07-11 · 23 19 22 18 24 20 Body section complete. Fold the upper corner down. Open up part one by folding the upper