MPS-200e-drum set

assembly instructions

Musikhaus Thomann e.K.

Treppendorf 30

96138 Burgebrach

Germany

Telephone: +49 (0) 9546 9223-0

E-mail: info@thomann.de

Internet: www.thomann.de

06.06.2013

Table of contents

1 Safety instructions.......................................................................................................................................................................................................... 4

2 Contents of package....................................................................................................................................................................................................... 5

3 Assembly.............................................................................................................................................................................................................................. 6

4 Protecting the environment.................................................................................................................................................................................... 12

Table of contents

MPS-200

3

1 Safety instructions

DANGER!

Danger for childrenEnsure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.Choking hazard!

Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces andchoke!

Never let children unattended use electrical devices.

Safety instructions

e-drum set

4

2 Contents of package

Before you assemble your kit, make sure the contents of package is complete according to the following list.

Millenium MPS-200 e-drum special set

n Millenium e-drum modulen Pads:

4 × snare / tom1 × bass drum3 × cymbals / hi-hat

n Hi-hat pedaln Drum pedaln Rack with pad bracketsn Complete pad wiringn Mains adapter

Contents of package

MPS-200

5

3 Assembly

Assembling the rack

CAUTION!

Danger of cuts on hands and fingersWhen plugging the connections, take care for sharp edges on the metal pipes, screws etc.

Loosen the screws of each terminal before inserting the pipes. Mount the various elements in the specified sequence. The posi‐tions of the pads, cymbals, etc. are shown in the illustration below.

Assembly

e-drum set

6

Connect the left side pipe (mainstay L) to the left base and tighten the allen screw of the terminal with the supplied drum key.Stabilise the unit with a crossbar (see figure). Then connect the right side pipe (mainstay R) to the right base and tighten the allenscrew of the terminal with the supplied drum key. Stabilise the unit with a crossbar (see figure).

Connect the top terminals of the left and right mainstay using the crossbeam of the rack and tighten the allen screws of theterminals firmly using the supplied drum key. Then stabilise the unit with a crossbar (see figure).

Assembly

MPS-200

7

Connect the top left side arm (L1) to the second terminal and the lower left side arm (L2) to the third terminal of the left sidepanel. Tighten the allen screws of the terminals firmly with the supplied drum key. Then connect the right side arm (R) to thesecond terminal of the right side panel and tighten the allen screws of the terminals firmly with the supplied drum key.

Assembly

e-drum set

8

Mounting pads on the rack

Attach the supplied L-pieces to the pads. Tighten the wing nuts on the pads by hand first. Then slide the plastic ends of the L-pieces up to the stop into the designated terminals on the rack (see figure). Align the pads on the rack to meet your needs, thentighten the wing nuts of the pad brackets and the bolts of the retaining terminals on the rack firmly and evenly.

Mounting cymbals on the rack

Assembly

MPS-200

9

Put the cymbal holders into the designated terminals on the rack (see figure) and tighten the allen screws of the terminals firmlywith the supplied drum key.

Unscrew the wing nuts from the cymbal holders and take the felt washers off the holders. Place the cymbals as shown in thefigure on the holders. Then place the felt washers on the cymbals and fix the cymbals with the associated wing nuts on theholders.

Mounting the drum module on the rack

Attach the supplied L-piece to the drum module. Tighten the wing screw of the module hand-tight first. Then slide the plastic endof the L-piece up to the stop into the designated terminal on the left side arm of the rack (see figure). Align the module on therack according to your needs and tighten the wing nut on the module as well as the screw of the pad clamp on the rack firmlyand evenly.

Assembly

e-drum set

10

Kick drum pedal and pad

Snap the two metal rods into the holes provided on the frame of the kick drum pedal. Place the beater into the hole provided onthe rotary head of the pedal and tighten the terminal.

Attach the drum pedal with the two screws on the bass drum pad and attach the beater to the pedal (see figure).

Then mount the support device and place the bass drum pad centred under the rack. Position the pedal centred in front of thepad.

Setting up and wiring

Set up the rack, the pads and the cymbals according to your needs. As a final step, all triggers need to be wired to the drummodule. Note the labelling on the drum module and the colour markings of each cable.

Assembly

MPS-200

11

4 Protecting the environment

Disposal of the packaging material

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normalrecycling.

Ensure that plastic bags, packaging, etc. are properly disposed of.

Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling.Please follow the notes and markings on the packaging.

Disposal of your old device

This device is subject to the European directive 2002/96/EC.

Do not dispose of the device with your normal household waste.

Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device,comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

Protecting the environment

e-drum set

12

Notes

MPS-200

13

Notes

e-drum set

14

Musikhaus Thomann e.K. · Treppendorf 30 · 96138 Burgebrach · Germany · www.thomann.de