cellularAssembly instructionsDesign: Archirivolto

Thank you for buying a quality Brunner product from the cellular series. The versatile lounge furniture in our cellular range is perfect if you are looking to furnish small quiet areas and workspaces in large halls and waiting areas. Available with or without panel, these versatile chairs and benches can be used in a myriad of ways.

Thanks to the 60° angled construction of the work and lounging units, they can be set out in groups, lines or circles, making best use of available space. Side tables that can be flexibly positioned make for the ideal addition to the range.

If upholstered easy chairs, work tables or standing tables are ordered with panel, the panel have to be mounted on site. These assembly instructions provide an explanation of all of the key components and will help you to assemble your cellular lounge furniture with ease.

CELLULAR ASSEMBLY INSTRUCTIONS

Contents

4

5

7

10

11

14141414

1515

Lounge elements with panel

Scope of delivery of upholstered furniture with panel Assembly instructions for upholstered easy chair and panel

Scope of delivery of work table/standing table with panel

Assembly instructions for work table/standing table with panel

Further informationGeneral information about assemblyRecommended assembly toolCare instructions

NoteImprint

LOUNGE ELEMENTS WITH PANEL

Lounge elements with panel | Scope of delivery of upholstered easy chair with panel 4 . 5

SCOPE OF DELIVERY OF UPHOLSTERED EASY CHAIR WITH PANEL

Included in scope of delivery:

12X 5X30 Spax screws 4X brackets

1X M5x35 screw 4X M5x16 screws

1X left-hand 1X right-handpanel panel

1X chair

ASSEMBLY INSTRUCTIONS FOR UPHOLSTERED EASY CHAIR WITH PANEL

ASSEMBLY STEP 1Hook the right-hand panel into the pre-assembled fixture on the right-hand side on the back of the upholstered easy chair, taking care not to press down.

ASSEMBLY STEP 2Then, hook the left-hand panel into the corresponding fixture on the left-hand side on the back of the upholstered easy chair, again taking care not to press down.

ASSEMBLY INSTRUCTIONS FOR UPHOLSTERED EASY CHAIR WITH PANEL

Assembly instructions for upholstered easy chair with panel 6. 7

ASSEMBLY STEP 3Gently push the top edges of the two panel apart and position the M5x35 screw in the corresponding thread in the left-hand panel. Tighten the screw accordingly.

ASSEMBLY STEP 4Lift the right-hand panel up slightly and hook the screw from the left-hand panel into the recess in the right-hand panel to attach them to one another.

ASSEMBLY INSTRUCTIONS FOR UPHOLSTERED EASY CHAIR WITH PANEL

ASSEMBLY STEP 5Now push the two panel down so they are locked into position in the fixtures on the upholstered easy chair.

ASSEMBLY STEP 6Carefully tip the upholstered easy chair back together with the panel and place the furniture on a soft and clean surface, such as a blanket. Position the four brackets at the recommended points between the lower edge of the upholstery and the panel. Fix in position on the panel using an M5x16 screw.

Assembly instructions for upholstered easy chair with panel 8. 9

ASSEMBLY STEP 7Push the panel to the side of the upholstered easy chair and align the bracket with the chair. Fasten the four brackets to the base of the upholstered easy chair using three 5x30 Spax screws for each. Make sure the first panel is fastened before moving on to the second panel.

ASSEMBLY INSTRUCTIONS FOR UPHOLSTERED EASY CHAIR WITH PANEL

SCOPE OF DELIVERY OF WORK TABLE AND STANDING TABLE WITH PANEL

Included in scope of delivery:

4x m5x40 screw 6x m5x20 screws

1x m5x35 screw 2x cable channels for electrification

1x left-hand 1x right-handpanel panel

1x standing or 1x tabletable

Assembly instructions for work table and standing table with panel 10. 11

ASSEMBLY STEP 1Place the right-hand panel on a soft and clean surface, such as a blanket, and position the work table or standing table on top on its side. Align the frame with the top two screw-on points on the panel and fix in position on the panel using two M5x40 screws.

ASSEMBLY STEP 2Fasten the three fixing lugs on the two table legs to the panel using M5x20 screws.

ASSEMBLY INSTRUCTIONS FOR WORK TABLE AND STANDING TABLE WITH PANEL

ASSEMBLY STEP 3Position the M5x35 screw in the corresponding thread in the left-hand panel and tighten the screw accordingly. Now follow assembly steps 1 and 2 again to assemble the left-hand panel.

With cable channel

ASSEMBLY INSTRUCTIONS FOR WORK TABLE AND STANDING TABLE WITH PANEL

Without cable channel

ASSEMBLY STEP 4Turn the table over carefully and place it on its legs. If you have ordered a cable channel, follow the instructions provided in assembly step 5.

Assembly instructions for work table and standing table with panel 12. 13

ASSEMBLY STEP 5To fasten the optional cable channel, simply hang the two strips along the rear table leg at the back on the right and left.

ASSEMBLY INSTRUCTIONS FOR WORK TABLE AND STANDING TABLE WITH PANEL

FURTHER INFORMATION

GENERAL INFORMATION ABOUT ASSEMBLY

The assembly instructions provide general guidelines for assembling your cellular furniture· The steps described are to be followed for all cellular chairs and tables· The assembly tools suggested are simply recommendations from Brunner GmbH· Only the materials supplied may be used for assembly· Brunner GmbH accepts no liability for damage caused during assembly

ASSEMBLY TOOL FOR CELLULAR FURNITURE

Cordless screwdriver with hexagon and cross insert

CARE INSTRUCTIONS – POWDER-COATED BASES

For normal use, it is sufficient to wipe the powder-coated surfaces with a clean, soft, slightly damp cloth. Any particularly dirty areas can be cleaned with a standard, grease-dissolving all-purpose cleaner. However, abrasive cleaning agents and toilet or sanitary cleaners must not be used because they may damage the powder-coated surface. Acid or alkaline cleaning agents and organic solvents must also not be used. Please only use soft cotton cloths for cleaning purposes and never use plastic sponges, wire wool or steam jet devices, which could permanently damage the surface. The gliders' surfaces should be regularly cleaned to remove coarse pieces of dirt or deposits.

CARE INSTRUCTIONS – COVER FABRICS AND LEATHER

Cover fabrics should be regularly vacuumed with a soft attachment. We recommend following the cleaning and care instructions of the material manufacturer to remove stains and dirt deposits. During normal use, it is sufficient to wipe the leather covers with a dry or slightly damp cloth. If dirt has dried on, the best way to clean the area is with a weak neutral soap solution and a soft cloth. Then remove the soap suds with a damp cloth. The leather cover must never be treated with standard cleaning agents (washing-up liquid, all-purpose cleaner etc.) because they will irreversibly damage the leather sur-face (impregnation/glaze). Solvents, cleaning petrol, stain removers, spirit, shoe cream etc. must also not be used. We offer an appropriate care kit for cleaning your leather covers.

Notes

For details, prices, terms and conditions, refer to the current price list. We reserve the right to technical changes, errors and colour deviations. Some models are displayed as special versions that are subject to additional costs.

Imprint

Product design:

Archirivolto

Illustrations:

Andreas Stapel . Brunner GmbH

Text:

Kerstin Lamprecht . Hanne Haaf . Brunner GmbH

Design:

Kerstin Lamprecht . Brunner GmbH

05 |

2017

www.brunner-group.com© Brunner GmbH 2017 . Im Salmenkopf 10 . 77866 Rheinau, GermanyT. +49 78 44 40 20 . F. +49 78 44 40 28 00 . info@brunner-group.com