Page 1 of 12939504856 Rev L

Montage® Enhanced and Monolithic Tile Assembly®

If you have a problem, question, or request, callyour local dealer, or Steelcase Line 1 at888.STEELCASE (888.783.3522)for immediate action by people who want to help you.

(Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500)Or visit our website: www.steelcase.com© 2005 Steelcase Inc. Grand Rapids, MI 49501 U.S.A.

Printed in U.S.A.

Flat Tool - ZFTE

Enhanced Tiles

Monolithic Tiles

Page 2 of 12939504856 Rev L

1

2

3

TILE TOP

TILE BOTTOM

TILE BOTTOM

MONOLITHIC WOOD TILES HAVE�MIDDLE CLIPS THAT ARE�INSTALLED INTO THESE HOLES.

MONOLITHIC TACKABLE ACOUSTICAL�TILES HAVE MIDDLE CLIPS THAT ARE�INSTALLED INTO THESE HOLES.

Page 3 of 12939504856 Rev L

4 5

6

Page 4 of 12939504856 Rev L

Termination Tile with Decora or Nema Cutout Option

NOTE: Installation and removal are the same as non-tackable tile shown on pages 2 & 3.

Termination Tilewith Decora Cutout

6 location options shown.

Termination Tilewith Nema Cutout

6 location options shown.

Page 5 of 12939504856 Rev L

1

2

3

For Glass Tiles manufactured after May 31, 2010 refer to assembly direction 939504871. ��Montage Glass Cleaning Process�

Montage glass should be cleaned inside and out thoroughly prior to installation. Care needs to be exercised in handling/installing the glass after it has been cleaned, especially the surface that will end up on the interior of the frame. For product that is currently installed, the glass needs to be disassembled for internal cleaning as a portion of the interior glass is unaccessible against the frame.

Process:Place the glass tiles on a grounded surface so that no static charges get built up during the cleaning process. An ergonomically designed bench or worksurface area is ideal so that installers do not have to bend over. Avoid laying glass on carpet surfaces as the fibers may create static charges.

Spray Glass cleaner on windows or glass surfaces and then wipe it off with untreated paper towels, or lint-free cotton cloths for a streak-free shine. (for example Windex® and Kimberly Clark Professional Wypall X70 Kimtowels).

Clean the glass out of direct sunlight. Sunlight can heat up windows causing sprays to dry before you can wipe them clean. If you can't control the drips try spraying the cloth first then wiping. The last step should be a dry pass, use dry clean paper towels, or lint-free cotton cloth.

Page 6 of 12939504856 Rev L

5

6

WARNING:DO NOT OVERTIGHTEN SCREWS.

4a

4b

4c

These holes added to standard frames (aluminum beams) by drilling .156 (5/32") holes.

NOTE: Make sure the top clip assemblies�have been inserted onto the�back of the glass.

Side View of a�Conversion Clip for�

mounting a Enhanced Glass�Tile to a Standard Frame

Side View of a�Standard Clip to�

a Standard Frame

For Glass Tiles manufactured after May 31, 2010 refer to assembly direction 939504871. ��Glass Tile Installation (continued)

Page 7 of 12939504856 Rev L

7

8

9

For Glass Tiles manufactured after May 31, 2010 refer to assembly direction 939504871. ��Glass Tile Installation (continued)

Page 8 of 12939504856 Rev L

Slatwall Tile Installation

CAUTION:To ensure proper installation use only the attachment screws provided. Failure to do so may result in personal injury.

Warning:DO NOT OVERTIGHTEN SCREWS.

1a

2

a b

To Open

Ensure latches (a and b), at each end, are open.

View from back

Obround opening

These holes must be added to standard frames (aluminum beams) by drilling .156" (5/32") dia. holes.

1b

Page 9 of 12939504856 Rev L

Slatwall Tile Installation (continued)

3 Install. 4 Using ZFTE tool, slide latch tooutside to lock tile in place.�Repeat with latch at other end.�(Access latch from bottom of�obround opening.)

5 Repeat step 4 but slide both latches to theinside to unlock the tile.Lift (at bottom) and rotate tile away from panel.

Slatwall Tile Removal

Page 10 of 12939504856 Rev L

For Slatwall Tiles that were manufactured before March 1, 2005 this�modification needs to be made on the backside of a slatwall because�of a screw head interference on the lower horizontal filler strip.

1 2

Option #1

1. Remove tiles from frame.

2. Remove the lower horizontal filler strip.

20"H (Stack-on)

45"H (Base Frame)

NOTE: A horizontal filler strip is not�needed between the base frame�and stack-on frame.

NOTE: Horizontal filler strip must be�added to the enhanced monolithic�frame in each location where tile�segmentation occurs.

HORIZONTAL FILLER STRIP

HORIZONTAL FILLER STRIP

Page 11 of 12939504856 Rev L

3b

3. Turn the lower horizontal filler strip upside down (3a) and re-attach to frame (3b).

4. Re-attach panels and install slatwall.

4

3a

Note: Tile segmentation anda desk-height cavity is required for desk-height power and data access. Tiles cannot be field-cut.

Tip: Horizontal filler strips must be added in each location where tile segmentation occurs. A filler strip is not needed between the desk-height cavity cover and the13"H tile above.

HORIZONTAL FILLER STRIP

HORIZONTAL FILLER STRIP

Page 12 of 12939504856 Rev L

Option #2

1. Remove the rib on the back of the slatwall by grinding away at the locations where the interference with the screw heads occur.

2. Install slatwall.

2

RIB

1