Modul 04 Spur Gear Design using AGMA
Upload
others
View
24
Download
4
Embed Size (px)
344 x 292
429 x 357
514 x 422
599 x 487
Citation preview
PowerPoint PresentationTeknik Mesin - FTMD ITB
MS3111 - Elemen Mesin
Modul 04 Spur Gear Design using AGMA
IntroductionsSegment 1
3 MS3111 Elemen Mesin MAK © 2021
Teknik Mesin - FTMD ITB
MS3111 - Elemen Mesin
and Calculation Methods for Involute Spur and
Helical Gear Teeth
Basic Concept
≥
≥ ,
Fundamental Formula Bending Stress
where for U.S. customary units (SI units), is the tangential
transmitted load, lbf (N)
0 is the overload factor
is the dynamic factor
is the size factor
is the transverse diametral pitch
is the face width of the narrower member, in (mm)
is the load-distribution factor
is the rim-thickness factor
is the geometry factor for bending strength (which includes root
fillet
stress-concentration factor ) is the transverse metric module
7 MS3111 Elemen Mesin MAK © 2021
Factor of Safety Bending Stress
Metric unit:
where for U.S. customary units (SI units), is the allowable bending
stress, lbf/in2 (N/mm2)
is the stress cycle factor for bending stress
are the temperature factors
are the reliability factors
is the AGMA factor of safety, a stress ratio =
Metric unit:
where , 0, , , , , , are the same terms as previous.
= 0 1
For U.S. customary units (SI units), the additional terms
are:
is an elastic coefficient,
is the surface condition factor
1 is the pitch diameter of the pinion, in (mm)
is the geometry factor for pitting resistance
9 MS3111 Elemen Mesin MAK © 2021
Factor of Safety Pitting resistance (contact Stress)
Metric unit:
where for U.S. customary units (SI units), is the allowable contact
stress, lbf/in2 (N/mm2)
is the stress cycle life factor
are the hardness ratio factors for pitting resistance
are the temperature factors
are the reliability factors
is the AGMA factor of safety, a stress ratio
, =
Un-crowned GearsCrowned Gears
2
11 MS3111 Elemen Mesin MAK © 2021
Crowning is the removal of a slight amount of the tooth from the
center on out to the reach edge, making the tooth surface slightly
convex. This method allows the gear to maintain contact in the
central region of the tooth and permits avoidance of edge contact.
Crowning should not be larger than necessary as it will reduce the
tooth contact area, thus weakening the gears strength. End relief
is the chamfering of both ends of tooth surface.
Crowning of Gear
Formula for Bending Stress
Formula for Wear
Teknik Mesin - FTMD ITB
MS3111 - Elemen Mesin
=
Transmitted Load,
Metric unit:
= 60000
where: Wt = transmitted load, kN H = power, kW d = gear diameter,
mm n = speed, rev/min
=
US Customary unit:
where: Wt = transmitted load, lbf H = power, hp V = pitch-line
velocity, ft/min
19 MS3111 Elemen Mesin MAK © 2021
Overload factors: 0 The overload factor K0 is intended to make
allowance for all externally applied loads in excess of the nominal
tangential load in a particular application. These factors are
established after considerable field experience in a particular
application.
=
20 MS3111 Elemen Mesin MAK © 2021
Dynamic factor: Dynamic factors are used to account for
inaccuracies in the manufacture and meshing of gear teeth in
action. Transmission error is defined as the departure from uniform
angular velocity of the gear pair. Some of the effects that produce
transmission error are:
• Inaccuracies produced in the generation of the tooth profile;
these include errors in tooth spacing, profile lead, and
runout
• Vibration of the tooth during meshing due to the tooth
stiffness
• Magnitude of the pitch-line velocity
• Dynamic unbalance of the rotating members
• Wear and permanent deformation of contacting portions of the
teeth
• Gear shaft misalignment and the linear and angular deflection of
the shaft
• Tooth friction
=
Transmission accuracy level number: Quality number
• 3 – 7: most commercial-quality gears • 8 – 12: precision quality
gears
=
where:
The maximum velocity*):
=
Dynamic factor:
22 MS3111 Elemen Mesin MAK © 2021
Figure 14–9 Dynamic factor . The equations to these curves
Dynamic factor:
23 MS3111 Elemen Mesin MAK © 2021
Size factor: The size factor reflects nonuniformity of material
properties due to size. It depends upon
• Tooth size • Diameter of part • Ratio of tooth size to diameter
of part • Face width • Area of stress pattern • Ratio of case depth
to tooth size • Hardenability and heat treatment
= 1
= 1
= 1.192
Metric unit:
Lewis Form Factor: Y
Transverse Diametral Pitch,
= =
Face width of the narrower member,
For Spur Gear: For Helical Gear:
Face width, F
27 MS3111 Elemen Mesin MAK © 2021
Load-distribution factor: The load-distribution factor modified the
stress equations to reflect nonuniform distribution of load across
the line of contact. The ideal is to locate the gear “midspan”
between two bearings at the zero slope place when the load is
applied. However, this is not always possible. The following
procedure is applicable to
• Net face width to pinion pitch diameter ratio F/d ≤ 2
• Gear elements mounted between the bearings
• Face widths up to 40 in
• Contact, when loaded, across the full width of the narrowest
member
=
The load-distribution factor modified the stress equations to
reflect nonuniform distribution of load across the line of contact.
The ideal is to locate the gear “midspan” between two bearings at
the zero-slope place when the load is applied. However, this is not
always possible. The following procedure is applicable to: • Net
face width to pinion pitch diameter ratio Τ ≤ 2 • Gear elements
mounted between the bearings • Face widths up to 40 in • Contact,
when loaded, across the full width of the narrowest member
29 MS3111 Elemen Mesin MAK © 2021
Load-distribution factor: = = 1 + +
=
The load-distribution factor under these conditions is currently
given by
the face load distribution factor,
30 MS3111 Elemen Mesin MAK © 2021
Load-distribution factor: =
Figure 14–10 Definition of distances S and S1 used in evaluating
Cpm
Table 14–9 Empirical Constants A, B, and C for Eq. (14–34), Face
Width F in Inches∗
31 MS3111 Elemen Mesin MAK © 2021
Load-distribution factor: =
32 MS3111 Elemen Mesin MAK © 2021
Rim-thickness factor: When the rim thickness is not sufficient to
provide full support for the tooth root, the location of bending
fatigue failure may be through the gear rim rather than at the
tooth fillet.
=
Bending-strength geometry factor,
The AGMA factor J employs a modified value of the Lewis form
factor, also denoted by Y; a fatigue stress-concentration factor Kf
; and a tooth load-sharing ratio mN . The resulting equation for
for spur and helical gears is
=
It is important to note that the form factor in this Eq is not the
Lewis factor at all. The value of Y here is obtained from
calculations within AGMA 908-B89, and is often based on the highest
point of single-tooth contact.
34 MS3111 Elemen Mesin MAK © 2021
Bending-strength geometry factor: J =
35 MS3111 Elemen Mesin MAK © 2021
AGMA 908-B89 Geometry Factors for Determining the Pitting
Resistance and Bending Strength of Spur, Helical and Herringbone
Gear Teeth
=
36 MS3111 Elemen Mesin MAK © 2021
AGMA 908-B89 Geometry Factors for Determining the Pitting
Resistance and Bending Strength of Spur, Helical and Herringbone
Gear Teeth
=
37 MS3111 Elemen Mesin MAK © 2021
AGMA 908-B89 Geometry Factors for Determining the Pitting
Resistance and Bending Strength of Spur, Helical and Herringbone
Gear Teeth
=
38 MS3111 Elemen Mesin MAK © 2021
AGMA 908-B89 Geometry Factors for Determining the Pitting
Resistance and Bending Strength of Spur, Helical and Herringbone
Gear Teeth
=
39 MS3111 Elemen Mesin MAK © 2021
AGMA 908-B89 Geometry Factors for Determining the Pitting
Resistance and Bending Strength of Spur, Helical and Herringbone
Gear Teeth
=
Gear bending endurance strength equation or bending factor of
safety
41 MS3111 Elemen Mesin MAK © 2021
Bending strength: The values for gear bending strength, designated
here as , are to be found in Figs. 14–2, 14–3, and 14–4, and in
Tables 14–3 and 14–4. Since gear strengths are not identified with
other strengths such as Sut , Se, or Sy as used elsewhere in this
book, their use should be restricted to gear problems.
When two-way (reversed) loading occurs, as with idler gears, AGMA
recommends using 70 percent of values. This is equivalent to Τ1
0.70 = . as a value of . The recommendation falls between the value
of = 1.33 for a Goodman failure locus and = 1.66 for a Gerber
failure locus.
42 MS3111 Elemen Mesin MAK © 2021
=
Figure 14–2 Allowable bending stress number for through- hardened
steels.
Bending strength:
Bending strength: =
Nitrided through-hardened steel gears
Figure 14–3 Allowable bending stress number for nitrided through-
hardened steel gears
= 0.569 + 83.8
44 MS3111 Elemen Mesin MAK © 2021
Bending strength: =
Figure 14–4 Allowable bending stress numbers for nitriding steel
gears St .
nitriding steel gears
=
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
48 MS3111 Elemen Mesin MAK © 2021
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
49 MS3111 Elemen Mesin MAK © 2021
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
50 MS3111 Elemen Mesin MAK © 2021
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
51 MS3111 Elemen Mesin MAK © 2021
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
52 MS3111 Elemen Mesin MAK © 2021
ANSI/AGMA 2001--D04 Fundamental Rating Factors and Calculation
Methods for Involute Spur and Helical Gear Teeth
53 MS3111 Elemen Mesin MAK © 2021
Stress-cycle factors: The AGMA strengths are based on 107 load
cycles applied. The purpose of the load cycle factors YN and ZN is
to modify the gear strength for lives other than 107 cycles. • Note
that for 107 cycles YN = ZN = 1 on each graph. • Note also that the
equations for YN and ZN change on either side of 107
cycles. For life goals slightly higher than 107 cycles, the mating
gear may be experiencing fewer than 107 cycles and the equations
for (YN )P and (YN)G
can be different.
=
Stress-cycle factors: =
Figure 14–14 Repeatedly applied bending strength stress-cycle
factor .
55 MS3111 Elemen Mesin MAK © 2021
Bending Safety Factor,
= Τ
The ANSI/AGMA standards 2001-D04 and 2101-D04 contain a safety
factors: • guarding against bending fatigue failure and • guarding
against pitting failure.
=
Temperature factor:
For oil or gear-blank temperatures up to 250°F (120°C), use KT = Y
= 1.0. For higher temperatures, the factor should be greater than
unity. Heat exchangers may be used to ensure that operating
temperatures are considerably below this value, as is desirable for
the lubricant.
=1 For T < 120 °C ( 250 °F)
=
Reliability factor:
The reliability factor accounts for the effect of the statistical
distributions of material fatigue failures.
=
Teknik Mesin - FTMD ITB
MS3111 - Elemen Mesin
= 0
Τ1 2
60 MS3111 Elemen Mesin MAK © 2021
Elastic coefficient: Values of Cp may be computed directly from Eq.
(14–13) or obtained from Table 14–8.
=
Transmitted Load,
Metric unit:
= 60000
where: Wt = transmitted load, kN H = power, kW d = gear diameter,
mm n = speed, rev/min
= 33000
US Customary unit: where: Wt = transmitted load, lbf H = power, hp
V = pitch-line velocity, ft/min
=
62 MS3111 Elemen Mesin MAK © 2021
Overload factors: 0 The overload factor K0 is intended to make
allowance for all externally applied loads in excess of the nominal
tangential load in a particular application. These factors are
established after considerable field experience in a particular
application.
=
63 MS3111 Elemen Mesin MAK © 2021
Dynamic factor: Dynamic factors are used to account for
inaccuracies in the manufacture and meshing of gear teeth in
action. Transmission error is defined as the departure from uniform
angular velocity of the gear pair. Some of the effects that produce
transmission error are:
• Inaccuracies produced in the generation of the tooth profile;
these include errors in tooth spacing, profile lead, and
runout
• Vibration of the tooth during meshing due to the tooth
stiffness
• Magnitude of the pitch-line velocity
• Dynamic unbalance of the rotating members
• Wear and permanent deformation of contacting portions of the
teeth
• Gear shaft misalignment and the linear and angular deflection of
the shaft
• Tooth friction
Transmission accuracy level number: Quality number
• 3 – 7: most commercial-quality gears • 8 – 12: precision quality
gears
=
where:
The maximum velocity*):
=
Dynamic factor: =
65 MS3111 Elemen Mesin MAK © 2021
Figure 14–9 Dynamic factor . The equations to these curves
Dynamic factor: =
66 MS3111 Elemen Mesin MAK © 2021
Size factor: The size factor reflects nonuniformity of material
properties due to size. It depends upon
• Tooth size • Diameter of part • Ratio of tooth size to diameter
of part • Face width • Area of stress pattern • Ratio of case depth
to tooth size • Hardenability and heat treatment
= 1 = 1
Lewis Form Factor: Y
68 MS3111 Elemen Mesin MAK © 2021
Load-distribution factor: The load-distribution factor modified the
stress equations to reflect nonuniform distribution of load across
the line of contact. The ideal is to locate the gear “midspan”
between two bearings at the zero slope place when the load is
applied. However, this is not always possible. The following
procedure is applicable to
• Net face width to pinion pitch diameter ratio F/d ≤ 2
• Gear elements mounted between the bearings
• Face widths up to 40 in
• Contact, when loaded, across the full width of the narrowest
member
=
Load-distribution factor:
The load-distribution factor modified the stress equations to
reflect nonuniform distribution of load across the line of contact.
The ideal is to locate the gear “midspan” between two bearings at
the zero-slope place when the load is applied. However, this is not
always possible. The following procedure is applicable to: • Net
face width to pinion pitch diameter ratio Τ ≤ 2 • Gear elements
mounted between the bearings • Face widths up to 40 in • Contact,
when loaded, across the full width of the narrowest member
=
Load-distribution factor:
The load-distribution factor under these conditions is currently
given by
the face load distribution factor,
=
Load-distribution factor:
Figure 14–10 Definition of distances S and S1 used in evaluating
Cpm
Table 14–9 Empirical Constants A, B, and C for Eq. (14–34), Face
Width F in Inches∗
=
Pitch diameter of Pinion,
For Spur Gear: For Helical Gear:
=
Face width of the narrower member,
For Spur Gear: For Helical Gear:
Face width, F
=
Surface Condition Factor, =
Τ
The surface condition factor or is used only in the pitting
resistance equation. It depends on:
• Surface finish as affected by, but not limited to, cutting,
shaving, lapping, grinding, shot-peening
• Residual stress • Plastic effects (work hardening)
Standard surface conditions for gear teeth have not yet been
established. When a detrimental surface finish effect is known to
exist, AGMA specifies
a value of greater than unity. For now: = . .
76 MS3111 Elemen Mesin MAK © 2021
Surface-Strength Geometry factor: =
Τ
The factor is also called the pitting-resistance geometry factor by
AGMA.
=
The load-sharing ratio,
The load-sharing ratio is equal to the face width divided by the
minimum total length of the lines of contact. This factor depends
on:
• the transverse contact ratio , • the face-contact ratio , • the
effects of any profile modifications, and • the tooth
deflection.
=
For spur gears: = 0
where: is the axial pitch is the face width.
78 MS3111 Elemen Mesin MAK © 2021
The load-sharing ratio,
For helical gears having a face-contact ratio > 2.0, a
conservative approximation is given by the equation: =
0.95
= cos where is the normal circular pitch.
= + 2 − 2 Τ1 2
+ + 2 − 2 Τ1 2
− + sin
= cos
where and are the pitch radii and and the base-circle radii of the
pinion and gear, respectively
where is the normal base pitch and is the length of the line of
action in the transverse plane.
79 MS3111 Elemen Mesin MAK © 2021
GEAR CONTACT ENDURANCE STRENGTH EQUATION OR WEAR FACTOR OF
SAFETY
, =
, = The allowable contact stress,
The values for the allowable contact stress, designated here as ,
are to be found in Fig. 14–5 and Tables 14–5, 14–6, and 14–7. AGMA
allowable stress numbers (strengths) for bending and contact stress
are for:
• Unidirectional loading • 10 million stress cycles (107 cycles) •
99 percent reliability
81 MS3111 Elemen Mesin MAK © 2021
, = The allowable contact stress,
Figure 14–5 Contact-fatigue strength at 107 cycles and 0.99
reliability for through-hardened steel gears.
through-hardened steel gears.
A ll o
A ll o
Stress-cycle factors:
The AGMA strengths are based on 107 load cycles applied. The
purpose of the load cycle factors YN and ZN is to modify the gear
strength for lives other than 107 cycles.
• Note that for 107 cycles YN = ZN = 1 on each graph. • Note also
that the equations for YN and ZN change on either side of 107
cycles. For life goals slightly higher than 107 cycles, the mating
gear may be experiencing fewer than 107 cycles and the equations
for (YN )P and (YN)G
can be different.
, =
Stress-cycle factors: , =
86 MS3111 Elemen Mesin MAK © 2021
Hardness-ratio factor: The pinion generally has a smaller number of
teeth than the gear and consequently is subjected to more cycles of
contact stress. If both the pinion and the gear are
through-hardened, then a uniform surface strength can be obtained
by making the pinion harder than the gear. A similar effect can be
obtained when a surface-hardened pinion is mated with a through
hardened gear. The hardness-ratio factor CH is used only for the
gear.
= 1.0 + − 1.0
, =
− 8.29 10−3
, =
88 MS3111 Elemen Mesin MAK © 2021
Hardness-ratio factor: When surface-hardened pinions with hardness
of 48 Rockwell C scale (Rockwell C 48) or harder are run with
through-hardened gears (180–400 Brinell), a work hardening occurs.
The factor is a function of pinion surface finish and the mating
gear hardness.
= 1.0 + 450 − where: ′ = 0.0075 exp −0.0112 and is the surface
finish of the pinion expressed as root-mean-square
roughness in in.
, =
, =
90 MS3111 Elemen Mesin MAK © 2021
Pitting Safety Factor,
= Τ
The ANSI/AGMA standards 2001-D04 and 2101-D04 contain a safety
factors: • guarding against bending fatigue failure and • guarding
against pitting failure.
=
Τ1 2
Temperature factor:
For oil or gear-blank temperatures up to 250°F (120°C), use KT = Y
= 1.0. For higher temperatures, the factor should be greater than
unity. Heat exchangers may be used to ensure that operating
temperatures are considerably below this value, as is desirable for
the lubricant.
=1 For T < 120 °C ( 250 °F)
, =
Reliability factor:
The reliability factor accounts for the effect of the statistical
distributions of material fatigue failures.
, =
Thank You Lecturers
Institut Teknologi Bandung
Modul 04 Spur Gear Design using AGMA
LOAD MORE