Embed Size (px)
Citation preview
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
11
Metric Series Timing Belts
High Power Metric Belts (page 13)RPP Silver Belts provide increased torque and power capacity.Available 8mm (8S) and 14mm (14S) pitches, they operate onstandard metric pulleys to transmit up to 470kW. Body of thebelt is manufactured from reinforced polychloropreniccompound with exceptional resistance to flex fatigue, ozone,heat, and mineral oils. The teeth are faced with graphiteimpregnated nylon for high strength and low friction. A highmodule resistant fibre cord gives high breaking strength withreduced elasticity.
As with classical series belts, power is transmitted by a glassfibre tension member spirally wound across the width of thebelt. The glass fibre cord ensures length stability combinedwith high strength and resistance to failure under repeatedflexing. The tension member is bonded into a syntheticrubber body moulded integral with the drive teeth. Therubber compound selected has complete absence of agedeformation and high resistance to mineral lubricating oils,heat, ozone and flex fatigue. A tough nylon fabric is bondedto the drive face of the belt, which by a patented treatment isself lubricating, for low coefficient of friction with exceptionalresistance to abrasion and shear, for high drive efficiency withlong belt and pulley life.
Standard Metric Belts (pages 12)The RPP series of belts provide the ideal solution for mostdrives. Totally interchangeable with other deep profile belts,they are available in 4 pitch sizes; 3mm (3M), 5mm (5M); 8mm(8M), and 14mm (14M). Standard drives are suitable forapplications from fractional kW up to 250kW power rating.In order to transmit higher powers tooth contact between beltand pulley has to be increased. To achieve this a parabolictooth form with contact angle increasing from tooth base totip was adopted, enabling a deeper tooth form than classicalbelts. The improved level of meshing, combined withsmoother engagement of drive, increased resistance to toothshear and tooth jumping enabled higher torque transmissionwith reduced installation tension. Belts have an indentation atthe top of the tooth to further improve meshing between beltand pulley by deformation of the tooth tip allowing precisemoulding of tooth to pulley contours, reducing frictional wear.The indentation also allows air to escape, further reducingnoise levels.
Standard High Torque Metric Timing Belt DrivesTo provide optimum performance with a standard range ofMetric High Torque Drive Pulleys, Cross & Morse selected.RPP series belts.The RPP belts are, combined with a standard range of pulleyto provide “off the shelf” drives in 4 pitches; 3mm (3M) 5mm(5M), 8mm (8M), and 14mm (14M), able to transmit up to700kW, or drive shafts to 15,000 r.p.m.
The pulleys are available with 2 methods of shaft connection;Pilot bored, pages 17-20, for finishing with sized bore, keywayand setscrews can, optionally be supplied finished; taperbored for fitting standard taper bushes page 25.
For even higher powered drives, up to 700kW, the Pantherseries belts, were developed in 8mm (8G) and 14mm (14G)pitches. These use Aramid reinforced polychloroprene for thebody of the belt with double layer graphite impregnatednylon facing for the teeth. The tension cables are in Kevlar formaximum strength with flexibility. The belts provide all theadvantages of RPP Silver with additional load capacity,excellent anti-static properties, and ability to use idlers on theback of the belt.
Anti Static BeltsBelts conforming to BS2050 standards can be supplied for the8M and 14M belt sizes. These belts are for appliction within chemical plants, oil refineries, and in mines.
The RPP Silver & RPP Gold high power belts have anti-staticproperties as standard.
Double sided Belts (page 15)To enable power to be taken from both sides of the belt totransfer direction of drive. Available in 5M and 14M toothform to operate on standard Metric pulleys.
These belts have moulded teeth on both sides with nylonjacket, to enable full torque transmission. Ideal for Serpentinedrives, and multi shaft arrangements.
‘TIL’ Long length BeltsSpecial manufacturing method enables extra long lengthendless belts to be manufactured.
Ideal for long centre distance drives where full torquetransmission is required.
Open Ended Metric Belts (pages 26-28)Long length (up to 150 Metres) open ended belts are availablein both standard neoprene rubber costruction, and inPolyurethane with RPP tooth form.For increased Power capacity the “Green Belt” is available asan alternate/replacement, these being Polyurethane beltsmanufactured to tight tolerance with standard RPP toothprofile for maximum power transmission.
The teeth are faced with green nylon fabric giving reducednoise and friction. High strength steel tension member giveshigh breaking strengths with extremely low elongation. Thebelts are available in 5mm, 8mm, and 14mm pitch for lineardrive applications, and are particularly suitable in drives withfrequent speed change.
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 11
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
535565575580600610615635640670675700705710725740750755800835850890900935940
BeltLength
mmNo.
Teeth
9mm Wide Belt 15mm Wide Belt 25mm Wide Belt
Cat. No. Cat. No. Cat. No.
535-5M9565-5M9575-5M9580-5M9600-5M9610-5M9615-5M9635-5M9640-5M9670-5M9675-5M9700-5M9705-5M9710-5M9725-5M9740-5M9750-5M9755-5M9800-5M9835-5M9850-5M9890-5M9900-5M9935-5M9940-5M9
107113115116120122123127128134135140141142145148150151160167170178180187188
22242424252626272728282930303031313234353637383939
535-5M15565-5M15575-5M15580-5M15600-5M15610-5M15615-5M15635-5M15640-5M15670-5M15675-5M15700-5M15705-5M15710-5M15725-5M15740-5M15750-5M15755-5M15800-5M15835-5M15850-5M15890-5M15900-5M15935-5M15940-5M15
37404041424343444547474949505152525356586062636566
535-5M25565-5M25575-5M25580-5M25600-5M25610-5M25615-5M25635-5M25640-5M25670-5M25675-5M25700-5M25705-5M25710-5M25725-5M25740-5M25750-5M25755-5M25800-5M25835-5M25850-5M25890-5M25900-5M25935-5M25940-5M25
636667687071727475787982828385878788949899104106109110
Wtgms
Wtgms
Wtgms
90-3M15105-3M15129-3M15141-3M15144-3M15147-3M15150-3M15159-3M15168-3M15174-3M15177-3M15180-3M15186-3M15195-3M15201-3M15204-3M15210-3M15213-3M15225-3M15231-3M15240-3M15243-3M15246-3M15252-3M15255-3M15261-3M15264-3M15267-3M15270-3M15
89
1010111111121213131414151617181819191920202122
Metric Series Timing Belts
5mm Pitch Standard Metric Belts Type 5MBelt
Lengthmm
No.Teeth
9mm Wide Belt 15mm Wide Belt 25mm Wide Belt
Cat. No. Cat. No. Cat. No.
180225235245255265270285295300305325345350375400420425450455460465475500525
3645474951535457596061656970758084859091929395100105
180-5M9225-5M9235-5M9245-5M9255-5M9265-5M9270-5M9285-5M9295-5M9300-5M9305-5M9325-5M9345-5M9350-5M9375-5M9400-5M9420-5M9425-5M9450-5M9455-5M9460-5M9465-5M9475-5M9500-5M9525-5M9
13161617181919202121212324252628293032323233333537
180-5M15225-5M15235-5M15245-5M15255-5M15265-5M15270-5M15285-5M15295-5M15300-5M15305-5M15325-5M15345-5M15350-5M15375-5M15400-5M15420-5M15425-5M15450-5M15455-5M15460-5M15465-5M15475-5M15500-5M15525-5M15
180-5M25225-5M25235-5M25245-5M25255-5M25265-5M25270-5M25285-5M25295-5M25300-5M25305-5M25325-5M25345-5M25350-5M25375-5M25400-5M25420-5M25425-5M25450-5M25455-5M25460-5M25465-5M25475-5M25500-5M25525-5M25
3mm Pitch Standard Metric Belts Type 3MBelt
Lengthmm
No.Teeth
6mm Wide Belt 9mm Wide Belt 15mm Wide Belt
Cat. No. Wt gms Cat. No. Cat. No.
90105129141144147150159168174177180186195201204210213225231240243246252255261264267270
3035434748495053565859606265676870717577808182848587888990
22333333344444444455555555566
90-3M6105-3M6129-3M6141-3M6144-3M6147-3M6150-3M6159-3M6168-3M6174-3M6177-3M6180-3M6186-3M6195-3M6201-3M6204-3M6210-3M6213-3M6225-3M6231-3M6240-3M6243-3M6246-3M6252-3M6255-3M6261-3M6264-3M6267-3M6270-3M6
33444555555666666777788888888
557778889999
1010101111111212121313131313141414
90-3M9105-3M9129-3M9141-3M9144-3M9147-3M9150-3M9159-3M9168-3M9174-3M9177-3M9180-3M9186-3M9195-3M9201-3M9204-3M9210-3M9213-3M9225-3M9231-3M9240-3M9243-3M9246-3M9252-3M9255-3M9261-3M9264-3M9267-3M9270-3M9
Wt gms
Wt gms
Wtgms
Wtgms
510-3M15513-3M15522-3M15531-3M15537-3M15564-3M15570-3M15576-3M15579-3M15597-3M15600-3M15633-3M15648-3M15669-3M15711-3M15735-3M15738-3M15756-3M15804-3M15882-3M15945-3M15
1062-3M151125-3M151245-3M151263-3M151500-3M151530-3M151863-3M15
No.Teeth
6mm Wide Belt 9mm Wide Belt 15mm Wide Belt
Cat. No. Wt gms Cat. No. Cat. No.
510513522531537564570576579597600633648669711735738756804882945
1062112512451263150015301863
170171174177179188190192193199200211216223237245246252268294315354375415421500510621
11111111111212121212121313141515151617181922232626313238
510-3M6513-3M6522-3M6531-3M6537-3M6564-3M6570-3M6576-3M6579-3M6597-3M6600-3M6633-3M6648-3M6669-3M6711-3M6735-3M6738-3M6756-3M6804-3M6882-3M6945-3M6
1062-3M61125-3M61245-3M61263-3M61500-3M61530-3M61863-3M6
16161616171718181818192020212223232325272933353839464758
26262727282929303031313333343738383941454955586465777996
Wt gms
Wt gms
510-3M9513-3M9522-3M9531-3M9537-3M9564-3M9570-3M9576-3M9579-3M9597-3M9600-3M9633-3M9648-3M9669-3M9711-3M9735-3M9738-3M9756-3M9804-3M9882-3M9945-3M9
1062-3M91125-3M91245-3M91263-3M91500-3M91530-3M91863-3M9
BeltLength
mm
BeltLength
mmNo.
Teeth
6mm Wide Belt 9mm Wide Belt 15mm Wide Belt
Cat. No. Wt gms Cat. No. Cat. No.
276285288291297300312318327330336339345357363375384390393405420432447474480486489501
9295969799
100104106109110112113115119121125128130131135140144149158160162163167
666666677777777888889991010101010
276-3M6285-3M6288-3M6291-3M6297-3M6300-3M6312-3M6318-3M6327-3M6330-3M6336-3M6339-3M6345-3M6357-3M6363-3M6375-3M6384-3M6390-3M6393-3M6405-3M6420-3M6432-3M6447-3M6474-3M6480-3M6486-3M6489-3M6501-3M6
99999910101010101011111112121212131313141515151515
14151515151516161717171718181919202020212222232425252526
Wt gms
Wt gms
276-3M9285-3M9288-3M9291-3M9297-3M9300-3M9312-3M9318-3M9327-3M9330-3M9336-3M9339-3M9345-3M9357-3M9363-3M9375-3M9384-3M9390-3M9393-3M9405-3M9420-3M9432-3M9447-3M9474-3M9480-3M9486-3M9489-3M9501-3M9
276-3M15285-3M15288-3M15291-3M15297-3M15300-3M15312-3M15318-3M15327-3M15330-3M15336-3M15339-3M15345-3M15357-3M15363-3M15375-3M15384-3M15390-3M15393-3M15405-3M15420-3M15432-3M15447-3M15474-3M15480-3M15486-3M15489-3M15501-3M15
25mm Wide BeltNo.Teeth
9mm Wide Belt 15mm Wide Belt
Cat. No. Cat. No. Cat. No.
950-5M9980-5M9
1000-5M91025-5M91050-5M91100-5M91125-5M91135-5M91195-5M91200-5M91240-5M91270-5M91420-5M91595-5M91690-5M91790-5M91800-5M91870-5M91895-5M91945-5M92000-5M92250-5M92525-5M9
190196200205210220225227239240248254284319338358360374379389400450505
40414243444647485050525360674175767980828495
106
950-5M15980-5M15
1000-5M151025-5M151050-5M151100-5M151125-5M151135-5M151195-5M151200-5M151240-5M151270-5M151420-5M151595-5M151690-5M151790-5M151800-5M151870-5M151895-5M151945-5M152000-5M152250-5M152525-5M15
67697072747779798484878999
112118125126131133136140158177
950-5M25980-5M25
1000-5M251025-5M251050-5M251100-5M251125-5M251135-5M251195-5M251200-5M251240-5M251270-5M251420-5M251595-5M251690-5M251790-5M251800-5M251870-5M251895-5M251945-5M252000-5M252250-5M252525-5M25
111115117120123129132133140140145149166187198209211219222228234263295
Wtgms
Wtgms
Wtgms
950980
100010251050110011251135119512001240127014201595169017901800187018951945200022502525
BeltLength
mmWtgms
21262729303132333535363840414447495053535454565961
12
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 12
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
8mm Pitch Standard Metric Belts Type 8MBelt
Lengthmm
No.Teeth
20mm Wide Belt 30mm Wide Belt 50mm Wide Belt
Cat. No. Wt kg Cat. No. Wt kg Cat. No. Wt kg
288320352360384408456480536544560600608632640680720800840880896920960
288-8M20320-8M20352-8M20360-8M20384-8M20408-8M20456-8M20480-8M20536-8M20544-8M20560-8M20600-8M20608-8M20632-8M20640-8M20680-8M20720-8M20800-8M20840-8M20880-8M20896-8M20920-8M20960-8M20
3640444548515760676870757679808590
100105110112115120
0.0330.0360.0400.0410.0430.0460.0520.0540.0610.0610.0630.0680.0690.0710.0720.0770.0810.0900.0950.0990.1010.1040.108
288-8M30320-8M30352-8M30360-8M30384-8M30408-8M30456-8M30480-8M30536-8M30544-8M30560-8M30600-8M30608-8M30632-8M30640-8M30680-8M30720-8M30800-8M30840-8M30880-8M30896-8M30920-8M30960-8M30
0.0490.0540.0600.0610.0650.0690.0770.0810.0910.0920.0950.1020.1030.1070.1080.1150.1220.1360.1420.1490.1520.1560.163
288-8M50320-8M50352-8M50360-8M50384-8M50408-8M50456-8M50480-8M50536-8M50544-8M50560-8M50600-8M50608-8M50632-8M50640-8M50680-8M50720-8M50800-8M50840-8M50880-8M50896-8M50920-8M50960-8M50
0.0810.0900.0990.1020.1080.1150.1290.1360.1510.1540.1580.1700.1720.1790.1810.1920.2030.2260.2370.2490.2530.2600.271
288-8M85320-8M85352-8M85360-8M85384-8M85408-8M85456-8M85480-8M85536-8M85544-8M85560-8M85600-8M85608-8M85632-8M85640-8M85680-8M85720-8M85800-8M85840-8M85880-8M85896-8M85920-8M85960-8M85
0.1380.1540.1690.1730.1840.1960.2190.2310.2570.2610.2690.2880.2920.3040.3070.3270.3460.3840.4030.4230.4300.4420.461
85mm Wide Belt
Cat. No. Wt kg
BeltLength
mmNo.
Teeth
20mm Wide Belt 30mm Wide Belt 50mm Wide Belt
Cat. No. Wt kg Cat. No. Wt kg Cat. No. Wt kg
10001040108011201200122412801352144014641600176018002000220024002520260028003048328036004400
1000-8M201040-8M201080-8M201120-8M201200-8M201224-8M201280-8M201352-8M201440-8M201464-8M201600-8M201760-8M201800-8M202000-8M202200-8M202400-8M202520-8M202600-8M202800-8M203048-8M203280-8M203600-8M204400-8M20
125130135140150153160169180183200220225250275300315325350381410450550
0.1130.1180.1220.1270.1360.1380.1450.1530.1630.1650.1810.1990.2030.2260.2490.2710.2850.2940.3160.3440.3710.4070.497
1000-8M301040-8M301080-8M301120-8M301200-8M301224-8M301280-8M301352-8M301440-8M301464-8M301600-8M301760-8M301800-8M302000-8M302200-8M302400-8M302520-8M302600-8M302800-8M303048-8M303280-8M303600-8M304400-8M30
0.1700.1760.1830.1900.2030.2070.2170.2290.2440.2480.2710.2960.3050.3390.3730.4070.4270.4410.4750.5170.5560.6100.746
1000-8M501040-8M501080-8M501120-8M501200-8M501224-8M501280-8M501352-8M501440-8M501464-8M501600-8M501760-8M501800-8M502000-8M502200-8M502400-8M502520-8M502600-8M502800-8M503048-8M503280-8M503600-8M504400-8M50
0.2830.2940.3050.3160.3390.3460.3620.3820.4070.4140.4520.4970.5090.5650.6220.6780.7120.7350.7910.8610.9271.0171.243
1000-8M851040-8M851080-8M851120-8M851200-8M851224-8M851280-8M851352-8M851440-8M851464-8M851600-8M851760-8M851800-8M852000-8M852200-8M852400-8M852520-8M852600-8M852800-8M853048-8M853280-8M853600-8M854400-8M85
0.4800.4990.5190.5380.5760.5880.6150.6490.6920.7030.7680.8450.8640.9611.0571.1531.2101.2491.3451.4641.5751.7292.113
85mm Wide Belt
Cat. No. Wt kg
10001040108011201200122412801352144014641600176018002000220024002520260028003048328036004400
288320352360384408456480536544560600608632640680720800840880896920960
8mm Pitch RPP Silver High Power Belts Type 8SBelt
Lengthmm
No.Teeth
20mm Wide Belt
Cat. No. Wt kg
30mm Wide Belt
Cat. No. Wt kg
50mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
288-8S20320-8S20352-8S20360-8S20384-8S20408-8S20456-8S20480-8S20536-8S20544-8S20560-8S20600-8S20608-8S20632-8S20640-8S20680-8S20720-8S20800-8S20840-8S20880-8S20896-8S20920-8S20960-8S20
3640444548515760676870757679808590
100105110112115120
0.0330.0360.0400.0410.0430.0460.0520.0540.0610.0610.0630.0680.0690.0710.0720.0770.0810.0900.0950.0990.1010.1040.108
288-8S30320-8S30352-8S30360-8S30384-8S30408-8S30456-8S30480-8S30536-8S30544-8S30560-8S30600-8S30608-8S30632-8S30640-8S30680-8S30720-8S30800-8S30840-8S30880-8S30896-8S30920-8S30960-8S30
0.0490.0540.0600.0610.0650.0690.0770.0810.0910.0920.0950.1020.1030.1070.1080.1150.1220.1360.1420.1490.1520.1560.163
288-8S50320-8S50352-8S50360-8S50384-8S50408-8S50458-8S50480-8S50536-8S50544-8S50560-8S50600-8S50608-8S50632-8S50640-8S50680-8S50720-8S50800-8S50840-8S50880-8S50896-8S50920-8S50960-8S50
0.0810.0900.0990.1020.1080.1150.1290.1360.1510.1540.1580.1700.1720.1790.1810.1920.2030.2260.2370.2490.2530.2600.271
288-8S85320-8S85352-8S85360-8S85384-8S85408-8S85456-8S85480-8S85536-8S85544-8S85560-8S85600-8S85608-8S85632-8S85640-8S85680-8S85720-8S85800-8S85840-8S85880-8S85896-8S85920-8S85960-8S85
0.1360.1540.1690.1730.1840.1960.2190.2310.2570.2610.2690.2880.2920.3040.3070.3270.3460.3840.4030.4230.4300.4420.461
BeltLength
mmNo.
Teeth20mm Wide Belt
Cat. No. Wt kg
30mm Wide Belt
Cat. No. Wt kg
50mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
1000-8S201040-8S201080-8S201120-8S201200-8S201224-8S201280-8S201352-8S201440-8S201464-8S201600-8S201760-8S201800-8S202000-8S202200-8S202400-8S202520-8S202600-8S202800-8S203048-8S203280-8S203600-8S204400-8S20
125130135140150153160169180183200220225250275300315325350381410450550
0.1130.1180.1220.1270.1360.1380.1450.1530.1630.1650.1810.1990.2030.2260.2490.2710.2850.2940.3160.3440.3710.4070.497
1000-8S301040-8S301080-8S301120-8S301200-8S301224-8S301280-8S301352-8S301440-8S301464-8S301600-8S301760-8S301800-8S302000-8S302200-8S302400-8S302520-8S302600-8S302800-8S303048-8S303280-8S303600-8S304400-8S30
0.1700.1760.1830.1900.2030.2070.2170.2290.2440.2480.2710.2980.3050.3390.3730.4070.4270.4410.4750.5170.5560.6100.746
1000-8S501040-8S501080-8S501120-8S501200-8S501224-8S501280-8S501352-8S501440-8S501464-8S501600-8S501760-8S501800-8S502000-8S502200-8S502400-8S502520-8S502600-8S502800-8S503048-8S503280-8S503600-8S504400-8S50
0.2830.2940.3050.3160.3390.3460.3620.3820.4070.4140.4520.4970.5090.5650.6220.6780.7120.7350.7910.8610.9271.0171.243
1000-8S851040-8S851080-8S851120-8S851200-8S851224-8S851280-8S851352-8S851440-8S851464-8S851600-8S851760-8S851800-8S852000-8S852200-8S852400-8S852520-8S852600-8S852800-8S853048-8S853280-8S853600-8S854400-8S85
0.4800.4990.5190.5380.5760.5880.6150.6490.6920.7030.7680.8450.8640.9611.0571.1531.2101.2491.3451.4641.5751.7292.113
13
288320352360384408456480536544560600608632640680720800840880896920960
288-8G20320-8G20352-8G20360-8G20384-8G20408-8G20456-8G20480-8G20536-8G20544-8G20560-8G20600-8G20608-8G20632-8G20640-8G20680-8G20720-8G20800-8G20840-8G20880-8G20896-8G20920-8G20960-8G20
3640444548515760676870757679808590
100105110112115120
0.0330.0360.0400.0410.0430.0460.0520.0540.0610.0610.0630.0680.0690.0710.0720.0770.0810.0900.0950.0990.1010.1040.108
288-8G30320-8G30352-8G30360-8G30384-8G30408-8G30456-8G30480-8G30536-8G30544-8G30560-8G30600-8G30608-8G30632-8G30640-8G30680-8G30720-8G30800-8G30840-8G30880-8G30896-8G30920-8G30960-8G30
0.0490.0540.0600.0610.0650.0690.0770.0810.0910.0920.0950.1020.1030.1070.1080.1150.1220.1360.1420.1490.1520.1560.163
288-8G50320-8G50352-8G50360-8G50384-8G50408-8G50456-8G50480-8G50536-8G50544-8G50560-8G50600-8G50608-8G50632-8G50640-8G50680-8G50720-8G50800-8G50840-8G50880-8G50896-8G50920-8G50960-8G50
0.0810.0900.0990.1020.1080.1150.1290.1360.1510.1540.1580.1700.1720.1790.1810.1920.2030.2260.2370.2490.2530.2600.271
288-8G85320-8G85352-8G85360-8G85384-8G85408-8G85456-8G85480-8G85536-8G85544-8G85560-8G85600-8G85608-8G85632-8G85640-8G85680-8G85720-8G85800-8G85840-8G85880-8G85896-8G85920-8G85960-8G85
0.1380.1540.1690.1730.1840.1960.2190.2310.2570.2610.2690.2880.2920.3040.3070.3270.3460.3840.4030.4230.4300.4420.461
10001040108011201200122412801352144014641600176018002000220024002520260028003048328036004400
8mm Pitch Gold High Power Belts Type 8GBelt
Lengthmm
No.Teeth
20mm Wide Belt
Cat. No. Wt kg
30mm Wide Belt
Cat. No. Wt kg
50mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
BeltLength
mmNo.
Teeth20mm Wide Belt
Cat. No. Wt kg
30mm Wide Belt
Cat. No. Wt kg
50mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
1000-8G201040-8G201080-8G201120-8G201200-8G201224-8G201280-8G201352-8G201440-8G201464-8G201600-8G201760-8G201800-8G202000-8G202200-8G202400-8G202520-8G202600-8G202800-8G203048-8G203280-8G203600-8G204400-8G20
125130135140150153160169180183200220225250275300315325350381410450550
0.1130.1180.1220.1270.1360.1380.1450.1530.1630.1650.1810.1990.2030.2260.2490.2710.2850.2940.3160.3440.3710.4070.497
1000-8G301040-8G301080-8G301120-8G301200-8G301224-8G301280-8G301352-8G301440-8G301464-8G301600-8G301760-8G301800-8G302000-8G302200-8G302400-8G302520-8G302600-8G302800-8G303048-8G303280-8G303600-8G304400-8G30
0.1700.1760.1830.1900.2030.2070.2170.2290.2440.2480.2710.2980.3050.3390.3730.4070.4270.4410.4750.5170.5560.6100.746
1000-8G501040-8G501080-8G501120-8G501200-8G501224-8G501280-8G501352-8G501440-8G501464-8G501600-8G501760-8G501800-8G502000-8G502200-8G502400-8G502520-8G502600-8G502800-8G503048-8G503280-8G503600-8G504400-8G50
0.2830.2940.3050.3160.3390.3460.3620.3820.4070.4140.4520.4970.5090.5650.6220.6780.7120.7350.7910.8610.9271.0171.243
1000-8G851040-8G851080-8G851120-8G851200-8G851224-8G851280-8G851352-8G851440-8G851464-8G851600-8G851760-8G851800-8G852000-8G852200-8G852400-8G852520-8G852600-8G852800-8G853048-8G853280-8G853600-8G854400-8G85
0.4800.4990.5190.5380.5760.5880.6150.6490.6920.7030.7680.8450.8640.9611.0571.1531.2101.2491.3451.4641.5751.7292.113
High Power RPP Silver and RPP Gold BeltsThe improved design RPP Silver and RPP Gold Belts cantransmit higher torques whilst still operating on standard HTDpulleys. Replacing a standard metric belt with the equivalentRPP belt can enable up to 100% more torque transmission,whilst the equivalent RPP Gold belt provides up to 200% more.
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 13
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
14
14mm Pitch Standard Metric Belts Type 14MBelt
Lengthmm
No.Teeth
40mm Wide Belt 55mm Wide Belt 85mm Wide Belt
Cat. No. Wt kg Cat. No. Wt kg Cat. No. Wt kg
966994
10921106119012601288134414001442156816101764177818481890190419602100224023102380245025902660280031503360350038503920432645784956
966-14M40994-14M40
1092-14M401106-14M401190-14M401260-14M401288-14M401344-14M401400-14M401442-14M401568-14M401610-14M401764-14M401778-14M401848-14M401890-14M401904-14M401960-14M402100-14M402240-14M402310-14M402380-14M402450-14M402590-14M402660-14M402800-14M403150-14M403360-14M403500-14M403850-14M403920-14M404326-14M404578-14M404956-14M40
6971787985909296
100103112115126127132135136140150160165170175185190200225240250275280309327354
0.380.390.430.440.470.500.510.530.550.570.620.630.700.700.730.740.750.770.830.880.910.940.971.021.051.101.241.321.381.521.541.701.801.95
966-14M55994-14M55
1092-14M551106-14M551190-14M551260-14M551288-14M551344-14M551400-14M551442-14M551568-14M551610-14M551764-14M551778-14M551848-14M551890-14M551904-14M551960-14M552100-14M552240-14M552310-14M552380-14M552450-14M552590-14M552660-14M552800-14M553150-14M553360-14M553500-14M553850-14M553920-14M554326-14M554578-14M554956-14M55
0.520.540.590.600.640.680.700.730.760.780.850.870.960.961.001.021.031.061.141.211.251.291.331.401.441.521.711.821.902.092.122.342.482.68
966-14M85994-14M85
1092-14M851106-14M851190-14M851260-14M851288-14M851344-14M851400-14M851442-14M851568-14M551610-14M851764-14M851778-14M851848-14M851890-14M851904-14M851960-14M852100-14M852240-14M852310-14M852380-14M852450-14M852590-14M852660-14M852800-14M853150-14M853360-14M853500-14M853850-14M853920-14M854326-14M854578-14M854956-14M85
0.810.830.910.931.001.051.081.131.171.211.311.351.481.491.551.581.591.641.761.881.931.992.052.172.232.342.642.812.933.223.283.623.834.15
966-14M115994-14M115
1092-14M1151106-14M1151190-14M1151260-14M1151288-14M1151344-14M1151400-14M1151442-14M1151568-14M1151610-14M1151764-14M1151778-14M1151848-14M1151890-14M1151904-14M1151960-14M1152100-14M1152240-14M1152310-14M1152380-14M1152450-14M1152590-14M1152660-14M1152800-14M1153150-14M1153360-14M1153500-14M1153850-14M1153920-14M1154326-14M1154578-14M1154956-14M115
1.091.131.241.251.351.431.461.521.591.631.781.822.002.012.092.142.162.222.382.542.622.702.782.933.013.173.573.813.964.364.444.905.195.61
966-14M170994-14M170
1092-14M1701106-14M1701190-14M1701260-14M1701288-14M1701344-14M1701400-14M1701442-14M1701568-14M1701610-14M1701764-14M1701778-14M1701848-14M1701890-14M1701904-14M1701960-14M1702100-14M1702240-14M1702310-14M1702380-14M1702450-14M1702590-14M1702660-14M1702800-14M1703150-14M1703360-14M1703500-14M1703850-14M1703920-14M1704326-14M1704578-14M1704956-14M170
1.621.661.831.851.992.112.162.252.342.412.632.702.952.983.093.163.193.283.523.753.873.994.104.344.454.695.275.635.866.456.567.247.678.30
115mm Wide Belt 170mm Wide Belt
Cat. No. Wt kg Cat. No. Wt kg
1.091.131.241.251.351.431.461.521.591.631.781.822.002.012.092.142.162.222.382.542.622.702.782.933.013.173.573.813.964.364.444.905.195.61
966994
10921106119012601288134414001442156816101764177818481890190419602100224023102380245025902660280031503360350038503920432645784956
14mm Pitch RPP Silver High Power Belts Type 14SBelt
Lengthmm
No.Teeth
40mm Wide Belt
Cat. No. Wt kg
55mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
115mm Wide Belt 170mm Wide Belt
Cat. No. Wt kg
966-14S40994-14S40
1092-14S401106-14S401190-14S401260-14S401288-14S401344-14S401400-14S401442-14S401568-14S401610-14S401764-14S401778-14S401848-14S401890-14S401904-14S401960-14S402100-14S402240-14S402310-14S402380-14S402450-14S402590-14S402660-14S402800-14S403150-14S403360-14S403500-14S403850-14S403920-14S404326-14S404578-14S404956-14S40
6971787985909296
100103112115126127132135136140150160165170175185190200225240250275280309327354
0.380.390.430.440.470.500.510.530.550.570.620.630.700.700.730.740.750.770.830.880.910.940.971.021.051.101.241.321.381.521.541.701.801.95
966-14S55994-14S55
1092-14S551106-14S551190-14S551260-14S551288-14S551344-14S551400-14S551442-14S551568-14S551610-14S551764-14S551778-14S551848-14S551890-14S551904-14S551960-14S552100-14S552240-14S552310-14S552380-14S552450-14S552590-14S552660-14S552800-14S553150-14S553360-14S553500-14S553850-14S553920-14S554326-14S554578-14S554956-14S55
0.520.540.590.600.640.680.700.730.760.780.850.870.960.961.001.021.031.061.141.211.251.291.331.401.441.521.711.821.902.092.122.342.482.68
966-14S85994-14S85
1092-14S851106-14S851190-14S851260-14S851288-14S851344-14S851400-14S851442-14S851568-14S851610-14S851764-14S851778-14S851848-14S851890-14S851904-14S851960-14S852100-14S852240-14S852310-14S852380-14S852450-14S852590-14S852660-14S852800-14S853150-14S853360-14S853500-14S853850-14S853920-14S854326-14S854578-14S854956-14S85
0.810.830.910.931.001.051.081.131.171.211.311.351.481.491.551.581.591.641.761.881.931.992.052.172.232.342.642.812.933.223.283.623.834.15
966-14S115994-14S115
1092-14S1151106-14S1151190-14S1151260-14S1151288-14S1151344-14S1151400-14S1151442-14S1151568-14S1151610-14S1151764-14S1151778-14S1151848-14S1151890-14S1151904-14S1151960-14S1152100-14S1152240-14S1152310-14S1152380-14S1152450-14S1152590-14S1152660-14S1152800-14S1153150-14S1153360-14S1153500-14S1153850-14S1153920-14S1154326-14S1154578-14S1154956-14S115
Cat. No. Wt kg
966-14S170994-14S170
1092-14S1701106-14S1701190-14S1701260-14S1701288-14S1701344-14S1701400-14S1701442-14S1701568-14S1701610-14S1701764-14S1701778-14S1701848-14S1701890-14S1701904-14S1701960-14S1702100-14S1702240-14S1702310-14S1702380-14S1702450-14S1702590-14S1702660-14S1702800-14S1703150-14S1703360-14S1703500-14S1703850-14S1703920-14S1704326-14S1704578-14S1704956-14S170
1.621.661.831.851.992.112.162.252.342.412.632.702.952.983.093.163.193.283.523.753.873.994.104.344.454.695.275.635.866.456.567.247.678.30
966994
10921106119012601288134414001442156816101764177818481890190419602100224023102380245025902660280031503360350038503920432645784956
BeltLength
mmNo.
Teeth40mm Wide Belt
Cat. No. Wt kg
55mm Wide Belt
Cat. No. Wt kg
85mm Wide Belt
Cat. No. Wt kg
115mm Wide Belt 170mm Wide Belt
Cat. No. Wt kg
966-14G40994-14G40
1092-14G401106-14G401190-14G401260-14G401288-14G401344-14G401400-14G401442-14G401568-14G401610-14G401764-14G401778-14G401848-14G401890-14G401904-14G401960-14G402100-14G402240-14G402310-14G402380-14G402450-14G402590-14G402660-14G402800-14G403150-14G403360-14G403500-14G403850-14G403920-14G404326-14G404578-14G404956-14G40
6971787985909296100103112115126127132135136140150160165170175185190200225240250275280309327354
0.380.390.430.440.470.500.510.530.550.570.620.630.700.700.730.740.750.770.830.880.910.940.971.021.051.101.241.321.381.521.541.701.801.95
966-14G55994-14G55
1092-14G551106-14G551190-14G551260-14G551288-14G551344-14G551400-14G551442-14G551568-14G551610-14G551764-14G551778-14G551848-14G551890-14G551904-14G551960-14G552100-14G552240-14G552310-14G552380-14G552450-14G552590-14G552660-14G552800-14G553150-14G553360-14G553500-14G553850-14G553920-14G554326-14G554578-14G554956-14G55
0.520.540.590.600.640.680.700.730.760.780.850.870.960.961.001.021.031.061.141.211.251.291.331.401.441.521.711.821.902.092.122.342.482.68
966-14G85994-14G85
1092-14G851106-14G851190-14G851260-14G851288-14G851344-14G851400-14G851442-14G851568-14G851610-14G851764-14G851778-14G851848-14G851890-14G851904-14G851960-14G852100-14G852240-14G852310-14G852380-14G852450-14G852590-14G852660-14G852800-14G853150-14G853360-14G853500-14G853850-14G853920-14G854326-14G854578-14G854956-14G85
0.810.830.910.931.001.051.081.131.171.211.311.351.481.491.551.581.591.641.761.881.931.992.052.172.232.342.642.812.933.223.283.623.834.15
966-14G115994-14G115
1092-14G1151106-14G1151190-14G1151260-14G1151288-14G1151344-14G1151400-14G1151442-14G1151568-14G1151610-14G1151764-14G1151778-14G1151848-14G1151890-14G1151904-14G1151960-14G1152100-14G1152240-14G1152310-14G1152380-14G1152450-14G1152590-14G1152660-14G1152800-14G1153150-14G1153360-14G1153500-14G1153850-14G1153920-14G1154326-14G1154578-14G1154956-14G115
1.091.131.241.251.351.431.461.521.591.631.781.822.002.012.092.142.162.222.382.542.622.702.782.933.013.173.573.813.964.364.444.905.195.61
966-14G170994-14G170
1092-14G1701106-14G1701190-14G1701260-14G1701288-14G1701344-14G1701400-14G1701442-14G1701568-14G1701610-14G1701764-14G1701778-14G1701848-14G1701890-14G1701904-14G1701960-14G1702100-14G1702240-14G1702310-14G1702380-14G1702450-14G1702590-14G1702660-14G1702800-14G1703150-14G1703360-14G1703500-14G1703850-14G1703920-14G1704326-14G1704578-14G1704956-14G170
1.621.661.831.851.992.112.162.252.342.412.632.702.952.983.093.163.193.283.523.753.873.994.104.344.454.695.275.635.866.456.567.247.678.30
Cat. No. Wt kg
14mm Pitch Gold High Power Belts Type 14G
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 14
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
15
600-5M25DD610-5M25DD615-5M25DD635-5M25DD640-5M25DD670-5M25DD675-5M25DD700-5M25DD705-5M25DD710-5M25DD725-5M25DD740-5M25DD750-5M25DD755-5M25DD800-5M25DD835-5M25DD850-5M25DD890-5M25DD900-5M25DD935-5M25DD940-5M25DD950-5M25DD980-5M25DD
1000-5M25DD1025-5M25DD1050-5M25DD1100-5M25DD1125-5M25DD1135-5M25DD1195-5M25DD1200-5M25DD1240-5M25DD1270-5M25DD1420-5M25DD1595-5M25DD1690-5M25DD1790-5M25DD1800-5M25DD1870-5M25DD1895-5M25DD1945-5M25DD2000-5M25DD2250-5M25DD2525-5M25DD
42434344454747494950515252535658606263656667697072747779798484878999
112118125126131133136140158177
600-5M15DD610-5M15DD615-5M15DD635-5M15DD640-5M15DD670-5M15DD675-5M15DD700-5M15DD705-5M15DD710-5M15DD725-5M15DD740-5M15DD750-5M15DD755-5M15DD800-5M15DD835-5M15DD850-5M15DD890-5M15DD900-5M15DD935-5M15DD940-5M15DD950-5M15DD980-5M15DD
1000-5M15DD1025-5M15DD1050-5M15DD1100-5M15DD1125-5M15DD1135-5M15DD1195-5M15DD1200-5M15DD1240-5M15DD1270-5M15DD1420-5M15DD1595-5M15DD1690-5M15DD1790-5M15DD1800-5M15DD1870-5M15DD1895-5M15DD1945-5M15DD2000-5M15DD2250-5M15DD2525-5M15DD
600610615635640670675700705710725740750755800835850890900935940950980
100010251050110011251135119512001240127014201595169017901800187018951945200022502525
Metric Series Timing Belt Drives
Double Sided Metric BeltsDouble-sided belts have teeth equally constructed on each side of the belt, which enables them to mesh with toothed pulleys onboth the inside and outside. The construction of the belts is basically the same as standard Metric belts, except that the nylon facing is also on the backing teeth, enabling full torque transmission from each side of the belt.
Double sided belts enable:-
• Reverse motion between internal and external pulleys. • Require only one belt to drive a series of pulleys.
• Simplified design layouts and weight reduction.
Standard Double sided belts are available in three sizes, 5M, 8M, and 14M, all operating on standard HTD pulleys.
5mm Pitch Double Sided Metric Belts Type 5M-DDBelt
Lengthmm
No.Teeth Cat. No.
600-5M9DD610-5M9DD615-5M9DD635-5M9DD640-5M9DD670-5M9DD675-5M9DD700-5M9DD705-5M9DD710-5M9DD725-5M9DD740-5M9DD750-5M9DD755-5M9DD800-5M9DD835-5M9DD850-5M9DD890-5M9DD900-5M9DD935-5M9DD940-5M9DD950-5M9DD980-5M9DD
1000-5M9DD1025-5M9DD1050-5M9DD1100-5M9DD1125-5M9DD1135-5M9DD1195-5M9DD1200-5M9DD1240-5M9DD1270-5M9DD1420-5M9DD1595-5M9DD1690-5M9DD1790-5M9DD1800-5M9DD1870-5M9DD1895-5M9DD1945-5M9DD2000-5M9DD2250-5M9DD2525-5M9DD
120122123127128134135140141142145148150151160167170178180187188190196200205210220225227239240248254284319338358360374379389400450505
25262627272828293030303131323435363738393940414243444647485050525360677175767980828495
106
9mm Wide Belt 15mm Wide Belt
Cat. No. WtgmsWtgms
7071727475787982828385878788949899
104106109110111115117120123129132133140140145149166187198209211219222228234263295
25mm Wide Belt
Cat. No. Wtgms
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 15
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
16
8mm Pitch Double Sided Metric Belts Type 8M-DD
Cat. No.
0.1700.1720.1790.1810.1920.2030.2260.2370.2490.2530.2600.2710.2830.2940.3050.3160.3390.3460.3620.3820.4070.4140.4520.4970.5090.5650.6220.6780.7120.7350.7910.8610.9271.0171.243
600-8M50DD608-8M50DD632-8M50DD640-8M50DD680-8M50DD720-8M50DD800-8M50DD840-8M50DD880-8M50DD896-8M50DD920-8M50DD960-8M50DD
1000-8M50DD1040-8M50DD1080-8M50DD1120-8M50DD1200-8M50DD1224-8M50DD1280-8M50DD1352-8M50DD1440-8M50DD1464-8M50DD1600-8M50DD1760-8M50DD1800-8M50DD2000-8M50DD2200-8M50DD2400-8M50DD2520-8M50DD2600-8M50DD2800-8M50DD3048-8M50DD3280-8M50DD3600-8M50DD4400-8M50DD
0.1020.1030.1070.1080.1150.1220.1360.1420.1490.1520.1560.1630.1700.1760.1830.1900.2030.2070.2170.2290.2440.2480.2710.2980.3050.3390.3730.4070.4270.4410.4750.5170.5560.6100.746
600608632640680720800840880896920960
10001040108011201200122412801352144014641600176018002000220024002520260028003048328036004400
BeltLength
mmNo.
Teeth Cat. No.
600-8M20DD608-8M20DD632-8M20DD640-8M20DD680-8M20DD720-8M20DD800-8M20DD840-8M20DD880-8M20DD896-8M20DD920-8M20DD960-8M20DD
1000-8M20DD1040-8M20DD1080-8M20DD1120-8M20DD1200-8M20DD1224-8M20DD1280-8M20DD1352-8M20DD1440-8M20DD1464-8M20DD1600-8M20DD1760-8M20DD1800-8M20DD2000-8M20DD2200-8M20DD2400-8M20DD2520-8M20DD2600-8M20DD2800-8M20DD3048-8M20DD3280-8M20DD3600-8M20DD4400-8M20DD
757679808590
100105110112115120125130135140150153160169180183200220225250275300315325350381410450550
0.0680.0690.0710.0720.0770.0810.0900.0950.0990.1010.1040.1080.1130.1180.1220.1270.1360.1380.1450.1530.1630.1650.1810.1990.2030.2260.2490.2710.2850.2940.3160.3440.3710.4070.497
20mm Wide Belt 30mm Wide Belt
Cat. No.Wt kg
50mm Wide Belt
600-8M30DD608-8M30DD632-8M30DD640-8M30DD680-8M30DD720-8M30DD800-8M30DD840-8M30DD880-8M30DD896-8M30DD920-8M30DD960-8M30DD
1000-8M30DD1040-8M30DD1080-8M30DD1120-8M30DD1200-8M30DD1224-8M30DD1280-8M30DD1352-8M30DD1440-8M30DD1464-8M30DD1600-8M30DD1760-8M30DD1800-8M30DD2000-8M30DD2200-8M30DD2400-8M30DD2520-8M30DD2600-8M30DD2800-8M30DD3048-8M30DD3280-8M30DD3600-8M30DD4400-8M30DD
Wt kg Wt kg
85mm Wide Belt
Cat. No. Wt kg
0.2880.2920.3040.3070.3270.3460.3840.4030.4230.4300.4420.4610.4800.4990.5190.5380.5760.5880.6150.6490.6920.7030.7680.8450.8640.9611.0571.1531.2101.2491.3451.4641.5751.7292.113
600-8M85DD608-8M85DD632-8M85DD640-8M85DD680-8M85DD720-8M85DD800-8M85DD840-8M85DD880-8M85DD896-8M85DD920-8M85DD960-8M85DD
1000-8M85DD1040-8M85DD1080-8M85DD1120-8M85DD1200-8M85DD1224-8M85DD1280-8M85DD1352-8M85DD1440-8M85DD1464-8M85DD1600-8M85DD1760-8M85DD1800-8M85DD2000-8M85DD2200-8M85DD2400-8M85DD2520-8M85DD2600-8M85DD2800-8M85DD3048-8M85DD3280-8M85DD3600-8M85DD4400-8M85DD
Wt kg
115mm Wide Belt85mm Wide Belt40mm Wide Belt
966994
1092110611901260128813441400144215681610175017641778184818901904196021002240231023802450259026602800296831503360350038503920432645784956
6971787985909296
100103112115125126127132135136140150160165170175185190200212225240250275280309327354
14mm Pitch Double-sided Metric Belts Type 14M- DD
Cat. No.
BeltLength
mmNo.
Teeth Cat. No.
55mm Wide Belt
Cat. No.Wt kg Wt kg Wt kg Cat. No.
966-14M40DD994-14M40DD
1092-14M40DD1106-14M40DD1190-14M40DD1260-14M40DD1288-14M40DD1344-14M40DD1400-14M40DD1442-14M40DD1568-14M40DD1610-14M40DD1750-14M40DD1764-14M40DD1778-14M40DD1848-14M40DD1890-14M40DD1904-14M40DD1960-14M40DD2100-14M40DD2240-14M40DD2310-14M40DD2380-14M40DD2450-14M40DD2590-14M40DD2660-14M40DD2800-14M40DD2968-14M40DD3150-14M40DD3360-14M40DD3500-14M40DD3850-14M40DD3920-14M40DD4326-14M40DD4578-14M40DD4956-14M40DD
0.380.390.430.440.470.500.510.530.550.570.620.630.690.700.700.730.740.750.770.830.880.910.940.971.021.051.101.171.241.321.381.521.541.701.801.95
966-14M55DD994-14M55DD
1092-14M55DD1106-14M55DD1190-14M55DD1260-14M55DD1288-14M55DD1344-14M55DD1400-14M55DD1442-14M55DD1568-14M55DD1610-14M55DD1750-14M55DD1764-14M55DD1778-14M55DD1848-14M55DD1890-14M55DD1904-14M55DD1960-14M55DD2100-14M55DD2240-14M55DD2310-14M55DD2380-14M55DD2450-14M55DD2590-14M55DD2660-14M55DD2800-14M55DD2968-14M55DD3150-14M55DD3360-14M55DD3500-14M55DD3850-14M55DD3920-14M55DD4326-14M55DD4578-14M55DD4956-14M55DD
0.520.540.590.600.640.680.700.730.760.780.850.870.950.960.961.001.021.031.061.141.211.251.291.331.401.441.521.611.711.821.902.092.122.342.482.68
966-14M85DD994-14M85DD
1092-14M85DD1106-14M85DD1190-14M85DD1260-14M85DD1288-14M85DD1344-14M85DD1400-14M85DD1442-14M85DD1568-14M85DD1610-14M85DD1750-14M85DD1764-14M85DD1778-14M85DD1848-14M85DD1890-14M85DD1904-14M85DD1960-14M85DD2100-14M85DD2240-14M85DD2310-14M85DD2380-14M85DD2450-14M85DD2590-14M85DD2660-14M85DD2800-14M85DD2968-14M85DD3150-14M85DD3360-14M85DD3500-14M85DD3850-14M85DD3920-14M85DD4326-14M85DD4578-14M85DD4956-14M85DD
0.810.830.910.931.001.051.081.131.171.211.311.351.471.481.491.551.581.591.641.761.881.931.992.052.172.232.342.482.642.812.933.223.283.623.834.15
966-14M115DD994-14M115DD
1092-14M115DD1106-14M115DD1190-14M115DD1260-14M115DD1288-14M115DD1344-14M115DD1400-14M115DD1442-14M115DD1568-14M115DD1610-14M115DD1750-14M115DD1764-14M115DD1778-14M115DD1848-14M115DD1890-14M115DD1904-14M115DD1960-14M115DD2100-14M115DD2240-14M115DD2310-14M115DD2380-14M115DD2450-14M115DD2590-14M115DD2660-14M115DD2800-14M115DD2968-14M115DD3150-14M115DD3360-14M115DD3500-14M115DD3850-14M115DD3920-14M115DD4326-14M115DD4578-14M115DD4956-14M115DD
1.091.131.241.251.351.431.461.521.591.631.781.821.982.002.012.092.142.162.222.382.542.622.702.782.933.013.173.363.573.813.964.364.444.905.195.61
966-14M170DD994-14M170DD
1092-14M170DD1106-14M170DD1190-14M170DD1260-14M170DD1288-14M170DD1344-14M170DD1400-14M170DD1442-14M170DD1568-14M170DD1610-14M170DD1750-14M170DD1764-14M170DD1778-14M170DD1848-14M170DD1890-14M170DD1904-14M170DD1960-14M170DD2100-14M170DD2240-14M170DD2310-14M170DD2380-14M170DD2450-14M170DD2590-14M170DD2660-14M170DD2800-14M170DD2968-14M170DD3150-14M170DD3360-14M170DD3500-14M170DD3850-14M170DD3920-14M170DD4326-14M170DD4578-14M170DD4956-14M170DD
1.621.661.831.851.992.112.162.252.342.412.632.702.932.952.983.093.163.193.283.523.753.873.994.104.344.454.694.975.275.635.866.456.567.247.678.30
Wt kg
170mm Wide Belt
Cat. No.
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 16
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
17
.006
.008
.010
.012
.010
.012
.014
.016
.018
.020
.027
.030
.038
.045
.060
.075
.095
.103
.150
.210
PulleyType
CatalogueNo.
No.Teeth
Z
Pitch CircleDiameter
dp
HTD Timing Pulleys - 3M Belts
Cross & Morse HTD Pulleys are manufactured to close tolerances to ensure concentric running, and have precision generatedgear teeth to match the high power and speed capabilities of HTD drive belts. Only high quality materials are used for pulley manufacture; aluminium being selected for 3M and larger 5M pulleys to keep weight and inertia low; all other pulleys machinedfrom medium carbon steel bar or 260 Grade cast iron and finished with zinc phosphate for corrosion protection.Standard pulleys are offered with a large range of tooth sizes in widths to suit all standard HTD belts. Pulleys for 5M, 8M and14M drives are available with parallel pilot bore for reworking to customers requirements , bored for shaft clamping elements, orwith taper bore to be combined with stock taper brushes for the complete off- the Shelf drive. Pulleys of non-standard widths or numbers of teeth can be supplied to order, or teeth can be generated on customers own blanks.Smaller pulleys are fitted with two flanges to retain the drive belt, these being identified in tables by suffix ‘F’ on pulley type. Theflanges are pressed onto pulley body and retained by spin rivetting.
EF
Belt Size
Belt Width mm
3M
9 15 9 15 25
5M 8M 14M
20 30 50 85 40 55 85 115 170
10.213.4
1720
11.914.5
17.920.5
27.930.5
2328
3338
5560
9095
4754
6370
95102
126133
180187
Min.Bore
d
MaxBore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
Approx.Weight
kg
3mm Pitch Pulleys for 9mm wide Belts. Ref. 3M0910-3M-0912-3M-0914-3M-0915-3M-0916-3M-0918-3M-0920-3M-0921-3M-0922-3M-0924-3M-0926-3M-0928-3M-0930-3M-0932-3M-0936-3M-0940-3M-0944-3M-0948-3M-0960-3M-0972-3M-09
1012141516182021222426283032364044486072
0F0F0F0F1F1F1F1F1F1F1F1F1F1F1F1F1F111
9.5511.4613.3714.3215.2817.1919.1020.0521.0122.9224.8326.7428.6530.5534.3838.2042.0245.8457.3068.75
4.04.04.04.04.06.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
4.06.07.08.06.57.08.08.58.58.5
10.511.512.714.017.018.522.522.522.522.5
13.015.016.017.518.020.023.025.025.025.028.032.032.036.038.042.048.0
–––
10.210.210.210.212.812.812.812.812.812.812.812.812.812.813.413.413.413.413.413.4
3mm Pitch Pulleys for 15mm wide Belts. Ref. 3M15
8.810.712.613.614.516.418.319.320.322.224.126.027.929.833.637.441.345.156.568.0
17.517.517.517.520.620.620.620.620.620.620.620.620.620.622.222.222.222.222.222.2
13.015.016.017.510.011.013.013.013.013.016.018.020.022.026.028.033.033.033.033.0
.004
.006
.007
.008
.007
.008
.010
.013
.014
.016
.018
.024
.028
.032
.045
.055
.074
.074
.106
.145
3mm Pitch Pulleys for 6mm wide Belts. Ref. 3M0610-3M-0612-3M-0614-3M-0615-3M-0616-3M-0618-3M-0620-3M-0621-3M-0622-3M-0624-3M-0626-3M-0628-3M-0630-3M-0632-3M-0636-3M-0640-3M-0644-3M-0648-3M-0660-3M-0672-3M-06
1012141516182021222426283032364044486072
0F0F0F0F1F1F1F1F1F1F1F1F1F1F1F1F1F111
9.5511.4613.3714.3215.2817.1919.1020.0521.0122.9224.8326.7428.6530.5534.3838.2042.0245.8457.3068.75
4.04.04.04.04.06.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
4.06.07.08.06.57.08.08.58.58.5
10.511.512.714.017.018.522.522.522.522.5
13.015.016.017.518.020.023.025.025.025.028.032.032.036.038.042.048.0
–––
7.27.27.27.29.89.89.89.89.89.89.89.89.89.8
10.310.310.310.310.310.3
8.810.712.613.614.516.418.319.320.322.224.126.027.929.833.637.441.345.156.568.0
14.514.514.514.517.517.517.517.517.517.517.517.517.517.518.018.018.018.618.618.6
13.015.016.017.510.011.013.013.013.013.016.018.020.022.026.028.033.033.033.033.0
.003
.005
.006
.007
.006
.007
.008
.011
.012
.014
.016
.021
.024
.028
.039
.047
.062
.062
.091
.124
10-3M-1512-3M-1514-3M-1515-3M-1516-3M-1518-3M-1520-3M-1521-3M-1522-3M-1524-3M-1526-3M-1528-3M-1530-3M-1532-3M-1536-3M-1540-3M-1544-3M-1548-3M-1560-3M-1572-3M-15
1012141516182021222426283032364044486072
0F0F0F0F1F1F1F1F1F1F1F1F1F1F1F1F1F111
9.5511.4613.3714.3215.2817.1919.1020.0521.0122.9224.8326.7428.6530.5534.3838.2042.0245.8457.3068.75
4.04.04.04.04.06.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
4.06.07.08.06.57.08.08.58.58.5
10.511.512.714.017.018.522.522.522.522.5
8.810.712.613.614.516.418.319.320.322.224.126.027.929.833.637.441.345.156.568.0
13.015.016.017.518.020.023.025.025.025.028.032.032.036.038.042.048.0
–––
13.015.016.017.510.011.013.013.013.013.016.018.020.022.026.028.033.033.033.033.0
17.017.017.017.019.519.519.519.519.519.519.519.519.519.520.020.020.020.020.020.0
26.026.026.026.026.026.026.026.026.026.026.026.026.026.030.030.030.030.030.030.0
Type 1Material: Aluminium
Type 0FMaterial: Aluminium
dp do
F
d MA
L
d Mdp do
F
L
F
E
L
F
d MA dp do
Type 1FMaterial: Aluminium
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 17
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
18
HTD Timing Pulleys - 5M BeltsPulley TypesPulley types referred to in tables areas drawings below. The suffix ‘F’indicates pulley flanges
Pulley InstallationCorrect and accurate installation of Timing Drives is essential. Pulley alignment and shaft parallelism is very important as misalignment ofthe drive will cause unequal loading across the belt width and edge wear of belt on flanges. Pulley alignment can be checked by placing astraight edge against the outside edge of the pulleys and adjusting so contact made evenly across both pulleys.The shaft should be located within a rigid framework, as any distortion under load could result in a reduction of centre distance which willcause jumping of belt on pulley teeth. If idlers are used they must be locked firmly into position after correct belt tensioning. Refer to page 10 for additional on drive installation.
12-5M-2514-5M-2515-5M-2516-5M-2518-5M-2520-5M-2521-5M-2522-5M-2524-5M-2526-5M-2528-5M-2530-5M-2532-5M-2536-5M-2540-5M-25
44-5M-2548-5M-2560-5M-2572-5M-25
121415161820212224262830323640
44486072
19.1022.2823.8725.4628.6531.8333.4235.0138.2041.3844.5647.7550.9357.3063.66
70.0376.3995.49
114.59
4.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
8.08.08.08.0
1F1F1F1F1F1F1F1F1F1F1F1F1F1F1F
2222
78
10111314151618202024262626
26303030
18.021.122.724.327.530.732.333.937.140.243.446.649.856.262.5
68.975.394.4
113.5
20.520.520.520.520.520.520.520.520.520.520.520.520.520.520.5
20.520.520.520.5
26.026.026.026.026.026.026.026.028.028.028.028.028.028.028.0
30.030.030.030.0
12.013.016.016.520.023.024.025.527.030.030.535.038.038.038.0
38.045.045.045.0
_______________
546180
100
.034
.046
.056
.064
.086
.112
.130
.140
.180
.220
.250
.300
.350
.426
.520
.225
.187
.305
.375
23.025.028.028.032.036.038.038.042.044.048.051.054.060.070.0
____
12-5M-1514-5M-1515-5M-1516-5M-1518-5M-1520-5M-1521-5M-1522-5M-1524-5M-1526-5M-1528-5M-1530-5M-1532-5M-1536-5M-1540-5M-15
44-5M-1548-5M-1560-5M-1572-5M-15
CatalogueNo.
12-5M-0914-5M-0915-5M-0916-5M-0918-5M-0920-5M-0921-5M-0922-5M-0924-5M-0926-5M-0928-5M-0930-5M-0932-5M-0936-5M-0940-5M-09
44-5M-0948-5M-0960-5M-0972-5M-09
All dimensions in mm. Other sizes of Pulleys can be supplied on short delivery. Pulleys can be supplied bored and keywayed.For Taper Bore Pulleys see page 21.
No.Teeth
ZPulleyType
Pitch CircleDiameter
dp
Min.Bore
d
MaxBore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
Approx.Weight
kg
RimDiameter
N
5mm Pitch Pulleys for 9mm wide Belts. Ref. 5M09
5mm Pitch Pulleys for 15mm wide Belts. Ref. 5M15
121415161820212224262830323640
44486072
19.1022.2823.8725.4628.6531.8333.4235.0138.2041.3844.5647.7550.9357.3063.66
70.0376.3995.49
114.59
4.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
8.08.08.08.0
23.025.028.028.032.036.038.038.042.044.048.051.054.060.070.0
____
1F1F1F1F1F1F1F1F1F1F1F1F1F1F1F
2222
78
10111314151618202024262626
26263030
18.021.122.724.327.530.732.333.937.140.243.446.649.856.262.5
68.975.394.4
113.5
14.514.514.514.514.514.514.514.514.514.514.514.514.514.514.5
14.514.514.514.5
20.020.020.020.020.022.522.522.522.522.522.522.522.522.522.5
25.525.525.525.5
12.013.016.016.520.023.024.025.527.030.030.535.038.038.038.0
38.045.045.045.0
_______________
546180
100
.028
.034
.042
.050
.070
.094
.110
.118
.145
.170
.200
.236
.270
.324
.400
.170
.182
.230
.270
5mm Pitch Pulleys for 25mm wide Belts. Ref. 5M25
121415161820212224262830323640
44486072
19.1022.2823.8725.4628.6531.8333.4235.0138.2041.3844.5647.7550.9357.3063.66
70.0376.3995.49
114.59
4.06.06.06.06.06.06.06.06.06.06.06.08.08.08.0
8.08.08.08.0
1F1F1F1F1F1F1F1F1F1F1F1F1F1F1F
2222
78
10111314151618202024262626
26303030
18.021.122.724.327.530.732.333.937.140.243.446.649.856.262.5
68.975.394.4
113.5
30.530.530.530.530.530.530.530.530.530.530.530.530.530.530.5
30.530.530.530.5
36.036.036.036.036.036.038.038.038.038.038.038.038.038.038.0
40.040.040.040.0
12.013.016.016.520.023.024.025.527.030.030.535.038.038.038.0
38.045.045.045.0
–––––––––––––––
546180
100
0.500.700.80.100.120.160.180.210.250.300.350.420.485.595.745
.320
.275
.435
.525
23.025.028.028.032.036.038.038.042.044.048.051.054.060.070.0
____
L
F
d MA dp do
FL
dodp N d M
Type 2Material: Aluminium
Type 1FMaterial: Steel
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:50 Page 18
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
19
*Non-stock items, manufactured to customer order only. All dimensions in mm.Standard Pulleys can be reworked to customers bore and keyway requirements
105105105105105105105105105105105105105
9595
959595959595
P22-8M-50P24-8M-50P26-8M-50P28-8M-50P30-8M-50P32-8M-50P34-8M-50P36-8M-50P38-8M-50P40-8M-50P44-8M-50P48-8M-50P56-8M-50P64-8M-50P72-8M-50
P80-8M-50P90-8M-50
P112-8M-50P144-8M-50P168-8M-50P192-8M-50
P22-8M-85P24-8M-85P26-8M-85P28-8M-85P30-8M-85P32-8M-85P34-8M-85P36-8M-85P38-8M-85P40-8M-85P44-8M-85P48-8M-85P56-8M-85P64-8M-85P72-8M-85
P80-8M-85P90-8M-85
P112-8M-85P144-8M-85P168-8M-85P192-8M-85
Approx.Weight
kg
P22-8M-20P24-8M-20P26-8M-20P28-8M-20P30-8M-20P32-8M-20P34-8M-20P36-8M-20P38-8M-20P40-8M-20P44-8M-20P48-8M-20P56-8M-20P64-8M-20P72-8M-20
P80-8M-20P90-8M-20
P112-8M-20P144-8M-20P168-8M-20P192-8M-20
CatalogueNo.
Plain Bore Pulleys 8M Belts
Pulley TypesThe Pulley types referred to in tables are as drawings below. Suffix ‘F’ indicates pulley has flanges. Pulley below dividing line in tables are manufactured in cast iron. Pulleys 112 teeth(80 teeth on 8M-85) and aboveincorporate lightening holes indesign.
No.Teeth
Z
PulleyType
PitchCircle
Diameterdp
Min.Bore
d
MaxBore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
RimDiameter
N
222426283032343638404448566472
8090
112144168192
1F1F1F1F1F1F1F1F1F1F1F1F2F2F2F
222222
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
203.72229.18285.21366.69427.81488.92
121212151515151515151515151515
151518202020
293032343640465050505050545454
545454546060
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
202.4227.8283.8365.3426.4487.6
6066707583879197
102106120128150168192
––––––
383838383838383838383838383838
383838383838
282828282828282828282828282828
282828282828
434548505560707575757575808080
90909090
100100
____________
116137158
180204254336400460
0.540.650.800.871.021.201.401.551.651.742.102.442.602.903.10
3.804.205.207.50
10.0014.40
222426283032343638404448566472
8090
112144168192
1F1F1F1F1F1F1F1F1F1F1F1F2F2F2F
222222
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
203.72229.18285.21366.69427.81488.92
121212151515151515151515151515
151518202020
293032343640465050505050606063
606060606060
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
202.4227.8283.8365.3426.4487.6
6066707583879197
102106120128150168192
––––––
383838383838383838383838383838
383838383838
434548505560707575757575909095
100100100100100100
____________
116137158
180204254336400460
0.690.841.001.121.321.531.801.992.272.402.803.203.604.304.80
5.105.706.809.30
11.4016.00
P22-8M-30P24-8M-30P26-8M-30P28-8M-30P30-8M-30P32-8M-30P34-8M-30P36-8M-30P38-8M-30P40-8M-30P44-8M-30P48-8M-30P56-8M-30P64-8M-30P72-8M-30
P80-8M-30P90-8M-30
P112-8M-30P144-8M-30P168-8M-30P192-8M-30
484848484848484848484848484848
484848484848
222426283032343638404448566472
8090
112144168192
1F1F1F1F1F1F1F1F1F1F1F1F3F3F3F
333333
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
203.72229.18285.21366.69427.81488.92
293032343640444650505054606767
666666667278
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
202.4227.8283.8365.3426.4487.6
6066707583879197
102106120128150168192
––––––
606060606060606060606060606060
606060606060
707070707070707070707070606060
606060606060
121215151515151515181818181818
181818202020
43454850556066707575758090
100100
110110110110120130
____________
116137158
180204254336400460
1.001.231.501.671.972.272.692.973.233.503.904.305.005.606.80
6.908.609.60
13.8016.0022.40
222426283032343638404448566472
8090
112144168192
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
203.72229.18285.21366.69427.81488.92
293032343640444650505054546767
666666667278
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
202.4227.8283.8365.3426.4487.6
6066707583879197
102106120128150168192
––––––
959595959595959595959595959595
959595959595
121212151515151515181818182020
202024242424
43454850556066707575758090
100100
110110110110120130
_____________
137158
180204254336400460
1.551.902.252.553.003.574.004.505.005.206.607.00
10.0010.4011.40
11.1012.2015.0021.5024.1030.60
1F1F1F1F1F1F1F1F1F1F1F1F1F3F3F
333333
8mm Pitch Pulleys for 85mm wide Belts. Ref. 8M85
8mm Pitch Pulleys for 50mm wide Belts. Ref. 8M50
8mm Pitch Pulleys for 30mm wide Belts. Ref. 8M30
8mm Pitch Pulleys for 20mm wide Belts. Ref. 8M20
Type 3/3FMaterial: Steel or Cast Iron
Type 1FMaterial: Steel
L
F
d MA dodp
F/L
d MA dodp NType 2/2F
Material: Steel or Cast Iron
L
F
d MA dodp N
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:51 Page 19
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
20
283032343638404864
8090
112144192
4.735.456.176.887.608.289.26
10.32
11.5013.0514.4016.9018.5020.0026.7035.0044.2052.20
CatalogueNo.
No.Teeth
ZPulleyType
PitchCircle
Dia. dp
Max.Bore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
RimDiameter
N
ApproxWeight
kg
P28-14M-40P30-14M-40P32-14M-40P34-14M-40P36-14M-40P38-14M-40P40-14M-40P44-14M-40
P48-14M-40P56-14M-40P64-14M-40P72-14M-40P80-14M-40P90-14M-40
P112-14M-40P144-14M-40P168-14M-40P192-14M-40
Min.Bore
d
14mm Pitch Pulleys for 40mm Wide Belts. Ref. 14M40
14mm Pitch Pulleys for 55mm Wide Belts. Ref. 14M55
2830323436384044
485664728090
112144168192
1F1F1F1F1F1F1F1F
2F2F2F2222222
124.78133.69142.60151.52160.43169.34178.25196.08
213.90249.55285.21320.86356.51401.07499.11641.71748.66855.62
2424242424242424
24282828282828282828
6767676767808080
82828282828282828282
122.1131.0139.9148.8157.7166.6175.5193.3
211.1246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212
226256296_______
5454545454545454
54545454545454545454
6969696969696969
69696969696969696969
100100100100100120120120
135135135135135135135135135135
________
170207240278314358456600706813
P28-14M-55P30-14M-55P32-14M-55P34-14M-55P36-14M-55P38-14M-55P40-14M-55P44-14M-55
P48-14M-55P56-14M-55P64-14M-55P72-14M-55P80-14M-55P90-14M-55
P112-14M-55P144-14M-55P168-14M-55P192-14M-55
2830323436384044
485664728090
112144188192
1F1F1F1F1F1F1F1F
3F3F3F3333333
124.78133.69142.60151.52160.43169.34178.25196.08
213.90249.55285.21320.86356.51401.07499.11641.71748.66855.62
2424242424242424
24282828282828282828
6767676767808080
82828282828282828282
122.1131.0139.9148.8157.7166.6175.5193.3
211.1246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212226
256296_______
7070707070707070
70707070707070707070
8585858585858585
70707070707070707070
100100100100100120120120
135135135135135135135135135135
________
170207240278314358456600706813
5.606.607.608.609.60
10.8011.2012.50
13.7014.5015.6016.9020.0022.6029.5039.0048.5057.80
14mm Pitch Pulleys for 85mm Wide Belts. Ref. 14M85
P28-14M-85P30-14M-85P32-14M-85P34-14M-85P36-14M-85P38-14M-85P40-14M-85P44-14M-85P48-14M-85
P56-14M-85P64-14M-85P72-14M-85P80-14M-85P90-14M-85
P112-14M-85P144-14M-85P168-14M-85P192-14M-85
283032343638404448
5664728090
112144168192
1F1F1F1F1F1F1F1F1F
3F3F3333333
124.78133.69142.60151.52160.43169.34178.25196.08213.90
249.55285.21320.86356.51401.07499.11641.71748.66855.62
6767676767809090
100
9090909090909090
100
242424242432323232
323232323232323232
_________
207240278314358456600706813
7.709.10
10.5011.9013.2015.1517.1023.3025.00
25.0030.5028.8030.1033.0041.8052.4060.3070.20
122.1131.0139.9148.8157.7166.6175.5193.3211.1
246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212
226256296_______
102102102102102102102102102
102102102102102102102102102
117117117117117117117117117
102102102102102102102102102
100100100100100120135135150
150150150150150150150150165
14mm Pitch Pulleys for 115mm Wide Belts. Ref. 14M115
128138154160168184188212226256
296_______
P28-14M-115P30-14M-115P32-14M-115P34-14M-115P36-14M-115P38-14M-115P40-14M-115P44-14M-115P48-14M-115P56-14M-115
P64-14M-115P72-14M-115P80-14M-115P90-14M-115
P112-14M-115P144-14M-115P168-14M-115P192-14M-115
28303234363840444856
64728090
112144168192
1F1F1F1F1F1F1F1F1F1F
3F3333333
124.78133.69142.60151.52160.43169.34178.25196.08213.90249.55
285.21320.86356.51401.07499.11641.71748.66855.62
6767676767809094
100100
9090909090
100100100
32323232323232323232
3232323232323232
122.1131.0139.9148.8157.7166.6175.5193.3211.1246.8
282.4318.1353.7398.3496.3638.9745.9852.8
133133133133133133133133133133
133133133133133133133133
148148148148148148148148148148
133133133133133133133133
100100100100100120135140150150
150150150150150165165165
__________
240278314358456600706813
9.2011.2013.2014.8016.6018.2020.5621.9325.0027.50
30.1032.8335.5541.0054.4067.8075.8088.30
14mm Pitch Pulleys for 170mm Wide Belts. Ref. 14M170
128138154160168183188226296
–––––
1F1F1F1F1F1F1F1F3F
33333
124.78133.69142.60151.52160.43169.34178.25213.90285.21
356.51401.07499.11641.71855.62
676767678090909090
108108108108108
323232323232323232
3232323232
122.1131.0139.9148.8157.7166.6175.5211.1282.4
353.7398.3496.3638.9852.8
187187187187187187187187187
187187187187187
202202202202202202202202202
187187187187187
100100100100120135140150150
180180200220220
––––––––
240
314358456600813
14.8016.7019.4021.8525.2028.4032.2639.5054.00
69.4071.3088.00
113.00140.00
P28-14M-170P30-14M-170P32-14M-170P34-14M-170P36-14M-170P38-14M-170P40-14M-170P48-14M-170P64-14M-170
P80-14M-170P90-14M-170
P112-14M-170P144-14M-170P192-14M-170
Plain Bore Pulleys 14M Belts
Pulley TypesThe pulley types referred to intables are as drawings below.Suffix ‘F’ indicates pulley hasflanges. Pulleys below dividing line in tables are manufactured in cast iron, unflanged pulleysincorporate lightening holes indesign, except P80-14M-170.Std. Pulleys can be reworked tocustomers bore and keywayrequirements.
All dimensions in mm.Standard Pulleys can be reworked to customers bore and keyway requirements.
Type 1FMaterial: Steel
L
F
d MA dodp
Type 2/2FMaterial: Steel or Cast Iron
L
F
d MA dodp N
F/L
Type 3/3FMaterial: Cast Iron
d MA dodp N
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:51 Page 20
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
21
Taper Bore Pulleys forHTD Size 5M & 8M Belts
Pulley TypesThe pulley types referred to intables are as drawingsfollowing. Suffix ‘F’ indicatespulley has flanges. Pulleysbelow dividing lines in tablesare manufactured in Cast Iron,and pulleys over 300mmdiameter generally havelightening holes in web.
CatalogueNo.
5mm Pitch Pulleys for 15mm Wide Belt Ref. 5M15
8mm Pitch Pulleys for 20mm Wide Belt Ref. 8M20
8mm Pitch Pulleys for 30mm Wide Belt Ref. 8M30
8mm Pitch Pulleys for 50mm Wide Belt Ref. 8M50
8mm Pitch Pulleys for 85mm Wide Belt Ref. 8M85
No.Teeth
ZPulleyType
PitchCircle
Dia. dp
TaperBushRef.
Max.Bore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
RimDiameter
N
ApproxWeight
kg
34-5M-1536-5M-1538-5M-1540-5M-1544-5M-1548-5M-1556-5M-1564-5M-1572-5M-1580-5M-1590-5M-15
112-5M-15136-5M-15
3436384044485664728090
112136
9F9F9F 9F9F8F 8F 8F88887
54.1157.3060.4863.6670.0376.3989.13
101.86114.59127.32143.24178.25216.45
53.056.259.462.568.975.387.9
100.7113.5126.2142.1177.1215.3
1008110811081108110812101210121016101610161020122012
25282828283232324242425050
22222222222222222222222020
22222222222525252525253232
–––––597080929292
110110
––––––––––––
199
0.230.230.290.380.480.500.660.851.251.702.253.203.60
57606670758393
106–––––
22-8M-2024-8M-2026-8M-2028-8M-2030-8M-2032-8M-2034-8M-2036-8M-2038-8M-2040-8M-2044-8M-2048-8M-2056-8M-2064-8M-2072-8M-20
222426283032343638404448566472
5F5F5F5F5F 5F5F5F 5F 5F8F8F8F
11F11F
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
110811081108110811081610161016101610161020122012201220122012
282828282842424242425050505050
282828282828282828282828282828
222222222225252525253232323232
––––––––––9396
110110110
37444550586364687276–––
137158
0.260.300.360.440.530.420.550.680.801.001.201.602.402.703.30
6066707583879197
102106120128150168192
80-8M-2090-8M-20
8090
1111
203.72229.18
202.4227.8
20122012
5050
2828
3232
110110
180204
3.503.65
––
28-8M-5030-8M-5032-8M-5034-8M-5036-8M-5038-8M-5040-8M-5044-8M-5048-8M-5056-8M-5064-8M-5072-8M-50
283032343638404448566472
13F5F 5F5F5F 5F
13F13F13F13F13F12F
71.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
70.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
121016151615161516151615201220122012251725172517
324242424242505050606060
606060606060606060606060
253838383838323232454545
–––––––––––
125
505862656872829195
116137158
0.600.650.821.061.301.601.711.782.303.405.006.70
7583879197
102106120128150168192
80-8M-5090-8M-50
112-8M-50144-8M-50168-8M-50192-8M-50
8090
112144168192
13121212
77
203.72229.18285.21366.69427.81488.92
202.4227.8283.8365.3426.4487.6
302030203020302035253525
757575759090
606060606060
515151516565
–170170170198198
180204260341402460
8.8010.0012.0015.2017.5024.00
–––– ––
34-8M-8536-8M-8538-8M-8540-8M-8544-8M-8548-8M-8556-8M-8564-8M-8572-8M-85
343638404448566472
13F13F13F13F13F13F13F13F13F
86.5891.6796.77
101.86112.05122.23142.60162.97183.35
85.290.395.4
100.5110.7120.9141.2161.6182.0
161516151615201220122517251725173020
424242505060606075
959595959595959595
383838323245454551
–––––––––
6568728291
100117137158
1.431.872.201.802.302.664.456.208.00
9197
102106120128150168192
80-8M-8590-8M-85
112-8M-85144-8M-85168-8M-85192-8M-85
8090
112144168192
131212121212
203.72229.18285.21366.69427.81488.92
202.4227.8283.8365.3426.4487.6
302030203020352535253525
757575909090
959595959595
515151656565
–170170198198198
180204260336395455
10.0010.8015.0020.0022.0026.00
–––– ––
For bore sizes of Taper Bushes for above pulleys refer to page 25. Pulleys are also available with pilotbore ref. pages 17-20. All dimensions in mm.
22-8M-3024-8M-3026-8M-3028-8M-3030-8M-3032-8M-3034-8M-3036-8M-3038-8M-3040-8M-3044-8M-3048-8M-3056-8M-3064-8M-3072-8M-30
222426283032343638404448566472
5F5F5F5F9F 9F9F9F 9F 9F
13F13F13F8F
11F
56.0261.1266.2171.3076.3981.4986.5891.6796.77
101.86112.05122.23142.60162.97183.35
54.759.864.970.175.180.285.290.395.4
100.5110.7120.9141.2161.6182.0
110811081108121016151615161516151615161520122012201225172517
282828324242424242425050506060
383838383838383838383838383838
222222253838383838383232324545
–––––––––––––
125125
37444450––––––8690
110–
158
0.320.380.450.500.550.590.770.961.151.341.331.783.764.204.30
6066707583879197
102106120128150168192
80-8M-3090-8M-30
112-8M-30144-8M-30
8090
112144
11111111
203.72229.18285.21366.69
202.4227.8283.8365.3
2517251725172517
60606060
38383838
45454545
125125125125
180204254336
4.605.006.209.00
––––
Timing Belt Catalogue_Cross + Morse 14/12/2010 14:09 Page 21
INDEX BACK NEXT
Te
l +
44
1
21
3
60
0
15
5 F
ax
+
44
1
21
3
25
1
07
9 E
ma
il s
ale
s@
cr
os
sm
or
se
.c
om
22
Type 11/11F
dp do
L
F
A M N
dp do
F/L
M N
dp do
L
F
A M N
do
F
L
A AN
All dimensions in mm.For 14M170 belt drives a standard range of pilot bore pulleys is available, ref page 20, alternativelytaper bore sprockets can be manufactured to order, for details of recommended dimensions contactCross & Morse Technical Department. For bore sizes of Taper Bushes refer to page 25.* Non-stock items manufactured to customer order only.
9498
108110120130138155170
208240280315360457600706813
ApproxWeight
kg
RimDiameter
N
Taper Bore Pulleys forHTD Size 14M BeltsPulley TypesThe pulley types referred to intables are as drawings following. Suffix ‘F’ indicates pulley has flanges. Pulleys below dividing lines in tables are manufactured in Cast iron, and pulleys over 350mmdiameter generally havelightening holes in web.
28-14M-8530-14M-8532-14M-8534-14M-8536-14M-8538-14M-8540-14M-8544-14M-8548-14M-85
56-14M-8564-14M-8572-14M-8580-14M-8590-14M-85
112-14M-85144-14M-85168-14M-85192-14M-85
28-14M-4030-14M-4032-14M-4034-14M-4036-14M-4038-14M-4040-14M-4044-14M-4048-14M-40
56-14M-4064-14M-4072-14M-4080-14M-4090-14M-40
112-14M-40144-14M-40168-14M-40192-14M-40
CatalogueNo.
No.Teeth
Z
PulleyType
PitchCircle
Dia. dp
Max.Bore
d
OutsideDiameter
do
FlangeDiameter
A
PulleyWidth
F
BoreLength
L
HubDiameter
M
TaperBushRef.
14mm Pitch Pulleys for 40mm Wide Belts. Ref. 14M40
14mm Pitch Pulleys for 55mm Wide Belts. Ref. 14M55
283032343638404448
5664728090
112144168192
13F13F13F13F13F13F13F13F13F
12F12F12121212121212
124.78133.69142.60151.52160.43169.34178.25196.08213.90
249.55285.21320.86356.51401.07499.11641.71748.66855.62
201220122012251725172517251730203020
302030203020302030203020302030203020
505050606060607575
757575757575757575
122.1131.0139.9148.8157.7166.6175.5193.3211.1
246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212226
256296–––––––
545454545454545454
545454545454545454
2.072.653.403.874.805.406.007.809.40
10.8013.4015.2016.0017.8025.6032.0044.0049.00
323232454545455151
515151515151515151
–––––––––
170170170170170170170170170
28-14M-5530-14M-5532-14M-5534-14M-5536-14M-5538-14M-5540-14M-5544-14M-5548-14M-55
56-14M-5564-14M-5572-14M-5580-14M-5590-14M-55
112-14M-55144-14M-55168-14M-55192-14M-55
283032343638404448
5664728090
112144168192
13F13F13F13F13F13F13F13F13F
12F12F12121212121212
124.78133.69142.60151.52160.43169.34178.25196.08213.90
249.55285.21320.86356.51401.07499.11641.71748.66855.62
201225172517251725172517251730203020
302030203020302030203020302030203020
506060606060607575
757575757575757575
122.1131.0139.9148.8157.7166.6175.5193.3211.1
246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212226
256296–––––––
707070707070707070
707070707070707070
324545454545455151
515151515151515151
–––––––––
170170170170170170170170170
94100108110120130138155170
208240280315360457600706813
2.202.703.604.555.206.207.008.60
10.40
12.4014.5016.2017.5020.1028.4036.2049.0053.00
14mm Pitch Pulleys for 85mm Wide Belts. Ref. 14M85
283032343638404448
5664728090
112144168192
13F13F13F13F13F13F13F13F13F
13F12F12121212121210
124.78133.69142.60151.52160.43169.34178.25196.08213.90
249.55285.21320.86356.51401.07499.11641.71748.66855.62
251725172517251730203020302030203020
352535253525352535253525352535254040
606060607575757575
9090909090909090
100
122.1131.0139.9148.8157.7166.6175.5193.3211.1
246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212226
256296–––––––
102102102102102102102102102
102102102102102102102102102
454545455151515151
6565656565656565
102
–––––––––
–190190190190190190190230
98100108110120130138153170
210240280315360457600706813
2.703.754.806.006.336.808.00
11.8015.10
19.0023.0025.0026.0027.8036.5048.0060.0086.00
14mm Pitch Pulleys for 115mm Wide Belts. Ref. 14M115
28-14M-11530-14M-11532-14M-11534-14M-11536-14M-11538-14M-11540-14M-11544-14M-11548-14M-115
56-14M-115*64-14M-115*72-14M-115
80-14M-11590-14M-115
112-14M-115144-14M-115168-14M-115192-14M-115
283032343638404448
5664728090
112144168192
13F13F13F13F13F13F13F13F13F
13F12F12121212121212
124.78133.69142.60151.52160.43169.34178.25196.08213.90
249.55285.21320.86356.51401.07499.11641.71748.66855.62
251725172517251730203020302030303030
353535353535353535353535404040404040
606060607575757575
909090909090
100100100
122.1131.0139.9148.8157.7166.6175.5193.3211.1
246.8282.4318.1353.7398.3496.3638.9745.9852.8
128138154160168184188212226
256296–––––––
133133133133133133133133133
133133133133133133133133133
454545455151517676
898989898989
102102102
–––––––––
–190190190190190230230230
98100108110125130138155170
208240280315360457600706813
3.775.006.808.008.408.709.20
14.0017.10
24.8027.0029.0032.0036.5046.0068.0082.6096.00
Type 13/13F
Type 12/12F
Type 10
Timing Belt Catalogue_Cross + Morse 13/12/2010 17:51 Page 22
