30
Metal Matrix Composites Andreas Mortensen 1 and Javier Llorca 2 1 Institute of Materials, Ecole Polytechnique F´ ed´ erale de Lausanne (EPFL), CH-1015, Lausanne, Switzerland; email: andreas.mortensen@epfl.ch 2 Madrid Institute for Advanced Studies of Materials (IMDEA-Materials) and Department of Materials Science, Polytechnic University of Madrid, E-28040, Madrid, Spain; email: [email protected] Annu. Rev. Mater. Res. 2010. 40:243–70 First published online as a Review in Advance on March 26, 2010 The Annual Review of Materials Research is online at matsci.annualreviews.org This article’s doi: 10.1146/annurev-matsci-070909-104511 Copyright c 2010 by Annual Reviews. All rights reserved 1531-7331/10/0804-0243$20.00 Key Words fiber-reinforced composites, particle-reinforced composites, layered materials, strength, ductility, stiffness Abstract In metal matrix composites, a metal is combined with another, often non- metallic, phase to produce a novel material having attractive engineering attributes of its own. A subject of much research in the 1980s and 1990s, this class of materials has, in the past decade, increased significantly in variety. Copper matrix composites, layered composites, high-conductivity compos- ites, nanoscale composites, microcellular metals, and bio-derived composites have been added to a palette that, ten years ago, mostly comprised ceramic fiber– or particle-reinforced light metals together with some well-established engineering materials, such as WC-Co cermets. At the same time, research on composites such as particle-reinforced aluminum, aided by novel tech- niques such as large-cell 3-D finite element simulation or computed X-ray microtomography, has served as a potent vehicle for the elucidation of the mechanics of high-contrast two-phase elastoplastic materials, with implica- tions that range well beyond metal matrix composites. 243 Annu. Rev. Mater. Res. 2010.40:243-270. Downloaded from www.annualreviews.org by Cinvestav del IPN on 01/27/12. For personal use only.

Metal Matrix Composites

Embed Size (px)

Citation preview

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    Metal Matrix CompositesAndreas Mortensen1 and Javier Llorca21Institute of Materials, Ecole Polytechnique Federale de Lausanne (EPFL), CH-1015,Lausanne, Switzerland; email: [email protected] Institute for Advanced Studies of Materials (IMDEA-Materials) and Department ofMaterials Science, Polytechnic University of Madrid, E-28040, Madrid, Spain;email: [email protected]

    Annu. Rev. Mater. Res. 2010. 40:24370

    First published online as a Review in Advance onMarch 26, 2010

    The Annual Review of Materials Research is online atmatsci.annualreviews.org

    This articles doi:10.1146/annurev-matsci-070909-104511

    Copyright c 2010 by Annual Reviews.All rights reserved

    1531-7331/10/0804-0243$20.00

    Key Words

    ber-reinforced composites, particle-reinforced composites, layeredmaterials, strength, ductility, stiffness

    Abstract

    In metal matrix composites, a metal is combined with another, often non-metallic, phase to produce a novel material having attractive engineeringattributes of its own. A subject of much research in the 1980s and 1990s, thisclass of materials has, in the past decade, increased signicantly in variety.Copper matrix composites, layered composites, high-conductivity compos-ites, nanoscale composites, microcellularmetals, and bio-derived compositeshave been added to a palette that, ten years ago, mostly comprised ceramicber or particle-reinforced lightmetals togetherwith somewell-establishedengineering materials, such as WC-Co cermets. At the same time, researchon composites such as particle-reinforced aluminum, aided by novel tech-niques such as large-cell 3-D nite element simulation or computed X-raymicrotomography, has served as a potent vehicle for the elucidation of themechanics of high-contrast two-phase elastoplastic materials, with implica-tions that range well beyond metal matrix composites.

    243

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    MMC: metal matrixcomposite

    INTRODUCTION

    Metals and alloys are generally produced and shaped in bulk form but can also be intimately com-bined with another material that serves to improve their performance: The resulting material is ametal matrix composite (MMC). This class of composites encompasses many different materialsthat can be distinguished according to their base metal (e.g., aluminum, copper, titanium); ac-cording to the other, reinforcement, phase (e.g., bers, particles, whiskers); or according to theirmanufacturing process (e.g., powder metallurgy, diffusion bonding, inltration, stir casting).

    Bulk metals and alloys are economical high-performance materials. Why, then, combine thesewith another phase, as doing sowill always add cost and cause complications (in recycling, notably)?Among the stronger drivers of MMC technology are the following basic facts.

    The rst is that the composite approach to materials design makes it possible to go beyondboundaries drawn in property space by basic attributes of the main materials classes. A classicalexample is the specic modulus of metals, dened as elastic modulus E divided by density :(E/). This parameter is a measure of the performance, in weight-critical deformation-limitedstructural applications, of linear elastic components subjected to uniaxial stress. Now, the mainengineering metals and alloys have roughly the same (E/) 26 MJ kg1. So essentially the onlyway to exceed this limit in a metallic material is to replace a signicant fraction of the metal atomswith a phase made of atoms that are (a) situated in the top rows of Mendeleevs periodic table and(b) strongly bonded to one another. Examples are ceramics such as Al2O3, B4C, or SiC and certainvariants of carbon (e.g., high-modulus carbon bers or diamond).Figure 1 shows another exampleof property boundary transgression made possible by MMC technology.

    The second reason why MMCs are interesting has to do with processing: Making a compositeis the only approach by which a signicant volume fraction of oxide or carbide can be introducedinto some important metals. Iron is very frequentlyand easilyreinforced with a wide arrayof carbides, nitrides, or (more rarely) oxides because carbon, nitrogen, and oxygen are solublein this molten metal. Liquid aluminum, magnesium, and copper, in contrast, have essentiallyno solubility for carbon. Therefore, the only way to introduce a carbide into these metals is bymaking a composite; the same holds for aluminum with oxides or nitrides. In other words, MMCtechnology holds the key, for aluminum, magnesium, or copper, to much of the wide spectrum ofmicrostructures and properties available with iron.

    A third reason for interest in MMCs has little to do with metals: Some phases, ceramics inparticular, have far better properties in nely divided form. Notably, micrometer-sized ceramicbers or ceramic particles can be much stronger than bulk ceramics. Additionally, small, single-crystalline ceramic particles can be excellent conductors of heat. Carbon, too, can in nely dividedform be very strong, stiff, and a good conductor of heat (as diamond, for example). Taking advan-tage of this in macroscopic materials therefore calls for the incorporation of such nely dividednonmetallic phases (as bers, platelets, lms, or particles) within a composite material, the ma-trix of which can advantageously be made of metal. Indeed, metals conduct better, are stronger,tougher, and more environmentally resistant than polymersand of course are much tougherthan ceramics.

    These basic considerations have driven sustained research on MMCs, initiated several decadesago by pioneering research such as the important contributions of Anthony Kelly and coworkers(e.g., 6). Research on the subject reached a high level of intensity in the late 1980s and early 1990sand continues today, albeit in a wider array of more distinct directions and hence less visibly.MMCs have also entered the real world of engineering applications, in several forms rangingfrom a few well-established engineering materials (such as WC-Co hard metal) to newer nichematerials; References 13 give recent surveys.

    244 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    0

    2

    4

    6

    8

    10

    12

    14

    16

    18

    20

    0 5 10 15 20 25

    Coefcient of thermal expansion at room temperature (ppm K1)

    Ther

    mal

    con

    duct

    ivit

    y at

    room

    tem

    pera

    ture

    (W c

    m1

    K1

    )

    0.2 mm

    Cu Ag

    Al

    cBNcB

    Diamond

    SiC

    Al-SiC and Cu-Mo

    Area of interest

    Si GaAs

    MetalsCeramicsDiamond composites (Cu matrix, Al matrix, and Ag matrix)

    Figure 1Electronic substrates hold electronic circuits in place and keep them cool. Electronic substrate materialsmust therefore conduct heat well and have a coefcient of thermal expansion (CTE) close to that ofsemiconductors used in electronic circuitry, in the range from roughly 3 ppm K1 to 7 ppm K1. Somemetals (e.g., copper or silver) and some ceramics (e.g., SiC or selected forms of carbon) are good conductorsof heat; however, their CTE falls on either side of the desired range. Because the CTE of metals tends to betoo high and that of ceramics too low, a mixture of the two provides the ideal material for this applicationone of the success stories of MMC technology (14). Aluminum/SiC composites produced by inltration arenow well-established high-performance composites for electronic substrate applications; their propertyrange is indicated in the gure. Carbon materials, however, offer far higher conductivities than does SiC.Over the past decade the price of synthetic diamond, an excellent conductor of heat, has decreased to levelsthat make diamond particles viable engineering materials. A new generation of MMCs combiningaluminum, copper, or silver matrices with diamond particles and featuring an engineered interface has thusemerged, with appropriate CTE values and thermal conductivities approaching 1000 W m1 K1, i.e., 2.5times that of pure copper. Figure adapted from recent work by L. Weber and R. Tavangar at EPFL(Lausanne, Switzerland) (5).

    Thus, the topic ofMMCs is wide-ranging; recent reviews of the subject are in References 2 and7. If we look at progress accomplished during this early twenty-rst century, what rst strikes theeye is that the subject has defocused signicantly to become both broader and less visible as asubtopic in materials science and engineering. There are fewer conferences specically devoted toMMCs, but a rapid look at data from bibliometric search engines indicates that the yearly numberof articles published on the subject has remained roughly steady during this past decade.

    The subject has diversied in two directions. The rst direction is driven by the invention ofinteresting new MMCs; microcellular metals (composites too) and bulk metallic glass composites

    www.annualreviews.org Metal Matrix Composites 245

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    are examples. The other direction has grown out of the realization that these materials serve aswonderful vehicles for the exploration of the physics or the micromechanics of nonlinear multi-phase materials in general. MMCs have thus been the subject of much recent research that hasviewed these as near-ideal model materials, a role that MMCs have served well for many years[going back to one of the earliest papers on the subject (8)].

    We give in what follows a glimpse at some selected areas of recent progress in both of these twodirections. The next section describes new materials and advances in processing, whereas recentprogress in micromechanics driven by MMC research is presented in the section entitled Mech-anisms of Deformation and Fracture. Discussion of MMC research can also be found elsewherein this volume (9).

    PROCESSING AND MATERIALS

    The past ten years have seen a signicant enlargement in the palette of reinforcements that arecombined with metal. New particles have appeared, starting with ne-scale submicrometer (ornano-) particles. These tend to be intrinsically strong while also bringing Orowan hardeningor grain renement to the metallic matrix. The difculty with nanosized reinforcements is inprocessing: Nanoparticles are much harder to incorporate or to distribute uniformly within metal.Capillary forces, often important inMMCprocessing, aremuchhigherwithnanoparticles (becausethese forces scale with the inverse of the reinforcement size) (10). The same holds for carbonnanobers or carbonnanotubes, another newer reinforcementwith potential for the reinforcementof metals.

    Despite the challenges posed in processing, some laboratories and companies have managed tosuccessfully incorporate nanoparticles or nanobers intometal and to produce engineering-quality(i.e., nonporous) MMCs with attractive properties by pressure inltration (11, 12), by stir casting(13), by electrodeposition (14), or by powder metallurgy (15). Another, relatively well-established,pathway to the production of nanoscale MMC structures is by attrition, generally involving ballmilling followed by consolidation. Reference 16 notably reports a cryomilled aluminum-basedMMC having a partly nanoscale microstructure that exhibits, after extrusion and annealing, acompressive yield stress above 1 GPa along the extrusion direction. Other methods that havebeen recently developed to this end are more chemical in nature; these are in situ methods,exemplied by internal oxidation (17). Here, nanoscale reinforcements are created by internalreaction between precursor materials that are nely combined within the composite; Reference18 gives a recent review of in situ MMC processing.

    A few laboratories have explored variations in the intrinsic microstructural quality, rather thanthe scale, of the reinforcement, questioning the wisdom of using low-cost crushed (comminuted)abrasive grade ceramics for the reinforcement ofmetals, as is generally done.Comminutedparticlescontain many internal defects, including cracks or sharp corners along their surfaces. Angularityproduces sites of elevated stress concentration within the composite when it is stressed, causingin turn an acceleration of damage accumulation within the material, which sharply reduces itsductility. Rounding comminuted particles to eliminate such sites of stress concentration has led tosignicant improvements in composite ductility (19, 20). Spectacular improvements in compositeproperties can be further obtained if one uses particles produced by other methods, with fewinternal defects and no sharp angles; a (rare) example of this is Sumitomos SumicorundumTM

    particles (http://www.sumitomochem.co.jp/english/research/develop_basic.html).The wisdom of keeping the volume fractions of ceramic particles below roughly 30%, as

    is usually done to minimize their deleterious inuence on composite ductility, has also beenquestioned. Indeed, the benet of adding ceramic to metal is, for many properties, nonlinear:

    246 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    6 mm

    100 m

    Figure 2Combining metal and ceramic need not produce a brittle material, provided that the ingredients and theprocessing are of high quality. This is illustrated with a four-point bend bar of a composite combiningroughly 50% alumina with 50% aluminum. From current research at EPFL (Lausanne, Switzerland) byA. Hauert, A. Rossoll, and A. Mortensen (21).

    IPC: interpenetratingphase composite

    Adding 25% alumina particles to aluminum will raise the modulus by 50%, from 70 GPa to100 GPa, whereas 60% alumina will yield a 2.5-fold increase to 180 GPa in an isotropic materialhaving a density near that of aluminum. Defect-free composites of this class can be relativelyductile despite a high (50%) ceramic content (see Figure 2). If, in addition, high-quality aluminaparticles are used, both the ultimate tensile strength and the fracture toughness can reach valuesmatching those of engineering aluminum alloys (2225). These results, together with their analysis(see next section), show that the potential held by strong ceramic particles for the reinforcementof metal remains essentially untapped.

    Much innovative recent work has also focused on ceramic reinforcements having three-dimensionally percolating architectures. This is an area that has grown signicantly over thepast decade, largely under the impulse of a parallel thrust in microcellular ceramics research (26).Once inltrated with metal, open-pore microcellular ceramics become interpenetrating phasecomposites (IPCs), dened as composites in which both phases (metal and ceramic in the presentinstance) are three-dimensionally percolating (27). As a result of these advances, IPC-MMCsare now much more frequently produced and explored than they were ten years ago. Note-worthy in this regard are the unique structures that are produced by inltration with metal of

    www.annualreviews.org Metal Matrix Composites 247

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    Growing ice crystals become,after inltration, the (light) metal phase in the composite

    xx

    y

    y

    1 mm

    Suspension of ceramic particles in water becomes, after dryingand sintering, the (dark) ceramic in the composite

    Figure 3Metal matrix composites from freeze-cast ceramic preforms. (Left) Ice crystals are made to grow directionallyin a slurry of water containing a high volume fraction of ne ceramic particles. Particle pushing by thegrowing ice crystals concentrates the ceramic into thin walls. After freeze drying and sintering, a porousceramic preform is obtained; the domain distribution and the spacing of lamellae are functions of slurrysolidication parameters. (Right) A cross section through a freeze-cast aluminareinforced Al-12Si compositeproduced by squeeze casting the metal into pores of the ceramic preform, viewed perpendicular to thefreezing direction in one single domain of a polydomain sample. Micrograph kindly provided by S. Roy andA. Wanner of the University of Karlsruhe, Germany (29).

    PCM: phase changematerial

    freeze-cast ceramics (Figure 3) (28, 29), biomorphic ceramics obtained from pyrolized wood(Figure 4) (3032), or ceramic preforms produced by three-dimensional printing (33).

    Together with the exploration of radically new reinforcement architectures, the past decadehas seen a greater emphasis on the exploration of MMCs for functional applications. Experiencehas shown that many applications of MMCs are motivated by their ability to conduct electricityor heat: Electronic substrates, electrical contactors, and brushes are examples of applications inwhich MMCs excel. Such properties have motivated the exploration of new MMCs for functionalapplications, such as novel carbon-reinforced metals for high thermal conductivity (Figure 1) ornovel composite superconductors (Figure 5) (34).

    New functional MMCs have also emerged from the current drive toward greater energy ef-ciency. A notable example is that of solid-oxide fuel cell anode materials, most frequently a porouscomposite combining nickel with yttria-stabilized zirconia (3537). These are generally producedby blending, densifying, and coring mixtures of NiO and zirconia, followed by reduction ofthe NiO; the ensuing (25%) shrinkage of NiO creates the pore network. Cell performance ishighly dependent on the microstructure, and hence on the processing, of these complex anodemetal/ceramic/gas composites. One can thus expect these to remain a focus of intense researchactivity in the years to come.

    The current drive toward energy research should motivate the exploration of new MMCs; asomewhat exotic example is phase change materials (PCMs). These materials can serve in ther-mal management by absorbing or releasing heat as they melt or solidify, respectively (38). Aclassical PCM is parafn, the melting point of which is near ambient temperature (the melting-point temperature varies with the precise parafn formulation). The efciency of PCMs is often

    248 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    Figure 4Computed X-ray microtomography composite view of three orthogonal sections of an Al/SiC compositeproduced by pressure inltration with an Al-13Si-9Mg alloy of a three-dimensional SiC honeycomb-likestructure made by reaction with Si of pyrolized beech wood. The bounding box measures approximately750 m per side; the voxel size is 1.46 m. In the (X-ray attenuationbased) color scale used, the Al-lledpores appear blue, the SiC appears yellow or black, and residual porosity appears red or black. Image kindlyprovided by T.E. Wilkes and K.T. Faber of Northwestern University, Evanston, Illinois; for details consultReference 30.

    restricted by their capacity to transport heat to/from the melting/solidication front, that is, bytheir low heat conductivity. As a result, some of the best PCMs are composites combining thephase-changing material (say, parafn) with another, more conductive phase (generally a metal).The resulting MMC-PCM can be made by inltrating pores of an open-cell microcellular metalwith the molten PCM.

    Microcellular metals, often called metal foams, are also MMCs. Research on highly porousmetals has grown in recent years to become a major thrust in metallurgy, covered by dedicatedconferences and books (and is now too broad to be covered in any detail within the present article)(39, 40; http://www.metfoam2009.sav.sk/index.php?ID=1859&pg=13).

    www.annualreviews.org Metal Matrix Composites 249

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    aa

    c b

    a

    c b

    50 m

    100 m

    Figure 5Cross-polarized light micrograph of a composite consisting of MgB2 continuous bers within a Mg matrix(a). The 190-m-diameter MgB2 bers are created by a reaction of 140-m B bers with liquid Mg underthermal cycling conditions (ten 600900C cycles over 3 h). The inset shows a higher-magnication view ofa similarly reacted ber (eleven 650900C cycles over 4.5 h) highlighting (b) the MgB2 grains and (c) theW-B core of the ber. Image kindly provided by J.D. DeFouw and D.C. Dunand of NorthwesternUniversity, Evanston, Illinois (34).

    BMG: bulk metallicglass

    MMC research has also expanded in recent years by incorporation of the approach into othercurrent areas of metallurgical research: Many major innovations in metallurgical research havebranched into novel MMC research. Bulk metallic glasses (BMGs) are inherently very brittlematerials; the MMC approach has proven to be a potent pathway toward addressing this limita-tion. Siegrist & Lofer (41), for example, have shown recently that if soft particles are combinedwith a BMG matrix, signicant improvements in BMG (compressive) ductility can be achievedat minimal loss in yield stress. In related work, novel metals available in powder form, such asaluminum-based BMG (42) or quasicrystals (43), have been explored as reinforcements for alu-minum. Novel metallurgical processes, such as severe plastic deformation or friction stir welding,have also been adapted toward the processing of MMCs, notably as methods toward improvingthe spatial uniformity of reinforcement distribution (4447).

    Current interest in layered structures has motivated research on MMC multilayers at both themicro- and nanoscale. Figure 6 shows a metal/metal microlaminate material combining ductileaustenitic and brittle martensitic steel grades. In such composites, themore ductile metal stabilizesthe more brittle metal against tensile failure. As a result, as-quenched martensite can be coachedto deform by more than 20% in tension without breaking. Through use of this approach, withappropriately strong interfaces, sufciently small layer thicknesses, and optimized heat treatment,a steel sheet having an ultimate tensile strength of 1.35 GPa with a tensile fracture elongation of28% was demonstrated at the University of Tokyo (48). Nanoscale laminates (Figure 7) can alsoexhibit interesting properties; these materials serve notably as vehicles for research on plasticitysize effects or the role of interfaces in the deformation and fracture of ne-scale materials moregenerally (49, 50).

    As for ber-reinforced metals, recent engineering progress has been in large part drivenby 3Ms innovations in high-quality ceramic bers suitable for the reinforcement of metals.Work during the past decade has notably introduced a continuous wire of aluminum rein-forced by Nextel 610TM alumina bers designed for the overhead transmission of electrical

    250 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    200 m

    Figure 6Multilayered steel composite combining strongly bonded sheets of austenitic SS304 (0.04C-0.53Si-0.92Mn-8.07Ni-18.19Cr; lighter phase in the micrograph) and martensitic SS420J2 (0.34C-0.49Si-0.57Mn-0.12Ni-13.21Cr) steel. The composite is produced by stacking 25 layers of 1-mm-thick surface-ground steel sheets,sealing the stack by welding, preheating in inert gas, and hot rolling to a nal thickness of approximately 3mm. After annealing and air cooling, the laminate is further thinned by cold rolling to a thickness of 1.0 mm.This particular composite exhibits a yield stress of 450 MPa, an ultimate tensile strength of 1250 MPa, and20% elongation at fracture. Micrograph kindly provided by S. Nambu and T. Koseki of the University ofTokyo, Japan (48).

    power (shown in Figure 8) (http://solutions.3m.com/wps/portal/3M/en_US/Energy-Advanced/Materials/Industry_Solutions/MMC/).

    The past decade has seen progress in our understanding of the fundamentals that underlieMMC processing. Noteworthy are advances in our understanding of in situ processes (18), of thewetting of ceramics by metals (good overviews of this topic can be found in References 51 and52), of transport phenomena that intervene in processes such as inltration (53, 54), and of thelink between deformation processing and particle clustering in solid-state MMC processing (seenext section).

    Finally, we have seen impressive and far-reaching advances inmicrostructural characterization.These developments have proven particularly well suited for MMCs because of the high contrast(both physical and mechanical) that can exist between phases in these materials. Advances in X-rayand neutron diffraction characterization of materials have thus largely beneted MMC research(55, 56), as has the advent of methods for the characterization of material microstructures inthree dimensions, including computed X-ray microtomography (Figures 4 and 9) (30, 5759)and automated serial sectioning (Figure 10) (60).

    MECHANISMS OF DEFORMATION AND FRACTURE

    From the structural viewpoint, a main limitation to the industrial application of MMCs has beenthe embrittlement associatedwith the addition, to themetal, of brittle ceramic reinforcements.Thephysical phenomena that control this behavior occur at the micrometer scale and above inMMCs.

    www.annualreviews.org Metal Matrix Composites 251

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    +5.000e+02+4.167e+02+3.333e+02+2.500e+02+1.667e+02+8.333e+01+1.526e058.333e+011.667e+022.500e+023.333e+024.167e+025.000e+02

    Maximum princi-pal stress (MPa)

    +2.000e+02+1.833e+02+1.667e+02+1.500e+02+1.333e+02+1.167e+02+1.000e+02+8.333e+01+6.667e+01+5.000e+01+3.333e+01+1.667e+01+0.000e+00

    S22 (MPa)

    Multilayers/Si interface

    1

    2

    a

    b

    2

    500 nm

    1

    500 nm

    Si substrate

    Pt

    Al/SiC multilayers

    1 m

    21

    Figure 7(a) Nanolayered composite of aluminum and SiC produced by magnetron sputtering onto a silicon substrate,tested by nanoindentation. The nominal thickness of each of the alternating Al and SiC layers is 50 nm. TheAl layers are polycrystalline with a columnar grain structure, and the SiC material is amorphous. The pictureon the left shows a scanning electron microscope image of a cross section of the postindented compositeprepared by the focused ion beam technique. A part of the Berkovich indentation mark behind the sectionedsurface is visible. One can see that a symmetric pattern of damage was caused by the indentation, comprisingshear fracture of (1) the SiC layers and (2) mid-level voids. Further below, cracking near the multilayers/substrate interface has also occurred. (b) The color contour plots show the results from a nite elementanalysis of nanoindentation on the multilayered structure. The model features axial symmetry about the leftvertical boundary. The material system is identical to that used in the experiment. The left gure shows thedistribution of normal stress along the vertical (indentation) direction. Directly underneath the indentation,the stress eld is predominately compressive. The contour legend was adjusted to bring out the fact thatthere is a region, below and slightly outside the indentation edge, that is under signicant tensile stress. Thisregion largely corresponds to the damage zone observed in the experiment as highlighted. The right contourplot of maximum principal stress further indicates a particularly highly stressed region near the interfacebetween the Al/SiC multilayers and the Si substrate, which can also explain the observation of interfacecracks. Adapted from gure kindly provided by N. Chawla of Arizona State University, Tempe, Arizona, andY.L. Shen of the University of New Mexico, Albuquerque, New Mexico (50).

    252 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    3M aluminum fiber core

    Figure 83Ms unidirectional Nextel 610TM nanocrystalline alumina berreinforced pure-aluminum composite has,along the ber direction, roughly one-third the conductivity of copper in combination with a tensile strengthof roughly 1.5 GPa and a density near 3 g cm3 (http://solutions.3m.com/wps/portal/3M/en_US/Energy-Advanced/Materials/Industry_Solutions/MMC/). When used instead of steel as thehigh-strength core of electrical power transmission cables (inset), the composite provides an attractivesolution to power transmission, for example, in environmentally sensitive river crossings such as thatdepicted in this gure. The composite features low sag and improved conductance and allows new towerconstruction to be avoided while boosting transmission capacity. Photographs courtesy of 3M CorporateCommunications, St. Paul, Minnesota.

    DD: discretedislocation

    FE: nite element

    As mentioned above, these phenomena can now be observed and quantied accurately usingnovel three-dimensional microstructural characterization techniques. In addition, deformationand failure processes within MMCs can now be simulated using several novel tools and methods,including discrete dislocation (DD) dynamics, large-scale nite element (FE) simulation, andnonlinear homogenization theory. Driven by this combination of strong engineering motivationand novel methods, research on the nonlinear deformation and fracture of MMCs has led tosignicant advances in this general area during the past decade.

    Particle-Reinforced Composites

    The dispersion of stiff ceramic particles or bers within a ductile metallic matrix leads to an in-crease in ow stress of the metal by load transfer across a strong interface from the matrix to thereinforcement. Constraint imposed by the ceramic reinforcements on matrix plastic deformationinduces large tensile hydrostatic stresses in the matrix. This enhances the load carried by the rein-forcements and hence the composite ow stress but also triggers the early development of internaldamage in the form of particle fracture, interface decohesion, and/or matrix void growth (6164).

    www.annualreviews.org Metal Matrix Composites 253

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    0.3 mm

    Pure-aluminum matrix Harder aluminum alloy matrix

    Lower strainlevel

    Higher strainlevel

    Figure 9X-ray microtomographic in-situ observation of the evolution of damage at different strain levels in a modelcomposite material made of aluminum-based matrices reinforced with 4 vol% of ZrO2/SiO2. The gureshows tomographic slices extracted parallel to the tensile axis (vertical), at various levels of stress, increasingfrom top to bottom. (Left column) Damage in the model composite material made of a pure-aluminum matrixis mainly by decohesion along the particle/matrix interface. (Right column) The same material as in the leftcolumn, but with a harder aluminum alloy matrix. The damage mechanism changes to particle fracture. Inboth cases, initiation, growth, and coalescence of damage can be captured. Images kindly provided byE. Maire and V. Carmona, MATEIS Laboratory, INSA Lyon, France (57).

    254 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    Figure 10Three-dimensional nite element model corresponding to a region 200 140 60 m wide based on theactual microstructure of a composite of 6061 reinforced by 27 vol% SiC particles. The model containsapproximately 1000 SiC particles. The three-dimensional microstructure of this powder metallurgyprocessed material was generated via automated (robotic) serial sectioning and optical imaging, using theRobo-Met.3DTM device (60). The red feature is an extended region of higher-than-average equivalentplastic strain generated by applying a 2.5% tensile strain parallel to the long dimension, showing that themacroscopic deformation band is modied by the presence of the local heterogeneities in the spatialarrangements of the particles. Image kindly provided by J. Spowart of the Air Force Research Laboratory,Wright-Patterson Air Force Base, Ohio.

    RVE: representativevolume element

    The challenge to nd how the microstructure of these materials can be tailored to improve theirductility and toughness has been addressed through a combination of simulation and experiment.

    Realistic quantitative predictions of the mechanical response of particle-reinforced compos-ites can be obtained via computational micromechanics. The composite behavior is analyzedthrough the FE simulation of a three-dimensional representative volume element (RVE) of themicrostructure. The RVE size has to exceed a critical value to ensure that the simulation resultsare independent of both the RVE size and the spatial distribution of the reinforcements withinthe RVE. This strategy has been widely used to explore the effect of reinforcement volume frac-tion, spatial distribution, and shape on deformation and damage mechanisms of such composites(6572). This approach is illustrated in Figure 11a, which shows a cubic RVE containing a non-homogeneous distribution of ceramic spheres dispersed in an aluminum matrix. Upon tensiledeformation, the ceramic particles constrain matrix plastic deformation within the cluster, whichincreases hydrostatic stresses in both thematrix and the particles (Figure 11b). These large stressesin turn promote interface decohesion (Figure 11c) as well as particle fracture (66) and/or matrixductile failure by void growth (67).

    Such damage mechanisms reduce the strain hardening capacity of the material. This reductionin turn precipitates the onset of plastic instability, which often controls the tensile ductility ofthese materials (73, 74), to low strain values (

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    a b

    GPa1.00.80.60.40.20.0

    c

    Figure 11Three-dimensional nite element simulation of the effect of particle clustering on the deformation anddamage micromechanisms in a model composite made of 15 vol% of ceramics spheres embedded in analuminum matrix (71). (a) Sphere spatial distribution within the cubic representative volume element (RVE)of the microstructure. Notice that the microstructure is periodic and that spheres are truncated where theyintersect the cube faces and reappear on the opposite sides of the cube. The spheres are grouped in clustershaving a higher local volume fraction of reinforcements (one of these is highlighted in dark blue). (b) Contourplot of the maximum principal stress in the ceramic particles when the composite has been subjected to atensile strain of 5%. Very large tensile stresses develop in particles within the clusters. (c) Development ofdamage by interface decohesion (marked with black arrows on a two-dimensional cut through a large RVE).Decohesion is localized between particles situated very close to each other within the clusters and orientedalong the loading direction. Interfacial fracture relieved large stress concentrations generated at the interfaceby this particle spatial distribution. The blue arrows in panels b and c indicate the direction of tensile loading.From research at the Polytechnic University of Madrid, Spain, by J. Segurado, C. Gonzalez, and J. Llorca.

    growth and coalescence through the matrix, can now be followed directly within the material(see Figure 9).

    These advances in experimental characterization have been accompanied by new developmentsin linear and nonlinear homogenization models. Linear homogenization is a proven methodologyto determine the effective properties of composite materials as a function of the phase propertiesand their spatial distribution. For instance, accurate approximations to the elastic constants of

    256 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    particle-reinforced isotropic composites were obtained byTorquato (80) by truncating after third-order terms an exact expansion series for the effective stiffness tensor, the rst few terms ofthe series being given as a function of statistical correlation parameters that describe the phasearrangement (81). Extension to the plastic regime was not, however, immediate, and the accuracyof the predictions was limited by the localization of strain during plastic deformation and by thelimitations of the incremental methods (either tangent or secant) used to linearize the nonlinearproblem (8284). Large stress and strain gradients develop during the elastoplastic deformationof composites, especially with elastic particles embedded in a soft matrix. The plastic behavior ofthe matrix is determined by a reference equivalent stress computed in the classic homogenizationmodels from the volumetric average of the matrix stress tensor. The appropriate equivalent stressis, however, signicantly lower than the phase average of the equivalent stress, and hence thecomposite yield and ow stresses are overestimated using the classic homogenization approach.This problem has since been overcome by the so-called modied secant approximation, shown tobe equivalent to a variational estimate by Ponte Castaneda (85, 86) and amenable to simplicationinto relatively user-friendly expressions (87). In this approach, the reference equivalent stressin the matrix is determined from the volumetric average of the second-order moment of thestress tensor in this phase instead of the usual rst-order moment (or average), an approximationthat takes into account the effect of the eld uctuations (strain localization). The accuracy ofthis new homogenization model was demonstrated by comparisons with quasi-exact numericalresults obtained through computational micromechanics (88, 89), and new versions of the tangentapproach also yielded good results (90, 91) (Figure 12).

    These nonlinear homogenization approaches have served to develop physically based phe-nomenological models that include the effect of damage nucleation and growth (by either particlefracture or interface decohesion), addressing damage percolation as well (83, 92, 93, 96). These

    0

    50

    100

    150

    200

    0 0.01 0.02 0.03 0.04 0.050

    50

    100

    150

    200

    250

    0 0.01 0.02 0.03 0.04 0.05Tensile strain

    Tens

    ile s

    tres

    s (M

    Pa)

    Tensile

    Shear

    Sphericalparticles

    Matrix

    Tensile/shear strain

    Tens

    ile/s

    hear

    str

    ess

    (MPa

    )

    a b

    Matrix

    Ellipsoidalparticles

    Figure 12Predicted stress-strain curve for an aluminum matrix composite reinforced with 25 vol% stiff ceramicparticles. (a) Tensile ( purple) and shear ( green) deformation of a composite reinforced with sphericalparticles. (b) Tensile deformation parallel (black) and perpendicular (blue) to the ellipsoidal reinforcements ina composite with aligned ellipsoidal reinforcements with an aspect ratio of 3. The solid circles correspond toquasi-exact numerical results obtained from computational micromechanics by averaging the resultsobtained in 12 different particle realizations. The continuous lines denote the homogenization resultsprovided by improved secant (spheres) and incremental (ellipsoids) methods (89, 91).

    www.annualreviews.org Metal Matrix Composites 257

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    models can be divided in two groups. The rst is applicable to composites having a low particlevolume fraction (

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    transition in tensile failure mode as the reinforcement volume fraction and/or the matrix strengthincrease, which has been reported experimentally (24, 93, 95) and is captured by a recent model(96).

    The analyses presented above predict an effect of the particle size on the tensile strength andthe ductility because smaller particles tend to be stronger. This in turn diminishes the extentof particle fracture during composite deformation and increases the hardening rate in tension.Prior to the onset of particle fracture, however, for a given elastoplastic matrix, predictions ofthe composite initial ow stress and hardening rate are insensitive to particle size, if all else isconstant. These predictions differ from experimental ndings (97100), which show an increasein the yield stress and hardening rate as the particle size decreases, particularly for interparticledistances below 10 m.

    This plasticity size effect has been rationalized in terms of the strain gradients that appearin the matrix as a result of deformation incompatibility between the plastic matrix and the stiffceramic particles. For a given geometry of plastic ow, ner microstructures (shorter interparticlespacing) lead to greater strain gradients in the matrix, both during composite deformation and,before this, due to differential matrix/reinforcement thermal contraction during cooldown fromprocessing temperatures. Higher gradients in turn produce a greater density of geometricallynecessary dislocations, which harden the metal. The effect has been known for some time (100);however, its analysis has progressed signicantly in recent years. Detailed models of the effect ofinterparticle distance of the ow stress of composites have been carried out using DD simulations(101103). Figure 13 gives results from a fully three-dimensional coupled DD-FE simulationof dislocation ow between narrowly spaced parallel ceramic bers. The increase in ow stressand work hardening rate as the interparticle distance decreases essentially takes, in the ne-scalestructures of this simulation, the form of a classical Orowan bowing mechanism. In addition,the accumulation of dislocations at the particle interface during plastic ow creates an internalstress larger than the resolved applied stress and of opposite sign near the interface, reducing theeffective interparticle distance formatrix plastic ow from d to deff (Figure 13c). This phenomenoncauses further hardening by what is, in effect, a source-shortening mechanism. In recent years

    Figure 13Coupled dislocation dynamicsnite element (DD-FE) simulations of the effect of interparticle distance onthe ow stress of a continuously reinforced Al-Al2O3 composite deformed perpendicularly to the bers.(a) Simulated dislocation microstructure projected on the (001) plane of the aluminum matrix, which isperpendicular to the axis of the bers. The volume fraction of bers is 45%. Longitudinal strain 33 =0.16% applied along the vertical direction in the gure ([010] direction for the aluminum). Note theaccumulation of dislocations at the interfaces and in the channels with smallest width. (b) Size effect intransverse stress-strain curves for different reinforcement volume fractions (5%, 10%, and 45%); straining isalong the same direction as in panel a. The elementary simulation cells have the same size and contain thesame initial dislocation density. The solid red lines show the size effect predicted by the coupled discrete-continuum model. The dashed blue lines represent continuum FE predictions using, for the aluminummatrix, a stress-strain response tted to a coupled DD-FE simulation of the single crystal. (c) Resolved shearstress prole ( , normalized by the shear modulus of aluminum, Al) across the aluminum matrix in thecomposite with the highest reinforcement volume fraction (45%) and the smallest spacing between bers (inunits of x/b, where b is the Burgers vector) for the most active slip system in the matrix. The deformationconditions are the same as in panel a. The dashed black line is a prole extracted from simulation data, andthe solid black line is the corresponding regression curve. The accumulation of dislocations at the interfacesinduces a resistive internal stress larger than the resolved applied stress, which reduces the channel width d toan effective value deff . Figure kindly provided by L. Kubin of the CNRS-ONERA, Chatillon, France, andadapted with permission from Elsevier Science; full publication of this work is in Reference 102.

    www.annualreviews.org Metal Matrix Composites 259

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    2

    MPa With particle fracture

    No particle fracture

    a b

    Crack growth direction

    No particlefracture

    Particles havefractured

    1250110095080060045030015010.3

    Antishielding

    No particle fracture

    Shielding

    With particle fracture 1.2

    1.1

    1.0

    0.9

    0.8

    0.7

    0.6

    0.5

    0.4

    k I(A

    ISiC

    ) / k

    I(cp)

    Projected crack length, a (m)

    Applied stressof 7 MPaApplied stressof 14 MPa

    0 40 80 120 160

    Figure 14Two-dimensional nite element simulation of crack growth in a microstructure produced on the basis of micrographs of a SiCparticlereinforced aluminum composite. (a) Color contours of the stress state in a two-dimensional image of a microstructure (toppanel: without particle fracture; bottom panel: with particle fracture). Several particles have cracked away from the crack tip. (b) Thepredicted crack proles. As has been observed experimentally, when the particles crack, the crack prole is quite linear, with the crackpropagating through the particles. When the particles do not crack, crack deection is more pronounced. The bottom plot of panel bshows the local stress intensity factor calculated at various points in the microstructure. This is plotted as a ratio of the mode I stressintensity for the actual microstructure, kI(AlSiC), normalized by that of a homogeneous model with circular particles (with the cracknot interacting with the particles), kI(cp). Thus, a value of less than 1 indicates crack shielding (a decrease in the driving force for crackgrowth), whereas a value greater than 1 indicates antishielding (an increase in the driving force for crack growth). Drawn from gurekindly provided by N. Chawla of Arizona State University, Tempe, Arizona (108).

    investigators have tackledplasticity size effects, using approaches basedonhigher-order continuummicromechanics formulations incorporating one or more length scales to account for the role ofstrain gradients or compliant interfaces on the matrix ow behavior (104, 105).

    Fracture mechanisms have also been the subject of continued investigation. The inuence ofthe particle distribution has been quantied and modeled in three dimensions, showing a stronginuence on damage accumulation within these materials (Figure 10) (60, 106, 107). Micromech-anisms governing the fracture toughness of these materials have also received attention in recentyears in simulation (Figure 14) (108) and also in experiment, where progress has notably beendriven by the advent of quantitative fractographic analysis tools (109, 110). High fracture tough-nesses have been demonstrated in gas-inltrated Al-Al2O3 composites containing a high volumefraction (approximately 50%) of ceramic particles. When reinforced with strong polygonal Al2O3particles, these composites present strength/toughness combinations that rival those of engineer-ing aluminum alloys. The surprisingly high toughness of these composites comes about by thesynergistic contribution to the fracture energy of several factors, namely, the increase in elasticmodulus (which is 2.5 times that of the unreinforced alloy), the formation of a large plastic zonearound the crack tip, and high bridging stresses between crack surfaces carried by the metal liga-ments as a result of the small interparticle distance and high local stress triaxiality (2325, 110, 111).

    260 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    GLS: global loadsharing

    LLS: local loadsharing

    SCF: stressconcentration factor

    Finally, current interest in Cu-C composites as heat sinks in microelectronics has led to newanalytical and numerical models to predict their thermal conductivity. New developments includethe inuence of the polyhedral reinforcement geometry and spatial distribution as well as theinuence of the crystalline orientation and of the electron/phonon interfacial conduction barrier(112114).

    Fiber-Reinforced Composites

    In continuous parallel ber-reinforced composites, progressive ber fracture controls the longi-tudinal tensile strength. Two extreme situations can be found. Under global load sharing (GLS)conditions, the effect of the local stress concentration around the broken bers is negligible: Loadshed by fractured bers is redistributed equally among the intact bers in the remaining cross-sectional area of the composite at that location. The stress-strain curve then exhibits a smoothmaximum, which arises from the competition between (a) hardening induced by matrix and berdeformation and (b) softening caused by ber fragmentation. Under these assumptions, elegantanalytical solutions (115118) and numerical models (119) have been developed to predict thecomposite strength, accounting for matrix/ber load transfer and ber fracture statistics.

    GLS, however, represents an idealization because it ignores damage localization. Evidence ofdamage localization inMMCs is provided by in situmonitoring of damage usingX-ray synchrotronradiation in a Ti/SiC composite tested in tension (120): Fiber fracture is localized near the fracturesurface, whereas most of the sample remains free of damage. In addition, GLS predicts failurewhen the tangent modulus reaches zero and does not account for size effects; both predictions areopposed to available experimental results in most ber-reinforced MMCs (121123).

    Experimental evidence indicates that local stress concentrations around broken bers tend tolocalize damage, leading to fracture at lower strengths by the unstable expansion of a cluster ofbroken reinforcements (120123). This behavior can be captured by local load sharing (LLS)models, which rely on a stress concentration function (SCF) describing the redistribution ofload around a broken ber, which governs the neighboring ber fracture probability (124127).Although elegant solution approaches exist, LLS models tend to be more complex and often relyon numerical simulations to compute the composite strength. Model predictions are sensitive tothe precise values of the SCF, which in turn depends on the actual ber arrangement as well asthe interface and matrix properties. Accurate values for the SCF were obtained in specic MMCsystems using detailed FE simulations of the stress eld around a broken ber. These ndingswere in turn used in rigorous experimental validations of LLS predictors of MMC strength (122,124, 128, 129).

    From the modeling viewpoint, a more complex problem is to determine the strength of ber-reinforced MMCs in the presence of a hole or a sharp notch. Two main failure mechanisms havebeen reported, depending on matrix and interface properties and on thermal residual stresses(130132). With a ductile matrix having a high ow stress and good ber/matrix bonding, failuretakes place by the propagation of a mode I crack from the notch root perpendicular to the bersat moderate toughness levels. Composites with a weak, brittle matrix and/or a poor ber/matrixbond exhibit a strong tendency toward mode II crack propagation along the ber direction. Suchsplitting initiates and propagates at relatively high values of the applied stress intensity factor,leading to a low notch sensitivity for this class of composites.

    Simulation of the behavior of notched specimens was initially carried out for SiCmonolamentreinforced titanium within the framework of cohesive crack models, as matrixplastic deformation is localized in a thin strip in front of the notch. There, bers fracture andare eventually pulled out from the matrix (131, 132). More recently, novel multiscale simulation

    www.annualreviews.org Metal Matrix Composites 261

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    M

    D a0

    lx

    lylx

    ly

    y

    x

    P

    P/2 P/2L

    Da0

    a0

    h

    P

    M

    QQ

    Homogenized material

    FibersMatrix

    h

    CMOD (m)

    SimulationExperiments

    3PL/

    2 BD

    2 (M

    Pa)

    0 50 100 150 200 250 3000

    200

    400

    600

    800 a0/D = 0.3525oC

    a b

    cd

    0.100.080.060.040.020.00

    GPa

    4.03.02.01.00.0

    1.0

    Figure 15Multiscale modeling of fracture in SiC berreinforced Ti.6A-4V matrix composites. (a) Schematic of the three-point bend testcomprising a notched beam showing the central region of length h used in the numerical simulations, together with the detailedmicrostructure in the central region of the notched beam ( planar view and lateral view). Matrix, bers, and homogenized material areshown in different shades of gray. (b) Comparison of simulated and experimental P-CMOD (loadcrack mouth opening displacement)curves for the notched beam tested at 20C. The initial notch length a0 was given by a0/D = 0.35, where D = beam height. The loadP on the ordinate of the plot was normalized by the beam dimensions (L = beam length between outer load application points, B =beam width, and D = beam height). (c) Contour plot of the accumulated plastic strain in the matrix at maximum load in the compositebeam tested at 20C. The black line shows the initial notch tip. (d) Idem for the longitudinal stress in the bers. From research at thePolytechnic University of Madrid and IMDEA-Materials by C. Gonzalez & J. Llorca (135).

    262 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    strategies based on embedded cell models in three dimensions were used to predict the toughnessand notch sensitivity of ber-reinforced MMCs (133). The representation of the material in frontof the notch tipwhere damage is concentrated-includes the actual ber/matrix topology inthe composite, whereas the rest of the solid is modeled as a linear thermoelastic, transversallyisotropic homogeneous solid (Figure 15a). Damage and fracture micromechanisms that controlfracture (namely, plastic deformation of the matrix, brittle ber fracture, and ber/matrix fric-tional sliding) are all included in the simulation. Fiber fracture is modeled by introducing interfaceelements randomly placed along the bers and with random strengths to simulate ber fracturerealistically. It is assumed that the interface strength is negligible and that the ber/matrix in-teraction is controlled by friction. Micromechanical parameters governing the behavior of bers,matrix, and interfaces are independently measured. The mechanical response of the test beams inthree-point bending is then computed using the FE method, leading to results that are in goodagreement with experimental data, at both the microscopic level and the macroscopic level andfrom room temperature up to 400C (Figure 15b,c) (134, 135). These results demonstrate the po-tential of coupled multiscale three-dimensional simulation for predicting the fracture behavior ofMMCs.

    Other than ber-reinforced titanium composites, recent research has addressed alumina berreinforced aluminium. Damage micromechanisms in tension (136) and fatigue (137), matrix hard-ening mechanisms (138), and the properties of complex composite architectures (139, 140) havebeen investigated.

    CONCLUSION

    Thus, a highly diverse picture of MMCs emerges from this brief overview of current researchon this materials class. First, the materials are more numerous than was the case ten years ago(although the same probably cannot be said of processes). Second, the toolkit available to the ma-terials scientist for the elucidation of structure/property relations in these interesting high-phasecontrast materials has expanded signicantly in both experimental and analytical tools togetherwith underlying theory. Third, the range of explored properties has also expanded to include, forexample, a greater focus on thermal conductivity, a property for which MMCs are now amongthe top-performing bulk materials.

    We expect this trend toward breadth and diversity to continue.Many new, interestingmaterialsare bound to be composites that combine a metal with another phase. As one example, MMCs,full of metal/dielectric interfaces as these materials are, may one day enter the eld of opticalmaterials research. PCMs, mentioned above, are another class of emerging materials likely to becomposites with a metallic matrix. MMCs are a class of materials with a rich, albeit complicated,future.

    SUMMARY POINTS

    1. MMC research has branched into many new directions, and the range of materials itencompasses has expanded signicantly.

    2. Several new classes of MMCs have gained importance and have been studied in detailin the past ten years, including interpenetrating phase composites, biomorphic ceramic-reinforced metals, bulk metallic glass composites, nanoscale composites, layered metals,and microcellular metals.

    www.annualreviews.org Metal Matrix Composites 263

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    3. Research on MMCs for structural applications has progressed along two main direc-tions: (a) the exploration of new composites expanding the property range of MMCs and(b) the elucidation of structure/property relations in particulate and ber MMCs.

    4. Research onMMCs for functional applications has seen signicant progress on materialsdesigned for thermal management.

    5. MMCresearch has been, and remains, an important vehicle in nonlinearmicromechanicsand three-dimensional microstructural characterization.

    6. Our understanding of damage and fracture mechanisms in ceramic-reinforced metals,both brous and particulate, now enables the accurate prediction of their performanceand the denition of strategies for their optimization.

    7. The potential offered by strong ceramic particles for the reinforcement of metals is veryhigh and remains untapped.

    FUTURE ISSUES

    1. With an increased drive toward energy saving, research on MMCs for structural appli-cations will surely gain new momentum, given the weight savings these materials offerin several critical applications. The accuracy of the modeling tools in establishing theconnection between microstructure and properties will be very useful in developing newmaterials with optimal properties.

    2. For the same reason, many new composites combining a metal with another phase, oftenone of ceramic, will likely emerge for applications in the management, storage, andgeneration of energy as well as in novel functional applications.

    3. A revitalization of research on the fundamentals of MMC processing, over and above theinvention of new systems, would be opportune.

    DISCLOSURE STATEMENT

    The authors are not aware of any afliations, memberships, funding, or nancial holdings thatmight be perceived as affecting the objectivity of this review.

    ACKNOWLEDGMENTS

    A.M. gratefully acknowledges support of his research on the subject at EPFL from core laboratoryfunding and from the Swiss National Science Foundation (project number 200020-107556), atMIT from the Ofce of Naval Research and the U.S. National Science Foundation, and in bothinstitutions from several industrial sponsors. J.L. acknowledges support from the Comunidadde Madrid (program ESTRUMAT), the Spanish Ministry of Science and Innovation (projectMAT2009-14396), and several industrial sponsors.

    264 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    LITERATURE CITED

    1. Evans A, SanMarchi C, Mortensen A. 2003. Metal Matrix Composites in Industry: An Introduction and aSurvey. Dordrecht, Neth.: Kluwer Acad. 423 pp.

    2. Chawla N, Chawla KK. 2006. Metal Matrix Composites. New York: Springer Verlag. 401 pp.3. Miracle DB. 2005. Metal matrix compositesfrom science to technological signicance. Compos. Sci.

    Technol. 65:2526404. Chung DDL, Zweben C. 2000. Composites for electronic packaging and thermal management. In

    Comprehensive Composite Materials, Vol. 6: Applications, ed. MG Bader, K Kedwards, Y Saweda, pp. 70125 (Ch. 6.38). Oxford, UK: Pergamon

    5. Weber L, Tavangar R. 2009. Diamond-based metal matrix composites for thermal management: poten-tial and limits. Adv. Mater. Res. 59:11115

    6. Kelly A, Davies GJ. 1965. The principles of the ber reinforcement of metals. Metall. Rev. 10:1777. Clyne TW. 2000. Comprehensive Composite Materials, Vol. 3: Metal Matrix Composites. Oxford UK:

    Pergamon. 842 pp.8. Zwilsky KM, Grant NJ. 1957. Copper-silica and copper-alumina alloys of high temperature interest.

    Trans. AIME J. Metals 9:11972019. Embury JD, Bouaziz O. 2010. Steel-based composites: driving forces and classications. Annu. Rev.

    Mater. Res. 40:in press10. MortensenA, Jin I. 1992. Solidication processing ofmetalmatrix composites. Int.Mater. Rev. 37:1012811. Karnesky RA,MengL,DunandDC. 2007. Strengtheningmechanisms in aluminum containing coherent

    Al3Sc precipitates and incoherent Al2O3 dispersoids. Acta Mater. 55:129930812. Uozumi H, Kobayashi K, Nakanishi K, Matsunaga T, Shinozaki K, et al. 2008. Fabrication process of

    carbon nanotube/light metal matrix composites by squeeze casting. Mater. Sci. Eng. A 495:2828713. Honma T, Nagai K, Katou A, Arai K, Suganuma M, Kamado S. 2009. Synthesis of high-strength

    magnesium alloy composites reinforced with Si-coated carbon nanobres. Scr. Mater. 60:4515414. Zimmerman AF, Palumbo G, Aust KT, Erb U. 2002. Mechanical properties of nickel silicon carbide

    nanocomposites. Mater. Sci. Eng. A 328:1374615. Thakur SK, Srivatsan TS, Gupta M. 2007. Synthesis and mechanical behavior of carbon nanotube-

    magnesium composites hybridized with nanoparticles of alumina. Mater. Sci. Eng. A 466:323716. Ye J, Han BQ, Lee Z, Ahn B, Nutt SR, Schoenung JM. 2005. A tri-modal aluminum based composite

    with superhigh strength. Scr. Mater. 53:4818617. Meijering J. 1971. Internal oxidation in alloys. In Advances in Materials Research, ed. H Herman,

    pp. 181. New York: Wiley-Interscience18. Tjong SC, Ma ZY. 2000. Microstructural and mechanical characteristics of in situ metal matrix com-

    posites. Mater. Sci. Eng. Rep. R 29:4911319. Qin S, Chen C, Zhang G, Wang W, Wang Z. 1999. The effect of particle shape on ductility of SiCp

    reinforced 6061 Al matrix composites. Mater. Sci. Eng. A 272:3637020. Spowart JE, Miracle D. 2003. The inuence of reinforcement morphology on the tensile response of

    6061/SiC/25p discontinuously reinforced aluminum. Mater. Sci. Eng. A 357:1112321. Hauert A. 2009. Damage propagation and fracture in highly reinforced particulate metal matrix composites.

    Doctoral thesis (EPFL thesis no. 4333). Ecole Polytech. Fed. Lausanne22. Kouzeli M, Weber L, Marchi CS, Mortensen A. 2001. Inuence of damage on the tensile behavior of

    pure aluminum reinforced with40 vol. pct. alumina particles.ActaMater. 49:3699709. Erratum. 2003.Acta Mater. 51:649396

    23. Miserez A, Mueller R, Mortensen A. 2006. Increasing the strength/toughness combination of highvolume fraction particulate metal matrix composites using an Al-Ag matrix alloy. Adv. Eng. Mater. 8:5662

    24. Miserez A, Mortensen A. 2004. Fracture of aluminum reinforced with densely packed ceramic particles:inuence of matrix hardening. Acta Mater. 52:533145

    25. Miserez A,Muller R, Rossoll A,Weber L,Mortensen A. 2004. Particle reinforcedmetals of high ceramiccontent. Mater. Sci. Eng. A 38789:82231

    www.annualreviews.org Metal Matrix Composites 265

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    26. Green DJ, Colombo P. 2003. Cellular ceramics: intriguing structures, novel properties, and innovativeapplications. Mater. Res. Soc. Bull. 28:296300

    27. Clarke DR. 1992. Interpenetrating phase composites. J. Am. Ceram. Soc. 75:7395928. Deville S, Saiz E, Nalla RK, Tomsia AP. 2006. Freezing as a path to build complex composites. Science

    311:5151829. Roy S,Wanner A. 2008.Metal/ceramic composites from freeze-cast ceramic preforms: domain structure

    and elastic properties. Compos. Sci. Technol. 68:11364330. Wilkes TE, Stock SR, DeCarlo F, Xiao X, Faber KT. 2009. X-ray microcomputed tomography of beech

    wood and biomorphic C, SiC and Al/SiC composites. Philos. Mag. 89:13738931. Wilkes TE, Pastor JY, Llorca J, Faber KT. 2008. Mechanical properties of wood-derived silicon carbide

    aluminum-silicon-magnesium composites as a function of temperature. J. Mater. Res. 23:17324332. Herzog A, VogtUF, Siegmann S, Beffort O. 2006. Aluminummetal matrix composites based on biomor-

    phic silicon carbide. Adv. Eng. Mater. 8:9808333. San Marchi C, Kouzeli M, Rao R, Lewis JA, Dunand DC. 2003. Alumina-aluminum interpenetrating-

    phase composites with three-dimensional periodic architecture. Scr. Mater. 49:8616634. DeFouw JD, Dunand DC. 2008. Mechanisms and kinetics of MgB2 synthesis from boron bers. Acta

    Mater. 56:57516335. Sun C, Stimming U. 2007. Recent anode advances in solid oxide fuel cells. J. Power Sources 171:2476036. Goodenough JB,Huang Y-H. 2007. Alternative anodematerials for solid oxide fuel cells. J. Power Sources

    173:11037. Brandon NP, Brett DJ. 2006. Engineering porous materials for fuel cell applications. Philos. Trans. R.

    Soc. London Ser. A 364:1475938. Mehling H, Cabeza LF. 2008. Heat and cold storage with PCM: an up to date introduction into basics

    and applications. Heidelberg: Springer. 308 pp.39. AshbyMF, Evans A, Fleck NA, Gibson LJ, Hutchinson JW,Wadley HNG. 2000.Metal Foams: A Design

    Guide. Boston: Butterworth Heinemann. 251 pp.40. Degischer HP, Krizt B, eds. 2002. Handbook of Cellular Metals. Weinheim, Ger.: Wiley-VCH. 373 pp.41. Siegrist ME, Lofer JF. 2007. Bulk metallic glass-graphite composites. Scr. Mater. 56:10798242. Scudino S, Surreddi K, Sager S, Sakaliyska M, Kim J, et al. 2008. Production and mechanical properties

    of metallic glass-reinforced Al-based metal matrix composites. J. Mater. Sci. 43:45182643. ElKabir T, Joulain A, Gauthier DS, Bonneville JDB. 2008. Hot isostatic pressing synthesis and mechan-

    ical properties of Al7Al-Cu-Fe composite materials. J. Mater. Res. 23:9041044. Spowart JE, Ma ZY, Mishra RS. 1993. The effect of friction stir welding on spatial heterogeneity of

    discontinuously-reinforced aluminum microstructures. In Friction Stir Welding and Processing II, ed. KVJata, M Mahoney, R Mishra, pp. 24352. Warrendale, PA: TMS

    45. Slipenyuk A, Kuprin V, Milman Y, Spowart JE, Miracle DB. 2004. The effect of matrix to reinforce-ment particle size ratio (PSR) on the microstructure and mechanical properties of a P/M processedAlCuMn/SiCp MMC. Mater. Sci. Eng. A 381:16570

    46. Sabirov I, Kolednik O, Pippan R. 2005. Homogenization of metal matrix composites by high pressuretorsion. Metall. Mater. Trans. 36A:286170

    47. Sabirov I, Kolednik O, Valiev RZ, Pippan R. 2005. Equal channel angular pressing of metal matrixcomposites: effect on particle distribution and fracture toughness. Acta Mater. 53:491930

    48. Nambu S, Michiuchi M, Inoue J, Koseki T. 2009. Effect of interfacial bonding strength on tensileductility of multilayered steel composites. Compos. Sci. Technol. 69:193641

    49. Verdier M, Huang H, Spaepen F, Embury JD, Kung H. 2006. Microstructure, indentation and workhardening of Cu/Ag multilayers. Philos. Mag. 32:500916

    50. Chawla N, Singh D, Shen YL, Tang G, Chawla K. 2008. Indentation mechanics and fracture behaviorof metal/ceramic nanolaminate composites. J. Mater. Sci. 43:438390

    51. Sobczak N, Singh MJ, Asthana R, eds. 2005. Themed issues: high-temperature capillarity and interfacialphenomena. Curr. Opin. Solid State Mater. Sci. 9(45):149254

    52. Louis E, Mortensen A, Eustathopoulos N, Kostorz G. 2008. Int. Conf. High Temp. Capillarity, 5th, 2007,Alicante, Spain. Mater. Sci. Eng. A 495(12):1342

    266 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    53. Michaud V, Mortensen A. 2001. Inltration processing of ber reinforced composites: governing phe-nomena. Composites A 32:98196

    54. Vasic S, Grobety B, Kuebler J, Kern P, Graule T. 2008. Experimental models for activtation mechanismof pressureless inltration in the non-wetting steel-alumina MMC system. Adv. Eng. Mater. 10:47175

    55. Thilly L, Renault PO, Vidal V, Lecouturier F, Van Petegem S, et al. 2006. Plasticity of multiscalenanolamentary Cu/Nb composite wires during in situ neutron diffraction: codeformation and sizeeffect. Appl. Phys. Lett. 88:191906

    56. Roy S, Gibmeier J, Wanner A. 2009. In situ study of internal load transfer in a novel metal/ceramiccomposite exhibiting lamellar microstructure using energy dispersive synchrotron X-ray diffraction.Adv. Eng. Mater. 11:47177

    57. Maire E, Carmona V, Courbon J, Ludwig W. 2007. Fast X-ray tomography and acoustic emission studyof damage in metals during continuous tensile tests. Acta Mater. 55:680615

    58. Borbely A, Kenesei P, Biermann H. 2006. Estimation of the effective properties of particle-reinforcedmetal-matrix composites from microtomographic reconstructions. Acta Mater. 54:273544

    59. Requena G, Fiedler G, Seiser B, Degischer P, Di Michiel M, Buslaps T. 2009. 3D-quantication of thedistribution of continuous bres in unidirectionally reinforced composites. Composites A 40:15263

    60. Spowart JE. 2006. 3-Danalysis of discontinuously-reinforced aluminumcompositemicrostructures usingautomated serial sectioning. JOM 58:2933

    61. Llorca J, Needleman A, Suresh S. 1991. An analysis of the effects of matrix void growth on deformationand ductility in metal-ceramic composites. Acta Metall. Mater. 39:231735

    62. Llorca J, Martin A, Ruiz J, Elices M. 1993. Particulate fracture during deformation of a spray formedmetal-matrix composite. Metall. Trans. 24A:157588

    63. Singh PM, Lewandowski JJ. 1993. Effects of heat treatment and reinforcement size on reinforcementfracture during tension testing of a SiCp discontinuously reinforced aluminum alloy. Metall. Trans.24A:253143

    64. Whitehouse AF, Clyne TW. 1993. Cavity formation during tensile straining of particulate and shortber metal matrix composites. Acta Metall. Mater. 41:170111

    65. Bohm HJ, Eckschlager A, Han W. 2002. Multi-inclusion unit cell models for metal matrix compositeswith randomly oriented discontinuous reinforcements. Comput. Mater. Sci. 25:4253

    66. Segurado J, Gonzalez C, Llorca J. 2003. A numerical investigation of the effect of particle clustering onthe mechanical properties of composites. Acta Mater. 51:235569

    67. Llorca J, Segurado J. 2004. Three-dimensional multiparticle cell simulations of deformation and damagein sphere-reinforced composites. Mater. Sci. Eng. A 365:26774

    68. Shen H, Lissenden CJ. 2005. Stress and strain localization in three-dimensional modeling for particlereinforced composites. Metall. Mater. Trans. A 36:165360

    69. Chawla N, Ganesh VV. 2006, Wunsch B. 2004. Three-dimensional (3D) microstructure visualizationand nite elementmodeling of themechanical behavior of SiC particle reinforced aluminum composites.Scr. Mater. 51:16165

    70. SunCJ, Saffari P, SadeghipourK, BaranG. 2005. Effects of particle arrangement on stress concentrationsin composites. Mater. Sci. Eng. A 405:28795

    71. Segurado J, LLorca J. 2005. A computational micromechanics study of the effect of interface decohesionon the mechanical behavior of composites. Acta Mater. 53:493142

    72. Segurado J, LLorca J. 2006. Computational micromechanics of composites: the effect of particle spatialdistribution. Mech. Mater. 38:87383

    73. Brockenbrough JR, Zok FK. 1995. On the role of particle cracking in ow and fracture of metal matrixcomposites. Acta Metall. Mater. 43:1120

    74. Gonzalez C, LLorca J. 1996. Prediction of the tensile stress-strain curve and ductility in Al/SiC com-posites. Scr. Mater. 35:9197

    75. Chawla N, Sidhu RS, Ganesh VV. 2006. Three-dimensional visualization and microstructure-basedmodeling of deformation in particle-reinforced composites. Acta Mater. 54:154148

    76. Borbely A, Csikor FF, Zabler S, Cloetens P, Biermann H. 2004. Three-dimensional characterization ofthe microstructure of a metal-matrix composite by holotomography. Mater. Sci. Eng. A 367:4050

    www.annualreviews.org Metal Matrix Composites 267

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    77. Babout L,Maire E, Fougeres R. 2004. Damage initiation in model metallic materials: X-ray tomographyand modelling. Acta Mater. 52:247587

    78. Babout L, Maire E, Bufe`re J-Y, Fouge`res R. 2001. Characterization by X-ray computed tomography ofdecohesion, porosity growth and coalescence in model metal matrix composites. Acta Mater. 49:205563

    79. Geandier G, Hazotte A, Denis S, Mocellin A, Maire E. 2003. Microstructural analysis of aluminachromium composites by X-ray tomography and 3-D nite element simulation of thermal stresses.Scr. Mater. 48:121924

    80. Torquato S. 1998. Effective stiffness tensor of composite media. II. Applications to isotropic dispersions.J. Mech. Phys. Solids 46:141140

    81. Segurado J, LLorca J. 2002. A numerical approximation to the elastic properties of sphere-reinforcedcomposites. J. Mech. Phys. Solids 50:210721

    82. Ponte Castaneda P, Suquet P. 1998. Nonlinear composites. Adv. Appl. Mech. 34:17130183. Gonzalez C, LLorca J. 2000. A self-consistent approach to the elasto-plastic behavior of two-phase

    materials including damage. J. Mech. Phys. Solids 48:6759284. Chaboche JL,KanouteLP,RoosA. 2005.On the capabilities ofmean-eld approaches for the description

    of plasticity in metal matrix composites. Int. J. Plast. 21:14093485. Suquet P. 1995. Overall properties of nonlinear composites: a modied secant moduli theory and its link

    with Ponte Castanedas nonlinear variational procedure. C. R. Acad. Sci. Paris Ser. IIb 320:5637186. PonteCastaneda P. 1991. The effectivemechanical properties of nonlinear isotropic composites. J.Mech.

    Phys. Solids 39:457187. Mueller R, Mortensen A. 2006. Simplied prediction of the monotonic uniaxial stress-strain curve of

    non-linear particulate composites. Acta Mater. 54:21455588. Segurado J, LLorca J, Gonzalez C. 2002. On the accuracy of mean-eld approaches to simulate the

    plastic deformation of composites. Scr. Mater. 46:5252989. Gonzalez C, Segurado J, LLorca J. 2004. Numerical simulation of elasto-plastic deformation of com-

    posites: evolution of stress microelds and implications for homogenization models. J. Mech. Phys. Solids52:157393

    90. Doghri I,OuaarA. 2003.Homogenizationof two-phase elasto-plastic compositematerials and structures.Study of tangent operators, cyclic plasticity and structures. Int. J. Solids Struct. 40:1681712

    91. Pierard O, Gonzalez C, Segurado J, Llorca J, Doghri I. 2007. Micromechanics of elasto-plastic materialsreinforced with ellipsoidal inclusions. Int. J. Solids Struct. 44:694562

    92. Gammage J, Wilkinson D, Brechet Y, Embury D. 2004. A model for damage coalescence in heteroge-neous multi-phase materials. Acta Mater. 52:525563

    93. Poole WJ, Charras N. 2005. An experimental study on the effect of damage on the stress-strain behaviorfor Al-Si model composites. Mater. Sci. Eng. A 406:3008

    94. Mueller R, Rossoll A, Weber L, Bourke MAM, Dunand DC, Mortensen A. 2008. Tensile ow stress ofceramic particle reinforced metal in the presence of particle cracking. Acta Mater. 56:440216

    95. Beffort O, Long S, Cayron C, Kuebler J, Buffat PA. 2007. Alloying effects on microstructure and me-chanical properties of high volume fraction SiC-particle reinforced Al-MMCs made by squeeze castinginltration. Compos. Sci. Technol. 67:73745

    96. Hauert A, Rossoll A, Mortensen A. 2009. Ductile-to-brittle transition in tensile failure of particle-reinforced metals. J. Mech. Phys. Solids 57:47399

    97. Kamat SV, Rollett AD, Hirth JP. 1991. Plastic deformation in Al-alloy matrix-alumina particulate com-posites. Scr. Metall. Mater. 25:2732

    98. Mummery P, Derby B. 1991. The inuence of microstructure on the fracture behavior of particulatemetal matrix composites. Mater. Sci. Eng. A 135:22124

    99. Kouzeli M, Mortensen A. 2002. Size dependent strengthening in particle reinforced aluminum. ActaMater. 50:3951

    100. Calhoun RB, Dunand DC. 2000. Dislocations in metal matrix composites. In Comprehensive CompositeMaterials, Vol. 3: Metal Matrix Composites, ed. TW Clyne, pp. 2759 (Ch. 3.02). Oxford, UK: Pergamon

    101. Cleveringa HH, Van Der Giessen E, Needleman A. 1997. Comparison of discrete dislocation andcontinuum plasticity predictions for a composite material. Acta Mater. 45:316379

    268 Mortensen Llorca

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa

    ded

    from

    ww

    w.a

    nnua

    lrevi

    ews.o

    rgby

    Cin

    vesta

    v de

    l IPN

    on

    01/2

    7/12

    . For

    per

    sona

    l use

    onl

    y.

  • MR40CH10-Mortensen ARI 24 May 2010 15:28

    102. Groh S, Devincre B, Kubin LP, Ross A, Feyel F, Chaboche JL. 2005. Size effects in metal matrixcomposites. Mater. Sci. Eng. A 400 401:27982

    103. Broedling NC, Hartmaier A, Buehler MJ, Gao H. 2008. The strength limit in a bio-inspired metallicnanocomposite. J. Mech. Phys. Solids 56:1086104

    104. Ma H, Hu GK. 2006. Inuence of bers shape and size on overall elastoplastic property for micropolarcomposites. Int. J. Solids Struct. 43:302543

    105. Chen H, Liu XN, Hu GK. 2008. Overall plasticity of micropolar composites with interface effect. Mech.Mater. 40:72128

    106. Wilkinson DS, Pompe W, Oeschner M. 2001. Modeling the mechanical behavior of heterogeneousmulti-phase materials. Prog. Mater. Sci. 46:379405

    107. Spowart JE. 2006. Microstructural characterization and modeling of discontinuously-reinforced alu-minum composites. Mater. Sci. Eng. A 425:22537

    108. Ayyar A, ChawlaN. 2007.Microstructure-basedmodeling of the inuence of particle spatial distributionand fracture on crack growth in particle-reinforced composites. Acta Mater. 55:606473

    109. Sabirov I, Duschlbauer D, Pettermann HE, Kolednik O. 2005. The determination of local conditionsfor void initiation in front of a crack tip for materials with second phase particles. Mater. Sci. Eng. A393:27585

    110. Miserez A, Rossoll A, Mortensen A. 2004. Fracture of aluminum reinforced with densely packed ceramicparticles: link between the local and the total work of fracture. Acta Mater. 52:133751

    111. Miserez A, Rossoll A, Mortensen A. 2004. Investigation of crack-tip plasticity in high volume fractionceramic particle reinforced metal matrix composites. Eng. Frac. Mech. 71:2385406

    112. Nogales S, Bohm HJ. 2008. Modeling of the thermal conductivity and thermomechanical behavior ofdiamond reinforced composites. Int. J. Eng. Sci. 46:60619

    113. Flaquer J, Rios A, Martn-Meizoso A, Nogales S, Bohm HJ. 2007. Comput. Mater. Sci. 49:15663114. Tavangar R, Molina JM, Weber L. 2007. Assessing predictive schemes for thermal conductivity against

    diamond reinforced silver matrix composites at intermediate phase contrast. Scr. Mater. 56:35760115. Curtin WA. 1991. Theory of mechanical properties of ceramic-matrix composites. J. Am. Ceram. Soc.

    74:283745116. Curtin WA. 1993. Ultimate strengths of ber-reinforced ceramics and metals. Composites 24:98102117. Hui CY, Phoenix SL, Ibnabdeljalil M, Smith RL. 1995. An exact closed form solution for fragmentation

    of Weibull bers in a single lament composite with applications to ber-reinforced ceramics. J. Mech.Phys. Solids 43:155185

    118. Weber CH, Chen X, Connell SJ, Zok FW. 1994. On the tensile properties of a ber reinforced titaniummatrix composite. I. Unnotched behavior. Acta Metall. Mater. 42:344350

    119. Bednaryck BA, Arnold SM. 2001. New local failure model with application to the longtitudinal tensilebehavior of continuously reinforced titanium composites with local debonding. Compos. Sci. Technol.61:70529

    120. Maire E, Owen A, Bufe`re J-Y, Withers PJ. 2001. A synchrotron X-ray study of a Ti/SiCf compositeduring in situ straining. Acta Mater. 49:15363

    121. Ramamurty U, Zok FW, Leckie FA, Deve HE. 1997. Strength variability in alumina ber-reinforcedaluminum matrix composites. Acta Mater. 45:460313

    122. Gonzalez C, Llorca J. 2001. Micromechanical modelling of deformation and failure in Ti-6Al-4V/SiCcomposites. Acta Mater. 49:350519

    123. Gundel DB, Wawner FE. 1991. Interfacial reaction kinetics of coated SiC bres with various titaniumalloys. Scr. Metall. Mater. 25:43741

    124. Foster GC, Ibnabdeljalil M, Curtin WA. 1998. Tensile strength of titanium matrix composites: directnumerical simulations and analytic models. Int. J. Solids Struct. 35:252336

    125. Curtin WA. 1999. Stochastic damage evolution and failure in ber-reinforced composites. Adv. Appl.Mech. 36:163253

    126. Landis CM, Beyerlein IJ, McMeeking RM. 2000. Micromechanical simulation of the failure of berreinforced composites. J. Mech. Phys. Solids 48:62148

    127. Pradhan S, Chakrabarti BK, Hansen A. 2005. Crossover behavior in a mixed-mode ber bundle model.Phys. Rev. E 71:036149

    www.annualreviews.org Metal Matrix Composites 269

    Ann

    u. R

    ev. M

    ater

    . Res

    . 201

    0.40

    :243

    -270

    . Dow

    nloa