Metal Cutting Saw RS 200 + RS 230

Ergonomically designed handle

Motor with high-performance gear box

Bajonet-snap buckle for blade cover

Solid base plateAutomatically retracting blade guard

Lateral rip fence for straight cuts

Continuously adjustable mitres up to 45° (with 5 locking positions)

Cut indicator

B/54

BALFRA Rotaspeed® – Metal Cutting Saw RS 200 + RS 230Hand operated

Theidealmachineforworksiteandworkshop,foralmostburr-freecuttingwithoutcooling.

Forfastandcleancutsinpipes,threadedrods,profiles,wireducts,corru-gatedandtrapezoidalsheets,sandwichpanels,drymortarlessconstructionprofilesandmanymore.

Advantages at a glance:■ 1700Watthigh-performancemotorforexactcutswithoutcoolant.■ Fastandeasychangeofsawblade.■ Continuouslyadjustablecuttingdepthto67mmatRS200 and82mmatRS230.■ Thebasebladeisadjustableformitrecutsupto45°.■ Chipcollector.■ Theidealmachineforsiteassemblycompanies,facadebuilders,repair

shops,locksmitheries,rackbuilders,roofers,boothbuilders,weldingshops,plumbingandheatingcontractors.

■ Ideallyapplicable,whereanglegrindersaren´tstrongenoughorcleanenough.

■ Idealforweldpreparationbymitrecutting.

ALFRA RotaSpeed® RS 200

Sawbladediameter: 200mm(8”)Sawbladearbor: 30/25.4/20mmPower: 1700WattsSpeed,rpm: 3700Mitre: 0-45°Cuttingcapacitymm0°: 67Cuttingcapacitymm45°: 42Max.materialthickness(dependingonmaterial): 6mmVoltage: 230-50/60HzWeight: 6.3kg

Prod.-No.AlfraRotaSpeed®RS200 22400

ALFRA RotaSpeed® RS 230

Sawbladediameter: 230(9”)Sawbladetoolholder: 30/25.4/20mmPower: 1700WattsSpeed,rpm: 2600Mitre: 0-45°Cuttingcapacitymm0°: 82Cuttingcapacitymm45°: 56Max.materialthickness(dependingonmaterial): 6-8mmVoltage: 230-50/60HzWeight: 7.1kg

Prod.-No.AlfraRotaSpeed®RS230 22410

Scope of Supply:Machinewith2TCTSawBlades(premiumquality),OperationManual,RipFence,SetofTools,DistancesleeveforSawBladeArbor,incardboardbox.

Wereservetherighttomaketechnicalchanges.

B/55

BALFRA Circular Saw Blades – RotaSpeed®

ALFRA-RotaSpeed® TCT Circular Saw Blades. • Made in Germany

Magnetic Chip Remover

Inastainlesssteelroundrod,youcanmoveamagnetbackandforth.Thestrongmagnetpicksupmetalchips–pullaknobandthechipsfalloff.Formorecleanlinessintheworkplace.

Prod.-No.ALFRAMagneticChipRemover,Length400mm 18654

Prod.-No. 18654

■ Tungstencarbidetipped,suitableformetalcuttingsawsfrom: ALFRA,Flex,Euroboor,Evolution,Hitech,Jepson,Metallkraft,Ridgid,etc.

■ ThesespecialTCTcircularsawsensurefastandcleancutsinpipes,threadedrods,profiles,corrugatedandtrapezoidalsheets,wireducts,sandwichpanels,drymortarlessconstructionprofiles,fasteningprofiles(DINrails),gratesusingdrycuttingmethod.

■ Foruseonmetals,CrNisteel*,aluminium.

■ Highcuttingperformanceandtoollife.Theexcellentprice/performanceratiomakesthesesawshighlyeconomical.

■ Thecorrespondingmanufacturer'smachineguidelinesandnotesonusemustbeobservedwhenusingthesesawblades.

Premium QualityCutting Ø mm Application Dimensions mm No. of teeth Prod.-No.

180/7“ Steel* 180x20 34 22205180/7“ Aluminium 180x20 48 22206

200/8“ Steel* 200x20 42 22255200/8“ Aluminium 200x20 54 22256200/8“ fortrapezoidalsheets200x20 68 22257 230/9“ Steel* 230x25.4 48 22305230/9“ Aluminium 230x25.4 62 22306230/9“ fortrapezoidalsheets230x25.4 80 22307

*Withstainlesssteel,thetoollifewillbelowerinrelationtothematerialthickness.Packagingunit=1piece

B/56

BALFRA RotaDry® – Drycutter 355

Arguments which are convincing in quality, performance and pricing:■ Foralmostburr-freecuttingofprofilesandpipesoutofsteel,iron, copper,brass,aluminium,plastics,compositesandstainlesssteel withoutcooling.■ Applicatione.g.insteelconstruction,cabinetmaking,interiorfittingsetc.■ Withdepthfenceforaccuratecutting■ Angleandparallelstopperformitrecutsupto45°■ Witharemovablechipcollectingsump■ Witharboradjustmentforchangingthesawblades■ Easytotransport

ALFRA RotaDry® 355

Sawbladediameter 355mmMotor 230V/50HzInput 2200WSpeed 1300rpmCuttingcapacity90° 13mmwallthickness 180x105mmCuttingcapacity90° 13mmwallthickness 120x120mmCuttingcapacity90° 13mmwallthickness 135mmCuttingcapacity45° 13mmwallthickness 110x100mmCuttingcapacity45° 13mmwallthickness 100x100mmCuttingcapacity45° 13mmwallthickness 105mmWeight 23kg

Prod.-No.AlfraRotaDry®355,with1TCTSawBlade72T(teeth) 22420

Spare TCT Circular Saw Blades also suitable for cutting-off machines, such as:

Jepson/Global/Ridgid/Ryobi

TheuniversalTCTsawbladeforfastcuttingof:steel – copper – aluminium– profiles– cable – sheet metal – solid material

■ withoutcoolant■ Regrindable■ Lownoiseduetolaserornaments

Deliverable dimensions Steel Stainless steel* Prod.-No.

305x2.2x25.4 60T • – 32100305x2.2x25.4 80T • • 32101355x2.6x25.4 72T • – 32104355x2.6x25.4 80T • • 32103355x2.6x25.4 90T • • 32102

355x2.6x25.4 90T coated 32105Othertoothcountsuponrequest.

*Withstainlesssteel,thetoollifewillbelowerinrelationtothematerialthickness.

Prod.-No. 22420

355 x 2.6 x 25.4 • 90 T • coated

B/57

B

RBX 180 HV

RBX 120 HV

B/58

BPortable Band Saw Machines for Professionals

There is a variety of portable band saw ma-chines, but only a few of them are suitable for industrial applications or at a construction site.Pricing is usually being more important than reliability and durability.

Our new machines have an excellent price-per-for-mance-ratio and are setting new standards. The robust and compact design makes it ideal for handling in the machine shop or the construc-tion site.

Ideally qualified for locksmiths, plumbing, metal-, heating-, pipeline- and mechanical workshops. Also for construction companies, public utilities with or without mobile workshops, power sta-tions, schools, technical learning and teaching facilities.

Special Features:

• Portable • Mobile • Change from horizontal or vertical cutting within seconds. With help of the vertical sec-

tion notches or contours can be cut out easily from radius 85 mm on.

• For vertical section 0 - 45 ° stepless • Very fast band saw blade-change, as the chan-

ge is on the front side • Cutting pressure adjustment in 4 steps, mat-

ched to the material cross section • Safe material clamping due to quick-vice appli-

cation • Robust high-performance single-phase-motor• 4-fold ball bearings-blade guide RBX 120 HV • 8-fold ball bearings-blade guide RBX 180 HV • Adjustable ball bearings-blade guide for angular cutting

B/59

BALFRA Band Saw Machine

RBX 120 HVTwistfree

sawingframe–precisionmilled

Bandsawclamp

Transportationwheels

Drivewheel–gummed

4-foldballbearings-bladeguide

Carryhandle

Handle

Quickvice45°to90°

AutomaticOFF-switch

B/60

BALFRA Band Saw Machine – RBX 120 HV

OurportableBandSawMachineRBX120HVcutsreliablygaspipesandconduitsaswellasthinwalledpipesmadeofstainlesssteel,constructionsteel,aluminiumandPVC.Furthermoreit’sparticularlysuitableforcuttingflatandprofiledmaterials.

90° Ø 120mm;4-3/4” 105mm;4-1/8”

l 60mm;3-3/8”

45° Ø 50mm;2” 50mm;2”

TechnicalData:Inductionmotor,capacity 400WattsPower 230VCuttingspeed 40.5m/min-1–50Hz 49.0m/min-1–60HzFeed AutomaticCuttingpressureadjustment: 4stepsMitre 0-45°Bandsawmeasurements 1430x13x0.65mm;56-1/3”x1/2”x0.025”

90° Ø 120mm;4-3/4” 105mm;4-1/8”

l 60mm;3-3/8”

45° Ø 50mm;2” 50mm;2”ED: 40%Soundlevel 75dB(A)(duringno-loadoperation)Unitsize(mm) length780,width340,high335Weight: 35kg;77lbs

StandardAccessories:• PortableBandSawMachineRBX120HV–230V(110Vondemand)• HSSBi-MetalBandsawblade• Operatorprotectionplug• Toolkit• Operationmanual

Prod.-No.Band Saw Machine RBX 120 HV 22500

Special Accessories Enlarged saw table 150 x 100 mm; 6” x 3-15/16” 22523

Replacement Band Saw Blades HSS-Bi-Metal1430 x 13 x 0.65 mm; 56-1/3” x 1/2” x 0.025”

HSS Bi-Metal 10 tpi IPU = 10 pcs 22510


HSS Bi-Metal 6/10 tpi IPU = 10 pcs 22512



B/61

BALFRA Band Saw Machine

RBX 180 HV

Cleaningbrushforself-cleaning

theblade

AutomaticOFF-switch

Twistfreesawingframe–precisionmilled

Bandsawclamp

Transportationwheels

Drivewheel–gummed

8-foldballbearings-bladeguide,

adjustable

High-performancesingle-phase-

motor

Optional:Chainviceforpipesandprofiles(90°only)

Bladeadjustmentpossibilityforwork

onsmallitems

B/62

BALFRA Band Saw Machine – RBX 180 HV

OurBandSawMachineRBX180HVfeaturesalltechnicaladvantagesofthesmallonebutwithextendedcapacity:

90° Ø 180mm,7” 150mm;6”

45° Ø 80mm,3-5/32” 80mm,3-5/32”

Thestandardquick-clampingflatvicecanbechangedintoachainvicewithinseconds.Thereforebigdiametertubescanbeclampedtightlyandmachined.

TechnicalData:Inductionmotor,capacity 380WattsPower 230VCuttingspeed 40.5m/min-1–50Hz 49.0m/min-1–60HzFeed AutomaticCuttingpressureadjustment 4stepsMitre 0-45°withquickclampflatvice; 90°withchainviceBandsawmeasurements: 1625x13x0,65mm;64”x1/2”x0.025”

90° Ø 180mm,7” 150mm;6”

45° Ø 80mm,3-5/32” 80mm,3-5/32”ED: 40%Soundlevel 75dB(A)(duringno-loadoperation)Unitsize(mm) length865,width335,high415Weight 41kg,90lbswithchainvice; 46kg,101lbswithquickclampflatvice

StandardAccessories:• PortableBandSawMachineRBX180HV–230V(110Vondemand)• Quickclampflatvice• 2piecesHSSBi-MetalBandsawblades (onesawbladeisstoredsafelyinsideprotectioncover)• Operatorprotectionplug• Toolkit• Operationmanual

Prod.-No.Band Saw Machine RBX 180 HV 22520

Chain vice 22522

Special accessories Enlarged saw table 150 x 100 mm; 6” x 3-15/16” 22523

Replacement Band Saw Blades HSS-Bi-Metal1625 x 13 x 0.65 mm; 64” x 1/2” x 0.025”






Cuttingpressureadjustable

Chainvice(optional)

B/63

ALFRA RBX Band Saw Machines in Action

Mitre Saw up to 45 ° RBX 120 HV + 180 HV

Automatic OFF Switch RBX 120 HV + 180 HV

Enlarged saw table

Quick viceRBX 180 HV

Cleaning brush RBX 180 HV

Vertical cutting, here with extended support surface, RBX 120 HV + 180 HV

Clamped pipe in chain vice RBX 180 HV

Changeable chain vice in action RBX 180 HV

Change from quick vice to chain vice within seconds – RBX 180 HV

B/64

Features:■ M42

■ High concentricity

■ With solid base plate, thus more threads and higher stability as well as concentric running ex-

actness.

■ For material from 2 mm – with positive chipping and cutting angles as well as combi-toothing 4/6 tpi.

This variable spacing provides a more even cut, for a minor generation of vibrations and heat. Lower expen-diture of energy when cutting.

■ Cutting Depth: 38 mm (1 1/2“).

■ Lateral slots help to remove the core.

■ Suitable for unalloyed steel (up to 700 N/mm2), nonferrous metals, light metals, plastics, gypsum,

pulp wood- and plywood boards, lightweight building boards and

general wood processing.

■ Drill bit exchangeable with other commercially available arbors.

HSS-Bi-Metal Hole SawSALFRA

B/104

Also steel/stainless steel up to approx. 3 mm, can be wor-ked easily (for frequent use, we recommend our TCT Hole Saws).

… tailored to work on softwoods.

HSS-Bi-Metal Hole SawSXXWItHXCOBALt-ALLOyEdXtEEtHX(M42)

B/105

BALFRAHSS-Bi-MetalHoleSawsareapplicableinportableandpillardrillingmachines.Whenusingpillardrillingmachines,usemanualfeedonly.

Features:■ M42■ Highconcentricity.■ Withsolidbaseplate,thusmorethreadsandhigherstabilityaswell

asconcentricrunningexactness.■ Withpositivechippingandcuttinganglesaswellascombi-toothing4/6

tpi.Thisvariablespacingprovidesamoreevencut,foraminorgenera-tionofvibrationsandheat.Lowerexpenditureofenergywhencutting.

■ CuttingDepth:38mm(11/2“).■ Lateralslotshelptoremovethecore.■ Suitableforunalloyedsteel(upto700N/mm2),nonferrousmetals,light

metals,plastics,gypsum,pulpwood-andplywoodboards,lightweightbuildingboardsandgeneralwoodprocessing.

■ Drillbitexchangeablewithothercommerciallyavailablearbors.

Tip:Startdrillingoperationwithlightpressure.Continuewithlightandsteadypressure,avoidpendulummotion,followthespeedchart,usecoolant.Whencuttingwoodorwoodsubstitutes,removedrilldustintime.

Saw-Ø mm Inch Prod.-No.

14.0 9/16 0500014

16.0 5/8 0500016

17.0 11/16 0500017

19.0 3/4 0500019

20.0 15/19 0500020

21.0 13/16 0500021

22.0 7/8 0500022

24.0 15/16 0500024

25.0 1 050002527.0 11/

16 0500027

29.0 11/8 0500029

30.0 13/16 0500030

32.0 11/4 0500032

33.0 15/16 0500033

35.0 13/8 0500035

37.0 17/16 0500037

38.0 11/2 0500038

40.0 19/16 0500040

41.0 15/8 0500041

43.0 111/16 0500043

44.0 13/4 0500044

46.0 113/16 0500046

48.0 17/8 0500048

51.0 2 050005152.0 21/

16 0500052

54.0 21/8 0500054

57.0 21/4 0500057

59.0 25/16 0500059

60.0 23/8 0500060

64.0 21/2 0500064

65.0 29/16 0500065

67.0 25/8 0500067

68.0 211/16 0500068

70.0 23/4 0500070

73.0 27/8 0500073

ALFRA – HSS-Bi-Metal Hole Saws

Combi toothing 4/6 tpi

Ø from 14.0 to 210 mm available

B/106

B

Prod.-No. 0501002 A6-SDS

Prod.-No. 0501005 A2-SDS

ALFRA – HSS-Bi-Metal Hole Saws

Saw-Ø mm Inch Prod.-No.

74.0 211/12 0500074

76.0 3 050007679.0 31/

8 0500079

83.0 31/4 0500083

86.0 33/8 0500086

89.0 31/2 0500089

92.0 35/8 0500092

95.0 33/4 0500095

98.0 37/8 0500098

102.0 4 0500102 105.0 41/

8 0500105

108.0 41/4 0500108

111.0 43/8 0500111

114.0 41/2 0500114

121.0 43/4 0500121

127.0 5 0500127

140.0 51/2 0500140

152.0 6 0500152

FromØ160.0mmonlysuitableforwoodandwoodsubstitutes. 160.0 65/

16 0500160

168.0 610/16 0500168

177.0 7 0500177 210.0 85/

16 0500210

Arborswithguidingdrillbit

Saw-Ø mm Saw-Ø inch Type Shank-Ø Prod-No.

14-30 9/16-13/

16 A6-SS9.5 hexagon 0501001

14-30 9/16-13/

16 A6-SDS SDS 0501002

32-152 11/4-6 A2-SS 9.5 hexagon 0501003

32-152 11/4-6 A2-SDS SDS 0501005

32-210 11/4-85/

16 A3-SS 11.11hexagon 0501006

32-210 11/4-85/

16 A5-SS 16.0hexagon 0501008

Accessories:

RimcountersinkforØ68mm(withTCT-teeth) 0501013

Extensionshaft300mmx9.5mm 0501010forA6-SS+A2-SS,A3-SS

SpareCenterDrillHSSØ6,35mmx80mm 0502001forA6-SS+A6-SDS+A2-SS+A2-SDS+A3-SS+A5-SS

EjectorSpring 0502004

Important: Disable impact drill when using SDS-shanks!

Prod.-No. 0502001

Prod.-No. 0502004

Prod.-No. 0501001 A6-SS

9.5 mm3/

8“

Prod.-No. 0501003 A2-SS

Prod.-No. 0501006 A3-SS

Prod.-No. 0501013

Prod.-No. 0501013 with bi-metal hole saw Ø 68 mm + A2-SS

Prod.-No. 0501010

Diverse applications

9.5 mm3/

8“

11.11 mm7/

16“

11.11 mm7/

16“

9.5 mm3/

8“

B/107

BALFRA – HSS-Bi-Metal Hole Saws - Sets

ThefollowingHSS-Bi-MetalHoleSawSetsenlargeourrange.Thesesetswereespeciallycompiledforelectricians,mechanics,plumbersandforge-neral,universalapplications.Thesesetsimprovethepresentation.Storageinsolidtoolcases.

Hole Saw Set Standard Prod.-No. 0503006Contents:Ø16mm(5/

8“)

Ø19mm(3/4“)

Ø22mm(7/8“)

Ø29mm(11/8“)

Ø35mm(13/8“)

Ø44mm(13/4“)

Ø52mm(21/16“)

Ø57mm(21/4“)

Ø67mm(25/8“)

ArborA6-SS,ArborA2-SS,SpareTwistDrill

Hole Saw Set Professional Prod.-No. 0503007

Contents:Ø16mm(5/

8“)

Ø19mm(3/4“)

Ø22mm(7/8“)

Ø25mm(1”)Ø29mm(11/

8“)

Ø32mm(11/4“)

Ø35mm(13/8“)

Ø38mm(11/2“)

Ø44mm(13/4“)

Ø51mm(2”)Ø64mm(21/

2“)

Ø76mm(3”)ArborA6-SS,ArborA2-SS,SpareTwistDrill

Hole Saw Set Electro Prod.-No. 0503008

Contents:Ø22mm(7/

8“)

Ø29mm(11/8“)

Ø35mm(13/8“)

Ø44mm(13/4“)

Ø51mm(2”)Ø64mm(21/

2“)

Ø68mm(211/16“)


Hole Saw Set Sanitary Prod.-No. 0503009

Contents:Ø16mm(5/

8“)

Ø19mm(3/4“)

Ø24mm(15/16“)

Ø29mm(11/8“)

Ø38mm(11/2“)

Ø44mm(13/4“)

Ø57mm(21/4“)

Ø67mm(25/8“)


Sales Display on request!

Prod.-No. 0503006

Prod.-No. 0503007

Prod.-No. 0503008

Prod.-No. 0503009

B/108

B

2/109B/109

B

Stainless steel

TCT-Hole Saws – FRP type

TCT-Hole Saws – short-/long type

Plastic

Poroton stone

TCT-Hole Saws in use

B/110

BTCT-Hole Saws in use

TCT-Hole Saws – MBS type

Checker plate (VA)

Sanitary pipes – type SML

Sanitary pipes – type SML

MBS ProUse on Rotabest Magnetic Drilling Machinewith MT3 – Arbor Prod.-No.: 0734003

B/111

Bstainless

steel

ALFRA TCT-Hole Saws – Short TypeMade in Germany by ALFRA

TheapplicationareaofTCTHoleSawsdiffersfromHSS-Bi-MetalHoleSaws.WithALFRATCTHoleSaws,suitabletoeconomicallyprocessstainlesssteelupto2mm(1/16”),unalloyedsteelsupto4mm(3/16”),plastics,PVC,aluminium,zinc,gypsumplasterboardsandlightweightbuildingboards,aswellasasbestos.Donotuseautomaticfeed,whenworkingwithpillardrillingmachines.Fortheuseonportable-andpillardrillingmachines.Donotuseautomaticfeed,whenworkingwithpillardrillingmachines.

Features: ■ Highconcentricrunningexactnessthroughsolidconstruction.■ CAD-optimizedcuttingangleswithspeciallygroundsectionensureshigh

cuttingcapacityandlongtoollife.■ Quickremovalofdrilledcorethroughejectorspringforallholesawsup

to150mm(529/32”)Ø.■ Carbidetippingenablesrepeatedre-grinding.■ ALFRAholesawsarerepairable.Intheeventofatoothbreaking,itcan

easilybereplacedandresharpened.■ Exchangeablecenterpin.■ UseofMTtoolholdersfromØ31mm(17/32”).■ Foruseonhanddrillingmachines(recommendeduptomax.Ø40mm;

19/16”)orstationarymachines.

Tips: ■Atthickermaterials:cut2-3mmpercuttingprocess,removechips

afterwards.■ Whencuttingmetals,ahigh-gradecuttingoilshouldbeused.

Exception:Donotusecuttingoilwhenusingcastiron,useparrafininsteadofoilwhencuttingaluminium.

■Keep in mind: Always wear safety goggles.

Another special technical feature:FromØ15.2mm(3/16“)to30.0mm(11/8“),theholesawismadeofonepiece.FromØ31.0mm(13/16”)weusespeciallyhardenedtoolholderstocom-pensateforthetorsionalpowerincaseofheavyoperation,whichavoidsearlyshearingoffofthetoolholdershank.

In terms of construction not comparable with any other make.

Basic body

Clamping screw

Ejector Spring

Tapered center drill with pre- and post-cutterCentering without running off(center punching not necessary)

Ø 15.2 - 50.0 mm ^= 10.0 mm shank(Ø 9/

16“ - 2“ ^= 3/

8“ shank)

Ø 51.0 - 150.0 mm ^= 13.0 mm shank(Ø 2“ - 6“ ^= 1/

2“ shank)

4 mm (3/16

“)

12 mm (7/16

“)

B/112

BALFRA TCT-Hole Saws – Short TypeMade in Germany by ALFRA

HSS-Spare Drillwith tapered center tip

fromØ15.2-150.0Ø6x50mm 0602650fromØ101.0-150.0Ø8x50mm 0602850(olddesign)

MT Arbors

MT-2(Ø31.0-100.0mm) 0734002MT-3(Ø31.0-150,0mm) 0734003

SDS Arbor

SDSarborshank 060sds6(forusewithØ31-100mm)

Spare EjectorfromØ15.2-150.0Ø6mm 0602006

Coolant ALFRA

ALFRA BIO 2000FormildsteelSt37,405ml 21010

ALFRA 3000Forstainlesssteel,520ml 21030

Prod.-No. 0600001

Prod. No. 21010/21030

Set Metric Prod.-No.SetMetric 0600001

Contents:1eachofØ16/20/25/32/40mm2AllenKeys

Ø Ø No. of Prod.-No. mm Inch teeth mm Inch

Ø15.2 0600152Ø16.0 5/8”’ 4 0600160 0630160Ø17.0 4 0600170Ø18.0 11/16” 4 0600180 0630180Ø18.6 4 0600186Ø19.0 3/4” 4 0600190 0630190Ø20.0 5 0600200Ø20.4 5 0600204Ø21.0 13/16” 5 0600210 0630210Ø22.0 5 0600220Ø22.5 5 0600225Ø23.0 7/8” 5 0600230 0630230Ø24.0 15/16” 5 0600240 0630240Ø25.0 5 0600250Ø26.0 1” 5 0600260 0630260Ø27.0 1-1/16” 5 0600270 0630270Ø28.0 5 0600280Ø28.3 5 0600283Ø29.0 1-1/8” 5 0600290 0630290Ø30.0 1-3/16” 5 0600300 0630300Ø31.0 6 0600310Ø32.0 1-1/4” 6 0600320 0630320Ø33.0 6 0600330Ø34.0 1-5/16” 6 0600340 0630340Ø35.0 1-3/8” 6 0600350 0630350Ø36.0 6 0600360Ø37.0 1-7/16” 7 0600370 0630370Ø38.0 7 0600380Ø39.0 1-1/2” 7 0600390 0630390Ø40.0 1-9/16” 7 0600400 0630400Ø41.0 8 0600410Ø42.0 1-5/8” 8 0600420 0630420Ø43.0 1-11/16” 8 0600430 0630430Ø44.0 8 0600440Ø45.0 1-3/4” 8 0600450 0630450Ø46.0 8 0600460Ø47.0 1-13/16” 9 0600470 0630470Ø48.0 1-7/8” 9 0600480 0630480Ø49.0 9 0600490Ø50.0 1-15/16” 9 0600500 0630500Ø51.0 2” 9 0600510 0630510Ø52.0 10 0600520Ø53.0 2-1/16” 10 0600530 0630530Ø54.0 2-1/8” 10 0600540 0630540Ø55.0 10 0600550Ø56.0 2-3/16” 10 0600560 0630560Ø57.0 2-1/4” 10 0600570 0630570Ø58.0 10 0600580Ø59.0 2-5/16” 10 0600590 0630590Ø60.0 2-3/8” 10 0600600 0630630Ø61.0 11 0600610Ø62.0 2-7/16” 11 0600620 0630620Ø63.0 11 0600630Ø64.0 2-1/2” 11 0600640 0630640Ø65.0 11 0600650Ø66.0 2-9/16” 12 0600660 0630660Ø67.0 2-5/8” 12 0600670 0630670Ø68.0 12 0600680Ø69.0 2-11/16” 12 0600690 0630690Ø70.0 2-3/4” 12 0600700 0630700Ø71.0 12 0600710Ø72.0 2-13/16” 13 0600720 0630720Ø73.0 2-7/8” 13 0600730 0630730Ø74.0 2-15/16” 13 0600740 0630740Ø75.0 13 0600750Ø76.0 3” 13 0600760 0630760


Ø77.0 13 0600770Ø78.0 3-1/16” 14 0600780 0630780Ø79.0 3-1/8” 14 0600790 0630790Ø80.0 14 0600800Ø81.0 3-3/16” 14 0600810 0630810Ø82.0 14 0600820Ø83.0 3-1/4” 14 0600830 0630830Ø84.0 3-5/16” 15 0600840 0630840Ø85.0 15 0600850Ø86.0 3-3/8” 15 0600860 0630860Ø87.0 3-7/16” 15 0600870 0630870Ø88.0 15 0600880Ø89.0 3-1/2” 16 0600890 0630890Ø90.0 3-9/16” 16 0600900 0630900Ø91.0 16 0600910Ø92.0 3-5/8” 16 0600920 0630920Ø93.0 16 0600930Ø94.0 3-11/16” 16 0600940 0630940Ø95.0 3-3/4” 17 0600950 0630950Ø96.0 17 0600960Ø97.0 3-13/16” 17 0600970 0630970Ø98.0 3-7/8” 17 0600980 0630980Ø99.0 17 0600990Ø100.0 3-15/16” 17 0601000 0631000Ø105.0 4” 18 0601050 0631050Ø110.0 18 0601100Ø115.0 4-1/2” 20 0601150 0631150Ø120.0 20 0601200Ø125.0 20 0601250Ø130.0 5” 20 0601300 0631300Ø135.0 24 0601350Ø140.0 5-1/2” 24 0601400 0631400Ø145.0 24 0601450Ø150.0 24 0601500

B/113

Bstainless

steel

ALFRA TCT-Hole Saws – Long TypeMade in Germany by ALFRA

Features: ■ Especiallydevelopedfortheuseonpipes,vaultedmaterials,forunallo-

yedandalloyedsteels,nonferrousmetals,plasticsaswellasglassfibrereinforcedplastic.

■ Formaterialthicknessupto4mm(3/16”),2mm(1/16”)stainlesssteel.■ Foruseonhanddrillingmachines,recommendeduptomax.Ø40mm

(19/16”)orstationarymachines.

Tips: ■ Startdrillingoperationwithlightpressure,whendrillingpipes.

Avoidpendulummotions.■Keepinmind:Alwayswearsafetygoggles.

Special tools for special applications on request!


Special tool for Macrolon

Special tool for insulant

Ø 20.0 - 50.0 mm ^= 10.0 mm shank(Ø 25/

32“ - 1 15/

16“ ^= 3/

8“ shank)

Ø 51.0 - 100.0 mm ^= 13.0 mm shank(Ø 2“ - 4“ ^= 1/

2“ shank)

4 mm (3/16

“)

Ø 20.0 - 59.0 mm ^= 35.0 mm(Ø 25/

32“ - 2 5/

16“ ^= 1 3/

8“)

Ø 60.0 - 100.0 mm ^= 60.0 mm(Ø 2 3/

8“ - 4“ ^= 2 3/

8“)

B/114

BALFRA TCT-Hole Saws – Long TypeMade in Germany by ALFRA


vonØ20.0-59.0Ø6x80mm 0702680vonØ60.0-100.0Ø8x100mm 0702800

MT Arbors

MT-2(abØ31,0) 0734002MT-3(abØ31,0) 0734003

SDS Arbor

SDSarborshank 060sds6(forusewithØ31-59mm)

ALFRA BIO 2000

isafullysyntheticcuttingoil,develo-pedforhigh-qualitycutting,threadinganddrillingofmetalsofanydegreeofhardness,ferrousmetal,steelalloys,stainlesssteel,copper,aluminiumandtheiralloys.ALFRA BIO 2000 is free of hydrocarbon, sulphur and chlorine.

Aerosolcan405ml 21010

ALFRA 3000

Universalmetalworkingoilfreeofchlorine.High-performancedrilling,broachingandcuttingfluid,petroleum-based,formoderatelydifficultanddifficulttocutsteels.Withahighproportionofactiveingredientstoensureoptimumcuttingperformanceandsignificantlyreducedtoolwear.Itmeetsoccupationalhealthandsafetyrequirements.We recommend to use ALFRA 3000 especially for the drilling and threading of high-alloy steel and chrome nickel steel.

Aerosolcan520ml 21030

Highly recommendet accessories – coolant and lubricant!


Ø20.0 5 0700200Ø20.4Ø21.0 13/16" 5 0700210 0710210Ø22.0 5 0700220Ø22.5Ø23.0 7/8" 5 0700230 0710230Ø24.0 15/16" 6 0700240 0710240Ø25.0 6 0700250Ø26.0 1" 6 0700260 0710260Ø27.0 1-1/16" 6 0700270 0710270Ø28.0 6 0700280Ø28.3Ø29.0 1-1/8" 6 0700290 0710290Ø30.0 1-3/16" 6 0700300 0710300Ø31.0 8 0700310Ø32.0 1-1/4" 8 0700320 0710320Ø33.0 8 0700330Ø34.0 1-5/16" 8 0700340 0710340Ø35.0 1-3/8" 8 0700350 0710350Ø36.0 8 0700360Ø37.0 1-7/16" 8 0700370 0710370Ø38.0 8 0700380Ø39.0 1-1/2" 8 0700390 0710390Ø40.0 1-9/16" 10 0700400 0710400Ø41.0 10 0700410Ø42.0 1-5/8" 10 0700420 0710420Ø43.0 1-11/16" 10 0700430 0710430Ø44.0 10 0700440Ø45.0 1-3/4" 10 0700450 0710450Ø46.0 10 0700460Ø47.01-13/16" 10 0700470 0710470Ø48.0 1-7/8" 10 0700480 0710480Ø49.0 10 0700490Ø50.0 1-15/16" 12 0700500 0710500Ø51.0 2" 12 0700510 0710510Ø52.0 12 0700520Ø53.0 2-1/16" 12 0700530 0710530Ø54.0 2-1/8" 12 0700540 0710540


Ø55.0 12 0700550Ø56.0 2-3/16" 12 0700560 0710560Ø57.0 2-1/4" 12 0700570 0710570Ø58.0 12 0700580Ø59.0 2-5/16" 12 0700590 0710590Ø60.0 2-3/8" 14 0700600 0710600Ø61.0 14 0700610Ø62.0 2-7/16" 14 0700620 0710620Ø63.0 14 0700630Ø64.0 2-1/2" 14 0700640 0710640Ø65.0 14 0700650Ø66.0 2-9/16" 14 0700660 0710660Ø67.0 2-5/8" 16 0700670 0710670Ø68.0 16 0700680Ø69.0 2-11/16" 16 0700690 0710690Ø70.0 2-3/4" 16 0700700 0710700Ø71.0 16 0700710Ø72.0 2-13/16" 16 0700720 0710720Ø73.0 2-7/8" 16 0700730 0710730Ø74.0 2-15/16" 16 0700740 0710740Ø75.0 16 0700750Ø76.0 3" 18 0700760 0710760Ø77.0 18 0700770Ø78.0 3-1/16" 18 0700780 0710780Ø79.0 3-1/8" 18 0700790 0710790Ø80.0 18 0700800Ø81.0 3-3/16" 18 0700810 0710810Ø82.0 18 0700820Ø83.0 3-1/4" 18 0700830 0710830Ø84.0 3-5/16" 20 0700840 0710840Ø85.0 20 0700850Ø86.0 3-3/8" 20 0700860 0710860Ø87.0 3-7/16" 20 0700870 0710870Ø88.0 20 0700880Ø89.0 3-1/2" 20 0700890 0710890Ø90.0 3-9/16" 20 0700900 0710900Ø91.0 20 0700910Ø92.0 3-5/8" 20 0700920 0710920


Ø93.0 20 0700930Ø94.0 3-11/16" 22 0700940 0710940Ø95.0 3-3/4" 22 0700950 0710950Ø96.0 22 0700960Ø97.0 3-13/16" 22 0700970 0710970Ø98.0 3-7/8" 22 0700980 0710980Ø99.0 22 0700990Ø100.0 3-15/16" 22 0701000 0711000Ø105.0 4" 22 0701050 0711050

B/115

BALFRA TCT-Hole Saws – MBS-LightThe TCT Multirange Hole Saw • Registered Utility Model No. 202 03 232 9

ThisTCTHoleSawisamulti-rangeHoleSawfortheuniversaluseuptoamaterialthicknessofmax.10mm(3/8”)(withoutejectorspring).Throughitssolidconstructionandanenhancedcuttinggeometry(RegisteredUtilityModelNo.202032329),animprovedcuttingbehaviourcombinedwithahighcuttingcapacityandtoollife,isachieved.

Fortheuseonflatsteel,aswellasonpipesandvaultedmaterials.Cut-tingofoverlappingholesispossible.

Foruseonstationaryandhanddrillingmachines(recommendeduptomax.Ø40mm;19/16”).■ PortabledrillingMachines: upto4mm(1/8”)materialthickness■ StationarydrillingMachines:upto10mm(3/8”)materialthickness (formaterialthicknessover6mm

(15/64”),itisnecessaryto settleandemptythechipsseveraltimes).

Incaseofheavyoperation,werecommendMorseTaperToolHolders,whicharesuitablefromØ37mm(17/166”).

Advantage: All MBS-Light type TCT Hole Saws are equipped with an ejector spring. Thecutmaterialisself-ejecting.Thecutmaterialisself-ejecting.

Basic body

Clamping screw

Ejector Spring


MBS – for almost limitless use

Another special technical feature:FromØ37mm(17/16”),speciallyhardenedtoolholdersareusedtocompensateforthetorsionalpowerincaseofheavyoperationwhichavoidsearlyshearingoffofthetoolholdershank.


Cutting geometriesVariable teeth, less Vibration, longer tool life, smoother cutting.

Ø 18.0 - 36.0 mm = 10.0 mm shank(Ø 11/

16“ - 1 3/

8“ = 3/

8“ shank)

Ø 37.0 - 100.0 mm = 13.0 mm shank(Ø 1 7/

16“ - 3 15/

16“ = 1/

2“ shank)

Recommendation:Use exchangeable Morse Taper arbor MT2 or MT3 from Ø 37.0 mm (1 7/16”) for stability reasons.

10 mm (3/8“)

16 mm (5/8“)

Chip spacebetweenworkpieceand tool

Center drill

Clampingscrew

Chip guideline TCT-teeth

stainlesssteel

B/116

BALFRA TCT-Hole Saws – MBS-LightThe TCT Multirange Hole Saw • Registered Utility Model No. 202 03 232 9

Drilling structured sheet metals

Drilling rectangular tubes

Drilling flat steels

Drilling tubes



MT Arbors

MT-2(fromØ37.0mm) 0734002MT-3(fromØ37.0mm) 0734003

Weldon adaptor

fromØ18.0-100.0mm 060WD(inc.ejectorpinProd.No.1950500)

Spare EjectorFor tapered center drill

fromØ18.0-100.0mmØ6mm 0732006fromØ61.0-100.0mmØ8mm 0732008


Ø18.0 11/16” 6 0730018 0731018Ø18.6Ø19.0 3/4” 6 0730019 0731019Ø20.0 6 0730020Ø20.4Ø21.0 13/16” 6 0730021 0731021Ø22.0 6 0730022Ø22.5Ø23.0 7/8” 6 0730023 0731023Ø24.0 15/16” 6 0730024 0731024Ø25.0 6 0730025Ø26.0 1” 6 0730026 0731026Ø27.0 1-1/16” 6 0730027 0731027Ø28.0 6 0730028Ø28.3Ø29.0 1-1/8” 6 0730029 0731029Ø30.0 1-3/16” 6 0730030 0731030Ø31.0 6 0730031Ø32.0 1-1/4” 6 0730032 0731032Ø33.0 6 0730033Ø34.0 1-5/16” 6 0730034 0731034Ø35.0 1-3/8” 6 0730035 0731035Ø36.0 6 0730036

From Ø 37.0 mm (1 7/16”) we recommend the use of MT arborsØ37.0 1-7/16” 6 0730037 0731037Ø38.0 6 0730038Ø39.0 1-1/2” 6 0730039 0731039Ø40.0 1-9/16” 6 0730040 0731040Ø41.0 6 0730041Ø42.0 1-5/8” 6 0730042 0731042Ø43.0 1-11/16” 6 0730043 0731043Ø44.0 6 0730044Ø45.0 1-3/4” 6 0730045 0731045Ø46.0 6 0730046Ø47.0 1-13/16” 6 0730047 0731047Ø48.0 1-7/8” 6 0730048 0731048Ø49.0 6 0730049Ø50.0 1-15/16” 6 0730050 0731050Ø51.0 2” 6 0730051 0731051Ø52.0 6 0730052Ø53.0 2-1/16” 6 0730053 0731053Ø54.0 2-1/8” 6 0730054 0731054Ø55.0 6 0730055Ø56.0 2-3/16” 6 0730056 0731056Ø57.0 2-1/4” 6 0730057 0731057Ø58.0 6 0730058Ø59.0 2-5/16” 6 0730059 0731059Ø60.0 2-3/8” 8 0730060 0731060Ø61.0 8 0730061Ø62.0 2-7/16” 8 0730062 0731062Ø63.0 8 0730063Ø64.0 2-1/2” 8 0730064 0731064Ø65.0 8 0730065Ø66.0 2-9/16” 8 0730066 0731066Ø67.0 2-5/8” 8 0730067 0731067Ø68.0 8 0730068Ø69.0 2-11/16” 8 0730069 0731069Ø70.0 2-3/4” 8 0730070 0731070Ø71.0 10 0730071Ø72.0 2-13/16” 10 0730072 0731072Ø73.0 2-7/8” 10 0730073 0731073Ø74.0 2-15/16” 10 0730074 0731074Ø75.0 10 0730075Ø76.0 3” 10 0730076 0731076Ø77.0 12 0730077


Ø78.0 3-1/16” 12 0730078 0731078Ø79.0 3-1/8” 12 0730079 0731079Ø80.0 12 0730080Ø81.0 3-3/16” 12 0730081 0731081Ø82.0 12 0730082Ø83.0 3-1/4” 12 0730083 0731083Ø84.0 3-5/16” 12 0730084 0731084Ø85.0 12 0730085Ø86.0 3-3/8” 14 0730086 0731086Ø87.0 3-7/16” 14 0730087 0731087Ø88.0 14 0730088Ø89.0 3-1/2” 14 0730089 0731089Ø90.0 3-9/16” 14 0730090 0731090Ø91.0 14 0730091Ø92.0 3-5/8” 14 0730092 0731092Ø93.0 14 0730093Ø94.0 3-11/16” 14 0730094 0731094Ø95.0 3-3/4” 14 0730095 0731095Ø96.0 14 0730096Ø97.0 3-13/16” 14 0730097 0731097Ø98.0 3-7/8” 14 0730098 0731098Ø99.0 14 0730099Ø100.0 3-15/16” 14 0730100 0731100Ø105.0 4” 14 0730105 0731105

B/117

BALFRA TCT-Hole Saws – MBS-ProThe TCT Multi-Range Hole Saw • Made in Germany by ALFRA

MBS-MultirangeHoleSawsforuniversaluse.Max.cuttingdepth20mm(25/32”)

Suitableforflatmaterialsbutalsoforpipesandcurvedsurfaces.Cuttingofoverlappingholesispossible.CADoptimizedprecisiontoolswithhighcuttingperformanceanddurability.

Foruseonstationaryandportabledrillingmachines(recommendeduptomax.Ø40mm;19/16”)■ PortabledrillingMachines: upto6mm(15/64”)materialthickness■ StationarydrillingMachines:upto20mm(25/32”)materialthickness atcuttingdepthsfrom6mm(15/64”) werecommendclearingthechips.

MBSholesawscanberesharpened,anditispossibletoreplacebrokenoutteethdependingontheconditionoftheholesaw.

Advantages: All Alfra TCT Hole Saws MBS-Pro type are equipped with an ejector spring. Thecutmaterialisself-ejecting.Thecutmaterialisself-ejecting.

Ø 18.0 - 100.0 mm = 13.0 mm shankØ 11/

16“ - 3 15/

16“ = 33/

64 “ shank

Recommendation:Use exchangeable Morse Taper arbor MT2, MT3 or 13 mm straight shank from Ø 31 mm (1 7/32”) for stability reasons.

Clamping screw

Basic body

Ejector Spring


20 mm (25/32

“)

MBS – for almost limitless usee.g., on Rotabest Magnetic Drilling Machine (with MT2 or MT3 – arbors)

and Weldon adaptor Prod.-No. 060WD on Machines with Weldon Shank.

30 mm (1 3/16

“)

Another special technical feature:FromØ31mm(17/32”),weusespeciallyhardenedtoolholderstocompensateforthetorsionalpowerincaseofheavyoperation,whichavoidsearlyshearingoffofthetoolholdershank.


Cutting geometriesVariable teeth, less Vibration, longer tool life, smoother cutting.

B/118

BALFRA TCT-Hole Saws – MBS-ProThe TCT Multi-Range Hole Saw • Made in Germany by ALFRA

Drilling structured sheet metals

Drilling tubes

Drilling flat steels

Free-hand drilling up to Ø 30 mm



MT Arbors

MT-2(Ø31.0-100.0mm) 0734002MT-3(Ø31.0-100.0mm) 0734003

Weldon adaptor

fromØ18.0-100.0mm 060WD(incl.ejectorpinProd.No.1950500)

Spare EjectorFor tapered center drill

fromØ15.2-100.0Ø6mm 0762006suitableforsparedrillØ6mm


Ø18.0 11/16" 6 0760018 0761018Ø18.6Ø19.0 3/4" 6 0760019 0761019Ø20.0 6 0760020Ø20.4Ø21.0 13/16" 6 0760021 0761021Ø22.0 6 0760022Ø22.5Ø23.0 7/8" 6 0760023 0761023Ø24.0 15/16" 6 0760024 0761024Ø25.0 6 0760025Ø26.0 1" 6 0760026 0761026Ø27.0 1-1/16" 6 0760027 0761027Ø28.0 6 0760028Ø28.3Ø29.0 1-1/8" 6 0760029 0761029Ø30.0 1-3/16" 6 0760030 0761030

As from Ø 31.0 mm (1 7/32“) we recommend the use of MT arborsØ31.0 6 0760031Ø32.0 1-1/4" 6 0760032 0761032Ø33.0 6 0760033Ø34.0 1-5/16" 6 0760034 0761034Ø35.0 1-3/8" 6 0760035 0761035Ø36.0 6 0760036Ø37.0 1-7/16" 6 0760037 0761037Ø38.0 6 0760038Ø39.0 1-1/2" 6 0760039 0761039Ø40.0 1-9/16" 6 0760040 0761040Ø41.0 6 0760041Ø42.0 1-5/8" 6 0760042 0761042Ø43.0 1-11/16" 6 0760043 0761043Ø44.0 6 0760044Ø45.0 1-3/4" 6 0760045 0761045Ø46.0 6 0760046Ø47.01-13/16" 6 0760047 0761047Ø48.0 1-7/8" 6 0760048 0761048Ø49.0 6 0760049Ø50.0 1-15/16" 6 0760050 0761050Ø51.0 2" 6 0760051 0761051Ø52.0 6 0760052Ø53.0 2-1/16" 6 0760053 0761053Ø54.0 2-1/8" 6 0760054 0761054Ø55.0 6 0760055Ø56.0 2-3/16" 6 0760056 0761056Ø57.0 2-1/4" 6 0760057 0761057Ø58.0 6 0760058Ø59.0 2-5/16" 6 0760059 0761059Ø60.0 2-3/8" 8 0760060 0761060Ø61.0 8 0760061Ø62.0 2-7/16" 8 0760062 0761062Ø63.0 8 0760063Ø64.0 2-1/2" 8 0760064 0761064Ø65.0 8 0760065Ø66.0 2-9/16" 8 0760066 0761066Ø67.0 2-5/8" 8 0760067 0761067Ø68.0 8 0760068Ø69.0 2-11/16" 8 0760069 0761069Ø70.0 2-3/4" 8 0760070 0761070Ø71.0 10 0760071Ø72.0 2-13/16" 10 0760072 0761072Ø73.0 2-7/8" 10 0760076 0761073Ø74.0 2-15/16" 10 0760074 0761074Ø75.0 10 0760075


For drilling stainless steel from Ø 76.0 mm we recommend using Rotabest AL cutters (Prod.-No. 200205....)Ø76.0 3" 10 0760076 0761076Ø77.0 12 0760077Ø78.0 3-1/16" 12 0760078 0761078Ø79.0 3-1/8" 12 0760079 0761079Ø80.0 12 0760080Ø81.0 3-3/16" 12 0760081 0761081Ø82.0 12 0760082Ø83.0 3-1/4" 12 0760083 0761083Ø84.0 3-5/16" 12 0760084 0761084Ø85.0 12 0760085Ø86.0 3-3/8" 14 0760086 0761086Ø87.0 3-7/16" 14 0760087 0761087Ø88.0 14 0760088Ø89.0 3-1/2" 14 0760089 0761089Ø90.0 3-9/16" 14 0760090 0761090Ø91.0 14 0760091Ø92.0 3-5/8" 14 0760092 0761092Ø93.0 14 0760093Ø94.0 3-11/16" 14 0760094 0761094Ø95.0 3-3/4" 14 0760095 0761095Ø96.0 14 0760096Ø97.0 3-13/16" 14 0760097 0761097Ø98.0 3-7/8" 14 0760098 0761098Ø99.0 14 0760099Ø100.0 3-15/16" 14 0760100 0761100Ø105.0 4" 14 0760105 0761105

B/119

BALFRA TCT-Hole Saws – FRP typeThe TCT Multi-Range Hole Saw • Made in Germany by ALFRA

Cutting depth 60 mm (2 3/8”)■ Speciallydesignedforwood,plain,laminatedandcoatedchipboard,

plywood,paper-baselaminate,PVC,glassfibrereinforcedplastic,gasconcrete,Ytongstone,plasterboard,hollowgaugedbrick/stones.

■ Noblockingduetooptimalcuttinggeometry.■ Simpledrillcoreremovalbasedonnewchipspacedesign.■ Intheeventofatoothbreaking,itcaneasilybereplacedandre-

sharpened.■ Onlyusewhenrotating,switchoffhammeraction.■ Idealforelectricians,plumbersandheatingengineers,carpentersand

cabinetmakers,stairconstructionandkitchenfurniturefitters.

ArborsSW 12 or SDS

Perfect assembly of sockets in e.g. wood, gypsum plaster board,...

Rim Countersink

Basic body

Center Drill

Prod.-No. 0740068060 – FRP Ø 68 mm with tool holder and rim countersink

Please indicate material and thickness!

ALFRA TCT-Hole Saws – FRP Multi-Tooth

with arbor shank■ Cuttingdepth35.0/60.0forsandwich-compositematerial,woodand

chipboardcoatedwithinsulationandsheetmetal(alsostainless),e.g.,countersandrefrigerators.

up to Ø 50.0 mm: 10.0 mm shankfrom Ø 51.0 mm: 13.0 mm shank

35.0 mm to Ø 59.060.0 mm from Ø 60.0

B/120

BALFRA TCT-Hole Saws – FRP typeThe TCT Multi-Range Hole Saw • Made in Germany by ALFRA

Prod.-No. 0743000002

Ø TCT-Hole Saws FRP Prod.-No.mm inch singledrillbit,cuttingdepth60mm

25.0 Sanitaryandheatingpipes 074002506025.0 Sanitaryandheatingpipes 074002506035.0 13/8“ Sanitaryandheatingpipes 0740035060 Cavitywallbranchbox,halogenreflectorlamp40.0 Sanitarydrainpipes 074004006045.0 Waterandheatingpipes 074004506050.0 withinsulation 074005006055.0 RecessedlightsØ55mm 074005506058.0 RecessedlightsØ58mm 074005806060.0 ᅠ RecessedlightsØ60mm 074006006063.0 SwitchboxØ60mm 074006306065.0 CavitywallboxØ65mm 074006506068.0 CavitywallboxØ68mm 074006806070.0 CavitywallbranchboxesØ70mm 074007006074.0 CavitywallbranchboxØ74mm 074007406080.0 Junctionboxes,cableglandcovers, 0740080060 RecessedlightsØ80mm85.0 RecessedlightsØ85mm 074008506090.0 ᅠ RecessedlightsØ90mm 0740090060105.0 Dischargeairpipes 0740105060

RimcountersinkforØ68mm 0741068000

ToolHolderwrenchsize12 0742000001

ToolHolderSDS 0742000002

SparecenterdrillHSS7.2mm 0742000003

FRP Hole Saw Set ElectricianContent: 07430000011eachofØ35/68/741ToolHolderwrenchsize121HSSdrill

FRP Hole Saw Set LightingContent: 07430000021eachofØ35/60/68/80/85mm1ToolHolderwrenchsize121HSSdrill

Ø TCT-Hole Saws FRP Multi-tooth Prod.-No. Noseriesproduction.Deliveryonrequest.mm witharbor,cuttingdepth35/60mm.

40.0 Sanitarydrainpipes 075004004040.0 Waterandheatingpipes 075004504050.0 withinsulation 075005004055.0 075005504060.0 075006006063.0 Switchboxes,diameter60mm 075006306065.0 075006506068.0 socketdrill 075006806070.0 075007006074.0 Junctionboxes,diameter70+74mm 075007406075.0 075007506080.0 Junctionboxes 075008006085.0 075008506090.0 075009006095.0 0750095060100.0 0750100060105.0 Dischargeairpipes 0750105060Intermediatesizesandothercuttingdepthsonrequest 0759......

HSS spare drill for FRP Multi-toothØ30.0-59.0mm=8x80 0752880Ø61.0-105.0mm=8x100 0752800

Prod.-No. 0743000001

B/121

BXX SPIRALXgROOvEd,XEACHXStEPXWItHXAXIALXAndXRAdIALXRELIEfXgRIndIngXACCORdIngXtOXItSXdIAMEtER

XX LASER-EtCHEdXSCALEXInXtHEXCHIPXSPACE

XX SPECIALXdRILLXtIPXEnABLESXCEntERIngXAndXdRILLIngXEvEnXtHROugHXtHIn-WALLEdXMAtERIALS

XX BuRR-fREEXdRILLIngXWItHXnOXdEfORMAtIOnXOfXtHEXSHEEt

XX REgRIndABLE

XX AvAILABLEXInXHSSXAndXHSSXWItHXtIAInXCOAtIng

ALFRA-Pr e c i S i o n Multi-SteP DrillS

B/122

BApplication area:Theidealtoolforsheetmetalforming,fortheelectricalindustry,HVACorthecommonengineeringortheswitchboardindustry.

Suitableforallmaterialssuchasnonferrousmetals,stainlesssteelsheets,thermoplasticandthermosettingplastics,aswellasforsteelsheetsuptoamax.materialthicknessof6mm.

WiththeMulti-StepDrills,sheetmetalscanbecentered,drilledandsubse-quentlydeburredinoneworkstep.

■ Abreakofthedrilltipmostlyoccursthroughhighfeedforcesatthestartofthedrillingoperation.Multi-stepdrillswithfixeddrilltipsareworthlessthen.AbrokencenterdrillinanALFRAmulti-stepdrillcanbeeasilyreplaced.Thismorethancompensatesforthehigherprice.

■ Eachstageisequippedwitharadiallyadjustedreliefgrindingcorre-spondingtoitsdiameter.

■ Eachstageisprovidedwithanaxialreliefgrindingandareliefangleonitscuttingedge.

■ Allstepdiametersarelasermarkedonthetool.

Benefits of multi-step drills with keyway and 3 cutting edges:■ Thekeywayallowsthedrilltomakeachippingcutduringdrillingfor

betterchipremoval.■ Thespecialkeywaygeometry,arrangedaroundthedrill,makesforalon-

gercuttingedgecomparedtotheusualstraightgrooveandnoticeablyeasiercutting.

■ Spiralcutchipspacesguaranteeanabsoluterunningsmoothnessandahighcuttingcapacity.

Tip:ThetoollifecanbeconsiderablyprolongedbyusingofALFRACuttingSprayorALFRACoolantStick.

Advantages of TiAlN hard coating:■ Suitableforuseonveryhardmaterials(VA).■ Offersoptimaltoollifewiththesameuseatthehighestcuttingspeeds.■ VeryhighmicrohardnessHV0.05of3200–sothattheblue-blackhard

coatingismorethan20%harderthanconventionalgold-yellowTINcoating.

■ Maximumworkingtemperature:800°C.

Description Shank Ø Prod.-No.AMS 10.0 08080Forgeneralmachineconstruction,drillscircularholesinmetalsupto4mmthick,throughapplicationwithhanddrills,indispensableonthework-site.3chipspaces,spiralgrooved,replaceablecenterdrillSteps Ø 9 - 12 - 15 - 18 - 21 - 24 - 27 - 30 - 33 - 36 mm(Step “40” is for deburring)

AMS – TiAlN coated 10.0 080813chipspaces,spiralgrooved,replaceablecenterdrillTiAlNcoatedSteps Ø 9 - 12 - 15 - 18 - 21 - 24 - 27 - 30 - 33 - 36 mm(Step “40” is for deburring)

AM 1 12.0 08002Steps Ø 25 - 28 - 31 - 34 - 37 - 40 - 43 - 46 - 49 - 52 - 55 - 58 mm

PVD 10.0 08003Fortheelectricalindustry,matchedtoholesforarmouredconduitthreadclearanceholes,savesconsiderabletimewhenproducingboringsforPGSteps Ø PG 7 - PG 9 - PG 11 - PG 13 - PG 16 - PG 21 - 33 mm - PG 29 - 40 mm

Prod.-No. 08080 ■

Multi-Step Drills – HSS DM O5More precise hole diameter through cylindrical steps. Hole deburring through the next step.

Prod.-No. 08081 ■

Prod.-No. 08002 ■6 Prod.-No. 08003 ■6

■Exchangeable center drills6 4 chipspaces

4or6mm

Burrremoval,Countersinking

Boring

B/123

BMulti-Step Drills – HSS DM O5More precise hole diameter through cylindrical steps. Hole deburring through the next step.

Description Shank Ø Prod.-No.

PVD-TiN-coated 10.0 08004

PVK 10.0 08005LikePVD,butforarmouredconduitthreadcore hole PGSteps Ø PG 7 - PG 9 - PG 11 - PG 13 - PG 16 - PG 21

SVB 10.0 08016Pre-drillspecificallyforpunches&diesSteps Ø 8.5 - 11.5 - 12.5 - 16.5 - 21.0

DKS 32 12.0 080823chipspaces,spiralgrooved,replaceablecenterdrillClearance holes Ø 12.5 - 16.5 - 20.5 - 25.5 - 32.5Core holes Ø 10.5 - 14.5 - 18.5 - 23.5 - M12 - M16 - M20 - M25 - M32

DKS 32 TiAlN coated 12.0 080833chipspaces,spiralgrooved,replaceablecenterdrillClearance holes Ø 12.5 - 16.5 - 20.5 - 25.5 - 32.5Core holes Ø 10.5 - 14.5 - 18.5 - 23.5 - M12 - M16 - M20 - M25 - M32

DKS 40 10.0 080843chipspaces,spiralgrooved,replaceablecenterdrill,formetricboringsacc.toEN,Core - and clearance holes M 10 - M 40Steps Ø 10.5 - 12.5 - 14.5 - 16.5 - 18.5 - 20.5 - 25.5 - 32.5 - 38.5 - 40.5

DKS 40 – TiAlN coated 10.0 080853chipspaces,spiralgrooved,replaceablecenterdrillFormetricboringsacc.toEN50262Core - and clearance holes M 10 - M 40Steps Ø 10.5 - 12.5 - 14.5 - 16.5 - 18.5 - 20.5 - 23.5 - 25.5 - 32.5 - 38.5 - 40.5

DKI-VA 10.0 080324chipspaces,replaceablecenterdrillofHSS-Co5steel.Forstainlesssteelto3mmthickCore - and clearance holes M 10 - M 40Steps Ø 10.5 - 12.5 - 14.5 - 16.5 - 18.5 - 20.5 - 23.5 - 25.5 - 32.5 - 38.5 - 40.5

Spare center drill 08007suitableforAMS–PVD–PVK–DKI–DKS

Spare center drill TiAlN 08008suitableforAMS–PVD–PVK–DKI–DKS

Prod.-No. 08004 ■6 Prod.-No. 08005 ■6

Prod.-No. 08016

Prod.-No. 08084 ■

Prod.-No. 08032 ■6

Prod.-No. 08082 ■

Prod.-No. 08007■Replaceable center drill 66 With 4 chip spaces

Pre-drill specificallyfor punches & dies

Prod.-No. 08085 ■

Prod.-No. 08008

Prod.-No. 08083 ■

B/124

BMulti-Step Drills – HSS DM O5More precise hole diameter through cylindrical steps. Hole deburring through the next step.

Prod.-No. 08072

Standard execution with 2 chip spaces, spiral grooved.■ Morepreciseholediameterthroughcylindricalsteps.■ Immediatedeburringthroughthenextstep■ Drillingofsheetmetalsasthinas4mmpossible.■ Usecoolantstick!■ Thekeywayallowsthedrilltomakeachippingcutduringdrillingfor

betterchipremoval.■ Longercuttingedgecomparedtotheusualstraightgrooveandnotice-

ablyeasiercutting.■ Laser-etchedscaleinthechipspacetoindicatetheborediameterachie-

ved.

Description Bore range Shank Ø Length Prod.-No.

AM-12 4-12mmx1mm 6.0 70mm 08070AM-20 4-20mmx2mm 9.0 77mm 08071AM-30 6-30mmx2mm 10.0 98mm 08072

Set in plastic case 08073Contents:1ofeachTypeAM-12/AM-20/AM-30

High-performancecoolantstick 09011

Standard values for the use of ALFRA Multi-step

drills

Thisdrillwasdevelopedtoboreperfectlyroundanddeburredholesinsheetmetalfrom4-6mmthick.Thetransitionformsaradiuswhichser-vestodeburrorbeveltheholeatthesametime.Whileconicalone-lipbitsdrillaslightlytaperedhole,ourALFRAmulti-stepdrillachievesacylindricalhole.Thetoolshaveaxial-radialreliefgrindingsandcanbelightlyregroundonthebreastofthecuttingtooth.

Werecommendtheuseofpillardrillingmachines,however,thesmallAL-FRAMulti-stepdrillscanbeusedonadjustablehanddrillingmachines.Suf-ficientcoolingusingALFRAcoolantstickoraboreemulsionisimperative.

Speed chart rpm

Prod.-No. 08073Type sheetsteel stainlesssteelnon-ferrous plastics St37 sheets metals (soft)AM drill 800 360 1000 1000 countersink 500-180 50-70 800-400 1000-400AM-1 drill 800 360 1000 1000 countersink 200-100 100-50 500-200 600-250PVD+PVK+DKI drill 800 360 1000 1000PVD-VA+SVB countersink 400-200 200-100 800-500 1000-600

Prod.-No. 09011

B/125

BPrecision Conical One-Lip Bits – HSS DM 05With laser-marking

ALFRAPrecisionConicalOne-LipBitsaretheidealtoolsforgeneralsheetmetalworking.FieldsofapplicationsincludeHVAC,electronicindustries,engineeringandpanelbuilding.

Tobeusedonnon-ferrousmetals,stainlesssteels,thermo-andduroplasticplastics,aswellasonallcommonsheetsteelsuptoamaterialthicknessofmax.4mm.WithALFRAConicalOne-LipBits,youcancenter,spotdrillandboreupinoneworkstep.

Iftreatedcarefully,canberegroundmanytimes.

ThetoollifecanconsiderablybeprolongedbyusingALFRACuttingOilorCoolantStick.

Packing: separately in plastic box with operation manual.

Size Range Shank-Ø Prod.-No.1 3.0-14.0 6.0 090012 6.0-20.0 8.0 090023 16.0-30.5 10.0 090034 26.0-40.0 12.0 090045 35.0-50.0 12.0 090056 46.0-60.0 13.0 090067L 4.0-30.5 10.0 090078* 6.0-22.5 8.0 09008Set1 Size.1+2+3+Stift 09009

Coolantstick,separately 09011

*Special Antenna-Bit■ Conicalone-lipbitwithcylindricalendsectiontodrillholesfor carantennas.■ Burr-free,nodeformation,nocountersinking,dimensionalaccuracy■ Size6,0-22,5mm.

Precision Conical One-Lip Bit Set Prod.-No.Tinbox 09009

Contents:1xSize11xSize21xSize3

Prod.-No. 09001 Prod.-No. 09002

Prod.-No. 09004 Prod.-No. 09005

Prod.-No. 09006

Prod.-No. 09003

Prod.-No. 09007 Prod.-No. 09008*

Prod.-No. 09009

B/126

B

B/127

BOriginal Astroflex® – Sabre Saw Blades

For Rockwell, Makita, Black & Decker, Bosch, Holz-Her, Atlas Copco, Rems, Roller, Milwaukee, Hilti and others.

■ Anewrangeofsabresawbladeswithimprovedcuttingperformanceandprecisiongroundteeth.Cobaltalloyedteeth.■TheHSS-Bi-Metalbladeisalmostunbreakableandsuitableforallmaterialsandapplications.■Thissabresawbladestandsforhighest qualityanddurability.

For Metal

Application Range Material thickness Steel- Length Width Thickness Teeth Milford AlfraMetal processing in mm Quality inch Prod.-No. Prod.-No.

Metalprocessing;softmetalscopper-,aluminium-,brass-cables,wiresandpipes HSS-Bi 100mm 16mm 0.9mm 14 88161 30255

Metalprocessing;softmetalscopper-,aluminium-,brass-cables,wiresandpipes HSS-Bi 100mm 16mm 0.9mm 18 88162 30256

Allkindofmetals,stainlesssteelsteelpipes,castiron,alloys,etc. HSS-Bi 150mm 16mm 0.9mm 14 88177 30259


Allkindofmetals,stainlesssteel 10/14steelpipes,castiron,alloys,etc. HSS-Bi 150mm 16mm 0.9mm Combo 88216 30262




Allkindofmetals,stainlesssteel 10/14steelpipes,castiron,alloys,etc. HSS-Bi 200mm 16mm 0.9mm Combo 88217 30266

SpecialSabreSawBladeflexibletype 10/14forcastiron-andsteelpipes HSS-Bi 290mm 16mm 0.9mm Combo 88218 30272

For Wood

SpecialSabreSawBladeforWood withnails,especiallyfortherefurbishing HSS-Bi 150mm 19mm 0.9mm 6 88142 30385

SpecialSabreSawBladeforWood 4/6-curvedcuts- HSS-Bi 150mm 19mm 0.9mm Combo 88143 30386

SpecialSabreSawBladeforWood -Refurbishing- HSS-Bi 210mm 19mm 0.9mm 6 88144 30387

SpecialSabreSawBladeforWood -Refurbishing- HSS-Bi 290mm 19mm 0.9mm 6 88145 30388

> 3 mm

> 1 mm

> 3 mm

> 1 mm

3-6 mm

> 6 mm

> 3 mm

> 1,15 mm

3-6 mm

3-10 mm

B/128

BOriginal Astroflex® – HSS-Bi-Metal Sabre Saw Blades

For Rems- and Roller Sabre Sawing Machines

For pipes

Application range Steel quality Length Width Thickness Teeth Blade Alfra per inch No. Prod.- No.

PipesuptoØ2“ HSS-Bi-Metal 140mm 25mm 1.6mm 8 88140-8 30089PipesuptoØ4“ HSS-Bi-Metal 200mm 25mm 1.6mm 8 88200-8 30092

for free-hand and flush cutting

Forfree-handandflushcutting HSS-Bi-Metal 150mm 25mm 1.1mm 14 30105 HSS-Bi-Metal 200mm 25mm 1.1mm 14 30103e.g.refurbishing,onwallsandoverhead HSS-Bi-Metal 300mm 25mm 1.1mm 14 30104

Packagingunit:5pieces

MadeofHSSBi-Metalforburr-anddistortion-freecuttingofthinsheetmetalsandplates,aswellasforpipesinventilationandairconditionconstructions.Precisecrossing,highestendurance.

Application range Length Thickness Width Teeth Prod.-No. mm mm mm inch

Forsheetmetalsasfrom1,1mmthickness,plasticupto3mm,woodupto5mm 96 0,6 12,5 14 31014 96 0.6 12.5 18 31015Forsheetmetals0.7-1.1mmthickness 96 0.6 12.5 24 31016Forsheetmetalsupto0.7mmthickness 96 0.6 12.5 32 31017Forsheetmetalsasfrom1.1mmthickness,plasticupto3mm,woodupto5mm 97 0,6 12,5 14 31018 97 0.6 12.5 18 31019Forsheetmetals0.7-1.1mmthickness 97 0.6 12.5 24 31020Forsheetmetalsupto0.7mmthickness 97 0.6 12.5 32 31021

Attention:donotuseanypressure,feedonlywithdeadweightofmachine.

ALFRA-Special-Sabre-SawBladescanbeusedproblem-freeonthesema-chines.MadeofHSS-Bi-Metal,heattreatedtothepoint.

■ MadeofhighalloyHSS-Bi-Metal■ Heattreatedtothepoint■ Highestheathardnessandwearresistance■ Toothingincrossedversion

ALFRA – Jigsaw BladesSuitable for pneumatic saws as e. g. SIG and Flex-sheet Metal-Tiger Saws

}

}

Prod.-No. 31014 - 31017 Prod.-No. 31018 - 31021

B/129

BMetal Hacksaw Blades

For Hacksawing machines■Youcanusetheefficiencyofthewholemachinewiththesemachine

sawblades.■ Forsawingsolidmaterial,pipesandprofilesofallstrengths.■ Also for high-strength steels■ Withparabolictoothagainstearlybreak■ Sharp-edgedandwear-resistant,withfinecarbiderepartitioninmicro

structure■ Straightenedbymasterhand■ Foralltypesofmachines

Dimension mm available toothing tpt Prod.-No.

300x25x1.5 8 10 14 33010350x30x1.5 6 8 10 14 33011350x30x2.0 4 6 8 10 33012400x30x1.5 6 8 10 14 18 33013400x30x2.0 4 6 8 10 33014450x30x2.0 4 6 8 10 33015450x35x2.0 4 6 8 10 33016450x40x2.0K 4 6 8 10 33017500x40x2.0 4 6 8 10 33018575x50x2.5K 3 4 6 33019650x55x2.5K 3 4 6 33020700x55x2.5K 3 4 6 33021

Prod.-No. 33...K = Kasto with displaced side holesOther dimensions and toothings on request.Length measured from hole center to center.Packaging unit: 10 pieces

Machine Saw Blades – HSS DM O5

TypesTypeF Flexible,economicalcarbonsteelblade.TypeM Universallyusable,partiallyheattreatedHSSblade.TypeR Full-hardenedbladeforprecise,guidedcuts,madefrom HSSsteelwithhighCobaltcontent.TypeBiH Blade with hardened tooth tips, therefore semi-flexible withhighhardnessmadefromHSSsteelwithhighCobalt

contentTypeBi-Metal “Unbreakable”–madefromHSSBi-metal,forflexible,

robustapplication.

Type No. of teeth/Inch Prod.-No.

TypF 18Z WavySet 3300F18TypF 24Z WavySet 3300F24TypF 32Z WavySet 3300F32TypM 18Z RakerSet 3300M18TypM 24Z RakerSet 3300M24TypM 32Z WavySet 3300M32TypR 18Z RakerSet 3300R18TypR 24Z RakerSet 3300R24TypR 32Z WavySet 3300R32TypBiH 18Z RakerSet 3300BiH18TypBiH 24Z RakerSet 3300BiH24TypBiH 32Z WavySet 3300BiH32TypBi-Metall 18Z RakerSet 3300BiM18TypBi-Metall 24Z RakerSet 3300BiM24HSS-Bi-Metal 32Z WavySet 3300BiM32

■Customerbrandexecutionincolour,imprintandpackagingfrom15,000piecespossible

■Packagingunit:100pieces

B/130

B

Excellent for use withRotabest®-Metal Core Drilling Machines, because they are water soluble.

Coolant – Cutting, Drilling, Broaching Oils

Prod.-No. 21002

Prod.-No. 21010

Prod.-No. 21030

RIXOL-2000Coolant concentrate ■ Universaluseforsawinganddrillingofsteel,stainlesssteel,castiron,

nonferrousmetalandaluminiumalloys.■ Wateremulssive,containsmineraloil,rot-proof,stablesolution.■ Providesgoodrustprotectionandlubrication. Causesnoirritationoftheskin.■ Nosmokedevelopmentandnocoagulation.■ FactorIforhandrefranctometer.■ Mixture:Cutters8-10%,Circularsaws5-12%,Bandsaws6-20%

Prod.-No.10kgplasticcontainer 21002

ALFRA BIO 2000High performance cutting oil, biologically degradable

■ ALFRABIO2000isanentirelysyntheticcuttingoil,developedforthemetalworkingindustryforcoredrilling,turning,drilling,milling,ream-ing,countersink,rubbing,tapping

■ Ideallyqualifiedforallsteelandsteelalloys,chrome-nickelsteel,cop-per,aluminiumalloys.

■ ALFRABIO2000doesn’tcontainanyhydrocarbonandischlorinefree.■ Withspecialhighpressureandantiwearadditives.■ Withcorrosionandrustprotection.■ Increasestoollifeupto200%andshortensoperatingtime,reduces

thenumberofrejects.■ BiologicallydegradableaccordingtotheEUstandard:CECL-33-T-94

Prod.-No.Can405ml 210105kgplasticcontainer 2101260kgdrum 21021

ALFRA 3000High performance Cutting Oil Spray

■ Forthemostdifficultworkingprocedureslikecoredrilling,drilling,turn-ing,tapping,reaming,countersink,rubbing

■ Withspecialhighpressureandantiwearadditives.■ Forusageofhighalloyedstainlesssteel,chrome-nickelsteelandits

alloys,titaniumandmanganesecarbonsteel.■ Qualifiedfornon-ferrous-andlightmetals.■ Increasestoollifeupto200%,shortensoperatingtime.Reducesthe

numberofrejects.■ Sticksonsurfaces,thereforeit’squalifiedfor“overheadworks”on

wallsandceilings.

Prod.-No.Can520ml 210305kgplasticcontainer 2103160kgdrum 21032

B/131

Documents

Metal Cutting Saw RS 200 + RS 230