MAY 1997 - Edmolift · j 2 HISTORY EDMOLIFT AB Härnösand – Katrineholm, Sweden The company was founded by Torbjörn Edmo in Härnösand 1964. The company name of Torbjörn Edmo

123456789101112131415161718192021222324

P

English handbook

History

Choice of lift table

Single scissor lift tables, Lorry loaders

Vertical double scissor and triple scissor lift tables

Horizontal double scissor lift tables

Low profile lift tables

Power pack for single, double and triple scissor tables

Remote power pack for low profile tables

Pallet lifters

Lifting trolleys

Electrical system — Control units

Hydraulic valves for lift tables and pallet lifters

Lifting trolleys — Battery maintenance, Electric and Hydraulic circuitOil recommendations — Assembly instructions TZD 201

Electrical and hydraulic circuit for single, double, triple scissorand low profile tables

Electrical and hydraulic circuit for lift tables with single anddouble acting tilt

Electrical and hydraulic circuit for pallet lifters with and without tilt

Installation — Rated current

Installation floor mounted or pit installed — Pit drawingUnloading and loading — Installation of pallet lifters

Safety regulations — Oil recommendations

Maintenance — Fault tracing

Transport damage — Warranty — Conditions of deliveryExport markets

Accessories, Lorry loaders

Test report, Delivery note, Additional documentation – inside back cover

Manufacturing:

EDMOLIFT ABJägaregatan 11871 42 HÄRNÖSANDSWEDEN

ORGANISATION NO.556241-1222EU VAT no. SE556241122201Innehar F-skattesedel

E-post: [email protected]

j

MAY 1997

j

2

HISTORY

EDMOLIFT ABHärnösand – Katrineholm, Sweden

The company was founded by Torbjörn Edmoin Härnösand 1964. The company name ofTorbjörn Edmo AB, being changed to EdmoliftAB in 1990.

Historically, the company can be described asinnovative, having played an important part inhydraulic products other than those manufactu-red under their own name, e.g. Zepro lorry taillifts. From the late ’60s to the late ’80sEdmolift’s product range was marketed underthe name of ”Translyft”.

From January 1st 1990, Edmolift Sales AB inKatrineholm has been responsible for marketingand sales of the products and built up an excel-lent network of distributors throughout Europe.

The demands and needs of tomorrow will bedifferent from today and will therefore raise thedemands of efficiency, flexibility and awarenessof the world around for all companies.

In order to meet these demands Edmolift AB,Härnösand and Edmolift Sales AB, Katrineholmhave on May 1st 1997, been merged. Amongothers, the reason for the merger is:

to bring the manufacturing facility closerto the end user to enable the customerto have the benefit of 30 years experi-ence within the industry.

to further increase production, primarilythrough the ever-expanding export mar-ket.

BUSINESS CONCEPTTo manufacture and supply lift tables, lift trol-leys, pallet lifters and other closely relatedmaterials handling equipment to provide ergo-nomically sound and efficient products to meetthe needs of our customers. Through productdevelopment and adaption, in close liaison withour customers – the users – we endeavour tooffer products at appropriate technologicallevels, consistent design quality and competiti-ve pricing.

PRODUCTS AND MARKETSWherever possible, common components areused i.e. the same power pack or platform on anumber of models. A wide range of specialaccessories and options are available to meetspecific and individual customer requirements.Edmolift stock spares for pre-1990 products,marketed under the Translyft name. Sales inSweden are through a distributor network.Other countries have exclusive distributors wholook after the particular need of users withintheir own territories.

Production Härnösand

Edmolift Härnösand

Edmolift Katrineholm

5/97

j

23

CHOICEOFLIFT TABLE

Max load=evenlydistributed!

FUNCTION ? Lifting height – Lift stroke (travel) • Lowest heightPlatform length • Platform widthPower pack integral or remote • Electrical requirements

CAPACITY ? Max load • Weight distribution • Shock loadsRevolving and/or side surges • Concentrated loadLoad evenly spread • Driving over with trucks or lorriesLoad moving on a conveyor

INTENSITY ? Speed • Frequency of use • Number of cycles per yearIncorporated in automatic system

ACCURACY ? Limit switch upper-lower • Is immediate stop neededShould the table remain in exactly the same position for along time

ENVIRONMENT ? Outside installation • Pit installation • Damp • ColdDust • Heat • Chemicals • Demands from authorities

SAFETY ? Risk of explosions • Slip protection • Risk of tippingControlling – emergency controls – Risk of trapping

ERGONOMICS ? Are there any accessories which can improve workingconditions, e.g. tilting platform with a retaining edge, or aturntable?

1000 kgs 1000 kgs

Importantquestionswhen choosingmodel andspecificationof lift table!

9/96

Before deciding which model and design of lift table is required consider all theconditions! Lift tables are used for a wide variety of functions and in many diffe-rent situations. It is impossible to manufacture a standard model for every appli-cation. It is therefore very important to consider the specification at the begin-ning, so the lift table can be correctly equipped for its purpose.

Using the TL 2000 as the base model, the following example shows thetype specifications and capacities for Edmolift lift tables:

Single scissor TL 2000 = Max load 2000 kgs evenlydistributed

Double vertical scissor TLD 2000 = Max load 2000 kgswith double lifting height evenly distributed

Double horizontal scissor TLH 2000 = Max load 2000 kgswith double length of platform evenly distributed

Table to be used intensively HD-equipment for the lift table

Edmolift tables comply with all European safety regulations e.g. AFS 1985:13 inSweden, BS 5323 in Great Britain and VBG 14 in Germany with TÜV approvaland in the future CEN.

The mark on Edmolft's products confirms they are manufactured in accordan-ce with applicable CE directives.

Standard lift tables are equipped to function long and reliably with ”normal” use.Tables meant for intensive use with heavy loads, fast speed, extreme environ-ment and perhaps continuous working shifts, will probably need ”HD”-equipment.As standard our lift tables are supplied with electrics to safety standard IP54. Inaccordance with safety regulations, lift tables for use in outside areas must beequipped with anti-slip platform surfaces (e.g. tearplate). Tilting platforms mustinclude a fixed method of retaining the load.

j

4

The sound level of the Edmo-power pack complieswith the regulations of max 70 dB (A). If a speciallymade unit exceeds 70 dB (A), it is stated in themanual that accompanies the table.

If the table has special equipment, e.g.”HD”-equipped, se additional document enclosedwith the lift table. (Last page in the handbook).

SINGLE SCISSORLIFT TABLES

Single scissors are our most widely used industrial plat-forms. The table can be installed both outdoors and in-doors, installed in a pit or operated from the factory floor.The Lorry Loaders are specially equipped with reinforcedplatforms in tearplate and with mechanical stops in thebaseframe.

NB! The capacity of the tables is meant for evenlydistributed loads.

When ordering spare parts, please state the manufacturing number and the model of the table.

Spare parts for

Power pack see page 8

Electrical system see page 12

2/97

Safety frame/m 93.42289

Installation kit 93.82019

8

1

7

5

8

6

4

1

2

3

1 2 3 4 5 6 7 8

MODEL POWER PACK CYLINDER SEAL SET HOSE SAFETY BEARING SET WHEELS SAFETYVALVE SWITCH

TR 500 H 1-0,8 1-40-175 54.33306 – 50.82111 52.43859 64.68010 65.42207 41.65220TR 1001 H 1-0,8 2-40-175 54.33306 – 50.82111 52.43859 64.68012 61.42285 41.65220

TL 1000, B, XB H 4-3 1-80-175 54.33036 51.82090 50.48100 52.43755 64.68012 61.42584 41.65220TL 1000SS H 1-1,2 1-80-175 54.33946 51.82090 50.44246 52.44247 64.68012 61.44169 –TL 2000 H 6-4 2-80-175 54.33036 51.82090 50.48100 52.43755 64.68015 61.43841 41.65220

TM 1500, B H 6-4 2-80-175 54.33036 51.82090 50.48060 52.43755 64.68015 61.43841 41.65220TM 3000 H 8-11 2-100-240 54.50070 51.55130 50.48060 52.42249 64.68075 61.43841 41.65220TM 6000 H 11-11 4-90-240 54.33727 51.55081 50.48105 52.42249 64.68075 61.44015 41.65220

TA 1000 H 6-4 2-70-210 54.50020 51.55071 50.48060 52.42249 64.68015 61.43841 41.65220TA 4000 H 11-11 2-100-320 54.50080 51.55130 50.48060 52.42249 64.68075 61.44015 41.65220TA 10000 H 15-50 4-100-320 54.50080 51.55130 50.48080 52.42249 64.68030 61.43850 41.65220

TS 2000, B H 8-11 2-100-240 54.50070 51.55130 50.48060 52.42249 64.68075 61.43841 41.65220TS 4000, B H 11-11 2-100-320 54.50080 51.55130 50.48060 52.42249 64.68075 61.44015 41.65220

TT 3000 H 11-11 2-100-320 54.50080 51.55130 50.48060 52.42249 64.68075 61.43841 41.65220TT 6000 H 15-20 3-100-450 54.50090 51.55130 50.48050 52.42249 64.68035 61.42564 41.65220TT 10000 H 15-50 4-100-450 54.50090 51.55130 50.48050 52.42249 64.68040 61.43850 41.65220

TP 3000 H 11-11 2-100-450 54.50090 51.55130 50.48050 52.42249 64.68020 61.41032 41.65220TP 6000 H 15-20 3-100-600 54.50100 51.55130 50.48050 52.82031 64.68035 61.42564 41.65220

TV 10000 H 15-50 4-100-600 54.50100 51.55130 50.48090 52.82031 64.68040 61.43850 41.65220

LORRYLOADERSTTK 2, B, XB H 11-11 2-100-320 54.50080 51.55130 50.48060 52.42249 64.68075 61.42508 41.65220TTK 4, B, XB H 11-20 2-100-450 54.50090 51.55130 50.48050 52.42249 64.68035 61.42564 41.65220TPK 5, B, XB H 11-20 2-100-600 54.50100 51.55130 50.48050 52.82031 64.68035 61.42564 41.65220

j

45

The sound level of the Edmo-power pack complieswith the regulations of max 70 dB (A). If a speciallymade unit exceeds 70 dB (A), it is stated in themanual that accompanies the table.

If the table has special equipment, e.g.”HD”-equipped, see additional document enclosedwith the lift table. (Last page in the handbook).

VERTICAL DOUBLESCISSOR AND TRIPLE SCISSORLIFT TABLES

Vertical double scissors allow greater lift heights withoutincreasing the platform size.

Installation: It is essential that these models be securelyfixed to ground or floor with expanderbolts or similar.

NB!The capacity of the tables is meant for evenlydistributed loads


Spare parts forPower pack see page 8Electrical system see page 12

Safety frame/m 93.42289Installation kit 93.82019

2

3

5

8

6

1

7

41

1 2 3 4 5 6 7 8

MODEL POWER PACK CYLINDER SEAL SET HOSE SAFETY BEARING SET WHEELS SAFETYVALVE SWIITCH

TRD 200 H 1-0,8 1-40-175 54.33306 – 50.82111 52.43859 – 65.42207 41.65220TRD 500 H 2-0,8 1-55-300 54.50005 51.55405 50.48045 52.43755 64.68045 61.42584 41.65220

TLD 1000 H 4-3 1-70-450 54.32939 51.55071 50.48043 52.43755 64.68047 61.42584 41.65220TLD 2000 H 6-4 2-70-450 54.32939 51.55071 50.48043 52.43755 64.68052 61.43841 41.65220

TMD 1500 H 6-11 1-100-600 54.50100 51.55130 50.48042 52.82027 64.68052 61.43841 41.65220TMD 3000 H 11-20 2-100-600 54.50100 51.55130 50.48042 52.82027 64.68062 61.43841 41.65220

TSD 1500 H 8-11 2-70-970 54.33175 51.55071 50.48095 52.82027 64.68052 61.43841 41.65220

TTD 3000 H 15-30 2-100-1000 54.50130 51.55130 50.48055 52.82027 64.68062 61.43841 41.65220TTD 5000 H 11-30 2-100-1000 54.50131 51.55130 50.48055 52.82027 64.68035 61.42564 41.65220

TPD 4000 H 15-50 2-100-1380 54.50134 51.55130 50.48090 52.82027 64.68020 61.42564 41.65220TXD 4000 H 15-50 2-100-1780 54.50136 51.55130 50.48090 52.82027 64.68035 61.42564 41.65220

TRIPLE SC.TMT 1500 H 8-11 2-70-970 54.33175 51.55071 50.48080 52.43755 2-64.68052 61.43841 41.65220TST 1000 H 6-11 1-90-1170 54.50160 51.55081 50.48080 52.42249 64.68057 61.43841 41.65220

2/97

j

6


If the table has special equipment, e.g.”HD”-equipped,see additional document enclosed with the lift table.(Last page in the handbook).

HORIZONTALDOUBLE SCISSORLIFT TABLES

Horizontal double scissor with two mechani-cally synchronised scissors, that provide stableconstruction. To be used for heavy loads onlong platforms at low lifting heights.

NB!The capacity of the tables ismeant for evenly distributed loads.

The sound level of the Edmo-power pack complies withthe regulations of max 70 dB (A). If a specially made unitexceeds 70 dB (A), it is stated in the manual thataccompanies the table.

Spare parts for



2/97



5

4

6

6

1

7

2

3

8

1

1 2 3 4 5 6 7 8

MODEL POWER PACK CYLINDER SEAL SET HOSE SAFETY BEARING SET WHEELS SAFETYVALVE SWITCH

TLH 2000 H 4-3 2-80-175 54.33036 51.82090 2-50.48060 52.43755 2-64.68012 61.42584 41.65220TLH 4000 H 6-4 4-80-175 54.33036 51.82090 2-50.48060 52.43755 2-64.68015 61.43841 41.65220

TMH 3000 H 6-11 4-80-175 54.33036 51.82090 2-50.48060 52.43755 2-64.68015 61.43841 41.65220TMH 6000 H 8-11 4-100-240 54.50070 51.55130 2-50.48060 52.42249 2-64.68075 61.43841 41.65220TMH 10000 H 11-20 8-90-240 54.33727 51.55081 2-50.48060 52.42249 2-64.68075 61.44015 41.65220

TAH 2000 H 6-4 4-70-210 54.50020 51.55071 2-50.48060 52.42249 2-64.68015 61.43841 41.65220TAH 8000 H 11-20 4-100-320 54.50080 51.55130 2-50.48060 52.42249 2-64.68075 61.44015 41.65220

TSH 4000 H 8-11 4-100-240 54.50070 51.55130 2-50.48060 52.42249 2-64.68075 61.43841 41.65220TSH 8000 H 11-20 4-100-320 54.50080 51.55130 2-50.48060 52.42249 2-64.68030 61.44015 41.65220

TTH 6000 H 11-20 4-100-320 54.50080 51.55130 2-50.48060 52.42249 2-64.68075 61.43841 41.65220TTH 10000 H 11-20 4-100-450 54.50090 51.55130 2-50.48050 52.42249 2-64.68035 61.42564 41.65220

TPH 6000 H 15-20 4-100-450 54.50090 51.55130 2-50.48070 52.42249 2-64.68020 61.41032 41.65220TPH 10000 H 15-20 4-100-600 54.50100 51.55130 2-50.48090 52.82027 2-64.68035 61.42564 41.65220

j

67

LOW PROFILELIFT TABLES

Low profile lift tables have a liftmechanism, which allows a very lowclosed height, that eliminates theneed for pit installation.

Installation: Lift tables with a liftheight exceeding 800 mm, must besecurely fixed to the ground or thefloor with expanderbolts or similar.

NB! The capacity of the tables ismeant for evenly distributed loads.


TCBTCM

TUBTUM

Accessories

Spare parts for



The sound level of the Edmo-power pack complies with theregulaions of max 70 dB (A). If a specially made unit exceeds70 dB (A) it is stated in the manual that accompanies the table.

TCR

If the table has special equipment, see additional documentenclosed with the lift table. (Last page in the handbook).

2/97

9

9

4 4

4

6

8

8

2

3

5



6

2

3

5

8

7

1

1 2 3 4 5 6 7 8 9

MODEL POWER CYLINDER SEAL SET HOSE SAFETY BEARING WEDGED WHEELS/ SAFETYPACK VALVE SET WHEEL BLOCK SWITCH

TCR 500 HC 3-3 2-40-175 54.33306 – 50.44021 52.43859 64.68008 – 65.42207 41.65220

TCB 600 HC 2-0,8 1-55-135 54.33238 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220TCB 600 H HC 2-0,8 1-55-200 54.33216 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220TCB 1000, B HC 3-3 2-55-135 54.33238 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220TCB 1000 H HC 3-3 2-55-200 54.33216 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220

TCM 2000, B HC 3-3 2-70-150 54.32882 51.55071 50.43729 52.43755 64.68090 61.43639 61.42584 41.65220

TUB 600 HC 2-0,8 1-55-135 54.33238 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220TUB 600 H HC 2-0,8 1-55-200 54.33216 51.55405 50.44021 52.43755 64.68080 61.43927 61.42584 41.65220TUB 1000 HC 3-3 2-55-135 54.33238 51.55405 50.44021 52.43755 64.68080 61.42955 61.42584 41.65220TUB 1000 H HC 3-3 2-55-200 54.33216 51.55405 50.44021 52.43755 64.68080 61.42955 61.42584 41.65220

TUM 2000 HC 3-3 2-70-150 54.32882 51.55071 50.43729 52.43755 64.68090 61.43639 61.42584 41.65220

j

8

The sound level of the Edmo-power pack complieswith the regulations of max 70 dB (A). If a speciallymade unit exceeds 70 dB (A), it is stated in the manualthat accompanies the table.The motor is fitted with thermal overload protection.

POWER PACKSfor single, double and triple scissor lift tables


Spare part numberand function

Page 12


Page 13

Fig. A

Fig. A 1-phase

Fig. B

2/97

5 3 2 4 1

2

3 54

1

1

6

6

1 2 3 4 5 6

MODEL ART.NO FIGURE PLATE TANK PUMP MOTOR VALVE CONTROLUNIT

1 2 3 4 5 6

MODEL ART.NO FIGURE PLATE TANK PUMP MOTOR VALVE CONTROL pUNIT

THREE-PHASEUNIT

400V

ONE-PHASEUNIT

230V

H 1-0,8 57.12100 A 20.33498 55.33296 53.40310 40.60350 52.33545 41.65315H 1-1,2 57.12140 A 20.33498 55.33956 53.40310 40.60350 52.33545 41.65315H 2-3 57.12170 A 20.33528 55.33298 53.40315 40.60360 52.33545 41.65315H 3-3 57.12200 A 20.33528 55.33298 53.40320 40.60360 52.33545 41.65315H 4-3 57.12250 A 20.33528 55.33298 53.40325 40.60360 52.33545 41.65315

H 6-4 57.12300 A 20.33528 55.33314 53.40340 40.60370 52.33545 41.65315H 6-11 57.12350 B 20.33548 55.32031 53.40340 40.60370 52.33545 41.65315H 8-11 57.12400 B 20.33548 55.32031 53.40355 40.60370 52.33545 41.65315H 11-11 57.12500 B 20.33058 55.32031 53.40405 40.60380 52.33636 41.65315

H 11-20 57.12520 B 20.33058 55.33760 53.40405 40.60380 52.33636 41.65315H 11-30 57.12530 B 20.33058 55.33770 53.40405 40.60380 52.33636 41.65315H 15-20 57.12550 B 20.33058 55.33760 53.40410 40.60380 52.33636 41.65315H 15-30 57.12560 B 20.33058 55.33770 53.40410 40.60380 52.33636 41.65315

H 15-50 57.10620 20.21408 55.31477 53.40060 40.60060 52.33636 41.65315

HE 1-0,8 57.12800 1-fas 20.33498 55.33296 53.40310 40.60305 52.33545 41.65315 180

HE 2-3 57.12820 1-fas 20.33528 55.33298 53.40315 40.60310 52.33545 41.65315 210HE 3-3 57.12830 1-fas 20.33528 55.33298 53.40320 40.60310 52.33545 41.65315 120

HE 4-3 57.12860 1-fas 20.33528 55.33298 53.40325 40.60315 52.33545 41.65315 160

MAXPRESSURE

j

89


The sound level of the Edmo-power pack complies with theregulations of max 70 dB (A). If a specially made unit exceeds70 dB (A), it is stated in the manual that accompanies the table.The motor is fitted with thermal overload protection.

REMOTE POWER PACKfor low profile tables

Spare part number and function

Page 12


Page 13

2/97

9

24

6

5

3

7

7

1

8

1 2 3 4 5 6 7 8

MODEL ART.NO PLATE TANK PUMP MOTOR VALVE CONNEC- BOX CONTROL pTION UNIT

1 2 3 4 5 6 7 8 9

MODEL ART.NO PLATE TANK PUMP MOTOR VALVE CONNEC- BOX CONTROL CABLETION UNITTHREE-PHASEUNIT FREESTANDING

400V

ONE-PHASEUNIT FREESTANDING

230V

HC 1-0,8 57.12120 20.33498 55.33296 53.40310 40.60350 52.33545 56.80640 29.33121 41-65315 42.44086HC 2-3 57.12180 20.33528 55.33298 53.40315 40.60360 52.33545 56.80640 29.33121 41.65315 42.44086HC 3-3 57.12210 20.33528 55.33298 53.40320 40.60360 52.33545 56.80640 29.33121 41.65315 42.44086HC 4-3 57.12260 20.33528 55.33298 53.40325 40.60360 52.33545 56.80640 29.33121 41.65315 42.44086

HCE 1-0,8 57.13150 20.33498 55.33296 53.40310 40.60305 52.33545 56.80640 29.33121 41.65315 180HCE 2-0,8 57.13160 20.33498 55.33296 53.40315 40.60305 52.33545 56.80640 29.33121 41.65315 120

HCE 2-3 57.13200 20.33528 55.33298 53.40315 40.60310 52.33545 56.80640 29.33121 41.65315 210HCE 3-3 57.13210 20.33528 55.33298 53.40320 40.60310 52.33545 56.80640 29.33121 41.65315 120

MAXPRESSURE

j

10

PALLET LIFTERS

When ordering spare parts, please state the manufacturing number and the model of the pallet lifters.

TSL TSLN TSE

NB! Stated capacity = Centre of the load 600 mm from the column.

Pallet liftercompletefor self-assembly

Column withhydraulic unit for

built-in applications

Assemblyinstructions page 20.

2/97

The sound of the Edmo-power pack complieswith the regulations of max 70 dB (A). If a spe-cially made unit exceeds 70 dB (A), it is statedin the manual that accompanies the table.

9

7

13

11

forTSL, TSE

TSE

TSL, TSE

for TSLNTransport trolley

for TSL and TSLN

TSLN

14

12

23

5

6

1 4

8

19 17

18

23

20 16

10

23

15


Page 12

VE 32

2021


Page 13

VE 12

VE 25

22

19

16


Page 12

16 17 18 19 20 21 22 23

MODEL ART.NO PLATE TANK PUMP MOTOR VALVE VALVE VALVE CONTROLVE 25 VE 32 VE 12 UNITSAFETY!

Motors are fittedwith thermal over-load protection.

H 3-3 57.12200 20.33528 55.33298 53.40320 40.60360 52.33545 – – 41.65315HN 3-3 57.12230 20.33702 55.33298 53.40320 40.60360 52.33545 52.33735 52.33729 41.65345

HE 3-3 57.12830 20.33528 55.33298 53.40320 40.60310 52.33545 – – 41.65315HNE 3-3 57.13250 20.33702 55.33298 53.40320 40.60310 52.33545 52.33735 52.33729 41.65345

3 4 5 6 7 8 9 10 11 12 13 14 15

SEAL SET HOSE SAFETY BLOCK WHEEL TROLLEY CYLINDER SEAL SET HOSE SAFETY CABLE SWITCH COVERVALVE FRAME KIT

51.55420 50.48032 50.43755 65.33751 61.71210 17.32735 – – – 17.33292 42.82172 41.65220 29.3304951.55405 50.48032 50.43755 65.33751 61.71210 17.32735 – – – 17.33292 42.82172 41.65220 29.3304951.55420 50.48032 50.43755 65.33751 61.71210 – – – – 17.33755 – 41.65270 29.33049

51.55420 50.48032 50.43755 65.33751 61.71210 17.32735 54.32638 51.55420 50.48035 17.33292 42.82172 41.65220 29.33049

1 2

MODEL ART.NO CYLINDER

TSL 1000 H 3-3 1-30-905 54.33096TSL 1500 H 3-3 1-55-905 54.32636TSE 1000 H 3-3 1-30-905 54.33096

TSLN 1000 HN 3-3 1-30-905 54.33096

THREE-PHASE UNIT400V

ONE-PHASE UNIT 230V

j

1011

LIFTING TROLLEYS

for improved ergonomics in industry, shops and warehouses.Capacity 200 kgs, 300 kgs, 500 kgs.

Manual: Mechanical crank, foot pump

Electro-hydraulic: Battery/Charger 12V

Rear wheels have rotational/direction locks.

NB!Lifting trolley TZD 201, B must not be movedwhen it is in raised position.

When ordering spare parts, please state the manufacturing number and the model of the lifting trolley.

5 5 66

10 9 8 3

24

BATTERY POWER PACK *Information and maintenance of battery – page 14

1 2 3 4 5 6 7 8 9 10

MODEL FOOT PUMP. CYLINDER SEAL SET HOSE REAR WHEELS PEDAL BLOCKS LOWERING CRANKPOW. PACK PACKAGE WHEELS RUBBER ROD COMPL.

TZ 201 53.33091 1-25-175 54.33003 51.82112 50.44000 61.71450 61.82110 29.82113 65.42207 29.43797

TZ 501 53.33091 1-40-175 54.33001 51.82112 50.44000 61.71450 61.82110 29.82113 65.42207 29.43797TZ 501 B 57.33013 1-40-175 54.33001 51.82112 50.44001 61.71450 61.82110 – 65.42207 29.43797

TZD 201 53.33091 1-40-175 54.33001 51.82112 50.44000 61.71450 61.82110 29.82113 65.42207 29.43797TZD 201 B 57.33013 1-40-175 54.33001 51.82112 50.44001 61.71450 61.82110 – 65.42207 29.43797

TZ 300 V 61.71450 61.82110 65.42207 68.33630

11 12 13 14 15 16 17 18 19 20 21 22

POWER PACK SOLENOID BATTERY MOTOR CHARGER PUMP TANK PUSH RELAY STRAP COUPLING BANJO GROMMETBUTTON SCREW

57.33013 44.82114 49.82392 40.82115 43.66005 53.82254 55.33331 41.82379 41.82380 72.66205 56.82137 56.82255 51.82378

CRANK WITH SCREW BATTERY POWER PACK

17

12

13

14

22

16 15 19

20

*Lowering valveFiller plug

Pressure reliefvalve

21

Pressure relief valveFiller plugLowering valve

7FOOT PUMP

10

1

111 18

2/97

j

ELECTRICAL SYSTEMfor lift tables and pallet lifters

The electric box is specially made by Edmolift. Supplycable for incoming current is 4-core and consists of 3phases (black, blue and brown), 1 earth (green-yellow).

The connection cable is 0,5 m long. Connector and circuitbreaker are not included. The lift tables are delivered asstandard 400V/24V with control current 24V on controlunits and on switches on the safety frame. For speciallymade tables the electrical diagram is enclosed in theelectrical box and handbook.

12

Safety class IP 54

4*

1

2

3

5

When ordering spare parts, please state the manufacturing number and the model of the table.2/97

6

45.32758 with transf.Standard lift tables andpallet lifters.45.43884 without transf.For 500 V and 400 V with-out neutral extra transf.

ELECTRICAL EQUIPMENT ON EARLIER MODELSLifting tables manufactured before August 1996 usually have the trans-former on the printed circuit board and are not replaceable with the newelectrical system. Printed circuit boards without fuse are furnished with2A 230 V fuse on the electrical box. Printed circuit boards with heat fuseare directly replaceable against cards (shown to the left here), if an in-line fuse is fitted. When replacing circuit boards that have a yellow-greenearth cable for new ones the cable should be connected to terminal no10.

45.32758 with transf.Lift tables with singleacting tilt 45°.45.43884 without transf.For 500 V and 400 V with-out neutr. with extra transf.

45.33112 with transformerLift tables and pallet lifters with double acting tilt 90°.45.43885 without transfornerFor 500 V and 400 V without neutral with extratransformer.

* For power over 4 kW 400 V or 2.2 kW 230V contactorart.no 44.65025

ELECTRICAL SYSTEM 1 2 3 4 5 6

MODEL ART.NO TRANS- FUSE PRINTED CONTACTOR BOX CONTROL UNITFORMER CIRCUIT BOARD

TRANSFORMERPRINTED CIRCUIT BOARDS

CONTROL UNITS – lockable and with emergency stop (additional control units can be connected in series, 5-core cable is needed)

1-phase 110VAC, 50VA 45.33949 43.44248 1A 45.44110 44.65125 46.65590 41.653151-phase 230VAC, 50VA 45.33950 43.44250 1A 45.44110 44.65125 46.65590 41.653153-phase 230VAC, 50VA 45.33950 43.44250 1A 45.44110 44.65125 46.65590 41.653153-phase 400VAC, 50VA 45.33950 43.44250 1A 45.44110 44.65125 46.65590 41.653153-phase 500VAC, 50VA 45.33901 43.44255 1A 45.44110 44.65125 46.65590 41.653153-phase 230VAC, 100VA 45.33653 43.65765 6,3A – 44.65125 46.66200 41.653153-phase 400VAC, 100VA 45.33654 43.65770 6,3A – 44.65125 46.66200 41.653153-phase 500VAC, 100VA 45.33658 43.65780 6,3A – 44.65125 46.66200 41.65315All cables to the connect. block 45.33019 – – – – 46.65590 –Table w. Single acting tilt 400V 45.33955 43.44250 1A 45.44170 44.65125 46.65590 41.65335Table w. Double acting tilt 400V 45.33853 43.65770 6,3A 45.44195 44.65125 46.66200 41.65345Pallet lifter std 400VAC, 50VA 45.33950 43.44250 1A 45.44110 44.65125 46.65590 41.65315Pall. lifter w. tilt 400VAC, 100VA 45.33734 43.65770 6,3A 45.44195 44.65125 46.56200 41.65345

Lift. tables, Pallet lift.

Standard

Art.no 45.44110

Single acting tilt

Art.no 45.44170

Double acting tilt

Art.no 45.44195

Time delayfuse 1ADimensions: 5x20 mm

230V/L2

400V/L2Alternativeplacement of fusedepending onvoltage

With extra lockfor automatic With handle

Single actingtilt

Double actingtilt Foot control

Art.no 41.65345 Art.no 41.33790Art.no 41.65315 Art.no 41.65330 Art.no 41.65325 Art.no 41.65335

StopUpDown

StopAutoUpDown

Stop

UpDownTilt downTilt up

StopHandle(3 positions)

UpDown

StopUpTilt(combindewith up-down)

Down DownUp

Stop

j

1213

HYDRAULIC VALVESfor lift tables andpallet lifters

Valve delivered as a spare part does not have theworking pressure adjusted (earth pressure 150 bar).

NB!Lowering speed in accordance with existingstandards max 0,15 m/sec.

When ordering spare parts, please state the manufacturing number and the model of the table.9/96

After 1st August 1996all valves are supplied with 24V = (DC) on the magnetic coil.

SHIFT VALVE VE 92 Double acting tiltSpare part number: Complete valve 52.33120When ordering sparte parts, please advise type of current.

The ”Hirsman contact” is equipped with a rectifier if the coil is to be connected to230 V p 50 Hz (symbol on housing ).

Adjustment ofworking pressure

Hirsman contact

Magnetic coil

Connection 1Tilt - Double acting

Connection 2Tilt + Double acting

Connection 3Lift table Single acting

Lowering speed

SHIFT VALVE VE 32Spare part number: Complete valve 52.33735When ordering spare parts, please advise type of current.

ELECTRICAL REVERSE VALVE VE 12Spare part number: Complete valve 52.33729When ordering spare parts, please advise type of current.

LOWERING VALVE VE 25Spare part number: Complete valve 52.33545For hydraulic flow up to 10 L/min.When ordering spare parts, please advise type of current.

Manometerconnector

Connectionhydraulic cable

Adjustment of workingpressure

YELLOW = VE 25

Magnetic coil

SHIFT VALVE VE 52 Single acting tiltSpare part number: Complete valve 52.33100When ordering spare parts, please advise type of current.

Valve VE 52 is directly interchangeable with the old NA 52 valve provided that youchange the ”Hirsman contact” to one with a rectifier (symbol on housing ).This is valid if it is to be connected to 230 V p 50 Hz.

Connectionhydraulic hose

Magnetic coil Hirsman contact

ConnectionTilt +

ConnectionLift table

Hirsman contact

The working pressure is adjusted at the factoryThe lowering speed has to be finely adjusted on final installation of the lifting table. The loweringspeed adjustment works with pressure compensation and gives a constant lowering speed, irres-pective of size of the load.Important! If the lowering speed is too fast the safety valve in the cylinder may be activated. Thetable will then lower very slowly.

Magnet

LOWERING VALVE VE 26Spare part number: Complete valve 52.33636For hydraulic flowover 10 L/min.Others as VE 25.When ordering spare parts,please advise type of current.

GREEN = VE 26

Lowering speed

Emergency loweringvalve

OptionArt.no 18.82185

Connection

Lowering speed

Hirsman contact

Magnetic coil

Connectionhydraulic hose

Connectioncylinder

j

14

2/97

LIFTING TROLLEYS Battery andcharger, electr. and hydraulic circuitData: Charger: 220V/12V 1,5 A

49.66105 Dryloaded battery with bottle of acid: 12V 30 Ah

49.82392 *Maintenance free battery ”accu-CF”: 12V 24 Ah(No topping-up required)

*Delivered to certain markets.

FILLING WITH BATTERY ACIDNB! WARNING – CORROSIVE ACID!

Battery and acid must be at room temperature when battery is topped up withacid.

Only accumulator acid – thinned pure (approx 38%)

SULPHURIC ACID – with density 1,28 kg/dm3 is to be used as electrolyte.

Remove the battery plugs and fill the cells up to 10 mm over the lead plates.

Leave the battery in room temperature for 20 minutes after that.

The battery is now – after replacing the plugs and washing away of any super-flous – ready for immediate use. Check the electrolyte level after a few days,as it might require adjusting.

BATTERY MAINTENANCECheck that the battery is secure in the battery compartment.

Keep the battery clean and dry. Dirt and oil reduce the battery's efficiency andcan damage the battery.

Always keep terminals and cable clips greased and free from oxides. Poorconnection will cause a loss in voltage.

Check the electrolyte level and when needed refill the battery to 10 mm abovethe lead plates. NB! Unthinned sulphuric acid or ”improved electrolyte” mustnot be used.

Battery to be charged when necessary.

BATTERY CHARGINGThe lead cable for the charger should be connected to a standard220/240V AC.The battery charger is automatic and adjusts the charging current.The charger will automatically cut out when the battery is fully charged.

CONTROLLING HEIGHT ADJUSTMENTBattery trolley: Up with push button on the handle.Footpumped trolley: Up by pumping on the foot pump.Battery and footpumped trolley: Down with spring back handle or foot pedal.

OIL RECOMMENDATION for lifting trolleysHydraulic oil: Shell Tellus 10 or equivalent Oil volume: Foot pump 0,3 liter Battery 0,4 liter

ASSEMBLY INSTRUCTIONSTZD 201, B

FITTING OFLOWERING ROD

FITTING OFHANDLE

WARNING!The battery contains sulphuric acid whichcan cause severe corrosive damage. If youget acid near your eyes, or on skin or clot-hing, immediately rinse with plenty of water.If the acid comes in contact with your eyes,contact a doctor immediately.Charge in spark or flame free area as thehydrogen gas which is formed during char-ging, can be inflammable.Keep away from children.Contents: Sulphuric acid approx 40 %.Discarded batteries must be treated as en-vironmentally dangerours waste and dispos-ed accordingly.

LIFTING TROLLEY FOOT PUMPED ORBATTERY DRAWING NO 33059

12V

CHARGER

Relay

Solenoid

NB!Do not run the trolley with load in raised position.

j

1415

2/97

ELECTRICALAND HYDRAULICCIRCUIT DIAGRAM

for single, double,triple scissor andlow profile lift tables

ELECTRICAL SYSTEM STANDARD 400V ALT 230VARTICLE NUMBER 45.33950

ELECTRICAL SYSTEM 230V 1-PHASEARTICLE NUMBER 45.33950

400 alt 230V

Motor

Contactor

Control unit

Limit up

Limit down

Safety frame

Lowering valve

If there is aHoseburst valve

Thermal overload

400 alt 230V

Motor

Contactor

Control unit

Limit up

Limit down

Safety frame

Lowering valve


Thermal overload

ELECTRIC BOX

HYDRAULIC CIRCUIT

ELECTRIC BOX

HYDRAULIC CIRCUIT

MANOUVERSTOP

MANOUVERSTOP

j

16

9/96

ELECTRICAL SYSTEM 500VWITH TRANSFORMER 100VAARTICLE NUMBER 45.33658



ELECTRICAL SYSTEM WITH ALL CABLES TO THE CONNECTION BLOCKARTICLE NUMBER 45.33019

230V, 400V alt 500V

Motor

Valve down

Hoseburst valve

Valve up

Locking device

Immediate stop

Thermal overload

Control unit 1

Control unit 2

Limit up

Safety frame

Limit down

Locking switch

Round circulation

Double acting tilt

ELECTRIC BOX

HYDRAULIC CIRCUIT

ELECTRIC BOX

EMERGENCY STOP 1

EMERGENCY STOP 2

j

1617

2/97


for lift tables withsingle and doubleacting tilt

ELECTRICAL SYSTEM WITH TILT 90°ARTICLE NUMBER 45.33853

3x400V

Motor

24V DC

Coil F

Coil E

Coil D

Coil C

Coil B

Coil A

Safety frame

Limit up

Limit down

Limit switch tilt down

Limit switch tilt up

K1

Thermal overload

Control unit

ELECTRIC BOX

HYDRAULICCIRCUIT

MANOUVERSTOP

ELECTRICAL SYSTEM WITH TILT 45°ARTICLE NUMBER 45.33955

400 alt 230V

Motor

Contactor

Control unit

Limit up

Limit down

Safety frame

Lowering valve


Thermal overload

Limit sw. tilt up

Limit sw. tilt down

ELECTRIC BOX

HYDRAULIC CIRCUIT

MANOUVERSTOP

j

18

2/97


for pallet lifters withand without tilt

ELECTRICAL SYSTEM WITH TILT ±40° 400VARTICLE NUMBER 45.33734

3x400 V

Motor

24V DC

Coil F

Coil E

Coil D

Coil C

Coil B

Coil A

Safety frame

Limit up

Limit down

Limit left

Limit right

K1

Thermal overload

Control unitELECTRIC BOX

HYDRAULICCIRCUIT

MANOUVERSTOP

ELECTRICAL SYSTEM STANDARD 400V ALT 230VARTICLE NUMBER 45.33950

400 alt 230V

Motor

Contactor

Control unit

Limit up

Limit down

Safety frame

Lowering valve


Thermal overload

ELECTRIC BOX

HYDRAULIC CIRCUIT

MANOUVERSTOP

j

1819

2/97

INSTALLATION

Electrical installation must be done byan authorised person.

The main circuit control unit should have anemergency stop according to EEN 60204.If an extra control is required it must beconnected in series. That installation takesa 5-core cable.

LOCK THE TABLE!During installation, repair andmaintenance under or beside raisedtables, the table must be in lockedposition. See picture no 5 or page 22.

Installation details are for pallet lifters and tables with the powerpacks integral or free standing!

Be careful!Don't lift by thesafety frame. Deform-ation and other dam-ages can occur.(The table will raisebut not lower).

Connect the plug.Supply cable for incomingcurrent is 4-core and consistsof 3-phases(black, blue and brown)1 earth (green-yellow)

Switch on thecurrent. Then thetable will raise automa-tically. If the motorruns but the table doesnot rise, change 2 phases

Lock the table.Unpack the control unit. Remove the tape

blocking the ”UP” button.

NB! It is important that the motor doesnot go the wrong way for too long.

UNPACKINGCheck the packaging for anysigns of damage.Electrical cable forconnection is onone of the shortsidesof the lift table.

j

rR

ADJUSTMENTof safety frame switches

LIMIT SWITCHupper or lower limit switch

EL. CONNECTIONEARTH

Green-Yellow

PHASEBlackBlue

Brown

Cable from lift table to be connec-ted by authorized electrician

Important!If the lowering speed istoo fast the safety valvein the cylinder may beactivated. The tablewill then lower veryslowly.

LOWERING SPEED Max 0,15 m/sec FUSE1A Delay action

Dimensions:5x20 mm.

The electric equip-ment has incoming230 V secured toprotect the circuitboard

230V/L2

400V/L2

Valve information, see page 13.Lowering speed

0,5-

1 m

m

1

3

6

4

5

2

Plug connector and maincircuit breaker are not inclu-ded

RATED CURRENT400V 3-phase standard

Other applications – see marking onhydraulic unit and the above list.

In=Rated current

A=Installation fuse

Low profile lift tablesModel kW In ATCR 500 0,75 2,4 10TCB 600, H 0,75 2,4 10TCB 1000, B, H 0,75 2,4 10TCM 2000, B 0,75 2,4 10TUB 600, H 0,75 2,4 10TUB 1000, H 0,75 2,4 10

Low profile lift tablesTUM 2000 0,75 2,4 10

Pallet liftersTSL 1000, TSE 1000 0,75 2,4 10TSLN 1000 0,75 2,4 10

Single scissor lift tablesTE 500, TR 500 0,37 1,3 10TR 1001 0,37 1,3 10TL 1000 SS 0,37 1,3 10TL 1000, B, XB 0,75 2,4 10TL 2000 1,5 5,0 16TM 1500 B, TM 3000 1,5 5,0 16TM 6000 3,0 9,9 20TA 1000, TS 2000, B 1,5 5,0 16TA 4000, TS 4000, B 3,0 9,9 20TT 3000, TT 6000 3,0 9,9 20

Single scissor lift tablesTT 1000 4,0 11,2 25TP 3000, TP 6000 3,0 9,9 20TA 10000, TV 10000 4,0 11,2 25

Vertical double andtriple scissor lift tablesTRD 200, TRD 500 0,37 1,3 10TLD 1000 0,75 2,4 10TLD 2000 1,5 5,0 16TMD 1500 1,5 5,0 16TMD 3000 3,0 9,9 20TSD 1500 1,5 5,0 16TTD 3000, TTD 5000 3,0 9,9 20TPD 4000 4,0 11,2 25TXD 4000 4,0 11,2 25TMT 1500 1,5 5,0 16

Vertical double andtriple scissor lift tablesTST 1000 1,5 5,0 16

Horiz. double scissor lift tablesTLH 2000 0,75 2,4 10TLH 4000 1,5 5,0 16TMH 3000, TMH 6000 1,5 5,0 16TMH 10000 3,0 9,9 20TAH 2000, TSH 4000 1,5 5,0 16TAH 8000, TSH 8000 3,0 9,9 20TTH 6000, TTH 10000 3,0 9,9 20TPH 6000 3,0 9,9 20TAH 10000, TPH 10000 4,0 11,2 25

Lorry loadersTTK 2, TTK 4 3,0 9,9 20TPK 5 3,0 9,9 20

RATED CURRENTHydraulic unitsfor 400 V 3-phaseModel kW In AH 1 0,37 1,3 A 10 AH 2 0,37 1,3 A 10 AH 2 0,75 2,4 A 10 AH 3 0,75 2,4 A 10 AH 4 0,75 2,4 A 10 AH 6 1,5 5,0 A 16 AH 8 1,5 5,0 A 16 AH 11 3,0 9,9 A 20 AH 15 3,0 9,9 A 20 AH 15 4,0 11,2 A 25 AH 20 4,0 13,2 A 25 A

j

20

INSTALLATIONon the floor or in a pit

Double, triple vertical scissors and low profilelift tables with high lifting heights TCB 1000 H,TUB 600 H and TUB 1000 H, must be securelyfixed to the ground or the floor with expander-bolts or similar.

ASSEMBLY1. The base frames of the tables are as standard not self supporting. It is therefore important that the floor is level and

that the bottom of the pit is level and well drained where necessary.2. Raise and lock the table. See picture page 22. Connect up the permanent cables.3. Place straps through the scissors. Fasten the base frame to the platform or scissor. Ensure the table is in its correct

position. Turn the fixed side of the table in the direction in which the material is to be loaded.4. Electrical installation is to be done by an authorized electrician. Adjust the lowering speed. Test the safety frame on

all sides. Adjust if necessary.5. Recommendation – the control unit should be installed 1,5 m from the working surface, in order to see the movement

of the table clearly.6. After all tests and installation work have been completed, fix the table in the pit with expander bolts or similar. A

recommended method of floor fixing is shown above.

PIT DRAWING

A. The length of the pit = a + 30 mm

B. The width of the pit = b + 30 mm

H. The depth of the pit = the collapsed heightof the table + 5 mm

a. The length of the table

b. The width of the table

c. Drainage holes (if necessary)

d. Tubes for incoming pipes x 60 mm

RECOMMENDATION FOR BOLTING TABLES TOTHE FLOOR

Bolts are not included on delivery of the table.

Alt. 1 Alt. 2

INSTALLATION of pallet lifterand column with power pack

UNLOADINGAND LOADINGUnloading and loading ona raised table should be doneon the fixed side.

The pallet lifter is delivered in threeparts to minimise freight costs.

COLUMN WITH HYDRAULIC UNIT

The column should be fixed to the floor with8 x M16 bolts.Bolt/tension requires 4 x M12/81 Nm.

NB! The risk of trapping should be con-sidered when installing a jig or fixture.Must be bolted to the floor.

YP12-1000

Bolts to be drawn 81 Nm

A complete palletlifterdoes not need to bebolted on the floor.

Wheel side Fixed side

Unloading and loading

Column with hydraulic unit

11/96

Lift tables for outdoorinstallation should if possiblehave a remote power packor be protected.

j

j

2021

9/96

SAFETY REGULATIONS

Edmolift lift tables and pallet lifterscomply with all European safety regulations, e.g.AFS 1985:13 in Sweden, BS 5323 in Great Britainand in Germany with a TÜV approval and futureCEN standard.The mark on Edmolift's products confirms they aremanufactured in accordance with applicable CE directives.

Standard electrics for our lift tables are 400/24 V(415/240 V) and 24 V (240) for the controls andsafety frame switches.

There is a built in safety function in the safetyframe. If the safety frame is touched on its waydown, the table stops immediately. To continuelowering, the table has to be raised a little to beable to lower again.

Edmolift tables are always delivered with a con-trol unit of the ”dead man” type, which meansthat when the up or down button is released thetable will stop immediately. The control unit isequipped with emergency stop and lock.

Employee and employer must see to it thatthe risk of trapping does not occur duringinstallation of lift tables or pallet lifters.

It is the obligation of the employer to see toit that lift tables and pallet lifters are used bycompetent personnel and that checking andmaintenance of lifting equipment is madefrequently.

1. That max load of the lifting equipment is notexceeded. That the load is fixed – must notbe moving.MAX LOAD = LOAD EVENLY DISTRIBUTED!

2. Check the action of the safety frames and thedistance around the equipment to eliminatethe risk of trapping.

3. Warning signs, required by law, must be dis-played.

4. Check for damage due to overloading.

5. Check for oil leakage and possible continuedseepage.

6. Check for oil leakage and grease as necessa-ry.

7. Clean the lift tables and pallet lifters. (Wheeltracks)

8. The main circuit breaker must be accessibleto competent personnel. Lifting equipmentmust not be used by unauthorized personnel.

9. When the load is wheelborne, or there is a lik-elihood that the load may start to roll, theplatform should be fitted with an autorisestop.

10. Lift tables for use in outside areas must beequipped with anti-slip platform surfaces (e.g.tearplate), in accordance with safety regula-tions.

11. Tilting platforms must include a fixed methodof retaining the load.

12. Whenever personnel, other than the operator,are travelling on the platform ensure that thenecessary safety equipment is fitted (e.g.guardrails etc.).

13. Personnel may only ride on the platform ifthat is their intended purpose and this is cle-arly marked on the table.

The stated capacity of the lift tables andpallet lifters is for an evenly distributed load.

Max capacity centre 600 mm from column.NB! Standard lowering speed max 0,15 m/sec. Adjustment see page 13.

1000 kgs 1000 kgs

1000 kgs1000 kgs

OIL RECOMMENDATIONSLIFT TABLES

SUPPLIER TYPE OF OIL

STATOIL Hydol 32, alt Hydraway HV 32

SHELL Tellus 32

BP Bartran 32

MOBIL Mobil DTE 13

CASTROL Hyspin AWH alt Hyspin HVA 32

AT TEMP. BELOW -20° CHydrauloil from Edmo

NB! Differences in quality might occur although all oils meet the same specifica-tions.

WRONG RIGHT

j

22

9/96

NB! The tablemust always belocked during main-tenance and repairs.

Bearings should befree-running andregularly greased.

Central greasingis to be recommendedwhen tables are runcontinuously.

IF THE TABLE DOES NOT LOWER PROPERLY, CHECK FOLLOWING POINTS:

CHECK ACTION

1. Feed voltage and fuses Change the fuse if it is blown.

2. Function of safety frame The switches can be affected. Straighten and adjust. When the safetyequipment is activated and the circuit broken the circuit must be activatedagain by raising the table a little. Adjustment of safety frame, page 19.

3. Adjustment of lowering speed If the speed is too fast the safety valve can shut down. Adjust the lowe-ring speed (reduce the oil flow). See page 13.

4. The table sinks Clean or change the valve.

5. Free standing power pack Check the snap coupling between table and power pack.

IF THE TABLE DOES NOT LIFT PROPERLY, CHECK THE FOLLOWING POINTS:

CHECK ACTION

1. Motor voltage and fuses Change the fuse if it is blown.

2. Direction of rotation of motor If the motor runs in the wrong direction, change two phases. NB! It isimportant that the motor does not run for too long in the wrong direction,the pump can be damaged.

3. The table does not lift max load Adjust the pressure on the valve. Adjust according to the max load to belifted. Test the pressure with a manometer.

4. The table does not lift to max Check the oil level in the tank. Fill up with recommended oil. (Page 21)height and the pump takes in air. NB! The tank should not be filled when the table is raised. If necessary,

bleed the system for air when connecting the hose.

5. Oil leakage Tighten the hose connections. Change cylinder seals or cylinder.

6. Remote power pack Check the snap coupling between table and power pack.

FAULT-TRACINGImportant! All motors have a thermal overload protection against overheating as from May 1996. When fault-tracing, first check that the overload cabling isconnected (purple cable which should be connected to terminal 18 on the P.C.B) Note! When the motor has cooled down it can be started again.

MAINTENANCE GREASINGSTANDARD LIFT TABLESGreasing of bearings in the cylinders must be done at leastevery 1000 cycles.

”HD”-EQUIPPED LIFT TABLESGreasing of bearings in the cylinders must be done at leastevery 1000 cycles. All other places every 2000.

OIL LEAKAGECheck for oil leakage andgrease if necessary.

SAFETY EQUIPMENTCheck the action of the safety framesand the distance around the equipmentto eliminate trapping risk.Adjustment of safety frame, page 19.

OVERLOADINGCheck for damage due to overloading.

CABLES AND HOSESCheck and maintain all cables and hoses.

CLEANINGEnsure wheel tracks are free of obstruction.

j

2223

11/96

TRANSPORT DAMAGE

Carefully check goods andpackaging on receipt!

• Try to check goods on receipt. If there is anydamage the transporter will take the relevant details.

• If damages are discovered when unpacking and assembling,report immediately to the transporter's local office.

• Rembember that the receiver should always report to the transporterif the goods are damaged, irrespective of who is paying freight costs!

WARRANTY AND DELIVERY TERMS

General delivery terms in accordance with NL 92 in Scandinavia.On other markets we refer to the contract of sale in question.

CONDITIONS OF DELIVERY

All products are delivered test run including oil. Electrical equipment is asstandard 400/24V (415/240V) with 24V on the control unit, magnetic coiland safety frame.

Paint: NCS Blue = 3060-R90 B, RAL 5005. Orange = 1070-Y50 R, RAL 2010.Black = 9005-R80 B flat. Edmo-grey = 8005-B20 G, RAL 7024.

EXPORT MARKETSEdmo Lift tables 1996

Norway, Denmark, Finland, Island.Great Britain, Ireland, Germany, France, Holland, Belgium, Spain,Austria, Switzerland, Italy, Greece, Israel, Turkey, Slovakia, Slovenia,Australia, South Korea, Hongkong, Singapore.

jj

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

j

24

11/96

ACCESSORIES

LOAD FLAP TILTING PLATFORMS THE ECO-TILT

LIFT BELLOWSor PVC protective skirt

WIRE MESHSKIRT

TRUCK-HANDLINGCHASSIS

AUTO RISINGSTOP

GUARDRAILwith kick-plate

TURNTABLES CASTORS HD-EQUIPMENTfor tables used intensively

Manual load flap/bridge plate – in sections on request.

Some models of lift tablesrequire enlargement of platform.

Enlargement of platformWidth +100 mm Lenght +100 mm

Auto rising stopThe platform increasedLength +150 mm

Turntable raised1000 kgs – 2000 kgsHeight 55 mm – 61 mm

The collapsed height increasesfrom 240 mm depending onthe model of table.

Turntable platform1000 kgs – 2000 kgsHeight 61 mm

”HD”-equipment means wheels with barings,chromed axles, greased nipples in all linksand drained cylinders.

1100 mm

150 mm

Tilt 0-45° alt. 0-90° Tilt 0-45° high link Tilt 0-30° on TUB 1000Footpumped 0-35°with transport trolley

Art.no 17.32467

DOWNWARD PREVENTION SWITCH

For guides - claw likeArt.no 17.21626Increase the platformlength by 150 mm.

For the base frameMax 1000 kgs

Art.no 17.32158

➞

LIMIT SWITCHupper and lower limit switch

Art.no 17.33680

41.6531541.33790

Standard installation for single and double scissors. Standard installation low profile lift tables.

Art.no 17.43396

Art.no 17.33813Inductive transmitter for

TCR 500

CONTROL UNITS with lock and emergency stop

Art.no 17.3680 Art.no 17.33814

EXTRA SAFETY VALVES

Emergency lowering valveinstalled on VE 25, VE 26. Does notwork in combination with an electricalnon return valve. Art.no 18.82185

ExTCB 1000

Electrical hose• Reduces the down• suspension• Protection for hose• breakageArt.no 17.43348

StandardFoot controls

LORRY LOADERSTTK 2 (TT 3000) TTK 4 (TT 6000) TPK 5 (TP 6000)

• Tabletop in tearplate for antislip protection.Table 2000 kgs – 6 mm tearplateTable 4000 kgs – 5000 kgs – 8 mm tearplate

• 6 mechanical stops in bottom frame.

• Platform reinforced in order to allow a lorry todrive over when table is in collapsed position.

OPTIONSRemote powerpack with hose for installation under shelter.

Auto rising stop (raises when lifting starts). This optionrequires a 150 mm longer platform.

Manual loadflaps (to level and bridge over differences inheight).

Upper limit switch, which stops the liftstroke at a predeter-mined height.

Self supporting base frameInspection flap

41.65330

With extra lockfor automatic

41.65325

Withmulti settings

41.65335

Singleacting tilt

41.65345

Doubleacting tilt

400 mm

30°

90°

The collapsed height increas-es from 135 mm depending onthe model of the table.

Layout and drawings: Erik Niskanen – Edmolift Sales ABDrawings: Katrineholms Reklamdesign and Elmar BlombergPhotographer: Kjell PetterssonComposing and printing: Linderoths Tryckeri, Vingåker 1997

j Lift table

Improvedergonomics

easier, safer andmore efficient

working conditions !

Marketing:

EDMOLIFT SALES ABKöpmangatan 3641 30 KATRINEHOLMSWEDEN

Telefon 0150 - 557 80Int + 46 150 557 80

Telefax 0150 - 551 80Int + 46 150 551 80

E-post: [email protected]

Marketing:

EDMOLIFT UK LTDBlois Meadow Business CentreSteeple BumpsteadNr. Haverhill, Suffolk CB9 7BN

Tel 01440 730640Fax 01440 730004

Documents

MAY 1997 - Edmolift · j 2 HISTORY EDMOLIFT AB Härnösand – Katrineholm, Sweden The company was founded by Torbjörn Edmo in Härnösand 1964. The company name of Torbjörn Edmo