13
Maximum Power Setting Parameters
Embed Size (px)
DESCRIPTION
Maximum Power Setting Parameters
Citation preview
Maximum Power Setting ParametersSlide title 70 pt CAPITALS Slide
subtitle minimum 30 pt
Incorrect Power settings
Abstract
Almost in all circles, “maxtotaloutputpower” and
“maximumtransmissionpower” values are wrongly set for majority of
cells. So due to this, either available power at Antenna port is
underutilized or Resource estimation function of HS scheduler is
calculating wrong value for remaining power for HS.
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area
Q: What does “maxtotaloutpower” = -1 signify?
A: “maxtotaloutpower” is the outputpower of TPA device which is
placed inside the RUW/RRUW. -1 signify that now maxtotaloutputpower
is not defined by the TPA device but is the default RBS
power.
Note: This default RBS power is not always 20 Watt, but it depends
on the type of RUW/RRUW. For eg: “RRU22 21 IV 40” has default power
40 Watt and it doesn’t need any 40 Watt power amplifier license for
this.
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area
Note: “If maximumtransmissionpower” is set more than 2 dB to the
“maxdlpowercapability”, then an alarm:
UtranCell_NbapReconfigurationFailure performance_degraded” comes
for that cell.
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area
Q: Why “maximumtransmissionpower” should not be less than
“maxdlpowercapability” power?
A: “maxdlpowercapability” is the total power which is available at
the System Ref Point (SRP) and “maximumtransmissionpower” is the
power which we set through OSS in RNC to be available for all DL
channels for a cell. So available total power should be equal to
the power used by all downlink channels. If we set
“maximumtransmissionpower” lower than “maxdlpowercapability” then
we are wasting the remaining power which can be available for HS to
improve thpt as well as to reduce power blockings (if any).
Note: All admission control parameters like “pwradm” and
“pwroffset” are relative to min( “maxdlpowercapability”,
maximimumtransmissionpower”)
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area
Q: Why “maximumtransmissionpower” should not be greater than
“maxdlpowercapability”?
A: The reason for this is that Resource estimation procedure in
HSDPA Scheduler takes “maximumtransmissionpower” as the maximum
downlink transmission power for cell to estimate power available
for HS-PDSCHs.
P(HS) = 10^((10* log(Pmax) - hsPowerMargin)/10) - Pnon-HS [W]
So if “maximumtransmissionpower” is set higher than
“maxdlpowercapability”, then Scheduler will overestimate the power
and the above equation will be misleading.
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area
Wherever the change of “maxtotaloutputpower” is required to reduce
power blockings, follow following steps:
Change maxtotaloutputpower
Slide title 44 pt Text and bullet level 1 minimum 24 pt Bullets
level 2-5 minimum 20 pt Characters for Embedded font:
!"#$%&'()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvwxyz{|}~¡¢£¤¥¦§¨©ª«¬®¯°±²³´¶·¸¹º»¼½ÀÁÂÃÄÅÆÇÈËÌÍÎÏÐÑÒÓÔÕÖ×ØÙÚÛÜÝÞßàáâãäåæçèéêëìíîïðñòóôõö÷øùúûüýþÿŒœŠšŸƒˆ˜–—‘’‚“”„†‡•…‰‹›⁄€™−≤≥
ΑΒΓΕΖΗΘΙΚΛΜΝΞΟΠΡΣΤΥΦΧΨαβγδεζηθικλνξορςΣΤΥΦΧΨΩ Do not add objects or
text in the footer area