Materials Sciences and Applications, 2013, 4, 217-280 Published
Online April 2013 in SciRes (http://www.scirp.org/journal/msa/)
TABLE OF CONTENTS
Volume 4 Number 4 April 2013 Minimization of Stock Weight during
Close-Die Forging of a Spindle
H. Ssemakula………………………………………………………………………………………………………………………217
Optimized Distribution and Morphology of Carbon Nanofibers for a
Field Emitter Grown by Nickel and Chromium Cosputtering
N. Shimoi, S.-I.
Tanaka……………………………………………………………………………………………………………225
Removal of Aqueous Lead and Copper Ions by Using Natural
Hydroxyapatite Powder and Sulphide Precipitation in Cyanidation
Process
J. R. Parga, J. L. Valenzuela, V. Vazquez, M. Rodriguez, H.
Moreno……………………………………………………………231
Detection of Corrosion Processes in Metallic Samples of Copper
by CND Control R. Daira, V. Chalvedin, M.
Boulhout………………………………………………………………………………………………238
Synthesis, Characterization and Charge-Discharge Properties of
Layer-Structure Lithium Zinc Borate, LiZnBO3
I. Tsuyumoto, A.
Kihara……………………………………………………………………………………………………………246
Microstructural Development of Fe-20mass%Cr Alloys and Pure
Copper Processed by Equal-Channel Angular Pressing
M. Rifai, R. Haga, H. Miyamoto, H.
Fujiwara……………………………………………………………………………………250
Relationship between Fracture Toughness and Fracture Surface
Fractal Dimension in AISI 4340 Steel L. R. Carney, J. J. Mecholsky
Jr.…………………………………………………………………………………………………258
Determination of Residual Stresses Numerically Obtained in ASTM
AH36 Steel Welded by TIG Process
P. B. Guimarães, P. M. A. Pedrosa, Y. P. Yadava, J. M. A.
Barbosa, A. V. S. Filho, R. A. S. Ferreira…………………………268
Enhancement of Performance of Organic Light Emitting Diodes by
Using Ti- and Mo-Oxide Nano Hybrid Layers
N. N. Dinh, D. N. Chung, T. T. Thao, T. T. C. Thuy, L. H. Chi,
V.-V. Truong…………………………………………………275
The figure on the front cover is from the article published in
Materials Sciences and Applications, 2013, Vol. 4, No. 4, pp.
231-237 by José Refugio Parga, Jesús Leobardo Valenzuela, Víctor
Vazquez, Mario Rodriguez, et al.
Copyright © 2013 SciRes. MSA
Materials Sciences and Applications (MSA)
Journal Information SUBSCRIPTIONS
The Materials Sciences and Applications (Online at Scientific
Research Publishing, www.SciRP.org) is published monthly by
Scientific Research Publishing, Inc., USA.
Subscription rates: Print: $59 per issue. To subscribe, please
contact Journals Subscriptions Department, E-mail:
[email protected]
SERVICES
Advertisements Advertisement Sales Department, E-mail:
[email protected]
Reprints (minimum quantity 100 copies) Reprints Co-ordinator,
Scientific Research Publishing, Inc., USA. E-mail:
[email protected]
COPYRIGHT
Copyright©2013 Scientific Research Publishing, Inc.
All Rights Reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, photocopying,
recording, scanning or otherwise, except as described below,
without the permission in writing of the Publisher.
Copying of articles is not permitted except for personal and
internal use, to the extent permitted by national copyright law, or
under the terms of a license issued by the national Reproduction
Rights Organization.
Requests for permission for other kinds of copying, such as
copying for general distribution, for advertising or promotional
purposes, for creating new collective works or for resale, and
other enquiries should be addressed to the Publisher.
Statements and opinions expressed in the articles and
communications are those of the individual contributors and not the
statements and opinion of Scientific Research Publishing, Inc. We
assumes no responsibility or liability for any damage or injury to
persons or property arising out of the use of any materials,
instructions, methods or ideas contained herein. We expressly
disclaim any implied warranties of merchantability or fitness for a
particular purpose. If expert assistance is required, the services
of a competent professional person should be sought.
PRODUCTION INFORMATION
For manuscripts that have been accepted for publication, please
contact: E-mail: [email protected]
