Marco Full Product Catalog

What’s your angle?

If you want an easy-order, superior seal beveled closure, Anglekut’s got you covered

Why beveled closures? Because a beveled closure’s unique design creates a superior seal between metal roof panels that stops heavy and damaging water from getting in and around the hips and valleys of the roof.

And because Anglekut™ can be made at any angle, it will fit any profile and seal out wind, water, birds, and noise. That makes this product ideal for use in the construction of barns, warehouses, house roofs, and other types of metal roof structures.

Beveled closure designs make a valley or hip application easy to install. And you wind up with a seal as air tight as standard 90-degree closure strips.

Anglekut beveled closures are made from crosslink polyethylene foam, the same material as M-Cell closures, which means they’ll last the lifetime of the

building. Because the product doesn’t bleed, dry out, or dissolve with weather and UV exposure, using 1-1/2” thick foam increases the strength

of the beveled closure and ensures a superior seal of the open area.

The dynamic design of these beveled closures makes it an easy replacement for materials like polyurethane strips or caulking.

Think it will be hard to order a beveled closure product? No way. Just fill out

Anglekut Easy-Order Form on the back of this sheet. You’ll get quick turnaround, too!

If you want a truly superior seal beveled closure, there’s only one that will make the kut. Anglekut.

• Order with one simple form• Quick turnaround• Wire cut to precisely match panel profile/angle

• True fit, fewer gaps• Won’t bleed or dry out

anglekut

Anglekut™ easy order formA

ngle

kut

easy

ord

er

form

Date________________ Customer P.O.#________________ Job # ________________

Complete the following information for each separate closure configuration and beveled angle:1. Panel Name: __________________________________________________________

2. Application : End Wall ______________ Hip ______________ Valley _______________

3. Cut-back Angle: _______________________________________________________

4. Roof Slope (Rise/Run) ________________________ / __________________________

5. A. Number of Panels - Inside: Left Hand__________ Right Hand__________

Outside: Left Hand__________ Right Hand__________

OR B. Quantity in Lineal Ft. - Inside: Left Hand__________ Right Hand__________

Outside: Left Hand__________ Right Hand__________

Key to order entry information:

Panel viewed as plan view for roof or

as elevation view for

wall panel application.

Cut-back angle

Left hand

Right hand

20˚50˚

Left hand cut

Inside

Cut-back angle

Left hand

Right hand

Right hand cut

Outside

It’s fast and easy to order Angle-Kut. Just call 1-800-800-8590 and we’ll walk you through each step in minutes!

Marco Industries Corporate: 9410 E. 54th Street | Tulsa, OK 74145 | 1.800.800.8590 | Fax: 1.918.622.4536

Marco Industries Canada: 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | Fax: 1.306.775.0072

AnglekutTM

To order: 1.800.800.8590 | MarcoIndustries.com | [email protected]

AngleKut represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0910

Precise fit Closure.

Marco Industries’ Closure-Foam™ gives you so

many options when ventilation isn’t an issue for

your project. 400 profiles are already in our line…

and if yours isn’t one of them, we make custom ordering

incredibly easy. So you get precisely the fit and foam you

need for your exact application.

Marco’s M63™ Industrial Adhesive. It’s a big deal,

because applied to all products is a full ¼”

bead once installed so it stays put during

installation and you no longer need to

worry about blow away problems. The

M63™ adhesive is super strong and

specially designed to adhere even

in subfreezing temperatures

and to wet surfaces.

You choose application of the adhesive strip to the flat or the

ribbed side of the closure strip. And with Marco’s glue line

automation, you can depend on a fast turnaround after ordering.

You can also choose dovetails, available with most profiles.

Interlocking dovetails eliminate gaps, ensure a snug end-to-

end fit, and are available with or without the M63™ Industrial

Adhesive. What’s more, all scrap foam parts resulting from

die-cuts are removed leaving you with less job site cleanup.

Closure-Foam™ is economically priced, but you won’t sacrifice

quality. For example, M-Cell thick crosslink polyethylene foam is

heat-treated, creating a unique coating which gives it better UV

resistance, better durability than the industry standard . In fact,

the latest ozone literature confirms that our 1.5 density foam

provides better UV stability than competitive products with a

2.0 density.

• Full ¼" bead once installed of adhesive applied

• Profiles for every application

• 6 different foams• Thickness variety• Better UV resistance

This protective coating forms during the heat-treated process of manufacturing and shields the product from harmful UV rays.

Marco’s Complete Line of High Quality Foam Closures

Closure Foam™

Marco’s Complete Line of High Quality Foam Closures



Property Test Procedure Units LD24Nominal Density - Skin/Skin BS ISO 7214 1998 kg/m³ 24Cell Size – Typical Diameter Internal mm 0.3Compression Stress-Strain BS ISO 7214 1998 10% compression kPa 34 25% compression kPa 53 40% compression kPa 85 50% compression kPa 118Compression Set BS ISO 7214 1998 25% comp., 22hr, 23°C 25 mm cell-cell ½ hr recovery % set 13 24hr recovery % set 550% comp., 22hr, 23°C ½ hr recovery % set 27 24hr recovery % set 19Tensile Strength ISO 7214 1998 kPa 320Tensile Elongation % 130Tear Strength BS EN ISO 8067 1995 N/m 495Shore Hardness OO Scale ISO 868 1985 10mm cell/cell thickness OO 50Recommended operating Internal °C +100 maxtemperature range* -70 minThermal Conductivity ISO 8302 1991 W /m.K 0.0392 mean temp of 10°CFlammability Automotive FMVSS.302 – Burn rate <100mm/min. Pass: 12 mm and thicker Horizontal Burn Rate ISO 7214 1998 5mm thick mm/sec 2.1 13mm thick mm/sec 1.5Durometer 50 Shore 00Water lbs/ft3 5%

MPC0311


CLOSURE-FOAM™ products represent yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

Typical application

UV resistance

Interlocking dovetails

Additional colors are available upon request.

anglekut™

anglekut™

Weather-tite™ Sealant/adheSive

roof boots™

x-seal™

Mastix™

CLosUre FoaM™

re2™

lp2™

Fastenersflex-o-vent™

Clip sCrews

Clips

MarCo weaTHer-TiTe sysTeM™

Width

Height

Valley Thickness(Web)

Center to Center

(Pitch)

Terms for help in purchasing process

It’s simple, really. You want a door that looks good, works and seals well, holds up to use and weather abuse, and is a good value. And with that in mind, there’s an open and shut case for Marco’s Weather-Tite™ Doors.

Marco’s AS series door models are all steel…with an all steel frame, and and all steel 26 ga. skin. The panel is filled with polyurethane, creating an effective thermal break, and for rigidity, strength and insulation.

The nylon non-collapsible lockset insert helps eliminate moisture which can cause swelling, shrinking, and lock loosening. And with its inner design, it puts the frame on the inside of the door for a quality, commercial appearance.

When closed, the special rolled edge on Marco’s Weather-Tite™ doors creates a flat surface top to bottom, side to side, for a real, dependable seal every time.

The AS1, AS2, AS3, and CHAS3 feature a 3-1/2” frame width. The CHAS5 features a hefty 5” frame width, for maximum strength. All four? or five? AS models come with 16 Ga. pre-painted finish over hot dipped galvanized steel.

The economical A3 features a 3-1/2”, .63 prefinished aluminum frame.

All five door models have common header/threshold, nailing and non-nailing jamb, and

meet handicap specifications. Plus, the dual contact weather strip really seals the deal.

These value-priced doors come with fixed-pin hinges, 2-3/4” backset standard, and are pre-hung with 4-way universal swing (see swing information on back) to prevent last minute jobsite changes..

The AS1 model comes in white with a special woodgrain (paintable) finish. Marco’s other four steel-frame model doors are available in white—with brown, bronze, and clay available as special order. The A2 aluminum frame model is available in mill finish—with white available as special order.

Other options on all door models include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Ga. skin.

So if you’re trying to pick the best door, remember—Marco’s Weather-Tite™ doors have a real edge. A rolled, dependable seal edge.

A Rolled edge foR A ReAl SeAl.

W e A t h e R - t i t e™ d o o R S :

• Rolled edge creates dependable seal• Dual contact weather strip• Thermal break keeps hot and cold outside• 4-way universal swing prevents jobsite change problems

• Choose all steel or aluminum frame• Frames are 3-1/2” or 5”• All steel 26 Ga. skin• Non-collapsible lockset insert• Inner lock design for quality looks

Weather-Tite™ Doors represent yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the metal building industry.


U.S.: 9410 E. 54th Street | Tulsa, OK 74145 | 1.800.800.8590 | Fax: 1.918.622.4536

Canada: 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | Fax: 1.306.775.0072

Rolled edgeCreates a dependable, Weather-Tite™ seal

4-wAy uNIveRsAl swING4-Way Universal SwingTo prevent last minute jobsite change problems

theRmAl bReAkHelps keep hot and cold outside

loCkseTNon-collapsible insert for sealing and security

pANelThick panel for durability

WeAtheR StRipDual contact for a better seal

skINAll steel, 26 Gauge strength(24 Gauge optional on some models)

Face Face on on hinge opposite Colors Frame side side available

Weather-Tite™ 3-1/2" 1-9/16” 15/16” AS1 Economy Narrow Steel Profile Steel

Weather-Tite™ 3-1/2” 15/16” 15/16” Standard: A2 Economy Narrow Mill Finish Aluminum Profile Special Order: .63 White Pre-finished Aluminum

Weather-Tite™ 3-1/2" 15/16" 15/16" Standard: AS2 Standard Narrow White Profile Special Order: Steel Brown, Bronze, Clay

Weather-Tite™ 3-1/2" 1-1/4" 1-7/8" Standard: AS3 Extra Duty Steel White Special Order: Brown, Bronze, Clay Weather-Tite™ 3-1/2" 1-7/8" 2-7/16" Standard: CHAS3 for 40" White Heavy Duty R.O. Special Order: Steel Brown, Bronze, Clay

Weather-Tite™ 5" 1-7/8" 2-7/16" Standard: CHAS5 for 40" White Maximum Duty R.O. Special Order: Steel Brown, Bronze, Clay

Options available: Windows, Deadbolt lockset, Door Closer, Double Door with astragal (no center post), 24 ga. skin

Woodgrain only available in white, Standard skin available in Brown, Bronze and Clay.

MPC0910

Marco Weather-Tite™ Door models

AS2weather-Tite™ As2• Rolled edge creates dependable seal• Dual contact weather strip• All steel, 3-1/2” narrow profile frame

• Thermal break keeps hot and cold outside

• 4-way universal swing prevents jobsite change problems

• All steel 26 Gauge skin• Full 1-3/4” thick panel• Non-collapsible lockset insert• Inner lock design for quality looks

Marco’s AS2 is all steel…with an all steel frame, and all steel 26 Gauge skin. The 1-3/4” thick panel is filled with polyurethane to R-12 value for rigidity, strength and insulation.

The AS2 features a 3-1/2” frame width (1 9/16” face on hinge side, 15/16” face on opposite side), with 16 Gauge pre-painted finish over hot dipped galvanized steel. The frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The AS2 is available in white—special order brown, bronze, and clay. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

All steel frameThe 3-1/2” (1 9/16” hinge side face; 15/16” opposite side face) all steel frame is all about strength, from its 16 Gauge pre-painted finished over hot dipped galvanized steel, to its common header/threshold and nailing and non-nailing jamb.

standard steel Frame Door

CHAs3weather-Tite™ CHAs3• Rolled edge creates dependable seal• Dual contact weather strip• All steel, 3-1/2" wide frame (for 40” R.O.)



• All steel 26 Gauge skin (also available in 24 Gauge)

• Full 1-3/4” thick panel• Non-collapsible lockset insert• Inner lock design for quality looks

Marco’s CHAS3 is steel…with an all steel frame, and all steel 26 Gauge skin. The 1-3/4” thick panel is filled with polyurethane to R-12 value for rigidity, strength and insulation.

The CHAS3 features a 3-1/2” frame width (1-7/8” face on hinge side; 2-7/16” face on opposite side), with 16 Gauge pre-painted finish over hot dipped galvanized steel. The frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The CHAS3 is available in white—special order brown, bronze, and clay. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

All steel frameThe 3-1/2” (1-7/8” hinge side face; 2-7/16” opposite side face) all steel frame is all about strength, from its 16 Gauge pre-painted finished over hot dipped galvanized steel, to its common header/threshold and nailing and non-nailing jamb. It allows for a 40” wide R.O.

Heavy Duty steel Frame Door

A2weather-Tite™ A2• Rolled edge creates dependable seal• Dual contact weather strip• pre-finished, 3-1/2" narrow profile aluminum frame



• Aluminum 26 Gauge skin• Full 1-3/4" thick panel• Non-collapsible lockset insert• An economic choice

This economical door has an aluminum (.63) frame, and the 1-3/4" thick panel includes a steel 26 Gauge skin and is filled with polyurethane to R-12 value for rigidity, strength and insulation.

The A2 features a 3-1/2" frame width (15/16" face on hinge side, 15/16” face on opposite side. The aluminum frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The A2 is available in mill finish—special order white. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

Economical aluminum frame door with special dependable-seal Rolled Edge.

Aluminum frameThe 3-1/2” aluminum (.63) frame makes this a practical, economical choice, with common header/threshold and nailing and non-nailing jamb.

economy Aluminum Frame Door

CHAs5weather-Tite™ CHAs5• Rolled edge creates dependable seal• Dual contact weather strip• Aluminum, 5" wide frame (for 40” R.O.)



• All steel 26 Gauge skin (also available in 24 Gauge)

• Full 1-3/4" thick panel• Non-collapsible lockset insert• Inner lock design for quality looks

Like the other doors in Marco’s AS series, it’s all steel…with an all steel frame, and all steel 26 Gauge skin. The 1-3/4" thick panel is filled with polyurethane to R-12 value for rigidity, strength and insulation.

The CHAS5 features a 5” frame width (1-7/8” face on hinge side, 2-7/16” face on opposite side), with 16 Gauge pre-painted finish over hot dipped galvanized steel. The frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The CHAS5 is available in white—special order brown, bronze, and clay. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

All steel, extra wide frame, heavy duty door with special dependable-seal Rolled Edge.

All steel frameThe 5” (1-7/8” hinge side face; 2-7/16” opposite side face) all steel frame is all about strength, from its 16 Gauge pre-painted finished over hot dipped galvanized steel, to its common header/threshold and nailing and non-nailing jamb. It allows for a 40” wide R.O.

Maximum Duty steel Frame Door

AS3weather-Tite™ As3• Rolled edge creates dependable seal• Dual contact weather strip• All steel, 3-1/2" frame• Thermal break keeps hot and cold outside



Marco’s AS3 is steel…with an all steel frame, and all steel 26 Gauge skin. The 1-3/4” thick panel is filled with polyurethane to R-12 value, creating an effective thermal break, and for rigidity, strength and insulation.

The AS3 features a 3-1/2” frame width (1-7/8” face on hinge side; 2-7/16” face on opposite side), with 16 Gauge pre-painted finish over hot dipped galvanized steel. The frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The AS3 is available in white—special order brown, bronze, and clay. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

All steel frameThe 3-1/2” (1-7/8” hinge side face; 2-7/16” opposite side face) all steel frame is all about strength, from its 16 Gauge pre-painted finished over hot dipped galvanized steel, to its common header/threshold and nailing and non-nailing jamb. It allows for a 40” wide R.O.

extra Duty steel Frame Door

AS1weather-Tite™ As1• Rolled edge creates dependable seal• Dual contact weather strip• All steel, 3-1/2” narrow profile frame




Marco’s AS1 is all steel…with an all steel frame, and all steel 26 Gauge skin. The 1-3/8” thick panel is filled with polyurethane to R-9 value for rigidity, strength and insulation.

The AS1 features a 3-1/2" frame width (1 9/16" face on hinge side, 15/16" face on opposite side), with 16 Gauge pre-painted finish over hot dipped galvanized steel. The frame also has common header/threshold and nailing and non-nailing jamb and meets handicap specifications. Plus, the dual contact weather strip really seals the deal.

The AS1 is available in white with a special woodgrain paintable finish.Special order brown, bronze, and clay. Woodgrain is only available in 3/0 x 6/8 and smaller. Other options include windows, deadbolt lockset, door closer, double door with astragal (no center post), and 24 Gauge skin.

All steel frameThe 3-1/2" (1 9/16" hinge side face; 15/16" opposite side face) all steel frame is all about strength, from its 16 Gauge pre-painted finished over hot dipped galvanized steel, to its common header/threshold and nailing and non-nailing jamb.

economy steel Frame Door

DooR swING

INsIDe

lH swINGRH swING

DouBleDooR swING

INsIDe

lH swINGRH swING

oUtSide

DooR swING

lH swINGRH swING

oUtSide

DouBleDooR swING

lH swINGRH swING

Rolled edge and thermal break Non-collapsible nylon lockset insert Dual contact weather strip

Proper ventilation is important to meet building codes, to reduce utility costs, and reduce long-term building damage. Flex-O-Vent provides plenty of cooling air flow.

flex-o-vent

extremely durable polyester

flame-resistant / clog-resistant / tear-resistant

economical / long lasting

• Won’t absorb moisture, which can freeze and block all ventilation

• Easy one person installation

• 40 year limited warranty

• ASTM E 84 tested/rated

Specially formulated polyester has been manufactured from recycled material and is recyclable.

Universal Ventilation Material.

Polyester Ventilation Material

Flex-O-VentFlexibility,versatility,durability. Universal Ventilation Material

Marco Industries Corporate: 9410 E. 54th Street | Tulsa, OK 74145 | 1.800.800.8590

Marco Industries Canada: 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573

SpecificationsNet Free Area .......................19 square inches per Linear Foot-ridge

1-1/2" x 3" x 10' ....................Rib heights 11/4" and lower

Air Permeability ....................760 Cubic Feet per minute

Cold Cracking .......................-55˚C (-130˚F)

Snow Infiltration ..................0

Tear Strength .......................3.5 ppi

Tensile Strength ...................16 psi – Elongation 175%

Compressive Strength ..........1.8 psi @ 75%

Abrasion ...............................No Damage

100 mpg Wind-driven Rain ..No Leakage Non-Profile Sensitive

MPC0311


Flex-O-Vent represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

Easy Installation

Universal Fit

Flexible Design

anglekut™

anglekut™


roof boots™

x-seal™

Mastix™

FlEx-O-VEnT™

re2™

lp2™

Fasteners

Clip sCrews

Clips ClosureFoam™

MArcO WEAThEr-TiTE SySTEM™

How fitting.Custom contours keep water out...bring air through.

For those looking for a ventilation system to provide the ultimate ventilation benefits at a cost lower than traditional fans, turbines, and louvers, the WEATHER-TITE™ LP2™ RIDGE VENT removes heat and moisture, prevents rot, extends paint life, limits mold growth, ice damming, and reduces excessive heating and air conditioning costs.

The product is made from the non-fabric-covered Python™ vent recycled

material. This strong, durable, modified polyester is a non-woven,

non-wicking, fiber-based matting. Its special cut contours are designed to provide

a custom, low-profile fit for any pitch and most major metal roof profiles. These features add up to a superior net free ventilation area that still helps keep out moisture, pests, dust.

Plus, LP2™ can be installed by just one person in two easy steps. In fact, the screw bed and industrial strength peel and stick adhesive pre-applied to LP2™ makes this one of the easiest installations imaginable.

The LP™ system improves attic ventilation, eliminates condensation, and is easy to install… a fitting combination that’s hard to beat.

• Lower, custom-fit profile• Moisture and pest barrier• Non-obtrusive appearance• Reduces utility costs• One-person, easy installation

LP2 WEATHER-TITE RIDGE VENT™

Low Profile Ridge Vent For Agricultural, Commercial and Standing Seam Metal Panels

BILLS LOWKEEP ENERGY

ENERGY EFFICIENT PRODUCT

Custom contours

Specially formulated polyester has been manufactured from recycled material and is recyclable.

LP2 WEATHER-TITE RIDGE VENT™

Low Profile Ridge VentFor Agricultural, Commercial and Standing Seam Metal PanelsLower, custom-fit profileCustom contours fit any pitch, all major metal roof profiles, for either ridge cap application or roof-to-wall applications. LP2™ creates a low-profile look and a seal that helps keep out moisture.

Python™ non-clogging protection.Python™ is a single-layer, non-fabric-covered ridge vent re-cycled material made from silicone-coated fibers that prohibit clogging. This strong, durable, modified polyester allows the greatest air flow in and out of the attic.

Moisture, net free area and pest-free seal.The special cut contours plus a 2" Marco closure create an incredible WEATHER TITE™ seal to help keep out moisture, insects, dust, and plant materials.

Non-obtrusive appearance.The contours give this system a WEATHER TITE™ fit, and to the roof a non-obtrusive appearance to the roof.

Reduces utility costs.Excellent air flow means your metal structure stays cool while the heat escapes and adds up to reduced utility costs.

LP2 comes 75 feet to a box, in twenty-five 3-foot sections.

One-person, easy installation.LP2™ comes with a double bead of industrial strength adhesive. One person can simply remove the peel and stick strips to apply LP2™ to the metal roof, then secure the ridge cap over the LP2™ with fasteners or nails. It’s that easy!

Building code compliant.When properly installed with soffit or intake vents, LP2™ is building code compliant.

SpecificationsNet Free Area .......................Varies with profile based on 17 square inches per Linear Foot of ventilation materialDimensions vary with panel pitchAir Permeability ....................>>760 Cubic Feet per minuteCold Cracking .......................-25˚ FSnow Infiltration ..................0Tear & Tensile Strength ........Machine 25 ppi / Counter 25 ppiCompressive Strength ..........1.8 psi @ 75%Abrasion ...............................No Damage100 mph Wind-driven Rain .....................................No Leakage


Marco Industries Canada: 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | Fax: 1.306.775.0072MPC0910U.S. Patent Number 7,594,363Canadian Patent Number 2,503,414


LP2™ represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

Staying power• High quality adhesive• Joins metal to metal• Seals around windows, doors, more• Roll won’t telescope from heat before installation

• Adhesive really holds hot metal panels

Marco Industries has created a high quality trimmable joint and end lap sealing tape that solves the

adhesive failure problems associated with hot metal roofing and wall jobs.

Mastixtape™ is made with a superior adhesive which is non-staining, permanently flexible, and stays in place during extreme heat. It seals

around windows, doors, roof vents, stacks, access doors and other penetration points.

The adhesive actually prevents the product roll from “telescoping”…a common problem when other

adhesives get too hot and cause a tape roll to start losing its shape. Which then causes the installer more handling

problems and installation time.

Then, once Weathertite™ Mastixtape™ is applied, it truly adheres to the metal roof panel and stays in position even on the hottest days. So you don’t have to mess with a failing adhesive strip sliding down the hot metal roof before you can overlay the next roofing panel.

Don’t sweat your next metal roofing job. Choose Weathertite™ Mastixtape™ and get the job done easier and faster, even on the hottest days.

Choose the sealant that will stick aroundbefore and after installation.

Metal to metal high quality sealing tape…that really stays in place.Versatile• Mastix is a trimmable end lap sealing tape that

joins metal to metal, and seals around windows, doors, roof vents, stacks, access doors and other penetration points.

Prevents product telescoping.• Mastix superior adhesive keeps the product roll

intact and non-telescoping, even on hot days.

Keeps metal roofing panel in place• Apply Mastix to a hot metal roofing panel. It will

stay put, while you place the panel. No melting,

oozing adhesive allowing panels to slide and making your installation harder.

Non-staining, permanently flexible.• Mastix won’t stain, and it stays flexible, making it

the perfect adhesive tape for almost every metal roof application.

Technical CharacteristicsChemical Product and Company IdentificationProduct Name: ...................... Mastix™ Butyl TapeChemical Name: .................... IsobutyleneChemical Family: .................. Butyl Mixture

Health Hazard: ....................... 0-MinimalFlammability Hazard: ............ 0-MinimalReactivity Hazard: .................. 0-Minimal

Hazardous Identification• Based on data available to Marco Industries, none of the components in this product are considered hazardous according to OSHA Hazard communication Standard 29CFR 1910,1200.• The Composition of this mixture is proprietary information. In the event of a medical emergency, compositional information will be provided to a physician or nurse.

Fire HazardsFlash Point: ......................... >400˚F (204˚C)Method: ................................. Pensky Marten closed cup

Extinguishing Media: ............ Dry chemical, Carbon dioxide, Foam, WaterSpecial Fire-FightingProcedures: ........................... Large quantities of water will extinguish.

Do not enter confined space without proper protective equipment.

Hazardous CombustionProducts: ............................... Carbon monoxide. Carbon dioxide.

Physical and Chemical PropertiesVolatile (WL)%: ..................... 0Solubility in Water: ................ InsolubleSpecific Gravity (H20=1): ..... 1.59-1.64Evaporation Rate: .................. Not applicableAppearance: .......................... Soft, pliable gumColor: .................................... Q-126 Off-white to gray Q-126BB Black Q-126-10 Off-white to grayOdor: ..................................... None

Sizes AvailableSize Rolls / Case Case / Pallet 3/32 x 3/8 x 45 45 / case 30 / pallet 3/32 x ½ x 45 22 / case 50 / pallet 3/32 x ¾ x 45 24 / case 36 / pallet 3/32 x 1 x 45 24 / case 30 / pallet




Mastix™ represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0910

M-Clips

A standing seam roof is only as reliable as the clips that hold it all together.

Which is why Marco offers two types of clips made from premium, 22-gauge steel that will not fail under extreme heat, ice, rain or wind. We’ve ensured that the utmost quality is in your hands–our clips are completely free of burrs, preventing rust and other corrosion problems. Our clips are also inspected during the production process to guarantee all dimensions will match factory panel specifications.

As opposed to “thru-fastened” roofs, standing seam roofs are made of spring joints that fasten panels together along their edges. Because

standing seam roofs are designed to float and the fasteners are concealed, they do not leak. Our clips function in much the same way–they are hidden, fastened to the roof while the panel is pressed down onto the clip, locking it in place. Simple,

effective and absolutely reliable.

Whatever your standing seam roof requires–snap lock clips, fixed clips, slider assemblies, bearing plates or hidden hangers, we have you covered with the M-Clips roof clip system. Our Weather-Tite system keeps everything out of sight.

Hidden clips that fasten standing seam roof panels together

The Marco Clip System

TM

TM

Our statistical process control system

maintains all dimensions and met tolerances

to ensure the utmost precision and quality.

While our competitors’ lower grade steel clips

may have burrs that cause leaks and rust, our

M-clips™ are made from premium grade steel

that are free of burrs. Be sure your project is

Weather-Tite™ with Marco’s

M-clips™.

MECHANICAL SEAM

2

MechanicalSeam

SnapLock

M-Clips Installation

SLIDER ASSEMBLY

HEAVY DUTY

STANDARD

STANDARD

3

CORPORATE 9410 E. 54th Street | Tulsa, OK 74145 | 1.800.800.8590 | Fax: 1.918.622.4536

CANADA 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | Fax: 1.306.775.0072

MechanicalSeam

CLIP NAME1-5/8" Fixed Clip

1-5/8" Fixed Clip

2-1/8" Fixed Clip - N

1-1/8" Fixed Clip

1-5/8" Fixed Clip

1-5/8" Fixed Clip

1-1/8" Fixed Clip

1-5/8" Fixed Clip

1-5/8" Fixed Clip

2-1/8" Fixed Clip - N

1-1/8" Fixed Clip

1-5/8" Fixed Clip

2-1/8" Fixed Clip

1-1/8" Fixed Clip

1-5/8" Fixed Clip

2-1/8" Fixed Clip - M

2-1/8" Fixed Clip - M

1-1/8" Fixed Clip

1-5/8" Fixed Clip

1-5/8" Fixed Clip

1-1/8" Fixed Clip

1-5/8" Fixed Clip

2-1/8" Fixed Clip - W

2-1/8" Fixed Clip - W

STANDARDMRC-106

MRC-107

MRC-108

MRC-105

MRC-107

MRC-106

MRC-105

MRC-106

MRC-106

MRC-108

MRC-105

MRC-107

MRC-145

MRC-105

MRC-107

MRC-109

MRC-109

MRC-105

MRC-107

MRC-107

MRC-104

MRC-106

MRC-110

MRC-110

MANUFACTURER PANEL NAMEEnglert - A1300 Mechanical Seam Standard

Englert - A1301 Mechanical Seam Special

Englert - S2500 Mechanical Seam

ESE - 1" Mechanical Seam

ESE - 1-1/2" Mechanical Seam

Knudson - P-2401 1.5" Mechanical Seam

Knudson - VP-21 1" Mechanical Seam

Knudson - VP-21 1.5" Mechanical Seam

Knudson - KR-24 1.5" Mechanical Seam

Knudson - KR-24 2" Mechanical Seam

Metal Forming - 1" Mechanical Lock

Metal Forming - 1.5" Mechanical Lock / Quadra Pro - TM

Metal Forming - 2" Mechanical Lock / Quadra Pro - TM

New Tech - SS100 Mechanical Seam

New Tech - SS150 1.5" Mechanical Seam

New Tech - SS200P - 2" Mechanical Seam

New Tech - SS210A - 2" Mechanical Seam

Roll Former - VS-150 1" Mechanical Seam

Roll Former - VS-150 1-1/2" Mechanical Seam

Roll Former - VS-150 1-1/2" Mechanical Seam Plus 50 Profile

Zimmerman - SS-1000 1" Standing / Mechancial Seam

Zimmerman - SS-1500 1-1/2" Standing / Mechanical Seam

Zimmerman - SS-2000 2" Mechanical Seam

Zimmerman - SS-2000A 2" Mechanical Seam

GAUGES24

24

24 / 22

24

24

24

24

24

24

24 / 22

24

24

24 / 22

24

24

24 / 22

24 / 22

24

-

24

24

24

24 / 22

24 / 22

ALTERNATEMRC-134 - Slider Assembly

MRC-128 - Slider Assembly


-



-




-



-




-



-




Our fixed mechanical seam clips keep everything in place–with a slider assembly that can stand up to extreme wind stress. The slider assemblies for panels over 40’ allow for thermal expansion between the panels during intense hot or cold temperatures. Heavy duty and UL-listed to withstand all types of environments, including excessive heat, ice and hurricane-force winds.

STANDARD

SLIDER ASSEMBLY

SNAP LOCK + GUTTER HANGER + BEARING PLATE

4

SnapLock

CLIP NAME STANDARDMANUFACTURER PANEL NAME ALTERNATE1-1/2" Snap Lock Clip

1-1/4" Snap Lock Clip



1" Snap Lock Clip - Heavy Duty



-




1" Snap Lock Clip - Light Gage


100 SLZ - Snap Lock

Has a nail strip. Does not use a roof clip.

Has a nail strip. Does not use a roof clip.

100 SLZ - Snap Lock


MRC-127

MRC-102

MRC-100

MRC-100

MRC-130

MRC-112

MRC-101

MRC-148

MRC-101

MRC-101

MRC-102

MRC-140

MRC-141

MRC-103

NA

NA

MRC-103

MRC-101

Englert - A1000 Snap Lock



Englert - S2000 Snap Lock

Metal Forming - 1" Snap Seam / Quadra Pro - TM

Metal Forming - 1.5" Snap Seam / Quadra Pro - TM

Metal Forming - 1.75" Snap Seam / Quadra Pro - TM

New Tech - SS450SL - 1-1/2" Snap Lock

New Tech - SS675 - 1-3/4" Snap Lock

Roll Former - SLP-175 Snap Lock

Roll Former - VS-150 1-1/2" Snap Lock

Roll Former - Staylock 1" Snap Lock

Roll Former - Staylock 1-1/2" Snap Lock

Zimmerman - SL-1000 1" Snap Lock

Zimmerman - SLC-1000 1" Snap Lock Convertible

Zimmerman - SLC-1500 1.5" SnapLock Convertible

Zimmerman - SL-1500 Heavy Duty 1-1/2" Snap Lock

Zimmerman - SL-1750 1-3/4" Snap Lock

-

-

MRC-113 - Heavy Duty 3-1/2" Base


-


MRC-143 - 22 gage Economy 2" Base

MRC-114 Heavy Duty 3-1/2" Base

-



-

-

-

-

-

-

-


Our hard-working snap lock clips make attaching roof panels a snap. Use Marco screws to secure and simply snap your roof into place. Heavy-duty or UL-listed to withstand all types of environments, including excessive heat, ice and hurricane-force winds.

GAUGES24

24

18

18

18

18 / 22

18

-

18

18

24

24

24

24

NA

NA

24

18

STANDARD

HEAVY DUTY

5



GutterHangersSIZE

INSTALLATION DIAGRAM

INSTALLATION DIAGRAM

STANDARD GUTTER HANGER

STANDARD BEARING PLATE

5" Hidden Hanger – Aluminum

5" Hidden Hanger – Steel

6" Hidden Hanger – Aluminum

6" Hidden Hanger – Steel

Side profile of gutter hanger

available in both 7” and 8” SizeS in aluminum and Steel

BearingPlateSIZE3x3 Bearing Plate

4x4 Bearing Plate

3x4 Bearing Plate

5x5 Bearing Plate

6x6 Bearing Plate

bearing plate

Clip

foam baSe

roof SubStrate

Our hangers are much stronger than most hangers on the market because of the unique double strengthening adhesive bead which wraps around the back and front of the hanger.

Available in multiple gauges and sizes, our bearing plate secures a foam base between substrate and metal.

GUTTER HANGER

BEARINGPLATE

Ordering M-clips? For easy installation, don’t forget to order...

Like all other Marco products, our clip screws are made of heavy-duty alloys that stand up to tough rooftop conditions. Both our ClipScrews and UltraLo models fasten smoothly and securely to prevent canning on roof panels–a hallmark of poor product quality.

To make sure that your standing seam roof is truly Weather-Tite, make sure to ventilate the ridgecap with LP2 – a durable, non-woven, and non-wicking custom profile ridge vent that is flame and tear resistant.

Standard clip screws have regular profile heads. When those regular clip screws don’t fasten tight, it can cause dimpled roof panels and result in serious loose panel problems. Problem solved with Marco’s low profile clip screws – available in both QuikGrip™ and QuikDrill™ – with heads that are 50% lower than standard clip screws.

QuikGrip™ and QuikDrill™ ClipScrews™ have a deep thread that pulls the fastener tighter and resists pullout better. And with the 17pt special thread design, you’ll get an even quicker drill or grip on 24 and 26 ga. metal.

For a low profile clip screw that causes absolutely no canning or telescoping – which can add a “wavy” appearance to your standing seam roof – choose Marco’s UltraLo clip screw.

UltraLo’s head is 75% lower than a standard clip screw. It is also designed with an aggressive double lead thread for faster installation. Available in a regular Phillips #2 head or a Phillips/Square Diamond combo head, a 17 pt., and TripleGuard Gold coating, this heavy duty clip screw is made to last.

Custom contours fit any pitch, all major metal roof profiles, for either ridge cap application or roof-to-wall applications. LP2™ creates a low-profile look and a seal that helps keep out moisture. Python™ is a single-layer, non-fabric-covered ridge vent re-cycled material made from silicone-coated fibers that prohibit clogging. This strong, durable, modified polyester allows the greatest air flow in and out of the attic. The special cut contours plus a 2” Marco closure create an incredible WEATHER TITE™ seal to help keep out moisture, insects, dust, and plant materials.

ClipScrews

The Expanding Marco Weather-Tite System™

ANGLEKUT™

Custom Beveled Inside/Outside Closure

M-CLIPS™

Many clips and fastenersfrom which to choose

TITEBONd SEALANTDurable & flexible

x-SEAL™ Expandable Foam Tape

MASTIx™

Butyl Tape

WEATHER-TITE dOORS™

Rolled Edge, Reliable Seal (5 models)

CLOSURE fOAM™

Inside/Outside Closures with adhesive

ROOf BOOTS™

Pipe Flashing

RE2™

Non-Warping, Non-Corroding Reroof Retrofit Spacer

SILL-RITEMulti-use sill plate sealer provides a long-lasting seal

LP2™

Low Profile Vented Closure as ridge vent

QUIKGRIP™

Metal to wood fastener

fLEx-O-vENT™

Flexible Foam Ridge Vent as universal ridge vent

QUIKdRILL™

Metal to metal fastener

For nearly twenty years, Marco Industries™ has been delivering award-winning products to the metal building industry that offer easy installation, remarkable building ventilation, lower utility costs, extreme durability, and outstanding warranties...products that are economically and ecologically smart. Choose Marco for Everything You Need To Make Your Structure Weather-Tite.™


M-clips™ represent yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.



MADE IN USA

Helping structures

breathe.Good air in. Bad air out. Just like you, buildings do better if they breathe properly. Which requires good ventilation. That’s exactly what Marco’s Python™ Ridge Vent does—helps ventilate buildings better.

Python™ is a single-layer ridge vent which is not fabric covered and comes in a coil. It’s a strong, durable, modified polyester and can be used under ridge caps,

under ridge shingles, and as a fascia vent.

Python’s non-woven, non-wicking, fiber-based matting has no external baffle, so dirt and snow trapping is greatly reduced. It helps keep out insects, dust, and moisture. As fascia vent, it helps eliminate mold build-up. Yet, with a properly balanced attic ventilation design to meet code, Python™ allows fresh air to be drawn into the attic and allows hot or stale air from inside to be

drawn out through the ridge vent. The result? A cooler attic in summer and a drier attic in winter.

That kind of ventilation helps reduce utility costs. Plus, Python™ is made from recycled plastic, so builders can be confident they’re using a green building product.

Python is light and flexible, so it’s easy to handle and to install. And you can use every piece, so there’s virtually no waste.

Of course, builders want to know what type of buildings they’re limited to with Python™. The answer: Python™ is for use with all roof applications. And with many sizes available—including for just about any fascia, you can take advantage of all of Python’s building benefits on almost any building project.

So, with Python™, you’re building with a recycled product that helps reduce utility costs by drawing cooler air in and pulling stale air out. There’s no complicated fitting or wrapping, making it fast and easy to install. It’s economical. And it’s extremely durable and weather resistant.

That should make you—and your building—breathe a lot easier. Compliments of Python™.

• For ALL roof applications• Under roofing, under hip/ridge shingles, and as an exhaust/intake fascia vent

• Keeps attics cooler in summer, dryer in winter• Helps reduce utility costs• Non-wicking, helps keep out insects, dust, moisture• Durable, made from recycled plastic

And builders breathe easier.

5 0 - y e a r l i m i t e d w a r r a n t y

1 2 3

4 5 6

MIAMI DADE COUNTYAPPROVED

1 2 3

4 5 6

Low profile.Python is a single-layer ridge vent in a coil. Its low profile helps prevent puckering or buckling under the ridge cap.

Easy to handle, easy to install.It’s light, flexible and there’s no difficult fitting or wrapping.

Multi-use, and with all roof applications.Python can be used under roofing, under hip/ridge shingles, and as an exhaust/intake fascia vent...no matter what roof is on your building.

No fabric wrap, no external baffle.Nothing to cause clogging, deterioration, or dirt and snow trapping. Yet, Python helps keep out insects, dust, and moisture.

Strong and durable.Python is non-woven, non-wicking and resists damage from ice, hail, and other weather, which means fewer warping and loosening problems. And, it helps to prevent corrosion, rust, and brittleness.

EconomicalPython’s flexibility means there’s no shipping or installation crack or dent damage. There’s no waste with Python—you can use every piece. And its durability means it lasts for a long time.

A green product for today’s building projects.Made from more than 90% recycled plastic material (more than 30% post consumer content). And since Python can help draw cool air into the attic and hot air out in summer, it can help reduce utility costs.



PY-3000-50N 1” x 3” x 50’ (2 Pack) / 2 bags of nailsPY-6000-50N 1” x 6” x 50’ 2 bags of nailsPY-8000-50N 1” x 8” x 50’ 2 bags of nails

PY-8000-20N 1” x 8” x 20’ 1 bag of nailsPY-1050-20N 1” x 10.5” x 20’ 1 bag of nailsPY-1175-20N 1” x 11.75” x 20’ 1 bag of nails PY-3410-20N 3/4” x 10.5” x 20’ 1 bag of nailsPY-3480-20N 3/4” x 8” x 20’ 1 bag of nails


Python represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0910

Composition and Materials: UV stable, polyester composite. Maintenance: Properly installed, is maintenance-free. Color: Dark GreyInstallation: Easily installed without special tools. Joints can be simply cut square,

butted and caulked without connectors of fables. Won’t dent, crack, or rust, and has no sharp edges. Is flexible, easy-to-handle and transport, and conforms to any roof pitch from 2/12 to 20/12. Must be installed with soffit vents to meet HVI recommendations.

Air flow is unrestricted by any fabric covering. Patent pending. Dade County approved.

Part No. Size Nails

Air Permeability ...............................ASTM D737 ...................760 cu. ft. per minuteTear and Tensile Strength ................ASTM D1294·86 ............Tear: Machine 25 p.p.i. Counter 25 p.p.i. ASTM D2261·83 ............Tensile: Machine 25 p.p.i. Counter 25 p.p.i.Self-Ignition Temperature................ASTM D1929 .................963° F.Cold Crack Resistance ....................GLIT C115 .....................–25° F.Snow Infiltration .............................CRL 5704 ......................–0– Net Free Area for 3/4”: 18 sq. in. per lin. ft. Net Free Area for 1”: 19.4 sq. in per lin. ft.

Typical Physical PropertiesPython must be installed on roofs with a minimum of 3/12 pitch (14°)

1” x 10.5” x 20’ 36 1872 1” x 11.75” x 20’ 36 1872 1” x 8” x 20’ 45 2340 1” x 8” x 50’ 22 1144 1” x 3” x 50’ 14 308 3/4” x 8” x 20’ 45 2340 3/4” x 10.5” x 20’ 36 1872

Part Pkgs per pallet Pkg per truck

Pallet and truck quantity

MADE IN THE USA

MIAMI DADE COUNTYAPPROVED

T H EB U I L D I N G F A S T E N E R S

F A M I LY O F F A S T E N E R S

Crimped washer heads show polyurethane’s superior durability while powder coating can chip and flake.

PaintingOptions

POWDER COATPOLYURETHANE

MATCHTECH

PAINT + TESTING

MatchTech™ is Marco Industries’ state-of-the- art, high quality polyurethane paint for all of your fastener needs. MatchTech™ uses Imron 6000 from DuPont. Due to the added amount of polyurethane in Imron 6000, it produces a rubber-based material which eliminates chipping, especially when lobe sockets are used.

QUALITY:Offers unsurpassed durability and chemical resistance.

CONSISTENCY: High quality coating makes your fasteners last, and keeps

Marco’s use of polyurethane paint makes it the most durable paint coating technology in the industry.

Unlike typical powder coating paint processes, which can end up cracking, flaking, chipping, and disintegrating under pressure, polyurethane paint has a rubbery

compound that allows it to bend and bounce back under stress without cracking, flaking, or chipping.

you coming back for more.

LIMITLESS POSSIBILITIES: There are endless color possibilities with this state of the art color system.

QUICK:Non-standard color matches can be produced within a 24 to 48 hour turn around using our in house color eye computer station.

The world’s best fasteners – now in any color, any time.

SUPERIOR POLYURETHANE PAINT COATING

2



TestingLaboratoryMarco Industries and Sherry Laboratories

3

Marco Industries has partnered with Sherry Laboratories for product testing and validation. Marco’s partnership with Sherry Laboratories ensures that all products can withstand the most brutal elements in the harshest climates North America has to offer.

Sherry Laboratories has built a reputation as an industry leader in the field of metallurgical testing by meeting and exceeding customers’ expectations for accuracy and time requirements for more than 60 years.

Sherry Holdings LLC is five premier testing companies combining to provide uniquely accredited testing, technical expertise and services of superior quality through eight testing facilities. Founded in 1947, Sherry has been adding value to Marco Industries by providing efficient, timely and responsive testing services.

Few laboratories around the world carry the range of professional accreditations and approvals enjoyed by Sherry Laboratories.

Sherry’s metallurgical laboratories have been accredited through Nadcap and the American Association of Laboratory Accreditation (A2LA). They also meet the requirements of ISO 17025, and the general requirements for the Competence of Calibration and Testing Laboratories for Mechanical, Chemical and Fastener testing as outlined in the Fastener Quality Act (FQA).

OEMs, fabricators and end users rely on Sherry Laboratories to test their metals, exotic alloys and polymers in accordance with standards set forth by a number of organizations, including the American Society for Testing and Materials (ASTM), American Society of Mechanical Engineers (ASME), American Petroleum Institute (API), American Welding Society (AWS), American Association of State Highway and Transportation Officials (AASHTO), Federal, Military or individual customer specifications.

METAL2WOOD + METAL2WOOD-HD

The Metal2Wood fastener is designed to attach steel roofing and siding used in post-frame and residential metal roofing applications.

The high hex washer head provides driving stability, its HiLo threads make for superior holding strength, and the Type 17 point allows for quick installation. The bonded seal washer creates a truly Weather-Tite seal – even when driven at an angle.

Type 17 point drills with no “point walking,” reducing metal shavings that can become embedded in the rubber washer.

The mechanical zinc plating provides extended corrosion resistance.

The Metal2Wood HD is your “rescue screw.” It can replace nails or fasteners that have loosened and backed out of metal roofing and siding.

The EPDM rubber is vulcanized to the steel washer to prevent delaminating to form an excellent seal - even when driven at an angle. The 5/16" HWH with bonded sealing washer will cover the existing hole entirely, creating a watertight seal, even if stretched out by movement of the

metal roof. The mechanical zinc plating provides extended corrosion resistance.

8.25

10.321

12.495

15.068

16.867

10.587

#10 HiLo

ID OD

.214" .470"

SIZE HEAD CARTON QTY WEIGHT/M WASHER SIZES10 x 1"

10 x 1-1/2"

10 x 2"

10 x 2-1/2"

10 x 3"

12 x 3/4" STITCH

1/4" HWH

1/4" HWH

1/4" HWH

1/4" HWH

1/4" HWH

1/4" HWH

2500

2500

2000

1500

1000

5000

8.25

10.321

12.495

#10 HiLo

ID OD

.275" .590"


14 x 1-1/2"

14 x 2"

5/16" HWH

5/16" HWH

5/16" HWH

2500

2000

1500

STANDARD OPTIONAL

STANDARD OPTIONAL

TRIPLEGUARD MATCHTECH ELECTROPLATESURESHIELD

4

MAJOR DIAMETER

MINOR DIAMETER

HEAD ACROSSFLAT

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

25º TYPE 17

P O I NTD I A M ETE R

.191 / .202 .130 / .126 .246 / .251 2293 LBS. 60 IN-LBS. 1890 LBS.

MAJOR DIAMETER

MINOR DIAMETER

HEAD ACROSSFLAT

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

30º TYPE 17


.245 / .248 .185 / .178 .312 / .305 4272 LBS. 125 IN-LBS. 2995 LBS.

METALS

PLYWOOD OSB OAK HEMLOCK FIRSOUTHERN PINE SPRUCE PINE FIR

S U B STR ATE S

709 594 403 313 710 1185 495 1043 1895 654 1210

3/4 5/8 1/2 7/16 1" 1-1/2" 1" 1-1/2" 1" 1" 1-1/2"PuLL OuTSTRENGTH

METALS


S U B STR ATE S

845 646 377 296 1186 - 653 - - 668 -


NOM. GAUGE

THICKNESS

#10 x .472

#10 x .500

29

.015

379

422

26

.019

630

655

24

.024

723

795

M ATE R I A LAZ55 GALVALUME

DESIGNATION

PuLL OVERSTRENGTH

NOM. GAUGE

THICKNESS

14mm x .551

HWH

29

.015

493

493

26

.019

781

721

24

.024

1079

1042

22

.032

1352

1196

20

.038

1609

1420

M ATE R I A LAZ55 GALVALUME G-90 GALVANIZED

DESIGNATION

PuLL OVERSTRENGTH



5

REZISTOR + REZISTOR3

ReZistor is designed to fasten steel sheeting to wood, plywood, or OSB. It is used in post frame and residential construction.

The 5/16" cupped HWH with molded zinc-aluminum alloy provides protection against red rust on the head and washer. The Zinc Alloy Cap head provides more strength than common alloys.

ReZistor is an excellent choice for Galvalume and other long-life metal roof panels, and has a 40-year warranty – available upon request.

ReZistor3 is a smaller, cupped HWH that provides an attractive low-profile appearance versus large HWH fasteners. Intended as an alternative to the zinc-aluminum alloy head. It is also used to fasten steel roofing in post-frame and residential construction projects.

ReZistor3 is an excellent choice for Galvalume or other long-life metal roofs.

With a 40-year warranty – available upon request –ReZistor3’s stainless steel cap will never produce red rust.

13.006

15.904

17.326

22.124

9.065

#10 HiLo Zinc Alloy Cap

ID OD

- 11mm


10 x 1-1/2"

10 x 2"

10 x 3"

12 x 3/4" STITCH

5/16" CHWH

5/16" CHWH

5/16" CHWH

5/16" CHWH

5/16" CHWH

2500

2500

2000

1000

2500

9.4

11.0

#10 HiLo

ID OD

- 9mm


10 x 1-1/2"

1/4" HWH

1/4" HWH

3000

2500

The Type 17 point and transition threads generate greater holding strength and superior drill speed in various wood substrates.

Type 17 point drills 29 and 26 gauges every time.

THICKNESS

3mm

THICKNESS

3mm

STANDARD OPTIONAL

STANDARD OPTIONAL


6

MAJOR DIAMETER

MINOR DIAMETER

WASHERFACE DIAMETER

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

25º TYPE 17


.191 / .202 .126 / .130 .311 / .305 1344 LBS. 60 IN-LBS. 1804 LBS.

MAJOR DIAMETER

MINOR DIAMETER

WASHERFACE DIA

HEADACROSS FLAT

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

30º TYPE 17


.191 / .202 .126 / .130 .500 .250 / .244 2099 LBS. 60 IN-LBS. 1804 LBS.

METALS


S U B STR ATE S

706 593 403 312 708 1186 491 1044 1345 652 814


METALS

PLYWOOD OSB SOUTHERN PINE

S U B STR ATE S

669 398 238 1295 -

3/4 1/2 7/16 1" 1-1/2"PuLL OuTSTRENGTH

NOM. GAUGE

THICKNESS

#10 Type 17

29

.015

655

26

.019

1025


DESIGNATION

PuLL OVERSTRENGTH

NOM. GAUGE

THICKNESS

#14 x .550

26

.019

724


DESIGNATION

PuLL OVERSTRENGTH



7

LOPRO + 300SS

LoPro provides a quality, low profile appearance on sidewall applications installed into wood girts. With a round head with 6-lobe recessed driver, LoPro is specially designed to fit the 6-lobe recess with no paint damage.

The undercut EPDM rubber washer provides a secure seal even when driven at an angle.

And with yellow dichromate zinc plating for a longer

lifetime, LoPro is more rust-proof than typical plated fasteners.

The 300ss stainless steel HWH and bonded washer provide protection – even in the harshest environments.

The HWH design holds the EPDM rubber washer to provide a protected seal, even when driven at an angle.

300ss is an excellent choice for use in aluminum liner panel applications, but can also function well for animal confinement structures.

The type A point will tap a pre-drilled hole in steel, or will self-drill through aluminum lines panels.

10.1

SIZE HEAD CARTON QTY WEIGHT/M10 x 1-1/2" TRUSS 2500

7.9

9.9

SIZE HEAD CARTON QTY WEIGHT/M9 x 1"

9 x 1-1/2"

1/4" HWH

1/4" HWH

5000

2500

Type 17 point quickly penetrates steel siding and reduces metal shavings that can become embedded in rubber washer.

#10 T-25 HiLo

ID OD

- 8.5mm

WASHER SIZES

#9

ID OD

- 10mm

WASHER SIZES

THICKNESS

2mm

THICKNESS

2mm

LoPro comes with yellow dichromate plating

300ss comes with stainless steel plating

STANDARD OPTIONAL

STANDARD OPTIONAL


8

LoPro™

MAJOR DIAMETER

MINOR DIAMETER

HEAD ACROSSFLAT

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

25º TYPE 17


.191 / .202 .126 / .130 .500 T-25 TRUSS 2094 LBS. 60 IN-LBS. 2418 LBS.

MAJOR DIAMETER

MINOR DIAMETER

WASHERFACE DIA

HEAD ACROSSFLAT

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

25º TYPE 17


.189 / .183 .141 / .139 .38 / .32 .250 / .244 1134 LBS. 56 IN-LBS. 1033 LBS.

METALS


S U B STR ATE S

714 513 399 307 1068 - 514 - 1465 - -


METALS

PLYWOOD OSB HEMLOCK FIRSOUTHERN PINE SPRUCE PINE FIR

S U B STR ATE S

714 513 399 307 1068 - 514 - 1465 -

3/4 5/8 1/2 7/16 1" 1-1/2" 1" FULL 1" 1-1/2"PuLL OuTSTRENGTH

NOM. GAUGE

THICKNESS

#10

29

.015

690

26

.019

877


DESIGNATION

PuLL OVERSTRENGTH

NOM. GAUGE

THICKNESS

300ss TYPE A

29

.015

685

26

.019

869


DESIGNATION

PuLL OVERSTRENGTH



9

CLIPSCREWS + ULTRALO

Marco’s ClipScrews™ are designed to attach standing seam roof clips to plywood, OSB, or wood purlins.

ClipScrews are designed with a unique head style and configuration to provide superior hold. Material and plating options meet performance requirements to secure roof clips while providing long lasting quality. ClipScrews are engineered with an installation combo drive control for uniform installation performance.

ClipScrews™

ClipScrews™

SIZE HEAD STYLE CARTON QTY WEIGHT/M10 x 1"

10 x 1-1/2"

#2 Phillips Square Pancake

#2 Phillips Square Pancake

5000

2500

6.776

9.268

UltraLo is designed to attach standing seam roof clips to Plywood, OSB, or wood purlins.

This ultra thin wafer head is designed for standing seam panels that utilize no clip but require a thin head so as to not dimple the roof panel. This ultra low style head also provides exceptional pull over strength.

SIZE HEAD STYLE CARTON QTY WEIGHT/M10 x 1-1/8"

10 x 2

10 x 3

#2 Phillips Square Wafer



5000

2500

2000

6.776

9.268

6.141

10

STANDARD OPTIONAL

STANDARD OPTIONAL


MAJOR DIAMETER

MINOR DIAMETER

HEAD DIAMETER

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

28º TYPE 17


.194 / .188 .133 / .126 .44 2140 LBS. 60 IN-LBS. 1545 LBS.

MAJOR DIAMETER

MINOR DIAMETER

HEADDIAMETER

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

35º SHARP


.204 / .198 .128 / .122 .450 1920 LBS. 61 IN-LBS. 1633 LBS.

METALS


S U B STR ATE S

656 274 358 274 988 - 510 - - 771 -


METALS

PLYWOOD OSB HEMLOCK FIRSOUTHERN PINE SPRUCE PINE FIR

S U B STR ATE S

- - 358 274 898 - 431 - 538 -

3/4 5/8 1/2 7/16 1" 1-1/2" 1" FULL 1" 1-1/2"PuLL OuTSTRENGTH

NOM. GAUGE

THICKNESS

ClipScrew

29

.015

529

26

.019

778

24

.024

1128

22

.032

1512


DESIGNATION

PuLL OVERSTRENGTH

NOM. GAUGE

THICKNESS

UltraLo

29

.015

685

26

.019

-

24

.024

-

22

.032

-


DESIGNATION

PuLL OVERSTRENGTH



11

MAJOR DIAMETER

MINOR DIAMETER

HEAD DIAMETER

NOMINALTENSILE

MINIMuMTORSIONAL

NOMINALSHEAR

30º SHARP 1430º SHARP 17


.254 / .248 .185 / .178 .375 / .367 4281 LBS. 125 IN-LBS. 2999 LBS.

.280 / .273 .220 NOM .375 / .367 5167 LBS. 220 IN-LBS. 3957 LBS.

NOM. GAUGE

THICKNESS

#14/17 x 16mm(.062")

29

.015

559

26

.019

892

24

.024

1200

22

.032

1275

20

.038

1610

M ATE R I A LAZ55 GALVALUME G-90 GALVANIZED

DESIGNATION

PuLL OVERSTRENGTH

PLYWOOD OSB HRS PRIME ONLYYELLOW PINE SPRUCEHEMLOCK

S U B STR ATE S

845

-

650

-

379

-

295

-

747

-

1187

-

672

-

655

-

806

1411

1252

1432

2020

2150

3/4 5/8 1/2 7/16 1" 1-1/2" 1" 1-1/2" 16 / .065 14 / .07 12 / .106

PuLL OuTSTRENGTH

Metal2Wood-XD is available in three point styles – AB, B, and A.

AB B A

#14

#17

12

Marco offers a full range of carbon steel and stainless steel self-tapping screws. Available to meet all your fastener requirements for wood and light gauge metal with a pre-drilled hole.

SIZE HEAD STYLE CARTON QTY WEIGHT/M14 x 3/4"

14 x 1"

14 x 1-1/4"

14 x 1-1/2"

14 x 2"

14 x 2-1/2"

14 x 3"

1/4 x 3/4" – AB

17 x 3/4" – AB

17 x 1" – AB

17 x 1-1/4" – AB

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

3/8" HWH

2000

2000

2000

1500

1000

1000

1000

2000

2000

2000

2000

12.62

16.91

17.63

24.60

26.02

30.80

35.91

12.62

14.02

18.00

22.03

STANDARD OPTIONAL


METAL2WOOD-XD + FASTENER SELECTION

.190"

.210"

.250"

.250"

Drill bit sizes are for new construction applications



Requires 600-800 rpm screw gun

SIZE INCHES NOTES#10

#12

#14

#14 304 SS

.210"

.240"





1/4"

1/4” 304 SS

.210"

.240"

.285"



Repair screw for stripped 1/4" 11 ga. steel


Requires 600-800 rpm screw gun / Repair screw for stripped 1/4" 11 ga. steel


1/4"

#17

1/4" 304 SS

#17 304 SS

All screws listed other than 304 Stainless Steel are carbon steel with zinc plating.

NOMINAL DIAMETER & ALLOY

STEEL PANEL OR STRUCTURAL THICKNESS

POINT TYPE

A

AB

B

#10

#12

#14

#14 SS

.010

.020

.030

.040

.050

.060

.070

.080

.090

.100

.110

.120

.130

.140

.150

.160

.170

.180

1/8"

9/64"

3/16"

3/16"

9/64"

9/64"

#8

#81/8"

#12

1/4"

#17

1/4” SS

#17 SS

.010

.020

.030

.040

.050

.060

.070

.080

.090

.100

.110

.120

.130

.140

.150

.160

.170

.180

1/8"

1/8"

9/64" 11/64"

#7

#7

#1

#1

17/64"

17/64"

#8

#81/8" 3/16"

1/4"

1/4"

3/16"

3/16"

#12

1/4"

1/4" SS

.010

.020

.030

.040

.050

.060

.070

.080

.090

.100

.110

.120

.130

.140

.150

.160

.170

.180

11/64"

#7

#7

3/16"

#1

#1

#8

#8

FastenerSelection



13

14

PLATING + COATING + TERMS

PlatingOptions

CoatingOptionsTRIPLEGUARD

Extend the life of your fasteners by choosing Marco TripleGuard. This fastener coating combines an electroplated zinc and chromate substrate with an organic topcoat. The electroplated zinc layer provides sacrificial protection of the steel substrate while the topcoat creates a durable barrier.

TripleGuard is engineered to provide extended field life

and improve the mechanical performance of fasteners. It is also engineered with integrated friction modifiers to eliminate the need for sealers or post-coating lubricants.

TripleGuard provides superior product performance in fewer layers than comparable finishes. Fewer processing steps result in improved quality and reduced cost.

The one coating with three times the protection.

Standard mechanical plating

Marco’s standard plating is 1 mil of mechanical plating. This provides all our fasteners with maximum plating protection.

Salt spray tests for our standard SureShield plated fasteners exceed 1,000 salt spray hours. Our mechanical plating eliminates all hydrogen embrittlement.

MARCO’S FASTENER SALT SPRAY TEST RESULTS AVAILABLE UPON REQUEST.

MARCO’S FASTENER SALT SPRAY TEST RESULTS AVAILABLE UPON REQUEST.

Marco uses .005 electroplating for all fasteners, with the option to add additional coatings as well. This provides excellent salt spray and Kesternich ratings. Electroplating also provides good lubricity and wear resistance for both the QuikGrip and QuikDrill fastener families.

SURESHIELD

Marco’s electroplating technology.

ELECTROPLATE

15

FastenerTerms



TENSIONSTRENGTHThe point at which a fastener fails under a load exerted in two direct and opposite directions.

Fastener tension is created when a fastener elongates

during tightening, producing the clamp load that prevents movement between joint members. Such movement is arguably the most common cause of structural joint failures.

TORSIONSTRENGTHWith Torsion testing, we are able to simulate real life service conditions, check product quality, and ensure proper manufacturing techniques. Torsion tests are performed by applying rotational forces or by applying

both compression and rotational forces. Types of torsion testing vary from product to product but can usually be classified as failure, proof, or product operation testing.

SHEARSTRENGTHShear is accomplished by exerting shear force (pressure) in the crosswise surface of the fastener until shear failure occurs.

Shear force causes the two adjacent portions of the fastener to slide in opposite directions parallel to their contact surface.

PULLOUTPERFORMANCEPullout is the capacity of a fastener’s thread connection with a particular medium to remain intact and resist being pulled out of the medium.

PULLOVERPERFORMANCEPullover performance relates to the capacity of a fastener to resist the pulling of the fastened sheet material over the head of the fastener.

The resistance to pullover is related to the strength and diameter of the fastener washer as well as the strength and thickness of the metal panel used.

CORPORATE 9410 E. 54th Street | Tulsa, OK 74145 | 1.800.800.8590 | Fax: 1.918.622.4536CANADA 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | Fax: 1.306.775.0072

Remove the re-roofing danger, expense, and hassle of wood firring with RE2.TM

• Eliminate tear-off

• Easy to install

• No more warped wood firring

• Cost comparable to wood, plus increases profitability

• Won’t rot, corrode, or crease metal

Re-roof with RE2™

Use RE2 instead of wood spacers and you’ll solve the re-roofing problems.

The revolutionary RE2 is manufactured with high density polyethylene foam. It’s lightweight, yet strong and won’t rot or corrode the metal roof you install on top of it, nor will it warp which causes the metal to crease.

RE2 is sold in two150-foot easy-to-handle rolls. You just roll it across the old shingled roof, tack it down (with the 50 nails included), and install the metal roof on top. RE2 acts as a spacer between the old shingles and the new metal roof, providing air flow and ventilation.

The initial cost of RE2 is comparable to using wood spacers. Yet, it’s easy to handle and easy to install (heavy tools not required!), so it increases productivity.

Since RE2 won’t warp like wood, you’ll experience fewer customer callbacks. And our own customers report that insurance risks are even reduced with RE2.

Foam Spacer System

Typical Physical Properties



Physical Property Test Method ValueCompressive Strength ASTM D3575-00 3.8 -Vertical direction (psi) Compression Set (%) ASTM D3575-00 < 30Tensile Strength (psi) ASTM D3575-00 58 suffix T (md / cmd) 30Elongation ASTM D3575-00 86 suffix T (md / cmd) 60Tear Resistance (lb/in) ASTM D3575-00 11 suffix G (md / cmd) 17Density Range (lb/ft2) ASTM D3575-00 1.5–1.9Water Absorption (lb/ft2) ASTM D3575-00 < 0.1 suffix LThermal Stability ASTM D3575-00 < 5% suffix SContact Corrosivity Method 3005 FED None (Alum. Plate) STD. 101Static Decay EIA STD. 541 < 2 sec. (anti-static grade) Appendix FSurface Resistivity EIA STD. 541 1.0 x 10^9 – (anti-static grade) section 4.3 1.0 x 10^12Thermal Conductivity k-value ASTM C518-91 0.35–0.42 (BTU-IN / HR-FT2-°F)Thermal Resistance R – Value ASTM C518-91 1.30–1.60 (HR-FT2-°F / BTU


RE2™ represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0311

anglekut™

anglekut™


roof boots™

x-seal™

Mastix™

CloSuRE FoaM™

lp2™

Fastenersflex-o-vent™

Clip sCrews

Clips

MaRCo WEaThER-TiTE SySTEM™

Revolutionary spacer system uniquely designed for metal roofing.

Typical application

Fast and Easy Installation

Provides ventilation

RE2™

The Marco Pipe Flashing System

RoofBoots™

• Easy, on-site customization

• Maximum resistance to ozone/ultraviolet weathering

• Flexible base forms seal with most panels

• EPDM or Silicone sleeve accommodates expansion/contraction

• Lots of sizes and color choices

• 20-year warranty

• 35-year warranty available

RoofBoots™ are made with

clearly marked sleeves which can

be cut on-site to easily customize and precisely fit the pipe

diameter you need. The sleeves come in EPDM 500 and Silicone—designed for the maximum resistance to weathering due to ozone and ultraviolet light.

The base on RoofBoots™ is flexible and designed to form a seal on all types of roofing surfaces (including metal, plastic, tile,

and more), and on almost any panel configuration and roof pitch, regardless of the pipe location.

So installation is simple: choose the pipe opening and trim the sleeve, slide the boot over the pipe, form to the roof profile, apply sealant, and fasten to complete the installation.

You can also choose from round or square base, from Marco’s full selection of

wraparound retrofit and solar boots, many sizes, and several color

choices.

High temperature RoofBoot shown here

20yEar waRRanty

™

Customizable, flexible sleeves that form a seal around pipes on all roofing surfaces

™

3 4

21

5

Step-by-step installation

Choose the pipe opening and trim the sleeve

Apply sealant

Slide the boot over the pipe and form to the roof profile

Fasten to roof

Installation complete

Dark Blue

Terra Cotta

Gray

Dark Green

Light Green

Bright Red

Black

Light Blue

White

Brown

Squa

reRo

und

2.77" - 75.25"[See chart on following page for specific size

information and availability]

2.77" - 75.25"[See chart on following page for specific size

information and availability]

9 sizes / 10 colors

Specification Data EPDM 500 SILICONEADVANCED OZONE RESISTANCE tested 70 hours @ 500 pphm 70 hours @ 500 pphm HIGH TEMPERATURE RESISTANCETested to: intermittent +100°C (+275°F) +135°C (+275°F)Tested to: continuous +225°C (+437°F) +260°C (+500°F) Solar: Tested to: intermittent +135°C (+275°F) +260°C (+500°F) Solar: Tested to: continuous +100°C (+212°F) +225°C (+437°F) LOW TEMPERATURE RESISTANCE tested -55°C (-65°F) -74°C (-100°F) Solar Low Temp -50°C (-67°F) -74°C (-101°F)TENSILE SET maximum 10 MPa (1450 psi) 5 MP1 (700 psi)COMPRESSION SET maximum 25% 50%

Complete specification data and testing methods are available upon request.

EDPM / Silicone CompoundsAs part of a standard classification system for rubber products these general specifications present conservation engineering minimums which should be used for design criteria.

General recommendations must be tested for extreme applications.

edpm RoofBoots™ engineeRing specificationsAstm d2000 m3 bA 510 A1 b13 c12 f17 z1 z2 z3 z4 z5 z6 z7

gRade 3

type b General tes temp 100°cclass A Volume swell no req5 50 durometer (range)10 tensile 10 mpa (approx. 1450 psi)A14 Heat Aging 70 hrs @ 100°cb13 compression set 22 hrs @ 70°c max 25% Astm d395bc12 Ozone Resistance 70 hrs @ 50pphm Astm d1171 100% Quality Retentionf17 Low temperature brittleness 3 min @ -40°c pass Astm d2137 A, 9, 3, 2z1 55 durometer (specific target)z2 epdm (specific elastomer)z3 Horizontal flame Resistance, uL 94 Not to exceed 3"/minz4 Ozone Resistance Advanced Requirementz5 70 hrs @ 500pphm @ 100°f Accelerated Weathering Resistancez6 (u.V. Light), Astm G-53z7 tear Resistance, Astm d-624, die “d” Resistance to discoloration, Astm

silicone RoofBoots™ engineeRingAstm d2000 m4 Ge 505 A19 b37 c12 f19 G11 z1 z2 z3 z4

gRade 4

type G General tes temp 225°ccLAss e Volume swell max 80%5 50 durometer (range)05 tensile 5 mpa (minimum 725 psi)A19 Heat Aging 70 hrs @ 225°c change in Hardness max +10 pts change in tensile max -30% change in ultimate elongation max -30%b37 compression set 22 hrs @ 175°c max 50% Astm d395bc12 Ozone Resistance 70 hrs @ 50pphm Astm d1171f19 Low temperature brittleness 3 min @ -55°c pass Astm d2137 A, 9, 3, 2G11 tear Resistance, Astm d-624, die “b”z1 55 durometer (specific target)z2 silicone (specific elastomer)z3 Horizontal flame Resistance, uL 94 not to exceed 3"/minz4 Ozone Resistance Advanced Requirement 70 hrs @ 500pphm @ 100°f

pipe Range compound paRt # flashing details

#1 1/4"–2 1/2" Black EPDM RD101BE A Top opening diameter Closed (6.35–63.5) Grey EPDM RD101GG B Overall height 2.77" (70.4 mm) Red Silicone RD101RG C Base diameter 4.75" (120.7mm)

#2 1 3/4"–3" Black EPDM RD201BE A Top opening diameter 1.44" (36.6 mm) (44.5–76.2 mm) Grey EPDM RD201GG B Overall height 3.35" (89.7 mm) Red Silicone RD202RG C Base diameter 6.21" (157.7 mm)

#3 1/4"–5" Black EPDM RD301BE A Top opening diameter Closed (6.35–127 mm) Grey EPDM RD301GG B Overall height 3.64" (92.5 mm) Red Silicone RD302RG C Base diameter 7.74" (196.6 mm)

#4 3"–6 1/4" Black EPDM RD401BE A Top opening diameter 2.38" (60.5 mm) (76.2–158.8 mm) Grey EPDM RD401GG B Overall height 5.05" (128.3 mm) Red Silicone RD402RG C Base diameter 9.26" (235.2 mm)

#5 4 1/4–7 3/4" Black EPDM RD501BE A Top opening diameter 3.50" (88.9 mm) (108–196.9 mm) Grey EPDM RD501GG B Overall height 4.43" (112.5 mm) Red Silicone RD502RG C Base diameter 10.75" (273.1.7 mm)

#6 5"–9" Black EPDM RD601BE A Top opening diameter 4.25" (108 mm) (127–228.6 mm) Grey EPDM RD601GG B Overall height 5.60" (142.2 mm) Red Silicone RD602RG C Base diameter 12.50" (317.5 mm)

#7 6"–11" Black EPDM RD701BE A Top opening diameter 4.90" (124.5 mm) (152.4–279.4 mm) Grey EPDM RD701GG B Overall height 5.84" (148.3 mm) Red Silicone RD702RG C Base diameter 14.60" (370.8 mm)




Min. 1/8"–3/4" Black EPDM SQ051BA A Top opening diameter 1/16" (3–20 mm) B Cut to suit pipe size 1/8"–3/4" C Base diameter 2 1/4"

#1 1/4"–2" Black EPDM SQ101BA A Top opening diameter Closed (6–50 mm) Grey EPDM SQ101GA B Cut to suit pipe size 1/4"–2" Red Silicone SQ101RA C Base diameter 4 1/4"

#2 1 1/4"–3" Black EPDM SQ201BA A Top opening diameter 7/8" (32–76 mm) Grey EPDM SQ201GA B Cut to suit pipe size 1 1/4"–3" Red Silicone SQ202RA C Base diameter 6"

#3 1/4"–4" Black EPDM SQ301BA A Top opening diameter Closed (6–102 mm) Grey EPDM SQ301GA B Cut to suit pipe size 1/4–4" Red Silicone SQ302RA C Base diameter 8"

#4 3"–6" Black EPDM SQ401BA A Top opening diameter 2 1/2" (76–152 mm) Grey EPDM SQ401GA B Cut to suit pipe size 3"–6" Red Silicone SQ402RA C Base diameter 10"


#6 5"–9" Black EPDM SQ601BA A Top opening diameter 4" (127–228 mm) Grey EPDM SQ601GA B Cut to suit pipe size 5"–9" Red Silicone SQ602RA C Base diameter 12"

#7 6"–11" Black EPDM RD701BE A Top opening diameter 5" (152–280 mm) Grey EPDM RD701GG B Cut to suit pipe size 6"–11" Red Silicone RD702RG C Base diameter 14"

#8 7"–13" Black EPDM SQ801BA A Top opening diameter 6" (178–330 mm) Grey EPDM SQ801GA B Cut to suit pipe size 7"–13" Red Silicone SQ802RA C Base diameter 17"


Max. 13"–26" Black EPDM SQ951BA A Top opening diameter 11" (330–660 mm) Grey EPDM SQ951GA B Cut to suit pipe size 13"–26" Red Silicone SQ952RA C Base diameter 34"

Sizing Chart Check diameter of pipe. Select the appropriate RoofBooTS™ product for pipe or duct diameter. For extreme pitch or surface irregularity select next larger size. Choose the compound required, then refer to the part number for the RoofBooTS™ product desired.

Steep Slope

Specifically designed for the metal roof industry, for applications with a 35 to 65 degree angle, while accepting and responding to the most commonly encountered pipe penetrations.

The built in 40° pitch allow the Extreme Angle Master Flash to handle any extreme roof pitch, sleeve flexibility accommodates vibration and pipe movement caused by expansion and contraction. Easy on site customization handles all normal installations, too. Fast, one piece construction allows for easy on-site installation in usually 5 minutes.

Made of EPDM or Silicone, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light. The soft aluminum base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

Steep Slope’s flexible design meets virtually all roofing needs. Sleeve flexibility accommodates vibration and pipe movement caused by expansion/contraction. Steep Slope was used to create a new engineering standard for profiled roofing by the International Association of Plumbing and mechanical Officials (for the uniform Plumbing Code) and remains the only product listed. These products are also listed for use with Type B vents. The addition of fire retarding agents milled directly into the rubber compound created a self extinguishing feature which enables it to be used with Type B vents. Listed with IAPMO certification No. 3121.


1/4" - 5 3/4" Black EPDM MFEA101BA A Top opening diameter Closed B Cut to suit pipe size 1/4" - 5 3/4" (6 - 146mm) Red Silicone MFEAS102RA C Base diameter 11" (279mm)

Made of EPDM or Silicone, these standard solar flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light. A C-12 ASTM additional requirement was added to assure conformance to the most stringent ozone/weathering specifications available.

With a pre-cut hole for pipe sizes 3/4" to 1" inch allowing minimal on-site preparation and assembly.The base is designed to form a seal on most panel configurations and roof pitch regardless of pipe location. The pitch canal allows for maximum flexibility, easily accommodating up to a 60 degree pitch without affecting the performance.

Multiport is specifically designed for Solar and Electrical Applications5 Port Design - One Design, Multiple Functions

Accommodates: 4-1/2” (114mm) BaseOne 0" - 1-15/16" - (0 - 49mm) Pipe Up to 4 cables or wires per flashingTwo 3/8" (0.9525mm) pipe / cable Extra ports accommodate copper pipe/electrical cablingTwo 3/4" (20mm) pipe / cable Easy install for solar applications

pipe compound paRt # flashing details

3/4"–1" Black EPDM MFSL A Top opening diameter 3/4" - 1" (19 - 25mm) B Overall height 2 1/2" (63mm)3/4"–1" Red Silicone MFSLS C Base diameter 4" (101mm)

pipe compound paRt # flashing details

0"-1 5/16" Black EPDM MFMP A Top opening diameter 0" - 1 5/16" (0 - 49mm) B Overall height 2 1/2" (63.5mm) Red Silicone MFMPS C Base diameter 4 1/2" (114mm)

Solar – Standard / Multiport

STEEP SLoPE

STEEP SLoPE

SoLar / MULTIPorT

titebond® Roof sealant is specifically formulated to outperform all other sealant technologies, including silicones, tri-polymers, and polyurethanes. this superior polymer formula provides a waterproof seal against water, wind, dust and dirt. It offers exceptional adhesion to Kynar™ coated metal surfaces, plastics and glass. the product is ideal for use on a wide variety of metal roof, trim, architectural metal siding, aluminum, galvanized steel, galvanized gutters, flashing and downspouts. It also provides unbeatable adhesion to wood, brass and other common building substrates.

A trimmable joint and end lap sealing tape for metal roofing and wall jobs. Mastix is a high quality adhesive on a roll...the roll won’t telescope from heat before installation, and Mastix really holds hot metals. It’s made with a superior adhesive that’s non-staining and permanently flexible. Use it to provide an excellent seal around windows, doors, roof vents, stacks, access doors, and other penetration points... wherever you need to seal metal to metal.

Quikdrill metal-to-metal fasteners and QuikGrip metal-to-wood fasteners are the bedrock of the marco Weather-tite system. Quikdrill and QuikGrip offers you the right fastener for all pre-engineered metal building applications – any job, any size, any conditions, any environment.

both fastener families feature fasteners with a higher crown to allow a better, tighter socket fit, and cupped head and HWH for improved pullover strength. mechanical plating is standard with most fasteners, with stainless steel and zinc also available. No matter what your application or environment, there’s a coating that’s right for you. Whether it’s the matchtech painted coating or tripleGuard corrosion protection, marco has your fasteners covered from start to finish.

Ordering RoofBoots? For easy installation, don’t forget to order...

The Expanding Marco Weather-Tite System™

For nearly twenty years, Marco Industries™ has been delivering award-winning products to the metal building industry that offer easy installation, remarkable building ventilation, lower utility costs, extreme durability, and outstanding warranties...products that are economically and ecologically smart. Choose Marco for Everything you need to Make your Structure weather-tite.™

angLEkUT™


M-CLIPS™

Many clips and fastenersfrom which to choose

TITEbonD SEaLanTDurable & flexible

x-SEaL™ Expandable Foam tape

MaSTIx™

Butyl tape

WEaThEr-TITE DoorS™


CLoSUrE FoaM™


rooF booTS™

Pipe Flashing

rE2™

non-warping, non-Corroding Reroof Retrofit Spacer

SILL-rITEMulti-use sill plate sealer provides a long-lasting seal

LP2™


QUIkgrIP™

Metal to wood fastener

FLEx-o-vEnT™


QUIkDrILL™

Metal to metal fastener


Marco Industries Corporate: 9410 E. 54th Street | Tulsa, oK 74145 | 1.800.800.8590 | fax: 1.918.622.4536

Marco Industries Canada: 1632 Broder Street | Regina, Sask S4N 7K1 | 1.866.244.7573 | fax: 1.306.775.0072041

RoofBoots™ represent yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MADE IN USA

Made withRecycled MateRial

The Rite way

Sill-Rite sill plate sealer is made from lightweight polyethylene foam. By filling the gap between the sill plate and the foundation, air infiltration is considerably reduced to provide cost savings for your heating and air conditioning.

Worried about sill plate rot? Marco’s got you covered. Sill-Rite’s durable, moisture resistant characteristics help prevent water and insect infiltration.

Unroll Sill-Rite flush to the top of the foundation wall and staple to bottom of sill plate or tilt-up-wall section. Fit Sill-Rite over anchor bolts. Position sill plate flush with the foundation and secure with anchors. It’s that easy.

Marco’s multi-use sill plate sealer provides a long-lasting seal for almost any construction project

Keep air, moisture, and insects out

Seal your sill plate

• Fills any irregularities between sill plate and top of foundation wall to help reduce air penetration

• Easy to install – No need for extra tools

• Resists moisture infiltration to the structure’s interior

• Helps keep insects out

• Available in convenient 50' rolls

• Saves on heating and cooling costs by eliminating drafts around the sill

• Can be used as an expansion joint in concrete and masonry construction

• Can be used in installation around window

and door frame openings or around building sections or panels



To place your order: 1.800.800.8590 | marcoindustries.com | [email protected]

Sill-Rite represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0411

Step 1Unroll flush to top of foundation wall and staple to bottom of the sill plate or tilt-up-wall section.

Step 2Fit Sill-Rite over anchor bolts.

Step 3Position sill plate flush with the foundation and secure with anchors.

Materialthickness

ribheight

rib spacing

MaterialDensity

Materialcolor

Materialtype

roll DiaMeter

ValUe astM 5-1/2" x 50'

3-1/2" x 50'

5-1/2" x 50'

DensitycoMpression recoVery

coMpression DeFlectiontensile strength

Water absorptionr-ValUe

teMperatUre liMitsealant Use

3-1/2" x 50'

S i ll- r ite5 0 ' r o llS

P r o D U Ct te Sti N G

1/4" 1/16" 1-1/16" 22kg/m3 ± 10% Beige Polyethylene 17"

2.0 lb/ft3 avg.

>90%, min.

21 psi

55 psi, min.

<4% max

3.0

-40º to 160ºF

Cold and hot applied

D1622

D5249

D5249

D1623

D3575

n/a

n/a

C1330 Type 2, Type C

1/4" 1/16" 27/32" 22kg/m3 ± 10% Beige Polyethylene 17"

Many other uses.Use as an expansion joint in masonry and concrete construction projects • Flexible gasket for building section or panels • Sealing cracks and crevices under siding • Window and door frame opening sealer • Protective wrap for pipes

1/16"

1/16"

1-1/16"

27/32"

1/4"

1/4"

5-1/2"

3-1/2"

anglekut™


anglekut™


Weather-tite™ Sealant/adheSiveStays put...during installation and after

roof bootS™ Pipe Flashing

x-Seal™ Expandable Foam Tape

MaStix™

Butyl Tape

Weather-tite doorS™


cloSure foaM™


re2™

Non-Warping, Non-Corroding Reroof Retrofit Spacer

lp2™


faStenerSChoose from hundreds of standard and low profile fasteners

flex-o-vent™


SySteM approaching

Marco’S Weather-tite SySteM™ Will prepare you for any SySteM.

W e a t h e r . P r o o f .For twenty years, Marco Industries™ has been delivering award-winning products to the building industry. Products that offer easy installation, remarkable building ventilation, lower utility costs, extreme durability, and outstanding warranties. Products that are economically and ecologically smart. Products that constitute the basis of the Marco Weather-Tite System®. But a system of even the very best products isn’t complete or effective without a proven record of getting those products into the hands of customers fast.

So the Weather-Tite System® includes a commitment by Marco of rapid response to your order. Marco is the only industry leader who promises and consistently delivers customer service at that level. Choose one Marco product, place your order and discover that it truly provides the industry standard in performance and reliability, time after time, through all kinds of weather, and it will be the proof you need to come back for all the other Marco products in the entire Marco Weather-Tite System™.

the forecaSt alWayS lookS good With the Marco Weather-tite SySteM™



flex-o-vent™

Flexible Foam Ridge Vent as universal ridge vent Helps prevent rain/snow infiltration which can block ventilation. Extremely durable polyester is flame-, clog-, tear-resistant and economical. Double bead of M63 adhesive makes it easy to install. It’s economical and comes with a 40-year limited warranty.

lp2™

Low Profile Vented Closure as ridge vent Made from re-cycled polyester, LP2 is non-woven, non-wicking. Special contours provide custom, low-profile fit for any pitch and most major roof profiles to help keep out dust, moisture, insects, and yet allow ventilation to reduce utility costs.

anglekut™

Custom Beveled Inside/Outside ClosureEasy-to-order for a precisely matched profile/angle to every hip and valley on metal roof panel. Easy to install for a superior seal, plus it won’t bleed, dry out, or dissolve when subjected to weather and UV rays.

Weather-tite™ Sealant/adheSiveStays put...during installation and afterFeatures low VOC, excellent flexibility, a fast cure...paintable and mold/mildew resistant. And is extremely easy to install.

re2™

Non-Warping, Non-CorrodingReroof Retrofit SpacerNo more warped wood firring! Eliminate tear-off with the easy-to-install RE2™ which won’t rot, corrode, or crease metal.

Weather-tite doorS™

Rolled Edge, Reliable Seal (5 models)Special rolled edge, dual contact weather-strip designed into the frame creates a uniquely strong seal. All models (except the extremely economical aluminum mill frame) come with all steel frame and skin. Several add-on options available.

cloSure foaM™

Inside/Outside Closures with adhesiveChoose profiles for every application, 5 different foams, and thickness variety. Provides better UV resistance. A full ¼" adhesive bead means non-blow-away installation, even in subfreezing temperatures or wet surfaces.

MaStix™

Butyl TapeThis trimmable, non-staining, and permanently flexible joint and end lap sealing tape is for sealing around windows, doors, roof vents stacks, access doors, and other penetration points. The high-quality adhesive prevents “telescoping” from heat during installation and keeps the tape in place on hot metal roof and wall panels.

roof bootS™ Pipe FlashingChoose round base, square base, retro-fit, silicone...and several colors. All Roof Boot sizes (to fit 1/4" to 9" pipe) provide a flexible, durable, secure fit.

x-Seal™ Expandable Foam TapeX-Seal™ expands from ¼" to 1-1/4", flexes, and compresses to fit any troublesome gap, providing an economical and UV-stable way to keep out bugs and vermin and to maintain a seal in heat or cold. Won’t dry out or extrude like caulk or butyl tapes.

faStenerSChoose from hundreds of standard and low profile fasteners

MPC0910


These products and more represent Marco Industries’ technological development in bringing you innovative, higher quality, and more economical products for the building industry.

Fill gaps with X-Seal.• Expands from ¼" to 1-¼"• Follows, flexes, expands, compresses to fit• UV stable• Won’t dry out or extrude like caulk or butyl tapes• Highly resistant to bugs and vermin• Economical• Maintains seal in heat and cold

For any shaped gap in the construction of metal buildings, doors and windows, concrete, wood, and more…

X-Seal comes compressed at just one-quarter inch, on an easy-to-handle roll. Cut the desired length of X-Seal, place X-Seal into the gap opening—even one with irregular hips and valleys—and remove the protective release paper. Now watch X-Seal slowly expand up to 1-1/4" to completely fill and seal the gap.

X-Seal won’t dry out and become hard or brittle. And it’s highly resistant to bugs and vermin.

It’s UV stable and maintains a seal during thermal expansion and

contraction of building panels. It has excellent compressibility and recovery

(for minimal compression set). It’s a very good thermal and sound insulator. And

there’s no shrinkage or blow-out from closed-cell breakage with X-Seal.

X-Seal holds the exterior out and the interior in, yet allows vapors to move through. A hermetic seal allows the absorption of moisture and when conditions permit, the slow release of moisture through evaporation.

With features like those, X-Seal’s versatility makes it perfect for sealing gaps in so many construction projects, between similiar and dissimiliar materials:

• Joints and seams in metal construction• Around doors and windows• For control joints, expansion joints and isolation

joints in concrete construction• Civil and underground construction (highway and

airport runways)• Log and prefabricated homes• Panel joints in precast panel construction

E x p a n d a b l e F o a m T a p e

Expandable Foam Tape

Expandable foam tape.

Physical Characteristics



1.800.800.8590 | MarcoIndustries.com | [email protected]

X-Seal™ represents yet another Marco Industries technological development in bringing you innovative, higher quality, and more economical products for the building industry.

MPC0311

anglekut™

anglekut™


roof boots™

Mastix™

FlEX-o-VEnT™

re2™

lp2™

Fasteners

Clip sCrews

Clips ClosureFoam™

Marco WEaTHEr-TiTE SySTEM™

Doors ExpandedHips Previous to Expansion

X-SEal™

Description/Base/Color:.............................. Precompressed,.self-expanding.pur-foam.impregnated.with.a.high.quality.modified.acrylic,.. flame.retardant.emulsion...The.base.foam.is.black;.other.colors.available.Density:........................................................ 10.lbs./cu..Ft...150.kg/m3Flammability:............................................... UL.94.HF1,.Self-Extinguishing,.DIN.4102,.B1.compression.at.50%,.B2.compressedTemperature.Stability.Range:....................... -40˚F.to.212˚FManufacturer’s.Lab:...................................... (-40˚C.to.120˚C)Weather.Resistancy:..................................... ExcellentCompression.Set:........................................ Maximum.2%Tensile.Strength:.......................................... 21.8.psiThermal.Conductivity:.................................. 12,106.BTU.(hr.).(ft2).(*F/ft)

Documents

Marco Full Product Catalog