Manual Placa Base Ga-946gm-Ds2 (s2) e

GA-946GM-DS2/S2 (rev. 2.0)Intel CoreTM 2 Extreme quad-core / CoreTM 2 Quad /Intel CoreTM 2 Extreme dual-core / CoreTM 2 Duo /Intel Pentium Processor Extreme Edition /Intel Pentium D / Pentium 4 LGA775 Processor Motherboard

User's ManualRev. 200212ME-946GMDR-2002R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household wasteand must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

Motherboard

GA

-946GM

-DS2/

GA

-946GM

-S2 (rev. 2.0)

Oct. 20, 2006

Oct. 20, 2006

Motherboard

GA-946GM-DS2/GA-946GM

-S2 (rev. 2.0)

Copyright 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.The trademarks mentioned in the manual are legally registered to their respective companies.

NoticeThe written content provided with this product is the property of Gigabyte.No part of this manual may be reproduced, copied, translated, or transmitted in any form or by anymeans without Gigabyte's prior written permission. Specifications and features are subject tochange without prior notice.

Product Manual ClassificationIn order to assist in the use of this product, Gigabyte has categorized the user manual in thefollowing:

For detailed product information and specifications, please carefully read the "Product User Manual".

For detailed information related to Gigabyte's unique features, please go to "TechnologyGuide" section on Gigabyte's website to read or download the information you need.

For more product details, please click onto Gigabyte's website at www.gigabyte.com.tw

- 4 -

Table of Contents

Item Checklist ................................................................................................................. 6Optional Accessories ...................................................................................................... 6GA-946GM-DS2/GA-946GM-S2 (rev. 2.0) Motherboard Layout ................................... 7Block Diagram ................................................................................................................ 8

Chapter 1 Hardware Installation ..................................................................................... 91-1 Considerations Prior to Installation .................................................................... 91-2 Feature Summary .......................................................................................... 101-3 Installation of the CPU and CPU Cooler ....................................................... 12

1-3-1 Installation of the CPU ......................................................................................... 121-3-2 Installation of the CPU Cooler ............................................................................ 13

1-4 Installation of Memory .................................................................................... 141-5 Installation of Expansion Cards ...................................................................... 161-6 I/O Back Panel Introduction ........................................................................... 171-7 Connectors Introduction .................................................................................. 18

Chapter 2 BIOS Setup ................................................................................................ 29The Main Menu (For example: BIOS Ver. : GA-946GM-DS2 F1a) .......................... 302-1 Standard CMOS Features ............................................................................. 322-2 Advanced BIOS Features .............................................................................. 342-3 Integrated Peripherals ..................................................................................... 362-4 Power Management Setup ............................................................................. 392-5 PnP/PCI Configurations ................................................................................. 412-6 PC Health Status ........................................................................................... 422-7 Frequency/Voltage Control ............................................................................. 442-8 Load Fail-Safe Defaults ................................................................................... 452-9 Load Optimized Defaults ................................................................................. 452-10 Set Supervisor/User Password ..................................................................... 462-11 Save & Exit Setup ......................................................................................... 472-12 Exit Without Saving ....................................................................................... 47

- 5 -

Chapter 3 Install Drivers ............................................................................................. 493-1 Install Chipset Drivers .................................................................................... 493-2 Software Applications ..................................................................................... 503-3 Driver CD Information .................................................................................... 503-4 Hardware Information ..................................................................................... 513-5 Contact Us ..................................................................................................... 51

Chapter 4 Appendix ................................................................................................... 534-1 Unique Software Utilities ................................................................................ 53

4-1-1 EasyTune 5 Introduction ..................................................................................... 534-1-2 Xpress Recovery2 Introduction ......................................................................... 544-1-3 Flash BIOS Method Introduction ........................................................................ 564-1-4 2- / 4- / 6- / 8- Channel Audio Function Introduction ...................................... 65

4-2 Troubleshooting ............................................................................................... 70

- 6 -

Item ChecklistIDE Cable x 1 and FDD Cable x 1SATA 3Gb/s Cable x 2I/O Shield

* The items listed above are for reference only, and are subject to change without notice.

Optional Accessories 2 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-51/R) 4 Ports USB 2.0 Cable (Part Number: 12CR1-1UB030-21/R) SPDIF In and Out Cable (Part Number: 12CR1-1SPINO-11/R) COM Port Cable (Part Number: 12CF1-1CM001-31/12CF1-1CM001-12R) e-SATA Cable (Part Number: 12CF1-3SATPW-11R)

- 7 -

GA-946GM-DS2/GA-946GM-S2 (rev. 2.0) Motherboard Layout

KB_MS CPU_FAN

LGA775

ATXGA

-946

GM-D

S2/G

A-94

6GM-

S2

USB

LAN

F_AU

DIO

AUDIO

BIOS

PCIE_16 IDE

PCIE_1CD_IN

CI

DDRI

I3DD

RII4

F_USB2

BATTERY

F_PANEL

IT87

18ATX_12V

Intel 946GZ

Intel ICH7

PWR_LED

FDD COMB

PCI1

PCI2

USB

CLR_CMOS

COMA

LPT

CODEC

RTL8111B

SPDIF_IO

SYS_FAN

F_USB1

VGA

SATAII3SATAII2

SATAII1SATAII0

DDRI

I1DD

RII2

REV: 2.0

- 8 -

Block Diagram

(Note) To use a DDRII 667 memory module on the motherboard, you must install a 1066/800 MHzFSB processor.

Cent

er/S

ubwo

ofer

Spe

aker

Out

Line-

Out

MIC

CPU CLK+/-(133/200/266 MHz)

PCI Express x16

HostInterface

DDRII 667(Note)/533 MHz DIMM

IT8718

Line-

In

2 PCI

PCI Bus

SPDI

F In

SPDI

F Ou

t

8 USBPorts

Dual Channel Memory

Side

Spe

aker

Out

Surro

und

Spea

ker O

ut

LAN

PCI CLK (33 MHz)

CODEC

PCIe CLK(100 MHz)

Intel946GZ

IntelICH7

LGA775Processor

4 SATA 3Gb/s

ATA 33/66/100IDE Channel

BIOS

PS/2 KB/Mouse

VGA

COM Ports

LPT Port

Floppy1 PCI Express x1

PCI Express Bus

PCIe CLK(100 MHz)

RTL8111B

RJ45

x 1 x 1

Hardware Installation- 9 -

English1-1 Considerations Prior to InstallationPreparing Your ComputerThe motherboard contains numerous delicate electronic circuits and components which canbecome damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, pleasefollow the instructions below:1. Please turn off the computer and unplug its power cord.2. When handling the motherboard, avoid touching any metal leads or connectors.3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.5. Please verify that the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are required

for warranty validation.2. Prior to the installation of the motherboard or any hardware, please first carefully read the information

in the provided manual.3. Before using the product, please verify that all cables and power connectors are connected.4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.5. Please make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.6. Please do not place the computer system on an uneven surface.7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty1. Damage due to natural disaster, accident or human cause.2. Damage as a result of violating the conditions recommended in the user manual.3. Damage due to improper installation.4. Damage due to use of uncertified components.5. Damage due to use exceeding the permitted parameters.6. Product determined to be an unofficial Gigabyte product.

Chapter 1 Hardware Installation

GA-946GM-DS2/S2 (rev. 2.0) Motherboard - 10 -

Engl

ish

1-2 Feature SummaryCPU LGA775 for Intel CoreTM 2 Extreme quad-core / CoreTM 2 Extreme dual-core /

CoreTM 2 Quad / CoreTM 2 Duo / Pentium processor Extreme Edition /Pentium D / Pentium 4 / Celeron D

L2 cache varies with CPUFront Side Bus Supports 533/800/1066 MHz FSBChipset Northbridge: Intel 946GZ Express Chipset

Southbridge: Intel ICH7LAN Onboard RTL8111B chip (10/100/1000 Mbit)Audio Onboard Realtek ALC888 chip

Supports High Definition Audio Supports 2 / 4 / 6 / 8 channel audio Supports S/PDIF In/Out connection Supports CD In connection

Storage ICH7 Southbrigde- 1 FDD connector, allowing connection of 1 FDD device- 1 IDE connector with UDMA 33/ATA 66/ATA 100 support, allowing

connection of 2 IDE devices- 4 SATA 3Gb/s connectors, allowing connection of 4 SATA 3Gb/s devices

O.S Support Microsoft Windows 2000/XPMemory 4 DDRII DIMM memory slots (supports up to 4 GB memory) (Note 1)

Supports dual channel DDRII 667 (Note 2) /533 unbuffered DIMMs (Note 3) Supports 1.8V DDRII DIMMs

Expanstion Slots 1 PCI Express x16 slot 1 PCI Express x1 slot 2 PCI slots

Internal Connectors 1 24-pin ATX power connector 1 4-pin ATX 12V power connector 1 floppy connector 1 IDE connector 4 SATA 3Gb/s connectors 1 CPU fan connector 1 system fan connector 1 front panel connector 1 front audio connector 1 CD In connector 1 S/PDIF In/Out connector 1 COMB connector 2 USB 2.0/1.1 connectors for additional 4 ports by cables 1 power LED connector 1 Chassis Intrusion connector

"*" Only the GA-946GM-DS2 adopts All-Solid Capacitor design.


English

Rear Panel I/O 1 PS/2 keyboard port 1 PS/2 mouse port 1 parallel port 1 VGA port 1 serial port (COMA) 4 USB 2.0/1.1 ports 1 RJ-45 port 6 audio jacks (Line In / Line Out / MIC In/Surround Speaker Out (Rear

Speaker Out)/Center/Subwoofer Speaker Out/Side Speaker Out)I/O Control IT8718 chipHardware Monitor System voltage detection

CPU/System temperature detection CPU/System fan speed detection CPU warning temperature CPU/System fan failure warning CPU smart fan control

BIOS 1 4 Mbit flash ROM Use of licensed AWARD BIOS

Additional Features Supports @BIOS Supports Download Center Supports Q-Flash Supports EasyTune (only supports Hardware Monitor function) (Note 4) Supports Xpress Install Supports Xpress Recovery2 Supports Xpress BIOS Rescue

Bundle Software Norton Internet Security (OEM revision)Form Factor Micro ATX form factor; 24.4cm x 23.3cm

(Note 1) Due to standard PC architecture, a certain amount of memory is reserved for system usageand therefore the actual memory size is less than the stated amount. For example, 4 GB ofmemory size will instead be shown as 3.xx GB memory during system startup.

(Note 2) To use a DDRII 667 memory module on the motherboard, you must install a 1066/800 MHzFSB processor.

(Note 3) Some memory configurations will cause DDRII 667 memory to operate at 533 MHz andDDRII 533 at 400 MHz. (Please refer to to Page 15 for more information.)

(Note 4) EasyTune functions may vary depending on different motherboards.


Engl

ish

1-3 Installation of the CPU and CPU CoolerBefore installing the CPU, please comply with the following conditions:1. Please make sure that the motherboard supports the CPU.2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong

direction, the CPU will not insert properly. If this occurs, please change the insert directionof the CPU.

3. Please add an even layer of heat paste between the CPU and CPU cooler.4. Please make sure the CPU cooler is installed on the CPU prior to system use,

otherwise overheating and permanent damage of the CPU may occur.5. Please set the CPU host frequency in accordance with the CPU specifications. It is not

recommended that the system bus frequency be set beyond hardware specificationssince it does not meet the required standards for the peripherals. If you wish to setthe frequency beyond the proper specifications, please do so according to your hard-ware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :Enabling the functionality of Hyper-Threading Technology for your computer system requires allof the following platform components:- CPU: An Intel Pentium 4 CPU with HT Technology- Chipset: An Intel Chipset that supports HT Technology- BIOS: A BIOS that supports HT Technology and has it enabled- OS: An operation system that has optimizations for HT Technology

Fig. 1Gently lift the metallever located on theCPU socket to theupright position.

Metal LeverFig. 2Remove the plast iccovering on the CPUsocket.

Fig. 3Notice the small goldcolored triangle locatedon the edge of the CPUsocket. Align theindented corner of the

Fig. 4Once the CPU isproperly inserted,please replace theload plate and push themetal lever back intoits original position.

CPU with the triangle and gently insert the CPU intoposition. (Grasping the CPU firmly between yourthumb and forefinger, carefully place it into the socketin a straight and downwards motion. Avoid twisting orbending motions that might cause damage to the CPUduring installation.)

1-3-1 Installation of the CPU


English

1-3-2 Installation of the CPU Cooler

The CPU cooler may adhere to the CPU as a result of hardening of the heat paste.To preventsuch an occurrence, it is suggested that either thermal tape rather than heat paste be used forheat dissipation or using extreme care when removing the CPU cooler.

Fig. 6Finally, please attach the power connector of theCPU cooler to the CPU fan header located on themotherboard.

Fig. 3Place the CPU cooler atop the CPU and makesure the push pins aim to the pin hole on themotherboard.Pressing down the push pinsdiagonally.

Fig. 4Please make sure the Male and Female push pinare jo ined closely. ( for detai led instal lat ioninstructions, please refer to the CPU cooler instal-lation section of the user manual)

Fig. 5Please check the back of motherboard afterinstalling. If the push pin is inserted as the picture,the installation is complete.

Fig.1Please apply an even layer of heat paste on thesurface of the installed CPU.

Fig. 2(Turning the push pin along the direction of arrow is toremove the CPU cooler, on the contrary, is to install.)Please note the direction of arrow sign on the malepush pin doesn't face inwards before installation. (Thisinstruction is only for Intel boxed fan)

Male Push Pin

Female Push Pin

The top of Female Push Pin


Engl

ish

The motherboard supports DDRII memory modules, whereby BIOS will automatically detect memorycapacity and specifications. Memory modules are designed so that they can be inserted only in one direction.The memory capacity used can differ with each slot.

Before installing the memory modules, please comply with the following conditions:1. Please make sure that the memory used is supported by the motherboard. It is

recommended that memory of similar capacity, specifications and brand be used.2. Before installing or removing memory modules, please make sure that the computer

power is switched off to prevent hardware damage.3. Memory modules have a foolproof insertion design. A memory module can be installed

in only one direction. If you are unable to insert the module, please switch the direction.

1-4 Installation of Memory

Notch

DDRII

Fig.1The DIMM socket has a notch, so the DIMM memory mod-ule can only fit in one direction. Insert the DIMM memorymodule vertically into the DIMM socket. Then push it down.

Fig.2Close the plastic clip at both edges of the DIMM sockets tolock the DIMM module.Reverse the installation steps when you wish to removethe DIMM module.


English

Dual Channel Memory ConfigurationThe GA-946GM-DS2/S2 supports the Dual Channel Technology. After oper-ating the Dual Channel Technology, the bandwidth of Memory Bus willdouble.

The GA-946GM-DS2/S2 includes 4 DIMM sockets, and each Channel has two DIMM sockets asfollowing:

Channel 0 : DDRII1, DDRII2Channel 1 : DDRII3, DDRII4

If you want to operate the Dual Channel Technology, please note the following explanations dueto the limitation of Intel chipset specifications.

1. Dual Channel mode will not be enabled if one or three DDR II memory modules areinstalled.

2. To enable Dual Channel mode with two or four memory modules (it is recommended touse memory modules of identical brand, size, chips, and speed), install the memoryaccording to the dual channel memory configuration table below (Figure 1).

Memory configurations below will cause DDRII 667 memory to operate at 533 MHz (with 1066/800 MHzFSB CPU) and DDRII 533 at 400 MHz (with 800 MHz FSB CPU).(DS: Double Side, SS: Single Side, X: Empty)

Figure 1

2 memory modules

4 memory modules

DDRII1 DDRII2 DDRII3 DDRII4DS/SS X DS/SS XDS/SS X X DS/SSX DS/SS DS/SS XX DS/SS X DS/SSSS SS SS SS

Dual Channel Memory Configuration Table (DS: Double Side, SS: Single Side, X: Empty)

Figure 2

2 memory modules

3 memory modules

4 memory modules

DDRII1 DDRII2 DDRII3 DDRII4SS SS X XX X SS SSSS SS DS/SS XSS SS X DS/SSDS/SS X SS SSX DS/SS SS SSSS SS SS SS

Because of chipset limitations, do not populate both DIMM sockets of the same channel(e.g. DDRII1 and DDRII2) with double-sided memory modules to prevent system's failure tostart or incorrect detection of memory modules.


Engl

ish

1-5 Installation of Expansion CardsYou can install your expansion card by following the steps outlined below:1. Read the related expansion card's instruction document before install the expansion card into the

computer.2. Remove your computer's chassis cover, screws and slot bracket from the computer.3. Press the expansion card firmly into expansion slot in motherboard.4. Be sure the metal contacts on the card are indeed seated in the slot.5. Replace the screw to secure the slot bracket of the expansion card.6. Replace your computer's chassis cover.7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.8. Install related driver from the operating system.

Installing a PCI Express x16 expansion card:

To install a VGA card or to release aninstalled card, users can also press thelatch on the back of the drawable bar asthe picture to the left shows.

Please carefully pull out the small white-drawable bar at the end of the PCI Ex-press x16 slot when you try to install/uninstall the VGA card. Please align theVGA card to the onboard PCI Expressx16 slot and press firmly down on theslot. Make sure your VGA card is lockedby the small white-drawable bar.


English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse ConnectorTo install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboardto the lower port (purple).LPT (Parallel Port)The parallel port allows connection of a printer, scanner and other peripheral devices.Serial Port (COMA)Connects to serial-based mouse or data processing devices.VGA PortMonitor can be connected to VGA port.USB PortBefore you connect your device(s) into USB connector(s), please make sure your device(s) suchas USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.Also make sure your OS supports USB controller. If your OS does not support USB controller,please contact OS vendor for possible patch or driver upgrade. For more information pleasecontact your OS or device(s) vendors.LAN PortThe provided Internet connection is Gigabit Ethernet, providing data transfer speeds of10/100/1000Mbps.Center/Subwoofer Speaker OutThe default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected toCenter/Subwoofer Speaker Out jack.Surround Speaker Out (Rear Speaker Out)The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can beconnected to Surround Speaker Out (Rear Speaker Out) jack.Side Speaker OutThe default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker Outjack.Line InThe default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.Line Out (Front Speaker Out)The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surroundspeakers can be connected to Line Out (Front Speaker Out) jack.MIC InThe default MIC In jack. Microphone must be connected to MIC In jack.


Engl

ish

1-7 Connectors Introduction

In addition to the default speakers settings, the ~ audio jacks can be reconfigured toperform different functions via the audio software. Only microphones still MUST be connectedto the default Mic In jack ( ) . Please refer to the 2-/4-/6-/8- channel audio setup steps fordetailed software configuration information.

1) ATX_12V2) ATX (Power Connector)3) CPU_FAN4) SYS_FAN5) FDD6) IDE7) SATAII0/1/2/38) F_PANEL9) F_AUDIO

10) PWR_LED11) CD_IN12) SPDIF_IO13) F_USB1/F_USB214) COMB15) C I16) CLR_CMOS17) BATTERY

1012 135

31

2

8

9

15

6

7

4

17

16

14

11


English

Pin No. Definition13 3.3V14 -12V15 GND16 PS_ON(soft On/Off)17 GND18 GND19 GND20 -5V21 +5V22 +5V23 +5V (Only for 24-pin ATX)24 GND(Only for 24-pin ATX)

Pin No. Definition1 3.3V2 3.3V3 GND4 +5V5 GND6 +5V7 GND8 Power Good9 5V SB(stand by +5V)10 +12V11 +12V(Only for 24-pin ATX)12 3.3V(Only for 24-pin ATX)

1/2) ATX_12V/ATX (Power Connector)With the use of the power connector, the power supply can supply enough stable power to allthe components on the motherboard. Before connecting the power connector, please make surethat all components and devices are properly installed. Align the power connector with itsproper location on the motherboard and connect tightly.The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V powerconnector is not connected, the system will not start.Caution!Please use a power supply that is able to handle the system voltage requirements. It isrecommended that a power supply that can withstand high power consumption be used (300Wor greater). If a power supply is used that does not provide the required power, the result canlead to an unstable system or a system that is unable to start.If you use a 24-pin ATX power supply, please remove the small cover on the power connectoron the motherboard before plugging in the power cord ; Otherwise, please do not remove it.

Pin No. Definition1 GND2 GND3 +12V4 +12V

1 13

2412

3

1

4

2

ATX_12V

ATX


Engl

ish

1

2

33

34

3/4) CPU_FAN/SYS_FAN (Cooler Fan Power Connector)The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only forCPU_FAN) power connector and possesses a foolproof connection design.Most coolers are designed with color-coded power connector wires. A red power connector wireindicates a positive connection and requires a +12V power voltage. The black connector wire isthe ground wire (GND).Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to preventCPU damage or system hanging caused by overheating.

5) FDD (Floppy Connector)The FDD connector is used to connect the FDD cable while the other end of the cable connects to theFDD drive. The types of FDD drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB and2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDDconnector.

Pin No. Definition1 GND2 +12V/Speed Control3 Sense4 Speed Control

Pin No. Definition1 GND2 +12V3 Sense

CPU_FAN:

SYS_FAN:

SYS_FAN

CPU_FAN

1

1


English

6) IDE (IDE Connector)An IDE device connects to the computer via an IDE connector. One IDE connector can connect toone IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or opticaldrive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Masterand the other as Slave (for information on settings, please refer to the instructions located on the IDEdevice). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

7) SATAII0/1/2/3 (SATA 3Gb/s Connector)SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the SerialATA and install the proper driver in order to work properly.

Pin No. Definition1 GND2 TXP3 TXN4 GND5 RXN6 RXP7 GND

40 39

2 1

SATAII3SATAII2

SATAII1SATAII0

17

71

17

71


Engl

ish

8) F_PANEL (Front Panel Jumper)Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassisfront panel to the F_PANEL connector according to the pin assignment below.

12

1920

HD-

HD+ R

ES+

RES- NC

IDE Hard Disk Active LED

Reset Switch

SPEA

K-

MSG-

MSG+

PW-

PW+

Message LED/Power/

Sleep LED

Speaker Connector

SPEA

K+

PowerSwitch

HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)Pin 2: LED cathode(-)

SPEAK (Speaker Connector) Pin 1: PowerPin 2- Pin 3: NCPin 4: Data(-)

RES (Reset Switch) Open: NormalClose: Reset Hardware System

PW (Power Switch) Open: NormalClose: Power On/Off

MSG (Message LED/Power/Sleep LED) Pin 1: LED anode(+)Pin 2: LED cathode(-)

NC NC


English

9) F_AUDIO (Front Audio Connector)This connector supports either HD (High Definition) or AC97 front panel audio module. If you wishto use the front audio function, connect the front panel audio module to this connector. Check the pinassignments carefully while you connect the front panel audio module. Incorrect connectionbetween the module and connector will make the audio device unable to work or even damage it.For optional front panel audio module, please contact your chassis manufacturer.

By default, the audio driver is configured to support HD Audio. To connect an AC97 front panelaudio module to this connector, please refer to the instructions on Page 69 about the softwaresettings.

AC'97 Audio:HD Audio:Pin No. Definition

1 MIC2_L2 GND3 MIC2_R4 -ACZ_DET5 LINE2_R6 FSENSE17 FAUDIO_JD8 No Pin9 LINE2_L10 FSENSE2

Pin No. Definition1 MIC2 GND3 MIC Power4 NC5 Line Out (R)6 NC7 NC8 No Pin9 Line Out (L)10 NC

12

910


Engl

ish

Pin No. Definition1 MPD+2 MPD-3 MPD-

1

11) CD_IN (CD IN)Connect CD-ROM or DVD-ROM audio out to the connector.

Pin No. Definition1 CD-L2 GND3 GND4 CD-R

1

10) PWR_LEDThe PWR_LED connector is connected with the system power indicator to indicate whether thesystem is on/off. It will blink when the system enters suspend mode (S1).


English

Pin No. Definition1 Power2 No Pin3 SPDIF4 SPDIFI5 GND6 GND

6

1 5

2

12) SPDIF_IO (S/PDIF In/Out Connector)The S/PDIF output is capable of providing digital audio to external speakers or compressed AC3data to an external Dolby Digital Decoder. Use this feature only when your stereo system hasdigital input function. Use S/PDIF IN feature only when your device has digital output function.Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully whileyou connect the S/PDIF cable, incorrect connection between the cable and connector will make thedevice unable to work or even damage it. For optional S/PDIF cable, please contact your localdealer.

13) F_USB1/F_USB2 (Front USB Connector)Be careful with the polarity of the front USB connector. Check the pin assignment carefully whileyou connect the front USB cable, incorrect connection between the cable and connector will makethe device unable to work or even damage it. For optional front USB cable, please contact yourlocal dealer.

Pin No. Definition1 Power(5V)2 Power(5V)3 USB DX-4 USB Dy-5 USB DX+6 USB Dy+7 GND8 GND9 No Pin10 NC

2

10

1

9


Engl

ish

14) COMB (COMB Connector)Be careful with the polarity of the COMB connector. Check the pin assignments while you connectthe COMB cable. Please contact your nearest dealer for optional COMB cable.

10

9

2

1

Pin No. Definition1 NDCDB-2 NSINB3 NSOUTB4 NDTRB-5 GND6 NDSRB-7 NRTSB-8 NCTSB-9 NRIB-10 No Pin

15) CI (Chassis Intrusion, Case Open)This 2-pin connector allows your system to detect if the chassis cover is removed. You can checkthe "Case Opened" status in BIOS Setup.

Pin No. Definition1 Signal2 GND1


English

16) CLR_CMOS (Clear CMOS)You may clear the CMOS data to its default values by this header. To clear CMOS, temporarilyshort the two pins. Default doesn't include the jumper to avoid improper use of this header.

Open: Normal

Short: Clear CMOS

17) BATTERY

Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type recommendedby the manufacturer.

Dispose of used batteries according to the manufacturer'sinstructions.

If you want to erase CMOS...1. Turn off the computer and unplug the power cord.2. Gently take out the battery and put it aside for about one minute.(Or you can use a metal object to connect the positive and nega-tive pins in the battery holder to makethem short for five seconds.)3. Re-install the battery.4. Plug the power cord in and turn on the computer.


Engl

ish

BIOS Setup- 29 -

English

CONTROL KEYS< >< >< >< > Move to select item Select Item Main Menu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Item Help Restore the previous CMOS value from CMOS, only for Option Page Setup

Menu Load the fail-safe default CMOS value from BIOS default table Load the Optimized Defaults Q-Flash utility System Information Save all the CMOS changes, only for Main Menu

Main MenuThe on-line description of the highlighted setup function is displayed at the bottom of the screen.Status Page Setup Menu / Option Page Setup MenuPress F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-tions for the highlighted item. To exit the Help Window press .

Chapter 2 BIOS Setup

Because BIOS flashing is potentially risky, please do it with caution and avoid inadequateoperation that may result in system malfunction.

BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configurerequired settings or to activate certain system features.The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.When the power is turned off, the battery on the motherboard supplies the necessary power to theCMOS SRAM.When the power is turned on, pressing the button during the BIOS POST (Power-On Self Test) willtake you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".If you wish to upgrade to a new BIOS, either Gigabyte's Q-Flash or @BIOS utility can be used.Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operatingsystem.@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS butdirectly download and update BIOS from the Internet.


Engl

ish

The Main Menu (For example: BIOS Ver. : GA-946GM-DS2 F1a)Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on thescreen. Use arrow keys to select among the items and press to accept or enter the sub-menu.

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` Frequency/Voltage Control

Load Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit KLJI: Select ItemF8: Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

: Boot Menu

Award Modular BIOS v6.00PG, An Energy Star AllyCopyright (C) 1984-2006, Award Software, Inc.

Intel 946GZ BIOS for 946GM-DS2 F1a....

:BIOS Setup/Q-Flash, : Xpress Recovery2, : Boot Menu10/16/2006-946GZ- ICH7-6A79LG0LC-00

: Boot MenuSelect boot sequence for onboard (or add-on cards) device.

Use < > or < > to select a device, then press enter to accept . Press to exit this menu.Boot Menu

FloppyLS120Hard DiskCDROMZIPUSB-FDDUSB-ZIPUSB-CDROMUSB-HDDLAN

== Select a Boot First device ==

KL:Move Enter :Accept ESC:Exit

1. If you dont find the settings you want, press "Ctrl+F1" to access advanced options.2. Select the Load Optimized Defaults item in the BIOS Setup when somehow the system

is not stable as usual. This action makes the system reset to the default settings for stability.3. The BIOS Setup menus described in this chapter are for reference only and may differ from

the exact settings for your motherboard.

BIOS Setup- 31 -

English

Standard CMOS FeaturesThis setup page includes all the items in standard compatible BIOS.

Advanced BIOS FeaturesThis setup page includes all the items of Award special enhanced features.

Integrated PeripheralsThis setup page includes all onboard peripherals.

Power Management SetupThis setup page includes all the items of Green function features.

PnP/PCI ConfigurationsThis setup page includes all the configurations of PCI & PnP ISA resources.

PC Health StatusThis setup page is the System auto detect Temperature, voltage, fan, speed.

Frequency/Voltage ControlThis setup page is control CPU clock and frequency ratio.

Load Fail-Safe DefaultsFail-Safe Defaults indicates the value of the system parameters which the system would be in safeconfiguration.

Load Optimized DefaultsOptimized Defaults indicates the value of the system parameters which the system would be inbest performance configuration.

Set Supervisor PasswordChange, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.

Set User PasswordChange, set, or disable password. It allows you to limit access to the system.

Save & Exit SetupSave CMOS value settings to CMOS and exit setup.

Exit Without SavingAbandon all CMOS value changes and exit setup.


Engl

ish

2-1 Standard CMOS Features

DateThe date format is , , , .

Week The week, from Sun to Sat, determined by the BIOS and is display-onlyMonth The month, Jan. Through Dec.Day The day, from 1 to 31 (or the maximum allowed in the month)Year The year, from 1999 through 2098

TimeThe times format in . The time is calculated based on the 24-hourmilitary-time clock. For example, 1 p.m. is 13:00:00.IDE Channel 0 Master/Slave

IDE HDD Auto-DetectionPress "Enter" to select this option for automatic device detection.

IDE Channel 0 Master/Slave IDE/SATA Device Setup. You can use one of three methods:Auto Allows BIOS to automatically detect IDE/SATA devices during POST(default)None Select this if no IDE/SATA devices are used and the system will skip the

automatic detection step and allow for faster system start up.Manual User can manually input the correct settings

Access Mode Use this to set the access mode for the hard drive. The four options are:CHS/LBA/Large/Auto(default:Auto)

IDE Channel 2, 3 Master/SlaveIDE Auto-Detection

Press "Enter" to select this option for automatic device detection.Extended IDE Drive. IDE/SATA Device Setup. You can use one of the two methods:

Auto Allows BIOS to automatically detect IDE/SATA devices during POST(default)None Select this if no IDE/SATA devices are used and the system will skip the

automatic detection step and allow for faster system start up.

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwareStandard CMOS Features

Date (mm:dd:yy) Fri, Mar 18 2006Time (hh:mm:ss) 18:25:04

` IDE Channel 0 Master [None]` IDE Channel 0 Slave [None]` IDE Channel 2 Master [None]` IDE Channel 2 Slave [None]` IDE Channel 3 Master [None]` IDE Channel 3 Slave [None]

Drive A [1.44M, 3.5"]Floppy 3 Mode Support [Disabled]

Halt On [All, But Keyboard]

Base Memory 640KExtended Memory 511MTotal Memory 512M

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General HelpF5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults

Item HelpMenu Level`

Change the day, month,year

Sun. to Sat.

Jan. to Dec.

1 to 31 (or maximumallowed in the month)

1999 to 2098

BIOS Setup- 33 -

English

Capacity Capacity of currently installed hard disk.Cylinder Number of cylindersHead Number of headsPrecomp Write precompLanding Zone Landing zoneSector Number of sectors

Drive AThe category identifies the types of floppy disk drive A that has been installed in the computer.

None No floppy drive installed360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity

(3.5 inch when 3 Mode is Enabled).720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity.2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)Disabled Normal Floppy Drive. (Default value)Drive A Drive A is 3 mode Floppy Drive.

Halt onThe category determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error that may be detected and youwill be prompted.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other

errors. (Default value)All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all

other errors.MemoryThe category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base MemoryThe POST of the BIOS will determine the amount of base (or conventional) memory installedin the system.The value of the base memory is typically 512K for systems with 512K memory installed onthe motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended MemoryThe BIOS determines how much extended memory is present during the POST.This is the amount of memory located above 1 MB in the CPU's memory address map.

Total MemoryThis item displays the memory size that used.


Engl

ish

2-2 Advanced BIOS Features

Hard Disk Boot PrioritySelect boot sequence for onboard(or add-on cards) SCSI, RAID, etc.Use < > or < > to select a device, then press to move it up, or to move it down the list.Press to exit this menu.First / Second / Third Boot Device

Floppy Select your boot device priority by Floppy.LS120 Select your boot device priority by LS120.Hard Disk Select your boot device priority by Hard Disk.CDROM Select your boot device priority by CDROM.ZIP Select your boot device priority by ZIP.USB-FDD Select your boot device priority by USB-FDD.USB-ZIP Select your boot device priority by USB-ZIP.USB-CDROM Select your boot device priority by USB-CDROM.USB-HDD Select your boot device priority by USB-HDD.LAN Select your boot device priority by LAN.Disabled Disable this function.

Password CheckSetup The system will boot but will not access to Setup page if the correct

password is not entered at the prompt. (Default value)System The system will not boot and will not access to Setup page if the correct

password is not entered at the prompt.If you want to cancel the setting of password, please just press ENTER to make [SETUP] empty.HDD S.M.A.R.T. CapabilityThis feature allows your hard disk to report read/write errors and to issue warnings when third-party hardware monitor utility is installed.

Enabled Enable HDD S.M.A.R.T. capability.Disabled Disable HDD S.M.A.R.T. capability. (Default value)

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwareAdvanced BIOS Features

` Hard Disk Boot Priority [Press Enter]First Boot Device [Floppy]Second Boot Device [Hard Disk]Third Boot Device [CDROM]Password Check [Setup]HDD S.M.A.R.T. Capability [Disabled]CPU Hyper-Threading (Note) [Enabled]Limit CPUID Max. to 3 (Note) [Disabled]No-Execute Memory Protect (Note) [Enabled]CPU Enhanced Halt (C1E) (Note) [Enabled]CPU Thermal Monitor 2(TM2) (Note) [Enabled]CPU EIST Function (Note) [Enabled]Virtualization Technology (Note) [Enabled]Init Display First [PCI]Onboard VGA [Enable If No Ext PEG]On-Chip Frame Buffer Size [8MB]



Select Hard Disk BootDevice Priority

(Note) This item will show up when you install a processor that supports this function.

BIOS Setup- 35 -

English

CPU Hyper-Threading (Note)Enabled Enable CPU Hyper Threading Feature. Please note that this feature is only

working for operating system with multi processors mode supported. (Defaultvalue)

Disabled Disable CPU Hyper Threading.Limit CPUID Max. to 3(Note)

Enabled Limit CPUID Maximum value to 3 when use older OS like NT4.Disabled Disable CPUID Limit for windows XP. (Default value)

No-Execute Memory Protect (Note)Enabled Enable No-Execute Memory Protect function. (Default value)Disabled Disable No-Execute Memory Protect function.

CPU Enhanced Halt (C1E) (Note)Enabled Enable CPU Enhanced Halt (C1E) function. (Default value)Disabled Disable CPU Enhanced Halt (C1E) function.

CPU Thermal Monitor 2 (TM2) (Note)Enabled Enable CPU Thermal Monitor 2 (TM2) function. (Default value)Disabled Disable CPU Thermal Monitor 2 (TM2) function.

CPU EIST Function (Note)Enabled Enable CPU EIST function. (Default value)Disabled Disable EIST function.

Virtualization Technology (Note)Enabled Enable Virtualization Technology. (Default value)Disabled Disable this function.

Init Display FirstThis feature allows you to select the first initiation of the monitor display from which card when youinstall a PCI card and a PCI Express VGA card on the motherboard.

PCI Set Init Display First to PCI VGA card. (Default value)Onboard Set Init Display First to onboard VGA function.PEG Set Init Display First to PCI Express VGA card.

Onboard VGAThis item allows the user to decide when to activate the onboard VGA function.

Enable If No Ext PEG Activate the onboard VGA first only when no PCI Express VGA card isinstalled. (Default value)

Always EnableAlways activate the onboard VGA first, whether or not a PCI Express card is installed. If you wishto set up a dual view configuration, set this item to Always Enable.On-Chip Frame Buffer Size

1MB Set on-chip frame buffer size to 1 MB.8MB Set on-chip frame buffer size to 8 MB. (Default value)

(Note) This item will show up when you install a processor that supports this function.


Engl

ish

2-3 Integrated Peripherals

On-Chip Primary PCI IDEEnabled Enable the first onboard IDE channel. (Default value)Disabled Disable the first onboard IDE channel.

On-Chip SATA ModeDisabled Disable this function.Auto BIOS will auto detect. (Default value)Combined Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

the motherboard; 2 for SATA and the other for PATA.Enhanced Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6

HDDs to use; 4 SATA HDDs plus 2 PATA HDDs.Non-Combined Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

PATA mode. Support a maximum of 4 SATA devices. PATA devices will beignored.

PATA IDE Set toCh.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave.Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave. (Default value)

SATA Port 0/2 Set toThis value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave,this function will auto set to Ch. 0 Master/Slave.SATA Port 1/3 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".If PATA IDE were set to Ch. 0 Master/Slave,this function will auto set to Ch. 1 Master/Slave.USB Controller

Enabled Enable USB Controller. (Default value)Disabled Disable USB Controller.

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwareIntegrated Peripherals

On-Chip Primary PCI IDE [Enabled]On-Chip SATA Mode [Auto]

x PATA IDE Set to Ch.0 Master/SlaveSATA Port 0/2 Set to Ch.2 Master/SlaveSATA Port 1/3 Set to Ch.3 Master/SlaveUSB Controller [Enabled]USB 2.0 Controller [Enabled]USB Keyboard Support [Disabled]USB Mouse Support [Disabled]Legacy USB storage detect [Enabled]Azalia Codec [Auto]Onboard H/W LAN [Enabled]

` SMART LAN [Press Enter]OnBoard LAN Boot ROM [Disabled]Onboard Serial Port 1 [3F8/IRQ4]Onboard Serial Port 2 [2F8/IRQ3]Onboard Parallel Port [378/IRQ7]Parallel Port Mode [SPP]



BIOS Setup- 37 -

English

USB 2.0 ControllerDisable this function if you are not using onboard USB 2.0 feature.

Enabled Enable USB 2.0 Controller. (Default value)Disabled Disable USB 2.0 Controller.

USB Keyboard SupportEnabled Enable USB Keyboard Support.Disabled Disable USB Keyboard Support. (Default value)

USB Mouse SupportEnabled Enable USB Mouse Support.Disabled Disable USB Mouse Support. (Default value)

Legacy USB storage detectThis option allows users to decide whether to detect USB storage devices, including USB flashdrives and USB hard drives during POST.

Enabled BIOS will scan all USB storage devices. (Default value)Disabled Disable this function.

Azalia CodecAuto Auto detect Azalia audio function. (Default value)Disabled Disable Azalia audio function.

Onboard H/W LANEnabled Enable Onboard H/W LAN function. (Default value)Disabled Disable this function.

SMART LAN (LAN Cable Diagnostic Function)CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

SMART LANItem HelpMenu Level`

Start detecting at Port.....Pair1-2 Status = Open / Length = 0.0mPair3-6 Status = Open / Length = 0.0mPair4-5 Status = Open / Length = 0.0mPair7-8 Status = Open / Length = 0.0m


This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LANcable. This feature will detect cabling issue and report the approximate distance to the fault or short.Refer to the following information for diagnosing your LAN cable:

When No LAN Cable Is Attached...If no LAN cable is attached to the motherboard, the Status fields of all four pairs of wires will showOpen and the Length fields show 0.0m, as shown in the figure above.


Engl

ish

Link Detected Displays transmission speedCable Length Displays the approximate length of the attached LAN cable

Note: The Gigabit hub will only operate at a speed of 10/100Mbps in MS-DOS mode; it will operateat a normal speed of 10/100/1000Mbps in Windows mode or when the LAN Boot ROM is activated.

When a Cable Problem Occurs...If a cable problem occurs on a specified pair of wires, the Status field will show Short and thelength shown will be the approximate distance to the fault or short.Example: Pair1-2 Status = Short / Length = 1.6mExplanation: A fault or short might occur at about 1.6m on Pair 1-2.

Note: Pair 4-5 and Pair 7-8 are not used in a 10/100 Mbps environment, their Status fields willshow Open, and the length shown is the approximate length of the attached LAN cable

Start detecting at Port.....Link Detected --> 100MbpsCable Length= 30m

When LAN Cable Is Functioning Normally...If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub,the following message will appear:

OnBoard LAN Boot ROMThis function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled Enable this function.Disabled Disable this function. (Default value)

Onboard Serial Port 1Auto BIOS will automatically setup the port 1 address.3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8/IRQ3.3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8/IRQ4.2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8/IRQ3.Disabled Disable onboard Serial port 1.

Onboard Serial Port 2Auto BIOS will automatically setup the port 2 address.3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8/IRQ4.2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8/IRQ4.2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8/IRQ3.Disabled Disable onboard Serial port 2.

Onboard Parallel PortDisabled Disable onboard LPT port.378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

BIOS Setup- 39 -

English

Parallel Port ModeSPP Using the onboard LPT port as Standard Parallel Port. (Default value)EPP Using the onboard LPT port as Enhanced Parallel Port.ECP Using the onboard LPT port as Extended Capabilities Port.ECP+EPP Using the onboard LPT port as ECP & EPP mode.

2-4 Power Management SetupCMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Power Management SetupACPI Suspend Type [S1(POS)]Soft-Off by PWR-BTTN [Instant-Off]PME Event Wake Up [Enabled]Power On by Ring [Enabled]Resume by Alarm [Disabled]

x Date (of Month) Alarm Everydayx Time (hh:mm:ss) Alarm 0 : 0 : 0

Power On By Mouse [Disabled]Power On By Keyboard [Disabled]

x KB Power ON Password EnterAC Back Function [Soft-Off]



ACPI Suspend TypeS1(POS) Set ACPI suspend type to S1/POS (Power On Suspend). (Default

value)S3(STR) Set ACPI suspend type to S3/STR (Suspend To RAM).

Soft-Off by PWR-BTTNInstant-Off Press power button to power off the system instantly. (Default value)Delay 4 Sec. Press power button 4 sec. to power off. Enter suspend if button is

pressed less than 4 sec.PME Event Wake UpThis feature requires an ATX power supply that provides at least 1A on the 5VSB lead.

Disabled Disable this function.Enabled Enable PME as wake up event. (Default value)

Power On by RingDisabled Disable Power on by Ring function.Enabled Enable Power on by Ring function. (Default value)

Resume by AlarmYou can enable this item and key in a date/time to power on system.

Disabled Disable this function. (Default value)Enabled Enable alarm function to POWER ON system.


Engl

ish

If Resume by Alarm is Enabled.Date (of Month) Alarm : Everyday, 1~31Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

Power On By MouseDisabled Disable this function. (Default value)Double Click Double click on PS/2 mouse left button to power on the system.

Power On By KeyboardPassword Enter from 1 to 5 characters to set the Keyboard Power On Password.Disabled Disable this function. (Default value)Keyboard 98 If your keyboard has "POWER Key" button, you can press the key to

power on the system.KB Power ON PasswordWhen "Power On by Keyboard" set at Password, you can set the password here.

Enter Input password (from 1 to 5 characters) and press Enter to set theKeyboard Power On password.

AC Back FunctionSoft-Off When AC-power back to the system, the system will be in "Off" state.

(Default value)Full-On When AC-power back to the system, the system always in "On" state.Memory When AC-power back to the system, the system will return to the Last

state before AC-power off.

BIOS Setup- 41 -

English

2-5 PnP/PCI Configurations

PCI1 IRQ AssignmentAuto Auto assign IRQ to PCI 1. (Default value)3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.

PCI2 IRQ AssignmentAuto Auto assign IRQ to PCI 2. (Default value)3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwarePnP/PCI Configurations

PCI1 IRQ Assignment [Auto]PCI2 IRQ Assignment [Auto]




Engl

ish

2-6 PC Health Status

Reset Case Open StatusDisabled Don't reset case open status. (Default value)Enabled Clear case open status at next boot.

Case OpenedIf the case is closed, "Case Opened" will show "No".If the case have been opened, "Case Opened" will show "Yes".If you want to reset "Case Opened" value, set "Reset Case Open Status" to "Enabled" and saveCMOS, your computer will restart.Current Voltage(V) Vcore / DDR18V / +3.3V / +12V

Detect system's voltage status automatically.Current System/CPU Temperature

Detect system/CPU temperature automatically.Current CPU/SYSTEM FAN Speed (RPM)

Detect CPU/System fan speed status automatically.CPU Warning Temperature

60oC / 140oF Monitor CPU temperature at 60oC / 140oF.70oC / 158oF Monitor CPU temperature at 70oC / 158oF.80oC / 176oF Monitor CPU temperature at 80oC / 176oF.90oC / 194oF Monitor CPU temperature at 90oC / 194oF.Disabled Disable this function. (Default value)

CPU/SYSTEM FAN Fail WarningDisabled Disable the fan fail warning function. (Default value)Enabled Enable the fan fail warning function.

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwarePC Health Status

Reset Case Open Status [Disabled]Case Opened NoVcore OKDDR18V OK+3.3V OK+12V OKCurrent System Temperature 15oCCurrent CPU Temperature 47oCCurrent CPU FAN Speed 3375 RPMCurrent SYSTEM FAN Speed 0 RPMCPU Warning Temperature [Disabled]CPU FAN Fail Warning [Disabled]SYSTEM FAN Fail Warning [Disabled]CPU Smart FAN Control [Enabled]CPU Smart FAN Mode [Auto]



BIOS Setup- 43 -

English

CPU Smart FAN ControlDisabled Disable this function.Enabled When this function is enabled, CPU fan will run at different speed

depending on CPU temperature. (Default value)CPU Smart FAN ModeThis option is available only when CPU Smart FAN Control is enabled.

Auto BIOS autodetects the type of CPU fan you installed and sets the optimalCPU Smart FAN control mode for it. (Default value)

Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable.PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable.

Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables.However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWMcontrol specifications. With such CPU fans, selecting PWM will not effectively reduce the fanspeed.


Engl

ish

2-7 Frequency/Voltage Control

Incorrectly using these features may result in system instability or corruption.Doing a overclock or overvoltage on CPU, chipsets and memory modules may result indamages or shortened life expectancy to these components.Please be aware that the menu items are for power users only.

(Note) This item will show up when you install a processor which supports this function.

CMOS Setup Utility-Copyright (C) 1984-2006 Award SoftwareFrequency/Voltage Control

CPU Clock Ratio (Note) [16X]System Memory Multiplier [Auto]Memory Frequency (Mhz) 533



CPU Clock Ratio (Note)This setup option will automatically assign by CPU detection.The option will display "Locked" and read only if the CPU ratio is not changeable.System Memory MultiplierThe adjustable range will vary based on the CPU FSB. Default value: Auto (set memoryfrequency by DRAM SPD data). Wrong frequency settings may cause system unable to boot.Clear CMOS to overcome wrong frequency issue.Memory Frequency (Mhz)The values depend on System Memory Multiplier setting.

BIOS Setup- 45 -

English

2-8 Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum systemperformance.

2-9 Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automaticallydetects.


` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` Frequency/Voltage ControlESC: Quit KLJI: Select ItemF8: Q-Flash F10: Save & Exit Setup

Load Fail-Safe Defaults


Load Fail-Safe Defaults (Y/N)? N



Load Optimized Defaults


Load Optimized Defaults (Y/N)? N


Engl

ish

2-10 Set Supervisor/User Password

When you select this function, the following message will appear at the center of the screen to assistyou in creating a password.Type the password, up to eight characters, and press . You will be asked to confirm thepassword. Type the password again and press . You may also press to abort theselection and not enter a password.To disable password, just press when you are prompted to enter password. A message"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password isdisabled, the system will boot and you can enter Setup freely.The BIOS Setup program allows you to specify two separate passwords:SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOSSetup program function. When enabled, the Supervisor password is required for entering the BIOSSetup program and having full configuration fields, the User password is required to access only basicitems.If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be promptedfor the password every time the system is rebooted or any time you try to enter Setup Menu.If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted onlywhen you try to enter Setup.



Change/Set/Disable Password


Enter Password:

BIOS Setup- 47 -

English

2-11 Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.Type "N" will return to Setup Utility.

2-12 Exit Without Saving

Type "Y" will quit the Setup Utility without saving to RTC CMOS.Type "N" will return to Setup Utility.



Save Data to CMOS


Save to CMOS and EXIT (Y/N)? Y



Abandon all Data


Quit Without Saving (Y/N)? N


Engl

ish

Install Drivers- 49 -

English

Chapter 3 Install DriversPictures below are shown in Windows XP.Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driverCD-title will auto start and show the installation guide. If not, please double click the CD-ROMdevice icon in "My computer", and execute the Run.exe.

3-1 Install Chipset Drivers

After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers thatrecommended to install. Please pick the item that you want and press "install" followed the item; or you canpress "Xpress Install" to install all items defaulted.

Some device drivers will restart your system automatically. After restartingyour system the "Xpress Install" will continue to install other drivers.System will reboot automatically after install the drivers, afterward you caninstall others application.

For USB2.0 driver support under Windows XP operating system, pleaseuse Windows Service Pack. After install Windows Service Pack, it will showa question mark "?" in "Universal Serial Bus controller" under "DeviceManager". Please remove the question mark and restart the system (Systemwill auto-detect the right USB2.0 driver).


Engl

ish

3-2 Software ApplicationsThis page displays all the tools that Gigabyte developed and some free software, you can choose anyoneyou want and press "install" to install them.

3-3 Driver CD InformationThis page lists the contents of software and drivers in this CD-title.

Install Drivers- 51 -

English

3-4 Hardware InformationThis page lists all device you have for this motherboard.

3-5 Contact UsPlease see the last page for details.


Engl

ish

Appendix- 53 -

English

Chapter 4 Appendix4-1 Unique Software Utilities(Not all model support these Unique Software Utilities, please check your MB features.)

4-1-1 EasyTune 5 IntroductionEasyTune 5 presents the most convenient Windows based system performance enhancement andmanageability utility. Featuring several powerful yet easy to use tools such as 1) Overclocking for enhancingsystem performance, 2) C.I.A. and M.I.B. for special enhancement for CPU and Memory, 3) Smart-Fancontrol for managing fan speed control of both CPU cooling fan and North-Bridge Chipset cooling fan, 4) PChealth for monitoring system status.(Note)

User Interface Overview

(Note) EasyTune 5 functions may vary depending on different motherboards.

Button / Display Description1. Overclocking Enters the Overclocking setting page2. C.I.A./C.I.A.2 and M.I.B./M.I.B.2 Enters the C.I.A./2 and M.I.B./2 setting page3. Smart-Fan Enters the Smart-Fan setting page4. PC Health Enters the PC Health setting page5. GO Confirmation and Execution button6. "Easy Mode" & "Advance Mode" Toggles between Easy and Advance Mode7. Display screen Display panel of CPU frequency8. Function display LEDs Shows the current functions status9. GIGABYTE Logo Log on to GIGABYTE website10. Help button Display EasyTuneTM 5 Help file11. Exit or Minimize button Quit or Minimize EasyTuneTM 5 software


Engl

ish

4-1-2 Xpress Recovery2 IntroductionXpress Recovery2 is designed to provide quick backup and restora-tion of hard disk data. Supporting Microsoft operating systems includingWindows XP/2000/NT/98/Me and DOS, and file systems includingFAT16, FAT32, and NTFS, Xpress Recovery2 is able to back up data

How to use the Xpress Recovery2Initial access by booting from CD-ROM and subsequent access by pressing the F9 key:Steps: After entering BIOS Setup, go to Advanced BIOS Feature and set to boot from CD-ROM. Save

the settings and exit the BIOS Setup. Insert the provided driver CD into your CD-ROM drive. Uponsystem restart, the message which says "Boot from CD/DVD:" will appear in the bottom left cornerof the screen. Press any key to enter Xpress Recovery2.After the steps above are completed, subsequent access to Xpress Recovery2 can be madeby simply pressing the key during system power-on.

1. If you have already entered Xpress Recovery2 by booting from the CD-ROM, you canenter Xpress Recovery2 by pressing the key in the future.

2. System storage capacity and the reading/writing speed of the hard disk will affectthe data backup speed.

3. It is recommended that Xpress Recovery2 be immediately installed once you com-plete installations of OS and all required drivers as well as software.

on hard disks on PATA and SATA IDE controllers. After Xpress Recovery2 is executed from CD-ROMfor the first time, it will stay permanent in your hard disk. If you wish to run Xpress Recovery2 later, youcan simply press F9 during system bootup to enter Xpress Recovery2 without the CD-ROM.

System requirements:1. Intel x86 platforms2. At least 64M bytes of system memory3. VESA-supported VGA cards


Intel 946GZ BIOS for 946GM-DS2 F1a....

:BIOS Setup/Q-Flash, : Xpress Recovery2, : Boot Menu10/16/2006-946GZ- ICH7-6A79LG0LC-00 : Xpress Recovery2

Boot from CD/DVD:..Boot from CD/DVD:Press any key to startup XpressRecovery2.....

Appendix- 55 -

English

1. RESTORE:Restore the backed-up data to your hard disk.(This button will not appear if there is no backupfile.)

2. BACKUP:Back up data from hard disk.

3. REMOVE:Remove previously-created backup filesto release disk space.(This button will not appear if there is no backupfile.)

4. REBOOT:Exit the main screen and restart the system.

The Main Screen of Xpress Recovery2

Limitations:1. Not compatible to Xpress Recovery.2. For the use of Xpress Recovery2, a primary partition must be reserved.3. Xpress Recovery2 will store the backup file at the end of the hard disk, so free space available

on the hard disk for the backup file must be allocated in advance. (A minimum 4GB is recom-mended but the actual space is dependent on the size of the data to be backed up)

4. Capable of backing up hard disks installed with Windows operating systems including DOS andWindows XP/2000/NT/9x/Me.

5. USB hard disks are currently not supported.6. Does not support RAID/AHCI (class code 0104/0106) hard disks.7. Capable of backing up and restoring only the first physical hard disk.Hard disks detection sequence is as follows:

a. PATA IDE primary channelb. PATA IDE secondary channelc . SATA IDE channel 1d. SATA IDE channel 2e. SATA IDE channel 3f. SATA IDE channel 4

Precautions:1. When using hard disks with more than 128G under Windows 2000, be sure to execute the

EnableBigLba.exe program from the driver CD before data backup.2. It is normal that data backup takes longer time than data restoration.3. Xpress Recovery2 is compliant with the GPL regulations.4. On a few motherboards based on Nvidia chipsets, BIOS update is required for Xpress Recovery2

to correctly identify RAID and SATA IDE mode. Please contact your motherboard manufacturer.


Engl

ish

4-1-3 Flash BIOS Method IntroductionMethod 1 : Q-FlashTM UtilityQ-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility,users only have to stay in the BIOS menu when they want to updateBIOS. Q-FlashTM allows users to flash BIOS without any utility in

DOS or Windows. Using Q-FlashTM indicating no more fooling around with any complicated instructionsand operating system since it is in the BIOS menu.

Please note that because updating BIOS has potential risk, please do it with caution!! We aresorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because ofincorrect manipulation of updating BIOS to avoid any claims from end-users.

Before You Begin:Before you start updating BIOS with the Q-FlashTM utility, please follow the steps below first.

1. Download the latest BIOS for your motherboard from Gigabyte's website.2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For

example, 8KNXPU.Fba) to a floppy disk.3. Reboot your PC and press Del to enter BIOS menu.

The BIOS upgrading guides below are separated into two parts.If your motherboard has dual-BIOS, please refer to Part One.If your motherboard has single-BIOS, please refer to Part Two.

Part One:Updating BIOS with Q-FlashTM Utility on Dual BIOS Motherboards.Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboardssupporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the samescreen. This section only deals with how to use Q-Flash utility.In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOSfrom an older version to the latest version. For example, from Fa3 to Fba.

Intel i875P AGPset BIOS for 8KNXP Ultra Fa3Check System Health OK , VCore = 1.5250Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)

Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single ChannelPrimary Master : FUJITSU MPE3170AT ED-03-08Primary Slave : NoneSecondary Master : CREATIVEDVD-RM DVD1242E BC101Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 ForXpress Recovery08/07/2003-i875P-6A79BG03C-00


The BIOS file is Fa3before updating

Appendix- 57 -

English

Entering the Q-FlashTM utility:


` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` MB Intelligent Tweaker(M.I.T.)

Select LanguageLoad Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit F3: Change LanguageF8: Dual BIOS/Q-Flash F10: Save & Exit Setup


Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

Exploring the Q-FlashTM / Dual BIOS utility screenThe Q-Flash / Dual BIOS utility screen consists of the following key components.

Task menu for Dual BIOS utility:Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking atask and pressing Enter key on your keyboard to enable execution of the task.Task menu for Q-Flash utility:Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-tion of the task.Action bar:Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttonsmentioned on your keyboards to perform these actions.

Dual BIOS UtilityBoot From......................................... Main BiosMain ROM Type/Size.............................SST 49LF003A 512K Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection DisableBoot From Main Bios

Auto Recovery EnableHalt On Error Disable

Copy Main ROM Data to BackupLoad Default Settings

Save Settings to CMOSQ-Flash Utility

Load Main BIOS from FloppyLoad Backup BIOS from Floppy

Save Main BIOS to FloppySave Backup BIOS to Floppy

Enter : Run KL:Move ESC:Reset F10:Power Off

Task menu forDual BIOSutility

Task menu forQ-FlashTM utility

Dual BIOS utility bar

Q-FlashTM utility titlebar

Action bar


Engl

ish









Using the Q-FlashTM utility:This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to yourcomputer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,please follow the steps below to flash BIOS.

Steps:1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in

the Q-Flash menu and press Enter button.Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save MainBIOS to Floppy" item.

2. Move to the BIOS file you want to flash and press Enter. In this example, we only download one BIOS file to the floppy disk so only one BIOS file, 8KNXPU.Fba, is listed.

Please confirm again you have the correct BIOS file for your motherboard.

1 file(s) found8KNXPU.Fba 512K

Total size : 1.39M Free size : 911.50KF5 : Refresh DEL : Delete

BIOS file in the floppydisk.









Reading BIOS file from floppy ...>>>>>>>>>>>>>>.....................

Don't Turn Off Power or Reset System

Do not turn off power orreset your system at thisstage!!

After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Appendix- 59 -

English

3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed.









!! Copy BIOS completed - Pass !!

Please press any key to continue

Please do not take out the floppy disk when it begins flashing BIOS.

4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.

You can repeat Step 1 to 4to flash the backup BIOS,too.









Are you sure to RESET ?

[Enter] to continure or [Esc] to abort...

5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically afteryou exit Q-Flash.

After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.

Intel i875P AGPset BIOS for 8KNXP Ultra FbaCheck System Health OK , VCore = 1.5250Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)

Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single ChannelPrimary Master : FUJITSU MPE3170AT ED-03-08Primary Slave : NoneSecondary Master : CREATIVEDVD-RM DVD1242E BC101Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 ForXpress Recovery09/23/2003-i875P-6A79BG03C-00


The BIOS filebecomes Fba afterupdating.


Engl

ish


` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` MB Intelligent Tweaker(M.I.T.)ESC: Quit F3: Change LanguageF8: Dual BIOS/Q-Flash F10: Save & Exit Setup

Load Optimized Defaults

6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move toLoad Optimized Defaults item and press Enter to load BIOS Optimized Defaults. Normally thesystem redetects all devices after BIOS has been upgraded. Therefore, we highly recommendreloading the BIOS defaults after BIOS has been upgraded.


Load Optimized Defaults (Y/N)? Y

Press Y on your keyboard to load defaults.


` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` MB Intelligent Tweaker(M.I.T.)ESC: Quit F3: Change LanguageF8: Dual BIOS/Q-Flash F10: Save & Exit Setup

Save Data to CMOS

7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.System will reboot after you exit the BIOS menu. The procedure is completed.


Save to CMOS and EXIT (Y/N)? Y

Press Y on your keyboard to save and exit.Part Two:Updating BIOS with Q-FlashTM Utility on Single-BIOS Motherboards.This part guides users of single-BIOS motherboards how to update BIOS using the Q-FlashTM utility.


` Standard CMOS Features` Advanced BIOS Features` Integrated Peripherals` Power Management Setup` PnP/PCI Configurations` PC Health Status` MB Intelligent Tweaker(M.I.T.)

Top PerformanceLoad Fail-Safe DefaultsLoad Optimized DefaultsSet Supervisor PasswordSet User PasswordSave & Exit SetupExit Without Saving

ESC: Quit KLJI: Select ItemF8: Q-Flash F10: Save & Exit Setup


Appendix- 61 -

English

Exploring the Q-FlashTM utility screenThe Q-FlashBIOS utility screen consists of the following key components.

Task menu for Q-Flash utility:Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enableexecution of the task.Action bar:Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned onyour keyboards to perform these actions.Using the Q-FlashTM utility:This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to yourcomputer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,please follow the steps below to flash BIOS.Steps:1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the

Q-Flash menu and press Enter button.Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOSto Floppy" item.

2. Move to the BIOS file you want to flash and press Enter. In this example, we only download one BIOS file to the floppy disk so only one BIOS file, 8GE800.F4, is listed.

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Please do not take out the floppy disk when it begins flashing BIOS.

Q-Flash Utility V1.30 Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data EnableUpdate BIOS from Floppy

Save BIOS to FloppyEnter : Run KL:Move ESC:Reset F10:Power Off

Task menu forQ-FlashTM utility

Q-FlashTM utility bar

Action bar

Please confirm again you have the correct BIOS file for your motherboard.

BIOS file in the floppydisk.

Do not turn off power orreset your system at thisstage!!

Q-Flash Utility V1.30 Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data EnableUpdate BIOS from Floppy

Save BIOS to FloppyEnter : Run KL:Move ESC:Reset F10:Power Off

1 file(s) found8GE800.F4 256K

Total size : 1.39M Free size : 1.14MF5 : Refresh DEL : Delete

Q-Flash Utility V1.30 Flash Type/Size.................................SST 49L

Documents

Manual Placa Base Ga-946gm-Ds2 (s2) e