Manual OTTICA

- 1 -

OTTICAManual

OTTICA 20x Zoom NDI 1080/60P PTZ Video Camera 20X Zoom F1.6-F3.5 f5

.5mm-f1

10m

m

20X

Zoom

F1.6 -F3.5 f5.5mm

-f110mm

®

www.ikancorp.com [email protected]

- 2 -

1. Getting Started 3 1.1 Camera Interface 3 1.2 Power-On Initial Configuration 4 1.3 Video Output 4 1.4 Bracket Mount 52. Product Overview 7 2.1 Product Introduction 7 2.1.1 Dimension 7 2.1.2 Accessory 7 2.2 Main Features 8 2.2.1 Camera Performance 8 2.2.2 Network Performance 8 2.3 Technical Specifications 9 2.4 Interface Instructions 11 2.4.1 External Interface 11 2.4.2 Bottom Dial Switch 12 2.4.3 RS-232 Interface 123. Application Instructions 14 3.1 Remote Control 14 3.1.1 Keys Introduction 14 3.1.2 Applications 15 3.2 Menu Settings 17 3.2.1 Main Menu 17 3.2.2 System Settings 17 3.2.3 Camera Settings 18 3.2.4 P/T/Z 20 3.2.5 Video Format 20 3.2.6 Version 21 3.2.7 Restore Default 214. Network Connection 22 4.1 Connecting Mode 22 4.2 IE Log In 23 4.2.1 Web Client 23 4.2.2 Preview 24 4.2.3 Configuration 24 4.2.4 Audio Configuration 24 4.2.5 Video Configuration 24 4.2.6 Network Configuration 28 4.2.7 System Configuration 29 4.2.8 Logout 31 4.2.9 Wireless Network 31

Table of Contents

- 3 -

5. Serial Communication Control 32 5.1 VISCA Protocol List 32 5.1.1 Camera Return Command 32 5.1.2 Camera Control Command 33 5.1.3 Inquiry Command 38 5.2 Pelco-D Protocol Command List 41 5.3 Pelco-P Protocol Command List 426. Camera Maintenance and Troubleshooting 43 6.1 Camera Maintenance 43 6.2 Troubleshooting 43

Table of Contents (cont.)

1. Getting Started

1.1 Camera Interface

1. Camera Lens2. Camera Base3. Remote Controller Receiver Light4. Bottom Dial Switch5. Tripod Screw Hole 6. RS232 Control Interface (input )7. RS232 Control Interface (output )

8. RS485 Input (left +,right-)9. Audio Input Interface10. 3G-SDI interface11. HDMI Interface12. NDI | HX Interface13. DC12V Input Power Supply Socket

Figure 1.1 Interface of ST (standard) Series

- 4 -

1.2 Power-On Initial Configuration

1.3 Video Output

1. Power-On: Connect the DC12V power supply adapter into the power supply socket.2. Initial Configuration: Upon powering on, the remote control receiver light will turn on and start

blinking red. The camera head will move and adjust into the HOME position (intermediate position of both horizontal and vertical). When the remote control receiver light stops blinking red, it will stay on and turn green; this means the self-checking is finished.

- Note: After the Power-On self-test is completed If you press “set preset” then “0”, the camera head automatically moves to the preset HOME position any time you press “0”.

The OTTICA has a variety of video outputs including LAN, HDMI and 3G-SDI.

1. Video Output from LAN

2. HDMI Video Output

3. 3G-SDI Video Output

A. Network Cable Connection Port: No.12 in Figure1.1; B. Webpage Login:

A. HDMI Video Cable Connection: Refer to No.11 in Figure1.1.B. Connect the camera and monitor via HDMI video cable.

A. 3G-SDI video cable connection: Refer to No.10 in Figure1.1B. Connect the camera and the monitor via 3G-SDI video cable

- The OTTICA is set to auto DHCP so you’ll need to connect the camera to devices that can automatically assign an IP address, such as routers and switches.

- Next, you’ll have to use an IP scanning software to find the camera’s IP address (visit the OTTICA product page at www.ikancorp.com to find a link to our recommended software for IP scanning).

- Copy and paste the camera’s IP address and paste it into your web browser’s address bar and press “Enter” to proceed into the login page.

- Enter the user name “admin” and password “admin” (factory default) and press ”Enter” to proceed into the preview page.

- If you do not have the latest version of Flash installed, click on the button that says “Get ADOBE Flash Player.

- After you’ve installed the latest version of flash, the camera feed should be visible and you can now perform PTZ control, video recording, playback, configuration, and other operation.

- NOTE: See chapter 4.1 for more details.

- 5 -

1.4 Bracket Mount

Note: The bracket can only be mounted on a wall or ceiling on either template or concrete wall, but cannot be installed on plasterboard.

Wall Mount Steps

- 6 -

Upside-down Mount Steps

- 7 -

2.1 Product Introduction

2.1.1 Dimensions

2.1.2 Accessories

When unboxing, check that all the supplied accessories are included:

1 x Power Adapter 1 x RS232 Cable 1 x IR Remote Controller 1 x Wall Mounting Bracket 1 x RS485 Connector 1 x Cascade Cable

2. Product Overview

Figure 2.2 Camera Dimensions

- 8 -

2.2 Main Features

2.2.1 Camera Performance

The OTTICA’s features include advanced ISP processing algorithms to provide vivid images with a strong sense of depth, high resolution and fantastic color rendition. It supports H.265/H.264 encoding which makes motion video fluent and clear even with less than ideal bandwidth conditions.

2.2.2 Network Performance

1. Superb High-definition Image: The OTTICA employs 1/2.8 inch high-quality CMOS sensor and supports resolutions up to 1920x1080 with frame rates up to 60 fps.

2. Various Optical Zoom Lens: 5.5-110mm varifocal lens offers 20x optical zoom and viewing angle range from 3.3° to 54.7°

3. Auto Focus Technology: OTTICA’s auto focus algorithm makes the lens fast, accurate, and stable.

4. Low Noise and High SNR: The Low Noise CMOS effectively ensures high SNR of the camera video. Advanced 2D/3D noise reduction technology is also used to further reduce the noise, while ensuring image sharpness.

5. Quiet PTZ: By adopting a high accuracy step-driving motor mechanism, the OTTICA performs smoothly and quietly even when moving quickly to any position.

6. Multi-Format Video Outputs: The OTTICA support HDMI,3G-SDI, wired LAN and wireless LAN interfaces. The 3G-SDI will work up 100m distance with transmission at 1080p60 format.

7.Low-power Sleep Function: The OTTICA supports a low-power sleep/wake up function. The consumption is lower than 500mW while in sleep mode.

8. Support Multiple Control Protocol: The OTTICA supports VISCA, PELCO-D, PELCO-P protocols which can also be automatically recognized.

9. RS-232 Cascade Function: The OTTICA supports RS-232 cascade function which is convenient for installing.

11. 255 Presets Positions: Up to 255 presets (10 presets by IR remote).

1. Audio Input Interface: 16000, 32000, 44100, 48000 sampling frequency and AAC, MP3, PCM audio coding are supported.

2. Multiple Audio/Video Compression: The OTTICA supports H.264/H.265 video compression of resolutions up to 1920x1080p with frame rates up to 60 fps and 2 channel 1920x1080p with 30 fps. AAC, MP3, and PCM audio compression is supported.

3. Multiple Network Protocol: Support NDI|HX; ONVIF, RTSP, RTMP protocols and RTMP push mode, easy to link streaming media server (Wowza, FMS).

- 9 -

2.3 Technical Specifications

Camera Parameters

Sensor 1/2.8 inch high quality HD CMOS sensor

Effective Pixels 16: 9 2.07 megapixel

Video FormatHDMI/SDI Video Format 1080P60/50/30/25/59.94/29.97;1080I60/50/59.94;720P60/50/30/25/59.94/29.97

Optical Zoom20XFocal range: 5.5-110mm

View Angle3.3° (tele)54.7° (wide)

AV F1.6 – F3.5

Digital Zoom 10X

Minimum Illumination 0.5Lux (F1.8, AGC ON)

DNR 2D & 3D DNR

White Balance Auto / Manual/ One Push/ 3000K/ 4000K/5000K/6500K

Focus Auto/Manual

Aperture Auto/Manual

Electronic Shutter Auto/Manual

BLC ON/OFF

WDR OFF/ Dynamic level adjustment

Video adjustmentBrightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve

SNR >55dB

- 10 -

Input / Output Interface

Video InterfacesLAN (NDI | HX 4.0), HDMI, 3G-SDI, Audio-in, RS232 (In&Out), RS485

Image Code Stream Double streams outputs simultaneously

Video Compression format H.264, H.265

Control Signal Interface RS-232 Ring through RS232 output, RS-485

Control ProtocolVISCA/Pelco-D/Pelco-P; Baud Rate: 115200/9600/4800/2400bps

Audio input Interface Double track 3.5mm linear input;

Audio Compression Format AAC/MP3/PMC Audio compression

HD IP Interface100M IP Port(100BASE-TX); 5G WiFi (optional), support NDI, IP Visca control protocol

Network Protocol NDI,RTSP/RTMP,ONVIF

Power Interface HEC3800 Outlet (DC12V)

PTZ Parameters

Pan Rotation ±170°

Tilt Rotation -30°~+90°

Pan Control Speed 0.1 -180°/sec

Tilt Control Speed 0.1-80°/sec

Preset Speed Pan: 60°/sec, Tilt: 30°/sec

Preset Number 255 presets (10 presets by remote controller)

Other Parameters

Supply Adapter AC110V-AC220V to DC12V/2A

Input Voltage DC12V±10%

Input Current 1A(Max)

Consumption 12W (Max)

- 11 -

2.4 Interface Instruction

2.4.1 External Interface

1. External Interface: RS232 Input /Output, RS485 Input, Audio Input, 3G-SDI Output, HDMI Output, LAN, DC12V Power Interface.

Figure 2.3 External Interface Diagram

Other Parameters

Store Temperature 14°F to +140°F

Store Humidity 20% - 95%

Working Temperature 14°F to +122°F

Working Humidity 20%--80%

Dimension 150mmX150mmX167.5mm

Weight 3.08 LBS

Working Environment Indoor

Remote Operation (IP) Remote Upgrade, Reboot and Reset

- 12 -

2.4.2 Bottom Dial Switch

2.4.3 RS-232 Interface

Two DIP switches are set to ON or OFF to select different modes of operation.

Note: Working mode can be applicable for web upgrade.

1. RS-232C Interface Specifications

Figure 2.6 Bottom Dial Switch Diagram

Table 2.2 Dial Switch Setting

No. SW1 SW2 Explanation

1 OFF ON Working Mode

2 ON OFF Updating Mode

Computer / Keyboard & Camera Connection Method

Camera Windows DB-9

1. DTR 1. DCD

2. DSR 2. RXD

3. TXD 3. TXD

4. GND 4. DTR

5. RXD 5. GND

6. GND 6. DSR

7. IR OUT 7. RTS

8. NC 8. CTS

9. RI

- 13 -

No. Port Definition

1 DTR Data Terminal Ready

2 DSR Data Set Ready

3 TXD Transmit Data

4 GND System Ground

5 RXD Receive Data

6 GND System Ground

7 IR OUT IR Commander Signal

8 NC No Connection

No. Port Definition

1 DCD Data Carrier Detect

2 RXD Receive Data

3 TXD Transmit Data

4 DTR Data Terminal Ready

5 GND System Ground

6 DSR Data Set Ready

7 RTS Request to Send

8 CTS Clear to Send

9 RI Ring Indicator

2. RS-232 Mini-DIN 8-pin Port Definition

3. RS232 (DB9) Port Definition

4. VISCA networking as shown below:Camera Cascade Connection Method

Camera 1 Camera 2

1. DTR 1. DTR

2. DSR 2. DSR

3. TXD 3. TXD

4. GND 4. GND

5. RXD 5. RXD

6. GND 6. GND

7. IR OUT 7. OPEN

8. NC 8. OPEN

Note: OTTICA has RS232 input and output interface, so you can cascade as shown above.

- 14 -

3. Application Instructions

3.1 Remote Control

3.1.1 Keys Instruction

1. Standby Key After a 3-second long press, the camera will step into

standby mode. After pressing the standby key for 3 seconds again, the camera will self-test again and go back to the HOME position.

2. Camera Address Selection Select the camera address which wants to be controlled.3. Number Keys Set or run 0-9 presets.3. # + * Keys Use for key combinations.5. Focus Control Key Auto Focus: Enter into auto focus mode. Manual Focus: The camera focus mode is manual Switch the camera focus mode to manual focus by

pressing [focus +] or [focus -] to adjust.6. Zoom Control Key Zoom +: Zoom In. Zoom - :Zoom Out.7. Set or Clear Preset key: Set Preset: Sets preset key + 0-9 number key. Clear Preset: Clears preset key + 0-9 number key.8. Pan/Tilt Control Key Press Key: Tilts camera upwards. Press Key: Tilts camera downwards. Press Key: Pans camera left. Press Key: Pans camera right. “HOME” Key: Returns camera to the middle position. Also

used to enter into the next level menu.9. BLC Control Key Back Light ON / OFF: Turn on or off the back light.10. Menu Setting Open or close the on-screen-display menu. Enter / exit the on-screen-display menu or return to the

previous menu.

- 15 -

3.1.2 Applications

Camera Selection - Select the camera address to control.

11. Camera IR Remote Control Address Setting [ * ]+ [ # ]+[ F1 ] : Camera Address No. 1 [ * ]+ [ # ]+[ F2 ] : Camera Address No. 2 [ * ]+ [ # ]+[ F3 ] : Camera Address No. 3 [ * ]+ [ # ]+[ F4 ] : Camera Address No. 4

12. Key Combination Functions

Users can control the pan/tilt/zoom, settings and execute preset positions via the IR remote controller.

Key Instructions: - In these instructions, “press the key” means a click rather than a long-press. A special note

will be given if a long-press for more than one second is required. - When a key-combination is required, do it in sequence. For example, “[ * ] + [ # ] + [ F1 ]”

means press [ * ] first, then press [ # ], lastly press { F1 ]

[ # ] + [ # ] + [ # ]: Clear all presets [ * ] + [ # ] + [ 6 ]: Restore factory defaults

[ * ] + [ # ] + [ 9 ]: Flip switch [ * ] + [ # ] + Auto: Enter into the aging mode

[ * ] + [ # ] + [ 3 ]: Menu set to Chinese [ * ] + [ # ] + [ 4 ]: Menu set to English

[ * ] + [ # ] + Manual: Restore the default user name, password, and IP address

[ # ] + [ # ] + [ 0 ]:Switch video format to 1080p60


[ # ] + [ # ] + [ 2 ]:Switch video format to 1080i60

[ # ] + [ # ] + [ 3 ]:Switch video format to 1080i50







- 16 -

Preset Setting - To set a preset position, press the [ SET PRESET ]

key first and then press the number key 0-9 to set a relative preset.

- Note: 10 preset positions in total are available by remote controller.

Preset Running - Press a number key 0-9 directly to run a relative preset. - Note: Action will not be completed if a relative preset

position doesn’t exist.Preset Clearing - To clear a preset position, press the [CLEAR PRESET]

key first and then press the number key 0-9 to clear the relative preset.

- Note: press the [ # ] key three times to clear all presets.

BLC ON / OFF - Enables and/or disables backlight compensation

Focus Control - Focus (near):Press FOCUS + Key

(Valid only in manual focus mode) - Focus (far): Press FOCUS - Key

(Valid only in manual focus mode) - Pressing and holding the “+” or “–“ keys will result in

the action of focus to continue. Release the key to stop the action of focus.

- Auto Focus: Enables auto focus function. - Manual Focus: Enables manual focus function.

Zoom Control - ZOOM IN: Press Zoom + Key - ZOOM OUT: Press Zoom - Key - By pressing and holding the key, the camera lens will

keep zooming in or zooming out and stops as soon as the key is released.

Pan/Tilt Control Up: Press Down: Press Left: Press Right: Press - Back to middle position: Press HOME - Press and hold the up/down/left/right key to pan or

tilt the camera. The camera movement will ease from slow to fast until it reaches the endpoint. The pan/tilt movement stops as soon as the key is released.

- 17 -

Remote Controller Address Setting [ * ]+ [ # ]+[ F1 ] : Camera Address No. 1 [ * ]+ [ # ]+[ F2 ] : Camera Address No. 2 [ * ]+ [ # ]+[ F3 ] : Camera Address No. 3 [ * ]+ [ # ]+[ F4 ] : Camera Address No. 4

3.2 Menu Setting

3.2.1 Main Menu

3.2.2 System Settings

Protocol: VISCA / PELCO-P / PELCO-D/ AUTOVisca ADDR: VISCA = 1~7 PELCO-P = 1~255 PELCO-D = 1~255Visca Address Fix: ON / OFFBaud Rate: 2400 / 4800 / 9600 / 115200

In normal working mode, press the MENU key to display the menu. Use the scroll arrow to point at or highlight the selected items.

Move the arrow to the SETUP option in the Main Menu and click the HOME key to enter into the SETUP Settings Menu.

MENU========================Language English(Setup)(Camera)(P/T/Z)(Video Format)(Version)(Restore Default)

[ ] Select [ ] Change Value

SETUP========================Protocol AutoVisca Address 1Visca Address Fix OFFPELCO-P Address 1PELCO-D Address 0Baud Rate 9600


[ MENU ] Back: Press MENU to Return[ HOME } OK: Press HOME to ConfirmLanguage Setting: English / ChineseSetup: System SettingsCamera: Camera SettingsPTZ: Pan / Tilt / Zoom Settings

Version: Camera Version SettingsRestore Default: Reset Settings

[ ] Select: Menu Selection[ ] Change Value: Modify Parameters

- 18 -

3.2.3 Camera Settings

CAMERA========================(Exposure)(Color)(Image)(Focus)(Noise Reduction)


EXPOSURE========================Mode AutoEV OFFBLC OFFAnti-Flicker 50HzGain Limit 3WDR 5


Move the arrow to desired setting (Exposure, Color, etc.) option in the CAMERA menu and click the HOME key to enter.

1. EXPOSURE

- Mode: Auto / Manual / Shutter Priority / Iris Priority / Brightness Priotity - EV: ON / OFF (Only available in Auto mode) - Compensation Level: -7~7 (only available in auto mode when EV is ON) - BLC: ON/OFF for options (only available in auto mode) - Anti-Flicker: OFF/50Hz/60Hz for options (only available in Auto/Iris priority/Brightness priority modes)

Move the arrow to the CAMERA option in the Main Menu and click the HOME key to enter into the CAMERA Settings Menu.

- Gain Limit: 0~15(only available in Auto/ Iris Priority /Brightness Priority mode) - WDR: Off, 1~8 - Shutter Priority: 1/25, 1/30, 1/50, 1/60, 1/90, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/1000, 1/2000, 1/3000, 1/4000, 1/6000, 1/10000 (only available in Manual and Shutter priority mode) - IRIS Priority: OFF, F11.0, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.8 (only available in Manual and Iris priority mode) - Brightness: 0~23 (only available in Brightness Priority mode)

- 19 -

COLOR========================WB Mode AutoSaturation 80%Hue 7AWB Sensitivity HighColor Style DefaultColor Temp Low


FOCUS========================Focus Mode AutoAF-Zone CenterAF-Sensitivity Low


IMAGE========================Brightness 6Contrast 8Sharpness 7Flip-H OFFFlip-V OFFB&W-Mode ColorGamma DefaultDZoom OFFDCI Close


2. COLOR

- WB Mode: Auto, 3000K, 3500K, 4000K, 4500K, 5000K, 5500K, 6000K, 500K, 7000K, Manual, One Push - Red Gain: 0~255(only available in Manual mode) - Blue Gain: 0~255(only available in Manual mode) - Saturation: 60%, 70%, 80%, 90%, 100%, 110%, 120%, 130% - Hue: 0~14 - AWB Sensitivity: High/Middle/Low - Color Style: Default, style1~4 - Color Temp: High/Middle/Low

4. FOCUS

- Focus Mode: Auto, Manual - AF-Zone: Up, Middle, Down - AF-Sensitivity: High, M=Middle, Low

3. IMAGE

- Brightness: 0~14 - Contrast: 0~14 - Sharpness: 0~15 - Flip Horizontal: On/Off - Flip Vertical: On/Off - B&W Mode: Color, Black/White - Gamma: default, 0.47, 0.50, 0.52, 0.55 - Digital zoom options: On/Off - Dynamic Contrast: Off, 1~8

- 20 -

NOISE REDUCTION========================NR-2D AutoNR-3D 3Dynamic Hot Pixel OFF


P/T/Z========================Depth of Field ONZoom Speed 8Image Freezing OFFAcc Curve Slow


4. NOISE REDUCTION

- 2D Noise Reduction: Auto, Close, 1~7 - 3D Noise Reduction: Close, 1~8 - Dynamic Hot Pixel: Close, 1~5

- Depth of Field: Only effective for remote controller, On/Off; - When zoom in, the PT control speed by remoter will become slow), - Zoom Speed: Set the zoom speed for remote controller, 1~8 - Image Freezing: On/Off - Accelerating Curve: Fast/slow

- S Version: 1080P60, 1080P50, 1080P30, 1080P25, 1080I60, 1080I50, 720P60, 720P50, 720P30, 720P25, 1080P59.94, 1080I59.94, 1080P29.97, 720P59.94, 720P29.97 Optional - M Version: 1080P30, 1080P25, 1080I60, 1080I50, 720P60, 720P50 Optional

Notes: - S: 1080P60 Downward Compatibility - M: 1080P30 Downward Compatibility - Exiting the menu will save the modification of the parameter. Restart device for parameter modification to be enabled.

VIDEO FORMAT========================1080P60 1080P501080I60 1080I501080P30 1080P25720P60 720P50720P30 720P251080P59.94 1080I59.941080P29.97 720P59.94 720P29.97

[ ] Select [ Menu ] Back

3.2.4 P/T/Z

3.2.5 Video Format

Move the arrow to the P/T/Z option in the Main Menu and click the HOME key to enter into the P/T/Z Settings Menu.

Move the arrow to the VIDEO FORMAT option in the Main Menu and click the HOME key to enter into the VIDEO FORMAT Settings Menu.

- 21 -

RESTORE DEFAULT========================Restore Default? NO


VERSION========================MCU Version 2.0.0.15 2015-12-18Camera Version 2.0.0.13 2015-12-18

AF Version 2.0.0.6 2015-12-11Lens 12X (20X)

[ Menu ] Back

- MCU Version: Display MCU version information - Camera Version: Display camera version information - AF Version: Display the focus version information - Lens: Display the lens zoom

- Restore default: options: Yes/No; after restoring default, the video format won’t be restored. - Note: If the address of former remote is 2, 3, or 4, the corresponding camera address will restore to 1 when all parameters or system parameters are restored. User should change the remote address to be 1 (press No.1 according to the camera to get normal operation)

3.2.6 Version

3.2.6 Restore Default

Move the arrow to the VERSION option in the Main Menu and click the HOME key to enter into the VERSION Settings Menu.

Move the arrow to the RESTORE DEFAULT option in the Main Menu and click the HOME key to enter into the RESTORE DEFAULT Settings Menu.

- 22 -

4.1 Obtain Camera IP Address Based on Auto DHCP The OTTICA is set to Auto DHCP, so you’ll need to obtain camera IP address before connecting to a networtk. See 2 common solutions to obtain the camera IP address.

Solution 1:

1. Connect the camera to a device that can automatically assign an IP address, such as routers and switches.

2. Use an IP Search Tool to search LAN segment, such as “192.168.5.0~192.168.5.255”. We suggest using “SoftPerfect Network Scanner” software to get the search results.

3. Then search the results and refer to the MAC address pasted on the bottom of the camera to obtain the camera IP address.

Reference Image:

4. Network Connection

- 23 -

Solution 2:1. Connect the camera to devices that can automatically assign IP address, such as routers and

switches.2. Enter into the Management Interface of the router or switch and obtain the camera IP

address with reference to the MAC address pasted on the bottom of the camera.

Web Client Log In

4.2 IE Log In

4.2.1 Web Client

- Input the camera IP address (the IP address you obtain through Search Tool) in the address field of your browser and click the “Enter” button to proceed to the Web Client login page.

- 24 -

- You can login as the administrator and normal user. If logging in as an administrator, fill out the required fields with the following: Username: admin. Password: admin. - Administrator users can preview, playback, cancel, and configure in the Web Client; If logging in as a normal user, the default User name/Password is: user1 or user2. Normal users can only preview playback and cancel. There is no option for configuration. - NOTE: If you do not have the latest version of Flash installed, click on the button that says “Get ADOBE Flash Player. After you’ve installed the latest version of flash, the camera feed should be visible and you can now perform PTZ control, video recording, playback, configuration, and other operation

After successfully logging into the management interface, the video preview interface will become visible. In this interface, users can control pan, tilt, zoom, focus, video capture, sound, full screen, set the preset position, run, delete, and other operations.

Click Configuration to enter into the settings page.There are the following options: Audio Configuration, Video Configuration, Network Configuration, System Configuration.

- Switch: Choose to enable the audio or not. - Encoding Type: Set the audio compressing format and the device will reboo automatically after the change (default: MP3. optional: PCM & AAC). - Sample Rate: Set the sampling frequency and the device will reboot automatically after change (default: 48000. Optional: 16000, 32000 and 44100) - Sampling Bits: Set the sampling precision (Default: 16bits) - Bit Rate: Set the audio compressing code rate (Default: 64kbps; Optional: 32, 48, 96, 128kbps) - Channel: Set the audio channel (default: stereo. optional: mono) - Input Volume: Set the volume level (default: 2). Note: Click “SAVE” and it will remind” Enable has changed. Restart the device to take effect after the success of the save.”, then please reboot the camera to make new setting effect.

- Code stream: Stream: Different video output mode settings are available: Main Stream & - Secondary Stream - Compression Format: You can set the video compression format. Save and reboot to activate the new format (primary / secondary stream default is set to H.264. H.265 is optional). - Profile: Profile Mode Setting (default is set to HP. BP & MP are optional). - Video Size: You can set the video image resolution. Save and reboot to activate the new

4.2.2 Preview

4.2.3 Configuration

4.2.4 Audio Configuration

4.2.5 Video Configuration

1. Video Encoding

- 25 -

format (main stream default: 1080p. 720p is optional). - Stream Rate control: You can set the rate control mode. Save and reboot to activate the new mode (primary / secondary stream default is set to Variable Rate. Fixed rate is optional). - Image Quality: You can set the image quality. The image quality can be changed only when the stream rate control is set to Variable Rate. - Bit Rate (Kb/s): You can set the video bit rate (Main stream default: 4096kb/s. Optional: 64-12288kb/s) (Secondary stream default: 1024kb/s. Optional: 64-10240kb/s) - Frame Rate (fps): Set the video frame rate (primary / secondary stream default is 25fps. primary stream 5-60fps is optional, secondary stream 5-30fps is optional). - Frame Interval: You can set the key frame interval (primary / secondary stream default setting is 75f. Primary / stream 1-300f is optional. Secondary stream 1-150F is optional). - Stream Name: When streaming via rtsp or rtmp, you can modify the stream name. Main Stream (live/av0), sub stream (live/av1) - Click the “Save” button to display the “saved successfully” message. The new settings will then be activated. - Switch: To turn on/off the main / secondary stream. - Protocol: Primary / secondary stream applies RTMP protocol. - Host Port: Server port number (Default: 1935; Optional: 0-65535) Host Address: Server IP addresses (Default: 192.168.5.11) - Stream Name: Choose a different stream name (live / av0, live / av1 optional). - User: Set the user name.

- Switch: To turn on/off the main / sub stream. - Protocol Type: Primary / secondary stream applies RTMP protocol. - Host Address: Server IP addresses (Default: 192.168.5.11) - Host Port: Server port number (Default 1935: Optional: 0-65535) - Stream Name: Choose a different stream name (live / av0, live / av1 optional). - User Name: Set the user name. - Password: Set the password. - Click on the “Save” button to display the “Save successful” message. The new settings will then be activated. - Method of obtaining RTSP: rtsp: // device IP address: 554 / live / av0 (av0 main stream; av1 secondary stream).

- Switch: To turn on/off the main / sub stream. - Protocol Type: RTP or TS - Multicast Address: Default 224.1.2.3. (Can be edited) - Multicast Port: Main Stream Default Port: 4000, Sub Stream Default Port: 4002

2. Stream Publish

3. Multicast

- 26 -

4. Video Parameters

A. Focus Settings

B. Exposure

C. Color

D. Image

- Focus Mode: Auto (default), Manual & OnePush (optional).- AF-Zone: All (default), Top, Center, Bottom (optional).- Focus Sensitivity: Low (default), High & Medium (optional).

- White Balance Modes: (Default: Automatic; Optional: Manual, OnePush, Variable)- Variable Color Temperatures: 2400K - 7100K- Red Gain: (Default: 255; Optional: 0-255).- Blue Gain: (Default: 199; Optional: 0-255).- Saturation: (Default: 100%; Optional: 60%, 70%, 80%, 90%, 110%, 120%, 130%).- Hue: (Default: 7; Optional: 0-14).- Auto White Balance Sensitivity: (Default: High; Optional: Low & Medium)

- Brightness: (Default: 6; Optional: 0-14).- Contrast: (Default: 8; Optional: 0-14).- Sharpness: (Default: 7; Optional: 0-15).- Black and White Mode: (Default: Color; Optional: Black &White).- Gamma: (Default: 0.45; Optional: 0.50, 0.52, 0.55).- Flip Horizontal: (Default: OFF; Optional: ON).

- Mode: Auto (default), Manual, SAE, AAE, Bright (optional). Shutter Priority, Aperture Priority, Brightness Priority (optional). - Exposure Compensation: Exposure Compensation settings are activated only when - EV: Off (default), On (optional) - EV Level: 0 (default) -7 through 7 (optional) - BLC: Settings are activated only when Exposure Mode is set to Automatic (Default: OFF). - Flicker: Settings are activated only when Exposure Mode is set to Automatic, Aperture, or Brightness Priority. (Default: 50Hz. Optional: Off & 60Hz). - Gain Limit: (Default: 3; Optional: 0-15). - Dynamic Range: (Default: 4; Optional: 0-8). - Shutter Speed: Settings are activated only when Exposure Mode is set to Manual or Shutter-Priority (Default:1/100. Optional: 1/25, 1/30, 1/50, 1/60, 1/90, 1/100, 1/120, 1/180, 1/250, 1/350, 1/500, 1/1000, 1/2000, 1/3000, 1/4000, 1/6000, 1/10000). - Iris: Settings are activated only when Exposure Mode is set to Manual or Aperture-Priority (Default: F1.8; Optional: Closed, F1, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.8). - Brightness: Settings are activated only when Exposure Mode is set to Brightness Priority (Default: 7; Optional: 0-23).

- 27 -

4. Character-Overlapping

5. Character Size

E. Noise Reduction

F. Style

- 2D Noise Reduction: (Default: 1; Optional: 2-7, AUTO, and OFF).- 3D Noise Reduction: (Default: 3; Optional: 1-8 and OFF).- Dynamic Dead Pixel Correction: (Default: OFF; Optional: 1-5).

- Style Option: (Default: Default; Optional: Normal, Clarity, Bright, Soft)

- Display Date and Time: Set whether to display the time and date (default display).- Display Title: Set whether to display the title (default display).- Font Color of Time: (Default: White; Optional: Black, Yellow, Red, Blue).- Font Color of Title: (Default: White; Optional: Black, Yellow, Red, Blue).- Moving Characters: You can set the display position of moving date, time and title, clickon the “Up, Down, Left, Right” buttons to move the corresponding character position.- Title Content: You can set Title Content (default is set to CAMERA1).- Time Content: You can set Time Content (default is set to 1970/01/10 05:36:00).- After clicking on the “Save” button, the “Save Successful” message will be displayed.Your selected time settings will now be visible.

- Switch: Enable “Scale Size Automatically” funtion.- Master Stream OSD Font Size: Set the character size of the display, the device will

restart automatically after changed and saved (Default: 48).- Slave Stream OSD Font Size: You can set the Character Size on the display. The device

will restart automatically after changed and saved (Default: 48).- After clicking on the “Save” button, the configuration will be validated when you see the

“Parameter Saved Successfully” message displayed.

- Flip Vertical: (Default: OFF; Optional: ON).- DCI: (Default: OFF; Optional: ON).- DZoom: (Default: OFF; Optional: ON).- Low-Light Mode: (Default: OFF; Optional: ON).

6. Video Output

- Default: 1080P29.97- Optional: 1080P60, 1080P50, 1080P30, 1080P25, 1080I60, 1080I50, 720P60,

720P50, 720P30, 720P25, 1080P59.94, 1080I59.94, 720P59.94, 720P29.97- By clicking on the “Save” button, the configuration will be validated when you see the

“Save successful” message displayed.

- 28 -

1. Network Port

2. Ethernet Parameters

3. DNS Parameters

- Data port: You can set the Data Port. The device will restart automatically after it’s changed (Default: 3000; Optional: 0-65535).

- Web Port: You can set the Web Port. The device will restart automatically after changed (Default: 80; Optional: 0-65535).

- Onvif Port: You can set the Onvif Port. The device will restart automatically after changed (Default: 2000; Optional: 0-65535).

- Soap Port: You can set the Soap Port (Default: 1936; Optional: 0-65535).- RTMP Port: You can set the RTMP Port (Default: 1935; Optional: 0-65535).- RTSP Port: You can set the RTSP Port. The device will restart automatically after

changed (Default: 554; Optional: 0-65535).- Visca Port: You can set the Visca Port. The device will restart automatically after

changed (Default: 1259; Optional: 0-65535).- By clicking on the “Save” button, the configuration will be validated when you see the

display message: “Save successful”.- RTMP access: RTMP: / / equipment IP address: 1935 / live/av0 (av0 main stream; av1

second stream)- RTMP Access: rtmp://equipment IP address: 1935 / live/av0 (av0 main stream; av1

second stream)

- DHCP: Enable or disable the option to obtain IP automatically can be set. By clicking on the “Save” button and rebooting the device, a display saying “Save successful” will be shown. The configuration will now be validated ( Default is set to ON).

- IP Address: You can set the IP Address. By clicking on the “Save” button and rebooting the device, a display saying “Save successful” will be shown. The configuration will now be validated. (Default is now set to 192.168.5.163). Note: This IP address is the same with the one used to login to the web page.

- Subnet Mask: You can set the Subnet Mask (Default is set to 255.255.255.0).- Default Gateway: You can set the Default Gateway (Default is set to 0.0.0.0).- MAC Address: You can set the Physical Address (The parameter is read-only and can

not be modified).- By clicking on the “Save” button, the configuration will be validated when you see the

display message: “Save successful”.

4.2.6 Network Configuration

- Preferred DNS Server: You can set the preferred DNS server (Default is set to 0.0.0.0).- Alternate DNS Server: Alternate DNS server settings (Default is set to 0.0.0.0).- By clicking on the “Save” button, the configuration will be validated when you see the


- 29 -

4. NDI

- Switch: Set NDI funcion on or off. NDI Name: User can change the NDI Name NDI Group: User can change the NDI Group

- By clicking on the “Save” button, the configuration will be validated when you see the display message: “Save successful”.

1. System Attributes

- Device Name: Set the device name (Default is CAMERA-1. User can create their own).- Device ID: Set the device ID (default is set to 1. Read-Only).- System Language: Set the system language (Default: English; Optional: Simplified

Chinese). Re-login after modification and save the setting.- By clicking on the “Save” button, the configuration will be validated when you see the

display message: “Save successful”

4.2.7 System Configuration

2. System Time

- Date Format: You can set the Date Format (YYYY-MM-DD).- Date Separator: (Default: “/” Optional: “.” and “-”).- Time Zone: You can set the Time Zone.- Hour Type: (Default: 24 hours; Optional: 12 hours).- NTP Enable: Click the checkbox to turn the “NTP Enable” function on or off.- Update Interval: You can set the NTP server to automatically update the time interval. Valid

after setting NTP server synchronization (Default: One Day; Optional: 2-10 days).- Host URL: You can set NTP server address or domain name (default time.nits.gov). Valid

after setting NTP server synchronization.- Host Port: You can set the NTP server port (Default: 123). Valid after setting NTP server

synchronization.- Set the time manually. Effective when set manually.- Time Setting: You can set the Time Mode (choose the computer time synchronization, NTP

server time synchronization, or set manually).- Computer Time: You can set the Computer Time.- By clicking on the “Save” button, the configuration will be validated when you see the


- 30 -

3. User Settings

4. Version Upgrade

5. Restore Factory Setting

6. Reboot

- Authority: You can set the User Type (the default is set to Administrator. Common User 1, Common User 2 are optional)

- User name: You can set the User Name (Select User Administrator default admin; select a common user1 default user1; to select a common user 2 default user2; user can modify their own)

- Password: You can set a Password (Select User Administrator default admin; select a common user1 default user1; to select a common user 2 default user2; user can modify their own).

- Password Confirmation: Confirm the input passwords are the identical.- By clicking on the “Save” button, the configuration will be validated when you see the

display message: “Save successful”.- Note: User name and Password are case-sensitive.

MCU version V2.0.0.16 2015-12-18 Camera version V2.0.0.16 2015-12-18 Focus version V2.0.0.6 2015-12-11.Update File:- Click “Browse ...” installation, to select the upgrade file in the pop-up window.- Click on the “Upgrade” button. The upgrade dialog will appear. The device will reboot

automatically after the update is successful. Make sure the power and network remains connected during the upgrading process.

- Note: If you need to restore factory defaults, choose one of the three options: A. Through web to restore the factory default configuration. B. Through the recovery menu. C. Remote control shortcut: * # 6.

- Click on “Restore Factory Defaults” button and choose “yes” or “no”, then the device will restart automatically and restore factory setting.

- Click on the “Reboot” button and choose “yes” or “no”.- The device will restart automatically.

- 31 -

1. Network Settings

Wireless Network Configuration- Enable Network Interface: You can check, to set the following items after checked.- DHCP: If checked, it can obtain IP automatically.- IP address: set wireless WIFI IP (default is set to 192.168.1.250. If checked DHCP, IP will

be assigned automatically). Note: Wireless IP address cannot be in the same segment with wired IP address.- Subnet Mask: You can set the wireless IP subnet mask (Default: 255.255.255.0)- Default Gateway: You can set the wireless IP default gateway (Default: 192.168.1.1)- SSID: The user can modify their own (the default test).- Encryption: Able to be checked. The password can be set after checked.- Password: You can set the password. Password can be changed only if encryption is

checked. After clicking on the “Save” button, character settings will be validated when the

“Parameter Saved Successfully” message is displayed. Note: SSID and password should be filled in correctly; otherwise, if restarted after powered

off, the wireless Wi-Fi connection will not be successful.

Click “Logout.” When the pop-up “Confirmation” dialog appears, select “Yes” or “No”. Choose “Yes” to exit the current page and return to the user login interface again.

If the user’s equipment has a wireless network module, the web page “Network Configuration” has a “Wireless Network” configuration page. The specific configuration is as follows:

4.2.8 Logout

4.2.9 Wireless Network

2. Wi-Fi Hot Link

- Click on the “search” button to search the WIFI hotspot.- Double-click the dialog box after you’ve searched the user WIFI hotspot. Then input

password to connect to WIFI. It will connect successfully after showing the “Successful Connect” window.

3. Wireless Wi-Fi Login Page

- If you do not check the above DHCP configuration (automatically obtain IP), then open the browser, enter the wireless network IP address in the address bar (Default: 192.168.1.250), press Enter to log construction.

- If you checked DHCP, then you will obtain IP automatically, just login specific router or switch user interface settings to view the allocation of IP address.

- 32 -

5.1.1 Camera Return Command

Under common working condition, the camera could be controlled through RS232/RS485 interface (VISCA), RS232C serial parameter are as follows:Baud rate: 2400/4800/9600/115200 bits / sec; Start bit: 1; data bits: 8; Stop bit: 1; Parity: None.

5.1 VISCA Protocol List

5. Serial Communication Control

ACK/Completion Message

Command Packet Note

ACK z0 41 FF Returned when the command is accepted.

Completion z0 51 FF Returned when the command has been executed.

Error Messages

Command Packet Note

Syntax Error z0 60 02 FF Returned when the command format is different or when a command with illegal command parameters is accepted

Command Not Executable

z0 61 41 FF Returned when a command cannot be executed due to current conditions. For example,when commands controlling the focus manually are received during auto focus.

- 33 -

5.1.2 Camera Control Command

Command Function Command Packet Notes

AddressSet Broadcast 88 30 0p FF p: Address setting

IF_Clear Broadcast 88 01 00 01 FF I/F Clear

CommandCancel 8x 21 FF

CAM_PowerOn 8x 01 04 00 02 FF

Power ON/OFFOff 8x 01 04 00 03 FF

CAM_Zoom

Stop 8x 01 04 07 00 FF

Tele(Standard) 8x 01 04 07 02 FF

Wide(Standard) 8x 01 04 07 03 FF

Tele(Variable) 8x 01 04 07 2p FFp = 0(low) - F(high)

Wide(Variable) 8x 01 04 07 3p FF

Direct8x 01 04 47 0p 0q 0r 0s FF

pqrs: Zoom Position

CAM _Focus

Stop 8x 01 04 08 00 FF

Far(Standard) 8x 01 04 08 02 FF

Near(Standard) 8x 01 04 08 03 FF

Far(Variable) 8x 01 04 08 2p FF p = 0(low) - F(high)

Near (Variable) 8x 01 04 08 3p FF

Direct8x 01 04 48 0p 0q 0r 0s FF

pqrs: Focus Position

Auto Focus 8x 01 04 38 02 FF

One Push Mode

8x 01 04 38 04 FF

Manual Focus 8x 01 04 38 03 FF

CAM _Zoom Focus Direct8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF

pqrs: Zoom Positiontuvw: Focus Position

CAM_WB

Auto 8x 01 04 35 00 FF

3000K 8x 01 04 35 01 FF

4000k 8x 01 04 35 02 FF

One Push Mode

8x 01 04 35 03 FF

5000k 8x 01 04 35 04 FF

- 34 -


CAM-WB(continued)

Manual 8x 01 04 35 05 FF

6500k 8x 01 04 35 06 FF

3500K 8x 01 04 35 07 FF

4500K 8x 01 04 35 08 FF

5500K 8x 01 04 35 09 FF

6000K 8x 01 04 35 0A FF

7000K 8x 01 04 35 0B FF

CAM _RGain

Reset 8x 01 04 03 00 FF

Manual Control of R GainUp 8x 01 04 03 02 FF

Down 8x 01 04 03 03 FF

Direct8x 01 04 43 00 00 0p 0q FF

pq: R Gain

CAM_ Bgain

Reset 8x 01 04 04 00 FF

Manual Control of B GainUp 8x 01 04 04 02 FF

Down 8x 01 04 04 03 FF

Direct8x 01 04 44 00 00 0p 0q FF

pq: B Gain

CAM_AE

Full Auto 8x 01 04 39 00 FF Automatic Exposure mode

Manual 8x 01 04 39 03 FF Manual Control mode

Shutter priority 8x 01 04 39 0A FFShutter Priority Automatic Exposure mode

Iris Priority 8x 01 04 39 0B FFIris Priority Automatic Exposure mode

Bright 8x 01 04 39 0D FF Bright mode

CAM_Shutter

Reset 8x 01 04 0A 00 FF

Shutter SettingUp 8x 01 04 0A 02 FF

Down 8x 01 04 0A 03 FF

Direct8x 01 04 4A 00 00 0p 0q FF

pq: Shutter Position

CAM_Iris

Reset 8x 01 04 0B 00 FF

Iris SettingUp 8x 01 04 0B 02 FF

Down 8x 01 04 0B 03 FF

Direct8x 01 04 4B 00 00 0p 0q FF

pq: Iris Position

CAM_Gain Limit Gain Limit 8x 01 04 2C 0p FF p: Gain Positon

- 35 -


CAM_Bright

Reset 8x 01 04 0D 00 FF

Bright SettingUp 8x 01 04 0D 02 FF

Down 8x 01 04 0D 03 FF

Direct8x 01 04 4D 00 00 0p 0q FF

pq: Bright Positon

CAM_ExpComp

On 8x 01 04 3E 02 FF Exposure Compensation ON/OFFOff 8x 01 04 3E 03 FF

Reset 8x 01 04 0E 00 FFExposure Compensation Amount Setting

Up 8x 01 04 0E 02 FF

Down 8x 01 04 0E 03 FF

Direct8x 01 04 4E 00 00 0p 0q FF

pq: ExpComp Position

CAM_Back LightOn 8x 01 04 33 02 FF

Back Light CompensationOff 8x 01 04 33 03 FF

CAM_WDRStrength

Reset 8x 01 04 21 00 FF

WDR Level SettingUp 8x 01 04 21 02 FF

Down 8x 01 04 21 03 FF

Direct8x 01 04 51 00 00 00 0p FF

p: WDR Level Positon

CAM_NR (2D) 8x 01 04 53 0p FF P=0-7 0:OFF

CAM_NR (3D) 8x 01 04 54 0p FF P=0-8 0:OFF

CAM_Gamma 8x 01 04 5B 0p FF

p = 0 – 4 0: Default 1: 0.47 2: 0.50 3: 0.52 4: 0.55

CAM_Flicker

OFF 8x 01 04 23 00 FF OFF

50HZ 8x 01 04 23 01 FF 50HZ

60HZ 8x 01 04 23 02 FF 60HZ

CAM_Aperture

Reset 8x 01 04 02 00 FF

Aperture ControlUp 8x 01 04 02 02 FF

Down 8x 01 04 02 03 FF

Direct8x 01 04 42 00 00 0p 0q FF

pq: Aperture Gain

- 36 -


CAM_Memory

Reset 8x 01 04 3F 00 pq FF pq: Memory Number(=0 to 254)Corresponds to 0 to 9 on the Remote Commander

Set 8x 01 04 3F 01 pq FF

Recall 8x 01 04 3F 02 pq FF

CAM_LR_ReverseOn 8x 01 04 61 02 FF Image Flip Horizontal ON/

OFFOff 8x 01 04 61 03 FF

CAM_PictureFlipOn 8x 01 04 66 02 FF

Image Flip Vertical ON/OFFOff 8x 01 04 66 03 FF

CAM_ColorSaturation Direct8x 01 04 49 00 00 00 0p FF

P=0-70:60% 1:70% 2:80% 3:90% 4:100% 5:110% 6:120% 7:130%

CAM_IDWrite8x 01 04 22 0p 0q 0r 0s FF

pqrs: Camera ID (=0000 to FFFF)

SYS_MenuON 8x 01 04 06 06 02 FF Turn on the menu screen

OFF 8x 01 04 06 06 03 FF Turn off the menu screen

IR_ReceiveON 8x 01 06 08 02 FF IR (remote commander)

receive On/Off OFF 8x 01 06 08 03 FF

IR_ReceiveReturnOn

8x 01 7D 01 03 00 00 FF

IR(remote commander)receive message via the VISCA communication ON/OFFOff

8x 01 7D 01 13 00 00 FF

CAM_SettingvReset Reset 8x 01 04 A0 10 FF Reset Factory Setting

CAM_Brightness Direct8x 01 04 A1 00 00 0p 0q FF

pq: Brightness Position

CAM_Contrast Direct8x 01 04 A2 00 00 0p 0q FF

pq: Contrast Position

CAM_Flip

OFF 8x 01 04 A4 00 FF

Single Command For Video Flip

Flip-H 8x 01 04 A4 01 FF

Flip-V 8x 01 04 A4 02 FF

Flip-HV 8x 01 04 A4 03 FF

- 37 -


CAM_VideoSystemSet camera video system

8x 01 06 35 00 0p FF

P: 0~E Video Format0:1080P60 5:720P501:1080P50 6:1080P302:1080i60 7:1080P253:1080i50 8:720P304:720P60 9:720P25

A: 1080P59.94B: 1080i59.94C: 720P59.94D: 1080P29.97E: 720P29.97

Pan_tiltDrive

Up8x 01 06 01 VV WW 03 01 FF

VV: Pan speed0x01 (low speed) to0x18 (high speed)

WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)

YYYY: Pan Position

ZZZZ: Tilt Position

Down8x 01 06 01 VV WW 03 02 FF

Left8x 01 06 01 VV WW 01 03 FF

Right8x 01 06 01 VV WW 02 03 FF

Upleft8x 01 06 01 VV WW 01 01 FF

Upright8x 01 06 01 VV WW 02 01 FF

DownLeft8x 01 06 01 VV WW 01 02 FF

DownRight8x 01 06 01 VV WW 02 02 FF

Stop8x 01 06 01 VV WW 03 03 FF

AbsolutePo-sition

8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

RelativePosition8x 01 06 03 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

Home 8x 01 06 04 FF

Reset 8x 01 06 05 FF

- 38 -


Pan-tiltLimitSet

Set8x 01 06 07 00 0W 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

W:1 UpRight 0:DownLeft

YYYY: Pan Limit Posi-tion(TBD)

ZZZZ: Tilt Limit Position(TBD)

Clear8x 01 06 07 01 0W 07 0F 0F 0F 07 0F 0F 0F FF


CAM_PowerInq 8x 09 04 00 FFy0 50 02 FF On

y0 50 03 FF Off(Standby)

CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position

CAM_FocusAFModeInq 8x 09 04 38 FF

y0 50 02 FF Auto Focus

y0 50 03 FF Manual Focus

y0 50 04 FF One Push Mode

CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position

CAM_WBModeInq 8x 09 04 35 FF

y0 50 00 FF Auto

y0 50 01 FF 3000K

y0 50 02 FF 4000K

y0 50 03 FF One Push Mode

y0 50 04 FF 5000K

y0 50 05 FF Manual

y0 50 00 FF 6500K

y0 50 06 FF 6500K

y0 50 07 FF 3500K

y0 50 08 FF 4500K

y0 50 09 FF 5500K

y0 50 0A FF 6000K

y0 50 0B FF 7000K

CAM_RGainInq 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq: R Gain

CAM_BGainInq 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq: B Gain

5.1.3 Inquiry Command

- 39 -


CAM_AEModeInq 8x 09 04 39 FF

y0 50 00 FF Full Auto

y0 50 03 FF Manual

y0 50 0A FF Shutter Priority

y0 50 0B FF Iris Priority

y0 50 0D FF Bright

CAM_ShutterPosInq8x 09 04 4A FF

y0 50 00 00 0p 0q FF pq: Shutter Position

CAM_IrisPosInq8x 09 04 4B FF

y0 50 00 00 0p 0q FF pq: Iris Position

CAM_Gain LimitInq8x 09 04 2C FF

y0 50 0p FF p: Gain Positon

CAM_ BrightPosiInq8x 09 04 4D FF

y0 50 00 00 0p 0q FF pq: Bright Position

CAM_ExpCompModeInq 8x 09 04 3E FFy0 50 02 FF On

y0 50 03 FF Off

CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Position

CAM_BacklightModeInq 8x 09 04 33 FFy0 50 02 FF On

y0 50 03 FF Off

CAM_WDRStrengthInq 8x 09 04 51 FF y0 50 00 00 00 0p FF p: WDR Strength

CAM_NRLevel(2D) Inq 8x 09 04 53 FF y0 50 0p FF P: 2DNRLevel

CAM_NRLevel(3D) Inq 8x 09 04 54 FF y0 50 0p FF P:3D NRLevel

CAM_FlickerModeInq 8x 09 04 55 FF y0 50 0p FFp: Flicker Settings(0: OFF,1: 50Hz,2:60Hz)

CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF pq: Aperture Gain

CAM_PictureEffectModeInq 8x 09 04 63 FFy0 50 00 FF Off

y0 50 04 FF B&W

CAM_MemoryInq 8x 09 04 3F FF y0 50 0p FFp: Memory number last operated.

SYS_MenuModeInq 8x 09 06 06 FFy0 50 02 FF On

y0 50 03 FF Off

CAM_LR_ReverseInq 8x 09 04 61 FFy0 50 02 FF On

y0 50 03 FF Off

CAM_PictureFlipInq 8x 09 04 66 FFy0 50 02 FF On

y0 50 03 FF Off

- 40 -


CAM_ColorSaturationInq 8x 09 04 49 FF y0 50 00 00 00 0p FFp: Color Gain setting 0h (60%) to Eh (130%)

CAM_IDInq 8x 09 04 22 FF y0 50 0p FF p: Gamma ID

IR_ReceiveInq 8x 09 06 08 FFy0 50 02 FF On

y0 50 03 FF Off

IR_ReceiveReturn

y0 07 7D 01 04 00 FF Power ON/OFF

y0 07 7D 01 04 07 FF Zoom tele/wide

y0 07 7D 01 04 38 FF AF ON/OFF

y0 07 7D 01 04 33 FF Camera _Backlight

y0 07 7D 01 04 3F FF Camera _Memery

y0 07 7D 01 06 01 FF Pan_titleDriver

CAM_BrightnessInq 8x 09 04 A1 FF y0 50 00 00 0p 0q FFpq: Brightness Position

CAM_ContrastInq 8x 09 04 A2 FF y0 50 00 00 0p 0q FF pq: Contrast Position

CAM_FlipInq 8x 09 04 A4 FF

y0 50 00 FF Off

y0 50 01 FF Flip-H

y0 50 02 FF Flip-V

y0 50 03 FF Flip-HV

CAM_GammaInq8x 09 04 5B FF

y0 50 0p FF p: Gamma setting

CAM_VersionInq 8x 09 00 02 FFy0 50 ab cd mn pq rs tu vw FF

ab cd: - vendor ID ( 0220)mn pq: - model ID ST (0950) U3 (3950)rs tu:- ARM Versionvw:- Reserve

- 41 -


VideoSystemInq 8x 09 06 23 FF y0 50 0p FF

P: 0~E Video format0:1080P601:1080P502:1080i603:1080i504:720P605:720P506:1080P307:1080P258:720P309:720P25A: 1080P59.94B: 1080i59.94C: 720P59.94D: 1080P29.97E: 720P29.97

Pan-tiltMaxSpeedInq 8x 09 06 11 FF y0 50 ww zz FFww: Pan Max Speedzz: Tilt Max Speed

Pan-tiltPosInq 8x 09 06 12 FFy0 50 0w 0w 0w 0w0z 0z 0z 0z FF

wwww: Pan Positionzzzz: Tilt Position

Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7

Up 0xFF Address 0x00 0x08 Pan Speed Tilt Speed SUM

Down 0xFF Address 0x00 0x10 Pan Speed Tilt Speed SUM

Left 0xFF Address 0x00 0x04 Pan Speed Tilt Speed SUM

Right 0xFF Address 0x00 0x02 Pan Speed Tilt Speed SUM

Upleft 0xFF Address 0x00 0x0C Pan Speed Tilt Speed SUM

Upright 0xFF Address 0x00 0x0A Pan Speed Tilt Speed SUM

DownLeft 0xFF Address 0x00 0x14 Pan Speed Tilt Speed SUM

DownRight 0xFF Address 0x00 0x12 Pan Speed Tilt Speed SUM

Zoom In 0xFF Address 0x00 0x20 0x00 0x00 SUM

Zoom Out 0xFF Address 0x00 0x40 0x00 0x00 SUM

Focus Far 0xFF Address 0x00 0x80 0x00 0x00 SUM

Focus Near 0xFF Address 0x01 0x00 0x00 0x00 SUM

5.2 Pelco-D Protocol Command List

- 42 -

Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7

Set Preset 0xFF Address 0x00 0x03 0x00 Preset ID SUM

Clear Preset 0xFF Address 0x00 0x05 0x00 Preset ID SUM

Call Preset 0xFF Address 0x00 0x07 0x00 Preset ID SUM

Query Pan Position

0xFF Address 0x00 0x51 0x00 0x00 SUM

Query Pan Position Response

0xFF Address 0x00 0x59Value High Byte

Value Low Byte

SUM

Query Tilt Position


Query Tilt Position Response

0xFF Address 0x00 0x5BValue High Byte

Value Low Byte

SUM

Query Zoom Position


Query Zoom Position Response

0xFF Address 0x00 0x5DValue High Byte

Value Low Byte

SUM

Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8

Up 0xA0 Address 0x00 0x08 Pan Speed Tilt Speed 0xAF XOR

Down 0xA0 Address 0x00 0x10 Pan Speed Tilt Speed 0xAF XOR

Left 0xA0 Address 0x00 0x04 Pan Speed Tilt Speed 0xAF XOR

Right 0xA0 Address 0x00 0x02 Pan Speed Tilt Speed 0xAF XOR

Upleft 0xA0 Address 0x00 0x0C Pan Speed Tilt Speed 0xAF XOR

Upright 0xA0 Address 0x00 0x0A Pan Speed Tilt Speed 0xAF XOR

DownLeft 0xA0 Address 0x00 0x14 Pan Speed Tilt Speed 0xAF XOR

DownRight 0xA0 Address 0x00 0x12 Pan Speed Tilt Speed 0xAF XOR

Zoom In 0xA0 Address 0x00 0x20 0x00 0x00 0xAF XOR

Zoom Out 0xA0 Address 0x00 0x40 0x00 0x00 0xAF XOR

Focus Far 0xA0 Address 0x01 0x00 0x00 0x00 0xAF XOR

Focus Near 0xA0 Address 0x02 0x00 0x00 0x00 0xAF XOR

5.3 Pelco-P Protocol Command List

- 43 -

Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8

Set Preset 0xA0 Address 0x00 0x03 0x00 Preset ID 0xAF XOR

Clear Preset 0xA0 Address 0x00 0x05 0x00 Preset ID 0xAF XOR

Call Preset 0xA0 Address 0x00 0x07 0x00 Preset ID 0xAF XOR

Query Pan Position

0xA0 Address 0x00 0x51 0x00 0x00 0xAF XOR

Query Pan Position Response

0xA0 Address 0x00 0x59Value High Byte

Value Low Byte

0xAF XOR

Query Tilt Position


Query Tilt Position Response

0xA0 Address 0x00 0x5BValue High Byte

Value Low Byte

0xAF XOR

Query Zoom Position


Query Zoom Position Response

0xA0 Address 0x00 0x5DValue High Byte

Value Low Byte

0xAF XOR

6.1 Camera Maintenance

6.2 Troubleshooting

6. Camera Maintenance and Troubleshooting

1. No Video Output

1. If the camera hasn’t been used for long time, please turn off the power adapter switch and AC plug.

2. Use a soft cloth or tissue to clean the camera cover.3. Use soft cloth to clean the lens. Do not use strong or corrosive cleanser and avoiding

scuffing.

A. Check whether the camera power supply is connected, that the voltage is normal, and that the power indicator is lit.

B. Check to see if the camera performs the self-inspection after restarted. C. Check whether the bottom of the DIP switch is in the normal operating mode (see Table

2.2 pg 12)D. Check whether the video output cable or video display is normal.

- 44 -

2. Image Dithering When Zooming In or Out

3. Remote Controller Not Working

4. Serial Port Cannot Work

A. Check whether the camera installation position is solid.B. Whether there is shaking machine or objects around the camera.

A. The remote control address could be set to 1 (if the has been set back to the factory defaults, the remote control addresses need to be set back to 1 also).

B. Check if the batteries are low or if they are installed properly in the remote controller.C. Check if the camera working mode is the normal operating mode (see Table 2.2 pg 12).D. Check whether the menu is closed. Camera control through the remote controller is only

available after exiting the menu. If video is being output from LAN, the menu will not be displayed. After the menu automatically exists 30 seconds later, it can be controlled by remote controller.

A. Check if the camera serial device protocol, baud rate, and address are all consistent.B. Check if the control cable is connected properly.C. Check if the camera working mode is in the normal operating mode (see Table 2.2 pg 12)

- 1 -

OTT-CONTROLLERManual

OTTICA IP PTZ Camera Controller VISCA, ONVIF, PELCO

www.ikancorp.com [email protected]

- 2 -

1. What is the function of CAM NUM when adding a network device?

CAM NUM will be associated and bound with the currently entered IP and port information. It will quickly switch to the CAM NUM bound device when adding a device with the “CAM” button.

2. How do I enter an IP address?

The camera controller doesn’t have a “.” button, so please enter the IP address with four segments.

Take the IP address 192.168.0.1 for example. It will automatically jump to next segment when finished inputting a segment with three numbers, 192 and 168; but after inputting a segment with only one number, 0, you must move the joystick rightward to switch over to the next segment to continue inputting.

3. How do I clear while in input mode?

Move the joystick leftward to clear the input information.

4. The home page of each mode refers to the displayed page when the controller initialization is complete.

In IP VISCA and ONVIF Mode, if you see the prompts of “Visca!” and “Onvif!”, the IP address displayed on the screen is local IP address of the controller. While the prompts of “Visca:” and “Onvif:” are shown on the page, the IP address displayed on-screen belongs to the connected device.

Precautions

- 3 -

Precautions 21. Product Overview 4 1.1 Product Features 4 1.2 Wiring Diagram 4 1.3 Technical Specifications 52. Function Description 5 2.1 Button Description 5 2.2 Rocker Switch and Knob 7 2.3 Joystick Control 7 2.4 Terminal Description of Back Panel Interfaces 83. Local Settings (SETUP) 8 3.1 Basic Settings 8 3.2 VISCA & IP VISCA Mode Shared Setting 9 3.3 IP VISCA Mode Setting 9 3.4 VISCA Mode Setting 9 3.5 PELCO Mode Setting 9 3.6 ONVIF Mode Setting 104. Connection and Control 10 4.1 Connection and Control in ONVIF Mode 10 4.2 Connection and Control in IP VISCA Mode 11

4.3 Control in VISCA & PELCO Mode 115. Web Page Configuration 11 5.1 Home Page 11 5.2 LAN Settings 12 5.3 Upgrade 13 5.4 Restore Factory 13 5.5 Reboot 13Support, Warranty, Copyright 14

Table of Contents

- 4 -

1. Product Overview

1.1 Product Features

1.2 Wiring Diagram

Two IP control modes: IP VISCA & ONVIF

Two analog control modes: RS422 & RS232

Three Control Protocols: VISCA, ONVIF and PELCO

Both the Controller and PTZ camera must be connected to the same LAN. The IP addresses of both the PTZ Camera and Controller must operate within the same network segment.

For example:192.168.1.123 is within the same segment as 192.168.1.111 192.168.1.123 is not within the same segment as 192.168.0.125

- 5 -

1.3 Technical Specifications

Ethernet 1 x Ethernet Port

JoystickFour-dimensional joystick control (up, down, left, right) Rotatable for zooming Tele/Wide

Connection Lead

Display LCD

Prompt Tone Button Sound Prompts On/Off

Power Supply DC 12V1AÂ±10%

Power Consumption 0.6 W Max

Operating Temperature 32°F-122°F

Storage Temperature -4°F-158°F

Dimensions 320 x 180 x 100mm

2. Function Description

2.1 Buntton Description

- 6 -

[AUTO FOCUS] Sets the camera in auto focus mode with this button. It will light up when the camera is in manual focus mode.

[AE AUTO] (Auto Aperture) Set the camera in automatic aperture mode with this button. It will light up when camera is in manual aperture mode.

[CAMERA OSD] Call/Close the camera OSD [HOME] Returns the camera back to home position if camera OSD is off. When the camera OSD is on, the home button confirms the function of camera OSD.

[F1]~[F2] Custom function buttons. In VISCA and IP VISCA modes. [SETUP] Local settings button, modifies & views local settings. Navigate menus using Joystick.

[SEARCH] Search for all available devices with ONVIF protocol in the LAN (only in ONVIF Mode).

[INQUIRE] Check added devices. [WBC MODE] (Auto White Balance) Sets the camera in auto white balance mode. Button will light up when camera is in manual white balance mode.

[CAM1]~[CAM4] Quickly switch device button: Quickly switch to CAM NUM 1-4 devices (ONVIF, IP VISCA), or to address code 1-4 devices (VISCA, PELCO).

[PRESE] Short presses will enable you to set presets; long presses will enable you to delete presets. Use the number keys and the “ENTER” button, when setting or deleting presets.

[CALL] Use the number keys and “ENTER” button to move the camera to a preset.

[IP] Manually adds network devices (only in ONVIF and IP VISCA modes). Use the “ENTER” button to confirm each step of the setup.

[CAM] In IP VISCA and ONVIF modes, it will quickly switch to the CAM NUM bound device when adding a device via CAM. In VISCA and PELCO modes, it will switch to the address code when entering a certain address. Use the “”ENTER” button to confirm each step of the setup.

[1]~[9] Number keys of 0,1,2,3,4,5,6,7,8,9. 2,4,6,8 also serve as directional keys, which can control pan and tilt rotation, and camera OSD.

[ESC] Return

[ENTER] Confirm Button. Be sure to press this button to confirm any/all settings.

- 7 -

2.2 Rocker Switch and Knob

2.3 Joystick Control

[NEAR] [FAR] Manually adjust the focal length.

[OPEN] [CLOSE] Manually adjust the aperture, OPEN(Aperture Plus)/CLOSE(Aperture minus)

[R-] [R+] Manually adjust the Red Gain

[B-] [B+] Manually adjust the Blue Gain

[PTZ SPEED-] [PTZ SPEED+] Adjust PTZ Speed 1-8: “-” = Slow. “+” = Fast.

[T-ZOOM-W] Zoom Tele and Zoom Wide

- 8 -

2.4 Terminal Description of Back Panel Interfaces

Back Panel Details: RS422, RS232, DC-12V, Ethernet, Power Switch

Move the joystick up and down to switch between basic settings. Move the joystick left or right to alter settings. Confirm settings with “ENTER” button.

1. Delete Device2. Network Type: Dynamic and Static3. Button Sound Prompt: On and Off4. Language Setting: English and Chinese5. Mode: VISCA, IP VISCA, ONVIF, PELCO

Number Label Physical Interface Description

1 RS422Control Output (TA, TB, TA, TB)

Connect to RS422 bus of the camera:TA to camera RATB to camera RBRA to camera TARB to camera TB

2 Ground Control line ground (G) Control signal Line ground

3 ETHERNET Ethernet Port Network Connection

4 DC-12V Power Input DV 12V Power Input

5 POWER Power Switch Power ON / OFF

3. Local Settings (SETUP)

3.1 Basic Settings

6. Local IP7. Version Information8. Restore Factory Settings9. Function Button 1 (“F1”) Setup10. Function Button 2 (“F2”) Setup

- 9 -

3.2 VISCA & IP VISCA Mode Shared Setting

3.3 IP VISCA Mode Setting

3.4 VISCA Mode Setting

3.5 PELCO Mode Setting

1. F1: Custom function for F1 button (VISCA command)2. F2: Custom function for F2 button (VISCA command)

Input custom name > ENTER > Input VISCA command For example: If the command is 8101040702FF, then input 01040702 (0 can’t be omitted)

Delete the saved device:

Move the joystick up and down to view devices; Move the joystick rightward to view the device’s port information; Move the joystick leftward to view the IP, CAM NUM information; ENTER to delete the selected device.

Control Settings (set the baud rate for a certain address code):

Move the joystick up, down, left and right to switch addresses (1-7) > ENTER > Move the joystick left and right to switch baud rate > ENTER

EX: Select the address: 1 > ENTER > Select the baud rate: 9600 > ENTER

When the controller is switched to address 1, the control baud rate is 9600

Control Settings (set the baud rate for a certain address code):

Move the joystick up, down, left and right to switch addresses (1-255) > ENTER > Move the joystick left and right to choose protocols > ENTER > Move the joystick left and right to switch baud rate > ENTER

- 10 -

3.6 ONVIF Mode Setting

Delete Saved Device:

Move the joystick up and down to view devices. Move the joystick rightward to view the device’s port information. Move the joystick leftward to view the IP, CAM NUM information. Press “ENTER” to delete the selected device.

EX: Select the address: 1 > ENTER > Select the protocol: PELCO-D > ENTER > Select the baud rate: 9600 > ENTER

When the controller is switched to address 1, the control baud rate is 9600, protocol is PELCO-D

Search and Add In ONVIF mode, follow the steps below to add a LAN device to the PTZ controller:

4. Connection and Control

4.1 Connection and Control in ONVIF Mode

1. After the controller has obtained IP address, simply press the SEARCH button.2. All available devices with the ONVIF protocol in the LAN will be displayed on the controller

when search process is complete.3. Move the joystick up/down to select the device. Press the “ENTER” button to confirm.4. It’s required to enter the device’s username, password and CAM NUM information when

adding a device.5. Press the “ENTER” button to save.6. Alternatively, use the [IP] button to add a device manually.7. Press the “INQUIRE” button to view the added device. Move the joystick up/down to view the

saved device (move the joystick rightward to view the port). Press the “ENTER” button to select a camera to control, or use the CAM button to connect and control.

- 11 -

The Searching function is not available in IP VISCA mode, but you can manually add a device.

1. Manually add device via the [IP] button.2. Press the “INQUIRE” button to view the added device. Move the joystick up/down to view

the saved device (move the joystick rightward to view the port); Press the “ENTER” button to select a camera to control, or use the CAM button to connect and control.

The Searching function is not available in IP VISCA mode, but you can manually add a device.

1. Connect the controller and computer to the same LAN and enter the controller’s IP address into the browser.

2. Default username: admin | Password: empty3. Home page is as below:

Simply set the address code and baud rate to control. In PELCO Mode, correctly set the PELCO-D or PELCO-P protocol.

4.2 Connection and Control in IP VISCA Mode

4.3 Control in VISCA & PELCO Mode

5. Web Page Configuration

5.1 Home Page

- 12 -

To modify the device IP access way and port parameters in LAN Settings, refer to image below:

Click save to confirm.

Dynamic address (default access way): the Controller will automatically acquire IP address from the router.

Static address: Change the network to static address when necessary; simply input the network segment information to modify.

5.2 LAN Settings

4. The home page consists of three segments: Search Device List (green); Added Device List (blue) or Manually Add (yellow); Device Details (orange).

5. Click the “Search” button to find ONVIF devices in the LAN. Devices will be displayed in the green frame automatically.

6. Select the device in the “Search Device List”, and click “Add” to complete. Press “Ctrl” for multiple selections.

7. Select the device in the “Added Device List”, and click “Delete” to complete. Press “Ctrl” for multiple selections.

8. After successfully adding a device, click the IP address in the “Added Device List” to edit the account and port information of the device.

9. After addition, deletion, and modification, click the “Save” button to confirm.

Note: A ny modification to the configuration on home page needs to be saved by clicking the “Save” button; otherwise any modifications are invalid.

- 13 -

The upgrade function is available for maintenance and updates.

Choose the update file and click “start” to update the controller. It will auto reboot after updating.

Note: Do not operate the controller, shut the power off, or disconnect the device from the network during the upgrade process.

Restore the controller to factory default settings when an unexpected failure occurs due toimproper modifications. Please use factory restoration with caution.

Click Reboot for maintenance if the controller has been running for a long period of time.

5.3 Upgrade

5.4 Restore Factory

5.5 Reboot

- 14 -

Learn More at www.ikancorp.com

Support

Contact email: [email protected]

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.

• The components and maintenance service fee will be charged if the warranty period is expired.

Free service will not be provided in the Following Situations: (*Even if the product is still within the warranty period.)

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.

• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

©2020 Ikan International. All rights reserved.

Documents

Manual OTTICA