Manual C4 C5

8/9/2019 Manual C4 C5

1/78

Second Edition

INSTALLATION MANUAL

< Optional Software >

FRONTIER SERIES

DI PRINT/DATA WRITINGSERVICE SOFTWARE Ver.5.5

PP3-A1001E2

(FRONTIER 355/375 System Disk Ver.1.5 or later)

(FRONTIER 350/370/390 System Disk Ver.6.6 or later)

(FRONTIER 330/340 System Disk Ver.2.0 or later)

DI Print/Data Writing Service Software Ver.5.5

distributed by www.minilablaser.com

[email protected]

8/9/2019 Manual C4 C5

2/78

INTRODUCTION

• This installation manual explains the procedures for installing and setting up the DI Print and

Data Writing Service for Fujifilm Digital Minilab FRONTIER Series as well as precautions for its

use.

• This manual should be kept in a fixed place near the machine so that it can be referred to at any

time a point needs to be clarified.

Specifications are subject to change without notification.

Zip™ is a trademark of Iomega Corporation.

SmartMedia™ is a trademark of Toshiba Corporation.

CompactFlash™ is a trademark of SanDisk Corporation.

Microdrive™ is a trademark of IBM Corporation.

Memory Stick™ and Memory Stick Duo™ are trademarks of Sony Corporation.

SD Memory Card™ is a trademark of Toshiba Corporation, Matsushita Electric Industrial Co., Ltd and SanDisk Copo-ration.

miniSD Memory Card™ is a trademark of SD Card Association.

Microsoft®, Windows® and Windows® 2000 are registered trademarks of Microsoft Corporation.

All other brand names or trademarks are the property of their respective owners.

INTRODUCTION


[email protected]

8/9/2019 Manual C4 C5

3/78

3

1 Precautions for Installation .............................................................................................. 5

1.1 Version of System/Option Software Combination .............................................................. 5

2 Hardware/System Configuration .................................................................................... 6

2.1 Hardware Configuration...................................................................................................... 6

2.1.1 FRONTIER 355/375 System.................................................................................. 6

2.1.2 FRONTIER 330/340 System.................................................................................. 7

2.1.3 FRONTIER 350/370/390 System........................................................................... 8

2.1.4 Imaging Controller System (Example).................................................................... 9

2.2 System Preparations .......................................................................................................... 10

2.2.1 PC and Media Drive Preparations.......................................................................... 10

2.2.2 Hard Disk Partition ................................................................................................. 11

2.2.3 Virtual Memory Setting........................................................................................... 112.2.4 Computer Name Setting......................................................................................... 13

2.2.5 Network Protocol Setting........................................................................................ 15

2.2.6 Creating a User Account ........................................................................................ 17

2.2.7 Restarting............................................................................................................... 20

3 Installation ............................................................................................................................... 22

3.1 Standard Setup/Upgrade.................................................................................................... 23

3.2 Custom Setup/Upgrade ...................................................................................................... 25

3.2.1 Custom Setup/Upgrade for Use of DI Print/Data Writing Service [C4/C5] ............. 25

3.2.2 Custom Setup/Upgrade for Use of DI Print Service [C4] Only ............................... 27

3.3 MSDE/64MB SmartMedia Driver Installation...................................................................... 30

3.3.1 MSDE Installation................................................................................................... 30

3.3.2 64MB SmartMedia Driver Installation..................................................................... 31

3.4 Backup Order Function....................................................................................................... 32

3.4.1 Added Functions .................................................................................................... 32

3.4.2 Installation .............................................................................................................. 33

3.5 Installation to FRONTIER................................................................................................... 35

3.5.1 [C4/C5] Installation................................................................................................. 35

3.5.2 Installation Information Setup................................................................................. 36

3.5.3 Print Size Setup...................................................................................................... 38

4 Setting the Imaging Controller ........................................................................................ 39

4.1 Print Service Administration ............................................................................................... 39

4.1.1 Setting for Media Drives and Executable Files....................................................... 41

4.1.2 Output Device Setting ............................................................................................ 42

4.1.3 Master Balance Adjustment ................................................................................... 43

4.1.4 Monitor Adjustment ................................................................................................ 44

4.1.5 DSC Setup ............................................................................................................. 45

4.2 Data Writing Administration................................................................................................ 46

4.2.1 Data Writing Statistic Log....................................................................................... 48

4.2.2 Media Drive Setting................................................................................................ 50

CONTENTSdistributed by www.minilablaser.com

[email protected]

8/9/2019 Manual C4 C5

4/78

4

4.2.3 Optional Software Setting....................................................................................... 51

4.2.4 Service Type Setting .............................................................................................. 52

4.2.5 Index Print Size Selection ...................................................................................... 544.3 Print-to-Print Service Administration................................................................................... 55

4.3.1 Registering of Print-to-Print Service ....................................................................... 55

4.3.2 Print-to-Print Service Settings ................................................................................ 56

4.4 Registering of Other Applications....................................................................................... 58

4.5 Digital Photo Center Administration.................................................................................... 59

4.5.1 Registering of Digital Photo Center Service........................................................... 59

4.5.2 Digital Photo Center Settings ................................................................................. 60

4.6 Multiple Service Setting ...................................................................................................... 62

5 Operation Test ....................................................................................................................... 645.1 Test DSC Printing............................................................................................................... 64

5.2 Test CD Writing .................................................................................................................. 66

5.3 Test Print-to-Print Operation............................................................................................... 69

6 Product Information............................................................................................................. 71

6.1 DI Print Product Information ............................................................................................... 71

6.1.1 Save to FD ............................................................................................................. 71

6.1.2 Log Contents.......................................................................................................... 72

6.2 Data Writing Product Information ....................................................................................... 73

6.2.1 Save to FD ............................................................................................................. 73

6.2.2 Log Contents.......................................................................................................... 74

7 Index........................................................................................................................................... 75


[email protected]

8/9/2019 Manual C4 C5

5/78

5

1 Precautions for Installation

1. FRONTIER 330 System Software and Optional Software

K :Available ✕ :N/A

2. FRONTIER 340 System Software and Optional Software


3.FRONTIER 350/370/390 System Software and Optional Software


Note1: Not available for FRONTIER 390

Note2: Operated only on Windows NT

Note3: Operated only with C4/C5 Ver.4.5 or later

A1 A2 B1 B3 B3/B4 B9 C2 C4/C5 C8 C10 C11

Ver.1.0 Ver.3.0 Ver.4.0 Ver.4.1 Ver.1.0 Ver.1.5 Ver.1.7 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0

Ver.1.0

K K✕

✕✕ ✕

✕

K K✕ ✕

✕✕ ✕

Ver.1.5 KK K

Ver.2.0 K ✕ K K K K K K

A1 A2 B1 B3/B4 B9 C2 C4/C5 C8 C10 C11

Ver.1.0 Ver.4.0 Ver.4.5 Ver.2.0 Ver.1.5 Ver.1.7 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0

Ver.1.0K

K ✕ ✕ ✕K K K

✕ ✕K K

✕

Ver.2.0 ✕ K K ✕ K K K

A1 A2 B1 B3 B5 B6 B7 B8 B9 B11

Ver.4.0 Ver.3.0 Ver.4.0 Ver.5.0 Ver.2.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.0 Ver.1.5 Ver.1.0

Ver.6.0

K K K K K K K K

(Note1)

✕ K ✕ ✕Ver.6.6

Ver.7.0 K ✕ K K

A1 C2 C4/C5 C8 C10 C11

Ver.1.6 Ver.1.7 Ver.4.1 Ver.4.5 Ver.4.6 Ver.5.0 Ver.5.5 Ver.1.1 Ver.1.0 Ver.1.0

Ver.6.0K

(Note2)

K

(Note3) K K K

✕ ✕

K K

✕

Ver.6.6K K K

Ver.7.0

1.1 Version of System/Option Software Combination

A1: FRONTIER System

B1: Variety Print

B5: Single Scan Digitizing Function

B8: Hyper Reorder

B9: Tone Selection

B11: Hyper Retouch

B12: FRONTIER Automatization Support Software

C2: DI I/O Service

C4/C5: DI Print/Data Writing Service

C8: LAN Spool

C10: Variety Print Digital

C11: Hyper Retouch Digital


[email protected]

8/9/2019 Manual C4 C5

6/78

6

2 Hardware/System Configuration

2.1.1 FRONTIER 355/375 System

2.1 Hardware Configuration

SP3000

LP1500SC/LP2000SC

HUB

Imaging ControllerPC Card

Reader

Zip Drive

I/O Box

MO Drive

CD-R

Drive

Flatbed Scanner

USB or SCSI connection

for use with Windows 2000

Imaging Controller(Example)

Monitor

Keyboard

Mouse

( )FD162B


[email protected]

8/9/2019 Manual C4 C5

7/78

7

2.1.2 FRONTIER 330/340 System

SLP-800SC/SLP-1000SE

HUB


Reader

Zip Drive

I/O Box

MO Drive

CD-R

Drive

Flatbed Scanner




Monitor

Keyboard

Mouse

( )FD162BC


[email protected]

8/9/2019 Manual C4 C5

8/78

8

2.1.3 FRONTIER 350/370/390 System

SP1500/SP2000/SP2500

LP1500SC/LP2000SC/LP2500P

HUB


Reader

Zip Drive

I/O Box

MO Drive

CD-R

Drive

Flatbed Scanner




Monitor

Keyboard

Mouse

( )FD162A


[email protected]

8/9/2019 Manual C4 C5

9/78

9

2.1.4 Imaging Controller System (Example)

Memory Stick TM , SD Memory Card TM and Microdrive TM can also be used as media when using Windows ® 2000

system.

Imaging Controller

PC CardReader

MO Drive

Monitor

Mouse

Keyboard

Flatbed Scanner

CD-R Writer

I/O Box

Zip Drive

CD-R Writer

FD163


[email protected]

8/9/2019 Manual C4 C5

10/78

10

2.2.1 PC and Media Drive Preparations

Prepare the PC, media drives, HUB, and the

cables.

1 PC that meets the following requirements:

CPU : Pentium II 400MHz

Hard disk : At least 9GB x 2 drives

Memory : At least 256MB

2 OSWindows NT4.0 Workstation SP6 or Windows

2000 Professional SP2

SCSI board must be installed beforehand.

3 Media drives and cablesZip, Jaz, MO, CD-R, PC card, SSFDC, CF,

Flatbed scanner, etc.

(SD Memory Card, Memory Stick and Microdrive

are supported only with Windows 2000)

In Windows 2000, the USB connection is also

available for the drive media except CD-R.

However, the processing speed in USB connec-

tion is not assured, and correct assignment of

drive name may not be done.

Required CD-R drive types:

• YAMAHA CRW 400tx

• YAMAHA CRW 4260tx

• YAMAHA CRW 4416sx• YAMAHA CRW 6416sx

• YAMAHA CRW 8424sx

• YAMAHA CRW 8824sx

• YAMAHA CRW 2100s-Vk

• PLEXTOR CD-R/W PX-W8220Te

• PLEXTOR CD-R/W PX-W124TSe

• PLEXTOR CD-R/W PX-W1210TS

• PLEXTOR CD-R/RW PX-W4012TS

(For the above CD-R drives, SCSI connection

is used with both Windows NT4.0 and Win-

dows 2000)

Make sure to use the SCSI connection for the

CD-R drive.

Required SCSI board:

• Adaptec 2940

• Adaptec 2930LP

• Adaptec 29160

Required CD-R:

• Fujifilm CD-R

Required scanner type:

• MICROTEK ScanMaker 4

• EPSON Expression 1600• EPSON Expression 1680

IMPORTANT:

Never use the CD-RW media instead of CD-R.

4 HUB and two network cables to connect Frontierto HUB and HUB to Imaging Controller.

5 CRT Monitor

• Color Temperature: 6500° K

• Resolution: 800 x 600 pixels or higher

• Display Color: 32bit

6 “Aspi” manager must be installed. If not, an errormay occur when starting “Data Writing” or “Print

to Print” software. At the installation of the

Windows NT, “Wnaspi32.DLL” is installed in the

“System32” folder in the “Winnt” folder in the C

drive, but it is not activated. To activate it, install

and set up “Wnaspi32.DLL” using any of the

following ways.

(1) Install “EZ-SCSI(CD-ROM)” provided with

“Adaptec 2940” SCSI board.

(2) Install the writing software “EZ-CD creator”

provided with the dedicated CD-R drives.

(See “Recommended CD-R drive types”

shown above.)

2.2 System Preparations


[email protected]

8/9/2019 Manual C4 C5

11/78

11

2.2.2 Hard Disk Partition

During the installation of Windows NT/Windows2000, partition your hard disk into two regions: one

for the system and the other for order registration

and spooling (Ex: 4GB for the system and 5GB for

order registration). For details see the Windows NT/

Windows 2000 setup manual.

2.2.3 Virtual Memory Setting

[In case of Windows NT]

1 On the Desktop, choose [Start] - [Settings] -[Control Panel].

2 Click the [System] icon in the “Control Panel”window.

• The “System Properties” screen appears.

3 Click [Change] under [Virtual Memory] on[Performance] tab.

• The “Virtual Memory” screen appears.

Select [Performance] tab.

Click.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

12/78

12

4 In the Drive list, click the drive you want tochange.

5 Under “Paging File Size for Selected Drive”, type“500” in the Initial Size (MB) and Maximum Size

(MB) boxes.

If the “Paging File Size” is less than 500MB,

make it more than 500MB.

If it exceeds 500MB, make sure to allocate it

more than the physical memory size.

6 Click [Set].

7 Click [OK].

• Operation returns to the “System Properties”

screen.

8 On the “System Properties” screen, click [OK].

• Operation returns to the “Control Panel” window.

[In case of Windows 2000]


2 Click the [System] icon in the “Control Panel”window.


3 Click [Performance Options] on [Advanced] tab.

• The “Performance Options” screen appears.

4 Click [Change].

• The “Virtual Memory” screen appears.

5 In the Drive list, click the drive you want tochange.

6 Under “Paging File Size for Selected Drive”,make sure that the Initial Size (MB) and

Maximum Size (MB) are more than 500MB.

If the “Paging File Size” is less than 500MB,

make it more than 500MB.

7 Click [Set].

8 Click [OK].

• Operation returns to the “Performance Options”,

so click [OK] to return to the “System Properties”

screen.

9 On the “System Properties” screen, click [OK].

• Operation returns to the “Control Panel” window.

Click.

Select the drive.

Click.

Click.

Check if the initial size (MB)and maximum size (MB) aremore than 500MB.


[email protected]

8/9/2019 Manual C4 C5

13/78

13

2.2.4 Computer Name Setting



2 Click [Network] in the “Control Panel” window.

• The “Network” screen is displayed.

3 Click [Identification] tab.

4 Move the cursor to the Computer Name and click[Change].

• The “Identification Changes” screen appears.

5 In the [Computer Name] box, type “FRONTEND”and click [OK].

• The confirmation message appears.

6 Click [OK].

• Operation returns to the “Network” screen.

Select [Identification] tab.

Click.

Type “FRONTEND”.

Click.


[email protected]

8/9/2019 Manual C4 C5

14/78

14

[In case of WIndows 2000]

1On the Desktop, choose [Start] - [Settings] -[Control Panel].

2 Click [System] in the “Control Panel” window.The “System Properties” screen is displayed.

3 Click [Network Identification] tab.

4 Click [Properties].

• The “Identification Changes” screen appears.

5 In the [Computer Name] box, type “FRONTEND”and click [OK].

• The confirmation message appears.

6 Click [OK].

• Operation returns to the “System Properties”screen.

Select [Network Identification] tab.

Click.

Type “FRONTEND”.

Click.


[email protected]

8/9/2019 Manual C4 C5

15/78

15

2.2.5 Network Protocol Setting


IMPORTANT: Make sure to use NetBEUI protocol.

1 On the “Network” screen, click [Protocols] tab.

2 Click “NetBEUI Protocol” in the NetworkProtocols and click [Close].

• The “Network Settings Change” message

appears.

3 Click [No].

4 If “NetBEUI Protocol” is not found in the “NetworkProtocols:”, register it.

(1) Click [Add].

(2) Select “NetBEUI Protocol” and then click

[OK].

(3) Complete the registration by following the

messages given.


IMPORTANT: Make sure to use NetBEUI protocol.

1 On the “Control Panel” screen, double-click[Network and Dial-up Connections].

Select [Protocols] tab.

Click.

Click.Select [NetBEUI Protocol].

Double-click.


[email protected]

8/9/2019 Manual C4 C5

16/78

16

2 Click [Local Area Connection] icon and then click[Network Identification] tab.

3 Double-click “Local Area Connection” icon.

• The “Local Area Connection Status” screen

appears.

4 Click [Properties].

5 Confirm if “NetBEUI Protocol” in the “Componentschecked are used by this connection:” is checked

[ √ ], and if not, check [ √ ] it.

6 If “NetBEUI Protocol” is not found in the“Components checked are used by this

connection:”, register it.

(1) Click [Install].

(2) Click [Protocol], and then click the [Add]

button.

(3) Select [NetBEUI Protocol] and then click

[OK].

Click.

Check if [NetBEUI Protocol] is checked [ √ ].

If [NetBEUI Protocol] is not found, click [Install].

Select [Protocol].

Click.

Select [NetBEUI Protocol].

Click.


[email protected]

8/9/2019 Manual C4 C5

17/78

17

2.2.6 Creating a User Account


1 On the Desktop, choose [Start] - [Programs] -[Administrative Tools] - [User Manager].

• The “User Manager” screen appears.

2 In the User menu, click “New User”.

• The “New User” screen appears.

3 Type “FRONTIER” in both the [User name] and[Full Name] columns, and enter a password in

both the [Password] and [Confirm Password]

columns.

• Check “Password Never Expires” box.

4 Click [Groups].

• The “Group Memberships” screen appears.

5 Choose “Administrators” and click [Add].

6 On the “Group Memberships” screen, click [OK].

7 On the “New User” screen, click [OK].

Type “FRONTIER”.

Click.


[email protected]

8/9/2019 Manual C4 C5

18/78

18


1On the “Control Panel” screen, double-click[Users and Passwords].

2 Click [Advanced] tab.

3 Click [Advanced].

4 Select [Tree]-[Users].

5 Select [New User···] from [Action] on the menubar.

6 Type “FRONTIER” in [User name], [Full name],[Password] and [Confirm password:] columns.

Remove the checkmark from “User must change

password at next log-on”, and check [ √ ] “Pass-

word never expires”.

7 Click [Create] and then click [Close].

Double-click.

Click [Advanced] tab.

Click.

Select [Tree]-[Users].

Type [FRONTIER].

Click [Create] then [Close].


[email protected]

8/9/2019 Manual C4 C5

19/78

19

8 Select [FRONTIER] from the right-hand list (1),and then select [Properties] from [Action] on the

menu bar (2).

9 Click [Member Of] tab, and then click [Add···]

10 Select [Administrators] on the “Select Groups”screen, and then click [Add] to add it to the list.

And then click [OK].

11 Click if “Administrators” exists in the list on[Member Of] tab of the [FRONTIER Properties]

screen.

12 Click [Apply] and then click [OK].

Select [FRONTIER] (1).

Select [Properties] (2).

Select [Member Of] tab.

Click.

Select [Administrators].

Click.

Click if “Administrators” exists.

Click [Apply] then [OK].


[email protected]

8/9/2019 Manual C4 C5

20/78

20

2.2.7 Restarting

1On the Desktop, choose [Start] - [Shut Down].

2 In case of Windows NT, click “Restart thecomputer?” and click [Yes].

In case of Windows 2000, select “Restart” and

click [OK].


• “(Build 1381: Service Pack 6)” is displayed in theupper right-hand corner of the Windows NT’s

BLUE starting screen.

• The settings take effect after restarting the com-

puter.

[Windows NT]

[Windows 2000]

Microsoft ® Windows NTTM Version 4.0 (Build 1381: Service Pack 6).2 System Processors [256 MB Memory] MultiProcessor Kernel

[Windows 2000]


[email protected]

8/9/2019 Manual C4 C5

21/78

21


• Check if the Service Pack is properly installedusing the following procedures.

1 On the “Control Panel” window, click [System]icon.


2 Check that the Service Pack 2 is displayed in the“System” on the “General” tab.

Click.


[email protected]

8/9/2019 Manual C4 C5

22/78

22

3 Installation

DI Print Service/Data Writing Software Ver.5.5 can only be operated in the following combination of the system

or other optional software.

FRONTIER 350/370 A1: System Software Ver.7.0 or later

FRONTIER 390 A1: System Software Ver.7.0 or later



IMPORTANT: Printing (including negative printing) cannot be performed during the installation.

IMPORTANT: Before starting the installation, perform the post-operational check, and shut down the FRON-

TIER. Do not shut it down by using the emergency stop button.

IMPORTANT: Before updating the “DI Print/Data Writing Service Software [C4/C5]” from Ver.4.5, Ver.4.6 and

Ver.5.0 to Ver.5.5, make sure that there are no orders in the DI Print [C4] and Data Writing [C5]

services, then close the [C4/C5]. When orders remain in the [C4/C5], complete the printing and

writing first, then start updating.

If you start updating while the orders remain in [C4/C5], they will be deleted.

(FRONTIER 330 Ver.2.0 or earlier/350/370/390) (FRONTIER 330/340 Ver.3.0 or later)

(FRONTIER 355/375)


[email protected]

8/9/2019 Manual C4 C5

23/78

23

1 Click the [Exit] button while pressing the [Shift]key to close the DI Print/Data Writing Service

[C4/C5].

2 Insert the DI Print and Data Writing ServiceSoftware CD into the CD-ROM drive.

3 Select [Run] from [Start] menu on the Desktop.

4 On the “Run” screen, enter “h:\setup.exe”, thenclick [OK].

The drive name (ex:h:\) varies according to the

CD-ROM drive into which you inserted the

installer CD.

5 On the “Setup Type Selection” screen, select[Standard Setup], then click the [Next] button.

3.1 Standard Setup/Upgrade

For the upgrade, use the same procedures as for the Standard Setup.

Before starting the installation of the DI Print/Data Writing Service Software [C4/C5], perform the Post-operational

check in FRONTIER and shut it down.

To install the DI Print/Data Writing Service Software [C4/C5] Ver.5.5, the Ver.5.0 software must be installed in the Imag-

ing Controller.

Click [Exit] while pressing [Shift] key.

FD201

Select [Standard Setup].


[email protected]

8/9/2019 Manual C4 C5

24/78

24

6 On the “Start Copying Files” screen, click the[Next] button.

• Installing starts.

7 Upon completion of installation, remove the CD

from the CD drive, and then restart the ImagingController.

Click.

FD202


[email protected]

8/9/2019 Manual C4 C5

25/78

25

3.2.1 Custom Setup/Upgrade for Use of

DI Print/Data Writing Service [C4/C5]

For the upgrade, use the same procedures as for the

custom setup.

Before starting the installation of the DI Print/Data

Writing Service Software [C4/C5], perform the Post-

operational check in FRONTIER and shut it down.

To install the DI Print/Data Writing Service Software

[C4/C5] Ver.5.5, the Ver.5.0 software must be installedin the Imaging Controller.


[C4/C5].






installer CD.

5 On the “Setup Type Selection” screen, select[Custom Setup], then click the [Next] button.

3.2 Custom Setup/Upgrade


FD201Select [Custom Setup].


[email protected]

8/9/2019 Manual C4 C5

26/78

26

6 On the “Select Application” screen, click the [DIPrint/Data Writing Service Software Ver.5.5]

button.

NOTE:

If “MSDE” and “64MB SmartMedia Driver” are

not installed in your system, install them.

( See “3.3 MSDE/64MB SmartMedia Driver

Installation” on page 30. )

7 On the “Setup Type Selection” screen, select [DIPrint/Writing Service]. Then, click the [Next]

button.

8On the “Working Drive Setting” screen, click the

[Next] button.

If you added a hard disk drive for temporary

directories, enter its drive name.

9 On the “Enter Text” screen, check if the“FRONTEND” is selected, and then click the

[Next] button.

10 On the “Spool Drive Setting” screen, select anydrive name (ex.“D”) as spool drive, and then click

the [Next] button.

The spool drives can be divided into two regions:

One for “Inspool” and another for “Outspool”.

Registered or digitized images are stored in the

“Outspool”. If you have added a hard disk drive

with a large storage space to the system,

change the drive name to the newly added drive

for storing large-size images.

Click.

Select a Setup type.

Click.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

27/78

27



12 Upon completion of installation, remove the CD

from the CD drive, and then restart the ImagingController.

3.2.2 Custom Setup/Upgrade for Use of

DI Print Service [C4] Only


custom setup.


[C4/C5].



Click.

FD202


FD201


[email protected]

8/9/2019 Manual C4 C5

28/78

28




installer CD.


6 On the “Select Application” screen, click the [DIPrint/Data Writing Service Software Ver.5.5]

button.

NOTE:

If “MSDE” and “64MB SmartMedia Driver” are

not installed in your system, install them.

( See “3.3 MSDE/64MB SmartMedia Driver

Installation” on page 30. )

7 On the “Setup Type Selection” screen, select [DIPrint Service Only]. Then, click the [Next] button.

8 On the “Enter Text” screen, click the [Next]button.


Select [Custom Setup].

Click.

Select a [DI Print Service Only].

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

29/78

29


10 Upon completion of installation, remove the CDfrom the CD drive, and then restart the Imaging

Controller.

FD202


[email protected]

8/9/2019 Manual C4 C5

30/78

30

3.3.1 MSDE Installation


2 On the “Select Application” screen, click the[MSDE] button.

• MSDE is installed.

3 In the “Restart” dialog box, click the [Yes] button.

3.3 MSDE/64MB SmartMedia Driver Installation

If your Imaging Controller already has the MSDE/64MB SmartMedia Driver Installed,

skip this section.


Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

31/78

31

3.3.2 64MB SmartMedia Driver Installation

1On the “Setup Type Selection” screen, select[Custom Setup], then click the [Next] button.

2 On the “Select Application” screen, click the[64MB SmartMedia Driver] button.

3 In the “Confirmation” dialog box, click the [Yes]button.

4 On the “Welcome” screen, click the [Next] button.

• The driver is installed right away.

5 On the “Setup Complete” screen, click the[Finish] button.


Click.

Click.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

32/78

32

3.4.1 Added Functions

By installing the Backup Order Function, the

following functions can be used.

[Printing(C4)]

• Re-registration function of printing order

• Test printing on the View and Order screen

[Writing(C5)]

• New services (devices) are added. The following

devices are added to the Digital Service Selec-

tion list.

• Picture RotationThe radio buttons for selecting the upper side

are added to the frames on the Image List

screen. To display these radio buttons, add the

checkmark [ √ ] to [Yes] box on [Picture Rotate]

on the Writing Service - Administration screen.

NOTE:

If the Backup Order Function is installed, process-

ing may be slower because the back-up processing

from the registered devices is done each time it is

executed.

NOTE:

This function cannot be uninstalled.

NOTE:

To disable this function, edit (comment-out) the

device for backup order function that is defined in

the “C:\FE\FEIN\InUkBackup.ini” file.

Service Name Functions

FDi CD1Three types of FDi CD are added.

Additional data such viewer can

be written.

FDi CD2

FDi CD3

FDi CD with FCD FUJICOLOR CD with FDi CD

(higher- or lower pixels)

Pro CD In this service the order uses the

print size selected in the Print

Size setup in film scanning, while

the original image size is adopted

in the DCS Printing.

3.4 Backup Order Function

Backup Order Function is the function where you can temporarily store the orders from the external

application (Kiosk, etc.), and later can correct them on the View and Order screen.


[email protected]

8/9/2019 Manual C4 C5

33/78

33

3.4.2 Installation

Install the Backup Order Function. Installation isdone by running the two batch files.


[C4/C5].

2 On the Desktop screen, select [Run] from [Start]menu.

3 On the “Run” screen, enter“H:\Merlin\MerlinPatch1.bat”, then click [OK].

The drive name (ex:H:\) varies depending on

your system.

• Installation (DOS) screen appears, and it disap-

pears when installing is completed.

4 On the “Run” screen, enter“H:\Merlin\MerlinPatch2.bat”, then click [OK].

The drive name (ex:H:\) varies depending on

your system.

5 On the confirmation (Registry Editor) screen,click [Yes].

6 On the confirmation (Registry Editor) screen,click [Yes].


Select [Start] - [Run].

Enter “H:\MerlinPatch1.bat”.

Click.

Enter “H:\MerlinPatch2.bat”.

Click.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

34/78

34

• After the restart, the [Backup Order] button and

[Main List/Backup List] tab appear on the Printing

screen.

[Backup Order] button

[Main List/Backup List] tab


[email protected]

8/9/2019 Manual C4 C5

35/78

35

3.5.1 [C4/C5] Installation

Install the [C4/C5] in the FRONTIER.


standard setup.

1 Insert the DI Print/Data Writing Service Software[C4/C5] installing or upgrading CD into the CD

drive, and then restart the FRONTIER after

performing the Post-operational Check.

2 On the “Enter Text” screen, click the [Next]button.



4 Upon completion of installation, restart theFRONTIER.

3.5 Installation to FRONTIER

[FRONTIER 330/340/355/375]

[FRONTIER 350/370/390]

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

36/78

36

3.5.2 Installation Information Setup

Set the external file I/O to ON to communicate withthe Imaging Controller.

■ FRONTIER 350/370/390

1 On the “Main Menu” screen, select [Setup andMaintenance] and click [OK].

2 In the “Log-in” dialog box, select [Laboratory

Manager], then enter the password “0000” andclick [OK].

3 Select [41 System Operation Setup and Check] -[41F Installation Information Setup] and click

[START].

4 Click [Option].

5 On the “Optional Device Setting” screen, set[External File I/O] to [YES], then click [OK].

Select “Laboratory Manager”.

Click.

Click.

Click.

Click [YES].

Click.


[email protected]

8/9/2019 Manual C4 C5

37/78

37

6 On the “[41F] Installation Information Setup”screen, click [OK].

7 In the confirmation dialog box, click the [OK]button.

■ FRONTIER 330/340/355/375

1 On the “Main Menu” screen, click the [Setup andMaintenance] button.

The above is an example of a FRONTIER 340

screen.

2Enter the password “7777”, and then click the[OK] button.

3 Select [01 System Operation Setup and Check] -[0140 Installation Information Setup].

4 On the “Installation Information Setup” screen,click the [Option] button.

5 On the “Optional Device Setting” screen, set[External File I/O] to [YES] and then click the

[OK] button.

6 In the confirmation dialog box, click the [OK]button.

Click.

Click.

Enter “7777”.

Click.

Click.

Click.

Set [External File I/O] to [YES].


[email protected]

8/9/2019 Manual C4 C5

38/78

38

3.5.3 Print Size Setup

On the FRONTIER, set the print sizes to be used inDIGITAL IMAGING PRINT SERVICE.

■ FRONTIRER 350/370/390

1 Perform Steps 1and 2 in “3.5.2 InstallationInformation Setup” (page 36) to open the “Setup

and Maintenance” screen.

2 Select [Print Condition Setup and Check] - [PrintSize Setup (424)] to open the “Print Size Setup”

screen.

3 Set the print size.

IMPORTANT:

When registering the print size, never use a

size designation with more than five charac-

ters.

If used, an error will occur when the connec-

tion is established with the Imaging Controller

at the pre-operational check.

4 Click the [OK] button.

5 Repeat Steps 3 and 4 for each print size.

■ FRONTIER 330/340/355/375

The following procedures use the FRONTIER 355 asexample.

1 Perform Steps 1 and 2 in “3.5.2 InstallationInformation Setup” (page 36) to open the “Setup

and Maintenance” screen.

2 Select [02 Print Condition Setup and Check] -[0220 Print Size Setup] to open the “Print Size

Setup” screen.

3 Set the print size.

IMPORTANT:

When registering the print size, never use a

size designation with more than five charac-

ters.

If used, an error will occur when the connec-

tion is established with the Imaging Controller

at the pre-operational check.


5 Repeat Steps 3 and 4 for each print size.

Select [02 Print Condition Setup and Check]

- [0220 Print Size Setup].


[email protected]

8/9/2019 Manual C4 C5

39/78

39

4 Setting the Imaging Controller

1 On the “Printing” screen, click the [Admin.]button.

2 In the “Password” dialog box, enter “DI”, and thenclick the [OK] button.

4.1 Print Service Administration

Perform the print service administration settings on the Print Service Administration screen. Here,

you can perform or change the settings such as the output device, media drive, etc.

Click. Enter “DI”.

Click.

No. Item Description

1 Index Print Select [Yes] to print the DSC index print.

2 Minimum Image Size Set the printable minimum image size, normally 20KB to avoid the registration of

too small images as such as thumbnails.

If trying to register the images with less than the set size, the following message

appears on the Order Registration screen.

6 5 9

8

1

19

102

3

4

7

11121314151617

18


[email protected]

8/9/2019 Manual C4 C5

40/78

40

3 Automatic Transaction

for all Frames

When [Auto.] button is turned ON, select a type of the automatic transactions on

the “Printing” screen.• to “Select All and Set”:

Automatic processing to the stage to “Select All and Set”. Click [Order Regist.] to

complete an order.

• to “Order Registration”:

Automatic processing to the stage to “Order Registration”. The registration is

completed simply by selecting media.

• to “View All Image”:

Automatic processing to the stage to “View and Order”. After the media selection,

you can monitor and adjust the images on the “View and Order” screen.

4 Back Print Select if the Back Printing is to be done or not. Add a checkmark [ √ ] to select it.

5 Default Print Q’ty Sets the default number of prints, index print and large index print sheets to be

output.

6 Key Step Set the CMYD key steps used on the “View and Order” screen (Recommended

values: CMY: 3, DcDmDy: 5).

7 Machine ID Identifies the multiple Imaging Controllers with this ID (a character of an alphabet

except “N” and “R”). This ID is added to the head of the order number.

8 Auto Correct - Disable If this is checked [ √ ], the auto correction is not applied to the image.

9 Help Displays the help screen.

10 Version Info. Displays the version information about this Software.

11 Statistic Log Stores the statistic information for each registered image data file into the FD, and

monitor them.

12 Monitor Adjust Displays the “Monitor Adjust” screen and matches the color balance of the monitor

to the print on the “View and Order” screen.

13 Master Balance Set the color master balance for printing for each print service. Normally set “0”.

14 Media Drive Set the media drives and relate them to the appropriate media icon.

15 Output Device Select the device name of the printer or other devices to be used.

16 Multiple Service Displays the “Multiple Services - Administration” screen.

17 DSC Setting Displays the “DSC Setup Setting” screen, where you can adjust the color, tone and

sharpness settings.

18 [OK] button Makes the settings effective. Control returns to the Printing screen.

19 [Cancel] button Cancels the settings. Control returns to the Printing screen.



[email protected]

8/9/2019 Manual C4 C5

41/78

41

4.1.1 Setting for Media Drives and Executable Files

On the Print Service Administration screen, click [Media Drive] to open the Media Drive Setting screen, onwhich you set the media drives and relate them to the appropriate media icon.

When using the external executable files such as PtoP and Digital Photo Center, set the icon and file path as

shown below.


1 Drives1 to18 The selected drive icons appear on the Printing screen.

2 Icon Display Displays the icons to be used.

3 Name Shows the drive name or software name.

4 Drive Select the drive letter and relate it to the icon.

5 File Path Specify the full path to the application.

Path and drive cannot be specified simultaneously.

6 [OK] button Makes the settings effective. Control returns to the Print Service - Administration

screen.

7 [Cancel] button Cancels the settings. Control returns to the Print Service - Administration screen.

Icon File Path

PtoP C:\FE\scanner\scanapp.exe

Digital Photo Center (LAN connections) DPC1 to DPC9 C:\FE\kiosk\kiosk.exe

Digital Photo Center (OFF line) DPC-Media C:\FE\kiosk\kiosk.exe X

Add “X” (drive name for DPC-Media). A space must beused to separate File Path from drive name for DPC-

Media.

2 5

1

7

6

3 4


[email protected]

8/9/2019 Manual C4 C5

42/78

42

4.1.2 Output Device Setting

On the Print Service Administration screen, click [Output Device] to open the Output Device Setting screen,on which you relate the output device to the icons.

IMPORTANT:

These settings can be done only if the pre-operational check is completed on the FRONTIER 330/350/370/

390.


1 Output Devices1 to 8 The icons of the output devices appear on the Printing screen in this order.

2 Icon Selection Select the desired output device icon by clicking it.

3 Icon Name Specify the device name under the icon using up to 8 characters.

To use the Hyper-Retouch Service [C11], install it beforehand.

4 Device This information is registered to the system at the time of “Pre-operational check” inFRONTIER.

2 5

1

6

3 4

7

Default print sizecannot be set in the“Multiple” service.

FRONTIER Device Name

330 SP-800sRGB or SP-800PD


350/370 SP-1500/2000sRGB or SP-1500/2000PD


355/375 SP-3000sRGB or SP-3000PD


[email protected]

8/9/2019 Manual C4 C5

43/78

43

5 [Print Size] button Displays the “Print Size Setting”

screen.These buttons set the default values

of DSC/Media, DPOF Print, Index

print and Large Index. Press [Print

Size] button to set the desired print

size for each print service. This value

will be displayed on the “Printing”

screen. Once the size is specified as

default, this value will be displayed.

In the “Multiple” service, the

default print size cannot be

selected.

6 [OK] button Makes the settings effective. Control returns to the Print Service screen.

7 [Cancel] button Cancels the settings. Control returns to the Printing screen.


4.1.3 Master Balance Adjustment

On the Print Service Administration screen, click

[Master Balance] to open the Master Balance

screen, on which you set the color balance forprinting for each print service.

The settings done on this screen are only applied to

the print, not to the CD-R writing.

1 Set the master balance with the value from -99%to +99% for each service Digital Still Camera

Print, CD-R Reprint or Media Print.

2 Click [OK] button to make the settings effective.Control returns to the Print Service -

Administration screen.

3 Click [Cancel] button to cancel the settings.Control returns to the Printing screen.


[email protected]

8/9/2019 Manual C4 C5

44/78

44

4.1.4 Monitor Adjustment

On the Print Service Administration screen, click[Monitor Adjust] to open the Monitor Adjust screen,

on which you match the color balance of the

monitor to the print.

1 Select [Auto Corr.] tab or [No Corr.] tab.

2 On the Monitor Adjust screen, click [SamplePrint] to register the sample print order.

3 After the disappearance of the sandglass icon,click [Cancel] to return to the Print Service -

Administration screen. And then click [Cancel] to

return to the Printing screen.

4 Print the order ZA9998 (No Correction) orZA9999 (Auto Correction) on FRONTIER.

• “CX MX YX” is printed on the back of the sample

print.

5 When the sample print is output, open theMonitor Adjust screen again. And then adjust the

CMY while checking the color on the print.

6 And then click [Apply] to apply the adjustedvalues to the monitor.

7 Repeat Step 5 several times, and then click [OK]to register the values. Control returns to the

Printing - Administration screen.

8 Click [OK] button to make the settings effective.Control returns to the Print Service -

Administration screen.

9 Click [Cancel] button to cancel the settings.Control returns to the Printing screen.

[Auto Correction]

[No Correction]


[email protected]

8/9/2019 Manual C4 C5

45/78

45

4.1.5 DSC Setup

On the “DSC Setup Setting” screen, you can set and change the initial parameters for color, tone andsharpness adjustment for DSC printing. On the “Print Service - Administration” screen, click [DSC Setting].


1 Color Intensity Set up the chroma saturation value from -2 to +4.

2 Gradation Adjustment Select the type of Pro DI Gamma from “Hard2” to “Soft3”.

3 Hyper Tone Select the mode of the Hyper Tone.

4 Sharpness Select “Noise Reduction” or “Standard (USM)” for sharpness type.

5 [Help] button Displays the Help screen.

6 [OK] button Makes the settings effective. Control returns to the “Print Service - Administration”screen.

7 [Cancel] button Cancels the settings. Control returns to the “Print Service - Administration” screen.

1

4

6

3

2

7

5


[email protected]

8/9/2019 Manual C4 C5

46/78

46

1 On the “Writing” screen, click the [Admin.]button.


4.2 Data Writing Administration

Click. Enter “DI”.

Click.


1 Adapter No. and SCSI ID Select an appropriate combination of SCSI HOST Adapter number and SCSI ID for

the CD-R drive.

2 CD-R Drive Name Select the drive name for the CD-R drive.

3 CD-ROM Drive Name Select the drive name for the CD-ROM drive.

1

18

17

3

11

2

5

67

8

9

10

4

19

12131415

16


[email protected]

8/9/2019 Manual C4 C5

47/78

47

4 Verify Type Selection • Verify after writing (new CD-R):

Check the box to verify the CD-R after writing in a new CD writing.

Normally remove the checkmark [ √ ].

• Verify after writing (additional data):

Check the box to verify the CD-R after writing in an additional writing.

Normally checkmark [ √ ].

5 Media Drive Displays the drive set for writing on the Media Drive Setting screen.

6 Media Drive Setting Displays the Media Drive Setting screen.

7 Optional Software

Setting

Displays the application software set on the Optional Software Setting screen.

[Setting] button:

Displays the Application Software Call Setup screen.

8 CD-R Index Setting Set the device for printing the CD-R index and large-index prints, and their printsize, and then set “Yes” or “No” to print them.

[Device]:

Select the device for printing the CD-R index or large-index prints.

For large index print, normally select “A4 (210x297mm)” or “8R (203x254mm.

254x203mm)”

9 Print Size Click [Select] to display the Print Size Selection screen.

10 Index/Large Index Sets the default value for “Yes” or “No” to Index/Large Index on Image List screen.


12 Version Info. Displays the version information.

13 Statistic Log Display the Statistic Log screen.

14 Service Type Setting Displays the Service Type Setting screen.

15 Multiple Service Displays the Multiple Service screen. (See “4.6 Multiple Service Setting” on page

62.)

16 Writing Speed Select [Fast] or [Normal] for data writing speed.

[Fast] : maximum capability of device

[Normal] : octuple speed

17 Data Delete Interval Set up the time (min) for the data to be deleted after completing processing.

Range : 0-999

18 [OK] button Stores the settings and exits this screen.

19 [Cancel] button Exits this screen without storing the settings.



[email protected]

8/9/2019 Manual C4 C5

48/78

48

4.2.1 Data Writing Statistic Log

On the Writing Service Administration screen, click [Statistic Log] to open the Log screen, on which youdisplay and store the statistic log. (For details of product information, see “6 Product Information”.)


1 Period Displays the period during which the statistic log is accumulated.

2 Writing Total Displays the total copies of writing during the period.

3 Service Displays the writing service type.

4 Copies Displays the number of copies.

5 Images Displays the number of images.

6 [Help] button Displays the Help screen.7 [Save] button Saves the statistic log to FD. As the log has the “CSV” format, it can be monitored

by using the spreadsheet software.

8 [Return] button Exits this screen.

1

7

3

62

4 5

8


[email protected]

8/9/2019 Manual C4 C5

49/78

49

In the above dialog box, click [Yes] to remove the Writing log. Note that the Writing log can be removed only in

this dialog box, not on the “Product Information” screen.

Note that the removed log is never restored.


1 Starting date Specify the starting date to log.

2 Saving days Specify the number of days to be saved.

3 Path to save Shows the drive/path where the log file will be output.

1

3

2


[email protected]

8/9/2019 Manual C4 C5

50/78

50

4.2.2 Media Drive Setting

Select the name, icon and output path and relate them for each media drive other than the CD-R media. Thefollowing three writing services are registered as default.

CD-R 4base JPG

FUJICOLOR CD(4base,JPG)

Free Export BMP

Set the media type on this screen, and then make Service Type Settings on the Service Type Setting screen.

(See “4.2.4 Service Type Setting” on page 52.)

On the Writing Service Administration screen, click [Media Drive Setting] to open the Media Drive Setting

screen.


1 Icon Select icons for displaying on the Main screen.

2 Drive Set the drive letter for the writing drive.

3 Output Path Enter the directory name with the full path for writing to HD or network drive.

4 [Brows...] button Displays the Browse screen for selecting the directory. The selected directory

appears in the Output Path box.




7

1

5

2 3

4

6


[email protected]

8/9/2019 Manual C4 C5

51/78

51

4.2.3 Optional Software Setting

On the Writing Service Administration screen, click [Setting] in the Optional Software Setting field to open theOptional Software Setting screen, on which you can set the FUJIFILM optional software (up to three different

packages).

For example, when using the Digital Photo Center, use the pull-down menu to select “Digital Reorder”, and

then specify “C:\FE\DR\DigitalReorder.exe” as Path for the Optional Software.


1 Icon Select the icon for the software.

2 Path for the Optional

Software

Enter the full path name to locate the selected software.

3 [Help] button Displays the Help screen.4 [Brows...] button Displays the file selection screen for selecting the file. The selected file appears in

the Path for the Optional Software Output Path. Select only the file with “exe”

extension.



1

6

3

4

5

2


[email protected]

8/9/2019 Manual C4 C5

52/78

52

4.2.4 Service Type Setting

Use the “Service Type Setting” screen for setting the type of several writing service combination of MediaType, File Format and Image Size.

On the Writing Service Administration screen, click [Service Type Setting] to open the Service Type Setting

screen.


1 Service Name Displays the service name with the media type, file format and image size.

The selected service name is displayed on the Output Device Selection screen

when performing Digital Image Export on the FRONTIER.

2 Media Type Displays the media type for the writing service.

Supported media type: CD-R

Free Export (same function as C2: BMP Export provides)

3 File Format Displays the selected image file format.

Supported file format: JPG (Exif-JPG), FPX, BMP, FUJICOLORCD

4 Image Size (Base) Displays the type of the image size.

Supported image size: 1base, 4base, 16base, Free Size


6 [Set] button Register the service name with the media type, file format and image size, and add

it to in the list.

7 [Delete] button Deletes the selected service name.

8 [Return] button Exits this screen.

5

8

21 3 4

76


[email protected]

8/9/2019 Manual C4 C5

53/78

53

Restrictions for Service Type Combination

(1) When selecting “FREE EXPORT” as Media Type, only “Print Size” can be specified as Image Size.(2) When selecting “FUJICOLOR CD” as File Format, only “4base” as Image Size and “CD-R” as “Media

Type” can be selected.

(3) When selecting “FD” as Media Type, only “1base” can be selected as Image Size.

The following table shows the relation between Media Type, File Format and Image Size.

Service Composition

Media Type File FormatImage Size

1Base 4Base 16Base Free Size

CD-R

FPX

Available Available Available AvailableJPG

BMP

FUJICOLOR CD N/A Available N/A N/A

FDi CD N/A Available N/A N/A

CD Pro N/A N/A N/A Available

ZIP/JAZ/MO/

HD1 to 6

FPX

JPG

BMP

Available Available Available N/A

FD JPG Only Film Scan N/A N/A N/A

Free ExportJPG

BMPN/A N/A N/A Available


[email protected]

8/9/2019 Manual C4 C5

54/78

54

4.2.5 Index Print Size Selection

On the Writing Service Administration screen, click [Select] in the CD-R Index Setting field to open the PrintSize Selection screen, on which you select the print size for the index print.

This service is available only for film scanning.


1 No. Displays the serial number.

2 Name Displays the print size name.

3 Width (mm) Displays the paper width (mm).

4 Feed (mm) Displays the paper feed (mm).

5 Width (pixel) Displays the paper width (pixel).

6 Feed (pixel) Displays the paper feed (pixel).

21 3 4 5 6


[email protected]

8/9/2019 Manual C4 C5

55/78

55

4.3.1 Registering of Print-to-Print Service

Set up the file path to the executable file for the

Print-to-Print Service on the “Print Service -

Administration” screen.



3 On the “Print Service - Administration” screen,click the [Media Drive] button.

4 Set the icon and file path as shown below.


6 On the “Print Service - Administration” screen,click the [OK] button.

4.3 Print-to-Print Service Administration

Perform the Print-to-Print service settings on the Administration screen.

Click.

Enter “DI”.

Click.

Click.

Icon File Path

PtoP C:\FE\Scanner\scanapp.exe

Select the icon file path.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

56/78

56

4.3.2 Print-to-Print Service Settings

Set up the administrative items for Print-to-PrintService.

1 On the “Printing” screen, select the output deviceand then click the [PtoP] button.

2 On the “Print-to-Print” screen, click the [Admin.]button.

Select the output device.

Click.

Click.

3 Perform the administration work as shown below.


1 Output Device Select the output device from the Output Device pull-down menu.2 Print Size Select the default print size from the Print Size pull-down menu.

15

2

8

9

7

6

34


[email protected]

8/9/2019 Manual C4 C5

57/78

57

5 and 6 can be set only after the fine scanning is completed.

3 TWAIN Source Select the TWAIN source from the TWAIN Source pull-down menu.

Enter any of the following TWAIN sources.Microtek Scanmaker 4: Microtek ScanWizard(32bit)

EPSON Expression 1600/1680: EPSON TWAIN Pro(32bit)

4 Scanner Type Select the scanner type from the Scanner Type pull-down menu.

5 Scanner Balance Adjust the master color balance for this service after the fine scanning.

(Value: -99 to +99)

6 Monitor Balance Adjust the monitor color balance for this service after the fine scanning.

(Value: -99 to+99)

7 Contrast Adjust the contrast for the highlight or shadow part of the image after the fine

scanning. (Value: -5 to +5)

8 [OK] button Allows all settings to take effect then returns to the main screen9 [Cancel] button Cancels all settings then returns to the main screen.



[email protected]

8/9/2019 Manual C4 C5

58/78

58

1 On the “Writing” screen, click the [Admin.]button.

2 On the “Writing Service - Administration” screen,click the [Setting] button in the [Optional

Software Setting] field.

3 On the “Optional Software Setting” screen, setup the icon and file path as shown below.


5On the “Writing Service - Administration” screen,click the [OK] button.

Icon File Path

Reorder C:\FE\DR\DigitalReorder.exe

4.4 Registering of Other Applications

Set up the file path to the executable file for other applications on “Writing Service - Administration”

screen. This section explains how to set up the Digital Reorder service application.

Click.

Click.

Set up the icon and file path.

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

59/78

59

4.5.1 Registering of Digital Photo Center

Service

Set up the file path to the executable file for the

Digital Photo Center Service on the “Print Service -

Administration” screen.



3 On the “Print Service - Administration” screen,click the [Media Drive] button.

4 Set the icon and file path as shown below.


4.5 Digital Photo Center Administration

Digital Photo Center is an in-store order terminal that is connected to the Imaging Controller.

When using it, perform the Digital Photo Center service settings on the Administration screen.

Click.

Enter “DI”.

Click.

Click.

Icon File Path

DPC1 to DPC9

(LAN)

C:\FE\kiosk\kiosk.exe

DPC-Media

(OFF-line)

C:\FE\kiosk\kiosk.exe X

Add “X”

(drive name for DPC-MEdia)

Set the icon and file path.

Click.


[email protected]

8/9/2019 Manual C4 C5

60/78

60

6 On the “Print Service - Administration” screen,click the [OK] button.

4.5.2 Digital Photo Center Settings

Set up the administrative items for Digital PhotoCenter Service.

1 On the “Printing” screen, click the [DPC1] to[DPC9] or [DPC-M] button.

2 On the “Digital Photo Center” screen, click the[Admin.] button.

Click.

Click [DPC1] to [DPC9] or [DPC-M].

Click.


[email protected]

8/9/2019 Manual C4 C5

61/78

61

3 Perform the administration work as shown below.

■ Spool Setting Screen

No Item Description

1 Print Setting Select the name of the device currently connected and the print size to be used.

The information will be registered in the FRONTIER data base.

Click the [Spool Setting] to display the following “Spool Setting” screen.

No Item Description

1 Spool Setting Specify the name of the folder for the storing spool. The name must be specified by

the full path name such as D:\DPCdata\. Normally enter the following values.

Root Path: D:\DPCdata

Frontier Print: pcpr

DPC Print: aldn

1

1


[email protected]

8/9/2019 Manual C4 C5

62/78

62

The Multiple Service is a service that provides multiple order registration at a time of film scanningor image entry from the Digital Media. To use this service, register a combination of output devices

beforehand. Use the following procedures to register it.

On the “Print Service - Administration” screen or “Writing Service - Administration” screen, click [Multiple

service] button.

• The “Multiple Service - Administration” screen appears.

No Item Description

1 Multiple Service List Lists up the names of the multiple services that were registered.

2 Multiple Service

Composition

Shows the selected service contents.

3 Multiple Service Name Enter the name of the service in this space.

4 Print Output Device Select an output device. This information is registered to the system at the time of

“Pre-operational check” in FRONTIER.

5 Image Writing Service Select a writing service to be registered.

6 Image Use Service Select it when using Digital Reorder or NET service.

7 Other (Not used)


9 [1 Line Up] button Moves the selected service upward in the Multiple Service List.

10 [1 Line Down] button Moves the selected service downward in the Multiple Service List.

11 [Entry] button Adds the selected service to Multiple Service List.

12 [Delete] button Removes the selected service from Multiple Service List.

13 [Return] button Returns to the Print Service - Administration screen.

4.6 Multiple Service Setting

1

8

13

2

45

6

1211

3

9

10


[email protected]

8/9/2019 Manual C4 C5

63/78

63

■ Setting Procedures

1Select the items to be serviced in the “Service Composition”.

2 Enter the name of the multiple service in the “Multiple Service Name”.

3 Click the [Entry] button.

• The created service is added to the “Multiple Service List”.

4 Click the [Return] button.

• Control returns to the “Print Service - Administration” screen or “Writing Service - Administration” screen.


[email protected]

8/9/2019 Manual C4 C5

64/78

64

5 Operation Test

1 Set the media including the image(s) in the drive.

2 Select the printing device in the [OUTPUT] field,and then any of the media in the [INPUT] field.

3 Find the folder, and then select the image(s).

4 Click the [Set] button to list up the images in the“Order Specification Column”.

5 Click the [Order Regist.] button.

6 The “Confirmation” dialog box appears.

5.1 Test DSC Printing

Perform the test DSC printing, CD writing, and Print-to-Print operation.

FD214

Select the printing device.

Select the media.

Select the image(s).

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

65/78

65

7 Remove the media from the drive.

8Click the [OK] button.

9 Print the registered images with FRONTIER.

FD124

Click.

(FRONTIER 350/370/390)

(FRONTIER 330/340)

(FRONTIER 355/375)


[email protected]

8/9/2019 Manual C4 C5

66/78

66

1 Set the media including the image(s) in the drive.

2 Select the writing device in the [OUTPUT] field,and then any of the media in the [INPUT] field.

3 On the “Service Select” screen, click the [OK]button.

4 Find the folder, and then select the image(s).

5 Click the [Set] button to list up the images in the“Order Specification Column”.

6 Click the [Order Regist.] button.

5.2 Test CD Writing

FD214

Select the writing device.

Select any of the media.

Click.

Select the image(s).

Click.

Click.


[email protected]

8/9/2019 Manual C4 C5

67/78

67

7 The “Confirmation” dialog box appears.

8 Remove the media from the drive.


10 Click the [Writing] icon to display the “Writing”screen.

11 Double-click the order in the [Order Registration]Status field.

12 On the Image List screen, check the image(s),and then click [OK] button.

13 Insert the CD-R into the drive.

FD124

Click.

Click the [Writing] icon.

Double-click.

C45019


[email protected]

8/9/2019 Manual C4 C5

68/78

68

14 Click [OK] button. In case of media writing, insertthe specified media instead of CD-R.

15 Writing is started.


17 Remove the CD-R from the drive.

Click.

Click.

C45020


[email protected]

8/9/2019 Manual C4 C5

69/78

69

1 Click [PtoP] in the [INPUT] field.

2 Set the photo on the scanning table glass.

3 Click the [Fine Scan] button.

4 Click the [Add image to Order] button.

5 Click the [Order Regist] button, then the [Return]button.

6 Remove the photo from the scanner and store itin a safe place.

5.3 Test Print-to-Print Operation

Click.

FD191

FD192


[email protected]

8/9/2019 Manual C4 C5

70/78

70

7 Print the registered images with FRONTIER.

(FRONTIER 350/370/390)

(FRONTIER 330/340)

(FRONTIER 355/375)


[email protected]

8/9/2019 Manual C4 C5

71/78

8/9/2019 Manual C4 C5

72/78

72

6.1.2 Log Contents

Monitor the statistic log information using some editor, or spread sheet software.

Example of Data Items:

*1 “Win” appears also for Mac processing because it is converted to Win format in the application software.

1 Order NO.

2 Reception date

3 Order file version

4 Order file creating date

5 Driver

6 Application name

7 Camera model (only EXIF)

8 Flash No/Yes

9 Format*1

10 Print Q'ty

11 File name

12 print size

1 2 3 4 5 6 7 8 9 10 11 12

A00650 2004/9/

420:53

V1.00 2004/9/4 F-DI Net Serner

V2.00

Win 10 DPC001.FPX POST

CARD

A00656 2004/9/

711:50

FUJIFILM

FinePix500

YES Win 1 DSCF0013.JPG DSC

A00661 2004/9/

711:57

FUJIFILM

FinePix700

NO Win 1 DSC00001.JPG DSC

A11664 2004/9/

712:02

NIKON E900 NO Win 1 DSC00001.JPG DSC

A00668 2004/9/ 712:07

FUJUFILMDS-30

NO Win 1 DSC00001.JPG DSC

A00669 2004/9/

712:07

RICOH DC-4 YES Win 1 RIM0009.JPG DSC

A00674 2004/9/

716:09

Win 1 SONYMVCFD7

.JPG

DSC

A00011 2004/9/

716:16

V1.00 2004/6/30 phex-win-v1.50 PICTURE.EXE Win 1 4.FPX A5

A00030 2004/9/

714:07

V1.00 2004/9/7 PD-WIN -V1.50 MAMEW9.EXE Win 3 2.FPX C

A00030 2004/9/

814:07

V1.00 2004/9/7 PD-WIN -V1.50 PHOTOS01.DLL Win 10 4.FPX POST

CARD


[email protected]

8/9/2019 Manual C4 C5

73/78

73

6.2.1 Save to FD

1 Click the [Statistic Log] on the “Writing Service -Administration” screen.

• The “Log” screen appears.

2Click the [Save to FD] button.

3 On the “Save Statistic Log” screen, select[Starting date] and [Saving days], then click the

[OK] button.

4 Insert a formatted 1.44MB FD into the FD drive.

Make sure to use a new formatted FD.

• Log file is copied FD.

• Upon completion the copy, the message appears.

5 Click the [Yes] button.

6.2 Data Writing Product Information

Click the [Statistic Log] button.


[email protected]

8/9/2019 Manual C4 C5

74/78

8/9/2019 Manual C4 C5

75/78

75

7 Index

Numerics64MB SmartMedia Driver Installation.....................31

BBackup Order Function.............................................32

———Added Functions ............................................32

———Installation.......................................................33

C[C4/C5] Installation ....................................................35

Computer Name Setting ...........................................13

Creating a User Account ..........................................17

Custom Setup/Upgrade ............................................25

Custom Setup/Upgrade for Use of

DI Print Service [C4] Only .................................27

Custom Setup/Upgrade for Use of

DI Print/Data Writing Service [C4/C5] .............25

DData Writing Administration .....................................46

Data Writing Product Information ............................73

Data Writing Statistic Log .........................................48

DI Print Product Information ....................................71

Digital Photo Center Administration........................59Digital Photo Center Settings ..................................60

DSC Setup ..................................................................45

FFRONTIER 330/340 System .....................................7

FRONTIER 350/370/390 System..............................8

FRONTIER 355/375 System .....................................6

HHard Disk Partition.....................................................11

Hardware Configuration..............................................6

Hardware/System Configuration ...............................6

IImaging Controller System (Example) .....................9

Index Print Size Selection ........................................54

Installation...................................................................22

Installation Information Setup ..................................36

Installation to FRONTIER.........................................35

LLog Contents ....................................................... 72, 74

MMaster Balance Adjustment .....................................43

Media Drive Setting ...................................................50Monitor Adjustment ...................................................44

MSDE Installation ......................................................30

MSDE/64MB SmartMedia Driver Installation ........30

Multiple Service Setting ............................................62

NNetwork Protocol Setting..........................................15

OOperation Test ...........................................................64

Optional Software Setting ........................................51

Output Device Setting ...............................................42

PPC and Media Drive Preparations ..........................10

Precautions for Installation.........................................5

Print Service Administration.....................................39

Print Size Setup .........................................................38

Print-to-Print Service Administration ......................55

Print-to-Print Service Settings .................................56

Product Information ...................................................71

RRegistering of Digital Photo Center Service ..........59

Registering of Other Applications ...........................58

Registering of Print-to-Print Service .......................55

Restarting....................................................................20

SSave to FD ........................................................... 71, 73

Service Type Setting .................................................52

Setting for Media Drives and Executable Files .....41

Setting the Imaging Controller .................................39

Standard Setup/Upgrade..........................................23

System Preparations.................................................10

TTest CD Writing..........................................................66

Test DSC Printing ......................................................64

Test Print-to-Print Operation....................................69

VVersion of System/Option Software Combination ....5

Virtual Memory Setting .............................................11


[email protected]

8/9/2019 Manual C4 C5

76/78


[email protected]

8/9/2019 Manual C4 C5

77/78

Fujifilm’s Technical Division Photo Products Marketing would be most grateful if you would make copies of this

form, then complete and send them to us by FAX.

Your opinions will contribute greatly to an accurate assessment of the overall quality of each manual.

All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please

provide us with your written comments in the lined spaces following each block of questions.

Manual Title and Reference Number

Title :

Reference Number :

Your Name and Company

Name :

Company :

Your E-mail Address and FAX Number

E-mail Address :

FAX Number :

Question 1 • How would you rate this manual overall?

(1) Very easy to use and understand (2) Fairly easy to use and understand

(3) Slightly difficult to use

and understand

(4) Very difficult to use and understand

• Please provide us with your reasons and comments.

Question 2 • Have you found any technical errors, errors in spelling, or missing words in this manual?

Yes No

• If you have ticked (Yes), please let us know what these errors and missing words are.

Question 3 • How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/

diagrams, etc.?

(1) Clear and easy to follow (2) Should be simplified

(3) Difficult to follow

(1)’ [Illustrations, etc.] Of adequate size

(2)’ [Illustrations, etc.] Too small

(3)’ [Illustrations, etc.] Difficult to follow

• If you have ticked (2), (3) or (3)’, please give us your reasons.

Additional

Comments/

Requests

concerning

This Manual

FAX : 81-3-5484-0454

Please return this questionnaire to : FAX No. : Tokyo 81-3-5484-0454

FRONTIER Series

DI Print/Data Writing Service Software Ver.5.5

INSTALLLATION MANUAL

PP3-A1001E2

Questionnaire concerning This Manual


[email protected]

8/9/2019 Manual C4 C5

78/78


Documents

Manual C4 C5