Mantis rototiller

7/22/2019 Mantis rototiller

1/32

Tiller/CultivatorOWNERS MANUAL


2/32


3/32 3

SAFETY RULES & WARNINGSYou will notice throughout this Owners Manual Safety Rules and Important Notes. Make sure youunderstand and obey these warnings for your own protection.

I. Special Safety Information

WARNING DANGERATTENTION: THIS SYMBOL POINTS OUT

OUR IMPORTANT SAFETY INSTRUCTIONS.

WHEN YOU SEE THIS SYMBOL,

HEED ITS WARNING!! STAY ALERT!!

WARNING DANGERTO REDUCE THE POTENTIAL FOR ACCIDENTS, COMPLY

WITH THE SAFETY INSTRUCTIONS IN THIS MANUAL.

FAILURE TO COMPLY MAY RESULT IN SERIOUS PERSONAL

INJURY, AND/OR EQUIPMENT AND PROPERTY DAMAGE.

WARNING DANGERIMPROPER USE OR CARE OF THIS TILLER

OR FAILURE TO WEAR PROPER PROTECTION

CAN RESULT IN SERIOUS INJURY.

READ AND UNDERSTAND THE RULES FOR SAFE OPERATION

AND ALL INSTRUCTIONS IN THIS MANUAL.

WEAR HEARING AND EYE PROTECTION.

II. Safety & Warnings

!

WARNING: The Engine Exhaust from this product contains chemicals knownto the State of California to cause cancer, birth defects or other reproductive harm.

!

! !

!!

!

!


4/32

P/N 488M

P/N 4043

DONT FUEL, REFUEL,OR CHECK FUEL WHILESMOKING, OR NEAR ANOPEN FLAME OROTHER IGNITIONSOURCE.

MIX UNLEADED GASWITH 2 CYCLE 50:1OIL.

INCORRECT ASSEMBLY.CAUTION: WHEN ASSEMBLINGTHE HANDLES, MAKE SUREFUEL TANK FACES OPERATOR.THIS IS THE REAR OF THETILLER, REFER TO ASSEMBLYINSTRUCTION ON PAGE 7.

CUTTING HAZARD; KEEPFEET AND HANDS AWAYFROM ROTATING TINES.

WEAR EAR AND EYEPROTECTION.

READ OWNERS MANUALBEFORE USING TILLER, ORPERFORMING ANY REPAIROR MAINTENANCE. KEEPOWNERS MANUAL IN ASAFE PLACE.

DO NOT CARRY THETILLER IN THISPOSITION.

IV. Warnings - DosRead and understand the

owners manual. Pay

particular attention to allsections regarding safety.

1. Always keep a firm grip onboth handles while the tines aremoving and/or the engine is running.BE AWARE!! The tines may coastafter throttle trigger is released. Makesure tines have come to a completestop and engine is off before lettinggo of the tiller.

2. Always maintain a firm footingand good balance. Do not overreachwhile operating the tiller. Before youstart to use the tiller check the workarea for obstacles that might causeyou to lose your footing, balance orcontrol of the machine.

3. Thoroughly inspect the areawhere equipment is to be used andremove all objects, which can bethrown by the machine.

4. Always keep area clear ofchildren, pets, and bystanders.

5. Always stay alert. Watch whatyou are doing and use common

sense. Do not operate unit whenfatigued.

6. Always dress properly. Do not

wear loose clothing or jewelry, theymight get caught in moving parts.Use sturdy gloves. Gloves reduce thetransmission of vibration to yourhands. Prolonged exposure tovibration can cause numbness andother ailments.

7. While working, always wearsubstantial footwear and longtrousers. Do not operate theequipment when barefoot or wearingopen sandals.

8. Always wear ear and eyeprotection. Eye protection must meet

ANSI Z 87.1. To avoid hearingdamage, we recommend hearingprotection be worn whenever usingthe equipment.

9. To reduce fire hazard, keep theengine, and petrol/gas storage areafree of vegetative material andexcessive grease.

10. Start the engine carefully,according to the manufacturersinstructions and with feet well awayfrom tool(s).

11. Keep all nuts, bolts and screwstight to be sure the equipment is insafe working condition.

12. Use extreme caution whenreversing or pulling the machinetowards you.

13. Work only in daylight or goodartificial light.

14. Always be sure of your footingon slopes.

15. Exercise extreme cautionwhen changing direction on slopes.

16. Always keep a safe distancebetween two or more people whenworking together.

17. Always inspect your unit

before each use and ensure that allhandles, guards and fasteners aresecure, operating, and in place.

18. Always maintain and examineyour Tiller with care. Followmaintenance instructions given inmanual.

19. Always store tiller in asheltered area (a dry place), notaccessible to children. The tiller aswell as fuel should not be stored in ahouse.

WARNING DANGERIF THE TILLER IS USED IMPROPERLY OR SAFETY PRECAUTIONS ARE NOT FOLLOWED,

THE USERS RISK SERIOUS INJURY TO THEMSELVES AND OTHERS.

READ AND UNDERSTAND THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS TILLER.

! !

IMPORTANT ENGINE INFORMATION:

ENGINE FAMILY: SEH024UB24RD

DISPLACEMENT: 21.2cc

THIS ENGINE MEETS U.S.EPA PHI AND 1995-

1998 CALIFORNIA EMISSION REGULATIONS

FOR ULGE ENGINES. REFER TO OWNERS

MANUAL FOR MAINTENANCE

SPECIFICATIONS AND ADJUSTMENTS

KIORITZ CORP. A98

EMISSION CONTROL --The emission controlsystem for thisengine is EM(Engine Modification).

Emission Control Labellocated on Engine.EXAMPLE ONLY,information on label

varies by FAMILY).

An important part of the safety system incorporated in this tiller are

the warning and information decals found on various parts of the tiller.

These decals must be replaced in time due to abrasion, etc. It is your responsibility

to replace these decals when they become hard to read. The location and part

numbers (P/N) of these decals are illustrated on Page 27.

III. Safety Decal Information

4


5/32

V. Warnings - Don'tsDont use tiller with one hand.

Keep both hands on handles withfingers and thumbs encirclingthe handles, while tines aremoving, and engine is running.

Dont overreach. Keep a good

footing at all times.Dont run with the machine,

walk.

Dont work on excessivelysteep slopes.

Dont attempt to clear tineswhile they are moving. Never tryto remove jammed materialbefore switching the engine offand making sure the tines havestopped completely.

Dont allow children orincapable people to operate thistiller.

Dont operate while underthe influence of alcohol or drugs.

Dont attempt to repair thistiller. Have repairs made by aqualified dealer or repairman.See that only original Mantisparts are used.

5

WARNING DANGERHANDLE FUEL WITH CARE, IT IS HIGHLY FLAMMABLE. FUELING A HOT ENGINE OR NEAR AN IGNITION

SOURCE CAN CAUSE A FIRE AND RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.

! !

Always use fresh gasoline in thefuel mixture. Stale gasoline cancause damage.

Always store fuel in containersspecifically designed for thispurpose.

Always pull starter cord slowly

until resistance is felt. Then pullcord rapidly to avoid kickback and

prevent arm or hand injury.

Always operate engine withspark arrestor installed andoperating properly. The use of sparkarrestor mufflers is required by lawin the state of California (Section4442 of the California PublicResources Code), as well as in otherstates or municipalities. Federal

laws apply on federal lands.

Stop the engine whenever youleave the machine.

Allow the engine to cool beforestoring in any enclosure.

Ifthe fuel tank needs to bedrained, this should be done

outdoors.

Dont fuel, refuel or check fuelwhile smoking, or near an openflame or other ignition source.Stop engine and be sure it is coolbefore refueling.

Dont leave the engine runningwhile the tiller is unattended. Stopengine before putting the tillerdown or while transporting fromone place to another.

Dont refuel, start or run thistiller indoors or in an improperlyventilated area.

Dont run engine whenelectrical system causes spark

outside the cylinder. Duringperiodical checks of the sparkplug, keep plug a safe distancefrom cylinder to avoid burning ofevaporated fuel from cylinder.

Dont check for spark withspark plug or plug wire removed.Use an approved tester.

Dont crank engine with sparkplug removed unless spark plugwire is disconnected. Sparks canignite fumes.

Dont run engine when theodor of gasoline is present orother explosive conditions exist.

Dont operate the unit ifgasoline is spilled. Clean up spillcompletely before starting engine.

Dont operate your tiller ifthere is an accumulation of debrisaround the muffler, and coolingfins.

Dont touch hot mufflers,cylinders or cooling fins ascontact may cause serious burns.

Dont change the enginegovernor setting or over speedthe engine.

VI. Engine/Fuel Warnings - Dos

VII. Engine/Fuel Warnings - Donts


6/326

Your MANTIS Tiller comes partiallyassembled. You must install only thehandlebars, the carrying handle, and thetines. This will take just a few minutes ifyou follow the directions.

First, take all items out of thecarton. But do not remove the cardboard

from around the Tillers base.The list at the right, shows the parts

that come with your tiller. Check to makesure you have them.

The bag of hardware is in the plasticbag containing the Owners Manual.

To assemble your MANTIS Tiller, youllneed two 7/16 wrenches or twoadjustable wrenches. We suggest that youinstall all nuts and bolts only fingertight that is, one-half to one fullturn until youve completedassembly. The nuts are self locking,but you must use a wrench to tightenthem completely.

ASSEMBLY

WARNING DANGER

IMPROPER ASSEMBLY OF THIS TILLER

CAN RESULT IN SERIOUS INJURY.MAKE SURE TO FOLLOW ALL

INSTRUCTIONS CAREFULLY.

IF YOU HAVE ANY QUESTIONS

CONTACT OUR FACTORY AT

1-800-366-6268

OR AN AUTHORIZED

MANTIS DEALER

! !

Quantity Description *Key #

1 Upper Handle Assembly 4A1 Upper Handle Throttle Side Assembly 5A2 Lower Handles 61 Pair Tiller/Cultivator Tines 39/40

1 Engine Assembly (includes FenderGuard & Worm Gear Transmission) 20, 21, 55

1 Handle Brace 81 Plastic Carrying Handle 421 Bag of Hardware Containing:2 Cap Screws 47*4 Lock Nuts 48*2 Bolts (3 long) 49*2 Tine Retaining Pins 41*2 Handle Clamps 51*1 Throttle Clips 13*

2 Bolts 52*2 Knobs 53*

*These numbers are the same numbers shown on the PartsLayout on page 27.


7/32 7

ASSEMBLY (continued)

HOW TO ASSEMBLELOWER HANDLES

To identify part numbers, seepages 6 and 27.

1. Use the protectivecardboard sleeve to stabilize

your tiller. Stand the engineassembly (#21) up.

2. Lay the handle parts withineasy reach. Youll need one of thehandle clamps (#51) and one ofthe lower handles (#6). Note thatthe lower handles have a short legon one end. (Picture 1)

3. Fit the handle clamp along

the outside of the short leg. Lineup the holes on the clamp and theleg.

4. Choose one of the two 3-inchbolts (#49). Slide it through thefirst set of holes near the elbowwhere the lower handle curves.(Picture 2)

5. Now slide the other lower

handle onto the 3-inch bolt.(Picture 3.) Fit the other clamponto this other handles short leg.Add a nut and tighten finger tight.

6. Locate the worm gear

housing. It starts just above andextends down through thetillers red fender guard. Youllnotice that theres a recessedchannel on either side of thehousings top. (Picture 4.)

7. Take the lower handles thatyouve just put together. Slidethem into the two recessedchannels.

Make sure you insert themfrom the rear of the tiller (gasolinetank faces the operator) . . . so thatthe bolt fits along the back of thehousing. (Picture 5)

8. Slide the second 3-inch boltthrough the second set of holes inthe short legs. Add a nut andtighten finger tight.

Picture 1

Picture 2

Picture 3 Picture 4 Picture 5

NOTE: THE LOCK NUTS ARE STAMPED. FINGER TIGHT ISAPPROXIMATELY 1/2 TO 1-1/2 TURNS.

!


8/328


WARNING DANGERREMOVE TINES BEFORE STARTING ENGINE

AND MAKING ADJUSTMENTS.

! !

HOW TO ASSEMBLEUPPER HANDLES &PLASTIC CARRYINGHANDLE.

1. Lightly squeeze the lowerhandles (#6) toward oneanother so that they line upwith the two smaller holes onthe carrying handle (#42). Thenslide the carrying handle overand down the lower handles. Itwill rest about four to six inchesabove the engine. (Picture 1)

2. Gently pull the lowerhandles out to their originalposition.

3. Attach the upper handleassembly (#5A) the handlewith the throttle cable andground wire onto eitherhandle, and secure

with the handle knob (#53). Youcan attach this upper handle towhichever lower handle youprefer, depending on whichhand youd rather use tosqueeze the throttle. (Picture #2)

Note: If throttle handle ismounted on the left, it will notfold down as completely aswhen mounted on the right.) Besure you have proper throttlemovements and that thethrottle cable is not wrappedor twisted around the handlebar. Squeeze trigger and let go.The triangle must click in bothdirections. If there is any doubt,

remove air filter and visuallycheck that the throttle trianglehits both the idle screw and thefull open stop. THIS MUST BEDONE BEFORE STARTINGTHE ENGINE.

4. Follow the same steps toinstall the other upper handleonto the other lower handle.(Picture 3)

5. Use the clip (#13) to securethe throttle cable and wire inplace on the lower handle.(Picture 4)

6. Now install the Handle

Brace. Line it up with the holeson the upper handles. Theninsert a Cap Screw and a LockNut on either side (Picture 5)

7. Use a wrench to tightenCap Screws and Lock Nuts.

8. Now use wrench to tightenall nuts and bolts firmly andsecurely.

IMPORTANT NOTE:

Make sure you haveinstalled the handlesproperly. When you standbehind your tiller, holdingthe handles, you shouldface the gasoline tank.

Picture 3Picture 2

Picture 1

Picture 4 Picture 5

WARNING: Improper throttle installation can causetines to rotate unexpectedly .

!


9/32 9


WARNING DANGERFUEL IS EXTREMELY FLAMMABLE. HANDLE IT WITH

CARE. KEEP AWAY FROM IGNITION SOURCES. DO NOT

SMOKE WHILE FUELING YOUR EQUIPMENT.

Assembling the Tinesfor Tilling

1. Remove the cardboardfrom around your Tillers base.

2. Slide the tines onto theaxle shafts. The D hole goeson the outside.

3. Make sure youve installedthe tines properly for tilling.Liken the tines to your fingers.When your palm faces theground, your fingers curl down.Stand behind the Tiller andhold your hand next to thetines. Do the tine blades curl

down, as your fingers do? If so,they are in the tilling position.(To switch to the cultivatingposition, see page 15.)

4. To secure each tine to theaxle, insert a tine retaining pin.

IMPORTANT NOTE:

Before you use your

MANTIS Tiller, read theSafety Rules & Warningson pages 3-5.

Heres how to mix one gallon offuel:

1. Pour 1/2 gal. of the gasolineinto a safe container. Do not mixthe fuel and oil in the enginefuel tank.

2. Add 2.6 ounces of two-cycle engine oil to the gasolineand mix. Then add the rest of

the gasoline.(1/2 gal.)3. Screw the cap onto the

gasoline can. Then swirl the canto blend the oil and gas.

4. Carefully pour the fuel mixinto the tillers fuel tank. Afterputting the fuel tanks cap backon, wipe up any spilled fuelfrom tank and gasoline can.

IMPORTANT:

Two stroke fuel separates andages. Do not mix more than youwill use in a month. Using oldfuel can cause difficult startingor engine damage. Shake fuelcontainer to thoroughly mix fuelbefore each use. Do not attemptto run your engine on gasolineonly, use proper fuel mixture.

Need more pre-measuredengine oil? Contact your localauthorized Mantis Dealer.

Remember

Always mix two-cycle oil withgasoline before fueling yourtiller. Never, ever run your tilleron gasoline alone. This will ruinyour engine and void allwarranties.

Always use a clean gas can andalways use unleaded gas.

Never try to mix the oil andgasoline in the engine fuel tank.

Always mix oil and gas in theproper proportions: 2.6 ouncesof two-cycle engine oil to onegallon of unleaded gasoline.

IMPORTANT NOTE:

Do Not use old or staleoil/gasoline mixture.

Always use the properoil/gasoline mixture. If youdo not, your engine willsuffer rapid, permanentdamage.Andyou will voidthe engine warranty.

! !

Mixing FuelYour MANTIS Tiller is powered by

a commercial two stroke, air cooledengine which requires a fuel mixtureof gasoline and lubricating oil.

Use a mixture of 50 parts unleadedregular gasoline and 1 part two-strokeMANTIS oil (50:1.) Use branded 89 octane (R+M+2) unleaded gasolineor gasohol (maximum 10% ethyl alcohol, or 15% MTBE, no methylalcohol.)

1 gallon

2.6 oz. bottle ofMantis 50:1 2-cycle engine oil


10/3210

Never use startingfluids as they will

cause permanentengine damage.Using them will

void the warranty.

Before you use thetiller, read theSafety & Warningrules on pages 3-5.

WARNINGAVOID ACCIDENTAL

BLADE ENGAGEMENT

DO NOT SQUEEZE THE

THROTTLE TRIGGER

WHEN STARTING.

MAINTAIN PROPER IDLE

SPEED ADJUSTMENT

(2500-3100 RPM)

! !

Picture 4

Picture 5


STARTING

To Start Your Tiller forthe First Time:

1. Fill the fuel tank with theproper oil/gasoline mixture.(See previous section.)

2. Hand tighten the gasolinecap just until its snug.

3. Place the start/stop switchinto the start position.(Picture 1)

4. Pull the choke button allthe way out, to completely closethe choke. (Picture 2)

5. Locate the purge bulb onthe upper right of the engine, in

front of the fuel tank. (SeePicture 3) It sends fuel into thecarburetor, for easy starting.Press the purge bulb until yousee fuel flow through the clearfuel return line. Since yourestarting cold, you may need topress six to eight times. As soonas fuel starts flowing throughthe clear fuel line, stop pressing!(Picture 3)

6. Dont press the throttlelever during the starting of theengine.

7. Pull the starter cord(Picture 4) until resistance isfelt. Then give the recoil starter

cord a few brisk pulls until theengine fires. Note: Pull thestarter cord about 12" to 18".During cold starting, you mayneed to pull at least three or

four times before the enginefires.

NOTE: When the choke isclosed, never pull the cord morethan four or five times.Overpulling may cause flooding.Also, bear in mind that, whenthe engine fires, it only coughsor sputters, and will not runon choke.

8. Push the choke button in,

all the way, to open the choke.(Picture 5)

9. Then pull the starter cordagain. The engine should startand run. Let the engine warmup two to three minutes beforeusing.

Follow these steps whenever youare starting the engine cold, orwhen the engine has run dry andyou have just added fuel.Remember, always use short, briskpulls. Dont give the cord a long,forceful yank.And, do not let thecord snap back into the starterhousing.


11/3211

Starting a WarmEngine

1. Toggle ignition switch toSTART position.

2. Push choke button in tothe RUN (open) position.

3. If there is no fuel in the

clear return line, push primerbulb 3-4 times or until fuel isvisible in the line.

4. Pull starter rope usingshort pulls, 1/2 to 2/3 of the

rope length.5. If engine fails to start in 4

pulls, use First Time starting

procedure on page 10.

6. With engine running, andboth hands on the handles,squeeze throttle triggergradually to increase the engine

speed and engage the tines.

How to Stop theEngine

Simply toggle the start/stopswitch to stop. (Picture 1)This will stop the engineinstantly. If it should ever fail todo so, just pull out the chokebutton. The engine will stop atonce.

About the ChokeThe choke controls the

amount of air drawn into theengine. Your tiller will run only

if the choke is open that is, ifthe choke is pushed in.

A Special Feature

(with the idle setproperly and theengine running)

Even when the engine isrunning, the tines wont turnunless you press the throttlelever on the handlebars. And,when you release the throttlelever, the tines will stop.

A Tip for ExtendingYour Engines Life

After you start the engine, letyour tiller warm up for two tothree minutes before you use it.Then, before you put your tiller

away, let it idle for a minute togive the engine a chance to cooldown.

WARNING DANGER

IF ENGINE DOES NOT STOP WHEN SWITCH IS PUT IN THE STOP

POSITION, RELEASE THE THROTTLE, ALLOW ENGINE TO IDLE.

PUT THE TILLER DOWN, AND PULL THE CHOKE BUTTON OUT

TO COLD START (CLOSED) POSITION.CHECK AND RETURN IGNITION SWITCH TO ON POSITION

BEFORE STARTING ENGINE AGAIN.

Picture 1

STARTING (continued)

ADDITIONAL INFORMATION

! !


12/3212

If you follow the normalstarting procedure, you shouldhave no problem starting yourtiller. But, just in case you dohave problems, heres what to do.

Make sure the start/stopswitch is on start. Youd besurprised how many peopleforget to toggle the switch intothe start position.

If the switch was on stopwhen you pulled the cord, youmay have flooded the engine.

First, examine the spark plug.Use the special wrench thatcomes with our optional

MANTIS Handy Item Kit (Item#8444) or a 3/4 inch spark plugwrench. (Picture 1)

Remove the cap over the sparkplug.

Unscrew the spark plug.(Picture 2)

Starting a Flooded

Engine1. If the end of the spark plug

is wet, the engine may be

flooded. Make sure the switch

is in the stop position,disconnect spark plug wire andremove plug. Use a paper towelor a clean rag to dry the sparkplug, then, with the spark plugout of the engine, pull thestarter cord several times.Next, replace the spark plug. Usethe wrench to tighten it andreplace the cap. Next, put theswitch in the start position andpull the choke button out. Pullthe starter cord three or fourtimes until the engine coughs orsputters. Open the choke (pushthe choke button in) and pullthe cord a few times. The engine

should start and run.2. If the end of the spark plug

is dry, check to see if the fuelline is blocked. First loosen thefuel cap to relieve pressure in thetank. The fuel line runs fromthe fuel tank to the carburetor.Pull it off at the carburetor end.Fuel should drip slowly from theline. Wipe off any excess orspilled fuel.

If fuel does not drip from theline, check the line for any bendsor pinches. (Picture 3). Kinks inthe line restrict the flow of fuelto the engine. Just straighten outthe line. Reconnect. Then followthe normal starting procedure.

If fuel drips too freely, the linemay be disconnected from thefuel filter. Youll find the fuelfilter inside the fuel tank. Just re-

attach the line to the filter, andput the filter back in the tank.Then follow the normal startingprocedure.

Heres Another Way toStart your MANTISTiller

If you follow the steps aboveand your engine still wont start,try this:

1. Push the switch to start.

WARNING

MAKE SURE THE START/STOPSWITCH IS IN THE

STOP POSITION.

KEEP PLUG WIRE AWAY

FROM ENGINE TO AVOID

UNINTENTIONAL SPARK.

IMPORTANT NOTE:

To avoid possible damage

to the threads, do not tryto remove the plug from ahot aluminum cylinderhead.

WHAT TO DO JUST IN CASE

! !

Picture 1

Picture 2

Picture 3


13/3213

2. Push in the choke buttonto open the choke.

3. Press the plastic bubble afew times.

4. Give the starter cord a few

short, quick pulls. The engineshould start and run.

5. If the engine does not start,then pull out the choke buttonto close the choke. Pull thestarter cord four to five times.The engine should sputter orcough.

6. After the engine sputters,push the choke button in. Thenpull the starter cord. The engineshould start and run.

7. If the engine still does not

start, repeat steps 2 through 6.8. If the engine still does

not start, call 1-800-366-6268and ask for Customer Serviceor the name of your localMANTIS dealer.

IMPORTANT NOTE:

Never use starting fluids.Starting fluids will causepermanent enginedamage. Using them will

void the warranty.

IMPORTANT NOTE:

Before you use yourMANTIS Tiller, read theSafety Rules & Warningson pages 3-5.

WHAT TO DO JUST IN CASE (continued)

GETTING YOUR TILLER TO YOUR GARDENWalk it.

Once your tiller is running,you can walk it to yourgarden. Just press the throttlelever gently and let the tillertip-toe across your yard on itstines. It wont hurt your lawn ordriveway. (Picture 1)

Carry It.Make sure the engine is off.

Then use one hand to grasp the

convenient carrying handle. Usethe other hand to hold thehandlebars. (Picture 2) Then liftyour tiller and carry it to yourgarden. Since it weighs only 20pounds, it wont strain yourmuscles or tire you out!

Take It for a Ride.You can easily transport your

MANTIS Tiller to a friends orrelatives house. Just empty thefuel tank. (This is crucial.)

Then stow your Tiller in thetrunk of your car or truck. Itfits easily. And you can put it inand take it our withoutstraining your back.

WARNING

NEVER CARRY YOUR TILLERAS THE PERSON IN PICTURE 3

IS DOING. IF YOU DO,

YOU WILL SUFFER

SERIOUS INJURY.

! !



14/3214

Now Youre Ready toUse Your MANTIS Tiller.

If youve seen other tillers,your MANTIS Tiller may surpriseyou. It tills best when you pull itbackward! You see, when you

pull your MANTIS Tillerbackward, you give extraresistance to the tines, so theydig deeper.(Picture 1)

Whats more when you gobackward, you erase yourfootprints. So your soil stays lightand fluffy. With other tillers, bycontrast, you walk right over thesoil youve just tilled, packing it

down, so its less plantable.

Run Your MANTISTiller like a VacuumCleaner.

Place your Tiller at the head ofthe row or area you want to till.Start it up. Then use an easyrocking motion. First, pull your

Tiller backward. Then use aneasy rocking motion. Again, pullyour Tiller backward. Then, let itmove forward just a little bit.Then pull it backward again.This will help you till deeper.

Keep repeating these stepsuntil youve tilled an entire row.Start again on the next row. Itsmuch like running a vacuumcleaner! (Picture 2)

You Can Even ControlDepth.

For Deeper Tilling:

Move your Tiller slowly backand forth, as you would a vacuumcleaner. Work the same area over

and over until youve dug to yourdesired depth. (Picture 3)

For Shallow Tilling:

Switch the tines to thecultivating position. (See page15 to learn how.) Then moveyour Tiller quickly over yoursoil surface.

For Big Weeds or Tough Roots:

Let your Tiller rock back andforth over the tough spot, untilthe tines slice through the weedor root.

Your MANTIS TillerHandles Special TillingProjects.

Want to turn part of your lawninto a colorful flower border?Your MANTIS Tiller makes iteasy! Just run your Tiller backand forth until the sod begins tobreak up. Then continue tilling.Your Tiller will chop the clumpsof sod until theyre fine. Then, itwill work them into the soil.Pretty soon, youll have a soft,fresh planting bed.

WARNING DANGER

THE OPERATOR OF THIS TILLER IS RESPONSIBLE FOR

ACCIDENTS OR HAZARDS OCCURRING TO HIMSELF,

OTHER PEOPLE OR THEIR PROPERTY.

TILLING

Picture 1

Picture 2

Picture 3

!!


15/3215

TILLING/CULTIVATING

How about a family-sizevegetable garden?

Nowadays many gardenersprefer small gardens especially in the suburbs, wherespace is at a premium. But, if

youre fortunate enough to owna large lot, you can create abigger garden a half acre ormore. Heres how:

1. First, hire someone with atractor or big tiller to breakground for you. This is a one-time-only investment thats wellworth the small cost.

2. Then, use your Tiller tobreak up any remaining clumpsof soil or sod. Unlike a tractoror big tiller, your MANTIS Tilleris a precision tool. It willpulverize your soil into asmooth seed bed.

Your MANTIS TillerMakes Weeding aPleasure!

As a tiller, your MANTISTiller works the soil down to10 (25.4 cm) deep. But, as acultivator, it gently cultivatesthe surface, only 2 to 3 (5.09cm to 7.62 cm) deep.

First, you must change thetines to the weeding position.This takes less than a minute.

Then, your MANTIS Tillers

sharp tine teeth will slice upthose pesky weeds, buryingthem as you go along. And,since the tines in this positionwont dig too deep, they wonthurt your plants precious rootsystems.

The result? Your Tiller willcut your weeding time in half,and turn a tiresome chore into apleasure.

How to Switch FromTilling to CultivatingPosition

1. Make sure your Tiller ofoff.

2. Remove the retaining pinsfrom the tines.

3. Remove the tines from theaxle.

4. Place the right-side tineonto the left-side axle. Place theleft side tine onto the right-sideaxle. The D hole should be to

the outside.5. Here is how to make sure

youve installed the tinesproperly. Stand behind the Tillerand hold your hand, palm up,next to the tines. Do the tinepoints curl up, as your fingersdo? If so, they are in the correctcultivating position.

6. Reinsert the pins.

WARNING DANGER

IF YOUR TINES GET JAMMED OR ENTANGLED, SHUT OFF THE ENGINE AT ONCE.

REMOVE THE SPARK PLUG WIRE THEN REMOVE THE OBSTRUCTION

WHILE THE ENGINE IS OFF. NEVER TRY TO REMOVE AN OBSTRUCTIONWHILE THE ENGINE IS RUNNING. SERIOUS INJURY CAN RESULT.

! !

Picture 1 Picture 2


16/3216

Now Youre Ready toCultivate or Weed.

Guide your Tiller where youwant to weed and start it up.Pull your Tiller backward

slowly, then let it move forwarda bit, in a gentle rockingmotion. Watch it slice, shred,and bury those weeds!

Got tough weeds? Lightenyour pressure on the throttle toslow your Tiller down. Thenwork back and forth until yourTiller chops up the weeds. Itseasy and effective!

Remember, any tiller willtangle in tall grass, stringyvines, or super-big weeds. So, ifyou have a backyard jungle,first use a knife, pruner, orbrush cutter to chop up theovergrowth. If the tines becometangled anyway, toggle theswitch to the stop positionto turn the engine offcompletely before trying to

clear them.

Your Mantis TillerWill Weed BetweenNarrow Rows!

Your Mantis Tiller is aprecision weeder that easily fitsin tight places. So dont be

afraid to weed anywhere:between plants and shrubs; incorners; against fences; onraised beds; in wide rows; evenin very narrow rows. YourMantis Tiller weeds six* to nineinches wide. So you can run itin a tightly planted gardenwithout damaging your delicate

CULTIVATING

Tilling PositionTine teeth point in the same

direction as the rotation of thetine; or toward the front of theTiller, away from the operator.

Cultivating PositionTine teeth point in the

opposite direction as therotation of the tine. Tines pointtoward the back of the tiller, ortoward the operator.

plants. Thats good news forsuburban gardeners, who oftenhave to plant rows closetogether!

*With optional PlanterFurrower attachment(Item #6222.)


17/3217

MAINTENANCE

Check the Air Filter OftenA wet or dirty air filter can

affect the way your engine starts,performs, and wears. So, its agood idea to check your air filter

once a month.

If you work in dusty soil, or ifyou want to be on the safe side then check your filter moreoften (for instance, before eachuse). But be sure to replace it atleast once a year, in the spring orfall. Clean or change it asneeded. It is recommended tochange the air filter yearly.

How to Check, Clean andChange the Air Filter

1. Loosen the wing nut on theside of the air-cleaner cover. (SeePicture 1, or look up Key #9 inAir Cleaner Parts Assembly onpage 28.)

2. Take off the cover. Makesure to clear the choke button.

(Picture 2)

3. The air filter is the whitepad on the inside of the air-cleaner cover. Check whether itis soiled or moist.

4. If the air filter needscleaning or no longer fitsproperly, remove it. Just lift anedge carefully and peel it out.(Picture 3)

5. Use a brush to removedebris from the pad.

6. If the air filter is so dirtythat it wont come clean, youmust replace it or severe enginedamage will occur. Order a newone directly from your localAuthorized MANTIS Dealer.

7. Insert your clean filterinside the air-cleaner cover.

IMPORTANT! Make surefilter is seated properlyin the cover. The filtermust fit snugly inside therim that holds the filter inplace.

Installing the filter incorrectly

will cause engine damage and

void the warranty. Fit the cover

back over the air cleaner. (Again,

make sure to clear the choke

button.)

8. Tighten the wing nut tosecure the cover.

Note:

Please check the lipon the Air CleanerCover. If the lip is

chipped or cracked,it should bereplaced. This willprevent dirt frombeing ingestedthrough thecarburetor into theinside of the engine.

Picture 1 Picture 2

Picture 3


18/3218

How to Check the GreaseLevel Inside the

Worm Gear HousingWhen we built your MANTIS Tiller,

we lubricated the worm gear housingthoroughly.

It is imperative that you inspect thegrease level once a year. Simplyremove the cover plate on the wormgear housing. (Picture 1) Then checkto make sure the grease comes almostto the top of the housing. If it doesnt,add lithium #0 grease (Item M9985.)This is the only way to add grease tothe worm gear housing. (Picture 2) To

purchase MANTIS grease, contactyour local authorized MANTIS dealer.

Please do not overfill. Too muchgrease can create pressure, whichcould cause seals to fail or the clutchto slip.

Clear Blockages From theFuel Line & Filter:

After youve used your Tiller for a

few seasons, check for blockages inthe fuel tank and fuel filter. Suchblockages can keep your Tiller fromstarting.

Clear any blockages you see in thetank, fuel filter, or fuel line.Remember: The fuel filter is locatedinside the tank. (See Picture 3) Thenuse the normal starting procedure tostart your Tiller.

MAINTENANCE (continued)

Picture 1

Picture 2

Picture 3


19/3219

What to Do if YourEngine Idles Too High

What if your engine runs toofast or if the tines turn theinstant you start the Tiller? Youmay need to adjust the idlescrew (Key #31 underCarburetor on page 28) by itselfright below the H and L screws.

Gently turn it counter-clockwise. Youll know youveadjusted it correctly when theaxles do not turn at low idle.

If you continue to have idleproblems, you may need toadjust the throttle cable.

First, locate the metal triangleat the end of the throttle cable.(Picture 1) The idle screw musttouch this triangle. But, if thethrottle cables too tight, youllsee a gap between the idle screwand the triangle.

To fix this, loosen the top nutthat holds the throttle cable inplace. (Picture 2) (Use a 10mm

wrench or an adjustablewrench.) Then, slide the cabledown until you close the gapbetween the triangle and theidle screw. (Picture 1) Now,

tighten the bottom nut thatholds the throttle cable.

Locate the metal button onthe triangle. This is the swivel.The large end of the throttlecable must be inside the slot inthis swivel. (Picture 3)

What to Do if YourEngine Runs Rough

If your engine runs roughor stalls, you may need to adjustthe carburetor and idle screws.

If you remove the air-cleanercover, youll see the twocarburetor, adjustment screwsnext to the black choke button.

The RED screw is theHIGH-speed adjustmentTheWHITE screw is the lowspeed adjustment.

First, remove the tines fromthe axle. Then start engine. Letit run for two to three minutes.

FLASH the choke severaltimes during the warm-up toclear any air from the Fuelsystem.

Then stop the engine after it

reaches operating temperature.Now, turn the RED, high-

speed screw counter-clockwiseall the way to stopThen turnthe WHITE, low speed screwhalfway between the counter-clockwise and clockwise stoppositions.

Now restart the engine tofinish the carburetor

adjustment.Run the engine at full speed

two or three seconds to clearout any excess fuel. Then returnto idle.

Now, accelerate the engine tofull throttle several times tocheck for a smooth transitionfrom idle to high speed.

If the engine hesitates turn

the WHITE, low-speed screwcounter-clockwise one-eighth ofa turn. Then accelerate theengine.

Repeat the adjustment untilyou get a smooth transition tohigh speed.

WARNINGDANGER

REMOVE TINES BEFORE

STARTING ENGINE AND

MAKING ADJUSTMENTS


! !



20/3220

How to Reseat theFlange

At some point, you may findthat the tines wont turn whenyou press the throttle. This

may mean the engine isntsitting all the way down on theworm gear housing.

Perhaps youve been usingyour Tiller for several years.Or perhaps youve removedthe engine for use with ourhedge trimmer attachment,then replaced it. In either case,the flange bolt (Key #36, page

29) may have come loose andlifted the engine up.

If this happened youllnotice a gap between thebottom of the engine flange(Key #37, page 29) and thetop of the worm gear housing.(Picture 1)

To fix this, loosen the flangebolt. Take the engine off theworm gear housing. Noticethe hex head on top of thedrive shaft (Key #22, Page 27).

Inside the flange housing,youll find the clutch drum(Key #29, Page 29). Make surethe hex head lines up with theclutch drum inside the flangehousing.

Then put the engine backon the worm gear housing.Make sure the plastic carryinghandle is not under the fueltank.

If youve followed these stepsproperly, there will be no gapbetween the engine flange andthe worm gear housing.(Picture 2) Make sure youtighten the flange bolt!

Picture 1 Note how theengine doesnt sit all the waydown on the transmission.

Picture 2 Note how theengine sits all the way down onthe transmission.


Cleaning the MufflerScreen

1. Take out the spark plug.

2. Remove the red cylindercover, (Key #32) which is heldon by 1 phillips-head screw,(Key #33) and 1 hex-headscrew, (Key #34) which youwill need an allen wrenchto remove.

3. You will see the metalexhaust guide, held on by 3more phillips-head screws.

(Key #25) Remove the exhaustguide.

4. Behind the exhaust guide(Key #24) will be the mufflergasket (Key #23) and mufflerscreen (Key #22). The screensits under the gasket.

5. If the screen (Key #22) is

clogged with deposits, it needsto be cleaned. Use carburetorcleaner, and any brush that isnot metal.

Brush the screen until you areable to see through it.

6. If the screen remainsplugged after attempts atcleaning, it must be replaced.

WARNINGDANGER

DO NOT USE

GASOLINE OR OTHER

FLAMMABLE SUBSTANCE

! !


21/3221

STORAGE

Each fall or before youstore your Mantis Tiller forany long period be sure totake these measures:

1. Do not store your Tillerwith fuel still in it. Even underideal conditions, stored fuel

containing ethanol or MTBEcan start to go stale in 30 days.And, since stale fuel has ahigh gum content, it can clogthe carburetor, this, in turn,will restrict fuel flow. So,

when youre ready to storeyour Tiller, or will not beusing it for more than 2

weeks, drain the fuel tankcompletely. (Picture 2)

2. Next, restart the engineto make sure no fuel is left inthe carburetor. Then run theengine until it stops. This willprevent gum deposits, forminginside of the carburetor andpossible engine damage.

3. Disconnect spark plugwire and remove the sparkplug. (Use the wrench thatcomes in our optional Handyitem Kit, Item #8444. Or use a19mm or 3/4 spark-plugwrench.) Pour about ateaspoon of clean, air-cooled,two-cycle oil through thespark-plug hole into thecombustion chamber. (Picture 3)Leaving the spark plug outslowly pull the starter cordtwo or three times to coat the

inside of the cylinder wall.

4. Inspect the spark plug, and,if necessary, clean it. If youneed to replace it, buy a

NGK-BPM8Y. A replacementspark plug is included in theoptional Handy Item Kit item# 8444.

5. Install the spark plug, butleave the spark plug wiredisconnected.

6. Clean the air filter asdescribed on Page 17.

7. Clean dirt, grass, and

other materials from the entiremachine.

8. Wipe the tines with oil orspray them with WD-40, toprevent rusting.

9. Oil the throttle cable andall visible moving parts. (Donot remove the engine cover.)

WARNINGDANGERDO NOT STORE IN AN AREA

WHERE FUEL FUMES MAY

ACCUMULATE AND REACH AFLAME OR SPARK.

! !

Picture 1

Picture 2

Picture 3


22/3222

STORAGE (continued)

Picture 1

Picture 2

Picture 3

10. Check the grease level in theworm gear housing, as describedon page 18.

11. Order new parts toreplace any that are badly

worn or broken. Just call1-800-366-6268 and ask for a localauthorized Mantis dealer.

12. Store your Tiller, in anupright position, in a clean, dryplace. You can store with thehandles in an extended position orfolded down. (Picture #1,preceding page)

13. To fold the handles, follow

these easy steps: Loosen thehandle knobs (#53), fold thehandles forward (see picture #1,inset, preceding page). Tightenknob securely. Your handles arenow folded and ready to store in asmaller area.

14. Do you have fuel left overfrom last season? Dispose of itproperly. Buy fresh oil and gasolinenext season.

How to Prepare YourMANTIS Tiller forRestarting

Unfold the handles into an up-right or extended position. Tightenthe two handle knobs (#53)

In the Spring, when you take yourTiller out of storage, remove thespark plug. Pull the starter cordthree or four times to clean oilfrom the combustion chamber.

(Picture 1) Wipe oil from thespark plug. Place the spark plugback into the cylinder. Re-connectthe spark plug wire back on thespark plug. Then follow the steps

on pages 9 & 10 to refuel andrestart your Tiller.

Again, Check theCarburetor.

If your Tiller wont restart in theSpring or if it lacks its usualpower the carburetor may needattention. Follow the steps onpage 19 for adjusting the H and Lscrews. (Picture 2)

Check the Spark PlugToo.

If your Tiller wont restart, or ifit lacks full power, the spark plugmay be at fault. Check to see if theplug is fouled with oily blackdeposits. Clean or replace it if it is.(Picture 3)

Also, check whether the center

electrode is rounded at the end,or if the ground electrode is worn.If either is the case, you shouldreplace it with a NGK-BPM8Yspark plug. Use a 19mm or a 3/4spark-plug wrench to install it.Adjust the plug gap .024 - .028 in.(0.6 to 0.7 mm)

Caution: Do not overtighten the plug. The correct

torque is 18 to 22 ft.-lbs.(24-30 n.m)

IMPORTANT NOTE:

To avoid possible damageto the threads, do not try toremove the plug from a hotaluminum cylinder head.

Warning

Always make sure the handle

knobs are secure beforestarting your Mantis Tiller.

!!


23/3223

TROUBLE SHOOTING

1. Tines dont turn when throttleis depressed

Engine is not seated properly onthe gear housing.

Re-install engine following theinstructions on page 20 (How tore-seat the flange).

2. Engine fails to start Start/Stop switch is in Stopposition.

No fuel in tank.Fuel strainer clogged.Fuel line clogged.Spark plug shorted or fouled.Spark plug is broken (cracked

porcelain or electrodes broken)Ignition lead wire shorted,

broken or disconnected from

spark plug.Ignition inoperative

Move switch to start.

Fill Tank.Replace Strainer.Clean fuel line.Install new spark plug.Replace spark plug.

Replace lead wire or attach tospark plug.

Contact your local authorizeddealer.

3. Engine hard to start. Water in gasoline or stale fuelmixture.

Too much oil in fuel mixture.

Engine under or over choked.

Carburetor out of adjustment.Gasket leaks (carburetor or

cylinder base gasket).Weak spark at spark plug.

Drain entire system and refillwith fresh fuel.

Drain and refill with correctmixture.

If flooded by over choking,proceed according toinstructions in operation

section. If under choked, movechoke lever to closed positionand crank two or three times.

See Carburetor AdjustmentReplace gaskets.


6. Engine misses. Dirt in fuel line or carburetor.Carburetor improperly adjusted.Spark plug fouled, broken or

incorrect gap setting.Weak or intermittent spark at

spark plug.

Remove and clean.See Carburetor Adjustment.Clean or replace spark plug - set

gap to .024-.028 in. (0.6-0.7 mm )Contact your local authorized

dealer.

Problem Cause Remedy

4. Engine continuously floods. Fuel tank vent line is not in anupright position.

Return the fuel tank vent line tothe upright position and placeit under the cylinder cover in

the small pocket in thecylinder cover

5. There is black smoke comingfrom exhaust

The muffler screen is clogged Clean carbon from muffler screen(page 20)


24/3224

7. Engine lacks power. Air filter clogged.Carburetor out of adjustment.Muffler clogged.Clogged exhaust ports.

Spark Arrestor Clogged.Poor compression.

Clean or replace air filter.See Carburetor Adjustment.Clean carbon from muffler.Remove muffler, rotate engine

until the piston is at top ofcylinder. With a woodenscraper or blunt tool, removeall carbon from exhaust ports.Be careful not to scratch ordamage piston or cylinderwalls. Blow out all loose carbonwith compressed air. Installmuffler and gasket.

Clean Spark ArrestorContact your local authorized

dealer.

8. Engine overheats. Insufficient oil in fuel mixture

Air flow obstructed

Mix fuel as described in startinginstructions.

Clean flywheel cylinder fins andscreen.

9. Engine noisy or knocking. Spark plug in incorrect heat range.Bearings, piston ring or cylinder

walls are worn.

Replace with plugs specified forengine.


10. Engine stalls under load. Carburetor adjustment too lean.Engine overheats.

See Carburetor Adjustment.Remove dust and dirt from

between fins.

Problem Cause Remedy

TROUBLE SHOOTING (continued)

ENGINE SPECIFICATIONSDry Weight 2.8kg 6 lbs., 3 ouncesType of Engine Air Cooled, Two stroke, Single-Cylinder, Gasoline EngineRotation Clockwise, viewed from TOPBore 32.2 mm (1.268 in.)Stroke 26.0 mm (1.04 in.)

Spark Plug NGK BPM8YFuel Premixed two stroke fuelFuel Oil Ratio 50:1 ratio with MANTIS oilGasoline Unleaded (see page 9)Displacement 21.2 cc (1.294 cu. in.)Exhaust System Spark arrester mufflerCarburetor ZAMA diaphragm model C1U typeIgnition System Flywheel magneto, capacitor discharge ignition typeStarter Automatic rewind typeOil Designated, two-stroke, air-cooled engine oilFuel Tank Capacity 0.5 lit. (17.0 oz.)


25/3225

SERVICE MAINTENANCE GUIDE

Area Maintenance Frequency

Air Filter Clean Daily or every 4 hrs. use

Replace Every 3 mths. or 90 hrs. use

Spark Plug Clean Every 3 mths. or 90 hrs. useReplace 6 months or 270 hrs. use

Carburetor Check / Rebuild 6 months or 300 hrs. use

Replace Yearly or 600 hrs. use*

Cylinder Exhaust Port Inspect / Clean Every 3 mths. or 90 hrs. use

Cooling System Inspect / Clean Before Use

Muffler (Spark Arrestor) Inspect / Clean Monthly

Gear Housing Check Grease Yearly

Blades Inspect / Clean / Lubricate After Use

Fuel Leaks Inspect / Repair Before Use

Fasteners Inspect / Tighten / Replace Before Use

Labels Inspect / Replace Before Use

Handles Inspect / Replace Before Use

Guards / Safety Devices Inspect / Replace Before Use

Fuel Line Inspect / Replace Monthly

Starter Rope Inspect / Replace Monthly

Fuel Strainer Replace Every 3 mths. or 100 hrs. use

Choke Check With each re-fueling

Ignition System Clean No maintenance

Replace For coil and flywheel

IMPORTANT: Time Intervals shown are maximum. Actual use and your experience will determine thefrequency of required maintenance.

Notes:

* Replacement will be required for commercial use after 600 hours. For Consumer use, cleaning every 6 months is required. Cleaning includes Rebuild Kits.


26/3226

Your MANTIS Tiller has beendesigned and built to accept awide range of MANTIS TillerAttachments to increase itsusefulness in your lawn and

garden. And, all MANTIS TillerAttachments have beendesigned for quick and easyattachment to the Tiller orEngine.

The Border Edger(Item #3222)

The most popularattachment, the Border Edgercan be used to cut clean, neatedges along walkways, oraround trees, shrubs, andgarden beds.

The Border Edger has twoparts: a wheel and a hardenedsteel blade, with pointed tines.

How to Install theBorder Edger

The following instructionsrefer to right and left axles.Assume that youre standingbehind your Tiller, as youwould for tilling andcultivating.

Some areas of your yard mayharbor roots and otherunderground obstructions. Inplaces like this youll want toedge your borders shallowly (1

to 2 deep). Heres how toinstall the Border Edger forshallow edging:

1. First remove yourtilling/cultivating tines.

2. Then slide the edgerswheel onto the right axle.

3. Now slide the Edger bladeonto the left axle. The bladesangled face should hit the

ground when you spin the bladeforward.

4. Insert retaining pins onboth left and right axles.

Around walkways and gardenbeds, youll want to edge moredeeply (3 to 4 deep). Hereshow to install the Border Edgerfor that purpose:

1. Remove the

tilling/cultivating tines.2. Slide the Edgers blade onto

the right axle. The bladespointed face should hit theground when you spin the bladeforward.

3. Slide the wheel onto theleft axle.

4. Insert retaining pins onboth sides.

How to Use theBorder Edger

1. Position your MANTISTiller so that the Edger blade isright along the garden edge andthe wheel is outside (on thelawn, on the sidewalk,wherever). (Picture 1)

2. Start your Tiller and pullyour MANTIS backward along

the garden edge. (Picture 2)

The Border Edger CanHandle SpecialProjects!

1. Install the Edger for deepedging, as directed above. Thenuse it to cut sod strips.

2. Edge and weed at the sametime! Just attach the Edgerblade on one axle and a Tillertine on the other axle, Mix andmatch blades; dont be afraid toexperiment.

IMPORTANT NOTE:If you do a lot of edging,

youll appreciate theMANTIS Wheel Set

(Item#9222.) It gives youadded stability, for eveneasier handling.

To order the wheel Set, orany MANTIS Attachment,contact your local authorizedMANTIS dealer.

USING THE BORDER EDGER ATTACHMENT

Picture 1 Picture 2


27/3227

MANTIS TILLER ASSEMBLY

P/N 438LA

P/N 438RA

DIRECTION

Raised Hub

Teeth point ina Clockwise

Direction

DIRECTION

Raised Hub

Teeth point ina CounterClockwiseDirection

When you look at a Tine with the raised hub facing youand the teeth are pointing in a CLOCKWISE rotation,you have a LEFT HAND TINE.

When you look at Tine with the raised hub facing youand the teeth are pointing in a COUNTER CLOCKWISE

rotation, you and a RIGHT HAND TINE.

55

ITEM NAME QTY MATERIAL

1 400215 1 Throttle Lever

2 400220 1 Grip-Thru

3 400214 1 Grip

4 400226 1 Upper Handle - Tube Left

4A 400236 1 Upper Handle Assembly

Includes Item #s 3 & 4.

5 400225 1 Upper Handle - Tube Right

5A 400235 1 Upper handle Throttle SideAssembly. Includes Item #s

1,2,5,9,10,11,13,16,17,18,19.

6 400224 2 Lower Handle - Fold Down

7 488M 1 Label

8 148 1 Handle Brace

9 464 1 Switch Bracket

10 479 1 Switch

11 1612-70A 1 Switch Cover

13 478 2 Throttle Clip

16 4075 1 Connector Wire

17 400229 2 Cable Retainer


19 467-2 1 Throttle Cable Assy.

20 465 1 Fender Guard

21 400906 1 Engine Assembly SV-5C/1

22 468 1 Drive Shaft

23 466 1 Worm Gear Housing

24 436 1 Gasket

25 437A 1 Housing Cover

26 651 4 Rd. Hd. Self Tapping Screw27 423 1 Roller Bearing

28 425 2 Worm Bearing Race

29 424 1 Worm Thrust Bearing

30 422 1 Worm Shaft

31 426 1 Worm Disk

32 428 1 Retaining Ring

33 429 1 Worm Gear

34 431 1 Tine Shaft

35 430 2 Worm Gear Thrust Washer

36 432 2 Worm Gear Bearing

37 434 2 Bearing Seal


38 435 2 Bearing Seal Retainer

39 438LA 1 Tine Assembly (LT)

40 438RA 1 Tine Assembly (RT)

41 418-1 2 Tine Retaining Hair Pin

42 400218 1 Carrying Handle

43 487MA 1 Engine Label

44 4043 1 Tine Label

45 458 1 Roller Bearing46 4058 1 Mantis Label

47 410 2 Cap Screw 1/4-20 x 1 LG.

48 972 4 Lock Nut 1/4 - 20

49 470 2 1/4 - 20 x 3 Bolt

50 140 2 Bolt 1/4-20 x 3/8 Lg.

51 377 2 Handle Clamp

52 400509 2 Bolt

53 400510 2 Knob

54 400230 2 Plug

55 400010 1 Transmission Assembly

*

* Also in Key #55

*


28/3228

AIRCLEANER, MUFFLER,& THROTTLE

SV-5C/1 ENGINE PARTS ASSEMBLIESCARBURETOR

KEY PART QTY DESCRIPTIONNO. NO.

40 178001-11820 1 Throttle Cable

41 900502-00006 2 Nut, 642 900610-00006 2 Washer, Lock 644 163400-02160 1 Switch, On/Off50 900220-05028 1 Screw, Shoulder 5 x 2551 178110-05330 1 Screw 5 x 2852 900500-00005 1 Locknut 553 900560-00005 1 Nut 554 178024-06130 1 Throttle Bracket55 178010-06460 1 Throttle Trigger56 178043-05230 1 Spring Throttle Return

KEY PART QTY DESCRIPTIONNO NO

1 90052800005 1 Wing Nut

2 13032611522 1 Cover, Air Cleaner3 89012140630 1 Label, Choke4 13031004560 1 Filter, Air5 90024205057 2 Screw 5x576 13041005360 1 Bracket, Air Cleaner7 17851504560 1 Shutter, Choke8 17851600830 1 Spacer9 13030104560 1 Case, Air Cleaner Includes Item 1010 17881005230 1 Grommet11 17851004560 1 Rod, Choke12 12520013124 1 Carburetor -- C1u-k54a13 V103000111 1 Gasket, Intake14 90023805020 2 Screw 5x2015 13001742031 1 Insulator*16 90050000005 2 Nut 517 13001042032 1 Shield, Cylinder


12520013124 1 Carburetor Asy C1u-k54aIncludes Items 1-32

1 12534405360 4 Screw2 P005000620 1 Ring3 12538108660 1 Pump, Purge4 P005000600 1 Base, Purge5 A B 1 Diaphragm, Metering6 A B 1 Gasket, Metering Diaphragm7 ------------------- 1 Body, Carburetor

Not Available Separately8 12533942030 1 Screw9 A 1 Pin, Metering Lever10 A 1 Lever, Metering11 A 1 Spring, Metering Lever12 A 1 Valve, Inlet Needle13 A 1 Plug, Welch14 12537613120 1 Nozzle, Main Check Valve

15 12531649030 1 Valve, Throttle16 12531413930 1 Screw


17 12532715130 1 Clip18 12531342030 1 Spring, Throttle Return

19 12531713310 1 Shaft, Throttle20 12532713930 1 Clip21 12537242030 1 Swivel22 12531813120 1 Needle, Low Speed23 12532909860 1 Cap, Limiter - Low Speed24 12532013310 1 Needle, High Speed25 12532939030 1 Cap, Limiter - High Speed26 A 1 Strainer27 A B 1 Diaphragm, Fuel Pump28 A B 1 Gasket, Fuel Pump29 12532412820 1 Cover, Pump30 12533306960 1 Spring, Adjust Screw31 12533406960 1 Screw, Idle Adjust32 12531012820 2 Screw

A 12530013120 1 Repair Kit

B 12530313120 1 Gasket/Diaphragm Kit


18 V104000590 1 Shield, Muffler*

19 14581011520 1 Muffler20 90060000005 2 Washer 521 90010505050 2 Bolt 5x5022 14586240630 1 Screen, Muffler23 14586642031 1 Gasket, Exhaust*24 A313000610 1 Guide, Exhaust25 90024204010 3 Screw 4x10

*Also Included In Gasket Kit

26 P021007600 1 Gasket Kit


29/3229

SV-5C/1 ENGINE PARTS

STARTER, PAWL CATCHER& CLUTCH

BLOCKFUEL TANK KEY PART QTY DESCRIPTION

NO NO

1 A130000420 1 Cylinder2 90016205022 2 Bolt 5x223 V100000160 1 Gasket, Cylinder*4 P021007610 1 Piston, Kit Includes Items 5-95 A101000090 1 Ring, Piston

6 10001311520 1 Pin, Piston7 10001504630 2 Circlip, Piston Pin8 10001408960 2 Spacer, Piston Pin9 V553000010 1 Bearing, Needle10 A011000350 1 Crankshaft Asy11 10020411521 1 Crankcase Kit Includes Items 12-1612 10021242031 2 Oil Seal13 10021503930 2 Dowel Pin14 10024242030 1 Gasket, Crankcase*15 9403536201 2 Bearing, Ball16 90016205028 3 Bolt 5x28

*Also Included In Gasket Kit

17 P021007600 1 Gasket Kit18 A411000130 1 Coil, Ignition

19 90016204020 2 Bolt 4x2020 15611004920 1 Bushing21 V475002200 1 Tube22 15901201620 1 Cap, Spark Plug23 15901103432 1 Terminal, Spark Plug24 15901019830 1 Spark Plug -- Bpm-8y25 16202152830 1 Lead, Ignition26 61032502730 1 Woodruff Key27 A409000150 1 Flywheel28 90060500008 1 Spring Washer 829 17720212220 1 Starter Pawl Asy Includes Items 30-3130 17721842030 2 Pawl, Starter31 17723412220 2 Spring, Pawl Return32 A160000610 1 Cover, Cylinder33 90023804018 1 Phillips-Head Screw 4x1834 9110704008 1 Hex-Head Screw 4x8


14 17720012820 1 Starter Asy Includes Items 15-2015 17722042030 1 Spring, Rewind16 17721544430 1 Drum, Starter17 17722605530 1 Rope, Starter

Use Bulk Rope 999444440003mm(1/8in) X 1000mm(39-1/2in)

18 17722742030 1 Guide, Rope19 17722811120 1 Starter Grip Kit20 17723644330 1 Screw21 90023804016 4 Screw 4x1622 17500007531 1 Clutch Asy Includes Items 23-2523 17501605020 1 Hub, Clutch24 17501805130 2 Spring, Clutch25 17500905131 2 Shoe, Clutch26 17501904630 1 Plate, Clutch27 90060000010 1 Washer 1028 90080836000 1 Bearing, Ball29 17501004633 1 Drum, Clutch30 17504404630 1 Washer, Clutch31 17501411520 1 Washer, Clutch32 90023806012 1 Screw 6x1233 90023804014 4 Screw 4x1434 90060000005 1 Washer 535 90060500005 1 Spring Washer 536 13041611520 1 Bolt 5x25

Model Sv-5c/137 61022311520 1 Case, Clutch

Model Sv-5h237 A570000050 1 Case, Clutch


1 13100511821 1 Tank, Fuel2 90027505015 3 Screw 5x153 13201011520 1 Pipe, Fuel - 3x5x210mm

Optional Bulk Line 900144 13211546730 1 Grommet

5 13201309820 1 Clip6 13120507320 1 Filter, Fuel7 13130056430 1 Valve, Check8 13011100530 1 Clip, Pipe9 13131239130 1 Pipe, Vent - 3x5x70mm

Optional Bulk Line 9001410 13201049030 1 Pipe, Return - 3x6x50mm

Optional Bulk Line 9001711 13100409060 1 Fuel Tank Cap Asy

Includes Item 12-1312 13101655830 1 Gasket, Fuel Tank Cap13 13105156030 1 Connector, Fuel Tank Cap


30/3230

EPA / CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR RIGHTS AND OBLIGATIONS

The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and the Equipment Manufacturer are pleased to explain theemission control system warranty on your EPA Phase II / C.A.R.B. Tier 2 model year 2000 and later small off road engine (SORE). New small off road enginesmust be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. Echo, Incorporated must warrant the emission control system onyour small off road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off road engine.

Your emission control system may include parts such as the carburetor or fuel injected system, and the ignition system and catalytic converter. Also includedmay be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, the Manufacturer will repair your small off road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE:

The 1995 and later small off road engines are warranted for two years. If any emission-related part on your engine is defective, the part will berepaired or replaced by the Manufacturer.

OWNER'S WARRANTY RESPONSIBILITIES:

-As the small off road engine owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. TheManufacturer recommends that you retain all receipts covering maintenance on your small off road engine, but the Manufacturer cannot deny warrantysolely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

-As the small off road engine owner, you should however be aware that the Manufacturer may deny you warranty coverage if your small off road engine ora part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off road engine to the Manufacturer's authorized service center as soon as a problem exists. The warranty repairsshould be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your Product Manufacturer.

EPA / CALIFORNIA EMISSIONS DEFECT WARRANTY EXPLANATION

This is additional detailed information about the EPA / CALIFORNIA EMISSIONS DEFECT WARRANTY for your small off road engine.

WHAT DOES THIS WARRANTY COVER?

The Manufacturer warrants that your unit was designed, built and equipped to conform with applicable California emissions standards and that your unit is freefrom defects in material and workmanship that would cause it to fail to conform with applicable requirements within two (2) years. The warranty period beginson the date the product is delivered to a retail purchaser. This is your emission control system, DEFECTS WARRANTY.

HOW WILL A COVERED PART BE CORRECTED?

If there is a defect in a part covered by this warranty, a Manufacturer's Authorized Service Dealer will correct the defect.

You will not have to pay anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by thedealer. In addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.

Emissions System repairs covered under this warranty should be completed in a reasonable time, not to exceed 30 days.

IMPORTANT

If the diagnosis reveals no defect, the emission defect warranty does not apply.

WHAT PARTS ARE COVERED BY THE EPA PHASE II AND C.A.R.B. 2000& LATER SMALL OFF ROAD ENGINE EMISSIONS DEFECT WARRANTY?

Any emission related part not scheduled for, "required maintenance" (See Engine Operators Manual, "SERVICE MAINTENANCE SCHEDULE") will berepaired or replaced within the warranty period. The repaired or replaced part will be warranted for the remaining Emissions Defect warranty period.

Any emission related part scheduled for replacement during "required maintenance" (See Engine Operators Manual, "SERVICE MAINTENANCESCHEDULE") is warranted for the period of time prior to the first scheduled replacement point for that part. Any such part repaired or replaced underwarranty shall be warranted for the remainder of the period prior to the first scheduled replacement point for that part.

Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission-related parts, and must beprovided without charge if the part is still under warranty.

Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warrantyobligations of the manufacturer.

The owner is responsible for the performance of the required maintenance described in the operators manual.

SPECIFIC EMISSION RELATED WARRANTED PARTS:

Carburetor (complete assembly or replaceable components) Choke Fuel Injection Assembly or replaceable componentsAir Filter Electronic Ignition System Spark Plug Catalytic Converter / Muffler Assembly

WHAT IS NOT COVERED BY THE EPA / CALIFORNIA EMISSIONS DEFECT WARRANTY?

Any failure caused by abuse, neglect, improper maintenance.

Any failure caused by unapproved modifications, use of unapproved add-on parts/modified parts or unapproved accessories.


31/3231

NOTES


32/32

LIMITED WARRANTY INFORMATION

FOR MANTIS TILLER

MANTIS extends only to the originalconsumer purchaser a limited warrantyagainst defects in material and

workmanship for a period of two yearsfrom date of purchase. This warrantycovers all portions of the MANTIS Tiller.

MANTIS will repair or, at its option,replace any defective part or parts of theproduct free of charge. In the event of adefect or malfunction, the purchaser mustreturn the product to an authorized MANTISdealer.

MANTIS assumes no responsibility in theevent that the product was assembled orused in contravention of any assembly,care, safety, or operating instructionscontained in the Owners Manual; was notused with reasonable care; or was used forother than normal and intended purposes.

MANTIS MAKES NO EXPRESSWARRANTIES OR REPRESENTATIONEXCEPT THOSE CONTAINED HEREIN. THE

DURATION OF ANY IMPLIED WARRANTY,INCLUDING MERCHANTABILITY ANDFITNESS FOR A PARTICULAR PURPOSE, ISLIMITED TO THE DURATION OF THEEXPRESS WARRANTY. MANTIS DISCLAIMSALL LIABILITY FOR INDIRECT AND/ORCONSEQUENTIAL DAMAGES. SOMESTATES DO NOT ALLOW LIMITATIONS ONHOW LONG AN IMPLIED WARRANTYLASTS AND/OR DO NOT ALLOW THE

EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIALDAMAGES, SO THAT ABOVE LIMITATIONSAND EXCLUSIONS MAY NOT APPLY TOYOU. THIS WARRANTY GIVES YOUSPECIFIC LEGAL RIGHTS, AND YOU MAYALSO HAVE OTHER RIGHTS WHICH VARYFROM STATE TO STATE.

MANTIS

1028 Street RoadSouthampton , PA 18966(215) 355-9700

Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.

P/N 401702

MANTIS 09/Printed in USA

Documents

Mantis rototiller