Upload
ayman-yassin
View
36
Download
4
Embed Size (px)
Citation preview
307-01-1 307-01-1Automatic Transaxle/Transmission
DISASSEMBLY AND ASSEMBLY
OF SUBASSEMBLIES
Main Control Valve Body
Special Tool(s)
Aligner, Valve Body (2required)307-334 (T95L-70010-C)
Item Part Number Description Item Part Number Description
8 — Spring — converter clutch1 — Clip — retainercontrol valve2 — Plug — retainer
9 — Valve — converter clutch3 — Valve assembly — thermocontrol
4 — Valve — fluid cooler bypass10 — Plate
5 — Spring — fluid cooler bypass11 — Spring — coast clutch control
6 — Clip — retainer12 — Valve — coast clutch control
7 — Plug — retainer13 — Clip — retainer
(Continued)(Continued)
Copyright 2004, Ford Motor CompanyLast updated: 07/29/2004 2005 Mustang, 12/2004
307-01-2 307-01-2Automatic Transaxle/Transmission
DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES (Continued)
Item Part Number Description Item Part Number Description
14 — Plug — retainer 48 — Clip — retainer
15 — Valve — converter clutch 49 — Plug — retainerback pressure 50 — Spring — converter limit
16 — Spring — converter clutch 51 — Valve — converter limitback pressure
52 — Plate17 — Clip — retainer
53 — Spring — solenoid regulator18 — Plug — retainer valve19 — Valve — VFS2 modulator 54 — Valve — solenoid regulator20 — Spring — VFS2 modulator 55 — Valve — manual
valve56 — Clip — retainer
21 — Clip — retainer57 — Plug — retainer
22 — Plug — retainer58 — Spring — rear servo control
23 — Valve — intermediate servo valverelease
59 — Valve — rear servo control 24 — Spring — intermediate servo
60 — Clip — retainerrelease valve61 — Plug — retainer25 — Plate62 — Spring — RS ISA select26 — Spring — high clutch control
valve27 — Valve — high clutch control
63 — Valve — RS ISA select 28 — Plug — retainer
64 — Clip — retainer29 — Clip — retainer
65 — Plug — retainer30 — Valve — reverse modulator
66 — Spring — forward31 — Spring — reverse modulator engagement control valve
valve67 — Valve — forward engagement
32 — Clip — retainer control33 — Plug — retainer 68 — Plate34 — Valve — reverse engagement 69 — Spring — O.D. servo control35 — Spring — reverse engagement 70 — Valve — O.D. servo control
valve71 — Retainer — clip
36 — Clip — retainer72 — Sleeve — converter clutch
37 — Plug — retainer modulator control38 — Valve — VFS1 modulator 73 — Valve — converter clutch39 — Spring —VFS1 modulator modulator control
valve 74 — Valve — converter clutch40 — Clip — retainer modulator
41 — Sleeve 75 — Spring — converter clutchmodulator control42 — Valve — booster
76 7Z490 Plate assembly — main43 — Valve — boostercontrol valve body separator
44 — Spring — inner77 7E195 Ball — lubrication check
45 — Spring — outer78 7E195 Ball — shuttle valve
46 — Spring — retainer79 7A101 Body — control valve lower
47 — Valve — main regulator80 W701099-S430 Screw — separator plate
(Continued)
2005 Mustang, 12/2004
307-01-3 307-01-3Automatic Transaxle/Transmission
DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES (Continued)
Disassembly 2. CAUTION: Do not stone, file or sandthe valves. This will remove the anodized
1. NOTE: The valve body separator plate has a finish and may result in further main controlbonded gasket. Do not reuse. Discard the plate. or transmission damage.
Remove and discard the valve body separator After cleaning the main control valve body,plate. carry out the following.
• Inspect all valve and plug bores for scoringor burrs.
• Check all fluid passages for obstructions.
• Inspect all valves and plugs for burrs.
• Inspect all mating surfaces for burrs ordistortion.
• Inspect all springs for distortion.
• Check all valves and plugs for freemovement in their respective bores.
X Valves and plugs, when dry, must fallfrom their own weight into theirrespective bores.
2. Remove the check balls.• Roll the manual valve on a flat surface to
check for a bent condition.
3. Assemble the main control valve body.
4. Install the main control valve body check balls.
3. NOTE: Refer to the disassembled view.
Disassemble the main control valve body onlyif cleaning is required.
Assembly
1. CAUTION: Do not lose parts whencleaning or repairing.
Thoroughly clean all parts in solvent and blowdry with moisture-free compressed air.
2005 Mustang, 12/2004
307-01-4 307-01-4Automatic Transaxle/Transmission
DISASSEMBLY AND ASSEMBLY OF SUBASSEMBLIES (Continued)
5. NOTE: Use a new valve body separator platefor main control valve body installation.
Using the special tools, install a new maincontrol valve body separator plate.
• Tighten to 7 Nm (62 lb-in).
2005 Mustang, 12/2004