M36 MRC Wall Washer LED Recessed [L36/L36R1/L36R2] selux

In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.

Selux Corporation © 2021, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us

Project:

Type: Qty:

Date: Customer:

Page 1 of 11 (Rev. 12/2021)

L36WWR_SS_v2.8

M36 MRC Wall WasherLED Recessed

Order Code:

Emergency Options

EC8 Emergency Wing Circuit

FS In-Line Fuse

Fixture Options

Sensor Options

xE

Enlighted(consult factory)

xS1 Sensor Switch Daylight (consult factory)

xS2 Sensor Switch Occ/Vac(consult factory)

xS3 Sensor Switch Occ/Vac/Daylight(consult factory)

Replace “x” with quantity

xSN nLight Enabled (consult factory)

EMR Remote Micro Inverter (consult factory)

EM8 Integral EM Battery Pack (non-IC Rated)

xV Lutron Vive (consult factory)

Driver

CCEA CCEA (Chicago Plenum) Approved

Configuration Options

IL9 Unlit Horizontal 90° Inside Corner (consult factory)

OL99,10 Unlit Horizontal 90° Outside Corner

DIL5,6 eldoLED 1% ECOdrive 0-10V (Logarithmic)

DIM5 0-10V, 1% (Linear)

DED5,6 eldoLED 1% ECOdrive DALI-2 (Logarithmic)

D015,6 eldoLED 0.1% SOLOdrive 0-10V (Linear)

DL015,6 eldoLED 0.1% SOLOdrive 0-10V (Logarithmic)

DC25,6,7 Lutron 1% 2-Wire

DE15,6 Lutron 1%EcoSystem

5 See page 7 for details6 Available starting 2’ and up7 120V only

L36 WW- - - - - - - - -- - -

9 See page 9 for details and restrictions.

10 Unlit corner uses blank faceplate, standard length is 36” long nominal. For other configurations, please consult factory.

BUY AMERICAN

DC3 Lutron 1% 3-Wire (consult factory)

8 See page 8 for details.

LED WARRANTY

5YEAR

ARRA Compliant

ADA Compliant

Series L36 M36 LED Direct

DirectLight Engine

Shielding WW M36 MRC Wall Wash Optic

Nominal Fixture Length

01 1 ft.

02 2 ft.

04 4 ft.

03 3 ft.

05 5 ft.

06 6 ft.

08 8 ft.

07 7 ft.

XX Runs (over 12’) & Configurations, round up to the nearest foot and replace the “xx” with the # (i.e. 13=13’ nominal)

Housing Finish

WH White

SV Silver

SP Specify Premium Color

L36

CCT 930 3000K 90+ CRI

935 3500K90+ CRI

940 4000K 90+ CRI

927 2700K 90+ CRI

09 9 ft.

11 11 ft.

10 10 ft.

12 12 ft.

BL Semi-Matte Black

L36R1 Continuous Flange Flanged Endcap

L36R2 Non-continuous Flangeless Endcaps

Voltage

A451,2 724lm/9.2W per foot

A351 563lm/7.2W per foot



1 Values calculated from a 4’ fixture at 3500K, 90+ CRI, and DIM driver.

2 Not available with Lutron

1120V

2277V

U 120V through 277V 50/60hz capable

3347V (consult factory)

WW

MountingL36

SG Slot Grid (9/16”) (Wire Suspension or 1/4”-20 stud)

SF1 Spackle Flange (1/2” Drywall)

SF2 Spackle Flange (5/8” Drywall)

SF3 Spackle Flange (After Drywall)

DC Decoustic Ceiling (up to 2” thick)

TBS3 T-Bar Length with 1” 1/4”-20 Stud

RC4 Rotating Crossbar (Ceilings 1/4” to 2” thick )

TS 1” 1/4”-20 Stud

TB3 T-Bar Length with suspension clips

MountingL36R1 or L36R2

3 L36R1 only 4 Consult factory for lengths under 2’

or

* Custom colors are available, Please consult factory. Optic cover painted to match housing finish. For Semi-Matte Black optic cover, please consult factory.


Selux Corporation © 2020, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Page 2 of 11(Rev. 12/2021)

L36WWR_SS_v2.8


Construction:

Housing - Continuous, low copper 6063-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 12’) or Runs.

Geartray - Low copper 6063-T6 extruded aluminum profile.

Optics- Injection molded Polycarbonate lens and aluminum vacuum metalized reflector.

Mounting(s) - Spackle in (drywall), Slot Grid, Decoustic, T-bar Grid, Perimeter, Rotating Crossbar and Threaded Stud Mountings (see pages 3 through 6 for details).

Standard Luminaire lengths - All standard luminaires are supplied in nominal lengths to ensure full, even, illumination. Runs and Configurations are available in approximately 6” increments starting at the nominal 1’ fixture length with integral drivers (without EM).** Individual luminaires are not joinable in the field.

Exact length luminaires - Individual luminaires, Runs, and Configuration are available in exact lengths to meet your project needs. Run will comprise of 6” optic lengths that will fill length of Run, and identical blank optic covers at either end of fixture to fill in non-illuminated length. If any other configuration or run is required, please consult factory.

M36 Joiner(s) - Runs and Configurations are supplied in multiple housings that are joined together in the field using the supplied M36 Joiner System. This allows ease of installation and ensures a uniform appearance (see page 8 for detail).

Weight - 2.0 lb. per foot

Electrical/Performance:

LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine with a reported luminous flux maintenance at 50,000 hours is 89% based on LM-80 test reports. The rated lumen maintenance life of L80 (10K) > 60,000 hours. Luminous flux values calculated in accordance to IES TM-21 procedures based on ANSI/IES LM-80 compliant reported measurement data. For Title 24 compliant model numbers, please consult factory.

Photometrics - Consult website or factory for IES Files. Photometric lumen measurement complies with IES LM-79-08 testing procedures. Due to the LED manufacturer’s tolerances, the listed output has a ±5% tolerance. For outputs based on different optics or CCT, please see page 10 for details.

CCT - Available in 2700K, 3000K, 3500K and 4000K, tolerance within a 3-step MacAdam ellipse.

CRI - 90+.

All Drivers - High efficiency, constant current, soft start, Electronic Class 2 with a PFC > 0.90. Consult factory for details and specifications.

Sensors - Selux offers a variety of integral sensor options. Consult factory for details and specifications.

Emergency - There are multiple emergency options available - emergency circuit, remote micro inverter, and integral battery pack. Please consult factory for use of sensors with emergency options. For more details on EC and EM options, see page 8.

Thermal Performance:

Ambient Operating Temperature - Luminaires suitable for maximum ambient temperature of 35°C (95°F) for all drivers. Luminaires are suitable for minimum ambient temperatures of -40ºC (-40ºF) for DIM, DIL, DED, D01 and DL01 drivers; 0ºC (32ºF) for DC2 and DE1 drivers.

Luminaire Finish:

Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI.

All products undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention.

Standard interior colors are White (WH), Semi-Matte Black (BL), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide.

Warranty:

5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the M36 series LED luminaire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see “Selux Terms and Condition of Sale.”

Certifications and Compliance: NRTL - For Dry and Damp location (I.E. cULus; cCSAus) ARRA Compliant RoHS CompliantIC Rated (EM option is non-IC Rated)

L36 L36R1/2

21316

"(7

2mm

)

1 716 "

(37mm)

1 516 "

(34mm)

21316

" (

72m

m)

2 716 "

(62mm)

1 516 "

(34mm)

1 1316 "

(46mm)

3 16"

(5m

m)

3 16"

(5m

m)

1 15/16” (46mm)

2 13/16” (72mm)

2 7/16” (62mm)

3/16”

(5

mm

) 1 5/16” (34mm) 3/

16”

(5m

m)

2 13/16” (72mm)

1 5/16” (34mm)

1 7/16” (37mm)

Page 3 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



Blocking(By Others)

Blocking(By Others)

Spackle Flange (SF1) (1/2" drywall)

Spackle Flange (SF2) (5/8" drywall)

Spackle Flange (SF3) (After drywal installation)

Fixtures must be installed

before drywall.

Fixtures must be installed

before drywall.

1 1/2"(Ref.)

1 1/2"(Ref.)

1 9/16"(Ref.)

1 1/

2"

(Ref

.)

1. 1/4-20 Threaded rod to structure (supplied and installed by others).2. 1/4-20 Coupler hardware (supplied and installed by others).3. 1" 1/4-20 Stud (by selux)4. Ă5/16" [Ă7mm] mounting hole.5. Drywall/Sheetrock screw (Ref.)6. Drywall/Sheetrock (Ref.)7. 1/16" Plaster skimcoat (Ref.)8. Drywall/Sheetrock tape (Ref.)9. Blocking to secure fixture (by others)10. Electrical connection box, removable side cover for electrical connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.11. Brackets installed and shipped in the closed position by selux. - For runs, rotate bracket to open position so the geartray can be removed to make the housing and wiring connections. - After connections are made rotate bracket back to the closed position (see installation instruction for full details). - Brackets to be removed only after the luminaire is completely secured to the sheetrock through the spackle flange.

412

56

87

3

412

56

87

3

59

11

11

11

10

876

1. 1/4”-20 Threaded rod to structure (supplied and installed by others).2. 1/4”-20 Coupler hardware (supplied and installed by others).3. 1” 1/4”-20 Stud (by Selux).4. Ø5/16” (Ø7mm) mounting hole. 5. Drywall/Drywall screw (Ref.)6. Drywall/Drywall (Ref.)7. 1/6” Plaster skimcoat (Ref.)8. Drywall/Drywall tape (Ref.) 9. Blocking to secure fixture (by others) 10. Electrical connection box, removable side cover for electrical

connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.

11. Brackets installed and shipped in the closed position by Selux. - For Runs, rotate bracket to open position so the geartray can be removed to make the housing and wiring connections.

- After connections are made, rotate bracket back to the closed position (see installation instructions for full details).

- Brackets to be removed only after the luminaire is completely secured to the drywall through the spackle flange.


1 1 /2

” (R

ef.)

1 9/16” (Ref.)

1 1/2” (Ref.)

1 1/2” (Ref.)

1/2” Spackle Flange Mounting (SF1)

Installation brackets

5/8” Spackle Flange Mounting (SF2)


Blocking (By Others)

Blocking (By Others)

After Drywall Flange Mounting (SF3)

Spackle Flange Mounting (SF1, SF2 and SF3) - Dimensions

Nominal Length

“A” O.A.L. w/o Flange

“B” End Suspensions

* “C” (Ref.) Mid. Suspension

“D” Feed Location

Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM

01 (1 ft.) 1' - 1/2" 317 0' - 1 5/8" 41 0' - 9 1/4" 235 0' - 4 1/8" 105

02 (2 ft.) 2' - 1/2" 622 0' - 1 5/8" 41 1' - 9 1/4" 539 0' - 4 1/8" 105

03 (3 ft.) 3' - 1/2" 927 0' - 6 1/8" 156 2' - 1/4" 616 0' - 2 1/8" 54

04 (4 ft.) 4' - 1/2" 1232 0' - 6 1/8" 156 3' - 1/4" 920 0' - 2 1/8" 54

05 (5 ft.) 5' - 1/2" 1536 0' - 6 1/8" 156 4' - 1/4" 1225 0' - 2 1/8" 54

06 (6 ft.) 6' - 1/2" 1841 0' - 6 1/8" 156 5' - 1/4" 1530 0' - 2 1/8" 54

07 (7 ft.) 7' - 1/2" 2146 0' - 6 1/8" 156 6' - 1/4" 1835 0' - 2 1/8" 54

08 (8 ft.) 8' - 1/2" 2451 0' - 6 1/8" 156 7' - 1/4" 2140 0' - 2 1/8" 54

09 (9 ft.) 9' - 1/2" 2756 0' - 6 1/8" 156 8' - 1/4" 2444 0' - 2 1/8" 54

10 (10ft.) 10' - 1/2" 3060 0' - 6 1/8" 156 9' - 1/4" 2750 0' - 2 1/8" 54

11 (11ft.) 11' - 1/2" 3365 0' - 6 1/8" 156 10' - 1/4" 3054 0' - 2 1/8" 54

12 (12ft.) 12' - 1/2" 3670 0' - 6 1/8" 156 11' - 1/4" 3359 0' - 2 1/8" 54

*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.

Spackle Flange (SF1)(1/2” Drywall)

Spackle Flange (SF2)(5/8” Drywall)

Spackle Flange (SF3)(After Drywall Installation)

Fixtures mustbe installed

before drywall

Fixtures mustbe installed

before drywall

Top View

SideView

BottomView

Top View

SideView

BottomView

Top View

SideView

BottomView


Page 4 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



1. 9/16” Slot grid (shown as ref.) 2. Support wire to structure

(supplied and installed by others).3. 1/4”-20 Threaded rod to structure

(supplied and installed by others).4. 1/4”-20 Coupler hardware

(supplied and installed by others).5. 1” 1/4”-20 Stud (by Selux).6. Ø5/16” (Ø7mm) mounting hole.


Slot Grid Mounting (SG)

2" Ref.

2

1

634

5

9/16” Slot Grid Mounting (SG) (Wire Suspension or 1/4”-20 Stud)

*Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.

Slot Grid Mounting (SG) - Dimensions

Nominal Length

“A” Housing Length


* “C” (Ref.) Mid. Suspension


“E” Grid Spacing

Illuminated Length

Blank Infill Lengths

Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet Feet/Inch

MM Feet/Inch MM

02 (2ft.) 1' - 11 7/16" 595 0' - 1 5/8" 41 1' - 8 3/16" 513 0' - 4 1/8" 105 2' Center to Center 1' - 6" 457 0' - 2 1/2" 63



06 (6ft) 5' - 11 7/16" 1815 0' - 6 1/8" 156 4' - 11 3/16" 1503 0' - 2 1/8" 54 6' Center to Center 5' - 6" 1676 0' - 2 1/2" 63


1. 1/4”-20 Threaded rod to structure (supplied and installed by others).2. 1/4”-20 Coupler hardware (supplied and installed by others).3. 1” 1/4”-20 Stud (by Selux).4. Ø5/16” (Ø7mm) mounting hole.5. 1” wide alum. angle runs the entire length of fixture to block view into plenum

area from below fixture.6. Suitable for Decoustic® ceiling panel installations with panels up to 2” thick

(supplied and installed by others). Other ceiling systems possible, please consult factory. Decoustic® is a registered trademark of Decoustics Ltd. Corporation.

Decoustic Mounting (DC)

2" (REF.)CEILINGPANEL

1" (25mm)

2 1/

4"(5

7mm

)

4

123

56

Decoustic Mounting (DC) (Panels up to 2” thick)

Decoustic Mounting (DC) - Dimensions

Nominal Length

“A” Housing Length


* “C1” (Ref.) Mid. Suspension


Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM

01 (1 ft.) 1' - 1/2" 317 0' - 1 5/8" 41 0' - 9 1/4" 235 0' - 4 1/8" 105

02 (2 ft.) 2' - 1/2" 622 0' - 1 5/8" 41 1' - 9 1/4" 539 0' - 4 1/8" 105

03 (3 ft.) 3' - 1/2" 927 0' - 6 1/8" 156 2' - 1/4" 616 0' - 2 1/8" 54

04 (4 ft.) 4' - 1/2" 1232 0' - 6 1/8" 156 3' - 1/4" 920 0' - 2 1/8" 54

05 (5 ft.) 5' - 1/2" 1536 0' - 6 1/8" 156 4' - 1/4" 1225 0' - 2 1/8" 54

06 (6 ft.) 6' - 1/2" 1841 0' - 6 1/8" 156 5' - 1/4" 1530 0' - 2 1/8" 54

07 (7 ft.) 7' - 1/2" 2146 0' - 6 1/8" 156 6' - 1/4" 1835 0' - 2 1/8" 54

08 (8 ft.) 8' - 1/2" 2451 0' - 6 1/8" 156 7' - 1/4" 2140 0' - 2 1/8" 54

*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.

Side View

Bottom View

Top View

Side View

Bottom View

Top View

2 ” (Ref.)

1 ” (25mm)

2 1/4

” (

57m

m)

Page 5 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



T-Bar with Suspension Clips (TB) (9/16” or 15/16” grid)

T-Bar with 1/4”-20 Stud (TBS) (9/16” or 15/16” grid)


T-Bar Mounting (TB) T-Bar with Stud Mounting (TBS)

Side View

Bottom View

Top View

Side View

Bottom View

Top View

745

6

1

2

3 3a

2 9/16” Ref 2 9/16” Ref

1. Support wire to structure (supplied and installed by others).2. Spring steel suspension clips located approximately every 4 ft.

(supplied by Selux).3. 9/16” T-bar grid (shown as ref.)3a. 15/16” T-bar grid (shown as ref.)4. 1/4”-20 Threaded rod to structure (supplied and installed by others).5. 1/4”-20 Coupler hardware (supplied and installed by others).6. 1” 1/4”-20 Stud (by Selux). 7. Ø5/16” (Ø7mm) mounting hole.

**Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.

T-Bar (TB and TBS) Dimensions

Nominal Length

“A” O.A.L. with Flange

“A1” O.A.L. without

Flange


“BB” (TB mtg.) Suspen-

sion Clips

** “C” (Ref.) Mid. Suspension


“E” Grid Spacing

“F” Wall Angle

Blank Infill Lengths

Feet/Inch MM Feet/Inch MM Feet/Inch MM Quantity Feet/Inch

MM Feet/Inch MM Feet Feet/Inch

MM Feet/Inch MM

*02 (2ft.) 1' - 11 13/16" 605 1' - 10 15/16" 583 0’ - 4 1/2" 114 4x 1' - 2" 355 0' - 1 1/8" 29 2' Center to Center 1' - 6" 457 0' - 2 1/3" 60

*04 (4ft.) 3' - 11 13/16" 1215 3' - 10 15/16" 1193 0' - 6 1/8" 156 6x 2' - 10 2/3" 881 0' - 2 1/8" 54 4' Center to Center 3' - 6" 1067 0' - 2 1/3" 60

*05 (5ft.) 4' - 11 13/16 1519 4' - 10 15/16" 1497 0' - 6 1/8" 156 6x 3' - 10 2/3" 1185 0' - 2 1/8" 54 5' Center to Center 4' - 6" 1372 0' - 2 1/3" 60

*06 (6ft) 5' - 11 7/8" 1825 5' - 11" 1803 0' - 6 1/8" 156 6x 4' - 10 2/3" 1491 0' - 2 1/8" 54 6' Center to Center 5' - 6" 1676 0' - 2 1/3" 60

*08 (8ft.) 7' - 11 13/16” 2434 7' - 10 15/16" 2412 0' - 6 1/8" 156 8x 6' - 10 2/3" 2100 0' - 2 1/8" 54 8' Center to Center 7' - 6" 2286 0' - 2 1/3" 60

*For other lengths consult factory

Page 6 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



523

4

1

Rotating Crossbars (RC) (1/4” to 2” thick ceiling)

1/4”-20 Threaded Stud (TS) (1” Threaded Stud)

6 1/2” max. (Ref.)


Rotating Crossbar Mounting (RC) 1/4”-20 Threaded Stud Mounting (TS)

Side View

Bottom View

Top View

Side View

Bottom View

Top View

5 1/2

” m

ax.

(R

ef.)

1. Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling thickness of 1/4” to 2”.

2. 1/4”-20 Threaded rod to structure (supplied and installed by others).3. 1/4”-20 Coupler hardware (supplied and installed by others).4. 1” 1/4”-20 Stud (by Selux).5. Ø5/16” (Ø7mm) mounting hole.

**Dimension(s) rounded to the nearest 1/16” with a ± 1/16” (1mm) tolerance.

Rotating Crossbar (RC) and Threaded Stud (TS) - Dimensions

Nominal Length

“A” O.A.L. with Flange

“A1” O.A.L. without Flange


** “C” (Ref.) Mid. Suspension


Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM

*01 (1 ft.) 1' - 1 3/8" 339 1' - 1/2" 317 0' - 1 5/8" 41 0' - 9 1/4" 235 0' - 4 1/8" 105

02 (2 ft.) 2' - 1 3/8" 644 2' - 1/2" 622 0' - 4 1/2" 114 1' - 3 1/2" 394 0' - 1 1/8" 29

03 (3 ft.) 3' - 1 3/8" 949 3' - 1/2" 927 0' - 6 1/8" 156 2' - 3/16" 615 0' - 2 1/8" 54

04 (4 ft.) 4' - 1 3/8" 1254 4' - 1/2" 1232 0' - 6 1/8" 156 3' - 3/16" 920 0' - 2 1/8" 54

05 (5 ft.) 5' - 1 3/8" 1558 5' - 1/2" 1536 0' - 6 1/8" 156 4' - 3/16" 1224 0' - 2 1/8" 54

06 (6 ft.) 6' - 1 3/8" 1863 6' - 1/2" 1841 0' - 6 1/8" 156 5' - 3/16" 1529 0' - 2 1/8" 54

07 (7 ft.) 7' - 1 3/8" 2168 7' - 1/2" 2146 0' - 6 1/8" 156 6' - 3/16" 1834 0' - 2 1/8" 54

08 (8 ft.) 8' - 1 3/8" 2473 8' - 1/2" 2451 0' - 6 1/8" 156 7' - 3/16" 2139 0' - 2 1/8" 54

09 (9 ft.) 9' - 1 3/8" 2778 9' - 1/2" 2756 0' - 6 1/8" 156 8' - 3/16" 2444 0' - 2 1/8" 54

10 (10 ft.) 10' - 1 3/8" 3082 10' - 1/2" 3060 0' - 6 1/8" 156 9' - 3/16" 2748 0' - 2 1/8" 54

11 (11 ft.) 11' - 1 3/8" 3387 11' - 1/2" 3365 0' - 6 1/8" 156 10' - 3/16" 3053 0' - 2 1/8" 54

12 (12 ft.) 12' - 1 3/8" 3692 12' - 1/2" 3670 0' - 6 1/8" 156 11' - 3/16" 3358 0' - 2 1/8" 54

*RC mounting, consult factory for lengths under 2’


Selux Corporation © 2020, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Page 7 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8


Drivers:

0-10V linear dimming (DIM)Luminaires supplied with drivers offering the capability of either normal switched operation of 0-10V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%. (Due to size constraints, 1’ luminaires are supplied with a driver from a different manufacturer than 2’ and above luminaires. For details, please consult factory).

0-10V logarithmic eldoLED ECOdrive dimming (DIL)Luminaires supplied with drivers offering the capability of either normal switched operation or 0-10V dimming for logarithmic dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%.

eldoLED ECOdrive DALI-2 dimming (DED)Luminaires supplied with ECOdrive DALI-2 dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.

eldoLED SOLOdrive 0-10V linear dimming (D01)Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dimming curve. Minimum dimming level preset at factory to 0.1% and “dim to dark”.

eldoLED SOLOdrive 0-10V logarithmic dimming (DL01)Luminaires supplied with SOLOdrive DA0-10V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 0.1% and “dim to dark”.

LUTRON 2-wire dimming (DC2)Luminaires supplied with Hi-Lume 2-wire dimming driver (120V only) programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.

LUTRON EcoSystem dimming (DE1)Luminaires supplied with Hi-Lume EcoSystem (4 wire, digital link) dimming driver programmed for Constant Current Reduction (CCR). Minimum dimming level down to 1% with SoftOn/FadeToBlack.

*For control recommendations please contact driver manufacturer

Wiring Diagrams

Driver Quantity

1 ft. 2 ft. 3 ft. 4 ft. 5 ft. 6 ft. 7 ft. 8 ft. 9 ft. 10 ft. 11 ft. 12 ft. RUN

DIM,DIL 1 1 1 1 1 1 1 1 1 2 2 2 Consult factory

DED, D01, and DL01 drivers N/A 1 1 1 1 1 1 1 1 1 1 1 Consult factory

DC2 and DE1 drivers N/A 1 1 1 1 1 1 1 1 2 2 2 Consult factory

*For inrush and control current, please refer to the driver manufacturers’ spec sheets.

- The following wire(s) are in addition to the standard above -

DE1

0-10V linear (DIM)0-10V logarithmic eldoLED ECOdrive (DIL) DALI-2 logarithmic eldoLED ECOdrive (DED) 0-10V linear eldoLED SOLOdrive (D01)0-10V logarithmic eldoLED SOLOdrive (DL01)

DIM, DIL, DED, D01, DL01

Lutron EcoSystem (DE1)

Lutron 2-Wire (DC2)

DC2

Standard Wiring supplied for all drivers

Green = GroundWhite = Neutral (120V/277V/347V) or L2 (240V)Black = Hot /L1 (120V-347V)

Pink = (-) DALI-2 or 0-10V Dimming ControlPurple = (+) DALI-2 or 0-10V Dimming Control

Violet = “E1” Digital Link Dimming ControlViolet/White = “E2” Digital Link Dimming Control

No additional wires

Driver

Driver

Driver

FeedGreen White Black

Pink (-)Purple(+)

Green White Black

FeedGreen White Black Violet

Violet/White

Feed

Page 8 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



Fuse (FS) - Luminaires supplied with an in-line fuse located on the hot wire for each feed. (Supplied with an 8A slow burn fuse).

Damp Location (DL) - Luminaires are suitable for use in damp location(s). Examples of such locations include protected areas under canopies, marquees, roofed porches, and similar locations where the fixture(s) are protected from direct contact with rain, snow, or excessive moisture (such as ocean spray). Interior locations include areas subject to moderate degrees of moisture, such as basements and certain barns and cold storage buildings.

90° Elbow on top of the housing (⅞" feed hole)

⅜" flexible metal conduit (6' long)

6" leads

Straight fitting

Flex Whip - Standard for recessed fixtures Joiner System - Standard for Runs and Configurations

Fixture extrusion

Joiner extrusion

Recommended #2 Phillips drive

Fixture extrusion

Additional view


Emergency Wiring (EC) - EC luminaires are intended to be wired to separate panels/breakers for emergency use. See install instructions for proper wiring.

For 1’ to 6’ nominal luminaires, the entire fixture is wired for operation on emergency circuit.

For 7’ and up nominal luminaires, the first 4’ nominal length is wired for operation by a separate EM circuit by default to meet the required “Life Safety Code” (NFPA 101).

If a different configuration is needed, please consult factory.

Note: Wiring may vary slightly due to on-site conditions or local codes. Please follow all safety installation protocols contained within install instructions when installing luminaire.

Emergency Battery (EM) – The EM battery is located integral to fixture and is factory pre-wired. See install instructions for proper wiring.

10W constant power Emergency Battery Pack

For individual fixtures, emergency option will illuminate the first 4’ section of fixture. For continuous runs, please consult factory to advise on 4’ section intended for emergency use. For fixtures >12’ or if a different configuration is needed, please consult factory.

Emergency test switch and plate is a non-illuminated 3” blank section located adjacent to the length of fixture wired for emergency.

Emergency battery is suitable for a minimum temperature of 32°F. For lower temperatures, please consult factory.

*Emergency battery option is UNV for use with 120V or 277V and is not available for 347V.

*Please note battery pack requires an unswitched hot.

*If a different configuration is needed, please consult factory.

Note: Wiring may vary slightly due to on-site conditions or local codes. Please follow all safety installation protocols contained within install instructions when installing luminaire.

Page 9 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8



Listed below are the minimum lengths and details for unlit horizontal 90º outsde corners. These standard corners can be combined with each other and/or the standard luminaire lengths, ensuring full even illumi-nation. If you have any questions, please consult the factory.

The minimum standard lengths for “L” shapes:- OL9 is 4’ x 4’ nominal (example: leg, 90, leg)- Unlit corners are achieved with a blank faceplate that maintains the shape and contour of the optic civer for consistent visual appearance.- Standard unlit corner lengths are 36” to match with optimal wall washer distance from wall. If another length is desired, please consult factory. - For inside corners, please consult factory.

Standard Direct shapes/configurations:

Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.

Project Specific Direct shapes/configurations:


"A" Housing

Wall

Wall

Unlit 90° Outside Corner

Illuminated Section

"A" Housing

Wall

Wall

Blank Faceplate

Illu

min

ate

d S

ecti

on

Unlit Corner and Section - Dimensions

OL9(Outside - unlit)

Feet/Inch MM

“A” Housing (Outside) 3' - 1" 939

“A1” Housing (Inside) 2' - 11 1/2" 902

Indirect Side Top View

Direct SideBottom View

“A” Housing

“A”

Ho

usi

ng

Dir

ect

illu

m (

1’)

“A1” Housing

Direct illum (1’)

Ind

irec

t ill

um

(2’

9”)

Rec

om

men

ded

sp

aci

ng

18

”-24

”

Recommended spacing 18”-24”

Page 10 of 10 (Rev. 12/2021)

L36WWR_SS_v2.8




WW - M36 MRC Wall Wash optic

Light Engine Lumens per 4 foot Lumens per foot Input watts per foot lm/W

A35 2246 562 7.2 78

M36 MRC Wall Washer Recessed

CCT Multiplier

4000K 1.02

3500K 1.00

3000K 0.97

2700K 0.93

CCT multipliers apply to the photometry, IES files, and per foot values listed on page 1 (light engine).

Documents

M36 MRC Wall Washer LED Recessed [L36/L36R1/L36R2] selux