Lucent Technologies KS-22002, Issue 24 December 1, …etler.com/docs/KS/KS-22002.pdf · Lucent Technologies KS-22002, Issue 24 Sheet 3 of 109 December 1, 1998 SHEET INDEX NUMBERS

Lucent Technologies KS-22002, Issue 24 Sheet A

December 1, 1998

KS-22002

LABEL(Common Language Equipment Identification [CLEI]*)

SPECIFICATION

THIS SPECIFICATION AND ALL THE DRAWINGS AND TECHNICAL INFORMATION REFERRED TO ORCONTAINED HEREIN ARE LUCENT TECHNOLOGIES PROPERTY.EXCEPT INSOFAR AS THEY MAY COVER A SUPPLIER'S STANDARD PRODUCT, THEY SHALL BE KEPTIN CONFIDENCE AND RETURNED UPON REQUEST TO THE LUCENT TECHNOLOGIES COMPANYWHICH SUPPLIED THEM. THEY SHALL BE USED ONLY FOR PREPARING QUOTATIONS FORSUBMISSION TO, OR FOR THE MANUFACTURE OF ARTICLES ORDERED BY AN LUCENTTECHNOLOGIES COMPANY. USE FOR OTHER PURPOSES SHALL BE IN ACCORDANCE WITH TERMSAGREED UPON IN WRITING WITH LUCENT TECHNOLOGIES.

THE PRODUCT SHALL BE IN ACCORDANCE WITH THE LATEST INFORMATION AUTHORIZEDHEREIN.

THE QUALITY OF THE MATERIAL USED AND THE METHOD OF MANUFACTURING, HANDLING, ANDSHIPPING, SHALL BE SUCH AS TO INSURE FOR THE FINISHED PRODUCT THE PROPERTIESHEREINAFTER SPECIFIED.

NO DEVIATIONS FROM THIS SPECIFICATION NOR ANY CHANGES IN THE PRODUCT PREVIOUSLYFURNISHED UNDER THIS SPECIFICATION AND FOUND ACCEPTABLE SHALL BE MADE WITHOUTPRIOR APPROVAL.

WHERE DIMENSIONS ARE GIVEN IN THIS SPECIFICATION WITHOUT SPECIFIC TOLERANCES, ORWHERE NO DIMENSIONS ARE GIVEN, THE TOLERANCES AND DIMENSIONS SHOWN ON THEMANUFACTURER'S DRAWINGS, OR PERMITTED BY GOOD SHOP PRACTICES, SHALL BECONSIDERED ACCEPTABLE.

WHEN SAMPLES IN ACCORDANCE WITH THIS SPECIFICATION ARE ORDERED FOR EXAMINATIONAND APPROVAL, NO COMMITMENTS WHICH OBLIGATE THE PURCHASER SHALL BE MADE AND NOMERCHANDISE SHALL BE FURNISHED BY THE SUPPLIER UNTIL SUCH APPROVAL IS RECEIVED,UNLESS THE SUPPLIER IS SPECIFICALLY AUTHORIZED TO THE CONTRARY. THE APPROVAL OFSUCH SAMPLES SHALL NOT BE CONSTRUED AS WAIVING THE REQUIREMENTS OF THISSPECIFICATION IN ANY RESPECT.

ANY PRODUCTION TESTING FACILITIES AND PERSONNEL REQUIRED BY LUCENT TECHNOLOGIESQUALITY REPRESENTATIVE AT THE MANUFACTURER'S PLANT TO DETERMINE THAT THEPRODUCT MEETS THE REQUIREMENTS OF THIS SPECIFICATION SHALL BE PROVIDED BY THEMANUFACTURER.

*COMMON LANGUAGE is a registered trademark and CLEI, CLLI, CLFI, and CLCI are trademarks of Bell Communications Research, Inc.

KS-22002, Issue 24 Lucent TechnologiesSheet 2 of 109October 30, 1998

Lucent Technologies KS-22002, Issue 24Sheet 3 of 109

December 1, 1998

SHEET INDEX

NUMBERS TITLES

KS-22002,Sh A Statement of conditions Sh 2 Sheet Index Sh 3 " " Sh 4 Specification Sh 5 Table of Contents Sh 6 Specification Sh 7 " Sh 8 " Sh 9 " Sh 10 "

Sh 11 " Sh 12 " Sh 13 " Sh 14 " Sh 15 " Sh 16 " Sh 17 " Sh 18 " Sh 19 " Sh 20 " Sh 21 " Sh 22 " Sh 23 " Sh 24 “ Sh 25 “ Sh 26 Figure 1, Lists 1, 2, 6, 18 and 45 Bar Code Labels Sh 27 Figure 2, Code 11, Bar Code Symbol Area Printing Sh 28 Figure 3, Lists 4, 8, 19, 31, 32 and 33 Bar Code Labels Sh 29 Figure 4, Lists 5, 9, 20, 34, 35, 36 and 54 Bar Code Labels Sh 30 Figure 5, Lists 6, 8, 9, 32 and 35 Tabs Layout Sheet Sh 31 Figure 6, List 11 Code Label Sh 32 Figure 7, Lists 12 and 37 Bar Code Labels Sh 33 Figure 8, Lists 13 and 38 Bar Code Labels Sh 34 Figure 9, Lists 14 and 39 Bar Code Labels Sh 35 Figure 10, Lists 15 and 40 Bar Code Labels Sh 36 Figure 11, List 16 Bar Code Label Sh 37 Figure 12, List 17 Bar Code Label Sh 38 Figure 13, Lists 21 and 41 Bar Code Labels Sh 39 Figure 14, List 22 Bar Code Label Sh 40 Figure 15, List 23 Bar Code Label Sh 41 Figure 16, List 24 Bar Code Label Sh 42 Figure 17, Lists 25, 42 and 62 Bar Code Labels Sh 43 Figure 18, List 26 Bar Code Label Sh 44 Figure 19, List 27 Bar Code Label Sh 45 Figure 20, Lists 28, 29, 30 and 44 Bar Code Labels / Area Printing Sh 46 Figure 21, Code 39, Bar Code Symbol Area Printing Sh 47 Figure 22, List 43 Bar Code Label Sh 48 Figure 23, Lists 46 and 70 Bar Code Labels Sh 49 Figure 24, Lists 47 and 57 Bar Code Labels

KS-22002, Issue 24 Lucent TechnologiesSheet 4 of 109December 1, 1998

SHEET INDEX (continued)NUMBERS TITLES

Sh 50 Figure 25, Lists 48 and 58 Bar Code Labels Sh 51 Figure 26, Lists 49 and 50 Bar Code Labels

Sh 52 Figure 27, Lists 51 and 52 Bar Code Labels Sh 53 Figure 28, List 53 Bar Code Label Sh 54 Figure 29, List 55 Bar Code Label Sh 55 Figure 30, List 56 Bar Code Label Sh 56 Figure 31, Lists 59 and 60 Bar Code Labels Sh 57 Figure 32, List 61 Bar Code Label Sh 58 Figure 33, List 63 Bar Code Label Sh 59 Figure 34, List 64 Bar Code Label Sh 60 Figure 35, Lists 65 and 92 Bar Code Labels Sh 61 Figure 36, List 66 Bar Code Label Sh 62 Figure 37, List 67 Bar Code Label Sh 63 Figure 38, List 68 Bar Code Label Sh 64 Figure 39, List 69 Bar Code Label Sh 65 Figure 40, List 71 Bar Code Label

Sh 66 Figure 41, List 72 Bar Code Label Sh 67 Figure 42, List 73 Bar Code Label Sh 68 Figure 43, Lists 74 and 77 Bar Code Labels Sh 69 Figure 44, List 75 Bar Code Label Sh 70 Figure 45, List 76 Bar Code Label Sh 71 Figure 46, List 78 Bar Code Label Sh 72 Figure 47, List 79 Bar Code Label Sh 73 Figure 48, List 80 Bar Code Label

Sh 74 Figure 49, List 81 Bar Code Label Sh 75 Figure 50, List 82 Bar Code Label Sh 76 Figure 51, List 83 Bar Code Label Sh 77 Figure 52, List 85 Bar Code Label Sh 78 Figure 53, List 86 Bar Code Label Sh 79 Figure 54, Lists 87 and 91 Bar Code Labels Sh 80 Figure 55, List 88 Bar Code Label Sh 81 Figure 56, List 89 Bar Code Label Sh 82 Figure 57, List 90 Bar Code Label Sh 83 Figure 58, List 93 Bar Code Label Sh 84 Figure 59, List 94 Bar Code Label Sh 85 Figure 60, List 95 Bar Code Label Sh 86 Figure 61, List 96 Bar Code Label Sh 87 Figure 62, List 97 Bar Code Label Sh 88 Figure 63, List 98 Bar Code Label Sh 89 Figure 64, List 99 Bar Code Label Sh 90 Figure 65, List 100 Bar Code Label Sh 91 Figure 66, Adhesion Tester Sh 92 Figure 67, Bar Code Labels - Roll Form Layout Sh 93 Figure 68, Bar Code Labels - Layout Sheet Sh 94 Figure 69, Bar Code Labels - Layout Sheet Sh 95 Figure 70, Bar Code Labels - Layout Sheet Sh 96 Figure 71, Bar Code Labels - Layout Sheet Sh 97 Figure 72, Bar Code Labels - Layout Sheet Sh 98 Figure 73, Bar Code Labels - Layout Sheet Sh 99 Figure 74, Bar Code Labels - Layout Sheet Sh 100 Figure 75, Bar Code Labels - Layout Sheet Sh 101 Figure 76, Bar Code Labels - Layout Sheet


December 1, 1998

SHEET INDEX (continued)

NUMBERS TITLES

Sh 102 Figure 77, Bar Code Labels - Layout Sheet Sh 103 Figure 78, Bar Code Labels - Layout Sheet Sh 104 Figure 79, Bar Code Labels - Layout Sheet

Sh 105 Figure 80, Bar Code Labels - Layout Sheet Sh 106 Figure 81, Bar Code Labels - Layout Sheet Sh 107 Figure 82, Bar Code Labels - Layout Sheet Sh 108 Appendix A - Code 11 Symbology, element assignment Sh 109 Appendix B - Code 39 Symbology, element assignment

INFORMATION TO BE FURNISHED BY Lucent Technologies (c - As currently authorized)

OS-11150 c Observational StandardPKG-77SZ4604 c Packing SummaryLMD c Label Manufacturers Data provided by ACA at Gateway II, NewarkWL-2355 c Central Office Finishes - 827 FinishX-18719 c Central Office White Color Standard

REFERENCED AMERICAN NATIONAL STANDARDS

ANSI X3.182-1995Guideline for Bar Code Print Quality available from: American National Standards Institute, Inc.

1430 BroadwayNew York, New York 10018cost: $28/copy + $5 shipping & handling


CONTENTS

1. GENERAL ................................ ................................ ................................ ................................ ................................ ...................... 7

1.1 MANUFACTURIN REQUIREMENTS................................ ................................ ................................ ................................ ..............71.2 QUALIFICATION REQUIREMENTS................................ ................................ ................................ ................................ ..................71.3 ASSURANCE OF PRODUCT CONFORMANCE ................................ ................................ ................................ ................................ .71.4 TABLE OF LABEL LIST NUMBER CORRELATION ................................ ................................ ................................ .......................... 8

2. DESCRIPTION ................................ ................................ ................................ ................................ ................................ ............10

3. REQUIREMENTS ................................ ................................ ................................ ................................ ................................ .......16

3.1 QUALIFICATION ................................ ................................ ................................ ................................ ................................ .........163.2 GENERAL................................ ................................ ................................ ................................ ................................ ...................173.3 NATURE OF ADHESIVE ................................ ................................ ................................ ................................ .............................. 17

3.3.1 Adhesive strength ounces per inch (grams per centimeter) of width (label and tab) ................................ ........................ 173.4 DIMENSIONS ................................ ................................ ................................ ................................ ................................ ..............173.5 PRINTED BAR CODE ................................ ................................ ................................ ................................ ................................ ..173.6 PRINTED ALPHANUMERIC CHARACTERS................................ ................................ ................................ ................................ ....183.7 REFLECTIVITY AND CONTRAST (BAR CODE LABELS ONLY) ................................ ................................ ................................ ........203.8 EFFECT OF MOISTURE................................ ................................ ................................ ................................ ................................ 203.9 CORPORATE LOGOTYPE................................ ................................ ................................ ................................ ............................. 203.10 COLOR IDENTIFICATION................................ ................................ ................................ ................................ ........................... 20

4. METHODS OF TEST ................................ ................................ ................................ ................................ ................................ ..20

4.1 QUALIFICATION TESTS................................ ................................ ................................ ................................ ............................... 204.2 GENERAL................................ ................................ ................................ ................................ ................................ ...................214.3 NATURE OF ADHESIVE................................ ................................ ................................ ................................ ............................... 224.4 ADHESION STRENGTH................................ ................................ ................................ ................................ ................................ 224.5 DIMENSIONS ................................ ................................ ................................ ................................ ................................ ..............224.6 PRINTED BAR CODE ................................ ................................ ................................ ................................ ................................ ..224.7 PRINTED ALPHANUMERIC CHARACTERS................................ ................................ ................................ ................................ ....224.8 REFLECTIVITY AND CONTRAST................................ ................................ ................................ ................................ ..................224.9 EFFECT OF MOISTURE................................ ................................ ................................ ................................ ................................ 234.10 CORPORATE LOGOTYPE................................ ................................ ................................ ................................ ........................... 234.11 COLOR IDENTIFICATION................................ ................................ ................................ ................................ ........................... 23

5. PACKING AND MARKING................................ ................................ ................................ ................................ ....................... 23

5.1 PACKING AND MARKING................................ ................................ ................................ ................................ ............................ 235.2 QUANTITY ON PAGES................................ ................................ ................................ ................................ ................................ .245.3 QUANTITY ON ROLLS................................ ................................ ................................ ................................ ................................ .245.4 MARKING ................................ ................................ ................................ ................................ ................................ ..................24

5.4.1 Page Marking ................................ ................................ ................................ ................................ ................................ ....245.4.2 Roll Marking................................ ................................ ................................ ................................ ................................ ......24

6. CHANGES COVERED BY REISSUE OF SPECIFICATION ................................ ................................ ................................ 25

7. LABEL FORMAT FIGURES ................................ ................................ ................................ ................................ .....................25


December 1, 1998

1. GENERAL

This specification covers the engineering requirements for either a white background or a Central Office WhiteOS-11150 background, pressure sensitive, adhesive backed, Common Language Equipment Identification(CLEI) labels with Equipment Catalog Identifier (ECI) bar coded data in either, label only or label and tabcombinations.

KS-22002 list number data and updates are available to label manufacturers through the Lucent TechnologiesCustomer Information Center (CIC). The contact for label data is Mr. Jim Shirk (317) 322-6518, supervisor formicrofilm and microfiche, Department NN8421480. The label data files are generated by ACA at Gateway II,Newark. File names are: PRD15.NE10.LABLMFG.FILE for data on tape; PRD15.NE10.LABLMFG.FICH fordata on fiche.

Corporate identification via the corporate logotype is a significant issue, the requirements of Section 3.11 mustbe met.

1.1 Manufacturing RequirementsManufacturing Requirements are those mechanical, chemical, electrical, and other requirements for whichthere shall be evidence of conformance during production lot inspections. The mechanism for obtaining suchevidence is covered under the heading "Assurance of Product Conformance."

1.2 Qualification RequirementsQualification Requirements are those requirements which do not need evidence of conformance during productinspections. They are requirements a label manufacturer must comply with in order to become an approvedsupplier. Lucent Technologies Global Supply Line Management (GSLM) organization will evaluate productsfrom all potential suppliers with respect to those requirements and will retain the responsibility to repeat theevaluations as deemed necessary.

1.3 Assurance Of Product ConformancePreproduction and/or production samples may be required for product first manufactured to this KS-22002specification by the approved supplier or when changes to specification requirements, materials, manufacturingmethods, or manufacturing location are made. Samples are intended to establish product compliance tospecification requirements. Production samples will be inspected by the Lucent Technologies QualityManagement Services (QMS) organization. Unless otherwise directed, samples of all product failing to meet therequirements of the conformance tests shall be forwarded to the Lucent Technologies Global Supply LineManagement organization for further evaluation.

Product shipment will be deferred until production approval granted by the Lucent Technologies Global SupplyLine Management organization is received, through the Lucent Technologies Purchasing Organization, unlessthe (KS-22002) approved supplier has been advised in writing that "Shipment need not be withheld pendingproduction sample approval." Shipment of limited quantities in advance of formal production approval mayonly be authorized by the Lucent Technologies Global Supply Line Management organization through the QMSorganization.

Continuing conformance to this specification will be monitored by product inspections. The approved productsupplier will be notified by the QMS organization as to the frequency and types of these product inspections. Noproduct shall be shipped without inspection and approval by the QMS organization except as otherwiseauthorized by the QMS organization.


1.4 Table Of Label List Number CorrelationKS-22002 CLEI Label List Number Correlation

Code 11 Symbology Code 39 Symbology OverallLabelSize

Remarks

White C.O.W.(1) White C.O.W.(1) (See Notes: 1, 2, & 3)

01 18 --- --- .400" X 1.000" No logotype, basic Code 11 CLEI label, too small for Code 39

02 45 --- --- .400" X 1.000" No logotype, slit versions of Lists 01 & 18

04 --- 31 --- .400" X 2.040" No logotype, label surface will accept pen/pencil writing

05 --- 34 54 .400" X 2.000" No logotype, label surface will accept pen/pencil writing

06 --- --- --- .400" X 1.000" No logotype, List 1 label & tab combination

08 --- --- 32 .400" X 2.040" No logotype, label & tab combination

09 --- 35 --- .400" X 2.000" No logotype, label & tab combination

11 --- --- --- .400" X 1.500" No logotype, text lines block the use of Code 39 symbology

--- 12 --- 37 .600" X 2.715" Optional use of nomenclature "SER" on line 2

--- 13 --- 38 .600" X 2.715" Optional use of nomenclature "ISS" on line 3

--- 14 --- 39 .600" X 4.090" Optional use of nomenclature "SER" on line 2

--- 15 --- 40 .600" X 4.090" Optional use of nomenclature "ISS" on line 3

--- 16 --- --- .600" X 2.715" No logotype , use preferred List 25

--- 17 --- --- .600" X 2.715" LED cutout blocks the use of Code 39 symbology

19 --- 33 --- .400" X 2.040" No logotype & has 8 point text alphanumeric characters

20 --- 36 --- .400" X 2.000" No logotype & has 8 point text alphanumeric characters

--- 21 --- 41 .600" X 4.090" Lucent Technologies logotype at bottom of the labe

--- 22 --- --- .400" X 2.040" Lucent Technologies logotype blocks the use of Code 39 symbology

--- 23 --- 63 .400" X 2.000" All text characters are 0.94 inch high


--- 25 62 42 .600" X 2.715" Lucent Technologies logotype at bottom of the labe

--- 26 --- --- .600" X 2.709" LED cutout blocks the use of Code 39 symbology


--- --- 28 30 .400" X 1.100" No logotype, basic CLEI, label only Code 39 symbology

--- --- 29 44 .400" X 1.100" No logotype, slit versions of Lists 28 & 30

--- --- --- 43 .600" X 2.715" No logotype

------

------

------

4670

.587" X 2.805" " "

ll label printing resides in the top 2/3rds of both labels, however there are differentfonts on List 46 and List 70 text lines .

-- --- --- 47 .587" X 2.805" Mandatory use of the nomenclature "Fault"

--- --- --- 48 .587" X 2.805" Mandatory use of the nomenclature "Fault" & "Active"

49 50 --- --- .250" X 1.000" No logotype & replaces KS-23143 "overlay" label

--- --- 51 52 .250" X 1.100" No logotype & replaces KS-23143 "overlay" label

--- --- --- 53 .400" X 2.000" Designed for Code 39 symbology only

--- --- --- 55 .800" X 2.500" Two text lines,15 characters maximum each line

--- 56 --- --- .400" X 2.000" Print area too small for Code 39


December 1, 1998

KS-22002 CLEI Label List Number Correlation

Code 11 Symbology Code 39 Symbology OverallLabelSize

Remarks

White C.O.W.(1) White C.O.W.(1) (See Notes: 1, 2, & 3)

--- --- --- 57 .587" X 2.805" LED nomenclature detailed in PO, Single LED cutout

--- --- --- 58 .587" X 2.805" LED nomenclature detailed in PO, Two LED cutouts

--- --- 59 60 .400" X 1.000" Basic CLEI label using Condensed Code 39 symbology

--- --- --- 61 .400" X 2.000" Not for general use, logotype is offset from label center

--- --- --- 64 .400" X 2.000" No Lucent Technologies logotype, horizontal in-service position

--- --- 65 92 .400" X 1.600" Three lines for text

--- --- --- 66 .600" X 2.715" Lucent Technologies logotype in the middle of the labe

--- --- --- 67 .600" X 4.090" Internationally recognized "lock" & "unlock" symbols included

--- --- --- 68 .480" X 2.805" Mandatory use of the nomenclature "Fault" & "Active"

--- --- 69 --- .400" X 1.600" No Lucent Technologies logotype, four lines for text

--- --- --- 71 .700" X 1.100" Text & logotype are adjacent to the CLEI code & bar code symbo

--- --- 72 --- .620" X 2.960" One line for text, KS-23490 bar code symbols (SN & CC) included

--- --- --- 73 .745" X 1.219" No logotype, two lines for text above the bar code symbol

--- --- 74 77 .400" X 2.000" Not for general use, logotype is offset from label center

--- --- 75 --- .400" X 2.000" Top portion of label has an additional color for identification purposes

--- --- --- 76 .600" X 2.715" logotype is at label bottom, nomenclature is "ALM" & "OL

--- --- --- 78 .600" X 2.715" logotype is at label bottom, nomenclature is "ALM" & "ACT"

--- --- --- 79 .725" X 2.312" Mandatory use of nomenclature: "Fault" & "Active"

--- --- --- 80 .600" X 2.805" Clearance hole is offset from the label's center line

--- --- --- 81 .587" X 2.760" Similar to List 46 except 0.045" shorter in overall length



---

---

---

---

---

---

84

98

.587" X 2.760"

“

Similar to List 48 except 0.045" shorter in overall length, List 98

requires a different font size than List 84


--- --- --- 86 .600" X 4.090" Nomenclature "ALM" is adjacent to clearance hole

------

------

------

8791

.600" X 4.090" " "

Nomenclature "ALM", "CC1" & "CC0" are adjacent to slotNomenclature "ALM", "CC0" & "CC1" are adjacent to slot

--- --- 88 .400" X 2.500" Similar to List 64 except increased length accommodates more text

--- --- --- 89 .600" X 2.900" Die cut to form three labels, nomenclature "LC" is mandatory

--- --- --- 90 .600" X 2.000" Die cut to form two labels, logotype is on the top label

--- --- --- 93 .800” X 1.975” Mandatory use of nomenclature “Fault” & “Active”

--- --- --- 94 .620” X 2.960” Four lines for text, horizontal in-service position

--- --- --- 95 .587” X 1.860” Three lines for text, nomenclature “Fault” is mandatory

--- --- --- 96 .587” X 2.760” Used with List 85, no Lucent Technologies logotype

--- --- --- 97 .400” X 2.000” No logotype, horizontal in-service position

--- --- --- 99 .800” X 1.900” Five lines for text, bar code symbol is printed in vertical plane

--- --- --- 100 .587” X 2.000” Die cut to form two labels, logotype is on the top label

Notes:1. C.O.W. is Central Office White OS-11150.2. All labels have the logotype "Lucent" to denote Lucent Technologies unless specified otherwise.3. Lists: 3, 7 & 10 are either blank label stock or blank tab stock.


2. DESCRIPTIONThe List 1 label (Figure 1) consists of a properly spaced bar code symbol of Code 11 symbology (Appendix A) andseparate alphanumeric Common Language Equipment Identification (CLEI) code on a white background. Thelabel’s back is coated with a pressure-sensitive adhesive that is protected with a suitable release liner. The barcode and text to be imprinted on the label are specified by the Lucent Technologies BR document provided toCIC for use by all Lucent Technologies factories (BR 795 layer, 301-001 to 301-010). The label has the bar codeequivalent of 11 characters imprinted on its face, 2 dashes and a check digit follow the 6 digits of the ECI codeand a Start/Stop (S/S) character precedes and follows the 9 characters.

The List 2 label (Figure 1) is similar to List 1 label except it is die cut in half, horizontally.

The List 3 label is a white, blank label, identical in overall dimensions to List 1 and has a top surface which issuitable for writing on with either a pencil or ball point pen.

The List 4 label (Figure 3) includes all Code 11 print area information (Figure 1) with up to 3 lines of text, alocating dot on a white background and has a top surface which is suitable for writing on with either a pencil orball point pen.

The List 5 label (Figure 4) includes all Code 11 print area information (Figure 1) with up to 5 lines of text on awhite background and has a surface which is suitable for writing on with either a pencil or ball point pen.

The List 6 label (Figure 1) is a sheet of List 1 labels designated Sheet 1 and an associated sheet of tabsdesignated Sheet 2 (Figure 5). The 7 tab characters are specified on the purchase order.

The List 7 is a sheet of blank tabs, identical in overall size to the List 6 tabs.



The List 10 label is a blank, white label identical in overall dimensions to the List 4 label and has a top surfacewhich is suitable for writing on with either a pencil or ball point pen.

The List 11 label (Figure 6) includes: all Code 11 print area information (Figure 1) with up to 4 lines of text on awhite background and has a surface which is suitable for writing on with either a pencil or ball point pen.

The List 12 label (Figure 7) includes: all Code 11 print area information in a larger bar code print area (Figure2), the Lucent Technologies logotype (3.11), up to 3 lines of text and 1 line for series number on a Central OfficeWhite OS-11150 background.

Note: The larger bar code print area in Figure 2 increases bar code height for easier scanning.

The List 13 label (Figure 8) includes: all Code 11 print area information (Figure 2) with the Lucent Technologieslogotype (3.11), up to 3 lines of text and 1 line for issue number on a Central Office White OS-11150background.

The List 14 label (Figure 9) includes: all Code 11 print area information (Figure 2) with the Lucent Technologieslogotype (3.11), up to 2 lines of text and 1 line for series number on a Central Office White OS-11150background.

The List 15 label (Figure 10) includes: all Code 11 print area information (Figure 2) with the LucentTechnologies logotype (3.11), up to 3 lines of text and 1 line for issue number on a Central Office WhiteOS-11150 background.


December 1, 1998

The List 16 label (Figure 11) includes: all Code 11 print area information (Figure 2), with up to 2 lines of text, 1line for serial number and the nomenclature "ALM" on a Central White OS-11150 background. List 16 is notrecommended for general use utilize List 25 (Figure 17) instead.

The List 17 label (Figure 12) includes: all Code 11 print area information (Figure 2) with the LucentTechnologies logotype (3.11) up to 3 lines of text and the nomenclature "FAIL" on a Central Office WhiteOS-11150 background.

The List 18 label (Figure 1) is similar to the List 1 label except the label color is Central Office White OS-11150.

The List 19 label (Figure 3) includes: all Code 11 print area information (Figure 1) is similar to the List 4 labelexcept that all lines of text shall be 8 point Helvetica Condensed font on a white background and the surface issuitable for writing on with pencil or ball point pen.

The List 20 label (Figure 4) includes: all Code 11 print area information (Figure 1) is similar to the List 5 labelexcept all lines of text shall be 8 Point Helvetica Condensed font on a white background and the surface issuitable for writing on with pencil or ball point pen.

The List 21 label (Figure 13) includes: all Code 11 print area information (Figure 2) with the LucentTechnologies logotype (3.11) and up to 5 lines of text on a Central Office White OS-11150 background.



The List 24 (Figure 16) includes: all Code 11 print area information (Figure 1) with the Lucent Technologieslogotype (3.11) and up to 4 lines of text on a Central Office White OS-11150 background.

The List 25 label (Figure 17) includes: all Code 11 print area information (Figure 2) with the LucentTechnologies logotype (3.11), up to 4 lines of text and the nomenclature "ALM" on a Central Office WhiteOS-11150 background.

The List 26 label (Figure 18) includes: all Code 11 print area information (Figure 2) with the LucentTechnologies logotype (3.11), up to 3 lines of text and the nomenclature "ALM" on a Central Office WhiteOS-11150 background.

The List 27 label (Figure 19) includes: all Code 11 print area information (Figure 1) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a Central Office White OS-11150 background. This labelis not approved for Central Office use since the location of the Lucent Technologies logotype is not in accordancewith Lucent Technologies Central Office Industrial Design Standards and Guidelines.

The List 28 label (Figure 20) consists of a properly spaced bar code symbol of Code 39 symbology (Appendix B)and separate alphanumeric Common Language Equipment Identification (CLEI) code on a white background. The back of the label is coated with a pressure-sensitive adhesive that is protected with a suitable release liner. The bar code and text to be imprinted on the label are specified by the ECI code number and defined in LucentTechnologies Manufacturers Data Report. The label has the bar code equivalent of 8 characters imprinted onits face. These include 6 characters of the ECI code and a Start/Stop (S/S) character preceding and onefollowing the ECI characters.


The List 29 label (Figure 20) is similar to the List 28 label except it is also die cut in half, horizontally.

The List 30 label (Figure 20) is similar to the List 28 label except the color is Central Office White OS-11150.

The List 31 label (Figure 3) is similar to the List 4 label except the bar code symbology is Code 39 (Figure 20).

The List 32 label (Figure 3) is similar to the List 8 label except the bar code symbology is Code 39 (Figure 20),on a Central Office White OS-11150 background. Available in sheet form only; labels are on sheet 1, tabs are onsheet 2.



The List 35 label (Figure 4) is similar to the List 9 label except the bar code symbology is Code 39 (Figure 20).Available in sheet form only; labels on sheet 1; tabs on sheet 2.


The List 37 label (Figure 7) is similar to the List 12 label except the bar code symbology is Code 39 (Figure 21),with the Lucent Technologies logotype (3.11) on a Central Office White OS-11150 background.

NOTE: The larger bar code print area in Figure 21 increases bar code symbol height for easier scanning.






The List 43 label (Figure 22) includes: all Code 39 print area information (Figure 21) with up to 3 lines of text,and the nomenclature "FAIL" on a Central Office White OS-11150 background.

The List 44 label (Figure 20) is similar to List 29 except the label background color is Central Office WhiteOS-11150.

The List 45 label (Figure 1) is similar to List 2 except the label background color is Central Office WhiteOS-11150.


The List 47 label (Figure 24) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11), up to 4 lines of text and the nomenclature "FAULT" on a Central Office WhiteOS-11150 background.


December 1, 1998

The List 48 label (Figure 25) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11), up to 4 lines of text and the nomenclature "FAULT" and "ACTIVE" on a CentralOffice White OS-11150 background.

The List 49 label (Figure 26) includes a Code 11 bar code symbol and separate alphanumeric CommonLanguage Equipment Identification (CLEI) code on a white background. Label design is similar to the List 2label except there is no horizontal slit. The height of the label is equivalent to the maximum dimension of thelower portion of the List 2 label. The label is only used as a replacement for the discontinued KS-23143,Overlay label or for those products which cannot be labeled with the standard List 1 label.

The List 50 label (Figure 26) is similar to the List 49 label except the label color is Central Office WhiteOS-11150. Application requirements for the List 50 label are identical to the List 49 label.

The List 51 label (Figure 27) consists of Code 39 symbology and separate alphanumeric Common LanguageEquipment Identification (CLEI) code on a white background. Label design is similar to the List 29 label(Figure 20) except there is no horizontal slit and the height of the List 51 label is equivalent to the maximumdimension of the lower portion of the List 29 label. Application requirements for the List 51 label are identicalto the List 49 label.

The List 52 label (Figure 27) is similar to the List 51 label except the label color is Central Office WhiteOS-11150. Application requirements for the List 52 label are identical to the List 49 label.

The List 53 label (Figure 28) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11) and up to 4 lines of text on a Central Office White OS-11150 background

The List 54 label (Figure 4) is similar to the List 34 label except the label color is Central Office WhiteOS-11150.



The List 57 label (Figure 24) is similar to the List 47 label except the nomenclature below the LED cutoutcontains alphanumerics which are detailed in the ordering information.

The List 58 label (Figure 25) is similar to the List 48 label except the nomenclature below the 2 LED cutoutscontain alphanumerics which are detailed in the ordering information.

The List 59 label (Figure 31) includes a condensed Code 39 bar code symbol and separate alphanumericCommon Language Equipment Identification (CLEI) code on a white background. Overall label dimensions are0.4 inch by 1.0 inch. This label is only to be used in applications where insufficient space prevents the use of a0.40 inch by 1.10 inch label having conventional Code 39 symbology, use list 28 label for general labelingapplications.

The List 60 label (Figure 31) includes a condensed Code 39 bar code symbol and is similar to the List 59 labelexcept the label color is Central Office White OS-11150. Application requirements for List 60 are identical to List 59.

The List 61 label (Figure 32) contains all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11) and up to 6 lines of text, on a Central Office White OS-11150 background. Thislabel is intended to satisfy the on-site printing needs of the Oklahoma City Works and has dimensions per theirrequirements. This label is not recommended for general labeling applications due to the location of the LucentTechnologies logotype, which is not in accordance with Lucent Technologies Central Office Industrial Design


Standards and Guidelines.

The List 62 label (Figure 17) is similar to List 42 label except the label background color is white and the LucentTechnologies logotype (3.11) is included.

The List 63 label (Figure 33) includes: all Code 39 print area information (Figure 21) with up to 4 lines of text,with the Lucent Technologies logotype (3.11) on a Central Office White OS-11150 background.

The List 64 label (Figure 34) includes: all Code 39 print area information (Figure 20) with up to 3 lines of text,and the Interchangeability marking on a Central Office White OS-11150 background. The label is designed for ahorizontal placement with the lines of text extending away from the right-hand side of the bar code symbol.

The List 65 label (Figure 35) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a white background.


The List 67 label (Figure 37) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a Central Office White OS-11150 background. This labelcontains the universal symbols for "Lock" and "Unlock" along with a hole to accommodate a push button switch.

The List 68 label (Figure 38) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11), up to 4 lines of text, the nomenclature "FAULT" and "ACTIVE" on a Central OfficeWhite OS-11150 background.

The List 69 label (Figure 39) includes: all Code 39 print area information (Figure 21) with up to 4 lines of texton a white background.

The List 70 label (Figure 23) is similar to the List 46 label except the line number 2 text font and size isdifferent. The label color is Central Office White OS-11150 and the Lucent Technologies logotype (3.11) isincluded.

The List 71 label (Figure 40) includes: all Code 39 print area information (Figure 27) with the LucentTechnologies logotype (3.11) and up to 4 lines of text, on a Central Office White OS-11150 background.

The List 72 label (Figure 41) includes: Code 39 print area information (Figure 20), the Lucent Technologieslogotype (3.11) and 1 line of text on a white background. Along with the CLEI / ECI information List 72 has aserial number and a COMCODE. KS-23490 details the requirements for the serial number and COMCODE.

The List 73 label (Figure 42) includes: all Code 39 print area information (Figure 20) with up to 2 lines of texton a Central Office White OS-11150 background.

The List 74 label (Figure 43) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11) and up to 6 lines of text on a white background.

The List 75 label (Figure 44) includes: all Code 39 print area information (Figure 20) with up to 5 lines of texton a white background. Only 1 of 3 specific Pantone colors (3.12) shall be designated on the purchase order.

The List 76 label (Figure 45) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a Central Office White 0S-11150 background. Labeldesign has the nomenclature "ALM" and "OL" printed in a vertical plane adjacent to a groove in the label.



December 1, 1998

The List 78 label (Figure 46) is similar to the List 76 label except the nomenclature is " ALM" and "ACT ".

The List 79 label (Figure 47) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11), up to 3 lines of text and the nomenclature "FAULT" and "ACTIVE" on a CentralOffice White OS-11150 background.

The List 80 label (Figure 48) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a Central Office White OS-11150 background. This labelcontains the universal symbols for "Lock" and "Unlock" with a clearance hole to accommodate a push buttonswitch.

The List 81 label (Figure 49) is similar to the List 46 label except for a shorter overall length.






The List 87 label (Figure 55) includes: all Code 39 print area information (Figure 21) with the LucentTechnologies logotype (3.11) up to 3 lines of text and nomenclature "ALM", "CC1" and "CC0" on a Central OfficeWhite OS-11150 background.

The List 88 label (Figure 56) is similar to the List 64 except the overall length is longer to accommodate up to 15characters of text per line.

The List 89 label (Figure 57) includes: all Code 39 print area information (Figure 21) up to 2 lines of text andthe nomenclature "LC" on a Central Office White OS-11150 background.

The List 90 label (Figure 58) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11) and up to 2 of text on a Central Office White OS-11150 background. This label isdie cut into 2 separate labels.

The List 91 label (Figure 55) is similar to the List 87 label except the nomenclature "CC0" and "CC1" arereversed.


The List 93 label (Figure 59) includes: all Code 39 print area information (Figure 27) with the LucentTechnologies logotype (3.11), up to 4 lines of text and the nomenclature “FAULT” and “ACTIVE” on a CentralOffice White OS-11150 background.

The List 94 label (Figure 60) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11) and up to 3 lines of text on a Central Office White OS-11150 background. The labelis designed for a horizontal placement.

The List 95 label (Figure 61) includes: all Code 39 print area information (Figure 20) with the LucentTechnologies logotype (3.11), up to 3 lines of text and the nomenclature “FAULT” on a Central Office White OS-11150 background.


The List 96 label (Figure 62) includes up to 3 lines of text on a Central Office White OS-11150 background.

The List 97 label (Figure 63) includes: all Code 39 print area information (Figure 20) and up to 2 lines of text ona Central Office White OS-11150 background.

The List 98 label (Figure 52) includes: all Code 39 print area information (Figure 20) and up to 4 lines of textwith the Lucent Technologies logotype (3.11) and the nomenclature “FAULT” and “ACTIVE” on a Central OfficeWhite OS-11150 background.

The List 99 label (Figure 64) includes: all Code 39 print area information (Figure 20) with the LucentTechnologieslogotype (3.11) up to 4 lines of text on a Central Office White OS-11150 background.

The List 100 label (Figure 65) includes: all Code 39 print area information (Figure 20) with the LucentTechnologieslogotype (3.11) and up to 2 lines of text on a Central Office White OS-11150 background.

These labels are intended only for indoor use. If they are not subjected to direct sunlight, high humidity, and /or high temperatures, hey should have a useful life of 20 years after application.

The shelf-life (before application) of these labels is approximately 3 years if they are stored unopened, in theiroriginal plastic wrapping, free from exposure to direct light, in a clean area which has an ambient temperatureof 16 to 30 degrees C (60 to 100 degrees F), maximum 50 percent relative humidity.

Note 1:Extended storage at temperature above 80 degrees F is not advisable.Note 2:All labels are available in either sheet (see 5.2) or roll form (see 5.3) unless specified otherwise. Labeland tab combinations are available in sheet form only.

3. REQUIREMENTSThe labels and tabs shall be capable of meeting each of the requirements listed below when tested in accordancewith the related paragraph of Section 4, Methods of Test.

Observed or calculated values obtained from analysis, measurement, or test shall be rounded off in accordancewith the Rounding-Off Method per ASTM E 29 to the nearest unit in the last right-hand place of figures used inexpressing the specified limit.

Where reference is made to an ASTM Designation in this specification, the issue listed in the latest publishedASTM index to Standards shall apply unless otherwise specified.

3.1 QualificationIn order to qualify, a prospective supplier must submit sample labels and tabs in accordance with all therequirements of this specification. The sample bar code labels shall register a valid scan and have a minimumaverage initial adhesive strength of 25 ounces per inch (279 grams per centimeter) of width along with aminimum average adhesive strength of 40 ounces per inch (446 grams per centimeter) of width and bar codesymbol stability when conditioned and tested in accordance with paragraph 4.1. The tabs shall have the sameaverage adhesive strength, however, if the tab tears above 30 ounces per inch ( 335 grams per centimeter), afterit has been conditioned, it shall be considered as qualifying under this specification. Lucent TechnologiesGlobal Manufacturing & Engineering Supply Line Management Center will evaluate the labels with respect tothese requirements and will retain the responsibility to repeat the evaluation as deemed necessary. Small pilotruns and experimental product will not be considered as complying. Suppliers will be required to certify thatproduct furnished on a contract or purchase order is identical in basic material to that supplied for qualification.


December 1, 1998

Proposed changes in roll or sheet layout to increase quantity of labels per sheet or roll, to improve printingquality, or to reduce costs, shall be reviewed by design engineering. Samples representative of such proposalsshall be submitted to the Lucent Technologies Global Manufacturing & Engineering Supply Line ManagementCenter for initial approval.

3.2 GeneralEach label sample shall conform to the bar code symbol and alphanumeric character layout and theirdimensions as shown in the appropriate figure for each list number. The tab page layout shall conform to Figure5. They shall not show delamination, blistered areas, or chipped edges. The face of the labels and tabs mayhave a smooth light matte finish. The Lucent Technologies logotype, the bar code symbol(s) and allalphanumeric characters printed on each label shall be black. List 75 labels shall have their background colormatch 1 of 3 colors of the Pantone Color Matching System, as specified in 3.12. The label color for those listnumbers requiring Central Office White shall be Central Office White (-134), OS-11150 per X-18719.Observational Standard OS-11150 is a color chip of Central Office White with a smooth baked finish (827). Eachqualified vendor shall submit 5 color samples to Lucent Technologies, Global Bar Code Technology Group forinitial approval. All labels and tabs shall be easily separable from the release liner without damage. Bar codelabels shall be scannable for the specified symbology, smudge resistant, reasonably free from scratches, marks,dots or misplaced color and shall be reasonably flat. All labels shall have outside corner radii of 0.06 inch unlessotherwise specified.

3.3 Nature Of AdhesiveThe adhesive shall be pressure sensitive and permanent; it shall be applied in a uniform layer and be free frombubbles and foreign matter.

3.3.1 Adhesive strength ounces per inch (grams per centimeter) of width (labeland tab)

"Initial" Adhesive Strength After application and heatingtwo hours after application at 100 degrees C for 168 hours (*)

25.0 oz/in (279 g/cm) minimum 45.0 oz/in (446 g/cm) minimum

(*) If the tab tears above 30 oz/in (335 g/cm), it shall be judged as fulfilling the requirements.

3.4 DimensionsEach List number label shall conform to the dimensions shown in the appropriate Figure.

Media Thickness:

(a) Overall label thickness (but not including release liner) is 0.0075 inch (.190 mm) max. (1) Laminate thickness (when laminate present) = 0.001 inch (.025 mm) max.

(2) Laminate adhesive thickness (when laminate present) = 0.0005 inch (.012 mm) min. to 0.001 inch (.025 mm) max.

(3) Substrate thickness = 0.002 inch (.050 mm) min. to 0.004 inch (.106 mm) max.(4) Substrate adhesive thickness = 0.001 inch (.0254 mm) to 0.0015 inch (.038 mm) max.

(b) Overall tab thickness (but not including release liner) is 0.004 inch to 0.006 inch (0.10 to 0.15 mm).(1) Adhesive thickness = 0.0005 to 0.001 inch (0.015 to 0.25 mm).

3.5 Printed Bar CodeThe printed bar code symbologies covered by this specification shall be Code 11 (Appendix A), Code 39(Appendix B) or a condensed version of Code 39.


(a) The Code 11 symbology is a discrete bi-directional bar code with a modulo 11 sum check digit. The barcode structure, (Appendix A) includes the digits 0 through 9, the dash, and the start and stop (S/S)character. The narrow bar or space width is 0.0075 inch (0.188 mm). The wide bar or space width is 0.0168inch (0.42 mm). The extra wide bar is 0.0261 inch (0.675 mm). The bar code shall have an overall printquality grade of C (1.5/05/900 nm) or better in accordance with paragraph 3.9. The intercharacter gap is0.011 inch (0.28 mm). Each printed bar shall have a uniform diffuse density and be free of edge errors. Anedge error is either a void or a smear.

(b) The Code 39 symbology is a self-checking, discrete bi-directional bar code. The bar code structure,(Appendix B) includes the alphanumerics: 0-9, A-Z, Start/Stop (S/S), $,/,+ and %. The narrow bar or spacewidth is 0.0075 inch (0.18 mm). The wide bar or space width is 0.0168 inch (0.429 mm). Theintercharacter gap is 0.011 inch (0.28 mm). The bar code shall have an overall print quality grade of C(1.5/05/900 nm) or better in accordance with paragraph 3.9. Each printed bar shall have a uniform diffusedensity and be free of edge errors. An edge error is either a void or a smear.

(c) A condensed version of the Code 39 symbology is available on the Lists 59 and 60 labels. The narrow barwidth is 0.0065 inch (0.165 mm). The narrow space width is 0.008 inch (0.203 mm). The wide bar orspace width is 0.0162 inch (0.411 mm). The intercharacter gap is 0.008 inch (0.203 mm) and the QuietZones are 0.10 inch (2.540 mm). The bar code shall have an overall print quality grade of C (1.5/05/900nm) or better, in accordance with paragraph 3.9. Each printed bar shall have a uniform diffuse densityand be free of edge errors.

3.6 Printed Alphanumeric CharactersThe approved alphanumeric character fonts for KS-22002 labels are:

Bold Condensed Condensed Light Condensed

Helvetica Helvetica HelveticaTriumphant Triumphant TriumphantAutologic Geneva Autologic Geneva Autologic Geneva

Helvetica is the preferred alphanumeric character font while the other 2 fonts are approved equivalents.

When trademark identification characters are included on the label, the "Lucent Technologies Product Medium"font shall be used.

When the Lucent Technologies corporate logotype is required on a particular List number - see both theappropriate Figure for that List number and Requirement Section 3.11.

The alphanumeric characters on all labels and tabs shall be legibly printed and centrally located across thelabel/tab width unless otherwise specified below.

(a) The CLEI characters printed either below a horizontally scanned bar code or adjacent to a verticallyscanned bar code shall be OCR-B in accordance with American National Standard X3.49-1975 except themaximum character height shall be 0.080 inch (2.0 mm) and an inverted Q shall be used instead of theletter O.

(b) When a label contains any nomenclature such as: ALM, CC1, FAIL or FAULT, etc. those characters shallbe 8 point Helvetica Light Condensed.

(c) Tab characters for Lists 6, 8 and 9 shall be OCR-A in accordance with American National StandardX3.17-1981 computer printed using a half dot double density dot matrix with a density of 11 to 13characters per inch. The header strip shall simulate the header on the List 1 label sheet, but shall becomputer printed using standard dot matrix. The inverted Q shall be used in place of the letter O on thetabs and header strip of the tab sheet.


December 1, 1998

(d) Lists 4, 5, 8, 9, 22-24, 31, 32, 34, 35, 53, 54, 63, 71, 73 and 75 text characters shall be Helvetica BoldCondensed with a nominal height of 0.094 inch (2.39 mm).

(e) Lists 11 and 69 text characters shall be Helvetica Bold Condensed with a nominal character height of0.080 inch (2.0 mm). Line 1 of both labels shall have the characters centered, while the characters on theremaining 3 lines shall be left justified.

(f) Lists 14, 16, 17, 26, 39, 43, 66, 67, 76, 78 - 80, 86, 87, 91 and 95 - line 1 text characters shall be 12 pointHelvetica Bold Condensed, all characters on the remaining 2 lines shall be 10 point Helvetica LightCondensed.

(g) Lists 19, 20, 33 and 36 - all text characters shall be 8 point Helvetica Condensed.

(h) Lists 21 and 41 - line 1 text characters shall be 12 point Helvetica Bold Condensed, all characters on theremaining 4 lines shall be 10 point Helvetica Light Condensed.

(i) Lists 12, 25, 37, 42 and 62 line 1, text characters shall be 12 point Helvetica Bold Condensed, allcharacters on the remaining 3 lines shall be 10 point Helvetica Light Condensed.

(j) All List 27 text characters shall be Helvetica Bold Condensed with a nominal character height of 0.08 inch(2.0 mm). Characters printed on lines 1 and 2 shall be centrally located across the label width, while allcharacters printed on line 3 shall be left justified.

(k) Lists 13, 15, 38, 40, 46-48, 57, 58, 68 and 81-85, lines 1 and 2 shall have text characters in 12 pointHelvetica Bold Condensed, all characters on lines 3 and 4 shall be 10 point Helvetica Light Condensed.

(l) List 55 text characters shall be 10 point Helvetica Bold Condensed.

(m) Lists 56 and 96 text characters shall be 8 point Helvetica Light Condensed.

(n) List 61 text characters shall be Helvetica Light Condensed with a nominal character height of 0.084 inch(2.00 mm).

(o) Lists 64 and 88 text characters shall be 8 point Helvetica Light Condensed. However, theInterchangeability Marking shall be Helvetica Light Condensed with a nominal character height of 0.094inch (2.39 mm) and is positioned in an area to the right of the second text line.

(p) Lists 65 and 92 text characters shall be 8 point Helvetica Light Condensed.

(q) List 70 - line 1 text characters shall be 12 point Helvetica Bold Condensed while all text characters on theremaining 3 lines shall be 10 point Helvetica Light Condensed.

(r) List 72 text characters should be 8 point Helvetica Bold Condensed. Serial and COMCODE number textcharacters should be 6 point Helvetica Bold Condensed. Product family text characters specified on line 2(Figure 41) shall be right justified to align with the trailing edge of the CLEI bar code symbol. Whentrademarked identification characters are used, the text shall be positioned to begin 0.125 inches +/- 0.005inches from the right edge of the Lucent Technologies logo. See Figure 41 for additional text and logopositioning requirements.

(s) Lists 74 and 77 text characters shall be Helvetica Light Condensed with a nominal height of 0.080 inch.

(t) Lists 89, 90 and 100 - line 1 text characters shall be 12 point Helvetica Bold Condensed, line 2 textcharacters shall be 10 point Helvetica Light Condensed.


(u) List 93 - lines 1 and 2 text characters shall be 12 point Helvetica Bold Condensed also lines 3 and 4 textcharacters shall be 10 point Helvetica Light Condensed.

(v) List 94 - all text characters shall be 8 point Helvetica Bold Condensed.

(w) List 97 - line 1 text characters shall be 10 point Helvetica Light Condensed, line 2 text characters shall be0.080 inch high and Helvetica Light Condensed.

(x) List 98 - lines 1 and 2 shall have text characters in 10 point Helvetica Bold Condensed, all characters onlines 3 and 4 shall be 10 point Helvetica Light Condensed.

(y) List 99 - line 1 shall have text characters in 10 point Helvetica Bold Condensed, Line 2 shall have textcharacters in 8 point Helvetica Light Condensed, all characters on lines 3 and 4 shall be 6 point HelveticaLight Condensed.

3.7 Reflectivity and Contrast (bar code labels only)Bar code symbol reflectivity requirements shall be measured in the 900 nm (infrared) wavelength. Bar codesymbols shall have a minimum overall print quality grade of C (1.5/05/900 nm) as defined by American NationalStandard, ANSI X3.182. The "Modulation" profile reflectance parameter shall have a minimum print qualitygrade of D (> 40%). All other profile reflectance parameters shall have a minimum print quality grade of C. ForCode 11 symbology, individual print quality requirements for the following parameters shall be met:

Symbol Contrast > 40%Modulation > 40%Minimum Edge Contrast > 15%Defects < 25%

3.8 Effect of MoistureThe bar code symbol(s) on each label shall be scannable. All labels and tabs shall demonstrate an adhesionstrength of 40 ounces per inch (0.05 kilograms per millimeter) of width after exposure to relative humidity of 95percent at 50°C (120°F) for 96 hours. The labels shall also show no evidence of smudging, self-lifting,delaminating or discoloring after conditioning. If the tab tears above 30 ounces, it shall be judged as fulfillingthe requirement.

3.9 Corporate LogotypeWhen labels contain the corporate logotype, it shall be black in color and use only an approved proof of thecorporate logotype (approved by Lucent Technologies, BL Architect Division), never set the letters "Lucent" in ageneric typeface. Official brandmark artwork from Product Marking Repro 1 (PMR1), configuration 5, (availablefrom tel. 1-800-458-1761).

3.10 Color IdentificationThe List 75 label shall have one of the following colors as background for the text characters: Pantone ProcessYellow - C, Pantone Red - 185C or Pantone Blue - 290C

4. METHODS OF TEST

4.1 Qualification TestsThe label manufacturer shall provide either at least 5 sheets of labels or a total of 100 consecutive labels on aroll for the evaluation. Randomly selected labels will be tested in accordance with the following instructions.


December 1, 1998

Bar Code Symbol Testing

(a) The qualification tests for those labels using Bar Code Symbology Code 11, shall consist of the following.Scan at least 12 test labels as described in 4.7 using an approved bar code verifier that uses ANSI X3.182methodology and is capable of decoding Code 11 bar code symbology.

When using a verifier that uses ANSI X3.182 methodology, a label is judged to be scannable if the verifierreadout indicates a minimum overall print quality grade of C (1.5/05/900 nm) after 10 successful scans. The modulation profile reflectance parameter shall have a minimum print quality grade of D (> 40%). Allother profile reflectance parameters shall have a minimum print quality grade of C.

(b) The qualification tests for those labels using Bar Code Symbology Code 39, shall consist of the following: Scan at least 12 test labels with either Photographic Sciences Corp. (PSC) model QC500B, a PSC model650 or a RJS Inc., model Inspector IV, bar code symbol verifier. A label is judged to be scannable if theverifier readout indicates a minimum overall print quality grade of C (1.5/05/900 nm) after 10 successfulscans. The "Modulation" profile reflectance parameter shall have a minimum print quality grade of D (>40%). All other profile reflectance parameters shall have a minimum print quality grade of C.

(c) The qualification tests for those labels using the Lucent Technologies condensed version of Bar CodeSymbology Code 39 is scanning at least 12 test labels with a verifier that uses the ANSI X3.182methodology. A label is judged to be scannable if the verifier readout indicates a minimum overall printquality grade of C (1.5/05/900 nm). The modulation profile reflectance parameter shall have a minimumprint quality grade of D (> 40%). All other profile reflectance parameters shall have a minimum printquality grade of C.

Adhesive Measurement Methodology:Qualification testing includes an initial adhesive strength test, as well as, a adhesive strength test onenvironmentally conditioned labels.

Initial Adhesion Strength:Apply 3 test labels to one or more stainless steel panels in accordance with ASTM D 1000. In 2 hours + 10minutes, the adhesive strength shall be measured using a crosshead tensile tester making a 90-degreepeel at a rate of 2 inches (51 mm) per minute using wire or cord length of approximately 30 inches (762mm) between the upper crosshead clamp of the tensile tester and the clamp which grips the label undertest.

Adhesion Strength and Symbol Stability After Conditioning:Apply a total of 12 test labels to a group of 4 or more stainless steel panels in accordance with ASTM D1000. Place one-half (1/2) of the panels in a circulating air oven at 82 +3°C (180 +5°F) and the otherpanels in a chamber at 32 + 3°C (90 + 5°F) and 95 + 2 percent relative humidity. At the conclusion of 30days at the 2 exposure conditions, the labels shall show no evidence of self-lifting, delaminating, smudgingor discoloring. After this visual examination of the label samples, verify all bar code symbols inaccordance with 4.1(a), (b) or (c). Determine the adhesion strength by measuring the adhesive strength of3 test labels from each of the 2 exposure conditions group and averaging the results for an overall value.

4.2 GeneralThe minimum quantity of sample labels shall be either 5 sheets or 100 consecutive labels on a roll. Observevisually for defects to the labels such as improper die cutting, print smear, smudging, delamination then scanthe bar code symbols with a bar code scanner. Compare the scanner display for the SN and CC bar code symbolsto the alphanumeric characters that are printed adjacent to them, scanner display and printed alphanumericsmust match.


Compare the scanner display for the bar code to the numeric equivalent ECI number listed for thealphanumeric code (CLEI) printed beneath the bar code on the scanned label. The relationship between ECInumber and CLEI may also be checked after the label has been applied to the product. However, it is notrecommended that the verifier/analyzer be used for merely decoding the bar coded ECI datamessage. A commercially available scanner should be used for this purpose. All labels having CentralOffice White OS-11150, should be visually evaluated for color conformity using the Munsell Color Tolerance Setfor Finish No. 827, OS-11150. Test in accordance with X-18719, except that the color match shall be done withthe label sample affixed to a central office White OS-11150 surface. For labels with a portion of the backgroundcolor described by this specification as matching the "Pantone Color Matching System", that label portion mustbe visually compared with the appropriate color sample in the current "Pantone Color Formula Guide" andaccepted or rejected based on visual detection.

4.3 Nature of AdhesiveThe supplier shall certify that the adhesive is permanent, pressure sensitive, and is free from bubbles andforeign matter.

4.4 Adhesion StrengthObtain a rubber-covered steel roller and prepare at least 2 stainless steel panels per ASTM D 1000, Method A.

(a) Initial Adhesion Strength: Remove at least three labels or tabs from the release liner, apply them to 1or more stainless steel panels, and roll per ASTM D 1000 taking care to leave approximately 0.125 inch (3mm) of release liner on each label for clamping purposes. In 2 hours (+10 minutes, measure the adhesionstrength to conform to the requirements of 3.4 using a crosshead tensile tester making a 90-degree peel(Figure 40) at a rate of 2 inch (50 mm) per minute using a wire length of approximately 30 in (762 mm). Calculate the average value of adhesion.

(b) Adhesion Strength After Heating: Remove at least three labels or tabs from the release liner, applythem to 1 or more stainless steel panels, and roll per ASTM D 1000. Place the panel in an ovenmaintained at 100 degrees C. At the end of 168 hours, remove the panel and allow it to cool to roomtemperature. In 1 to 3 hours, measure the adhesion strength as to conform with the requirements of 3.4.

4.5 Dimensions(a) Overall Thickness: Use ASTM D 374, Method C as referenced and modified in ASTM D 1000. Measure

the thickness of the label or tab plus the release liner, the release liner alone, and obtain the label or tabthickness by subtraction.

(b) Adhesive Thickness Only: The supplier shall certify that the supplied labels comply with therequirement of 3.4 (a).

4.6 Printed Bar CodeANSI X3.182 bar code print quality technique: Program or configure the approved verifier for an effectivemeasurement aperture of 0.005 inch (0.127 mm) at a wavelength of 900 nm + 10 nm and proceed to scan theentire bar code symbol. Scan the bar code symbol once to determine the ANSI print quality grade. If either Dor F grade (less than 1.5) is obtained, then use the 10 scan average method as defined in ANSI X3.182 todetermine the final grade.

4.7 Printed Alphanumeric CharactersCompare the CLEI alphanumeric characters below the bar code to American National Standards ANSI X3.49.

4.8 Reflectivity and ContrastReflectivity and contrast measurements are made automatically when using an approved bar code verifier that


December 1, 1998

uses the ANSI X3.182 methodology and has an effective aperture of 0.005 inch (0.127 mm) at a wavelength of900 nm + 10 nm.

4.9 Effect of MoistureRemove at least three labels or tabs from the release liner, apply them to a stainless steel panel and roll perASTM D 1000. Allow the panel to stand for 2 hours. Transfer it to a humidity chamber having the specifiedconditions. Remove the panel at the end of the specified time, allow it to cool 1 to 3 hours, and examine thelabels visually. Scan as in paragraph 4.1 and measure adhesion strength using a crosshead tensile testermaking a 90-degree peel (Figure 40) at a rate of 2 inch (50 mm) per minute using a wire length of approximately30 inches (762 mm). Calculate the average value of adhesion.

4.10 Corporate LogotypeVisually examine the corporate logotype from 10 randomly selected labels for: color, font, location andadherence to the dimensional requirements as shown below.

(a) Label widths greater than 0.48 inch: Logotype overall dimensions shall be 0.101 inch high by 0.472 inchwide, with a tolerance of plus or minus 0.005 inch. Measure the “L” to determine height.

(b) Label widths equal to or smaller than 0.48 inch: Logotype overall dimensions shall be 0.064 inch high by0.279 inch wide, with a tolerance of plus or minus 0.005 inch. Measure the “L” to determine height.

(c) Lists 72 & 78 are the only exceptions to the above rules, they shall meet the dimensions of 4.11 (b).

4.11 Color IdentificationFor labels with Pantone color, visually inspect 10 randomly selected labels for adherence to the latest version ofthe Pantone color formula guide.

5. PACKING AND MARKING

5.1 Packing and MarkingThe KS-22002 Label shall be packed and marked in accordance with the latest issue of Lucent TechnologiesPacking Summary PKG-77SZ4604, except as specified below.Neither labels nor tabs shall transfer to the underside of a page if pages are stacked, or to the release linerunderside for roll form labels. Pages shall be packaged between two stiff cardboard liners and permanentlyheat-sealed in transparent plastic sheeting. Each roll shall be packaged between two stiff cardboard discs,which shall be secured to the roll with ties and placed within a reusable plastic bag. Each package shall containeither labels only or labels and tabs with the same ECI number. The packages shall be packed in containersthat will keep them flat and provide protection against damage during domestic shipment, handling, andstorage in reasonably dry, unheated quarters.


5.2 Quantity on PagesLabels and tabs shall be available on pages of release liner as follows:

List Quantity per page Figures

1-3,6,18,28-30,44,45,49-52,59,60 80 or 60 68 & 696-9,32,35 (tabs) 162 54,5,8-11,19,20,22-24,27,31-36,53,54,56,61,63-65,74,75,77,88,92 40, 30 or 40 70, 71 & 7712,13,16,17,25,26,37,38,42,43,46-48,57,58,62,66,68,70,72,76,78,80-85,90 18, 48 or 21 72, 73 & 8114,15,21,39-41,67,86,87,89 & 91 12, 15 or 34 74, 75 & 7655 & 73 20 7811 & 69 50 7971 35 8079 18 82

On all pages of labels, the matrix between the labels shall be removed, and all pages shall be punched forinsertion into a 3- or 4-hole loose-leaf binder. The dimensions for the spacing of punched holes in theabove-referenced Figures shall be considered as guidelines for use within the limits of functionality. The tabpages shall be collated on a one for one basis with the label pages on all List 6, 8, 9, 32 and 35 page sets. Tabsshall be preformatted through the release liner to facilitate separation into two tab pieces, each tab beingdie-cut to the liner.

5.3 Quantity on RollsAll labels except Lists: 6, 7, 8, 9, 10, 32 & 35 shall be available on a strip of release liner wound in roll form on toa core as shown in Figure 60. The rolls shall be available in quantities of 1000, 3000, 5000, 10,000 or 25,000labels per roll. The outside diameter of a roll shall not exceed 11-1/2 inches.

5.4 MarkingEach package of either pages or rolls shall be marked with the date of manufacture. The date shall be shown asa 4 digit number; the first 2 digits shall be the last 2 numbers of the current year, the last 2 the current weekcounting from the beginning of the year.

5.4.1 Page MarkingEach page of either labels or tabs shall be marked as shown in the appropriate Figure, with the followinginformation: KS-22002 L (number); COMCODE NUMBER, with digits 3 through 8 inclusive underlined;specified equipment designation; and CLEI code identification, as appropriate. The dimensions for marginlettering are guidelines to be used within the limits of functionality.

5.4.2 Roll MarkingMarking for each roll of labels shall consist of the label identification information specified in paragraph 5.6 andshall also include the quantity of labels on the roll. In addition, if a separate packaging comcode is assigned toroll form labels, the package comcode shall also be included. This information shall be marked on the inside ofthe core, on the outside of each of the cardboard discs used for packing and at the top of the reusable plastic bag.

The end or side of the shipping container shall be marked with the quantity of labels, whether on PAGES orROLLS, KS-22002 L (number) COMCODE NUMBER, the supplier's name or trademark, lot number, and dateof manufacture. In addition, if a separate packaging comcode is assigned to roll form labels, the packagecomcode shall also be marked on the shipping container.


December 1, 1998

6. CHANGES COVERED BY REISSUE OF SPECIFICATION

Issue 24: The following changes have been included:

(a) Addition of the following bar code labels: Lists 93, 94, 95, 96, 97, 98, 99 and 100.

7. LABEL FORMAT FIGURESThe following label formats illustrate specific label dimensional requirements.


XXXXXXXXXX

0.215 ±±±± 0.005

+0.007

-0.0200.255

0.36

0

Slit for Lists 2 & 45use label bottom edgefor reference point

+0.0900.200

-0.005

0.061 ±±±± 0.005

0.122 ±±±± 0.005

0.132 ±±±± 0.040

0.40

0 ± ±±±

0.01

0

1.000 ±±±± 0.006

0.722 ±±±± 0.0050.135 ±±±± 0.015

+0.0

30

-0.0

10

0.0549 (Note E)

+0.0

000.

080 -0

.010

SHEET NOTESA. Code 11 symbology (Appendix A).B. Every label / area printing may have 2 dashes as shown.C. Lists 18 & 45 have central Office White OS-1115 as background color.D. Only Lists 2 & 45 have a horizontal slit.E. The 10 CLEI characters should be evenly spaced with a minimum character separation of 0.010 inch.F. All labels shall have a 0.06 radius on all corners.G. Bars may extend to the labels’ edge for the Lists 1, 2, 6, 18 and 45 labels.H. No printed border lines are required for either a label or in area printing.I. All dimensions are in inches, and point out the print area requirements both for ECI bar code symbol and

CLEI code when they are printed on a larger label, moreover this Figure is not drawn to scale.

LISTS 1, 2, 6, 18 & 45 BAR CODE LABELS / AREA PRINTINGFIGURE 1


December 1, 1998

XXXXXXXXXX

+0.0000.080

-0.010

0.061 ±±±± 0.0050.122 ±±±± 0.005

0.132 ±±±± 0.040

0.60

0 ± ±±±

0.00

6

1.000 ±±±± 0.006

0.722 ±±±± 0.0060.135 ±±±± 0.015

0.47

8+0.

030

-0.0

10

0.29

0 ± ±±±

0.00

7

0.25

0 ± ±±±

0.00

5

0.0549 (See B)

SHEET NOTESA. Code 11 symbology (Appendix A).B. Every label / area printing may have 2 dashes as shown.C. The 10 characters should be evenly spaced with a minimum character separation of 0.010 inch.D. No printed border lines are required.E. All dimensions are in inches, moreover this Figure is not drawn to scale.

CODE 11 BAR CODE AREA PRINTINGFIGURE 2


Bar

cod

e sy

mb

olpr

int

area

(N

otes

A&

B)

Use edge as reference for print area dimensions

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXX

XXXXXX

XX

XX

XX

XX

X

1.33

9 ± ±±±

0.01

5

1.57

4 ± ±±±

0.01

5

1.71

5 ± ±±±

0.01

5

1.85

6 ± ±±±

0.01

5

2.04

0 ± ±±±

0.01

0

Th

e 2

das

hes

may

be

used

wit

h C

ode

11,

neve

r w

ith

Cod

e 39

sym

bolo

gy

Dot

dia

met

er is

0.0

30”

SHEET NOTESA. Lists 4, 8 & 19 use Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. Lists 31, 32 & 33 use Code 39 symbology (Appendix B), see Figure 20 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. Lists 19 & 33 use 8 point Helvetica Condensed with a 5 character per line maximum.F. Lists 4, 8, 31, & 32 use Helvetica Bold Condensed with a nominal height of 0.094 inch and a 5 character

per line maximum.LISTS 4, 8, 19, 31, 32 & 33 BAR CODE LABELS

FIGURE 3


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

otes

A&

B)

Use edge as reference for print area dimension

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXX

XXXXX

XXXXX

XXXXX Line 5

Line 4

XX

XX

XX

XX

XX

1.15

1 ± ±±±

0.01

5

1.29

2 ± ±±±

0.01

5

1.57

4 ± ±±±

0.01

5

1.71

5 ± ±±±

0.01

5

1.85

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

The

2 d

ashe

s m

ay b

e us

ed w

ith

Cod

e 11

,ne

ver

wit

h C

ode

39 s

ymbo

logy

SHEET NOTESA. Lists 5, 9 & 20 use Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. Lists 34, 35, 36 & 54 use Code 39 symbology (Appendix B), see Figure 20 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. Lists 20 & 36 use 8 point Helvetica Condensed with a 5 character per line maximum.F. Lists 5, 9, 34, 35 & 54 use Helvetica Bold Condensed with a nominal height of 0.094 inch and a 5 character

per line maximum.

LISTS 5, 9, 20, 34, 35, 36 & 54 BAR CODE LABELSFIGURE 4


1.000

6.750

.750 1.375 2.125 2.125 1.375 .750 1.00010.625

0.375 XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

XXXXXXX

SHEET NOTESA. All dimensions are in inches, moreover this Figure is not drawn to scale.

LISTS 6, 8, 9, 32 & 35 TABS LAYOUT SHEETFIGURE 5


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)


XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1 (centered)

XXXXX

XXXXXXXXXX

Line 4

XX

XX

XX

XX

XX

1.03

0 ± ±±±

0.01

5

1.15

0 ± ±±±

0.01

5

1.27

0 ± ±±±

0.01

5

1.39

0 ± ±±±

0.01

5

1.50

0 ± ±±±

0.01

0

SHEET NOTESA. List 11 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. Alphanumeric text characters are 0.080 inch high, tolerances are: plus 0.000 inch and minus 0.005 inch.E. The font shall be Helvetica bold Condensed with 5 characters per line maximum.

LIST 11 BAR CODE LABELFIGURE 6


Bar

cod

e sy

mbo

lpr

int

area

(Not

es A

&B

)

Lea

ding

edg

e of

the

fir

st b

ar in

the

bar

cod

e sy

mbo

l

0.600 ±±±± 0.006

Line 3

Line 2

Line 1XXXXX

XXXXXXXXXX

Line 4

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

1.82

0 ± ±±±

0.01

5

2.10

5 ± ±±±

0.01

5

2.31

0 ± ±±±

0.01

5

The

2 d

ashe

s m

ay b

e us

ed w

ith

Cod

e 11

neve

r w

ith

Cod

e 39

sym

bolo

gy

XXXXX

1.41

5 ± ±±±

0.01

5

2.50

5 ± ±±±

0.01

5

2.17

5 ± ±±±

0.01

0

Lucent

SHEET NOTESA. List 12 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. List 37 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).F. If either the characters "SER" are to be printed on line 2 or the characters "ISS" are to be printed on line 3,

this information must be included with the ordering informationG. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H.Lines 2, 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum

LISTS 12 & 37 BAR CODE LABELSFIGURE 7


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(Not

es A

&B

)

Lea

ding

edg

e of

the

firs

t bar

in th

e ba

r co

de s

ymbo

l

0.600 ±±±± 0.006

Line 3

Line 2

Line 1XXXXX

XXXXXXXXXX

Line 4

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

1.82

0 ± ±±±

0.01

5

2.10

5 ± ±±±

0.01

52.

310

± ±±± 0.

015

The

2 d

ashe

s m

ay b

e us

ed w

ith

Cod

e 11

neve

r w

ith

Cod

e 39

sym

bolo

gy

XXXXX1.

415

± ±±± 0.

015

2.50

5 ± ±±±

0.01

5

2.17

5 ± ±±±

0.01

0

Lucent

SHEET NOTESA. List 13 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. List 38 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C: All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).F. If the characters "ISS" are to be printed on line 3, this information must be included with the ordering

informationG. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.H. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum



Bar

cod

e sy

mbo

lpr

int a

rea

(Not

es A

&B

)

Lea

ding

edg

e of

the

first

bar

inth

e ba

r co

de s

ymbo

l0.600 ±±±± 0.006

Line 2

Line 1XXXXXXXXXX

Line 3X

XX

XX

XX

XX

X

0.360 ±±±± 0.015

3.20

0 ± ±±±

0.01

5

3.68

5 ± ±±±

0.01

5

The

2 d

ashe

s m

ay b

e us

ed w

ith C

ode

11ne

ver

with

Cod

e 39

sym

bolo

gy

XXXXX

2.09

0 ± ±±±

0.01

5

3.87

5 ± ±±±

0.01

5

4.09

0 ± ±±±

0.01

0

Lucent

SHEET NOTESA. List 14 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. List 39 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black and the "L" shall be 0.101 inch high (see 4.11).F. If the characters "SER" are to be printed on line 2, this information must be included with the ordering

information.G. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

otes

A&

B)

Lea

ding

edg

e of

the

fir

st b

ar in

the

bar

cod

e sy

mbo

l

0.600 ±±±± 0.006

Line 3

Line 2

Line 1XXXX

XXXX

XXXX

Line 4

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

3.20

0 ± ±±±

0.01

5

3.48

0 ± ±±±

0.01

5

3.68

5 ± ±±±

0.01

5

The

2 d

ashe

s m

ay b

e us

ed w

ith

Cod

e 11

neve

r w

ith

Cod

e 39

sym

bolo

gy

XXXX

2.09

0 ± ±±±

0.01

5

3.87

5 ± ±±±

0.01

5

4.09

0 ± ±±±

0.01

0

Lucent

SHEET NOTESA. List 15 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. List 40 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black and the "L" shall be 0.101 inch high (see 4.11).F. If the characters "ISS" are to be printed on line 3, this information must be included with the ordering

information.G. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.H. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.600 ±±±± 0.006

Line 3

Line 2

Line 1 XXXXX

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

2.71

5 ± ±±±

0.01

0

2.14

5 ± ±±±

0.00

5

1.02

3 ± ±±±

0.01

0

1.95

0 ± ±±±

0.00

5

1.46

0 ± ±±±

0.00

5

ALM

XXXXXXX

XXXXXXX 1.34

7 ± ±±±

0.01

00.223 ±±±± 0.010

0.312 ±±±± 0.010

1.33

0 ± ±±±

0.00

51.

010

± ±±± 0.

005

+0.030

-0.0100.478

SHEET NOTESA. List 16 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. All 6 outside label corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The nomenclature will always be "ALM" as shown with a 8 point Helvetica Light Condensed font.E. Not recommended for general use because the Lucent Technologies logotype is missing, use List 25.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.600 ±±±± 0.006

Line 3

Line 2

Line 1 XXXXX

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

2.71

5 ± ±±±

0.01

0

2.14

5 ± ±±±

0.00

5

1.02

3 ± ±±±

0.01

0

1.95

0 ± ±±±

0.00

5

1.46

0 ± ±±±

0.00

5

FAIL

XXXXXXX

XXXXXXX 1.34

7 ± ±±±

0.01

00.223 ±±±± 0.010

0.312 ±±±± 0.010

1.39

5 ± ±±±

0.00

5

0.94

5 ± ±±±

0.00

5

+0.030

-0.0100.478

Lucent

0.10

0 ± ±±±

0.01

0

SHEET NOTESA. List 17 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. All 6 outside label corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature will always be "FAIL" as shown with 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

otes

A&

B)

Lea

ding

edg

e of

the

fir

st b

ar in

the

bar

cod

esy

mbo

l

XXXXX

0.600 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXX

XXXXX

XXXXXLine 4

XX

XX

XX

XX

XX

2.80

0 ± ±±±

0.01

5

3.00

0 ± ±±±

0.01

5

3.87

5 ± ±±±

0.01

5

4.09

0 ± ±±±

0.01

0

3.20

0 ± ±±±

0.01

5Line 5

3.68

5 ± ±±±

0.01

5

0.100 ±±±± 0.015

0.36

0 ± ±±±

0.01

5

XXXXX

Lucent

The

2 d

ashe

s m

ay b

e us

ed w

ith

Cod

e 11

neve

r w

ith

Cod

e 39

sym

bolo

gy

SHEET NOTESA. List 21 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. List 41 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C. All labels shall have a 0.06 radius on all corners.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black and the "L" shall be 0.101 inch high (see 4.11).F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2, 3, 4 & 5 shall have a 10 point Helvetica Bold Condensed font with a 7 character per line maximum



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.10

0 ± ±±±

0.01

5

1.85

6 ± ±±±

0.01

5

2.04

0 ± ±±±

0.01

0

1.57

4 ± ±±±

0.01

5

1.71

5 ± ±±±

0.01

5


Lucent

SHEET NOTESA. List 22 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. This label is not recommended for "FASTECH" faceplates because the label length is too long, use List 24.F. Lines 1, 2 & 3 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5 character perline maximum.



Bar

cod

e sy

mbo

lpr

int a

rea

(Not

e A

)XXXXX

0.400 ±±±± 0.006

Line3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.15

1 ± ±±±

0.01

5

1.81

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.67

5 ± ±±±

0.01

5


Lucent

XXXXX Line 4

1.53

4 ± ±±±

0.01

5

1.29

2 ± ±±±

0.01

5

SHEET NOTESA. List 23 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3 & 4 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5 characterper line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.06

0 ± ±±±

0.01

5

1.81

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.67

5 ± ±±±

0.01

5


Lucent

XXXXX Line 4

1.53

4 ± ±±±

0.01

5

1.39

3 ± ±±±

0.01

5

SHEET NOTESA. List 24 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3 & 4 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5 characterper line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.600 ±±±± 0.006

Line 4

Line 2

Line 1 XXXXX

XX

XX

XX

XX

X

0.360 ±±±± 0.015

2.71

5 ± ±±±

0.01

0

2.14

5 ± ±±±

0.00

5

1.02

3 ± ±±±

0.01

0

1.95

0 ± ±±±

0.00

5

1.46

0 ± ±±±

0.00

5

ALM

XXXXXXX

XXXXXXX 1.34

7 ± ±±±

0.01

00.223 ±±±± 0.010

0.312 ±±±± 0.0051.33

0 ± ±±±

0.00

51.

010

± ±±± 0.

005

+0.030

-0.0100.478

Line 3 XXXXXXX

1.66

0 ± ±±±

0.00

5

0.10

0 ± ±±±

0.01

0

Lucent

SHEET NOTESA. List 25 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. Lists 42 and 62 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.C. All 6 outside label corners shall have a 0.06 radius and both inside corners shall have a 0.102 radius.D. All dimensions are in inches, moreover this Figure is not drawn to scale.E. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).F. The nomenclature shall be "ALM" as shown with 8 point Helvetica Light Condensed font.G. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H. Lines 2,3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.

LISTS 25, 42 & 62 BAR CODE LABELSFIGURE 17


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.600 ±±±± 0.006

Line 2

Line 1 XXXXX

XX

XX

XX

XX

X

0.195 ±±±± 0.015

2.70

9 ± ±±±

0.01

0

2.49

5 ± ±±±

0.01

5

1.23

0 ± ±±±

0.01

5

2.14

0 ± ±±±

0.00

5

1.50

0 ± ±±±

0.00

5

ALM

XXXXXXX

0.350 ±±±± 0.005

0.320 ±±±± 0.005

1.28

0 ± ±±±

0.00

5

0.88

0 ± ±±±

0.00

5

+0.030

-0.0100.478

Line 3 XXXXXXX

1.94

0 ± ±±±

0.00

5

Lucent

0.200

SHEET NOTESA. List 26 uses Code 11 symbology (Appendix A), see Figure 2 for dimensional details.B. All 6 outside corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "ALM" as shown with 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX0.400 ±±±± 0.006

Line 3 (left)

Line 1 (centered)

XXXXXXXXXX

XX

XX

XX

XX

XX

1.00

0 ± ±±±

0.01

5

1.38

5 ± ±±±

0.01

5

1.50

0 ± ±±±

0.01

0

1.14

5 ± ±±±

0.01

5

1.26

5 ± ±±±

0.01

5


Lucent

Line 2 (centered)

SHEET NOTESA. List 27 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. This label is not approved for Central Office use because the Lucent Technologies logotype placement is inviolation of the Central Office Industrial Design Standards and Guidelines.F. Line 3 characters shall be printed Left justified, while Lines 1 and 2, characters shall be centrally located acrossthe label width.G. Lines 1, 2 & 3 shall have Helvetica Bold Condensed font with a 5 character per line maximum.H. Alphanumeric characters are 0.080 inch high, tolerances are: plus 0.000 inch & minus 0.005 inch.I. This label does not have dashes following the CLEI code.



December 1, 1998

XXXXXXXXXX

0.215 ±±±± 0.005

+0.007

-0.0200.255

0.36

0

Slit for Lists 29 & 44use label bottom edgefor reference point

+0.0900.200

-0.0050.132 ±±±± 0.040

0.40

0 ± ±±±

0.01

0

1.100 ±±±± 0.006

0.840 ±±±± 0.0050.130 ±±±± 0.015

0. 549 (Note E)

+0.0

000.

080 -0.0

10

+0.0

30

-0.0

10SHEET NOTESA. Code 39 symbology (Appendix B).B. Dashes shall not be part of either the CLEI code or the ECI bar code symbol.C. Lists 30 & 44 have central Office White OS-1115 as background color.D. Only Lists 29 & 44 have a horizontal slit.E. The 10 CLEI characters should be evenly spaced with a minimum character separation of 0.010 inch.F. All labels shall have a 0.06 radius on all corners.G. Bars may extend to the labels’ edge for the Lists 28, 29, 30 and 44 labels.H. No printed border lines are required for either a label or in area printing.I. All dimensions are in inches, and point out the print area requirements both for ECI bar code symbol and CLEI

code when they are printed on a larger label, moreover this Figure is not drawn to scale.


XXXXXXXXXX

+0.0000.080

-0.010

0.132 ±±±± 0.040

0.60

0 ± ±±±

0.00

6

1.100 ±±±± 0.006

0.840 ±±±± 0.0060.130 ±±±± 0.015

0.47

8+0.0

30

-0.0

100.

290

± ±±± 0.

007

0.25

0 ± ±±±

0.00

5

0.0549 (See B)

SHEET NOTESA. Code 39 symbology (Appendix B).B. No dashes shall be used in the CLEI code.C. The 10 characters should be evenly spaced with a minimum character separation of 0.010 inch.D. No printed border lines are required.E. All dimensions are in inches, moreover this Figure is not drawn to scale.

CODE 39 BAR CODE AREA PRINTINGFIGURE 21


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.600 ±±±± 0.006

Line 3

Line 2

Line 1 XXXXX

XX

XX

XX

XX

XX

0.360 ±±±± 0.015

2.71

5 ± ±±±

0.01

0

2.20

5 ± ±±±

0.00

5

1.02

3 ± ±±±

0.01

0

2.01

0 ± ±±±

0.00

5

1.52

0 ± ±±±

0.00

5

FAIL

XXXXXX

XXXXXX 1.34

7 ± ±±±

0.01

00.223 ±±±± 0.010

0.312 ±±±± 0.0101.45

5 ± ±±±

0.00

5

1.00

5 ± ±±±

0.00

5

+0.030

-0.0100.478

SHEET NOTESA. List 43 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The nomenclature shall be "FAIL" as shown with 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

Lea

ding

edg

e of

the

fir

st b

arin

the

bar

cod

e sy

mbo

l

0.587 ±±±± 0.006

Line 3

Line 2

Line 1XXXXX

XXXXXXXXXXXX

Line 4X

XX

XX

XX

XX

X

+0.030

2.20

5 ± ±±±

0.01

5

2.34

5 ± ±±±

0.01

5

2.48

5 ± ±±±

0.01

5

0.98

0 ± ±±±

0.01

5

2.64

5 ± ±±±

0.01

5

2.80

5 ± ±±±

0.01

0

Lucent

XXXXXXX

-0.0100.454

1.23

0 ± ±±±

0.01

0

SHEET NOTESA. Lists 46 and 70 use Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.F. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.G. List 46, Line 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H. List 70, Line 2 shall have a 10 point Helvetica Light Condensed font with a 7 character maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

0.587 ±±±± 0.006

Line 2

Line 1 XXXXXX

XX

XX

XX

XX

XX

2.80

5 ± ±±±

0.01

0

2.64

5 ± ±±±

0.01

0

0.342 ±±±± 0.010

0.980 ±±±± 0.010

2.20

5 ± ±±±

0.01

0

1.23

0 ± ±±±

0.01

0

Line 3 XXXXXXX

2.48

5 ± ±±±

0.01

0

Lucent

XXXXXX

XXXXXXX

2.34

5 ± ±±±

0.01

0

0.950 ±±±± 0.010

0.660 ±±±± 0.010

0.540 ±±±± 0.010

0.454 ±±±± 0.015

Line 4

FAULT

SHEET NOTESA. Lists 47 and 57 use Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. For List 47, the nomenclature shall be "FAULT" as shown with 8 point Helvetica Light Condensed font.F. For List 57, there will be a “Line 5" in 8 point Helvetica Light Condensed font with a 7 characters maximum.F. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.G. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.

LISTS 47 & 57 BAR CODE LABELS FIGURE 24


Bar

cod

esy

mbo

l pri

ntar

ea (

Not

e A

0.587 ±±±± 0.006

Line 2

Line 1 XXXXXX

XX

XX

XX

XX

XX

2.80

5 ± ±±±

0.01

0

2.64

5 ± ±±±

0.01

5

.210 ±±±± 0.010

2.20

5 ± ±±±

0.01

5

.540

± ±±± 0

.015

Line 3

XXXXXXX

2.48

5 ± ±±±

0.01

5

Lucent

XXXXXX

2.34

5 ± ±±±

0.01

5

.342 ±±±± 0.010

Line 4

FAULT

XXXXXXX.9

80 ± ±±±

0.0

15

1.23

0 ± ±±±

0.01

5

ACTIVE

.500

± ±±± 0

.010

.660

± ±±± 0

.010

.950

± ±±± 0

.010

.090 ±±±± 0.015

SHEET NOTESA. Lists 48 and 58 use Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 8 outside corners shall have a 0.06 radius, the 4 inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. For List 48, the nomenclature shall be "FAULT" and "ACTIVE" in 8 point Helvetica Light Condensed.F. For List 58, rather than nomenclature, there will be “Lines 5 & 6" in 8 point Helvetica Light Condensed fontwith a 7 character per line maximum.G. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.H. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

XXXXXXXXXX

+0.030

-0.0000.150

0.020 Min.

0.061 ±±±± 0.0050.122 ±±±± 0.0050.132 ±±±± 0.040

0.29

0 M

ax

1.000 ±±±± 0.006

0.722 ±±±± 0.005

0.0549 (Note D)

0.135 ±±±± 0.015

0.070 MIN

0.020 MIN

SHEET NOTESA. Code 11 symbology (Appendix A).B. Every label may have 2 dashes as shown.C. List 50 has Central Office White as background color.D. The 10 CLEI characters should be evenly spaced with a minimum character separation of 0.010.E. All labels shall have a 0.06 radius on all corners.F. Bars shall extend to the labels’ edge for both Lists 49 and 50.G. No printed border lines are required.H. All dimensions are in inches , moreover this Figure is not drawn to scale.



XXXXXXXXXX

+0.030

-0.0000.150

0.020 Min.

0.132 ±±±± 0.040

0.29

0 M

ax

1.100 ±±±± 0.006

0.840 ±±±± 0.005

0.549 (Note D)

0.130 ±±±± 0.015

0.070 Min.

0.020 Min.

SHEET NOTESA. Code 39 symbology (Appendix B).B. Dashes shall not be part of either the CLEI code or the ECI bar code symbol.C. List 52 has Central Office White as background color.D. The 10 CLEI characters should be evenly spaced with a minimum character separation of 0.010.E. All labels shall have a 0.06 radius on all corners.F. Bars shall extend to the labels’ edge for both Lists 51 and 52.G. No printed border lines are required.H. All dimensions are in inches , moreover this Figure is not drawn to scale



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.10

0 ± ±±±

0.01

5

1.81

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.67

5 ± ±±±

0.01

5


Lucent

XXXXX Line 4

1.53

4 ± ±±±

0.01

5

1.39

3 ± ±±±

0.01

5

SHEET NOTESA. List 53 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3 & 4 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5 characterper line maximum.



2.500+0.010

-0.000


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.32

5 ± ±±±

0.01

5

1.86

5 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.73

0 ± ±±±

0.01

5


Lucent

XXXXX Line 4

1.59

5 ± ±±±

0.01

5

1.46

0 ± ±±±

0.01

5Line 5

Line 6

XXXXXXXXXX

1.19

0 ± ±±±

0.01

5

1.00

0 ± ±±±

0.01

5

SHEET NOTESA. List 56 uses Code 11 symbology (Appendix A), see Figure 1 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Lines 1, 2, 3, 4, 5 & 6 shall use an 8 point Helvetica Light Condensed font and a 6 character per line maximum.



XXXXXXXXXX+0.007

0.21

5 ± ±±±

0.00

50.132 ±±±± 0.040

0.40

0 ± ±±±

0.01

0

1.000 ±±±± 0.006

0.800 ±±±± 0.005

0.549 (Note E)

0.100 ±±±± 0.015

+0.0

00

-0.0

100.

080

-0.0200.255

0.36

0+0.0

30

-0.0

10

SHEET NOTESA. Condensed version of Code 39 symbology (see 3.7 Requirements).B. Dashes shall not be part of either the CLEI code or the ECI bar code symbol.C. List 60 has Central Office White OS-1115 as background color.D. These labels are not recommended for general use - they are application dependent. For general CLEI

product marking use, Lists 28 and 30 are recommended.E. The 10 CLEI characters should be evenly spaced with a minimum character separation of 0.010 inch.F. All labels shall have a 0.06 radius on all corners.G. Bars may extend to the labels’ edge for both Lists 59 and 60.H. No printed border lines are required.I. All dimensions are in inches, moreover this Figure is not drawn to scale.

KS-22002 LISTS 59 & 60 BAR CODE LABELSFIGURE 31


December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.37

0 ± ±±±

0.01

5

1. 7

70 ± ±±±

0.0

15

2.00

0 ± ±±±

0.01

0

1.67

0 ± ±±±

0.01

5


Lucent

XXXXX Line 4

1.57

0 ± ±±±

0.01

5

1.47

0 ± ±±±

0.01

5Line 5

Line 6

XXXXXXXXXX

1.27

0 ± ±±±

0.01

5

1.13

0 ± ±±±

0.01

5

SHEET NOTESA. List 61 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3, 4, 5 & 6 shall use Helvetica Light Condensed font with a nominal height of 0.084 inch and a 5character per line maximum.



Bar

cod

e sy

mbo

l pri

ntar

ea (

Not

e A

)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

X

1.15

1 ± ±±±

0.01

5

1.81

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.67

5 ± ±±±

0.01

5


Lucent

XXXXX Line 41.

534

± ±±± 0.

015

1.29

2 ± ±±±

0.01

5

SHEET NOTESA. List 63 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3 & 4 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5 characterper line maximum.



December 1, 1998

XXXXXXXXXX0.160 ±±±± 0.015

0.28

0 ± ±±±

0.01

5

0.40

0 ± ±±±

0.00

6

0.900 ±±±± 0.015

0.130 ±±±± 0.015

XXXXXXX

XXXXXXX

XXXXXXX

XX:XX

0.350 ±±±± 0.015

2.000 ±±±± 0.010

Bar code symbol print area (Note A)

0.040 ±±±± 0.015

Line 1

Lines 2&4

Line 3

SHEET NOTESA. List 64 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. Lines 1, 2 & 3 shall have 8 point Helvetica Light Condensed font with a maximum of 7 characters per line.E. The Interchangeability Code (Line 4) shall appear in the 0.35 inch wide portion of the label, to the direct right ofLine 2, characters shall be 0.094 inch high in Helvetica Light Condensed font.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.13

0 ± ±±±

0.01

5

1.47

0 ± ±±±

0.01

5

1.60

0 ± ±±±

0.01

0

1.27

0 ± ±±±

0.01

5

1.37

0 ± ±±±

0.01

5


Lucent

SHEET NOTESA. Lists 65 and 92 use Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. The Lucent Technologies logotype reference line is 1.130 inches away from the label bottom.F. Lines 1, 2 & 3 shall use 8 point Helvetica Light Condensed font with a 6 character per line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.600 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXXXX

XX

XX

XX

XX

XX

1.70

0 ± ±±±

0.01

5

2.50

0 ± ±±±

0.01

5

2.17

5 ± ±±±

0.01

0

2.14

0 ± ±±±

0.01

5

2.34

0 ± ±±±

0.01

5


Lucent

Lea

ding

edg

e of

the

firs

t bar

in t

he b

ar c

ode

sym

bol

0.200 ±±±± 0.015

SHEET NOTESA. List 66 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional detailsB. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.F. Lines 2 & 3 shall have a 10 point Helvetica Bold Condensed font with a 7 character per line maximum



Bar

cod

e sy

mbo

lpr

int

area

(Not

e A

)

0.600 ±±±± 0.006

Line 3

Line 2

Line 1 XXXXX

XX

XX

XX

XX

XX

4.09

0 ± ±±±

0.01

5

3.87

5 ± ±±±

0.01

5

3.68

5 ± ±±±

0.01

5

3.20

0 ± ±±±

0.01

5

0.30

0 ± ±±±

0.01

0

1.65

0 ± ±±±

0.01

5

XXXXX

XXXXX 0.44

0 in

ch c

lear

ance

hole

Bar

cod

e sy

mbo

lpr

int

area

XX

XX

XX

XX

XX

XXXXXXXXXX

XXXXX

0.100 ±±±± 0.015

Lea

ding

edg

e of

the

firs

t ba

rin

the

bar

cod

e sy

mbo

l

Lucent Lucent0.36

0 ± ±±±

0.01

5

SHEET NOTESA. List 67 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Height of the "Lock" and "Unlock" figures is 0.100 inch and their faceplate positions should produce a pleasinglabel appearance.F. Height and position of the figures representing push buttons should produce a pleasing label appearance.G. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

Bar

cod

esy

mbo

l pri

ntar

ea (

Not

e A

)

.480 ±±±± 0.006

Line 2

Line 1 XXXX

XX

XX

XX

XX

X

2.80

5 ± ±±±

0.01

0

2.64

5 ± ±±±

0.01

5

.210 ±±±± 0.010

2.20

5 ± ±±±

0.01

5

.540

± ±±± 0

.015

Line 3

XXXX

2.48

5 ± ±±±

0.01

5

Lucent

XXXX

2.34

5 ± ±±±

0.01

5

.288 ±±±± 0.010

Line 4

FAULT

XXXX.9

80 ± ±±±

0.0

15

1.23

0 ± ±±±

0.01

5

ACTIVE

.500

± ±±± 0

.010

.660

± ±±± 0

.010

.950

± ±±± 0

.010

.090 ±±±± 0.015

Use

edg

e as

ref

eren

ce f

orpr

int

area

dim

ensi

ons

SHEET NOTESA. List 68 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All 8 outside corners shall have a 0.06 radius, all 4 inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. The nomenclature shall be "FAULT" and "ACTIVE" as shown with 8 point Helvetica Light Condensed font.G. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 4 character per line maximum.H. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 5 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(Not

e A

)

XXXXX0.400 ±±±± 0.006

Line 3

Line 1 (centered)

XXXXXXXXXX

XX

XX

XX

XX

XX

1.13

0 ± ±±±

0.01

5

1.49

0 ± ±±±

0.01

5

1.60

0 ± ±±±

0.01

0

1.25

0 ± ±±±

0.01

5

1.37

0 ± ±±±

0.01

5


Line 2

Line 4XXXXX

SHEET NOTESA. List 69 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. All text characters shall be Helvetica Bold Condensed font, 0.080 inch high, and a 5 character per linemaximum, tolerances are: plus 0.000 inch and minus 0.005 inch.



December 1, 1998

XXXXX

0.145 ±±±± 0.015

Line 1

0.700 ±±±± 0.010

Bar

cod

e pr

int

area

(N

ote

A)

Lucent

5 characters max.per line

Line 2

Line 3

Line 4

XXXXXXXXXXXXXXX

1.10

0 ± ±±±

0.01

0

0.86

1 ± ±±±

0.01

5

0.72

0 ± ±±±

0.01

5

0.57

9 ± ±±±

0.01

5

0.43

6 ± ±±±

0.01

5

0.400 ±±±± 0.015

XX

XX

XX

XX

XX

Use

edg

es a

s re

fere

nces

for

pri

nt a

rea

dim

ensi

ons

SHEET NOTESA. List 71 uses Code 39 symbology (Appendix B), see Figure 27 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. All text characters shall be Helvetica Bold Condensed with a nominal height of 0.094 inches at 5 characters perline maximum.F. Lucent Technologies logotype and all text characters shall be center justified in the area provided.



XXXXXXXXXXXXXXXXXXXXXX

0.21 ±±±± 0.01

1.30 ±±±± 0.01

0.62

± ±±± 0

.01

2.96 ±±±± 0.01

0.125 min.1.60 ±±±± 0.01

1.96 ±±±± 0.01

0.125 min.

XXXXXXXXXXXX

1.50 ±±±± 0.01

XXXXXXXXXLucent-CC

Lucent-SN

Lucent

XXXXXXXXXX

XXXXXXXXXXX

LINE 3 - A single line of 0.80” high product description text shall bepositioned here with 0.025” above and below the text. Text may not beplaced within 0.125” of the CLEI bar code symbol. LINE 1 - CLEI text shall be centered and

positioned 0.02” below the bar code symbol.Text shall be 0.08” (0.07” min) high.LINE 4 - Lucent serial number text should be positioned 0.01”

above the bar code symbol. Text should be 0.06” high.

LINE 5 - Lucent COMCODE number text shall be centered vertically between the serial number andCOMCODE number bar code symbols with a minimum of 0.01” above and below the text. Text shallbe 0.06” high.

The height of the logo shall be 0.064”. Logobottom shall be aligned with the bottom of theproduct family text.

LINE 2 - The top edge of the product family text characters shall be aligned with the top edge of the COMCODE bar code symbol. Trademarkedidentification characters shall be positioned to begin 0.125” ±±±± 0.005” fromthe right edge of the Lucent logo. Non trademarked identification charactersshall be right justified to align with the trailing edge of the CLEI bar code symbol. All character heights should be 0.080”. When trademarkedidentification characters are required, the “Lucent Product Medium” fonshall be used.

Bar code height 0.150+0.000-0.005



December 1, 1998

XXXXXXXXXXXXXXX

1.219 ±±±± 0.010

0.74

5 ± ±±±

0.01

0

Use edge as reference for print areadimensions

XXXXXXXXXXXXXXX

X X X X X X X X X X

Bar code symbol printarea (Note A)

0.59

5 ± ±±±

0.01

5

0.44

5 ± ±±±

0.01

5

Line 1

Line 2

SHEET NOTESA. List 73 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. Lines 1 & 2 shall have a Helvetica Bold Condensed font with a nominal height of 0.094 inch with a 15 characterper line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXX

XX

XX

XX

XX

X 1.40

0 ± ±±±

0.01

5

1.80

0 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.70

0 ± ±±±

0.01

5


Lucent

XXXX Line 4

1.60

0 ± ±±±

0.01

5

1.50

0 ± ±±±

0.01

5Line 5

Line 6

XXXXXXXX

1.30

0 ± ±±±

0.01

5

1.10

0 ± ±±±

0.01

5

SHEET NOTESA. Lists 74 and 77 use Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.064 inch high (see 4.11).E. Lines 1, 2, 3, 4, 5 & 6 shall use Helvetica Light Condensed font with a nominal height of 0.080 inch and a 5character per line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXX

0.400 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXXX

XX

XX

XX

XX

X

1.15

1 ± ±±±

0.01

5

1.85

6 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

0

1.71

5 ± ±±±

0.01

5


Line 4

1.57

4 ± ±±±

0.01

5

1.29

2 ± ±±±

0.01

5Line 5

XXXXXXXX

1.10

0 ± ±±±

0.01

5

Thi

s ar

ea h

as a

sta

ndar

d“w

hite

” ba

ckgr

ound

Bac

kgro

und

colo

r, in

this

are

a, s

hall

be o

neof

the

thre

e de

scri

bed

in N

ote

E.

SHEET NOTESA. List 75 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The area behind the CLEI code and bar code symbol shall be white in color.E. Background color behind the text characters shall be one of the following: Pantone Process Yellow - C, PantoneRed - 185C or Pantone Blue - 290C.F. Lines 1, 2, 3, 4, & 5 shall use Helvetica Bold Condensed font with a nominal height of 0.094 inch and a 5character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.600 ±±±± 0.006

XXXXXXXXXX

XX

XX

XX

XX

XX

Leading edge of the first bar in the bar codesymbol

Line 3

Line 2

Line 1

0.40

0 ± ±±±

0.01

5

2.35

5 ± ±±±

0.01

5

2.15

5 ± ±±±

0.01

5

1.13

0 ± ±±±

0.01

5

0.80

0 ± ±±±

0.01

5

Lucent

LO

ALM

0.27

5 ± ±±±

0.01

0

0.100 ±±±± 0.015

0.400 ±±±± 0.010

2.55

5 ± ±±±

0.01

5

2.71

5 ± ±±±

0.00

6

0.97

5 ± ±±±

0.01

5

Position bothnomenclatureswithout violatingthe Quiet Zoneor the logotype

SHEET NOTESA. List 76 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners and both inside corners shall have a 0.06 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "ALM" and "OL" as shown with a 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.600 ±±±± 0.006

XXXXXXXXXX

XX

XX

XX

XX

XX

Leading edge of the first bar in the bar codesymbol

Line 3

Line 2

Line 1

0.40

0 ± ±±±

0.01

5

2.35

5 ± ±±±

0.01

5

2.15

5 ± ±±±

0.01

5

1.13

0 ± ±±±

0.01

5

0.80

0 ± ±±±

0.01

5

Lucent

ACT

ALM

0.27

5 ± ±±±

0.01

00.100 ±±±± 0.015

0.400 ±±±± 0.010

2.55

5 ± ±±±

0.01

5

2.71

5 ± ±±±

0.00

6

0.97

5 ± ±±±

0.01

5

Position bothnomenclatureswithout violatingthe Quiet Zoneor the logotype

SHEET NOTESA. List 78 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners and both inside corners shall have a 0.06 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "ALM" and "ACT" as shown with a 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum



XXXXX

0.725 ±±±± 0.010

XXXXXXXX

ACTIVE

0.626 ±±±± 0.015

Lucent

FAULT

Line 1

Line 2

XXXXXXXX

XX

XX

XX

XX

XLine 3

2.31

2 ± ±±±

0.01

5

2.15

0 ± ±±±

0.01

5

2.02

1 ± ±±±

0.01

5

1.05

0 ± ±±±

0.01

5

0.346 ±±±± 0.015

0.81

8 ± ±±±

0.01

5

0.666 ±±±± 0.015

0.526 ±±±± 0.015

0.286 ±±±± 0.010

0.76

3 ± ±±±

0.01

0

0.57

8 ± ±±±

0.01

50.

125

± ±±± 0.

015

SHEET NOTESA. List 79 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 5 outside corners shall have a 0.06 radius and the inside corner shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "FAULT" and "ACTIVE" as shown with a 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

XXXXX

0.600 ±±±± 0.006

Lucent

Line 1

XX

XX

XX

XX

XX

0.234 ±±±± 0.010

XXXXXLine 2

XXXXXLine 3

2.20

5 ± ±±±

0.01

5

2.34

5 ± ±±±

0.01

5

2.64

5 ± ±±±

0.01

5

2.80

5 ± ±±±

0.01

5

1.23

0 ± ±±±

0.01

5

0.98

0 ± ±±±

0.01

5

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

Lea

ding

edg

e of

the

fi

rst b

ar in

the

bar

code

sym

bol

0.375 ±±±± 0.010

0.350 Clearance hol

Loc

atio

ns f

or t

he in

tern

atio

nals

ymbo

ls “

lock

” an

d “u

nloc

k”ar

e ap

prox

. Siz

e is

0.3

00 h

igh

SHEET NOTESA. List 80 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Height of the "Lock" and "Unlock" figures is 0.100 inch and their faceplate positions should produce a pleasinglabel appearance.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.587 ±±±± 0.006

Line 3Line 2

Line 1

XXXXXXXXXXXX

XX

XX

XX

XX

XX

2.16

0 ± ±±±

0.01

5

2.76

0 ± ±±±

0.01

0

2.60

0 ± ±±±

0.01

5

2.44

0 ± ±±±

0.01

5

2.30

0 ± ±±±

0.01

5

0.95

5 ± ±±±

0.01

5

Lea

ding

edg

e of

the

fir

st b

ar in

the

ba

r co

de s

ymbo

l

Lucent

XXXXXXX Line 4

1.18

5 ± ±±±

0.01

5

SHEET NOTESA. List 81 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.F. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXX

0.587 ±±±± 0.006

XXXXXX

XXXXXXX

XX

XX

XX

XX

XX

Lucent

XXXXXXX

Line 3

Line 2

Line 1

2.16

0 ± ±±±

0.01

5

2.76

0 ± ±±±

0.01

0

2.60

0 ± ±±±

0.01

5

2.44

0 ± ±±±

0.01

5

2.30

0 ± ±±±

0.01

5

Line 4

FAUL

0.342 ±±±± 0.010

0.502 ±±±± 0.015

0.622 ±±±± 0.015

0.912 ±±±± 0.015

0.955 ±±±± 0.015

1.18

5 ± ±±±

0.01

5

SHEET NOTESA. List 82 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners shall have a 0.06 radius, both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "FAULT" as shown and the required font is 8 point Helvetica Light Condensed.F. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.G. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXX

0.587 ±±±± 0.006

XXXXXXXXXXXXX

XX

XX

XX

XX

XX

Lucent

XXXXXXX

Line 3

Line 2

Line 12.

160

± ±±± 0.

015

2.76

0 ± ±±±

0.01

0

2.60

0 ± ±±±

0.01

5

2.44

0 ± ±±±

0.01

5

2.30

0 ± ±±±

0.01

5

Line 4

XXXXX

0.342 ±±±± 0.010

0.502 ±±±± 0.015

0.622 ±±±± 0.015

0.912 ±±±± 0.015

0.955 ±±±± 0.015

1.18

5 ± ±±±

0.01

5

0.454 ±±±± 0.015

SHEET NOTESA. List 83 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 6 outside corners shall have a 0.06 radius while both inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.F. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.G. Line 5 shall have a 8 point Helvetica Light Condensed font with a 8 character maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXX

0.587 ±±±± 0.006

XXXXXXXXXXXXX

XX

XX

XX

XX

XX

Lucent

XXXXXXX

Line 3Line 2

Line 12.

160

± ±±± 0.

015

2.76

0 ± ±±±

0.01

0

2.60

0 ± ±±±

0.01

5

2.44

0 ± ±±±

0.01

5

2.30

0 ± ±±±

0.01

5

Line 4

FAULT

0.44

0 ± ±±±

0.01

0

0.62

2 ± ±±±

0.01

0

0.95

5 ± ±±±

0.01

5

0.342 ±±±± 0.0100.502 ±±±± 0.015

1.18

5 ± ±±±

0.01

5

ACTIVE

0.91

2 ± ±±±

0.01

0

0.150 ±±±± 0.0100.030 ±±±± 0.015

SHEET NOTESA. Lists 84 and 98 use Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 8 outside corners shall have a 0.06 radius and the 4 inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "FAULT" and "ACTIVE" as shown with a 8 point Helvetica Light Condensed font.F. List 84 lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.G. List 98 lines 1 & 2 shall have a 10 point Helvetica Bold Condensed font with a 7 character per line maximum.H. For both List 84 & 98, lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character perline maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXX

0.587 ±±±± 0.006

XXXXXXXXXXXXX

XX

XX

XX

XX

XX

Lucent

XXXXXXX

Line 3Line 2

Line 12.

160

± ±±± 0.

015

2.76

0 ± ±±±

0.01

0

2.60

0 ± ±±±

0.01

5

2.44

0 ± ±±±

0.01

5

2.30

0 ± ±±±

0.01

5

Line 4

XXXXXX0.

440

± ±±± 0.

010

0.62

2 ± ±±±

0.01

5

0.95

5 ± ±±±

0.01

5

0.454 ±±±± 0.015

0.502 ±±±± 0.015

1.18

5 ± ±±±

0.01

5

0.91

2 ± ±±±

0.01

5

0.150 ±±±± 0.0100.030 ±±±± 0.0150.342 ±±±± 0.010

XXXXXX

Line 6

Line 5

SHEET NOTESA. List 85 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All 8 outside corners shall have a 0.06 radius and the 4 inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font with a 6 character per line maximum.F. Lines 3 & 4 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.G. Lines 5 & 6 shall be detailed with the ordering information and printed in 8 point Helvetica Light Condensedfont with a 8 character per line maximum.



December 1, 1998

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.600 ±±±± 0.006

XXXXXXX

XXXXXXX

XX

XX

XX

XX

XX

Lea

ding

edg

e of

the

fir

st b

ar in

the

ba

r co

de s

ymbo

l Line 3

Line 2

Line 1

Lucent

ALM

4.09

0 ± ±±±

0.01

5

3.87

5 ± ±±±

0.01

5

3.68

5 ± ±±±

0.01

5

3.20

0 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

5

0.36

0 ± ±±±

0.01

5

2.77

0 ± ±±±

0.01

0

0.10

0 ± ±±±

0.01

5

0.50

0 ± ±±±

0.01

5

SHEET NOTESA. List 86 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "ALM" as shown with 8 point Helvetica Light Condensed font.F. Horizontal position of the nomenclature “ALM” should produce a pleasing label appearance.G. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.H. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum



XXXX

0.600 ±±±± 0.006

XX

XX

XX

XX

XX

4.09

0 ± ±±±

0.01

0

~

XXXXX

XXXXX

. . . . . . .

8 Point HelveticaLightCondensed

ALM

CC1

CC0

Lucent

0.350 ±±±± 0.0100.100 ±±±± 0.010

Remove thisSection

3.87

5 ± ±±±

0.01

5

3.68

5 ± ±±±

0.01

5

3.20

0 ± ±±±

0.01

5

2.00

0 ± ±±±

0.01

5

1.16

0 ± ±±±

0.01

5

0.760 ±±±± 0.0150.360 ±±±± 0.015

0.475 ±±±± 0.0100.100 ±±±± 0.015

1.20

0 R

EF

0.85

0 ± ±±±

0.01

0

R (2 Places)

Line 3

Line 2

Line 1

SHEET NOTESA. Lists 87 and 91 use Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all outside corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. List 87 nomenclature shall be "ALM", "CC1" and "CC0" as shown in 8 point Helvetica Light Condensed font.F. List 91 nomenclature shall be "ALM", "CC0" and "CC1" (top to bottom) in 8 point Helvetica Light Condensedfont.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Lines 2 & 3 shall have a 10 point Helvetica Light Condensed font with a 7 character per line maximum.



December 1, 1998

XXXXXXXXXX0.040 ±±±± 0.015

0.24

0 ± ±±±

0.01

5

0.40

0 ± ±±±

0.00

6

0.900 ±±±± 0.015

0.130 ±±±± 0.015

XX------XX XXX

0.350 ±±±± 0.015

2.000 ±±±± 0.010


0.040 ±±±± 0.015

Lines 1 & 4

Line 2

Line 3

XX--------------XX

XX--------------XX

SHEET NOTESA. List 88 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. Line 1 shall have 8 point Helvetica Light Condensed font with an 8 character maximum.E. Lines 2 & 3 shall have 8 point Helvetica Light Condensed font with a 12 characters per line maximum.F. Line 4 shall appear in the 0.35 inch wide portion of the label, to the direct right of Line 1, characters shall be 8point Helvetica Light Condensed font with a maximum of 3 characters.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXX

0.587 ±±±± 0.006

Line 2

Line 1

LucentX

XX

XX

XX

XX

X

2.00

0 ± ±±±

0.01

5

2.90

0 ± ±±±

0.01

0

2.74

0 ± ±±±

0.01

5

2.58

0 ± ±±±

0.01

5

2.20

0 ± ±±±

0.01

5

0.90

0 ± ±±±

0.01

0

Lea

ding

edg

e of

the

fir

st b

ar in

the

bar

code

sym

bol

1.03

0 ± ±±±

0.01

5

XXXXXXX

LC

0.200 ±±±± 0.015

Die

cut

for

labe

l sep

arat

ion

SHEET NOTESA. List 89 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "LC" as shown with 10 point Helvetica Bold Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Line 2 shall have a 10 point Helvetica Light Condensed font with a 7 character maximum.



December 1, 1998

2.00

0 ± ±±±

0.01

0

Die cut forlabel separation

0.587 ±±±± 0.006

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXXX

Lucent

XX

XX

XX

XX

XX

XXXXXXXX

0.400 ±±±± 0.006

Line 1

Line 2

1.76

0 ± ±±±

0.01

5

1.60

0 ± ±±±

0.01

5

1.20

0 ± ±±±

0.01

5

1.10

0 ± ±±±

0.00

6

SHEET NOTESA. List 90 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Line 1 shall have a 10 point Helvetica Bold Condensed font with a 7 character maximum.F. Line 2 shall have a 8 point Helvetica Bold Condensed font with a 8 character maximum.



Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXX

0.800 ±±±± 0.006

XXXXXXXX

XX

XX

XX

XX

XX

Lucent

XXXX

Line 3Line 2Line 1

1.30

0 ± ±±±

0.01

5

1.97

5 ± ±±±

0.00

6

1.72

0 ± ±±±

0.01

5

1.58

0 ± ±±±

0.01

5

1.44

0 ± ±±±

0.01

5

Line 4

FAULT

0.62

5 ± ±±±

0.01

5

1.00

0 ± ±±±

0.01

5

0.61

0 ± ±±±

0.00

60.250 ±±±± 0.006

ACTIVE0.17

5 ± ±±±

0.01

5

0.285 ±±±± 0.015

0.130 ±±±± 0.015

0.160 ±±±± 0.0060.

450

± ±±± 0.

006

0.100 ±±±± 0.015

0.90

0 ± ±±±

0.00

6

SHEET NOTESA. List 93 uses Code 39 symbology (Appendix B), see Figure 27 for dimensional details.B. All 8 outside corners shall have a 0.06 radius all 4 inside corners shall have a 0.102 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "FAULT" and “ACTIVE” as shown with 8 point Helvetica Light Condensed font.F. Lines 1 & 2 shall have a 12 point Helvetica Bold Condensed font, and a 5 characters per line maximum.G. Lines 3 & 4 shall have a Helvetica Light Condensed font with a nominal height of 0.094 inch and a 5 characterper line maximum.



December 1, 1998

XXXXXXXXXX

0.100 ±±±± 0.015

XXX-------------XXX

2.960 ±±±± 0.006


XXX-------------XXX

XXX-------------XXX

Line 1

Line 2

Line 3

0.080 ±±±± 0.015Lucent

0.970 ±±±± 0.015

1.100 ±±±± 0.015

0.50

0 ± ±±±

0.01

5

0.38

0 ± ±±±

0.01

5

0.26

0 ± ±±±

0.01

5

0.62

0 ± ±±±

0.00

6

SHEET NOTESA. List 94 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All corners shall have a 0.06 radius.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. Lines 1, 2 & 3 shall use 8 point Helvetica Bold Condensed font and a 22 character per line maximum.



Bar

cod

e sy

mbo

lpr

int

area

(Not

e A

)

XXXXXX

0.587 ±±±± 0.006

Line 3

Line 2

Line 1

XXXXXXX

XX

XX

XX

XX

XX

1.44

9 ± ±±±

0.01

5

1.88

0 ± ±±±

0.00

6

1.70

0 ± ±±±

0.01

5

1.57

5 ± ±±±

0.01

5Lucent

0.44

5 ± ±±±

0.01

5

XXXXXXX

0.454 ±±±± 0.006

FAULT

0.03

0 ± ±±±

0.01

5

0.19

2 ± ±±±

0.01

5

SHEET NOTESA. List 95 uses Code 39 symbology (Appendix B), see Figure 21 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the "L" shall be 0.101 inch high (see 4.11).E. The nomenclature shall be "FAULT" as shown with 8 point Helvetica Light Condensed font.F. Line 1 shall have a 12 point Helvetica Bold Condensed font with a 6 character maximum.G. Line 2 shall have a 10 point Helvetica Light Condensed font with a 7 character maximum.



December 1, 1998

0.587 ±±±± 0.006

0.342 ±±±± 0.010

Line 1

Line 2

XXXXXXXX

XXXXXXXX

XXXXXXXXLine 3

2.76

0 ± ±±±

0.01

0

1.16

2

1.30

41.70

6

1.84

82.17

8

2.32

0

0.290 ±0.006

SHEET NOTESA. For certain products, List 96 is associated with the List 85 bar code label.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. Lines 1, 2 & 3 shall use 10 point Helvetica Light Condensed font with a 6 character per line maximum.



0.970 ±±±± 0.015

XX----XX Bar code symbol print area (Note A)

XX--XX XXXXXXXXXX0.40

0 ± ±±±

0.00

6

Line 1

Line 2

0.100 ±±±± 0.015

2.000 ±±±± 0.006

0.080 ±±±± 0.0150.200 ±±±± 0.015

10 point Helvetica Light Condensed, 8 characters max.

0.08 high, Helvetica Light Condensed, 5 characters max.

SHEET NOTESA. List 97 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the “L” shall be 0.101 inch high.E. Line 1 shall use a 10 point Helvetica Light Condensed font with a 8 character maximum.F. Line 2 shall use a 8 point Helvetica Light Condensed font with a 8 character maximum.



December 1, 1998

XXXXXXXXXXX

0.800 ±±±± 0.010

0.13

0 ± ±±±

0.01

5

XXXXXXXX

XXXXXXXXXXXXXXXXXXXXX

Lucent

Line 1

Line 2

Line 3

Line 4

CLEI

0.60

0 ± ±±±

0.01

5

0.48

5 ± ±±±

0.01

5

0.39

0 ± ±±±

0.01

5

0.29

5 ± ±±±

0.01

5

0.19

0 ± ±±±

0.01

5

0.05

0 ± ±±±

0.01

5

0.215 ±±±± 0.005

0.200

0.040 ±±±± 0.010

+ 0.900

0.84

0 ± ±±±

0.00

5

1.90

0 ± ±±±

0.00

6

0.75

0 ± ±±±

0.00

6

.06 Radius

Slit

0.005

SHEET NOTESA. List 99 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the “L” shall be 0.101 inch high.E. Line 1 shall use a 10 point Helvetica Bold Condensed font with a 8 character maximum.F. Line 2 shall use a 8 point Helvetica Light Condensed font with a 8 character maximum.G. Lines 3 & 4 use a 6 point Helvetica Light Condensed font with a 11 character per line maximum.H. Line 5 is the 10 character CLEI code and shall use a 7 point Helvetica Light font.



2.00

0 ± ±±±

0.01

0

Die

cut

for

labe

l sep

arat

ion 0.587 ±±±± 0.006

Bar

cod

e sy

mbo

lpr

int

area

(N

ote

A)

XXXXXXX

Lucent

XX

XX

XX

XX

XX

XXXXXXX

0.250

Line 1

Line 2

1.76

0 ± ±±±

0.01

5

1.60

0 ± ±±±

0.01

5

1.20

0 ± ±±±

0.01

5

1.10

0 ± ±±±

0.00

6

+0.040

-0.000

SHEET NOTESA. List 100 uses Code 39 symbology (Appendix B), see Figure 20 for dimensional details.B. All labels shall have a 0.06 radius on all corners.C. All dimensions are in inches, moreover this Figure is not drawn to scale.D. The Lucent Technologies logotype shall be black in color and the “L” shall be 0.101 inch high (see 4.11).E. Line 1 shall have a 10 point Helvetica Bold Condensed font with a 7 character maximum.F. Line 2 shall have a 8 point Helvetica Bold Condensed font with a 8 character maximum.



December 1, 1998

Bed with groovesto permit panelto slide freely

Wire

Clamp

Label

Bed can beRotated

To TestingMachine

Panel PerASTM D 1000

ADHESION TESTERFIGURE 66


Core3 - Inch ID

Label(See Notes)

1/8 Inch Min.(Typical)

Release Liner

A-1/64 Inch(see table)Leader

(Leading End

3 FeetMin.

AlphanumericCode

Bar Code

Roll of Labels

KS-22002 Label List Numbers

1, 2, 3, 18, 28-30, 44, 45, 49-52,59 & 60

4, 5, 10, 19, 20, 22, 23, 24, 31-36, 53,54, 56, 61, 63, 64, 72, 74-78, 88

11, 27, 65, 69, 71-73, 92

12, 13, 16, 17, 25, 26, 37-39, 42,43, 46-48, 55, 57, 58, 62, 66, 68, 70,79, 81-85 & 9014, 15, 21, 39, 40, 41, 67, 80, 86, 8789 & 91

1-1/8

2-11/64

1-5/8

2-27/32

4-7/32

Dimension “A”(In Inches)

XXXXXXXXXX- - - - - - -

SHEET NOTESA. Orientation of labels with respect to leading end of the roll shall be as shown above.B. Labels shall be centrally located along the width of release liner.C. Both the "Leader" and "Trailer" sections of release liner shall be at least 3 feet long.D. Maximum number of splices per roll of labels is 2.

BAR CODE LABEL ROLL FORM LAYOUTFIGURE 67


December 1, 1998

80 Labels Per Page

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500

Equipment Identification

XXXXXXXXXX XXXXXXXXXXXXXXXX

Text 0.18 Min. High CLEI Code

KS-22002 L47 XXXXX

XXXXXXXXXX--Sheet 1

Release Liner

6.75

0

SHEET NOTESA. Layout for Lists: 1 - 3, 6, 18, 28 - 30, 44, 45, 49 - 52, 59 & 60.B. Include only when sheet is Sheet 1 of List 6.C. All dimensions are in inches.

BAR CODE LABELS - LAYOUT SHEETFIGURE 68


Minimum of 60 LabelsPer Page

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

312

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

X

CLEI Code

10.625

6.75

0

KS-22002 L

47 XX

XX

XX

XX

XX

XX

XX

XX

XSheet 1

SHEET NOTESA. Layout for Lists: 1 - 3, 6, 18, 28 - 30, 44, 45, 49 - 52, 59, & 60.B. Include only when sheet is Sheet 1 of List 6.C. All dimensions are in inches.



December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500


XXXXXXXXXX XXXXXXXXXXXXXXXX


KS-22002 L47 XXXXX

XXXXXXXXXX--Sheet 1

10.625

6.75

0

SHEET NOTESA. Lists: 4, 5, 8 - 11, 19, 20, 22 - 24, 27, 31 - 36, 53, 54, 56, 61, 63 - 65, 69, 74, 75, 77, 88 & 92.B. All dimensions are in inches.



Minimum of 30 LabelsPer Page

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

312

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

XX

CLEI Code

10.625

6.75

0

KS-22002 L

X47 X

XX

XX

XX

XX

XX

XX

XX

XX

--

SHEET NOTESA. Lists: 4, 5, 8 - 11, 19, 20, 22 - 24, 27, 31 - 36, 53, 54, 56, 61, 63 - 65, 69, 74, 75, 77, 88 & 92B. All dimensions are in inches.



December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500


XXXXXXXXXXX XXXXXXXXXXXXXXXX


KS-22002 LX47 XXXXXXX

XXXXXXXXXX--Sheet 1

10.625

6.75

0

SHEET NOTESA. Lists: 12, 13, 16, 17, 25, 26, 37, 38, 42, 43, 46 - 48, 55, 57, 58, 62, 66, 68, 70, 72, 76, 78, 80 - 85 & 90.B. All dimensions are in inches.



1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500




KS-22002 LX47 XXXXXXX XXXXXXXXXX--

10.625

13.5

00 Minimum of 48 Labels Per PageMinimum of 0.12 Inch SeparationBetween Labels




December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500


XXXXXXXXX XXXXXXXXXXXXXXXX


KS-22002 L47 XXXXXXX XXXXXXXXXX--

10.625

6.75

0

SHEET NOTESA. Lists: 14, 15, 21, 39 - 41, 67, 86, 87, 89 & 91.B. All dimensions are in inches.



1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

13.5





December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75

0 15 Labels Per PageMinimum 0.12 InchSeparation Between Labels




1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75

0

SHEET NOTESA. Lists: 4, 5, 8 - 11, 19, 20, 22 - 24, 27, 31 - 36, 53, 54, 56, 61, 63 - 65, 69, 74, 75, 77, 88 & 92B. All dimensions are in inches.



December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75

0

SHEET NOTESA. Layout for Lists 55 & 73B. All dimensions are in inches.

BAR CODE LABEL - LAYOUT SHEETFIGURE 78


1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

5

10.625


December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75

0 35 Labels Per Page

SHEET NOTESA. List 71.B. All dimensions are in inches.

BAR CODE LABEL - LAYOUT SHEETFIGURE 80


1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75





December 1, 1998

1.000 .750 1.375 2.125 2.125 1.375 .750 1.000

7 Holes0.281 Dia.

0.37

50.

500





10.625

6.75

0

SHEET NOTESA. List 79.B. All dimensions are in inches.



APPENDIX ACODE 11 BAR CODE STRUCTURE AND WIDTHS

IN 0.001 INCH + 0.0015 (NOTE 1)

BSBSB CHARACTER BAR 1 SPACE 1 BAR 2 SPACE 2 BAR 3

00001 0 7.5 7.5 7.5 7.5 26.110001 1 16.8 7.5 7.5 7.5 16.801001 2 7.5 16.8 7.5 7.5 16.811000 3 16.8 16.8 7.5 7.5 7.500101 4 7.5 7.5 16.8 7.5 16.810100 5 16.8 7.5 16.8 7.5 7.501100 6 7.5 16.8 16.8 7.5 7.500011 7 7.5 7.5 7.5 16.8 16.810010 8 16.8 7.5 7.5 16.8 7.510000 9 26.1 7.5 7.5 7.5 7.500100 - 7.5 7.5 26.1 7.5 7.500110 (S/S) 7.5 7.5 16.8 16.8 7.5

Note 1: Dimensions may be converted to millimeters using the conversion factor 25.4.Note 2: A Start/Stop symbol precedes and follows the bar coded data.

CODE 11 CHECK DIGIT ALGORITHM

The check digit is the modulo 11 sum of weighted products where the weights from the right to left are in thesequence 1, 2, . . . . . . ., 10, 1, 2, . . . . . . . The dash character (-) is assigned to value of 10.

The calculation of the check digit is illustrated in the following example.

Given the data: 5 0 1 7 5 9 - -

Data 5 0 1 7 5 9 - -Value (V) 5 0 1 7 5 9 - -Weights (W) 8 7 6 5 4 3 2 1

To obtain the check digit calculate

C = E 1/8 (V) (W)/11 V(W)

Thus the check digit is 4 and the completed bar code should encode the character as follows:

(S/S) 5 0 1 7 5 9 - - 4 (S/S)


December 1, 1998

APPENDIX BCODE 39 BAR CODE STRUCTURE AND WIDTHSALL DIMENSIONS IN 0.001 INCH + 0.0017 INCH

Character

Bar#1 Space#1

Bar#2 Space#2

Bar#3 Space#3

Bar#4 Space#4

Bar#5

1 16.8 7.5 7.5 16.8 7.5 7.5 7.5 7.5 16.82 7.5 7.5 16.8 16.8 7.5 7.5 7.5 7.5 16.83 16.8 7.5 16.8 16.8 7.5 7.5 7.5 7.5 7.54 7.5 7.5 7.5 16.8 16.8 7.5 7.5 7.5 16.85 16.8 7.5 7.5 16.8 16.8 7.5 7.5 7.5 7.56 7.5 7.5 16.8 16.8 16.8 7.5 7.5 7.5 7.57 7.5 7.5 7.5 16.8 7.5 7.5 16.8 7.5 16.88 16.8 7.5 7.5 16.8 7.5 7.5 16.8 7.5 7.59 7.5 7.5 16.8 16.8 7.5 7.5 16.8 7.5 7.50 7.5 7.5 7.5 16.8 16.8 7.5 16.8 7.5 7.5A 16.8 7.5 7.5 7.5 7.5 16.8 7.5 7.5 16.8B 7.5 7.5 16.8 7.5 7.5 16.8 7.5 7.5 16.8C 16.8 7.5 16.8 7.5 7.5 16.8 7.5 7.5 7.5D 7.5 7.5 7.5 7.5 16.8 16.8 7.5 7.5 16.8E 16.8 7.5 7.5 7.5 16.8 16.8 7.5 7.5 7.5F 7.5 7.5 16.8 7.5 16.8 16.8 7.5 7.5 7.5G 7.5 7.5 7.5 7.5 7.5 16.8 16.8 7.5 16.8H 16.8 7.5 7.5 7.5 7.5 16.8 16.8 7.5 7.5I 7.5 7.5 16.8 7.5 7.5 16.8 16.8 7.5 7.5J 7.5 7.5 7.5 7.5 16.8 16.8 16.8 7.5 7.5K 16.8 7.5 7.5 7.5 7.5 7.5 7.5 16.8 16.8L 7.5 7.5 16.8 7.5 7.5 7.5 7.5 16.8 16.8M 16.8 7.5 16.8 7.5 7.5 7.5 7.5 16.8 7.5N 7.5 7.5 7.5 7.5 16.8 7.5 7.5 16.8 16.8O 16.8 7.5 7.5 7.5 16.8 7.5 7.5 16.8 7.5P 7.5 7.5 16.8 7.5 16.8 7.5 7.5 16.8 7.5Q 7.5 7.5 7.5 7.5 7.5 7.5 16.8 16.8 16.8R 16.8 7.5 7.5 7.5 7.5 7.5 16.8 16.8 7.5S 7.5 7.5 16.8 7.5 7.5 7.5 16.8 16.8 7.5T 7.5 7.5 7.5 7.5 16.8 7.5 16.8 16.8 7.5U 16.8 16.8 7.5 7.5 7.5 7.5 7.5 7.5 16.8V 7.5 16.8 16.8 7.5 7.5 7.5 7.5 7.5 16.8W 16.8 16.8 16.8 7.5 7.5 7.5 7.5 7.5 7.5X 7.5 16.8 7.5 7.5 16.8 7.5 7.5 7.5 16.8Y 16.8 16.8 7.5 7.5 16.8 7.5 7.5 7.5 7.5Z 7.5 16.8 16.8 7.5 16.8 7.5 7.5 7.5 7.5

7.5 16.8 7.5 7.5 7.5 7.5 16.8 7.5 16.816.8 16.8 7.5 7.5 7.5 7.5 16.8 7.5 7.5

Space 7.5 16.8 16.8 7.5 7.5 7.5 16.8 7.5 7.5*(S/S) 7.5 16.8 7.5 7.5 16.8 7.5 16.8 7.5 7.5$ 7.5 16.8 7.5 16.8 7.5 16.8 7.5 7.5 7.5/ 7.5 16.8 7.5 16.8 7.5 7.5 7.5 16.8 7.5+ 7.5 16.8 7.5 7.5 7.5 16.8 7.5 16.8 7.5% 7.5 7.5 7.5 16.8 7.5 16.8 7.5 16.8 7.5

Documents

Lucent Technologies KS-22002, Issue 24 December 1, …etler.com/docs/KS/KS-22002.pdf · Lucent Technologies KS-22002, Issue 24 Sheet 3 of 109 December 1, 1998 SHEET INDEX NUMBERS