Embed Size (px)
Citation preview
PERSONAL STORAGE SOLUTIONSX
Lockers and Cupboards
your partner in storage solutions
Deliveringthe right solution for youMoresecure lockers and cupboards are designed and manufacturedto a high specification to meet any personal storage requirements.
They are built for a long efficient working life in factories, hospitals, schools, colleges, retailoutlets - in fact anywhere needing tough, reliable and asethetic storage. Their modulardesign makes these lockers and cupboards extremely adaptable and cost effective. Units canbe specified from a wide range with a choice of locks, doors, colours and accessories,allowing lockers and cupboards to be tailored to a customers precise needs.
Our experience and expertise has enabled us to put together a proven product range,designed to conform to BS 4680 standards and manufactured in the UK to internationallyrecognised quality and environmental ISO standards. This reflects our commitment toproducing the best products whilst reducing environmental impact in the design andmanufacturing process.
Free site visit and designWe will gladly come and discuss your requirements and help you plan your lockeror cupboard needs. We will survey the room or area and produce a layout foryour approval. Installation, if required, is undertaken by our appointed fitters,who ensure your job is installed to your satisfaction with the minimum ofdisruption and mess.
Contents
Locker Features
Accessories
Full height lockers
Three-quarterheight lockers
Half height lockers
Colour Options
Door Options
Lock Options
Quarto lockers
Sixto lockers
Cube lockers
Locker RoomDesign
Utilty Lockers
Crew Lockers
Medium DutyLockers
Stronghold HeavyDuty Lockers
GarmentDispensers
Laptop Lockers
Personal ItemLockers
Post Lockers
Laminate DoorLockers
Wooden DoorLockers
AluminiumLaminate DoorLockers
Seating andBenching
Security & StandardCupboards
Slim, Large Volume,Vision and StorageCupboards
Tool Cabinets
HazardousSubstanceCupboards
12
10
9
345
16
17
18
19
20
21
22
23
15
13
14
page 3
l Our standard duty lockers have been tested and conform to the requirements of the British Standard for Clothes Lockers BS 4680: 1996 ‘Standard Duty’.
Robust Design
l All doors have an all-round reinforcing edge.
l A welded vertical channel section stiffens the door for protection against impact damage.
l Steel three-knuckle hinges are welded to the door and riveted to the frame to give added strength and allow for easy replacement of damaged doors.
l Complying with BS 4680, a close fit between the door and the frame of less than 2mm protects against leverage in attempted forced entry.
l Colours are applied electro-staticallyas an epoxy-polyester powder coat, then baked to provide a high quality, durable finish.
Integral Security
Lockingl Features in-frame locking through
the door with a hooked cam engaging into the frame.
lThis provides extra security by significantly increasing resistance toforced entry.
Anti-theft shelfl The design of the intermediate
shelf prevents access to compartments above and below an open door.
Lock platel The lock cover plate and handle
provides recesses to accept compartment numbering or identification.
Proven Products
BS 4680 - the standard for clothes lockers BioCote ® - bacteria locked outl BioCote® antimicrobial technology is incorporated into all
Moresecure lockers and cupboards at the time of manufacture, offering constant protection against a wide range of bacteria.
l Field tests prove that storage equipment treated with BioCote®
powder coating benefits from a 94% reduction in bacteria on their surface, helping create a cleaner and more hygienic working environment.
Locker support frames and seat unitsraise lockers off the floor, reducingimpact damage and making cleaningeasier. Support frames aremanufactured from 25mm square steeltube in a welded construction and arepainted light grey as standard tomatch the lockers. Standard height is150mm, and widths and depths aredesigned to match the lockerinstallation.
Seat units are incorporated into thelocker frame as well as slatted seats tothe front. They can include a meshshelf for footwear. Standard height is400mm to match freestanding benchseating units.
Sloping tops are essential in hygiene-sensitive locations such as hospitalsand the food industry. The 22 degreeslope prevents litter being left onlocker tops and makes cleaning easier.
Sloping Tops for lockers
Locker Depth300380450500550600
Top Height125158187207228240
Dimensions mm
Support Frame
Support Frame with seat
Bridge Unit forModular Lockers
Bridge Unit TopThis is fitted to adjacent lockerswith nuts & bolts supplied.Incorporates a central full-lengthhanging rail with the option of‘captive’ clothes hangers whichcannot be removed, therebypreventing theft and accidental loss.
Bridge Unit BaseA free-standing rack to supportfootwear or other items 150mmabove the floor.
Widths mm600900
1200
Depths mm300450500550
Height - 60mm
Accessories for tailored solutions
page 4
Widths mm225300380450
Depths mm300380450500550600
Height - 1800mm
Full Height
Internal fittings:
l One intermediate fixed shelf.
l Each compartment has a fixed garment hanging rail (except for 300mm deep).
l Each compartment has two coat hooks.
Two-Door
Colours and Finishes
page 5
Internal fittings:
l Fixed top shelf.
l Fixed garment hanging rail (except 300mm deep).
l Two coat hooks.
Single-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 1800mm
Mild Steel Modular
Vision Door
Incorporates atoughenedpolycarbonate viewpanel set within asteel door with anall-roundstrengthened edge -allows you to seeitems stored inlockercompartmentswithoutcompromisingsecurity.
Perforated Door
Particularly usefulwhere damp clothesand odours pose aproblem.
Door OptionsYou can choose from a variety ofdoor styles to tailor the locker toyour specific situation.
Standard Duty Door
This flat mild steeldoor fits flush withinthe door frame – lessthan 2mm betweendoor and frame (forcompliance withBS 4680) to protectagainst leverage inattempted forcedentry.
Pastel Door Colours
Light Grey (RAL 7035)
Light Grey (RAL 7035) Red (RAL 3020)
Blue (RAL 5002) Green (RAL 6001)
Carmine Red (RAL 3002) Yellow (RAL 1003)
Dark Grey (BS 00A11) Burgundy (RAL 3003)
Electric Blue (BS 20 E 51)Black (RAL 9005)
Sunburst Yellow (BS 10 E 50) Candy Pink (BS 02 C33)
Light Violet (BS 381 C 797) Turquoise (RAL 6034)
Standard Door Colours
Note: due to the limitations of matching painted steel to theprinting process, colours illustrated on this page offer a good,but approximate guide. For exact colour reference, paintedsteel samples are available upon request.
Standard Body colour is Light Grey (RAL 7035)
Epoxy-polyester powder coat colours with BioCote® protection.
BioCote® Paint Finish
LockOptions
Standard Deadlock
This simple and economicalcam lock provides useraccess with a small, easilyreplaced key. The lock issupplied with two keys anda master key is available.
Hasp & Staple Padlock Fitting
Transfers responsibilty forlocking to the user. The user isrequired to secure the lockerwith a padlock (not supplied).This system provides flexibilityat the loss of some control overallocation of lockers.
Internal fittings:
l Two intermediate fixed shelves.
Internal fittings:
l Three intermediate fixed shelves.
Internal fittings:
l Four intermediate fixed shelves.
Internal fittings:
l Five intermediate fixed shelves.
Widths mm225380450
Depths mm300380450500
Height - 1800mm
Six-DoorThree-Door Four-Door Five-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 1800mm
Widths mm225300380450
Depths mm300380450500550600
Height - 1800mm
Widths mm225300380450
Depths mm300380450500550600
Height - 1800mm
lockers for maximum versatility
Insight Door
These shatterproofpolycarbonatedoors allow100% visibilitywhile maintainingthe highest levelof security.
page 6
Coin/Token Return Lock
Ideal when lockers have‘shared’ users. The key isreleased when coin (£/€) ortoken is inserted. Key is captiveagain when the door isreopened and the coin/token isreturned to the user.
3 Tumbler Combination Lock
Ideal for facilities where keysare not desirable. The user setsa code holding the button onthe right hand side of the lock.On release of the button thecode is set. The code can bechanged at any time when thelock is open.
Digital Combination Lock
Simple-to-use, battery-operatedkeyless lock. Can beprogrammed for dedicatedsingle-user or multi-user ‘openaccess’ mode. Personal entrycode can be set and changed,whilst a master keyensures supervisor access.
Multi-user Combination Lock
Ideal for facilities where keys arenot desirable. The lock can bereset whenever it is open. Thisallows the locker to be used byseveral people at different timesthroughout the day, reducing thenumber of locker compartmentsrequired and the need for keys.
Magnetic Catch Lock
For use in Primary schools orenvironments where risk of keyloss is high and security minimal.Offers positive closure of the door.
Coin/Token Retain Lock
Generates revenue from‘shared’ user lockers. The keyis released when coin (£/€)or token is inserted. Key iscaptive again when the dooris reopened. Coin/token isretained in the box.
Three Quarter Height Half Height
Internal fittings:
l One intermediate fixed shelf.
Internal fittings:
l Compartment has a fixed garment hanging rail with two coat hooks.
Internal fittings:
l Compartment has a fixed garment hanging rail with two coat hooks.
Internal fittings:
l Two intermediate fixed shelves.
Three-DoorSingle-Door Two-Door Single-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 1382mm
Widths mm225300380450
Depths mm300380450500550600
Height - 1382mm
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
page 7
Coin/Token Return Lock
Ideal when lockers have‘shared’ users. The key isreleased when coin (£/€) ortoken is inserted. Key is captiveagain when the door isreopened and the coin/token isreturned to the user.
3 Tumbler Combination Lock
Ideal for facilities where keysare not desirable. The user setsa code holding the button onthe right hand side of the lock.On release of the button thecode is set. The code can bechanged at any time when thelock is open.
Digital Combination Lock
Simple-to-use, battery-operatedkeyless lock. Can beprogrammed for dedicatedsingle-user or multi-user ‘openaccess’ mode. Personal entrycode can be set and changed,whilst a master key ensuressupervisor access.
Multi-user Combination Lock
Ideal for facilities where keys arenot desirable. The lock can bereset whenever it is open. Thisallows the locker to be used byseveral people at different timesthroughout the day, reducing thenumber of locker compartmentsrequired and the need for keys.
Magnetic Catch Lock
For use in Primary schools orenvironments where risk of keyloss is high and security minimal.Offers positive closure of the door.
Coin/Token Retain Lock
Generates revenue from‘shared’ user lockers. The keyis released when coin (£/€)or token is inserted. Key iscaptive again when the dooris reopened. Coin/token isretained in the box.
Three Quarter Height Half Height
Internal fittings:
l One intermediate fixed shelf.
Internal fittings:
l Compartment has a fixed garment hanging rail with two coat hooks.
Internal fittings:
l Compartment has a fixed garment hanging rail with two coat hooks.
Internal fittings:
l Two intermediate fixed shelves.
Three-DoorSingle-Door Two-Door Single-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 1382mm
Widths mm225300380450
Depths mm300380450500550600
Height - 1382mm
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
page 7
Internal fittings:
l One intermediate fixed shelf.
Two-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
Internal fittings:
l Two intermediate fixed shelves.
Three-Door
Widths mm225300380450
Depths mm300380450500550600
Height - 900mm
Quarto Sixto Cube
Widths mm225300380450
Depths mm300380450500550
Height - 511mm
Widths mm225300380450
Depths mm300380450500550
Height - 372mm
Widths mm300380450
Depths mm300380450
Heights - 300, 380or 450mm
Small Modular lockers
Quarto and Sixto lockers can be stacked, theirmodular design also allowing them to be used withstandard lockers
Full height lockers with Sixtolockers for additional under-seatstorage.
Quarto and Sixto lockers can befitted on top of lockers to increaseavailable storage height withadditional compartments.
Cube lockers are ideal for stacking, creatingbanks of individual compartments.
page 8
Cubes - as the namesuggests - have an equalheight, width and depthallowing combinedstacking of units on thefloor or on supportframes.
page 9
Locker Room Design
Lockers are supplied as nested units - lockers of the same overall dimensions,sharing common side panels, manufactured and supplied fitted together.
This saves on the steel used, giving you the most economical solution.
Locker Nesting
Features of the locker room Requirements for usage
Initial lockerNest of 1
Nest of 2 lockers Nest of 3 lockers
The size, location, fixtures & fittings of the area or room designated for thelockers will affect the positioning and layout of the lockers. Take intoaccount the following:
l Is the room or area large enough to accommodate the number (and size) of lockers required, whilst still leaving enough space for users to have easy access?
Note: ensure that the space is not confined, making the lockers awkward or uncomfortable to use, and the room potentially hazardous in an emergency evacuation situation (in response to a fire alarm, for example).
l Is the room or area accessible to groups of people who may all arrive at one time? Are any adjacent corridors, stairs or lifts easy to get to and move through? Is the room readily accessible for delivery and installation of the lockers?
l Take into account the position of doors and windows and their effect on the locker layout.
Note: the position of fixtures and fittings which could either obstruct the lockers or be obstructed by them. For example: ceiling pillars, low ceilings, alcoves, beams, skirting boards, radiators & heating pipes, light switches, sockets and other power outlets, lighting fixtures, ventilators and air-conditioning units, any access to service points.
l Check the condition of the floor - What is it made of? Is the surface suitable and in good condition? Is it level: lockers should always be located on a level, even floor. If there is significant slope, consider locating the lockers on support frames with adjustable feet .
l How are the floors cleaned? Even in a generally ‘dry’ changing area, the floor may be washed or mopped down from time to time. Where floors may be left damp for some time and on a regular basis, consider raising the lockers from the floor on a support frame which has a protective finish against corrosion.
l Assess the lighting - ill-lit locker rooms can appear oppressive and unwelcoming. Carefully assess the positioning of lockers and their effect on lighting - avoid creating areas of dark or shadow in the room, particularly in corners. If there is natural light, make the best use of it. How is the artificial light provided? Will it conflict with the locker layout? If so, can the lighting be altered or the locker layout changed?
Consider the following at the initial planning stage:
l How many people in all have a requirement for a locker?
l Do people require their own personal locker or can the lockers be shared? - for example, to cater for shift workers
l When will the lockers be used? - are they required on a regular daily basis, or infrequently?
l Accessibility: what would be the maximum number of people requiring access to the lockers at any one time? - is additional space required to prevent overcrowding at ‘peak times’ - during the the changeover of work shifts, for example
l What kinds of items of clothing, equipment, personal possessions or carrying bags will users bring into the locker room? This will help determine the size of compartment/s required and also the locker and floor spacing - for example, where bulky clothing or equipment is involved, more floor space may be necessary for ease of movement
l What kind of access and ‘ownership’ is required for the lockers? This will influence the type of lock used: where an individual has their own locker, a cam-lock or padlock can be fitted, operated by the owner’s key; where lockers are for shared use, coin or token-operated locks may be preferred as easier to administer
l What degree of privacy is appropriate? - people may need to change their clothes, in part or in full
l Is there a requirement for seating?
l Is there a requirement for ‘shared’ clothes hanging facilities within the locker room?
Overall DimensionsWhen planning a locker room layout, allowance should also be made forthe incremental increase in the overall length of locker runs, where nestedunits are butted together. 2mm is added to the overall length at each point where two nested unitsjoin together (refer to example illustrated, below).
Locker Nesting - overall run length dimension (plan view)
Nest of 3 Nest of 3 Nest of 3 Nest of 3 Nest of 3
+ 2mm + 2mm + 2mm + 2mm
Example: run of 15 locker units, 300mm wide, in 5 nests of 3. Overall run length calculation:5 x 900mm + 8mm (4 x 2mm, nested units join at 4 points) = 4508mm overall
Locker Run SpacingLockers standing on the floor should be positioned so that there is a clearspace or aisle at least 900mm wide - but preferably 1000mm - between thelocker fronts and the opposing fixture - this could be a parallel run oflockers, or a corridor wall. Always allow clearance for wide-open doors - thisvaries according to the locker width.Where space is available, the width of the aisle can be increased up to1500mm where facing lockers are likely to be used simultaneously.
900mm min up to 1500mm
Lockers standing on support frames fitted with a seat should have aminimum aisle width of 900-1000mm between seats, but a spacing of1200mm is desirable if facing lockers are to be used simultaneously.
Internal fittings:
l Users have a three quarter length compartment with a separate full width compartment opened with the same key.l Hanging compartment has two coat hooks.
Width mm450
Depth mm450
Height - 1800mm
Internal fittings:
l Fixed top shelf.l Central divider.l Both divided compartments have a garment hanging rail and coat hook.
Width mm450
Depth mm450
Height - 1800mm
Clean & Dirty LockerInternal fittings:
l Fixed top shelf.l Central divider.l Hanging rail and hook.l Three fixed shelves.
Width mm450
Depth mm450
Height - 1800mm
Uniform Locker
Utility
Two Person Locker
Utility Lockers
page10
We also offer a variety ofPolice locker solutions. Fromthe storage of ‘Airwave’radios to PSU bags we havethe right solution for Policeforces throughout the UK.
Police
Width mm450600
Depth mm600600
Height - 1800mm
l Also available sloping tops, see page 4.l Choice of door colours, see page 5.l Fitted with Deadlock as standard. Optional locks, see page 6 for details.
Crew
Internal fittings:
l Fixed heavy-duty top shelf.l The hanging compartment has a heavy duty hanging rail.
Two compartmentInternal fittings:
l Fixed heavy duty top and lower shelves.l Divided compartments. l Heavy duty hanging rail.
Four compartmentInternal fittings:
l Top shelf, divided compartment below, with one fixed shelf and hanging rail to either side.
Width mm380
Depth mm450
Height - 1800mm
Work Wear Locker
Police Lockerwith:l Airwaves compartmentl CS Cannister holder
Police Lockerwith:l Lockable cube on door with clear perspex front
Police Lockerwith:l CS Cannister holder
Width mm600
Depth mm600
Height - 1800mm
page 11
Width mm450600
Depth mm600600
Height - 1800mm
Enhancing the already robustdesign of the Standard Dutysteel locker, the uprated mediumduty versions have an additionalvertical reinforcement channeland a shielded front of double-gauge steel for triple thicknessprotection.
This toughened design providesadditional defence against thetwin problems of vandalism andtheft.
Inner reinforcingchannel to standardduty specification
Outer reinforcing channelto medium dutyspecification
Double-gauge shielding
l Second channel section welded to the inside of the door to provide triple thickness strength.l This significantly increases the reinforced area of the door's width and height and makes the door extremely difficult to deform, providing additional protection against forced entry.l The form of the of the channel is extended across both sides of the door it doubles the gauge of the steel to resist impact damage.l Also available sloping tops, see page 4.l Choice of door colours, see page 5.l Fitted with Deadlock as standard. Optional locks, see page 6 for details.
page 12
Medium Duty Lockers
Widths mm300380450
Depths mm300380450500550600
Height - 1800mm
The medium duty design raises thestandard duty ranges to a higherlevel of protection.
Combining robust design with a heavy gauge‘double skin’ door to guard against leverage andimpact, Stronghold lockers are hard to beat whenit comes to long-lasting security.
Strengthened doorconstructed fromheavy gauge steelreinforced at top andbase
Right-angled doorflangeto guardagainstleverage
Additionalbox-section
Wrap-around securesection located behind thefull length of the door framewhen closed, protectingagainst forced entry
Tough paintfinish protectsand resistscorrosion andwear. Pre-phosphated,then powdercoated
l Heavy-duty 5-knuckle hinge welded to the door, but rivetted to the frame to allow for easy replacement.l Single compartment lockers, fitted with hat shelf and hanging rail with double coat hook as standard.l Two compartment lockers have double coat hook in each compartment.l Choice of door colours, see page 5.l Fitted with Deadlock as standard. Optional locks. Hasp & staple fitting (for use with own padlock). Coin/token operated locks. See page 6 for details.
page 13
Single Door
Two Door Three Door Four Door Six Door
Width mm305
Depths mm305457
Height - 1778mm
Stronghold Heavy Duty Lockers
page 14
10-Door Dispenser15-Door Dispenser
Designed initially for work wear, these lockersare equally suitable for the controlled issue ofsafety equipment, consumables or specificmaterials required for a working day or shift.
Individual Access
Garment issue lockers provide each workerwith key access to their secure compartment tocollect a freshly laundered issue of clothing.Compartment doors are inset within the mainfull-height door, which remains locked.
Convenient Re-supply
The full-height main door allows access to allof the individual compartments for re-stockingwith laundered clothing.
Laundry Collection
Workers ‘post’ their used garments into anadjacent Collection locker. These arecollected in a laundry bag (not suppliedwith lockers). This separation of cleanand used items can make a majorcontribution to maintaining ahygienic working environment.
The managed issue of workplace clothing - often via thirdparty laundries - is an essential part of hygiene procedure inmany sectors. Integral BioCote protection (see page 3) onall our garment issue lockers provides a valuable additionalbenefit to these industries.
5-Door Collector &Dispenser
l Half-height upper ‘issue’ doorwith 5 compartments.
l Lower ‘collector’ door with ‘post slot’.
l Hooks for laundry collection sack (sack not included).
Width mm381
Depth mm457
Height - 1778mm
Garment Dispensers and Collectors
5-Door Dispenser 20-Door Dispenser
l Also available sloping tops, see page 4.l Choice of door colours, see page 5.l Fitted with Deadlock, with 2 keys.
Collector
l Full-height door.
l Galvanised anti-theft shelf, angled inside ‘post slot’.
l Hooks for laundry collection sack (sack not included).
l 15 compartment locker has each door reinforced fitted with its own key-operated cam lock (‘dead locking’).l Single door locker version allows access to all compartments under one key.l 15 compartment lockers accept laptops WITHOUT carry cases.l Laptop lockers are available with optional hardwiring for power and networking, allowing computers to be recharged while being stored.l Also available sloping tops, see page 4.l Choice of door colours, see page 5.l Fitted with Deadlock as standard. Optional locks. Hasp & staple fitting (for use with own padlock) Digital combination lock (4 door only). Coin return lock (4 door only). See page 6 for details.
Fifteen-Door LockerCompartment sizel 90h x 285w x 425d mm
Single-Door LockerCompartment sizel 90h x 285w x 425d mm
Width mm381
Depth mm457
Height - 1778mm
Width mm381
Depth mm457
Height - 1778mm
These purpose-designed locker unitsprovide a safe sanctuary for laptops andreal peace of mind for users.
Personal item lockers provide secure storage forsmall but valuable possessions in public areasand throughout the working environment.
Perforated Door Plain Door
Also available, optional factoryfitted, full-height protective steel channel kit to cover all locks. Requires padlock.
Width mm250
Depth mm155
Height - 915mm*
Personal Item Lockers
l Allows sorted mail to be posted into secure compartments which are opened on the recipients key.l 10 or 15 tier lockers.l Individual doors are set within a main door, which is opened on its own key giving access to all of the interior.l Choice of door colours, see page 5.l Fitted with Deadlock, with 2 keys.
Post Lockers
Laptop Lockers
*Height rises to 975mmwith sloping top.
page 15
Width mm381
Depth mm457
Height - 1800mm
l Choose from 4 or 8 doors in nests of 1 or 2.l Units can be hung on walls, fitted on top of each other or side to side.l Choice of door colours, see page 5.l Fitted with Deadlock as standard. Optional locks. Hasp & staple fitting (for use with own padlock). Digital combination lock (4 door only). Coin return lock (4 door only). See page 6 for details.
page 16
Laminate Door Lockers
Combines the versatility of steel lockers with thedurability of solid grade laminate doors.
Four Door Locker with InsetDoorsInset doors provide a visual contrastbetween the door finish and thelocker frame.
Robust hinge designThe door is clamped between integral securityplate and the 5 knuckle hinge and thenrivetted to the frame.
Door numberingDoors feature apre-drilled recess readyto accept a numberingdisc. Number discsavailable seperately.
Plain door versionavailable on request.
Three Door Lockerwith Plant-on DoorsPlant-on doors cover thefront face of the lockercarcase creating a wall ofcolour.
l Solid grade laminate material offers a robust, elegant solution with a range of colours and material designs, to satisfy all requirements.l Choice of door styles.l Choice 2, 3 or 4 door as standard, other door configurations on request.l Various locking options available: Standard deadlock. Digital combination lock. Padlock fitting. Coin/token operated locks.l Optional sloping tops to improve hygiene.l Support frames, stands and bench seating also available.
Depths mm300380450500
Height - 1800mm
Widths mm300380
Wooden Door Lockerscombine the strength anddurability of steel lockers withthe aesthetic appearance ofwooden lockers.
Wooden door lockers provide aneconomical alternative to all woodenfacilities, providing a clean, professionalfinished line presenting an all wood front.Matching end panels ensure the finishedinstallation has a quality ‘all wood’ effect.
l Attractive profiled doors.l Concealed self closing hinges.l Fitted with Deadlock as standard. Optional locks. Digital combination lock. Padlock fitting. Coin/token operated locks. See page 6 for details.
Wooden Door Lockers
Width mm300380
Depths mm450
Height - 1800mm
Internal fittings:
l Three intermediate fixed shelves.
Four-DoorInternal fittings:
l One intermediate fixed shelf.
l Each compartment has a fixed garment hanging rail.
l Each compartment has two coat hooks.
Two-DoorInternal fittings:
l Fixed top shelf.
l Fixed garment hanging rail (except 300mm deep).
l Two coat hooks.
Single-Door
page 17
MFC Wood Grain Finishes
Beech Light Oak Birch
Maple Ash Cherry
Apple Walnut
White Banyan Black Banyan
Wood Grain Finish
Granite Caviar
Other
White
Blue
Yellow
Light Green
Green
Pearl Grey
Speckled Rose
Red
Light Blue Purple
As standard we providelaminate doors using thefollowing colours.
Standard SolidGrade Laminate
SpeckledWhite
SpeckledPearl Grey
SpeckledLight Green
Speckled Blue
Flat Door Finish
Speckled Door Finish
page 18
Withstanding humid atmospheres, theselockers have a superb finish to suit anyarchitectural design.
l Lockers have clean lines and continuous colour across the changing area. l 1800mm lockers available as 1, 2, 4 or 2 door above 2 quarter height doors and visa versa.l 900mm high lockers available as 1 or 2 doors.l Concealed hinges bolted to doors and frames.l Single-piece body for easy internal cleaning and snag-free storage of clothes and personal belongings.l Robust aluminium shelves riveted through the body for additional strength. l 95O custom-designed hinge.l Maximum clear access into locker width due to the compact design of frame uprights.l Gentle integral return spring on doors to avoid trapping hands or fingers; Doors have rounded, bull nose safe edges.l Integral double coat hook and hanging rail.l Choice of finishes, see page 17.l Fitted with Deadlock as standard. Optional locks. Digital combination lock. Coin/token operated locks. See page 6 for details.
Lockers are designed to provide cost-effective ‘wet-area’ personal storagesolutions in leisure and sports facilities.
Widths mm300380
Depths mm450500
Height - 900 or 1800mm
Aluminium Laminate Door Lockers
Seat units are incorporated intothe locker frame as well as slattedseats to the front. They can alsoinclude a mesh shelf for footwear.Seats are a standard depth of 300,400 or 450mm and standard heightis 400mm to match freestandingbench seating units.
Support Frame with Seat
Bench seating and accessories
An essential element of all changing facilities, our bench andseating range is available to meet all your needs from mild orstainless steel frames to solid wood, composite or solid gradelaminate slats.
You can choose from:
l Free-standing benches
l Wall-mounted back rest and clothes hook boards
l Single or double-sided free standing seat units with back rest & hook board
l Cantilever wall bench
l Locker support frames with integral seating
page 19
Seating & Benching
Cupboards meet the stringent requirements ofBS EN 14073:2004 (Parts 1, 2 & 3) and BS EN14074:2004. Cupboards feature:
l Door vertical stiffening for added strength l Adjustable shelves on a 25mm vertical pitchl Shelves carry a maximum of 78kg UDLl Choice of door colours, see page 5
Handle designed for easieroperation, allows door closingwithout the key
Three point locking as standard
Where valuable and potentially vulnerable materials or equipment are usedin the workplace, the need for storage equipment with enhanced securitybecomes a necessity. Security cupboards benefit from an additional hasp and staple fitting for use with a padlock (not supplied) as well as the standard 3 point locking.
Internal LayoutsStandard, Security, Slimline, LargeVolume and Vision cupboards are allavailable in the internal configurationsshown right. These offer a range ofsolutions to meet the need for securestorage around the workplace.
A versatile and robust range ofsteel cupboards providing securestorage in the workplace.
page 20
Width mm915
Depth mm505
Height - 984 or 1820mm
Security Cupboards
Width mm915
Depth mm505
Height - 984 or 1820mm
Standard Cupboards
S12S12 S13 S14
S00 S01 S02
With the same all-steel design and features of standard cupboards,Slimlines are available with various internal configurations.
l Door vertical stiffening for added strength l Adjustable shelves on a 25mm vertical pitchl Shelves carry a maximum of 78kg UDLl Choice of door colours, see page 5
The practical solution where storage space is limitedSlimline cupboards provide secure storage in a compact‘footprint’.
Large Volume Cupboards are available with various internal configurationsand feature the following
l Semi-concealed hingesl Magnetic door catchesl Door vertical stiffening for added strength l High quality lock operating 3-point locking bars l Shelves supported on clips, height adjustable on 25mm incrementsl Robust, all-steel constructionl Choice of door colours, see page 5
Spacious storage of larger items in the workplace
Slimline Cupboards
Large Volume Cupboards
page 21
Width mm615
Depth mm505
Height -1820mm
Width mm1220
Depth mm457
Height -1829mm
Large Volume Cupboards have ahigh quality metal lock operationthe 3 point locing system
S20 S21 S22 S25
S08 S09 S10 S11
Lockers provide visible but secure storagesuitable for most working environments tostore tools, computer periperals, electroniccomponents and high value items.
Vision Cupboards
Based on the standard all-steel cupboards, with the additionof toughened polycarbonate view panels set within a steeldoor which has an all-round strengthened edge.l Semi-concealed hingesl Magnetic door catchesl High quality lock operating 3-point locking bars l Shelves supported on clips, height adjustable on
25mm incrementsl Robust, all-steel constructionl Choice of door colours, see page 5
Width mm915
Depth mm505
Height - 1820mm
Width mm915
Depth mm505
Height - 984mm
Storage Cupboards
Width mm915
Depth mm505
Height - 984mm
Width mm450
Depth mm300
Height - 684mm
l Ronis deadlock operating single point locking
l 1 adjustable shelf
l 3 point lockingl 2 adjustable shelves
Width mm480
Depth mm505
Height - 984mm
l 3 point lockingl 2 adjustable shelves
A useful range of smaller, practically sizedlow cupboards designed for generalstorage uses.
l Door vertical stiffening for added strength l Adjustable shelves on a 25mm vertical pitchl Shelves carry a maximum of 78kg UDLl Choice of BioCote door colours,
see page 5
page 21
Handle designed for easieroperation, allows doorclosing without the key.
Versatile tool cabinets in four overall sizes with variouscombinations of painted drawers and galvanised shelves.
All cabinets feature a secure barrel lock, operating a 3-point locking system.
l Door has vertical stiffening for added strength.l Choice of door colours, see page 5.
Tool Cabinets
page 22
Width mm915
Depth mm505
Height - 1820mm
Width mm915
Depth mm505
Height - 984mm
l 2 drawers, 2 shelvesC1661TGU--29S35
l 7 drawers, 1 shelfC1661TGU--29S41
l 4 shelvesC1661TGU--29S31
l 6 drawers, 6 shelvesC1961TGU--29S40
l 8 shelvesC1961TGU--29S32
l 4 drawers, 4 shelvesC1961TGU--29S38
l 14 drawers, 2 shelvesC1961TGU--29S44
l 1 drawer, 1 shelfCH661TGU--29S33
l 1 drawer, 2 shelvesCH661TGU--29S34
l 2 drawers, 1 shelfCH661TGU--29S45
l 2 shelvesCH661TGU--29S30
l 6 drawersCH661TGU--29S39
l 8 drawersCH661TGU--29S42
l 4 drawers, 1shelfCH961TGU--29S37
l 2 drawers, 4 shelvesCH961TGU--29S36
l 8 drawers, 2 shelvesCH961TGU--29S43
Width mm480
Depth mm505
Height - 984mmWidth mm
480Depth mm
505
Height - 1820mm
Extension drawers 90mm high with 25kgload capacity (evenly distributed). Safetystop allows extension up to 80%. Height adjustable in 25mm increments.
Rubber mat fitted to topof all low cabinets.
Optional desk unit isavailable for low singlecabinets.
Mobile chassis for use withlow cabinets.
Shelves adjustable in 25mm increments.Safety stop allows extension up to 80%.
page 23
Hazardous substances should be locked away in a secure facilitywhen not in use. Moresecure’s substantial range of storage cabinetsmeet the regulatory requirements surrounding use of these materials.
HazardousSubstance Cupboards
Width mm915
Depth mm355
Height - 790mm
l One shelfl Three-point locking
HA931HYDYD29S11
Width mm300
Depth mm300
Height - 770mm
l One shelfl Single-point camlock
HA221HYDYD00S11
Width mm450
Depth mm300
Height - 770mm
l One shelfl Single-point camlock
HA521HYDYD00S11
Width mm450
Depth mm450
Height - 770mm
l One shelfl Single-point camlock
HA551HYDYD00S11
Width mm450
Depth mm300
Height - 595mm
l Single-point camlock with no shelf
HQ521HYDYD00S00
Width mm477
Depth mm505
Height - 1905mm
l Three shelvesl Three-point locking
H1661HYDYD29S13
Width mm915
Depth mm505
Height - 1905mm
l Three shelvesl Three-point locking
H1961HYDYD29S13
Width mm477
Depth mm505
Height - 1070mm
l One shelfl Three-point locking
HH661HYDYD29S11
Width mm915
Depth mm505
Height - 1070mm
l Two shelvesl Three-point locking
HH961HYDYD29S12
Width mm915
Depth mm505
Height - 790mm
l One shelfl Three-point locking
HA961HYDYD29S11
Supplied with three high visibilitylabels. Simply choose the rightlabel for the type of substancebeing stored:
l Harmful materials.
l Highly flammable.
l Corrosive materials.
Labels are approved to the newHSE regulations and guidelines.
l Designed to provide safe and secure storage of chemicals, paints and hazardous substances as defined by CoSHH guidelines.
l Independently assessed to conform to HSG51 and SR24.
l All steel construction for long life with low maintenance.
All hazardous substance storage cupboards have the following key features;
l All units 790mm and above feature 3-point locking for additional security of the contents.
l Flush fitting handle for easier operation, eliminates risk of snagging when handling potentially hazardous substances.
l Door can be closed without the key being inserted on all 790mm plus units.
l Flush fitting handle for smaller cupboards under 770mm with Camlock as standard.
l Adjustable shelves to maximise space for stored material.
l Reinforced doors for added security.
l Fully welded integral sump to eliminate leakage and contain spillages up to 35ltrs (approx).
l Powder-coated paint finish with BioCote® protection for reduced risk of cross contamination.
In the event of spillage within the cupboard, it is recommended the sump isinitially emptied by means of an appropriate pump and the contents disposedof correctly in accordance with the relevant waste management regulations.
Independently Assessed to HSG51 and SR24
of the Health and Safety at Work legislation.
For further information on Moresecure products, please contact your local distributor:
Pallet racking Two-tier shelving Heavy duty shelving
Mobile shelving Mezzanine floors Industrial shelving
Stockroom shelving Small parts storage Square tube
