Upload
truongnhi
View
219
Download
0
Embed Size (px)
Citation preview
125 Industrial Drive | Spearfish, SD 57783 | Toll Free 888.3WHEELS w w w . l e h m a n t r i k e s . c o m
2013+ Honda GL1800 F6B MODELS
Limited Lean Suspension Installation Instructions
Oct, 2014
2
• Safety Information • Specifications • Disassembly • Tour Box Frame Modification • Fender Modification • Driveline and Suspension Disassembly • Brake System Modification • Reverse Module Mounting • Swingarm Installation • Differential and Suspension Installation • Driveshaft Installation • Brake System • Amplifier Installation • Sway Bar Installation • Park Brake Installation • Trunk Latch • Body Preparation • Door Installation • Body Installation • Exhaust Installation • TPMS Disable • ABS Disable (If Applicable)
© 2010. All rights reserved. Lehman Trikes® provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Lehman Trikes® assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Lehman Trikes® reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Lehman Trikes® is a registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America.
SECTION BREAKOUT
3
UNDERSTANDING SAFETY LABELS & INSTRUCTIONS
READ AND BECOME FAMILIAR WITH ALL WARNING, CAUTION SYMBOLS AND STATEMENTS
LISTED BELOW AND IN THE TEXT OF THIS MANUAL BEFORE YOU BEGIN WORK.
DANGER, WARNINGS & CAUTION SYMBOLS
This is the safety alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Your safety is involved!
SAFETY ALERT WARNING indicates a potential hazard that may result in severe injury or death to the operator, by-stander or person (s) inspecting or servicing the vehicle.
WARNING
Indicates a potential hazard that may result in minor per-sonal injury or damage to the vehicle.
CAUTION
CAUTION indicates special precautions that must be taken to avoid vehicle damage or property damage.
CAUTION
NOTE provides key information by clarifying instructions.
NOTE:
IMPORTANT provides key reminders during disassembly, assembly and inspection of components.
IMPORTANT:
SAFETY INFORMATION
4
General Safety Information This kit is designed to be installed by a competent technician. Improper installation can affect the safe operation of your trike, which could also result in serious injury or death. Make sure you have a complete understanding of the work to be preformed. Unqualified installers are urged to have the unit installed by a trained technician.
• Always protect yourself when the vehicle is in the air. Make sure the vehicle is properly supported anytime you use a hoist or jack.
• Always use the proper tools.
• Protect your eyes by using proper safety glasses or goggles.
• Read through the installation instructions before you begin. Make sure you have all the proper tools, parts and skill set to perform the installation safely and completely.
SAFETY INFORMATION
WARNING
5
Specifications • Verify that you have all components before assembly.
• Before installing your new Lehman kit, we recommend that your motorcycle be inspected and serviced by a qualified technician. Replace any worn or damaged parts before installing the trike kit.
INFORMATION
Overall Width 57.75" Overall Length 112" Wheel Base 72" Curb Weight 1204lb Rear Tire Size 205/70‐15 Rear Tire Pressure 26 PSI Rear Suspension Double A‐Arm Independent Rear Gear Ratio 2.93 Storage 6 Cubic feet
6
Disassembly NOTE: Refer to Honda service manual for de-tailed instructions on removal of OEM parts. 1. Load motorcycle on lift and secure front wheel. 2. Place motorcycle on center stand. 3. See Fig. 1. Remove LH/RH grab handles with
6mm Allen socket. Save grab handles and hardware.
4. See Fig. 2. Remove seat with 8mm socket. Save all seat mounting hardware.
5. See Fig. 2. Remove and save (2) rubber grom-mets from seat shell.
6. See. Fig. 3. Remove rear trim from seat shell. 7. See. Fig. 3. Remove rear light assembly.
Light mounting hardware is located inside LH/RH saddlebags.
PREPARING THE MOTORCYCLE
Fig. 3
Fig. 1
Fig. 2
7
Disassembly 8. See Fig. 4. Remove (2) rear shell mounting
bolts. Save hardware. 9. Carefully pull straight up on rear shell to re-
move from motorcycle. 10. Remove antenna boot from seat shell. 11. See Fig. 5. Remove key latch assembly. Dis-
connect cable and save latch. 12. See Fig. 6. Remove LH/RH release assem-
blies. Save all hardware. 13. See Fig. 6 Remove antenna mounting and lay
antenna out of the way. Save hardware. 14. See Fig. 6 Remove module box and temporar-
ily move out of the way. Save hardware.
PREPARING THE MOTORCYCLE
Fig. 6
Fig. 4
Fig. 5
Antenna
Module box
Release assemblies
8
Saddlebag Disassembly 1. See Fig. 1. Remove LH and RH side covers.
Remove and save short screws from exten-sions. Side cover extensions will not be reused.
2. See Fig. 2. Remove and save side cover grom-mets from front of saddlebags.
3. See Fig. 2 Remove upper front saddlebag mounting bolts. Save washers only.
4. Disconnect battery by removing negative cable first.
5. Disconnect saddle bag latch cables 6. Raise trike on lift. 7. See Fig. 3. Remove rear fender cover.
PREPARING THE MOTORCYCLE
Fig. 3
Fig. 1
Fig. 2
Save washers
Save grommets
9
Disassembly 8. See Fig. 4. Remove upper saddlebag support
bar. Save hardware. 9. Remove saddlebags from motorcycle. 10. See Fig. 5. Remove and save the following
from the LH saddlebag only. • Latch assembly and mounting screws • Door strikers and mounting screws • Latch cable • LH saddlebag harness w/USB connector
and cap. 11. See Fig. 6. Remove and save (4) amplifier
box mounting bolts. Remove amplifier from rear fender.
NOTE: Long bolts (upper) will be reused for brake line clamp installation and side stand switch disabling. Short bolts (lower) will be used for amplifier installation on trike.
PREPARING THE MOTORCYCLE
Fig. 5
Fig. 4
LH hardware shown
Fig. 6
10
Disassembly 12. Remove and save LH/RH passenger foot
boards and mounting hardware. 13. See Fig. 7. Remove and save rear frame
covers. Save front mounting bolts (2) only. 14. See Fig. 7. Remove and save swingarm pin
covers and hardware. 15. Remove and discard rear crash guards and
hardware. 16. See Fig 8. Loosen muffler clamps. Remove
and save muffler mounting bolts and remove mufflers. Remove and save rubber inserts from heat shields.
17. See Fig. 8. Remove and save metal inserts and rubber bushings from saddlebag sup-ports.
18. Remove and save (4) nuts from heat shield on RH muffler. Discard heat shield.
PREPARING THE MOTORCYCLE Fig. 7
Discard rear bolt Pin cover
Frame cover
Fig. 8
Save mounting hardware
Save rubber inserts
11
Disassembly 19. See Fig. 10. Remove and save rear inner plas-
tic fender mounting bolts. 20. Remove rear wheel with 19mm socket. Dis-
card wheel nuts. 21. See Fig. 10. Remove side stand switch as-
sembly. Disconnect sensor from side stand while stand is in the “up” position.
22. See Fig. 11. Secure sensor from turning using the following hardware. • (1) Original Upper Amp Mounting Bolt • (1) Original Upper Saddlebag Washer • (1) M6 Flange Lock Nut- CN1902
PREPARING THE MOTORCYCLE
Fig. 11
Fig. 9
Fig. 10
Remove side stand
Secure sensor
12
Tour Box Frame Modification 1. See Fig 1. Mark and cut tour box frame as
shown with reciprocating saw or equivalent. 2. Remove tour box frame from motorcycle frame.
And discard mounting hardware. Use touchup paint on bottom of tour box frame where cuts were made.
PREPARING THE MOTORCYCLE Fig. 1
13
Fender Modification TRIMMING FENDER CAUTION: Do not cut electrical components. 1. See Fig. 3. Mark and Cut amplifier box 1” in
front of rubber cover. 2. See Fig. 4. Mark and cut front half of fender
5 1/2” from rear.
PREPARING THE MOTORCYCLE Fig. 1
Fig. 2
Mark and trim 1” from rubber cover
5-1/2”
Trim here
14
Driveline and Suspension Disassembly NOTE: Temporarily leave brake lines attached to caliper. 1. See Fig. 1. Remove rear caliper mounting
bolts with 14mm socket. Free brake lines from final drive assembly clips.
2. See Fig. 2. Remove front and rear brackets holding brake lines to swingarm. Save front mounting bracket.
3. See Fig. 3. Remove final drive assembly from swingarm using 17mm wrench.
4. Remove driveshaft from swingarm tunnel.
PREPARING THE MOTORCYCLE
Fig. 3
Fig. 1
Fig. 2
Caliper mounting
Remove from clips
Save front bracket
Rear bracket
Final drive Swingarm
15
Driveline and Suspension Disassembly 5. See Fig. 4. Remove shock adjuster assembly
from bracket. 6. See Fig. 5. Remove upper shock nut through
RH side of frame using a 17mm socket and 6” extension. Hold bolt head through LH side of frame with 8mm Allen socket and 6” extension.
7. See Fig. 6. Remove rear linkage bolt with 17mm and 19mm sockets. Remove front link-age bolt from motorcycle frame using 19mm socket and 10mm Allen socket.
8. See Fig. 6. Remove lower shock bolt with 14mm and 17mm sockets.
9. See Fig 6. Raise swingarm and remove swin-garm linkage bolt with 19mm socket and 10mm Allen socket.
10. Remove and save LH swingarm pin lock nut. Remove LH and RH swingarm pins with 19mm Allen socket.
11. Remove OEM swingarm. Feed shock through top of swingarm during removal.
12. Remove rubber boot from transmission and discard.
13. Remove shock assembly from motorcycle. 14. Reinstall battery box and battery. Leave nega-
tive cable disconnected.
PREPARING THE MOTORCYCLE
Fig. 6
Fig. 4
Fig. 5
RH side shown
Access to upper shock nut
Remove all shock linkage and hardware
16
Brake System Modification OEM brake system and trike modifications The original Honda motorcycle brake system utilizes both front and rear brakes when the foot brake is applied. During the trike conversion the brake system will be modified. Once modification is complete, the rear brake pedal will maintain front and rear linked braking. The front brake lever will operate the front brakes only. The anti-dive valve feature is maintained on both front and rear braking. The diagrams below outline the difference between the original Honda GL1800 brake system and the modified Trikes brake system.
PREPARING THE MOTORCYCLE
Fig. 1 Fig. 2
Original system Modified system
17
Brake System Modification- Rear 1. See Fig. 1. Disconnect inner rear brake line
(upper line on caliper). 2. Disconnect upper line at caliper and discard
brake line. NOTE: Allow brake line to drain before blocking off. 3. Block off inner brake line using the following
hardware. • (1) M10 Banjo Bolt– CB6001
• (2) Copper Banjo Washers– GC6002
• (1) 1/2” Spacer– S001067 4. See Fig 2. Using cable ties, secure discon-
nected brake line to top of crossbar on frame. 5. Disconnect lower brake line from caliper. 6. See Fig. 3. Route brake line above plastic
panel on RH side where shock compressor was originally located.
7. Drill 1/4” hole in plastic and mount brake line using the following hardware that was saved from disassembly. • (1) Original Front Brake Line Clamp • (1) Original Upper Amplifier Mounting Bolt • (1) Original Saddlebag Washer • (1) M6 Lock Nut– CN1902
PREPARING THE MOTORCYCLE Fig. 1
Fig. 2
Disconnect inner brake line at fitting
Fig. 3
Secure line above crossbar
Mount to plastic with original clamp
Block off line
18
Brake System Modification- Front 1. Remove front fenders and wheel covers. 2. See Fig’s. 1 & 2. Remove OEM line from anti-
dive valve and front master cylinder. Line con-tinues to junction block located on steering head. Disconnect lower hard line from block. Remove block from frame and remove entire line from motorcycle.
3. See Fig. 3. Install new brake line between anti-dive valve and master cylinder using OEM banjo bolts and the following hardware. Torque banjo bolts to 18 ft-lbs. • (1) Front brake line- S002066
• (4) Copper Banjo Washers– GC6002
PREPARING THE MOTORCYCLE Fig. 1
Fig. 2
Fig. 3
Anti-dive valve
Master cylinder
New line installed
Remove lower line from block
Disconnect block
19
Swingarm Installation NOTE: The OEM transmission rubber boot is not reused. 1. Place a small amount of anti-size to threads on
swingarm pins. Start swingarm pins into mo-torcycle frame.
2. See Fig. 1. Place trike swingarm into motorcy-cle frame. Start pins into swingarm.
3. See Fig. 2. Tighten RH swingarm pin with 19mm Allen socket. Torque RH pin to 80 ft-lbs.
CAUTION: Do not over tighten LH swingarm pin. Tighten just enough to seat pin into swin-garm. 4. See Fig. 3. Tighten LH swingarm pin with
19mm socket. Torque LH pin to 25 ft-lbs. 5. Move swingarm up and down to ensure bear-
ings are properly seated. Re-torque LH swin-garm pin to 25 ft-lbs.
6. Install LH OEM lock nut using Loctite 242. Torque lock nut to 80 ft-lbs. using Honda lock-nut wrench 07MA-MCA100.
7. Reinstall swingarm pin covers with original hardware.
INSTALLATION
Fig. 3
Fig. 1
Fig. 2
20
Differential/Suspension Installation
1. See Fig. 1. Loosen top and middle brackets where they attach to main differential assembly. WARNING: Differential assembly is extremely
heavy. Verify assembly is properly supported and secure while installing to motorcycle. Additional help may be required during installation. 2. See Fig. 2. Attach differential assembly (bottom
brackets) to swingarm using the following hardware.
• (2) 1/2” x 2-1/2” Socket Bolts- CB1999 (upper)
• (2) 1/2” x 3” Hex Bolts- CB1998 (lower)
• (2) Serrated Lock Washers- CW2179
• (6) 1/2” Flat Washers- CW2178
• (4) 1/2” Lock Nuts- CN3060 3. See Fig 3. Attach the middle bracket to the Honda
frame using the following hardware.
• (4) M8 x 30 Hex Bolt- CB1620 (#1)
• (2) M8 x 50 Hex Bolt- CB2005 (#2)
• (6) M8 Lock Washer- CW2168 (Use on bolt head)
• (6) M8 Flat Washer- CW2167 (Use on bolt head)
• (4) 5/16 Flat Washer– CW2183 (#3)
• (1) Spacer– S002069 (#4)
INSTALLATION
Fig. 2
Fig. 1
Fig. 3
Middle bracket
Bottom bracket
Top bracket
Socket head bolt with serrated washer in upper hole
1
2
1
3
4
21
Differential/Suspension Installation 4. See Fig. 4 & 5. Temporarily install and tighten
tour box frame using the following hardware. • (2) M8 x 60 Hex Bolts-CB2007 (Upper holes)
• (2) M8 X 50 Hex Bolts-CB2005 (Lower holes)
• (2) M8 Lock Nuts- CN1908 (Upper bolts)
• (2) M8 Lock Washers-CW2168 (Lower bolts)
• (6) M8 Flat Washers- CW2167 5. See Fig. 5. Measure distance between tour box
frame and body frame as shown. Adjust tour box frame as needed to achieve 18” between frames.
6. See Fig. 5. Torque middle bracket mounting bolts to 15 ft-lbs.
7. See Fig. 6. Torque bottom bracket mounting bolts to 50 ft-lbs.
INSTALLATION
Fig. 5
Fig. 4
Fig. 6
Middle Bracket
Top Bracket
Bottom Bracket
18”
22
Differential/Suspension Installation 8. See Fig. 7. Torque top bracket hardware to 35
ft-lbs. 9. See Fig. 7. Torque LH & RH top bracket to dif-
ferential housing hardware to 50 ft-lbs. NOTE: Leave tourbox frame installed on F6B models. 10. See Fig. 8. Modify OEM frame covers as needed
to fit over trike frame. Reinstall with original front mounting hardware. Secure to frame with cable ties on rear.
NOTE: See Fig. 9. Rear shocks are preset on the fourth setting (4 complete revolutions on lower collar) from the factory. Shocks have a total of 7 settings. Adjust shocks as needed.
INSTALLATION
Fig. 8
Fig. 7
Top bracket to differential hardware 50 ft-lbs.
Top bracket hardware 35 ft-lbs.
Trim rear of frame cover
Fig. 9
Soft Firm
23
Driveshaft Installation 1. Shift transmission into NEUTRAL. 2. See Fig. 1. Install U-joint to driveshaft yoke.
Grease fitting should face yoke. • (1) Driveshaft Yoke– LY1002
• (1) U-Joint– S002086 3. See Fig. 2. Apply Loctite retaining compound
(Green) to yoke splines and Install the stub shaft into yoke. End of shaft should be flush with yoke surface. Install set screw and torque to 19 ft-lbs. • (1) Stub Shaft– LS6305
• (1) Set Screw– CS3978 4. See Fig. 3. Install collar and spring to OEM
driveshaft as shown. • (1) Driveshaft Collar– S002091
• (1) Driveshaft Spring– S002201
INSTALLATION Fig. 1
Fig. 2
Shaft flush with yoke
Secure with set screw
24
Driveshaft Installation 5. Grease all internal splines on Honda motorcy-
cle yoke. NOTE: Ensure that centers of universal joints are aligned in phase as closely as possible (centers may not line up exactly). 6. See Fig. 4. Assemble drive shaft as shown. 7. Install drive shaft through swingarm tunnel and
onto output shaft of transmission. Ensure drive-shaft is fully engaged on transmission output shaft.
NOTE: Remove (2) outer caps from u-joint during installation. 8. Compress spring forward and rotate driveshaft
while working u-joint in place on rear yoke. Rein-stall caps and locate u-joint into yoke.
9. See Fig. 5. Attach driveshaft to differential yoke using the following hardware. Use Blue Loctite and Torque nuts to 18ft-lbs. • (1) U-Bolt kit– S002202
INSTALLATION Fig. 4
Fig. 5
Align U-joints
25
Brake System 1. Route brake line to residual valve on top of dif-
ferential. Verify torque on valve– 11 ft-lbs.(1) Residual Valve– S002037
2. See Fig. 2. Install brake line to residual valve using the following hardware. Torque banjo bolt to 16 ft-lbs. • (1) M10 Banjo Bolt– CB6001
• (2) Copper Banjo Washers– GC6002 3. Remove reservoir caps. 4. Bleed rear brake system at rear calipers with
brake bleeder or hand operated vacuum pump. 5. Bleed front brake system with rear pedal in the
following order. Refer to Honda service manual for further information. • Fig. 2. LH front, upper bleeder
• Fig. 3. RH front, lower bleeder
• Fig. 4. LH front, anti-dive valve 6. Repeat bleeding on front and rear until all air is
eliminated from brake system. Verify rear brake pedal and front brake lever are firm and do not bottom out.
7. Fill fluid reservoirs and install caps. NOTE: New brake pads and rotors will have a break-in period before optimum brake operation is achieved.
INSTALLATION Fig. 1
Install line to valve
Valve
Front LH upper bleeder
LH Anti-dive bleeder
Fig. 2
Fig. 3
Fig. 4
Front RH lower bleeder
26
Amplifier Installation 1. Remove metal inserts from amplifier mounting
holes. 2. See Fig. 1. Install amplifier mounting brackets to
motorcycle frame using the following hardware. • (2) Amplifier Mounting Brackets– LB6325
• (2) Bolts From OEM Inner Fender
• (2) Nuts From OEM License Plate Bracket NOTE: LH bracket is mounted on inside of frame tab. RH bracket is mounted on outside of frame tab. 3. See Fig. 1. Mount amplifier box using the follow-
ing hardware. • (2) Bolts From OEM Rear Fender Cover
• (2) 5/16” Flat Washers– CW2010
• (2) Nuts From OEM Heat Shield 4. See Fig. 2. Drill 1/4” holes where plastic fender
and amplifier box overlap. Install with the follow-ing hardware. • (2) Bolts From OEM Amplifier Box Mounting
• (2) Nuts From OEM Heat Shield 5. See Fig. 3. Amplifier box should look as shown
when complete.
INSTALLATION Fig. 1
LH bracket shown
Fig. 2
Fig. 3
RH attachment
27
Sway Bar Installation NOTE: Exhaust extensions must be installed before sway bar installation. 1. See Fig. 1. Install exhaust extensions to motor-
cycle pipes as shown. Leave hardware loose until mufflers are installed.
2. See Fig’s 2 & 3. Install sway bar to swingarm using the following hardware. Torque to 30ft-lbs. • (4) 3/8” x 1” Hex Bolts- CB2000
• (8) 3/8” Flat Washers- CW2180
• (4) 3/8” Lock Nuts- CN3051 2. See Fig. 4. Install sway bar rod ends to LH and
RH control arms using the following hardware. Install one washer to each side of rod end. • (2) 3/8” x 2-1/4” Hex Bolt- CB2001
• (6) 25/64” Stainless Flat Washers-CW2182
• (2) 3/8” Lock Nut- CN3051 3. Adjust rod end on LH side in or out until bolt
moves freely. 4. Tighten jam nuts on rod ends. 5. Tighten rod end hardware. Torque to 30ft-lbs.
INSTALLATION
Fig. 2
Fig. 3
Fig. 4
Attach to Swingarm
Install washers
Fig. 1
S002067
28
Park Brake Installation 1. See Fig. 1. Attach park brake lever to bracket as
shown. 2. See Fig. 2. Install park brake bracket to sway
bar on LH side. Bracket should be 4” from out-side of sway bar. Install using the following hard-ware. • (1) U-Bolt- S002047
• (2) 3/8” Thin Lock Nut- CN3055
• (2) 3/8” Flat Washer– CW2180 3. See Fig. 3. Verify park brake cables are se-
cured to differential housing with clamps and cable ties as shown.
4. See Fig. 4. Attach park brake cables to bracket using nuts and washers provided on the cables.
5. See Fig. 4. Attach cables to pulling bracket us-ing 5/16” nut on each side. • (2) 5/16” Nut- CN3009
6. Adjust cables until brake system holds at 3-4 clicks on lever. Tighten 5/16” nuts against bracket.
7. Install park brake boot over lever. Secure with cable tie.
CAUTION: Ensure boot is not interfering with LH muffler. Damage to boot may occur.
INSTALLATION Fig. 1
Fig. 2
Fig. 3
Item# Part# Description 1 GB1099M Park Brake Lever 2 LB1294 Cable Pulling Bracket 3 CC3106 Clevis Pin 4 CC4017 Cotter Pin 5 S002048 Park Brake Bracket
1
3,4
2
5
Attach cables to brackets
Nuts on each side
4”
Fig. 3
Clamps
29
Latch Modification 1. See Fig. 1. Remove release cable and plastic
clip from LH latch assembly. 2. See Fig. 1. Bend cable tab straight. 3. See Fig. 1. Remove original release lever. 4. See Fig. 1. Replace original latch rod.
• (1) Latch Rod- S001783 5. See Fig. 2. Install cable extension using the
following hardware. NOTE: Tighten screw just enough to engage lock nut. Over tightening will cause extension bracket to bind up.
• (1) Cable Extension– LB6319
• (1) 10/32” x 1/2” Machine Screw– CS4066
• (1) 10/32” Lock Nut– CN3068 6. See Fig. 2. Install latch assembly and cable
bracket to latch bracket using the following hard-ware.
• (1) Latch Mount Bracket– LB6302
• (1) Cable Bracket– LB6320
• (4) OEM Phillips Screws (From Saddlebag) 7. See Fig. 2. Install cable clip and cable to new
extension. 8. Test latches to verify they release at the
same time. Adjust rod length as needed. Door may not release properly if latches do not release together.
9. See Fig. 2. Install cable clamp to safety re-lease cable. Loop cable through small hole in cable extension bracket and crimp cable clamp. • (1) Cable Clamp- CC1900
• (56”) Safety Cable 10. See Fig. 3. Complete latch assembly should
look as shown.
LATCH MODIFICATION Fig. 1
Fig. 2
Fig. 3
Bend cable tab straight
Remove clip and cable Remove release lever
Latch bracket
Cable bracket
Extension
Safety cable
Replace original latch rod
30
Latch Installation 1. See Fig. 1. Install latch assembly into trunk us-
ing the following hardware. Leave latch loose to move in slots. • (4) M6 x 16 Button Head Bolts- CB1904
• (4) M6 Fender Washers- CW2107 2. See Fig. 2. Route latch cable through large hole
in front trunk wall. Secure grommet in hole. 3. See Fig. 2. Route safety release cable through
small hole in front trunk wall. 4. Apply silicone around safety release cable from
inside trunk.
LATCH INSTALLATION Fig. 1
Fig. 2
Safety cable
Latch cable
31
Body Preparation 1. See Fig. 1. Install side cover brackets to body
using the following hardware. • (1) LH Side Cover Bracket- LF6305-BL • (1) RH Side Cover Bracket- LF6305-BR • (4) M6 x 25 Button Head Bolts– CB1911 • (4) M6 Fender Washers– CW2107 • (4) M6 Lock Nuts– CN1902
2. See Fig. 1. Install grommets (from OEM saddle-bags) into side cover brackets.
3. Install trike wiring harness to plastic clips on body.
4. See Fig’s. 2 & 3. Original side covers must be modified before installing extensions. Modify side covers as shown. Additional trim may be neces-sary.
NOTE: Remove original mounting peg from back-side of upper LH rear side cover 5. Install side cover extensions to OEM side covers
using original hardware. Install trim seal along back edge of extension. • (2’) Trim Seal- CW2505
BODY PREPARATION Fig. 1
Fig. 2
Fig. 3
LH side cover
Remove rear section
RH side cover
Remove peg from backside
32
Body Preparation NOTE: Orange wire on turn signal connector will route to LH side. Blue wire on turn signal con-nector will route to RH side. Route trailer harness wiring down LH side with LH taillight wiring. 6. Install wiring harness to body
• (1) F6B Body Harness- S002132 7. See Fig. 4. Install harness grommets through
taillight pockets on each side. Install large grom-met before installing lights.
8. See Fig. 5. Connect taillights to harness and carefully install into body using the following hardware. • (6) 1/4” Stainless Flat Washers- CW2008 • (6) M5 Taillight Mounting Nuts- CN1711
9. See Fig. 5. Plug extra taillight mounting holes (locations vary by model year) with silicone.
10. See Fig. 6. Install original LH saddlebag harness with USB plug through center hole in trunk. Split original saddlebag grommet and route license plate wiring in grommet.
11. Install grommet in body. Apply silicone around harness and grommet from inside trunk
BODY PREPARATION Fig. 4
Fig. 5
Large Grommet
Silicone extra holes
Grommet
Fig. 6
Original saddlebag grommet LH saddlebag
wiring with license plate wiring
33
Body Preparation 12. Install plastic connectors onto license plate and
accessory terminals inside trunk. Install black female connector for accessory wires to brown (+) and green (-) wires on harness and secure to wire clips. This is an additional 12 volt power source for any powered accessories that may be added later.
13. Plug original saddlebag harness into latch as-sembly.
14. Apply silicone around harness and grommet from inside trunk.
15. Route license plate wiring inside trunk along roof and LH trunk wall. License plate wiring will be completed once door is installed.
16. See Fig. 5. Drill a small hole in latch cover to accommodate cap for USB plug.
17. Remove 6 position connector from host motorcy-cle harness.
18. Install male terminals and female connector to host motorcycle harness. Match wiring on trike harness to wiring on OEM harness. NOTE: Green wires with Red tracers will go to solid red wire on trike harness.
19. Use appropriate tool for crimping terminals to wires. (Mac Tools– TCT1028, Blue Point– PWC47 or H-D 41609).
20. See Fig. 7. Inspect crimps before installing into connector. Distortion should be minimal.
BODY PREPARATION Fig. 5
Fig. 6
Trike harness
Install terminals and connector to OEM harness
Fig. 7
Wire core crimp
Insulation crimp
34
Door Installation NOTE: Remove any residue from seal mounting surface on door before installing seal. 1. See Fig. 1. Install trunk door seal starting at the
bottom center of trunk opening. Solid lip on seal will face trunk edge.
2. See Fig. 2. Install original strikers and hardware from LH saddlebag to top of trunk door.
3. Verify hinges are in the middle of adjustment slots in trunk.
4. See Fig. 3. Before installing door, check spacing of door hinges for consistency from side to side. If hinges are not equal, loosen hardware on crossbar between hinges. Twist bar until hinges are equal and tighten hardware.
DOOR INSTALLATION Fig. 1
Fig. 2
Fig. 3
Consistent spacing
Crossbar
RH striker shown
Start seal here
35
Door Installation 5. See Fig. 4. Install trunk door to body using the
following hardware. Leave hardware loose. • (6) M6 x 16 Button Head Bolts- CB1904 • (6) M6 Fender Washers- CW2107
CAUTION: Slowly close door and ensure strikers clear top of trunk opening. Bend strikers down if necessary. Strikers should just clear opening. 6. Slowly close door (do not try to latch door at
this time). Adjust door from side to side and up and down to match body. Once door is in place, slowly open and tighten mounting hardware.
7. See Fig. 5. Lower door and check for consistent spacing between door and body.
8. Pull latch assembly towards rear of body and tighten hardware. Align strikers from side to side to match opening on each latch.
9. Latch door. Verify that both side latch when closed. Adjust latch assembly in or out as needed.
10. See Fig. 6. Door adjustment is made using the following: • Moving hinges upward in trunk results in the
top of door tilting outward and away from body.
• Moving hinges downward will bring door closer to body.
• Latch can be slide in or out to adjust gap on top and take out any excessive play in door.
11. Once all door adjustments are made and hard-ware is secure, install plastic latch cover using original Phillips head screws from LH saddlebag. • (1) Latch Cover– LC6300
12. See Fig. 7. Drill a small hole in latch cover to accommodate cap for USB plug.
DOOR INSTALLATION
Fig. 4
Fig. 5
Fig. 6
Consistent spacing
Loosen bolt and adjust as needed
Door mounting
Fig. 7
36
License Plate Light Installation 1. See Fig. 1. Install rubber inserts in to trunk door.
• (2) 10-32” Rubber Insert- CN2103 2. See Fig 1. Drill 5/32” hole next to LH insert. 3. Insert license plate light wire through drilled hole. 4. See Fig. 2. Install light assembly to door using
the following hardware. Install spacers between light and rubber inserts • (2) 1/4” Spacer- S001369 • (2) 10-32” x 1” Button Head Bolt- CB2016 • (2) #10 Flat Washer- CW2002
5. Once light is installed, seal wire with silicone on inside of trunk door.
6. Match license plate wiring to trike body harness as shown. Green wire on harness is negative (-). • Black (-) wire on light to Green/Yellow (-)
wire on harness • Red (+) wire on light to Brown (+) wire on har-
ness 7. Install female terminals and male connector to
license plate light wiring. 8. See Fig. 3. Route wiring along top of trunk roof
and hinge assembly and connect to license plate harness. Use cable ties to secure wiring as needed. • (7) 6” Cable Tie– CT1014
DOOR INSTALLATION Fig. 1
Fig. 2
Drill hole
Fig. 3
Route wiring along hinge assembly
37
Body Installation Note: The installation/alignment of the body is an important process to find the correct position of the body in relation to the wheels. The pre-drilled holes in the body are for shipping purposes. Re-drill the holes if necessary once body is properly aligned. 1. Carefully lower body into position on trike frame. 2. Install side covers. Pull body forward as needed
to align all side cover grommets. 3. Install body spacers between frame and body.
Place 1/4” rubber spacers on front mounting tabs. Place 7/8” solid spacers on rear mounting tabs. • (2) 1/4” Rubber Spacers- CW2098 • (3) 7/8” Solid Spacers- S002124
4. See Fig’s 1 & 2. Align body to trike. Center body by checking side to side (wheel opening) and front to back (front of fender) measurements.
5. Ensure gaps at side covers are tight and equal on both sides.
6. See Fig. 3. With the body in the proper location, drill a 3/8” hole through the 5 holes located on the frame.
7. Attach body to frame using the following hard-ware. Use fender washers against bolt heads. 2” bolts are used in the front mounting holes. • (2) 3/8” x 2” Button Head Bolts- CB2014 • (3) 3/8” x 2-1/4” Button Head Bolts- CB2015 • (5) 3/8” Fender Washers- CW2181 • (5) 3/8” Flat Washers- CW2180 • (5) 3/8” Lock Nuts- CN3050
8. Tighten all body mounting bolts.
BODY INSTALLATION Fig. 1
Fig. 2
Fig. 3
38
Body Installation 9. See Fig. 4. Attach LH park brake cable
bracket and clamp to front body mount bolts using the following hardware. • (1) Bracket- S002143 • (1) Clamp- S001654 (5/16” bolt hole) • (1) M8 x 20 Flange Bolts- CB1919
• (1) M8 Flat Washers- CW2167
• (1) M8 Lock Nut- CN1908 NOTE: Verify that LH cable is secured to upper A-arm with cable ties. LH cable should be se-cured towards inside of trike to prevent inter-ference with wheel and tire. 10. See Fig. 5. Attach RH park brake cable to front
body mount bolts using the following hard-ware. • (1) Clamp- GC0108 (3/8” bolt hole) • (1) 3/8” Lock Nut- CN3050
BODY INSTALLATION Fig. 4
Fig. 5
RH Cable
Front of trike
LH Cable
Front of trike
Bracket
Clamp
39
Muffler Installation 1. Install original exhaust gasket (replace if worn or
damaged) to exhaust extension. Slide muffler onto extension pipe.
2. See Fig. 2. Install muffler brackets to frame us-ing the following hardware. • (2) F6B Muffler Brackets- S002133
• (4) M8 x 20 Flange Bolts- CB1919
• (4) M8 Flat Washers- CW2167
• (4) M8 Lock Nuts- CN1908 3. Install muffler to bracket using the original muf-
fler mounting hardware (Bolts, rubber bushings and sleeves).
4. Adjust mufflers in rear body cutouts. Make sure mufflers match from side to side.
5. Tighten all mounting hardware and clamps for extension pipes and mufflers.
MUFFLER INSTALLATION Fig. 1
40
Trunk Lock Relocation 1. See Fig. 1. Bend original mounting tab flat on
trunk lock assembly. 2. See Fig. 2. Set bracket in place on lock and
mark hole. Drill hole to 1/4”. • (1) Trunk Lock Bracket– S002100
3. See Fig. 3. Attach lock to bracket using the fol-lowing hardware. • (2) 10/32” Pan Head Screw- CS4066 • (2) 10/32” Lock Nut– CN3068
TRUNK LOCK ASSEMBLY Fig. 1
Fig. 2
Mark and drill hole
Fig. 3
41
4. See Fig. 4. Re-attach original release cable to
trunk lock. Route cable on outside of Honda frame on RH side.
5. See Fig. 5. Attach trunk lock assembly to fuel tank bracket on RH side. Leave hardware loose. • (2) M6 x 16 Flange Bolt- CB1904
6. Install grommet into RH side cover. • (1) Side Cover Grommet– S002110
7. Install RH side cover and check alignment with trunk lock. Adjust lock as needed and tighten hardware.
8. See Fig. 6. Mount release assemblies in original locations on OEM frame using the original mounting hardware.
TRUNK LOCK ASSEMBLY Fig. 4
Fig. 5
Route and re-attach cable
Fig. 6
42
9. See Fig. 7. LH release assembly is only used for
grab handle alignment. Lock assembly in place as shown with take off hardware.
10. See Fig. 8. Route emergency release cable be-hind RH side cover and secure to frame rail with cable tie. Install cable clamp and make small loop. Crimp cable clamp and secure to front of tour box • (1) Cable Clamp- CC1900
TRUNK LOCK ASSEMBLY Fig. 7
Lock in place
Fig. 8
LH assembly
Emergency release cable
43
NOTE: Verify all OEM components are proper location before installing seat shell. (Wiring, An-tenna, Module box) 1. Install trim around rear seat shell.
• (6’) Trim– GT1800 2. Install OEM grommets to shell for grab handles. 3. Install OEM antenna boot to shell. 4. Apply tape to top of body where seat shell will
sit. 5. Set shell in place on body. Align front of shell to
latch assemblies and seat mounting holes. 6. See Fig. 1. Once shell is properly aligned to
body, mark stud location on top of body and re-move shell.
7. Drill holes using 1/4” drill bit. 8. See Fig. 2. Install hardware to studs on seat
shell. • (2) M6 Lock Nut- CN1903 • (2) M6 Fender Washer- CW2107 • (2) Rubber Washer– CW2094
8. Reinstall seat shell and verify fitment. Trim holes as needed to achieve proper alignment.
9. Attach shell to body from inside trunk using the following hardware. Use silicone around studs to ensure proper seal with body. Tighten down hardware evenly. • (2) M6 Fender Washer- CW2107 • (2) M6 Lock Nut- CN1903 • (2) M6 Acorn Nut– CN1918
10. See Fig. 3. Install seat and grab handles using original hardware. Very that RH trunk release lever functions proper when activated. Trim seat shell if necessary.
REAR SEAT SHELL Fig. 1
Fig. 2
Fig. 3
44
Final Assembly 1. Plug in all electrical connectors from trike har-
ness to motorcycle harness. 2. Connect battery and check lights for proper op-
eration. 3. Install passenger footboards using original hard-
ware. 4. Verify all side covers are reinstalled. 4. Install wheels and torque lug nuts to 85 ft-lbs.
Install center caps (if applicable). 5. See Fig. 1. Install badges on trunk door. Place
Lehman badge on LH side and Monarch II LLS badge on RH side.
6. Remove motorcycle center stand (if applicable). NOTE: RH center stand bolt has LH threads.
FINAL ASSEMBLY Fig. 1