Upload
hoangkhue
View
219
Download
0
Embed Size (px)
Citation preview
L e a d i n g t h e W a y i n T h i n M a s o n r y S u p p o r t T e c h n o l o g y
g l e n g e r y . c o m
FEATURES & BENEFITS
Patent pending support tie configuration placed on a 76 degree angle
• Allows the mortar to surround the support tie creating a positive masonry lock between the brick mortar and panel
G-90 galvanized and thermal set coating
• Provides barrier rust prevention
• Light color helps reflect and evenly distribute heat
Stucco embossed texture
• Provides a built-in weep system on both sides of panel formoisture control
• Creates greater surface area for maximum adhesion betweenveneer and panel
26-gauge architectural grade steel
• High fastener pull-through strength for panel support and integrity
• Harden steel sheets help brace wall, minimizing wall racking
• Allows fastening anywhere through the panel for even weight distribution or loading on the wall, using industry standard fasteners
Lightweight design
• Reduces footings and lintel requirements
• Cost-efficient wall design
• Reduced labor costs
GLEN-GERY THIN TECH®
CLASSIC SERIES
Your traditional choice with our patent pending locking support tie.
Glen-Gery Thin Tech® is a mechanical support
and spacing panel for thin masonry veneers. The
strongest, most durable thin veneer panel system
ever designed.
Each thin brick,
tile or stone is
supported by our
patent pending support ties that mechanically
interlock the masonry veneer to the panel.
WALL CONSTRUCTION
AIR & WATER BARRIER
ADHESIVE / MASTIC -APPLIED IN VERTICAL STRIPSOR DABS - DON’T APPLYHORIZONTALLY
MORTAR - GROUT
MASONRY VENEER
CLASSIC PANEL
SUPPORT TIE
SUBSTRATE
INSULATION - THICKNESSAS SPECIFIED BYARCHITECT
NON-CORROSIVE FASTENER8" VERTICALLY,16" HORIZONTALLY,OR 1 SCREW/SQ. FT.
1/4" MORTAIRVENT®
Wall Section – Classic (with insulation)
g l e n g e r y . c o m
4" M
IN. A
T GR
ADE
2-1/
2" M
AX.
AS R
EQUI
RED
BY C
ODE
MA
SO
NR
Y FO
UN
DAT
ION
STR
UC
TU
RE A
BO
VE F
OU
ND
ATIO
N
TOP OFFOUNDATION
AIR & WATER BARRIER
CLASSIC PANEL
WEEP HOLESRECOMMENDED
16" TO 24" ON CENTER
MORTAR - GROUT
MASONRY VENEER
SUPPORT TIE
NON-CORROSIVETYPE FASTENER
ADHESIVE / MASTIC –APPLIED IN VERTICAL STRIPS
OR DABS – DON’T APPLYHORIZONTALLY
CORROSION RESISTANTFLASHING FASTENED TO
STRUCTURE ABOVE &ADHERED TO FOUNDATION
3"
MASONRY FOUNDATION
FINISH GRADE
"X" TO BE DETERMINEDBY STEM THICKNESS
2" M
IN.
AT P
AVIN
G
"X"
1/4" MORTAIRVENT®
OPTIONAL REMOVE3/8" LIP AT BOTTOM
OF PANEL ATSTARTER COURSE
3/8"
Base Detail – Classic
G l e n - G e r y T h i n Te c h ® i s a v a i l a b l e i n C l a s s i c a n d E l i t e s e
GLEN-GERY THIN TECH®
ELITE SERIES – the most advanced masonry support system ever designed
Your choice for superior performance while maintaining all the features and benefits of the Classic Series.
L e a d i n g t h e W a y i n T h i n M a s o n r y S u p p o r t T e c h n o l o g y
NON-CORROSIVE FASTENER8" VERTICALLY,16" HORIZONTALLY,OR 1 SCREW/SQ. FT.
SUPPORT TIE
SUBSTRATE
AIR & WATER BARRIER
MASONRY VENEER
MORTAR - GROUT
FLASHING
AIRFL
OW-D
RAINAG
E
AIR
FLO
W
AIR
FLO
W
AIR
FLO
W
AIR
FLO
W
AIR
FLO
W
AIR
FLO
W
CHAMBER
ELITE PANEL
THIN TECH AIR VENT 3/8" x 1/2"
AIR
FLO
W
AIR FLOW THROUGHOPENING IN
THIN TECH AIR VENT
SUPPORT TIE
ELITE PANEL
MASONRY VENEER
AIR & WATER BARRIER
FLASHING
GRADE
3/8" x 1/2"
WALL CONSTRUCTION
AIR & WATER BARRIER
ADHESIVE / MASTIC - APPLIEDIN VERTICAL STRIPS OR DABS -DON'T APPLY HORIZONTALLY
MORTAR - GROUT
MASONRY VENEERELITE PANEL
SUPPORT TIE
AIR FLOW / DRAINAGE CHAMBER
INSULATION - THICKNESSAS SPECIFIED BYARCHITECT
SUBSTRATE
NON-CORROSIVE FASTENER8" VERTICALLY,16" HORIZONTALLY,OR 1 SCREW/SQ. FT.
Wind is one of the main contributing forcescausing rain penetration in a building. Whenwind blows on the face of a building, it forceswater through even the smallest opening. A wall utilizing rain screen technology isdesigned to counteract the pressure of thewind. When wind hits the Glen-Gery ThinTech® “Elite” wall it forces air into the airflowchambers, causing the chambers to reachthe same pressure as the wind; thus the netpressure difference across the cladding isnear zero. As a result, the wall pressure isequalized and the driving force for pressure-induced water penetration is eliminated.
Plan View – Elite (with insulation)
Axonometric Diagram
Air Flow & Ventilation DiagramGlen-Gery Thin Tech® Eliteprovides a true screen-drained wall system with:
Superior DrainageSuperior Bond StrengthSuperior Air Flow and VentilationSuperior Pressure EqualizationPlus Rain Screen Technology
Air Pressure Diagram
WIND PRESSURE HOUSE PRESSURE
AIR
FLOW
AIR
FLOW
HOUSE PRESSUREWIND PRESSURE
r i e s . E a c h s e r i e s o f f e r s m u l t i p l e f a c e h e i g h t s o f s u p p o r t t i e s a l l o w i n g f o r m a x i m um d e s i g n f l e x i b i l i t y .
© 2016 Glen-Gery Corporation 11/15/TSG/10M
Product Size Weight Packaging Coverage (Approximate)
Thin Tech Support Tie Ledge Panel* 48" x 48" 16 lbs. ea. As needed 16 sq. ft./panel(Classic or Elite) (nominal)
Thin Tech Pre-Bent Corner Panel* 48" x 16" x 32" 16 lbs. ea. As needed 16 sq. ft./panel(Classic or Elite) (48" nominal)
Thin Tech Shim 4' lengths .4 lbs. ea. As needed 4 linear ft./piece
Starter Angle 10' lengths 3.5 lbs. ea. As needed 10 linear ft./piece
Thin Tech Air Vent 4' lengths .75 lbs. ea. As needed 4 linear ft./piece
Adhesive 29 oz. tube 3 lbs. ea. 12 tubes/case 16 sq. ft./tube**
Mortairvent® (.25 in./6mm) 39" x 61.5' 14 lbs. As needed 200 sq. ft./roll
Glen-Gery Preblended Mortar 80 lb. bag 80 lbs. ea. As needed 80 sq. ft./bag***
1-1/2" Pan Head Square Drive Screw #10 x 1-1/2" 17 lbs. 1700/Box 1700 sq. ft./box for Steel
3-1/2" Pan Head Square Drive Screw #10 x 3-1/2" 17 lbs. 850/Box 850 sq. ft./box for Steel
1-1/2" Pan Head Square Drive Screw 3/16" x 1-1/2" 17 lbs. 1700/Box 1700 sq. ft./box for Wood and Concrete
3-1/2" Pan Head Square Drive Screw 3/16" x 3-1/2" 17 lbs. 850/Box 850 sq. ft./box for Wood and Concrete
GLEN-GERY THIN TECH® ACCESSORIES
Glen-Gery continues to lead the way in thin masonry support technology by stocking a full line of high-quality accessories. These accessories are recommended for the Elite and Classic Series panel systems and availablethrough our authorized Thin Tech® distribution network.
Thin Tech Support Tie Ledge Panel
Pre-punched panels are availablein Classic (shown above) and EliteSeries in multiple face heights ofsupport ties that correspond withspecific brick sizes allowing formaximum design flexibility.
Thin Tech Pre-Bent Corner Panel
Pre-punched and pre-bent cornerpanels available in Classic andElite (shown above) Series allowfor ease of installation at outsidecorners and continuous insulation.
Adhesive
HD construction adhesivedesigned for a wide range of construction applications and idealfor metal, brick, concrete andmost large panel type substrates.
Mortairvent®
Mortairvent®, a mortar deflection,drainage and ventilation systemspecifically designed for use withmasonry veneer applications.
Thin Tech Shim
Used with Elite panels to maintain a solid panel surfacewhen the installation requires the panel to be cut outsidethe vertical channels.
Starter Angle
Available in 24-guage stainless steel. Starter angles are tobe installed at base, floor lines, windows and doors.
Thin Tech Air Vent
Used with Elite panels at the starter angle or above windowand door openings improving aesthetics while maintainingproper water drainage and ventilation.
Glen-Gery Type N or Type SPreblended Mortar
Glen-Gery mortars are high- performance factory blends ofPortland cement, hydrated lime,and mason’s sand meeting ASTM C-144.
*Support tie spacing in following sizes: brick – 2-5/8", 3-1/8", 3-3/8",4"; stone – 8", 12", 16", 24". Available support tie sizes: 3/8" (standard), 5/8" and 7.5 mm**Corner brick will require 50% more adhesive • ***Coverage will vary depending on brick or stone
Fasteners
Pan head, square drive fasteners available in multiple sizes for steel, wood or concrete.
8 0 0 . 8 5 4 . 4 7 8 0g l e n g e r y. c o m