• Home

  • Documents

  • LAYOUT A3 P06623 MANUAL CENTRAL AGILITY · AGILITY CONTROL BOARD TECHNICAL MANUAL PXXXXX - Rev. 0...
MAIN FEATURES • Full Range AC Power Supply (90 – 240V); • Analog Limit Switch System; • RF receiver on-board; • EEProm Memory for storing both added remote controls and the control board setup; • Setup by pushbutton switches and eight levels by LEDs; • Up to 256 remote controls; • Electronic clutch (strength) adjustment; • Automatic acquiring (O/C path); • Input ports for photocell and pushbutton; • Output ports for receiver, electric lock and courtesy light modules; • Brake adjustment; • Independent adjustment of the travel stop ramp (opening and closing); • Preset opening delay when a traffic light is used; • Compatible with PROG. CHART: LED FUNCTIONS Guide for the functions of the indicator LEDs on the board, when it is not in programming mode, i.e., 'JPROG' jumper open. LED FUNCTION MEM (N1) • Lit: Empty memory, with no remote controls added. • Blinking: No memory or faulty memory. In this case, the control board enters the basic operation mode; it means that functions such as external PROG, the programming buttons and the remote controls get disabled.* FOT (N2) • Lit: Photocell triggered. CMD (N3) • Lit: External receiver or CMD button activated. BOT (N4) • Lit: External push button activated. TX (N5) • Lit: Added remote control detected. FCA (N6) • Lit: Open limit switch triggered. FCF (N7) • Lit: Closed limit switch triggered. SN (N8) • Blinks every two seconds: Normal operation. *BASIC OPERATION MODE Command only enabled by using an external pushbutton, 'CMD' button or external RF receiver; command during opening manouvre enabled, clutch on the maximum level; semi-automatic mode; ramps disabled; command for closing during the time pause; CLS and OLS (CLS = Closing Limit Switch / OLS = Opening Limit Switch) sensors Normally open and photocell normally open. CHART: SETTING CONFIGURATIONS Quick configuration guide. In order to enter programming mode, one must close the 'JPROG' jumper on the board. BUTTON FUNCTION TX Add or erase remote controls CMD Command when opening FORÇA Strength (Electronic clutch) PAUSA Automatic closing time RAMPAB ABRE Opening ramp RAMPFC FECHA Closing ramp RAMPTORQ TORQUE Ramp Torque (Strength) FREIO Brake LG GARAGEM Courtesy light time ERASING ALL REMOTE CONTROLS Erases and boots the memory in order to add new remote controls. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'TX' button on the control board (once); 4. N5 (TX) LED must remain lit; 5. Press the 'TX' button on the control board and keep it pressed for 10 seconds; 6. N8 LED must remain lit, indicating that all remote controls have been erased from the memory; 7. In order to finish, open JPROG jumper. ADDING REMOTE CONTROLS It adds new remote controls to the control board, so that they can trigger it. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'TX' button (once); 4. N5 (TX) LED must remain lit; 5. Press the button of the remote control one wants to add and keep it pressed; 6. N8 LED must remain blinking; 7. N8 LED blinks once (button already added), blinks twice (button already added and new synchronization for a Rolling Code Remote control) or three times (memory full); 8. Press and release the 'TX' button on the board to confirm the operation; 9. Release the button of the remote control; 10. Go back to step 3 to add a new button of the remote control; 11. In order to finish, open JPROG jumper. COMMAND DURING OPENING Permission for a command from either a push button or remote control to be accepted during the opening maneuver. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'CMD' button on the board (once); 4. Press and release the 'CMD' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Function enabled. • N2 lit = Function disabled. STRENGTH (ELECTRONIC CLUTCH) In order to assure the efficiency of this security sensor device, proceed as follows: - After properly installing the gate opener, adjust the electronic clutch so that the strength necessary to a complete gate maneuver is minimum when both opening and closing. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'FORÇA' button on the board (once); 4. Press and release the 'FORÇA' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Minimum. ... • N8 lit = Maximum. SEMI-AUTOMATIC / AUTOMATIC MODE (PAUSE TIME) It is the time adjustment for the automatic closing when the gate reaches the OLS limit switch sensor or the opening stop, indicating the limit of the opening maneuver. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'PAUSA' button on the board (once); 4. Press and release the 'PAUSA' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Semi-automatic. • N2 lit = 30 seconds. • N3 lit = 60 seconds. • N4 lit = 90 seconds. • N5 lit = 120 seconds. • N6 lit = 150 seconds. • N7 lit = 180 seconds. • N8 lit = 240 seconds. OPENING RAMP It is the distance between the opening mechanical stop and the point of the path where the electronic board enters torque control mode in order to decrease the speed of the gate and turn the opener off on the acquired path, i.e., the distance in which the opener starts decelerating when opening the gate. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'RAMPAB ABRE' button on the board (once); 4. Press and release the 'RAMPAB ABRE' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Function disabled. • N2 lit = 5% of the gate path. • N3 lit = 10% of the gate path. • N4 lit = 15% of the gate path. • N5 lit = 20% of the gate path. • N6 lit = 25% of the gate path. • N7 lit = 30% of the gate path. • N8 lit = 35% of the gate path. CLOSING RAMP It is the distance between the closing mechanical stop and the point of the path where the electronic board enters torque control mode in order to decrease the speed of the gate and turn the opener off on the acquired path, i.e., the distance in which the opener starts decelerating when closing the gate. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'RAMPAB FECHA' button on the board (once); 4. Press and release the 'RAMPAB FECHA' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. AGILITY CONTROL BOARD TECHNICAL MANUAL WARNING Do not use the equipment without referring to this manual first. LEDs sinalization: • N1 lit = Function disabled. • N2 lit = 5% of the gate path. • N3 lit = 10% of the gate path. • N4 lit = 15% of the gate path. • N5 lit = 20% of the gate path. • N6 lit = 25% of the gate path. • N7 lit = 30% of the gate path. • N8 lit = 35% of the gate path. TORQUE (STRENGTH) ON THE RAMP This adjustment decreases the gate speed when it is within the deceleration ramp area, i.e., the strength of the gate opener in the area of the limit switch ramp, close to the stops of the gate. In case it is disabled, the torque control on the ramp will be inoperative. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'RAMPTORQ TORQUE' button on the board (once); 4. Press and release the 'RAMPTORQ TORQUE' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Minimum. ... • N8 lit = Maximum. BRAKE It is activated when the motor is turned off by a command, or when the opener reaches the analog sensors (limit switches). Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'FREIO' button on the board (once); 4. Press and release the 'FREIO' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = Function disabled. • N2 lit = Minimum. ... • N8 lit = Maximum. COURTESY LIGHT TIME It selects the time in which the “LUZ” output will remain activated after the gate closes. During the opening or closing maneuver, or when the gate is still and open, the relay module will remain enabled. When the control board finishes the closing maneuver, the relay module will be disabled after the time set. Instructions: 1. The gate must be still; 2. Close JPROG jumper; 3. Press and release the 'LG GARAGEM' button on the board (once); 4. Press and release the 'LG GARAGEM' as many times as necessary until one reaches the desired adjustment; 5. In order to finish, open JPROG jumper. LEDs sinalization: • N1 lit = 10 seconds. • N2 lit = 30 seconds. • N3 lit = 60 seconds. • N4 lit = 90 seconds. • N5 lit = 120 seconds. • N6 lit = 150 seconds. • N7 lit = 180 seconds. • N8 lit = 240 seconds. ERASING THE ACQUIRED PATH It erases the path of the gate opener acquired by the control board. Instructions: 1. The gate must be still; 2. Keep JPROG jumper open; 3. Press the 'FREIO' button on the board and keep it pressed; 4. After 8 seconds, when all LEDs start blinking, release the 'FREIO' button. 5. Since the path is now erased, the control board will acquire a new path, and will finish this step after reaching the the opening and closing Reed-switches; NOTE: After 8 seconds, the LEDs will start blinking for a preset time interval and afterwards will be switched off. IMPORTANT In case the button is released while the LEDs are blinking, the board will run the chosen operation. However, if the button remains pressed while the LEDs are blinking, and is only released after they are switched off, the board will both cancel the operation and automatically exit the operation mode. DEFAULT FACTORY SETTINGS It restores the settings to their defeault parameters. Instructions: 1. The gate must be still; 2. Keep JPROG jumper open; 3. Press the 'RAMPTORQ TORQUE' button on the board and keep it pressed; 4. After 8 seconds, when all LEDs start blinking, release the 'RAMPTORQ TORQUE' button. 5. Now with the default factory settings restored to the board and with the path erased, the board will acquire a new path, and will finish this step after reaching the the opening and closing Reed-switches; NOTE: After 8 seconds, the LEDs will start blinking for a preset time interval and afterwards will be switched off. IMPORTANT In case the button is released while the LEDs are blinking, the board will run the chosen operation. However, if the button remains pressed while the LEDs are blinking, and is only released after they are switched off, the board will both cancel the operation and automatically exit the operation mode. 'F/R' JUMPER It reverses the direction of rotation of the motor, what is opening becomes closing and vice versa; it also reverses the logic of the limit switch sensors, OLS and CLS. CHART: SETTING THROUGH 'PROG' (PROGRAMMING TOOL) FUNCTION PARAMETERS HOME SCREEN Monitores the sensors and the peripherals of the board (OLS, CLS, pushbutton, photocell, remote control, Status of the board and timers (Courtesy light, Pause and Eletromagnectic lock)) ADDING REMOTE CONTROLS Add new remote controls to the board. PAUSE TIME • Semi-automatic • Time for automatic closing CLOSING RAMP 8 Levels OPENING RAMP 8 Levels STRENGTH (ELECTRONIC CLUTCH) 8 Levels COURTESY LIGHT TIME 8 Levels COMMAND WHEN OPENING • Enabled • Disabled ELECTRONIC BRAKE TIME 8 Levels ERASE REMOTE CONTROLS Erases all remote controls added to the board. TYPE OF REMOTE CONTROL • Fixed code • Rolling code DEFAULT FACTORY SETTINGS Restores all settings to the default factory settings. LANGUAGE SELECTION • Portuguese • English • Spanish OPENING DELAY TIME (WITH A TRAFFIC LIGHT) 8 Levels (without delay, 2 seconds, 4 seconds, 6 seconds, 8 seconds, 10 seconds, 12 seconds and 15 seconds). COMMAND ACTION DURING THE PAUSE TIME • Recharge: In this mode, if a command is generated during the closing temporization, the board interrupts the counting and restarts the set counting for closing. • Closing: In this mode, if a command is generated during the closing temporization, the board interrupts the counting and automatically starts the closing maneuver after the command received. CONTACT OF THE LIMIT SWITCH SENSORS • NC (normally closed) • NO (normally open) PHOTOCELL CONTACT • NC (normally closed) • NO (normally open) ERASE PATH Erases the path acquired by the control board. PUSHBUTTON (KIND OF CONTACT) • NC (normally closed) • NO (normally open) PUSHBUTTON (OPERATION) opening (Yes or No) Changes the 'BOT' output terminal of the board to a command (only for opening). (OPTIONAL) LOOSE RECEIVER RELAY MODULE FOR COURTESY LIGHT PROG RELAY MODULE FOR LOCK PROGRAMMING BUTTONS 127 VAC / 220 VAC (50Hz / 60 Hz) INDUCTION MOTOR (SINGLE-PHASE) STARTING CAPACITOR REEDS (LIMIT SWITCHES) TX RX PHOTOCELL M C C F A FCA FCF TACT LED P06623 - Rev. 0

LAYOUT A3 P06623 MANUAL CENTRAL AGILITY · AGILITY CONTROL BOARD TECHNICAL MANUAL PXXXXX - Rev. 0 WARNING without referring to this LEDs sinalization: • N1 lit = Function disabled

  • Upload
    others

  • View
    4

  • Download
    0

Embed Size (px)

Citation preview

Page 1: LAYOUT A3 P06623 MANUAL CENTRAL AGILITY · AGILITY CONTROL BOARD TECHNICAL MANUAL PXXXXX - Rev. 0 WARNING without referring to this LEDs sinalization: • N1 lit = Function disabled

MAIN FEATURES

• FullRangeACPowerSupply(90–240V);• AnalogLimitSwitchSystem;• RFreceiveron-board;• EEPromMemoryforstoringbothaddedremotecontrolsandthecontrolboardsetup;

• SetupbypushbuttonswitchesandeightlevelsbyLEDs;• Upto256remotecontrols;• Electronicclutch(strength)adjustment;• Automaticacquiring(O/Cpath);• Inputportsforphotocellandpushbutton;• Outputportsforreceiver,electriclockandcourtesylightmodules;

• Brakeadjustment;• Independentadjustmentofthetravelstopramp(openingandclosing);

• Presetopeningdelaywhenatrafficlightisused;• CompatiblewithPROG.

CHART: LED FUNCTIONS

GuideforthefunctionsoftheindicatorLEDsontheboard,whenitisnotinprogrammingmode,i.e.,'JPROG'jumperopen.

LED FUNCTION

MEM(N1)

• Lit:Emptymemory,withnoremotecontrolsadded.

• Blinking:Nomemoryorfaultymemory.Inthiscase,thecontrolboardentersthebasicoperationmode;itmeansthatfunctionssuchasexternalPROG,theprogrammingbuttonsandtheremotecontrolsgetdisabled.*

FOT(N2) • Lit:Photocelltriggered.

CMD(N3) • Lit:ExternalreceiverorCMDbuttonactivated.

BOT(N4) • Lit:Externalpushbuttonactivated.TX(N5) • Lit:Addedremotecontroldetected.FCA(N6) • Lit:Openlimitswitchtriggered.FCF(N7) • Lit:Closedlimitswitchtriggered.

SN(N8) • Blinkseverytwoseconds:Normaloperation.

*BASIC OPERATION MODECommandonlyenabledbyusinganexternalpushbutton,'CMD'buttonorexternalRFreceiver;commandduringopeningmanouvreenabled,clutchonthemaximumlevel;semi-automaticmode;rampsdisabled;commandforclosingduringthetimepause;CLSandOLS(CLS=ClosingLimitSwitch/OLS=OpeningLimitSwitch)sensorsNormallyopenandphotocellnormallyopen.

CHART: SETTING CONFIGURATIONS

Quickconfigurationguide.Inordertoenterprogrammingmode,onemustclosethe'JPROG'jumperontheboard.

BUTTON FUNCTIONTX AddoreraseremotecontrolsCMD CommandwhenopeningFORÇA Strength(Electronicclutch)PAUSA Automaticclosingtime

RAMPABABRE OpeningrampRAMPFCFECHA ClosingrampRAMPTORQTORQUE RampTorque(Strength)

FREIO BrakeLGGARAGEM Courtesylighttime

ERASING ALL REMOTE CONTROLS

Erasesandbootsthememoryinordertoaddnewremotecontrols.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;

3. Pressandreleasethe'TX'buttononthecontrolboard(once);

4. N5(TX)LEDmustremainlit;5. Pressthe'TX'buttononthecontrolboardandkeepitpressedfor10seconds;

6. N8LEDmustremainlit,indicatingthatallremotecontrolshavebeenerasedfromthememory;

7. Inordertofinish,openJPROGjumper.

ADDING REMOTE CONTROLS

Itaddsnewremotecontrolstothecontrolboard,sothattheycantriggerit.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'TX'button(once);4. N5(TX)LEDmustremainlit;5. Pressthebuttonoftheremotecontrolonewantsto

addandkeepitpressed;6. N8LEDmustremainblinking;7. N8LEDblinksonce(buttonalreadyadded),blinks

twice(buttonalreadyaddedandnewsynchronizationforaRollingCodeRemotecontrol)orthreetimes(memoryfull);

8. Pressandreleasethe'TX'buttonontheboardtoconfirmtheoperation;

9. Releasethebuttonoftheremotecontrol;10.Gobacktostep3toaddanewbuttonoftheremote

control;11. Inordertofinish,openJPROGjumper.

COMMAND DURING OPENING

Permissionforacommandfromeitherapushbuttonorremotecontroltobeacceptedduringtheopeningmaneuver.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'CMD'buttonontheboard(once);

4. Pressandreleasethe'CMD'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Functionenabled.• N2lit=Functiondisabled.

STRENGTH (ELECTRONIC CLUTCH)

Inordertoassuretheefficiencyofthissecuritysensordevice,proceedasfollows:-Afterproperlyinstallingthegateopener,adjusttheelectronicclutchsothatthestrengthnecessarytoacompletegatemaneuverisminimumwhenbothopeningandclosing.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'FORÇA'buttonontheboard(once);

4. Pressandreleasethe'FORÇA'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Minimum....• N8lit=Maximum.

SEMI-AUTOMATIC / AUTOMATIC MODE (PAUSE TIME)

ItisthetimeadjustmentfortheautomaticclosingwhenthegatereachestheOLSlimitswitchsensorortheopeningstop,indicatingthelimitoftheopeningmaneuver.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'PAUSA'buttonontheboard(once);

4. Pressandreleasethe'PAUSA'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Semi-automatic.• N2lit=30seconds.• N3lit=60seconds.• N4lit=90seconds.• N5lit=120seconds.• N6lit=150seconds.• N7lit=180seconds.• N8lit=240seconds.

OPENING RAMP

Itisthedistancebetweentheopeningmechanicalstopandthepointofthepathwheretheelectronicboardenterstorquecontrolmodeinordertodecreasethespeedofthegateandturntheopeneroffontheacquiredpath,i.e.,thedistanceinwhichtheopenerstartsdeceleratingwhenopeningthegate.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'RAMPABABRE'buttonontheboard(once);

4. Pressandreleasethe'RAMPABABRE'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Functiondisabled.• N2lit=5%ofthegatepath.• N3lit=10%ofthegatepath.• N4lit=15%ofthegatepath.• N5lit=20%ofthegatepath.• N6lit=25%ofthegatepath.• N7lit=30%ofthegatepath.• N8lit=35%ofthegatepath.

CLOSING RAMP

Itisthedistancebetweentheclosingmechanicalstopandthepointofthepathwheretheelectronicboardenterstorquecontrolmodeinordertodecreasethespeedofthegateandturntheopeneroffontheacquiredpath,i.e.,thedistanceinwhichtheopenerstartsdeceleratingwhenclosingthegate.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'RAMPABFECHA'buttonontheboard(once);

4. Pressandreleasethe'RAMPABFECHA'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

AGILITYCONTROL BOARD

TECHNICALMANUAL

PXXXXX-Rev.0

WARNINGDo not use the equipment without referring to this manual first.

LEDssinalization:• N1lit=Functiondisabled.• N2lit=5%ofthegatepath.• N3lit=10%ofthegatepath.• N4lit=15%ofthegatepath.• N5lit=20%ofthegatepath.• N6lit=25%ofthegatepath.• N7lit=30%ofthegatepath.• N8lit=35%ofthegatepath.

TORQUE (STRENGTH) ON THE RAMP

Thisadjustmentdecreasesthegatespeedwhenitiswithinthedecelerationramparea,i.e.,thestrengthofthegateopenerintheareaofthelimitswitchramp,closetothestopsofthegate.Incaseitisdisabled,thetorquecontrolontherampwillbeinoperative.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'RAMPTORQTORQUE'buttonontheboard(once);

4. Pressandreleasethe'RAMPTORQTORQUE'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Minimum....• N8lit=Maximum.

BRAKE

Itisactivatedwhenthemotoristurnedoffbyacommand,orwhentheopenerreachestheanalogsensors(limitswitches).

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'FREIO'buttonontheboard(once);

4. Pressandreleasethe'FREIO'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=Functiondisabled.• N2lit=Minimum....• N8lit=Maximum.

COURTESY LIGHT TIME

Itselectsthetimeinwhichthe“LUZ”outputwillremainactivatedafterthegatecloses.Duringtheopeningorclosingmaneuver,orwhenthegateisstillandopen,therelaymodulewillremainenabled.Whenthecontrolboardfinishestheclosingmaneuver,therelaymodulewillbedisabledafterthetimeset.

Instructions:1. Thegatemustbestill;2. CloseJPROGjumper;3. Pressandreleasethe'LGGARAGEM'buttonontheboard(once);

4. Pressandreleasethe'LGGARAGEM'asmanytimesasnecessaryuntilonereachesthedesiredadjustment;

5. Inordertofinish,openJPROGjumper.

LEDssinalization:• N1lit=10seconds.• N2lit=30seconds.• N3lit=60seconds.• N4lit=90seconds.• N5lit=120seconds.• N6lit=150seconds.• N7lit=180seconds.• N8lit=240seconds.

ERASING THE ACQUIRED PATH

Iterasesthepathofthegateopeneracquiredbythecontrolboard.

Instructions:1. Thegatemustbestill;2. KeepJPROGjumperopen;3. Pressthe'FREIO'buttonontheboardandkeepitpressed;

4. After8seconds,whenallLEDsstartblinking,releasethe'FREIO'button.

5. Sincethepathisnowerased,thecontrolboardwillacquireanewpath,andwillfinishthisstepafterreachingthetheopeningandclosingReed-switches;

NOTE:After8seconds,theLEDswillstartblinkingforapresettimeintervalandafterwardswillbeswitchedoff.

IMPORTANTIn case the button is released while the LEDs are blinking, the board will run the chosen operation. However, if the button remains pressed while the LEDs are blinking, and is only released after they are switched off, the board will both cancel the operation and automatically exit the operation mode.

DEFAULT FACTORY SETTINGS

Itrestoresthesettingstotheirdefeaultparameters.

Instructions:1. Thegatemustbestill;2. KeepJPROGjumperopen;3. Pressthe'RAMPTORQTORQUE'buttonontheboardandkeepitpressed;

4. After8seconds,whenallLEDsstartblinking,releasethe'RAMPTORQTORQUE'button.

5. Nowwiththedefaultfactorysettingsrestoredtotheboardandwiththepatherased,theboardwillacquireanewpath,andwillfinishthisstepafterreachingthetheopeningandclosingReed-switches;

NOTE:After8seconds,theLEDswillstartblinkingforapresettimeintervalandafterwardswillbeswitchedoff.

IMPORTANTIn case the button is released while the LEDs are blinking, the board will run the chosen operation. However, if the button remains pressed while the LEDs are blinking, and is only released after they are switched off, the board will both cancel the operation and automatically exit the operation mode.

'F/R' JUMPER

Itreversesthedirectionofrotationofthemotor,whatisopeningbecomesclosingandviceversa;italsoreversesthelogicofthelimitswitchsensors,OLSandCLS.

CHART: SETTING THROUGH 'PROG' (PROGRAMMING TOOL)

FUNCTION PARAMETERS

HOMESCREEN

Monitoresthesensorsandtheperipheralsoftheboard(OLS,CLS,pushbutton,photocell,remotecontrol,Statusoftheboardandtimers(Courtesylight,PauseandEletromagnecticlock))

ADDINGREMOTECONTROLS

Addnewremotecontrolstotheboard.

PAUSETIME • Semi-automatic• Timeforautomaticclosing

CLOSINGRAMP 8LevelsOPENINGRAMP 8LevelsSTRENGTH(ELECTRONICCLUTCH)

8Levels

COURTESYLIGHTTIME 8Levels

COMMANDWHENOPENING

• Enabled•Disabled

ELECTRONICBRAKETIME 8Levels

ERASEREMOTECONTROLS

Erasesallremotecontrolsaddedtotheboard.

TYPEOFREMOTECONTROL

• Fixedcode•Rollingcode

DEFAULTFACTORYSETTINGS

Restoresallsettingstothedefaultfactorysettings.

LANGUAGESELECTION

•Portuguese• English• Spanish

OPENINGDELAYTIME(WITHATRAFFICLIGHT)

8Levels(withoutdelay,2seconds,4seconds,6seconds,8seconds,10seconds,12secondsand15seconds).

COMMANDACTIONDURINGTHEPAUSETIME

•Recharge:Inthismode,ifacommandisgeneratedduringtheclosingtemporization,theboardinterruptsthecountingandrestartsthesetcountingforclosing.

•Closing:Inthismode,ifacommandisgeneratedduringtheclosingtemporization,theboardinterruptsthecountingandautomaticallystartstheclosingmaneuverafterthecommandreceived.

CONTACTOFTHELIMITSWITCHSENSORS

•NC(normallyclosed)•NO(normallyopen)

PHOTOCELLCONTACT

•NC(normallyclosed)•NO(normallyopen)

ERASEPATH Erasesthepathacquiredbythecontrolboard.

PUSHBUTTON(KINDOFCONTACT)

•NC(normallyclosed)•NO(normallyopen)

PUSHBUTTON(OPERATION)

opening(YesorNo)Changesthe'BOT'outputterminaloftheboardtoacommand(onlyforopening).

(OPTIONAL)LOOSERECEIVER

RELAYMODULEFORCOURTESYLIGHT

PROG

RELAYMODULEFORLOCK

PROGRAMMINGBUTTONS

127VAC/220VAC(50Hz/60Hz)

INDUCTIONMOTOR(SINGLE-PHASE)

STARTINGCAPACITOR

REEDS(LIMITSWITCHES)

TX

RX

PHOTOCELL

M

C CF A

FCAFCF

TACT

LED

P06623 - Rev. 0

Page 2: LAYOUT A3 P06623 MANUAL CENTRAL AGILITY · AGILITY CONTROL BOARD TECHNICAL MANUAL PXXXXX - Rev. 0 WARNING without referring to this LEDs sinalization: • N1 lit = Function disabled

PRINCIPALES CARACTERÍSTICAS

• AlimentaciónFullRange(90–240);• SistemadeFindeCarreraAnalógico;• Receptorderadiofrecuencia(RF)incorporadoalaplacadelacentral;

• MemoriaEEPromparaalmacenamientodeloscontrolesremotosyprogramacióndelacentralelectrónica;

• ProgramaciónporpulsadoresswitchyochonivelesporLEDs;

• Capacidadparahasta256controlesremotos;• Ajustedeembragueelectrónico(fuerza);• AprendizajeautomáticodelrecorridoApertura/Cierre;• EntradasparafotocélulayPulsadordepared(botonera);• Salidasparareceptor,módulosdeelectrocerradurayluzdecortesía;

• Ajustedefreno;• Ajustederampadefindecarreraseparado(aperturaycierre);

• Tiempoderetardoparaaperturaconsemáforo;• CompatibleconPROG;

TABLA DE FUNCIONES DE LEDs

GuíadefuncionesdelosLEDsdelacentral,cuandonoestáenmododeprogramación,coneljumperJPROGabierto.

LED FUNCIÓN

MEM(N1)

• Encendido:Memoriavacía,sincontrolesremotosañadidos.

• Parpadeando:Memórianoencontradaodefectuosa.Entalcaso,lacentralentraenmododefuncionamientobásico,desactivandolasfuncionesdelPROGexterno,elconjuntodebotonesdeprogramaciónyloscontrolesremotos.*

FOT(N2) • Encendido:Fotocélulaaccionada.

CMD(N3) • Encendido:Receptorexternoobotón'CMD'accionado.

BOT(N4) • Encendido:Botoneraexternaaccionada.

TX(N5) • Encendido:Controlremotoañadidopresente.

FCA(N6) • Encendido:Findecarreradeaperturaaccionado.

FCF(N7) • Encendido:Findecarreradecierreaccionado.

SN(N8) • Parpadeoscada2segundos:Funcionamientonormal.

*MODO DE FUNCIONAMIENTO BÁSICOComandosolamenteporlabotoneraexterna,botón'CMD'oreceptorRFexterno;comandoduranteaperturahabilitado;embragueenmáximo;modosemiautomático;rampasdeshabilitadas;comandoparacierreduranteeltiempodepausa;sensoresFCCyFCA(FindeCarreraCerradoyFindeCarreraAbierto)comoNA(normalmenteabierto)yfotocélulaNA.

TABLA DE COMANDO PARA CONFIGURACIONES

Guiarápidadeconfiguraciones,paraentrarenelmododeprogramacióndelacentralelectrónica,sedebecerrareljumperJPROGdelaplaca.

BOTÓN FUNCIÓNTX AãndiroBorrarControlesRemotosCMD ComandoenlaAperturaFORÇA Fuerza(EmbragueElectrónico)PAUSA TiempodeCierreAutomático

RAMPABABRE RampadeAperturaRAMPFCFECHA RampadeCierreRAMPTORQTORQUE Torque(Fuerza)enlaRampa

FREIO FrenoLGGARAGEM TiempodeLuzdeCortesía

BORRAR TODOS LOS CONTROLES REMOTOS

Borraeinicializalamemoriaparaañadirnuevoscontrolesremotos.

Instrucciones:1. Elportóndebeestarparado;2. Cierrejumper'JPROG';3. Aprieteysuelteelbotón'TX'delacentral(1vez);4. LED'N5'(TX)debequedarencendido;5. Aprieteymantengaapretadoelbotón'TX'delacentralpor10segundos;

6. LED'N8'debequedarencendido,indicandoquehaborradotodosloscontrolesremotos;

7. Parafinalizar,quiteeljumperde'JPROG'.

AÑADIR CONTROLES REMOTOS

Agreganuevoscontrolesremotosenlacentraldecomando,paraqueellospuedancontrolarelautomatizador.

Instrucciones:1. Elportóndebeestarparado;2. Cierrejumper'JPROG';3. Aprieteysuelteelbotón'TX'delacentral(1vez);4. LED'N5'(TX)debequedarencendido;5. Aprieteymantengaapretadoelbotóndelcontrol

remotoquedeseaañadir;6. LED'N8'debeparpadear;7. LED'N8'parpadea1vez(botóndelcontrolremoto

añadido),parpadea2veces(botóndelcontrolremotoyaañadidoynuevasincronizaciónparacontrolcódigorodante)o3veces(memoriallena);

8. Aprieteysuelteelbotón'TX'delacentralparaconfirmarlaoperación;

9. Suelteelbotóndelcontrolremoto;10.Vuelvaalpaso3paraañadirunnuevobotóndel

controlremoto;11. Parafinalizar,quiteeljumperde'JPROG'.

COMANDO EN LA APERTURA

Permisodecomandoparaqueunabotoneraocontrolremotofuncionenduranteunamaniobradeaperturadelportón.

Instrucciones:1. Elportóndebeestarparado;2. Cierrejumper'JPROG';3. Aprieteysuelteelbotón'CMD'delacentral(1vez);4. Aprieteysuelteelbotón'CMD'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Funciónhabilitada.• N2encendido=Funcióndeshabilitada.

FUERZA (EMBRAGUE ELECTRÓNICO)

Paralautilizacióndeestedispositivosensordeseguridadsereficaz,sigaestespasos:-Traslacorrectainstalacióndelautomatizador,ajusteelembragueelectrónicodemodoquelafuerzautilizadasealamínimanecesariaparamoverelportóncompletamente,tantoenlaaperturacomoenelcierre.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'FORÇA'delacentral(1vez);4. Aprieteysuelteelbotón'FORÇA'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperdeJPROG.

SeñalizacionesdelosLEDs:• N1encendido=Mínimo....• N8encendido=Máximo.

SEMIAUTOMÁTICO / MODO AUTOMÁTICO (TIEMPO DE PAUSA)

AjustedetiempoparacierreautomáticocuandoelportónalcanzaelsensorfindecarreradeaperturaFCAoeltopedeapertura,indicandoelfindelaapertura.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'PAUSA'delacentral(1vez);4. Aprieteysuelteelbotón'PAUSA'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Semiautomático.• N2encendido=30segundos.• N3encendido=60segundos.• N4encendido=90segundos.• N5encendido=120segundos.• N6encendido=150segundos.• N7encendido=180segundos.• N8encendido=240segundos.

RAMPA DE APERTURA

Esladistanciaentreeltopemecánicodeaperturayelpuntodelrecorridodedondelacentralentraenmododetorquepulsanteparareducirlavelocidaddelportónyapagarenelrecorridoalmacenado,esdecir,ladistanciaenqueelautomatizadorempiezaadesacelerarenlaaperturadelportón.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'RAMPABABRE'delacentral(1vez);

4. Aprieteysuelteelbotón'RAMPABABRE'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Funcióndeshabilitada.• N2encendido=5%delrecorrido.• N3encendido=10%delrecorrido.• N4encendido=15%delrecorrido.• N5encendido=20%delrecorrido.• N6encendido=25%delrecorrido.• N7encendido=30%delrecorrido.• N8encendido=35%delrecorrido.

RAMPA DE CIERRE

Esladistanciaentreeltopemecánicodecierreyelpuntodelrecorridodedondelacentralentraenmododetorquepulsanteparareducirlavelocidaddelportónyapagarenelrecorridoalmacenado,esdecir,ladistanciaenqueelautomatizadorempiezaadesacelerarenelcierredelportón.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';

CENTRAL

AGILITYMANUALTÉCNICO

PXXXXX-Rev.0

ADVERTENCIANo utilice el equipo sin antes leer este manual de instrucciones. COMODIDAD Y SEGURIDAD

3. Aprieteysuelteelbotón'RAMPFCFECHA'delacentral(1vez);

4. Aprieteysuelteelbotón'RAMPFCFECHA'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Funcióndeshabilitada.• N2encendido=5%delrecorrido.• N3encendido=10%delrecorrido.• N4encendido=15%delrecorrido.• N5encendido=20%delrecorrido.• N6encendido=25%delrecorrido.• N7encendido=30%delrecorrido.• N8encendido=35%delrecorrido.

TORQUE (FUERZA) EN LA RAMPA

Esteajustedisminuyelavelocidaddelportóncuandoelrecorridoestédentrodelaregiónderampadedeceleración,esdecir,la“fuerza”delautomatizadorenlaregiónderampadefindecarrera,cercadelospuntosdeparadadelportón.Silarampaesdeshabilitada,eltorquepulsanteenlarampaquedainoperante.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'RAMPTORQTORQUE'delacentral(1vez);

4. Aprieteysuelteelbotón'RAMPTORQTORQUE'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Mínimo....• N8encendido=Máximo.

FRENO

Esaccionadoalapagarelmotorporcomando,oalalcanzarlossensoresanalógicos(finalesdecarrera).

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'FREIO'delacentral(1vez);4. Aprieteysuelteelbotón'FREIO'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quiteeljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=Funcióndeshabilitada.• N2encendido=Mínimo....• N8encendido=Máximo.

TIEMPO DE LUZ DE CORTESÍA

Seleccionaeltiempoenquelasalida“LUZ”quedaaccionadatraselcierredelportón.Durantelaaperturaocierredelportónocuandoelportónestáparadoabierto,elmódulodereléquedaencendido.Cuandolacentralfinalizaelcierre,elmódulodereléesapagadotraseltiempoprogramado.

Instrucciones:1. Elportóndebeestarparado;2. Cierreeljumper'JPROG';3. Aprieteysuelteelbotón'LGGARAGEM'delacentral(1vez);

4. Aprieteysuelteelbotón'LGGARAGEM'tantasvecescomoseanecesario,hastaqueencuentreelajustedeseado;

5. Parafinalizar,quitareljumperde'JPROG'.

SeñalizacionesdelosLEDs:• N1encendido=10segundos.• N2encendido=30segundos.• N3encendido=60segundos.• N4encendido=90segundos.• N5encendido=120segundos.• N6encendido=150segundos.• N7encendido=180segundos.• N8encendido=240segundos.

BORRANDO EL RECORRIDO

Borraelrecorrido(trayecto)delautomatizadoralmacenadoporlacentral.

Instrucciones:1. Elportóndebeestarparado;2. Mantengaeljumper'JPROG'abierto;3. Aprieteymantengaapretadoelbotón'FREIO'delacentral;

4. Tras8segundos,cuandotodoslosLEDsempiezanaparpadear,suelteelbotón'FREIO'.

5. Yaqueelrecorridoestáborrado,lacentralalmacenaráunnuevorecorrido,yfinalizaráestepasotrasalcanzarlossensoresREEDdeaperturaycierre;

NOTA:Tras8segundos,losLEDsempiezanaparpadearenundeterminadointervalodetiempoydespuésseapagan.

IMPORTANTESi el botón es suelto mientras los LEDs estén parpa-deando, la central realiza la operación elegida. Pero si se mantiene el botón apretado durante el tiempo en que los LEDs quedan parpadeando y solamente sea suelto después que los LEDs apagan, la central cancela la operación y sale del modo de programa-ción automáticamente.

CONFIGURACIÓN PREDETERMINADA DE FÁBRICA

Restablecelasconfiguracionesparalosvaloresdefábrica.

Instrucciones:1. Elportóndebeestarparado;2. Mantengaeljumper'JPROG'abierto;3. Aprieteymantengaapretadoelbotón'RAMPTORQTORQUE'delacentral;

4. Tras8segundos,cuandotodoslosLEDsempiezanaparpadear,suelteelbotón'RAMPTORQTORQUE'.

5. Yaconosvaloresdefábricacargadosenlaplacayconelrecorridoborrado,lacentralalmacenaráunnuevorecorrido,yfinalizaráestepasotrasalcanzarlossensoresREEDdeaperturaycierre;

OBS:Tras8segundos,losLEDsempiezanaparpadearenundeterminadointervalodetiempoydespuésseapagan.

IMPORTANTESi el botón es suelto mientras los LEDs estén parpa-deando, la central realiza la operación elegida. Pero si se mantiene el botón apretado durante el tiempo en que los LEDs quedan parpadeando y solamente sea suelto después que los LEDs apagan, la central cancela la operación y sale del modo de programa-ción automáticamente.

JUMPER F/R

Invierteelsentidoderotacióndelmotor;loqueesaperturaseconvierteencierreyviceversa,ytambiéninviertelalógicadelossensoresdefindecarrera,FCAyFCC.

TABLA DE CONFIGURACIÓN POR EL ACCESORIO DE PROGRAMACIÓN “PROG”

FUNCIÓN PARÁMETROS

PANTALLAPRINCIPAL

Monitoreodelossensoresydelosperiféricosdelacentral(FCA,FCC,Botonera,Fotocélula,Controlremoto,StatusdelaCentralyTemporizadores(LuzdeCortesía,Pausayelectrocerradura)

AÑADIRCONTROLESREMOTOS

Agreganuevoscontrolesremotosenlacentral.

TIEMPODEPAUSA •Semiautomático• Tiempoparacierreautomático

RAMPADECIERRE 8NivelesRAMPADEAPERTURA 8Niveles

FUERZA(EMBRAGUEELECTRÓNICO) 8Niveles

TIEMPODELUZDECORTESÍA 8Niveles

COMANDOENLAAPERTURA

•Habilitado•Deshabilitado

TIEMPODELFRENOELECTRÓNICO 8Niveles

BORRARCONTROLESREMOTOS

Borratodosloscontrolesremotosalmacenadosenlacentral.

TIPODECONTROLESREMOTOS

•CódigoFijo•CódigoRodante

CONFIGURACIÓNPREDETERMINADADEFÁBRICA

Restablecelasconfiguracionesparalosvaloresdefábrica.

SELECCIÓNDELIDIOMA

•Portugués• Inglés• Español

TIEMPODERETARDOENLAAPERTURACONSEMÁFORO

8Niveles(sinretardo,2segundos,4segundos,6segundos,8segundos,10segundos,12segundosy15segundos).

ACCIÓNDELCOMANDODURANTEELTIEMPODEPAUSA

•Recarga:Enestemodo,siuncomandoesgeneradoduranteelconteodetiempoparacierre,lacentralinterrumpeelconteoyvuelveacontareltiempoprogramadoparacerrar.

•Cierre:Enestemodo,siuncomandoesgeneradoduranteelconteodetiempoparacierre,lacentralinterrumpeelconteoeimpiezaelcierreautomáticamentetraselcomandorecibido.

CONTACTODELOSSENSORESDEFINDECARRERA

•NC(normalmentecerrado)•NA(normalmenteabierto)

CONTACTODELAFOTOCÉLULA

•NC(normalmentecerrado)•NA(normalmenteabierto)

BORRARELRECORRIDO

Borraelrecorridoalmacenadoenlacentraldecomando.

BOTONERA(TIPODECONTACTO)

•NC(normalmentecerrado)•NA(normalmenteabierto)

BOTOEIRA(FUNCIONAMENTO)

Apertura(SíoNo)Cambiaelborne"BOT"delacentralencomandoparaaperturasolamente.

RECEPTORSUELTO(OPCIONAL)

MÓDULORELÉPARALUZDECORTESÍA

PROG

MÓDULORELÉPARAELECTROCERRADURA

BOTONESDEPROGRAMACIÓN

127VAC/220VAC(50Hz/60Hz)

MOTORDEINDUCCIÓNMONOFÁSICO

CAPACITORDEARRANQUEDEL

MOTOR

REEDSDEFINDECARRERA

TX

RX

FOTOCÉLULA

M

C CF A

FCAFCF

TACT

LED

P06623 - Rev. 0

Agility SalesCollateral CountryProfile...Agility Oman is a leader in project logistics, contract logistics and customs brokerage. Leveraging the global Agility network, Agility Oman

Agility SalesCollateral CountryProfile...Agility Oman is a leader in project logistics, contract logistics and customs brokerage. Leveraging the global Agility network, Agility Oman

Documents
Referring expression & arguments

Referring expression & arguments

Education
Agility SalesCollateral CountryProfile - Agility Logistics

Agility SalesCollateral CountryProfile - Agility Logistics

Documents
WORCESTER AGILITY SOCIETY · Championship Agility, Premier Agility , Open Agility or Limited Agility Shows (i.e. special classes and invitational events excepted). Only a first place

WORCESTER AGILITY SOCIETY · Championship Agility, Premier Agility , Open Agility or Limited Agility Shows (i.e. special classes and invitational events excepted). Only a first place

Documents
Discussing Options and Referring Adolescents to Treatment Options and Referring... · Discussing Options and Referring Adolescents to Treatment ... also review unique challenges that

Discussing Options and Referring Adolescents to Treatment Options and Referring... · Discussing Options and Referring Adolescents to Treatment ... also review unique challenges that

Documents
speed & agility training for soccer - Tucson Soccer Academy AGILITY TRAINING... · SPEED & AGILITY TRAINING FOR SOCCER The application of speed and agility training specifically for

speed & agility training for soccer - Tucson Soccer Academy AGILITY TRAINING... · SPEED & AGILITY TRAINING FOR SOCCER The application of speed and agility training specifically for

Documents
FOCUSED, FAST & FLEXIBLEagilityconsulting.com/wp-content/uploads/2016/03/Mini...FOCUSED, FAST & FLEXIBLE Organizational Agility Agility Leadership Agility Analytics T eam Agility Most

FOCUSED, FAST & FLEXIBLEagilityconsulting.com/wp-content/uploads/2016/03/Mini...FOCUSED, FAST & FLEXIBLE Organizational Agility Agility Leadership Agility Analytics T eam Agility Most

Documents
Occupational Health and Safety NOISE HAZARDS IN THE WORKPLACE Presented by: Erin, Lxxx, Lxxx, Rxxxxxx, Pxxxxx

Occupational Health and Safety NOISE HAZARDS IN THE WORKPLACE Presented by: Erin, Lxxx, Lxxx, Rxxxxxx, Pxxxxx

Documents
Cross-Modal Relationship Inference for Grounding Referring ... · referring expressions [9, 23] is a fundamental one. Ground-ing referring expressions attempts to locate the target

Cross-Modal Relationship Inference for Grounding Referring ... · referring expressions [9, 23] is a fundamental one. Ground-ing referring expressions attempts to locate the target

Documents
Referring for Evaluation

Referring for Evaluation

Education
Inject agility back in your organization Inject agility

Inject agility back in your organization Inject agility

Documents
Competencies of PRODUCT OWNERS · CUSTOMER AGILITY 12 RESULTS AGILITY 14 MENTAL AGILITY 17 CHANGE AGILITY 18 INNOVATION AGILITY 20 SYSTEMS AGILITY 21 ABOUT US 25. 3 INTRODUCTION The

Competencies of PRODUCT OWNERS · CUSTOMER AGILITY 12 RESULTS AGILITY 14 MENTAL AGILITY 17 CHANGE AGILITY 18 INNOVATION AGILITY 20 SYSTEMS AGILITY 21 ABOUT US 25. 3 INTRODUCTION The

Documents
Political Verse in Late Georgian Britain:Poems Referring ... · Political Verse in Late Georgian Britain:Poems Referring to William ... in Late Georgian Britain:Poems Referring to

Political Verse in Late Georgian Britain:Poems Referring ... · Political Verse in Late Georgian Britain:Poems Referring to William ... in Late Georgian Britain:Poems Referring to

Documents
SUFFOLK FIVE RIVERS AGILITY CLUB · onship Agility, Premier Agility, Open Agility or Limited Agility Shows (i.e. special classes and invitational events excepted). Only a first place

SUFFOLK FIVE RIVERS AGILITY CLUB · onship Agility, Premier Agility, Open Agility or Limited Agility Shows (i.e. special classes and invitational events excepted). Only a first place

Documents
Peering into Team-Agility & Talent-Agility- A New Tool for HRagilityconsulting.com/.../06/Peering-into-Team-Agility-Talent-Agility-A... · Peering into Team-Agility & Talent-Agility:

Peering into Team-Agility & Talent-Agility- A New Tool for HRagilityconsulting.com/.../06/Peering-into-Team-Agility-Talent-Agility-A... · Peering into Team-Agility & Talent-Agility:

Documents
To earn extra income by referring, just keep on referring to this

To earn extra income by referring, just keep on referring to this

Documents
IV Referring Physician Form - Northwest Natural Healthnwnaturalhealth.com/_documents/IV-Referring-Physician-Form.pdf · Referring Physician Form for IV Nutrition Therapy For providers

IV Referring Physician Form - Northwest Natural Healthnwnaturalhealth.com/_documents/IV-Referring-Physician-Form.pdf · Referring Physician Form for IV Nutrition Therapy For providers

Documents
AS A Agility: NE Ohio’s est Kept Agility Secret

AS A Agility: NE Ohio’s est Kept Agility Secret

Documents
PRAGMATICS-REFERRING EXPERESSIONS

PRAGMATICS-REFERRING EXPERESSIONS

Documents
Gamified agility

Gamified agility

Technology
Referring to the Text

Referring to the Text

Documents
Leadership Agility: A Business Imperative for a …agilityconsulting.com/resources/Agility Leader/Leadership Agility...Leadership Agility: A Business Imperative for a VUCA World By

Leadership Agility: A Business Imperative for a …agilityconsulting.com/resources/Agility Leader/Leadership Agility...Leadership Agility: A Business Imperative for a VUCA World By

Documents
Central Virginia Agility Club AKC Sanctioned Agility Trial

Central Virginia Agility Club AKC Sanctioned Agility Trial

Documents
Business Intelligence Agility, Informing Agility and

Business Intelligence Agility, Informing Agility and

Documents
Organizational agility

Organizational agility

Business
Strawson, P. —On Referring

Strawson, P. —On Referring

Documents
Assessing Your Agility: Introducing the Comparative Agility Assessment

Assessing Your Agility: Introducing the Comparative Agility Assessment

Business
Referring others

Referring others

Healthcare
Agility Consulting - Business Agility Institute · Leadership Agility Profile 360 –Fitness Diagnostic Agility Consulting 2017 Business Agility Conference 8. CEO of REI and Secretary

Agility Consulting - Business Agility Institute · Leadership Agility Profile 360 –Fitness Diagnostic Agility Consulting 2017 Business Agility Conference 8. CEO of REI and Secretary

Documents
Integrity - Agility - Value VSE Corporation Integrity - Agility - Value 1

Integrity - Agility - Value VSE Corporation Integrity - Agility - Value 1

Documents