Laboratory Name GM GAUGING SOLUTIONS, 23,NEELKANTH …

S.No Discipline / Group Quantity Measured/Instrument

Range / Frequency * CalibrationMeasurementCapability(±)

Remarks

Permanent Facility

1 MECHANICAL-DIMENSION (BASICMEASURINGINSTRUMENT,GAUGE ETC.)

Bevel Protector /Degree Protector L.C :1 min

0 Degree to 360Degree

2Minutes Using Angle Gauge Setby Comparison method


Bore Gauge (Transmission Error)L.C : 0.001 mm

0 mm to 1.2 mm 2.60micron Using Electronic DialCalibration Tester byComparison Method


Caliper (Vernier / Dial /Digital ) L.C :0.01 mm

0 mm to 600 mm 11.00micron Using CaliperChecker,SlipGauge,Granite SurfacePlate


Coating ThicknessGauge

0 mm to 4 mm 11.14micron Using Foils byComparison Method


Combination SetL.C : 1min / 30 Min


37Minutes Using Angle Gauge Setby Comparison method


Depth Micrometer L.C :0.001 mm

0 mm to 150 mm 8.0micron Using Slip Gauge Set

This is annexure to 'Certificate of Accreditation' and does not require any signature.

Laboratory Name GM GAUGING SOLUTIONS, 23,NEELKANTH SOCIETY,BEHIND SWATI SOCIETY,NEW SAMA ROAD, VADODARA, GUJARAT , INDIA

Accreditation Standard ISO/IEC 17025:2017

Certificate Number CC-2004 Page No. : 1 / 9

Validity 27/02/2019 to 26/02/2021 Last Amended on -



Remarks


Dial Indicator(LeverType)L.C:0.01 mm

0 mm to 0.8 mm 6.40micron Using Electronic DialCalibration Tester


Dial Indicator (LeverType)L.C : 0.001 mm

0 mm to 0.14 mm 2.80micron Using Electronic DialCalibration Tester ,Probe with DRO byComparison Method


Dial Indicator (LeverType)L.C : 0.002 mm

0 mm to 0.2 mm 2.70micron Using Electronic DialCalibration Tester ,Probe with DRO byComparison Method


Dial Indicator (PlungerType)L.C : 0.001 mm

0 mm to 25 mm 2.58micron Using Electronic DialCalibration Tester ,Using Slip Gauge Set ,Granite Surface Plateby Comparison Method


Dial ThicknessGaugeL.C :0.001 mm

0 mm to 30 mm 1micron Using Slip Gauge Set


External MicrometerL.C:0.001 mm









Remarks


External MicrometerL.C : 0.001 mm

100 to 200 mm 2.30micron Using Slip Gauge Set


External MicrometerL.C : 0.001 mm



Feeler Gauge 0.02 mm to 2 mm 3.50Micron Using DigitalMicrometer byComparison Method


Foils 0 mm to 2 mm 3.50Micron Using Electronic probewith DRO andcomparator standcomparison Method.


Height Block 10 mm to 150 mm 2.30micron Using Slip Gauge Set &Probe with DRO bycomparison method


Height GaugeL.C : 0.01mm

0 mm to 600 mm 11.00micron Using Caliper Checker, Granite Surface Plate








Remarks


Master Setting Disc 3 mm to 150 mm 2.30micron Using Slip Gauge Set &Probe with DRO bycomparison method


Measuring Pin Gauge 0.5 mm to 20 mm 1.80micron Using Slip Gauge Set &Probe with DRO bycomparison method


Measuring Tape 0 meter to 50 meter 130vL/1000(L inmm)micron

Using Tape & Scalecalibrator byComparison Method


Micrometer Setting Rod Up to 275 mm to null 3.0micron Using Slip gauge Set &Probe with DRO byComparison method


Paddle Gauge 0 mm to 300 mm 2.30micron Using Slip Gauge Set &Probe with DRO bycomparison method


Pi Tape Up to 6300 (Dia) mm tonull

130vL/1000(L inmm)micron

Using Tape & Scalecalibrator byComparison Method








Remarks


Pistol Caliper L.C : 0.10mm



Plain Plug Gauge 0 mm to 300 mm 2.16micron Using Slip Gauge Set &Probe with DRO bycomparison method


Radius Gauge R 0..5 mm to R 25 mm 12.5micron Using Profile Projector


Snap Gauge 1 mm to 150 mm 5.1micron Using Slip Gauge Set


Steel Scale L.C:0.5 mm 0 mm to 1000 mm 90.00micron Using Tape & Scalecalibrator byComparison Method


Taper Thread PlugGauge ( EffectiveDiameter)

1.6 mm to 100 mm 3.4micron UsingFCDM,CylindricalSetting Master andThread Measuring Wireby comparison method








Remarks


Thread measuring Wire 0.1 mm to 6.55 mm 1.60micron Using Slip Gauge Set &Probe with DRO bycomparison method


Thread Pitch Gauge Pitch length up to 6.35mm to null

18.00micron Using Profile Projector


Thread Plug Gauge (Effective and MajorDiameter)

2 mm to 100 mm 3.4micron UsingFCDM,CylindricalSetting Masters andThread measuring Wireby comparison method


Ultrasonic ThicknessGauge

0 mm to 200 mm 10.93micron Using Height Blocks byComparison Method


Vernier DepthGaugeL.C : 0.01 mm

0 mm to 300 mm 8.9micron Using Slip Gauge Set,CaliperChecker,GraniteSurface Plate bycomparison method


WeldGaugeAngularL.C :60Minutes

0 Degree to 60 Degree 7.33Minutes Using Profile Projectorby Comparison Method








Remarks


Weld GaugeLinearMeasurementL.C :1mm

0 mm to 60 mm 59.34micron Using Profile Projectorand Slip Gauge Set byComparison Method: --Select--


Width Gauge 1 mm to 150 mm 2.50micron Using Slip Gauge Set &Probe with DRO bycomparison method

39 MECHANICAL-DIMENSION(PRECISIONINSTRUMENTS)

Profile ProjectorAngularL.C :1 minute


2.4Minute Using Angle Gauge Set


Profile ProjectorLinearL.C :0.001 mm

0 mm to 300 mm 11.00micron Using Precision GlassScale


Profile ProjectorMagnification

10X to 50X 1.8% Using Slip Gauge andDigital Caliper

42 MECHANICAL-PRESSUREINDICATING DEVICES

Hydraulic Pressure (Analog / Digital )Gauges

0 bar to 35 bar 0.30bar Using Digital PressureGauge by ComparisonMethod as per DKD-R-6-1



0 bar to 400 bar 1.47bar to bar Using Digital PressureGauge by ComparisonMethod as per DKD-R-6-1








Remarks











Remarks

Site Facility


Profile ProjectorAngularL.C :1 minute


2.4Minute Using Angle Gauge Set


Profile ProjectorLinearL.C :0.001 mm

0 mm to 300 mm 11.00micron Using Precision GlassScale


Profile ProjectorMagnification

10X to 50X 1.8% Using Slip Gauge andDigital Caliper






0 bar to 400 bar 1.47bar to bar Using Digital PressureGauge by ComparisonMethod as per DKD-R-6-1









Documents

Laboratory Name GM GAUGING SOLUTIONS, 23,NEELKANTH …