Upload
mina-iskander
View
220
Download
0
Embed Size (px)
Citation preview
8/3/2019 Kalus Multi Parking - Turntable Datasheet
http://slidepdf.com/reader/full/kalus-multi-parking-turntable-datasheet 1/4
CONFORMITY
Klaus Multiparking GmbHHermann-Krum-Straße 2D-88319 Aitrach
Phone +49-7565-508-0
Fax +49-7565-508-88
E-Mail [email protected] www.multiparking.com
ge 1
ction
mensions
r data
ge 2
cessns
ge 3
ctricalta
chnicalta
ge 4
be perfor-d by the
stomer
scription
Page 1 of 4
T u r n t a b l e D 4 5 0 | C o d e n u m b e r 5 8 3 . 9 1 . 7 4 0 - 0 0 2 |
V e r s i o n 1 0 . 2 0 0 9
Product Data
Turntable
D450
Dimensions:
All space requirements are minimumfinished dimensions. Tolerances for spacerequirements . Dimensions in cm.+3
0 3 2 .
5
Turntable: Ø 450
Center bearing; dowelled;length of dowel: 10 cm
Required space: min. Ø 550 (in case of vehicle length 500 )
Drive unit 0.37 kW80
1 0
Drainage Ø 4
Conduit EN 25 (M25) with taut wire
Fixed part
Turning part
Top edgefinishedfloor
Turntable D450 (below floor level)
Turntable D450 (above floor level)
2 2 .
5
80
1 0
Top edgefinishedfloor
Top edge finished floor:Tolerances for the evenness of thecarriageway must be strictly compliedwith in accordance with DIN (= GermanIndustrial Standard) No. 18202, chart 3,line 3.
max. 5.00 mwidth
Car dimensions
max. 2500 kg weight
max. 625 kg wheel load
Suitable for:Standard passenger car and station wagon.
Standard passenger cars are vehicleswithout any sports options such asspoilers, low-profile tyres etc.
8/3/2019 Kalus Multi Parking - Turntable Datasheet
http://slidepdf.com/reader/full/kalus-multi-parking-turntable-datasheet 2/4
Turntable D450 | Code number 583.91.740-002 | Version 10.2009
ge 1
ction
mensions
r data
ge 2
cessns
ge 3
ctricalta
chnicalta
ge 4
be perfor-d by the
stomer
scription
Page 2 of 4
Recess plan for turntables with drive unit above floor level
Recess plan for turntables with drive unit below floor level
3 2 ,
5
480
80
1 0
Conduit EN 25 (M25) with taut wire
Drainage Ø 4
2 0
4 0
4 8 0
1 9 9
Drainage Ø 4
ConduitEN 25 (M25)with taut wire
+ 1 ,
5 + 1 ,
5
5 0
2 2 .
5
80
1 0
Conduit EN 25 (M25) with taut wire
Drainage Ø 4
1 0
+ 1 .
5
For turntables above floor level only the shaft for the drive unit is required (80 x 50 x 22.5 )
8/3/2019 Kalus Multi Parking - Turntable Datasheet
http://slidepdf.com/reader/full/kalus-multi-parking-turntable-datasheet 3/4
Turntable D450 | Code number 583.91.740-002 | Version 10.2009
ge 1
ction
mensions
r data
ge 2
cessns
ge 3
ctricalta
chnicalta
ge 4
be perfor-d by the
stomer
scription
Page 3 of 4
Technical data
– maintenance offer/contract– declaration of conformity
Available documents
Environmental conditions for the area of multiparking systems:Temperature range –10 to +40° C. Relative humidity 50 % at amaximum outside temperature of + 40° C.
Environmental conditions
See separate sheet regarding corrosion protection.
Corrosion protection
Ball bearing of the rollers provide a low sound level.
Noise emission
Electrical data
– Supply line 5 x 1.5 mm2 ( 3 PH+ N+ PE) to the main cabinet withlockable main switch. It is possible, that special laying systemand big length of the cable necessitate larger cable. The electricinstallation must correspond to the local standards.
– Main fuse:3 x fuse 10 A (slow) or circuit breaker 3 x 10 A (trigger characteristicK or C).
– The supply line to the main cabinet must be provided by thecustomer during installation. The functionality can be monitoredon site by our fitters together with the electrician. If this cannotbe done during installation for some reason for which the customeris responsible, the customer must commission an electrician attheir own expense and risk.
Electrical supply
Easy-to-survey positioning (e.g. on column).
Protection against unauthorized use.
May also be recessed in wall if required.
Operating device
– Max. load: cars and small trucks up to 2,500 kg
– It is prohibited to work on vehicles that are currently parked onthe turntable
– The parked vehicle must be protected against unintentionalmovement, in accordance to the operating instructions
– The transport of any persons on the turntable is only permittedwhen seated inside the vehicle
Notes
8/3/2019 Kalus Multi Parking - Turntable Datasheet
http://slidepdf.com/reader/full/kalus-multi-parking-turntable-datasheet 4/4
Turntable D450 | Code number 583.91.740-002 | Version 10.2009
ge 1
ction
mensions
r data
ge 2
cessns
ge 3
ctricalta
chnicalta
ge 4
be perfor-d by the
stomer
scription
Page 4 of 4
Description
We reserve the right to change this specification without further notice
The rotor consists of individual segments that are screwed togetherto form a solid frame. This frame is equipped with central ball bearingsand (in accordance to the static requirements for coverage) maintenance-free rollers with ball bearings, which allow low-noise movement of theturntable.
These rollers are placed on the circular U-profile frame, which is mountedsecurely to the floor using dowelled joints. Additional concrete bracketsare welded to the sides.
General description
– The turntable is driven by a three-phase geared motor using frictionalresistance ( 0.37 kW, IP 55, 400 V, 50 Hz)
– In 45 seconds, the table rotates 1 x 360° (n = 1.33/min)– In the event of a power failure, the turntable can be rotated manually
by releasing the motor brake– The motor is supported in a special compensator with adjustable
contact pressure– Specifications regarding the enclosure size for the motor and the
ductwork that must be setup by the customer can be foundon page 2
Drive
– A push-button is used for operation in dead man’s control– The power feed supplied by the customer can be interrupted
using a lockable main switch
Operation
– The floor cover is made of galvanized corrugated sheet metal– A cover is built-in at the appropriate location for installation andmaintenance work
– Screws, nuts and plates are galvanized– All other steel and sheet metal parts are hot-galvanized with
exception of construction-related parts such as bolts, bearings, etc.
Floor cover
– The weight of the entire turntable is approximately 1,500 kg– The turntable has a diameter of 450 cm
Weight
– 2-channel radio remote control– Proximity switch (radar)– Safety light barriers (infrared)
Options
The Klaus company reserves the right in the course of technical progress to use newer or other technologies, systems, processes, proceduresor standards in the fulfillment of their obligations other than those originally offered provided the customer derives no disadvantage fromtheir so doing.
To be performed by the customer
Lockable main switch per main cabinet. The lockable main switch isto be mounted directly next to the main cabinet.
Main switch
Recess for drive motor and turntable, drainage of the recess.
Recess
Embedding in concrete.
Embedding
Optionally required drainage.
Drainage
Conduit EN 25 (M25) with taut wire between the drive pit and themain cabinet.
Conduit
The supply line to the main cabinet must be provided by the customerduring installation. The functionality can be monitored on site by ourfitters together with the electrician. If this cannot be done duringinstallation for some reason for which the customer is responsible,the customer must commission an electrician at their own expenseand risk.
Electrical supply to the main cabinet
– Costs for final technical approval by an authorized body
If the following are not included in the quotation, they will alsohave to be provided / paid for by the customer:
Lighting, ventilation, fire extinguishing and fire alarm systems.
Building services