JPW7320 Installation Guideline v1.0

8/12/2019 JPW7320 Installation Guideline v1.0

1/25

JPW-7320 Specification and

Installation Guide


2/25

Contents

1. Notice

2. JPW-7320 Installation materials

3. JPW-7320 Design spec & concept

4. JPW-7320 Drawing5. Interface Pin & Connector Specs.

6. JPW-7320 Accessory List

7. Unpacking

2Juni | KoreaProprietary and Confidential

.

9. Installation

10. Customized Parts

11. JPW-7320 Ports Function

12. Alarm Interface External Battery Rack Configuration

13. Appendix : Power Configuration Concept


3/25

1. Notice

The material contained in this document is provided as is, and is

subject to being changed, without notice, in future editions. Further, to

the maximum extent permitted by applicable law, Juni disclaims all

warranties, either expressed or implied with regard to this manual and toany of the Juni products to which it pertains, including but not limited to

the implied warranties of merchantability and fitness for a particular

purpose. Juni shall not be liable for errors or for incidental or


, ,

performance of this document or any of the Juni products to which it

pertains. Should Juni have a written contract with the User and should

any of the contract terms conflict with these terms, the contract terms

shall control.


4/25

Rectifier, Battery

Pole mount bracket (1set)

Pole mount banding strap

RJ-45 connector

Backhaul equipment & Network(Backhaul ~ JPW-7320)

(AC connector or DC connector), Ground 5m cable with rug

AC Power Cable (JPW-7320 ~ Rectifier)

2. JPW-73200 Installation Materials


Ground cables from the MGB to JPW-7320

Ground cables from the MGB to Source

Grounding facilities & cables the MGB (distributor)

Lightning facilities

RF ANT (dual polarization, DIN-female type)

RF feeder Cable (1/2)

RF connector (1/2 n-male type)

RF connector (7/16 DIN-male type)

Tube (RF Ant)

Cable tray & Cable duct

J : Juni


5/25

Mechanical Char. Size : 120mm x 124mm x 500mm ( WxDxH )

Pole Mount / Wall Mount

Weight : Under 9Kg

Electrical char

Power Consumption : Under 80W ( 1.5W )120W Power Supply (PFC)

Battery Backup Support - Alarm function

Input Range : 84Vac ~ 264Vac or -48Vdc

RF Char

3. JPW-7320 Design Spec & Concept


1.5W Antenna Power output GPS with external Antenna

Environment Operating Temperature : -20 ~ 50

Storage Temperature : -40 ~ 85

Cold Start

Humidity : 5% ~ 95% non condensing Protection Level : IP65

Vibration : zone 3

Solar Cover (Option)


6/25

Passive Cooling

Airtight Enclosure

Pole Mount & Wall Mount Support

Variable Polemount Bracket Option ( For variable Pole Size)

Solar Cover Option

1 Person Installation



Side Front Solar Cover Side Rear Bottom

Top


7/25

Pole Mount Type Wall Mount Type




8/25

4. JPW-7320 Drawing



9/25

4. JPW-7320 Drawing



10/25

5. Interface Pin & Connector Spec.



11/25

6. JPW-7320 Accessory List



12/25

6. JFW-700 Accessory List



13/25

7. Unpacking



14/25

Avoid direct sunlight and place the unit in a well ventilated location.

Ground connections must be made to all metal cabinets for safety.

Avoid any vibration. The VSWR of the cable which connects the JPW-7320 to the antenna should be

less than 1:1.5

The distance between two antenna should be 50cm at minimum. (When usingvertical polarization antennas. Recommendation)

8. Installation Conditions



15/25

1. Mount the pole mount bracket to thepole and fasten the band

2. Insert hooks of pole mount bracket to

the JPW-7320 bracket holes

3. Fasten the JPW-7320 using included

nuts and washers.

4. When the product is fixed, use band to

fasten the lower part of JPW-7320.5. Bind Ethernet Line and AC220 V Line

using included water-proof connector

assembly

6. If necessary, additional water-proof

finishing can be applied to joints of

connectors.

9. Installation


7. Recommend pole: 75~170mm radius

8. The VSWR of the cable which

connects the JPW-7320 to the antenna

should be less than 1:1.5


16/25

9. Ground specificationBasically JPW-7320 is common ground system between power ground and communication ground, so when

power ground is well provided, the below communication ground installation can not be used.

A. Ground wire : Diameter should be bigger than 1.6mm or the cross-sectional area should be bigger than

2mm2 (bigger than 14AWG). In case of aluminum wire, the diameter should be bigger than 2.6mm and the

wire should be outdoor type wire.

B. Ground : Ground scheme should comply the IEEE/ANSI STD 81-1983. Even though the grounding resistor

is required to be less than 10 ohm, Juni recommends to use resistor less than 5 ohm. It should use ground

different from lightning protection ground.

C. Grounding type : JPW-7320 uses common grounding scheme and exterior ground does not have to be

rounded if the ower round works fine. However if the ca acit of ower roundin is considered to be

9. Installation


not big enough, Juni recommends to use the exterior ground using the ground socket located at the

bottom of JPW-7320.


17/25

Solar Cover Install

9. Installation



18/25

Passive Protection Cover Open State Cable Assembly installed

9. Installation


over

AC Power Harness DC Power Harness

* Protection for wrong insertion

* IP65 Protection Level

RJ 45 water-proof cable harness


19/25

Power Harness assembly

DC

12

3 43

1 2

AC

2 1

3

1 2

3 4

9. Installation


1 Pin: ACL

2 Pin: ACN

3 Pin: F.G

(Harting: TB 09 46 245 3410)

1 Pin: GND2 Pin: GND

3 Pin: -48V

4 Pin: -48V

(Harting: 09 46 245 4400)


20/25

PSU ARCH AQF120O-48S

10. Customized Parts (for example)



21/25

Ethernet Maintenance DryCT/Test

DC InAC In

ANT Arrestor

11. Ports function


LEDVent

GPS ANT with Water Proof Panel


22/25

12. Alarm Interace External Battery Rack Configuration

22Juni | KoreaProprietary and Confidential22

3

2

1

4

5

Battery Rack

3

2

1

4

5

JPW-7320

VCCPhotocoupler or Relay Structure


23/25

Appendix: Power Configuration Concept

Case 1. UPS Configuration

UPS is mostly commercial product and it

is hard to provide DryContact. Additional

alarm process is needed.

JPW-7320

RF Digital

DC

UPS

FANSeries Battery

Control


PD

AC

AC-DC27Vdc

Back

Haul

RJ45

POE

AC

Maint

enanc

e

RJ45

Dry

Contac

t

RJ45

AC

3P

DC

2P

100-240Vac

RectifierInverter

SWITCH


24/25

Case 2. DC Backup Configuration

JPW-7320 Battery Rack

12V

-ES BAT +

12V

-ES BAT +

Control

Module

Series Battery

Dry

Contact

RF Digital

DC

Heater

FAN

Battery Rack Spec

12V

-ES BAT +

12V



PD

Rectifier &

Power Dist.

AC

AC-DC-48Vdc

Back

Haul

RJ45

POE

AC

Maint

enanc

e

RJ45

Dry

Contac

t

RJ45

AC

3P

DC

2P

100-240Vac

DC

LOAD

-


25/25

Case 3. Solar Panel Configuration (Except AC)

JPW-7320 Battery Rack

RF Digital

SolarPanel

12V

-ES BAT +

12V

-ES BAT +

Series Battery

FAN

12V

-ES BAT +

12V

Solar Panel

(24V/180W)Vmp : 37.5V

Imp : 4.8A

Voc : 44VIoc : 5.25A

+

-

Solar Panel

(24V/180W)

+



PD

Back

Haul

RJ45

POE

DC

Maint

enanc

e

RJ45

Dry

Contac

t

RJ45

NADC

2P

Control

Module

-

DC

LOAD

DC-DC (75W)

48-28Vdc

mp : .

Imp : 4.8A

Voc : 44VIoc : 5.25A

-

48Vdc

Range

42~70

48VdcRange42~52

Documents

JPW7320 Installation Guideline v1.0