Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . .2 ... Manual Dual-Zone Climate Control (if equipped) Select airflow source • Turn the Mode knob on the right of

Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . .2Instrument Panel Cluster . . . . . . . . . . . . . . . . . . .3Malfunction Indicator Lamp . . . . . . . . . . . . . . . . .4Heated Front Seats . . . . . . . . . . . . . . . . . . . . . . . .4Interior Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Manual Dual-Zone Climate Control . . . . . . . . . . .5Automatic Dual-Zone Climate Control . . . . . . . .6Rear Seat Climate Controls . . . . . . . . . . . . . . . . .7Content Theft-Deterrent System . . . . . . . . . . . . .8Lockout Protection . . . . . . . . . . . . . . . . . . . . . . . .8Headlamp Controls . . . . . . . . . . . . . . . . . . . . . . . .8Heated, Power Outside Mirrors . . . . . . . . . . . . . .9Outside Mirror with Curb View Assist . . . . . . . . .9Memory Seats . . . . . . . . . . . . . . . . . . . . . . . . . . .10Electric Adjustable Pedals . . . . . . . . . . . . . . . . .10

Entertainment Systems . . . . . . . . . . . . . . . . . . .10Rainsense Wipers . . . . . . . . . . . . . . . . . . . . . . . .12Headlamp Washers . . . . . . . . . . . . . . . . . . . . . . .12Universal Home Remote . . . . . . . . . . . . . . . . . . .13OnStar® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Driver Information Center (DIC) . . . . . . . . . . . . .14Sun Visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16Electronically Controlled Air Suspension . . . . .16Air Inflator System . . . . . . . . . . . . . . . . . . . . . . .16Four-Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . . .17StabiliTrak® – Stability Control System . . . . . . .17Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . . . .18Roadside Assistance . . . . . . . . . . . . . . . . . . . . .20My GMLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Congratulations on your purchase of a GMC Envoy. Please read this information and your Owner Manual toensure an outstanding ownership experience. Note that your vehicle may not include all the featuresdescribed in this booklet. Keep this booklet with your Owner Manual for easy reference.

A. Exterior Lamp ControlsB. Air OutletsC. Turn Signal/Multifunction LeverD. OnStar®/Audio Steering Wheel

ControlsE. Instrument Panel ClusterF. Audio Steering Wheel Controls

G. Ignition SwitchH. Audio SystemI. Climate ControlsJ. Hood ReleaseK. Driver Information Center (DIC)

Steering Wheel ControlsL. Transfer Case Controls

M.Shift LeverN. LighterO. Accessory Power OutletsP. Parking BrakeQ. Rear Window Washer/WiperR. Rear Window DefoggerS. Glove Box

Getting to Know

YourEnvoy2

Instrument Panel

See Section 3 of your Owner Manual.

3


A

B C

DE

F

Instrument Panel Cluster

Your vehicle’s instrument panel isequipped with this cluster or one verysimilar to it. The instrument panelcluster includes these key features:A. TachometerB. Speedometer

C. Oil Pressure GaugeD. Fuel GaugeE. VoltmeterF. Engine Coolant Temperature

Gauge

NOTE: The instrument panel clusteris designed to let you know aboutmany important aspects of your vehi-cle’s operation. It is important to readyour Owner Manual and becomefamiliar with the information beingrelayed to you by the lights, gaugesand indicators, as well as what actioncan be taken to ensure safety and toprevent damage.

Getting to Know Your Envoy4

Heated Front Seats (if equipped)

Select a heat setting for both theseatback and seat cushion• Press and release the button labeled

with the heated seat ( ) icon located on the front door armrest until the indicator lights designateyour setting: three for High, two forMedium, one for Low and none for Off.

Select a heat setting for the seatbackonly• Press and release the vertical heated

seat button until the switch indicatesthe desired setting: three for High,two for Medium, one for Low andnone for Off.

The engine must be running to operatethis feature.See Section 1 of your Owner Manual.

Malfunction Indicator Lamp(Service Engine Soon Lamp)

This instrument panel cluster lamp illuminates under a variety of conditionswhen the On-Board Diagnostics II (OBDII) system detects a malfunction in thevehicle’s emission controls.If the Malfunction Indicator Lamp is lit steadily, check the gas cap toensure it is present and securely fastened • Turn the cap clockwise until a ratch-

eting sound is heard, signaling that itis secure.

• If this is the cause of the condition, afew driving trips with the cap installedproperly should turn the light off.


Interior Lamps

Your vehicle is equipped with illuminatedentry and exit lighting as well as domelamps.Activate illuminated entry feature• Open a door or press the Unlock

button on your Remote Keyless Entrytransmitter.

• With all doors closed, the domelamps stay illuminated briefly and turnoff automatically.

Disable entry and exit lighting • Push in the Dome Override button

located below the exterior lampsswitch (see “A” above). This will over-ride the illuminated entry featureunless the Remote Keyless Entrytransmitter is used to unlock the vehicle. The Dome Override featureis useful when the vehicle doors needto be open for a long period of time.


A

5

Manual Dual-Zone ClimateControl (if equipped)

Select airflow source• Turn the Mode knob on the right of

the heat and A/C control panel to thedesired setting:( ) Instrument panel vents( ) Instrument panel vents and

floor vents( ) Floor vents( ) Floor, windshield and side

window vents( ) Windshield and side window

ventsRaise or lower fan speed• Turn the fan control knob ( ).

Adjust the dual temperature controls• Use the lever on the left-hand side of

the climate control panel to adjust thetemperature on the left side of thevehicle.

• Use the right-hand lever to adjust thetemperature on the right side of thevehicle and the temperature for thesecond row.

Cool the vehicle interior more quicklyon very hot days• Choose the coolest temperature

setting.• Activate the Recirculate ( ) and

A/C ( ) buttons.• Place the A/C mode knob in the Vent

mode.• Open the windows just long enough

to let the hot air escape.Turn on the rear window defogger• Press the rear window defogger

( REAR) button.• An indicator light on the button will

come on to let you know the rear window defogger is active.



Automatic Dual-Zone ClimateControl (if equipped)

Manually select desired airflowsource• Press and release the MODE button

until the desired source is indicatedon the display. Mode selectionsinclude Vent, Bi-Level, Floor andDefog/Defrost.

Manually raise or lower fan speed• Press the upper or lower portion of

the fan control ( ) button.

Manually adjust the dual temperaturecontrols• Use the knob on the left-hand side of

the climate control panel to adjust thetemperature on the driver side of thevehicle. Use the right-hand knob toadjust the temperature on the pas-senger side of the vehicle as well asthe second row.

• To match and link the passenger-sidetemperature to the driver’s, press andhold the AUTO button for three seconds.

Recirculate interior air and preventoutside air from entering your vehicle• Press the Recirculate ( ) button.This feature can be activated while inthe Vent or Bi-Level mode, but not inDefog, Defrost or Floor mode.Clear the windshield and front sidewindows of fog or frost more quickly• Press the FRONT button.Clear the rear glass of fog or frostmore quickly, and activate the heatedoutside rearview mirrors (if equipped)• Press the REAR button.See Section 3 of your Owner Manual.

7

Rear Seat Climate Controls(if equipped)

(5-Passenger Vehicle System shown)

Turn the rear controls on and off (5-passenger vehicle)• Press the PWR ( ) button. The

rear controls do not function when the front climate control is inDefrost mode.

Turn the rear controls on(7-passenger vehicle)• Set the rear HVAC knob (located on

the front floor console) to R.

Change the direction of airflow• Use the mode knob on SLE (or the

button on SLT models) to selectUpper, Bi-Level or Floor.

Set the temperature of air through therear outlets (5-passenger vehicle)• Temperature of air from the rear

outlets is determined by the front passenger temperature setting.

Set the temperature of air through the rear outlets from the rear control(7-passenger vehicle)• Set the rear HVAC knob (located on

the front floor console) to R.• Turn the center knob on the control

panel to choose a temperature (onSLE models) or use the temperaturebutton with the arrows on SLT.

Adjust rear fan speed (7-passengervehicle)• Use the fan button with the arrows

(on SLT) or the fan control knob onSLE models.



Content Theft-Deterrent System

Arm the Content-Theft DeterrentSystem• Lock the doors using the power door

lock switch or by pressing the Lockbutton on the Remote Keyless Entrytransmitter.

• After closing all doors, the securitylamp on the radio stops flashing andremains lit. After a delay of about 30seconds, the lamp darkens and thesystem arms itself.

• When arming with the power doorlock switch, at least one door must beopen and the key must be removedfrom the ignition. (A door does nothave to be open to arm the systemwith the Remote Keyless Entry transmitter.)

• The system will not arm if the door islocked with a key or the manual doorlock button is pressed.

• If the alarm is tripped, the hornsounds and the headlamps/taillampsflash for about two minutes. Thealarm sounds whenever a lockeddoor is opened without the key orRemote Keyless Entry transmitter, orif someone attempts to turn on theignition without the correct key.

Turn off the alarm • Unlock a door with the key or press

Unlock on the Remote Keyless Entrytransmitter.

• Starting the engine with the correctkey will also turn off the alarm.


Lockout Protection

Prevent your ignition key from beinglocked in your vehicle• When the key is in the ignition and

a door is open, pressing any powerdoor lock switch unlocks the driverdoor and locks all other doors.


Headlamp Controls

The exterior lamps knob is located onthe instrument panel, to the left of thesteering wheel.Turn off the Daytime Running Lamps(DRL) and automatic headlamp system• Move the knob to the OFF ( )

position.The automatic headlamp system auto-matically reactivates at the next key-on.

9

Activate the Daytime Running Lamps(DRL) and automatic headlamp system• Move the knob to the AUTO ( )

position.• All exterior lamps and the instrument

panel/radio lights will illuminate whenthey are needed.

Manually activate the parking lamps,side-marker lamps, taillamps, instru-ment panel/radio lights and licenseplate lamps• Move the knob to the parking lamp

( ) position.Manually activate the headlamps, allexterior tail/marker lamps and theinstrument panel/radio lights• Move the knob to the ON ( )

position.Activate the fog lamps• Press the button (see “A” below)

located on the instrument panel to theright of the exterior lamps switchonce.

• An indicator lamp will illuminate.• To turn them off, press the button

again. See Section 3 of your Owner Manual.

Heated, Power Outside Mirrors(if equipped)

Activate heat feature on the poweroutside mirrors • Press the rear window defogger

button on the climate control panel. See Section 2 of your Owner Manual.

Outside Mirror with Curb ViewAssist (if equipped)

This feature automatically adjusts thepassenger side mirror downward to apreset tilt position when the vehicle is inReverse gear. The mirror returns to itsnormal position when the vehicle ismoved out of Reverse. See your OwnerManual to activate this system for thefirst time.See Sections 2 and 3 of your Owner Manual.

A


Memory Seats (if equipped)

Save driver seat preference memorysetting• Adjust the driver seat (including seat-

back recliner and lumbar) to a com-fortable position.

• Press and hold either the driver 1 ordriver 2 memory button located onthe driver’s door. A double chime willsound to confirm your settings.

To program settings for a second driver,repeat the same procedure using theother numbered memory button.See Section 2 of your Owner Manual.

Electric Adjustable Pedals

Adjust the brake and accelerator pedals to comfortable positions• Press the switch located on the steer-

ing column toward you to move thepedals closer to you.

• Press the switch away from you tomove the pedals away from you.


Entertainment Systems

Set the time on radios without usingthe Radio Data System (RDS)• Press the H or HR button until the

correct hour appears on the display.• Press and hold the M or MIN button

until the correct minute appears onthe display.

The time may be set with the ignition onor off.

Note: The pedals cannot be positionedfarther away from the driver than theyare in their standard position. This feature can be programmed to workwith the memory function (if equipped)on your vehicle. Adjustment of the powered pedals requires that the vehicle be in Park.

11

Set the time to an FM station’s RadioData System (RDS) setting (if equipped)• Press and hold both HR and MN for

two seconds until UPDATED and theclock symbol appear on the display.

• If the time is not available from thestation, NO UPDAT appears in thedisplay.

Program radio station presets• Turn the radio on.• Press the BAND button to select the

band (AM/FM1/FM2/XM1/XM2).• Use the seek or tune knob to tune in

the desired station.• Press AUTO EQ to select the equal-

ization that best suits the type of station selected.

• Press and hold one of the six num-bered buttons until a beep sounds;release the button.

• Repeat these steps for each stationpreset, using a different numberedbutton for each station.

Display a station’s INFO messagewhen INFO appears on the display• Press INFO to see the message.

Once the complete message hasbeen displayed, INFO disappearsfrom the display.

Tune to an RDS broadcast of a selected program type• Press the TYPE button to select the

Program Type you want to listen to. • Press the or button.

Access one of the two available XMSatellite Radio bands (if equipped) • Press the BAND button until XM1 or

XM2 appears on the display.

Load one CD into the Six-Disc CDPlayer (if equipped)• With the ignition on, press and

release the LOAD side of the LOADCD button.

• Wait for the indicator light at the rightside of the slot to turn green.

• Insert the disc partway into the slot,label side up; the player will pull thedisc in.

Load multiple CDs• With the ignition on, press and hold

the LOAD button for two seconds.The unit beeps and the light to theright of the slot begins to flash.

• When the light stops flashing andturns green, insert a disc partway,label side up.

• The indicator light will begin blinkingand then turn green. Load anotherdisc at this time.

• When loading more than one butfewer than six CDs, press the LOADbutton again to signal that loading iscomplete.


• When more than one disc is loaded, a number for each disc is displayed.

• To play a specific CD, press the CDAUX button and then the number ofthe CD you want to hear.

• A small bar appears under the CDnumber that is playing, and the tracknumber appears.

MP3 Radio (if equipped)A CD-R or CD-RW containing MP3audio tracks will play automatically wheninserted into the CD/MP3 player.See Section 3 of your Owner Manual.

Rainsense Wipers (if equipped)

Rainsense Wipers automatically controlthe frequency of the wipers from Off toHigh speed according to the amount ofmoisture on the windshield.

Headlamp Washers (if equipped)

Spray the headlamps with washerfluid• Press the headlamp washer button

(see “A” above) located on the instrument panel to the left of thesteering wheel.


Activate the Rainsense feature• Set the wipers to one of five moisture

sensitivity settings on the multifunc-tion lever.

• The closer the setting is to the Offposition, the less sensitive it will be tomoisture.


Note: Turn this feature off before enter-ing an automatic car wash.Note: CDs with any affixed labels may

jam in the CD player. Label a CD usinga permanent marker. If more than oneCD is inserted into the slot at one time,or if scratched or damaged CDs areplayed, the CD player could be dam-aged. When using the CD player, useonly CDs in good condition withoutlabels; load one CD at a time; and keepthe CD player and the loading slot freeof foreign materials, liquids and debris.

A

13

• Press and hold the remote buttonagain. If the indicator light stays litconstantly, programming is complete.

• Continue programming additionaldevices using the transmitters, but donot press the two outside buttons onthe remote again.

If the remote indicator light blinks rapidlyfor two seconds and remains on, it indicates that your device (usually agarage door opener) has a “rollingcode.” Continue with the following steps:• Press the training button (sometimes

marked “LEARN” or “SMART”) on thegarage door opener motor head unit,making sure that the indicator lightflashes to confirm training mode.

• Within 30 seconds, press and holdthe remote button programmed in theprevious steps for two seconds.

• Press and release this button threetimes, holding it for two-second intervals to ensure that the remotehas been trained.


Universal Home Remote (if equipped)

The controls for this feature are locatedon your overhead console.Program the Universal Home Remote • Turn the ignition OFF.• Press and hold down the two outside

remote buttons until the indicator lightflashes; then release the buttons(about 20 seconds — do not hold formore than 30 seconds). Do notrepeat this step for the second orthird devices that you plan to add tothe Universal Home Remote system.

• Hold the end of your hand-held trans-mitter up to three inches away fromthe surface of the remote and pressand hold the transmitter button andthe button you wish to assign it to onthe remote.

• Continue holding both buttons (up to 90 seconds may pass as theremote is being programmed); theindicator light will begin blinking slowly, then more quickly. Program-ming is complete when the light onthe remote flashes rapidly.

• Release both buttons.


OnStar® (if equipped)

The OnStar system provides in-vehiclesafety, security, and phone services,available 24 hours a day, 7 days aweek. These services are easilyaccessed through the three OnStar buttons in your vehicle. • Press the white Phone button to

access OnStar Personal Calling, ahands-free, voice-activated phoneservice.*

• Press the blue OnStar button to con-nect to an OnStar Advisor for servic-es such as GM Goodwrench RemoteDiagnostics or routing and locationassistance.**

• Press the red Emergency button toconnect to an OnStar Advisor whocan contact a nearby emergencyservices provider to dispatch ambu-lance, police, fire, or other emergencyservices to your location.

For more information about OnStar fea-tures, refer to the OnStar Owner’sManual and Audio CD, located in yourglove box.*Available in most markets

**Routing and location assistance may requireservice upgrade


Driver Information Center (DIC)(if equipped)

Your vehicle’s Driver Information Center(DIC) is located in the instrument panelcluster.Access DIC modes• Press one of the following DIC but-

tons located on the steering wheel.– Trip Information ( )– Fuel Information ( ) – Personalization ( )– Select settings ( )

Trip Information Button• Press to scroll through the

odometer, TRIP A, TRIP B, andTIMER. When either TRIP A or TRIPB is displayed, you can press theSelect button ( ) to reset the displayed odometer.

• You can also reset a trip odometer to zero by pressing and holding thereset stem for four seconds. WhenTIMER is displayed, you can press

to start or stop the timer. To resetit to zero, push and hold whileTIMER is displayed.

Fuel Information Button • Press to scroll through the range,

average fuel economy, fuel used andthe GM Oil Life SystemTM.

• RANGE estimates the remaining dis-tance you can drive without refueling.Range is based on recent fuel econo-my and the fuel remaining in the tank.

• AVG. ECON calculates how manymiles per gallon you are gettingbased on overall driving conditions.Press and hold the Select button ( ) while AVG. ECON is displayedand the DIC will begin calculating theaverage fuel economy from that pointin time.

• FUEL USED shows the currentamount of fuel used in gallons sincethe last reset for FUEL USED. Thismode should be reset after every fueltank fill-up.

• ENGINE OIL LIFE calculates an esti-mate (percentage) of the engine oil’sremaining useful life. It also will alertyou when it is time to change your oilby illuminating the CHANGE ENGOIL light on the DIC. Please remem-ber to always reset the oil life systemafter an oil change by pressing andholding for four seconds whileENGINE OIL LIFE is displayed. Whensuccessful, the DIC will displayENGINE OIL LIFE: 100%.

15

Note: If your vehicle is not equippedwith DIC steering wheel buttons, pressthe trip odometer reset stem located inthe instrument panel cluster to selectthe information. Hold the stem for fourseconds to reset trip odometers.

Personalization Button• Press once and the vehicle settings

will be displayed. Press again toscroll through and set the personal-ization features.

Select Button• Press to scroll through the menu

choices for each personalization feature. Finalize your choice bypressing while it is displayed onthe DIC and move on to the next feature.

• The personalization features can bereset to their default mode by holding

and down for four seconds. Language Options• If you find that the unit displays a lan-

guage other than the one you preferand you are unable to change it, hold

and down until the display begins cycling through the threeavailable languages. Release the buttons when you see the preferredlanguage.

Displaying Driver Preferences• The driver preferences are recalled

by pressing memory button 1 or 2located on the driver’s door. The lastvalue displayed for each preferenceis saved automatically.



Sun Visors

Block glare • To help block the sun’s glare, rotate

the sun visor down.• Block the driver or passenger front-

side window glare by turning the sunvisor to the side window.

• Pull out the sun visor extender (ifequipped) for additional window coverage.


Electronically Controlled Air Suspension (if equipped)

Occasional whirring and/or hissing sound under the rear of thevehicle• This sound indicates that the sys-

tem’s air compressor is operating toprovide a level ride height, and is normal.


Air Inflator System (if equipped)

Locate the airinflator unit and kit• The inflator unit

is in the rearcompartment onthe passengerside of the vehi-cle, behind anaccess cover.

• An inflator kit,with a 22-foot hose and three nozzleadapters, is located in the glove box.

Use the air inflator• Open the access cover.• Attach the appropriate nozzle adapter

to the end of the hose (if required).• Attach that end of the hose to the

object you are inflating. Attach theother end of the hose to the inflatoroutlet.

• Press and release the on/off switch toturn the air inflator on. An indicatorlight verifies that the inflator is running.

• When inflation is complete, press andrelease the on/off switch again.

• Remove the hose from the outlet(load leveling will not operate whenthe hose is attached to the outlet).


17

Four-Wheel Drive (if equipped)

Envoy’s four-wheel drive system rotarycontrols are located on the instrumentpanel. Your vehicle will have one of theabove transfer case knobs.Shift into 4HI, 4 , A4WD or AUTO • Turn the knob to 4HI, 4 , A4WD or

AUTO. This can be done at anyspeed except when shifting from 4LOor 4 .

Shift into 2HI or 2• Turn the knob to 2HI or 2 . This can

be done at any speed except whenshifting from 4LO or 4 .

Shift into or out of 4LO or 4• With the ignition in RUN and the vehi-

cle stopped or moving less than 3mph (4.8 km/h), shift the transmissioninto Neutral.

• Turn the knob to 4LO (4 ), 2HI (2 ),4HI (4 ) or A4WD (AUTO), preferablywith the vehicle moving 1 to 2 mph(1.6 to 3.2 km/h).

• Wait for the indicator lamp to stopflashing and remain illuminated; thenshift your transmission into gear.

Shift into NEUTRAL (N)• Place the transfer case in Neutral

only when towing your vehicle. See Section 4 of your Owner Manual for towing information.

See Sections 2, 4 and 5 of your Owner Manual.

StabiliTrak® – Stability ControlSystem

StabiliTrak combines antilock brake,traction control, and stability control sys-tems that help the driver maintain direc-tional control of the vehicle in most driv-ing conditions. The system is designedto help keep the vehicle on the driver’sintended path by using throttle andbrake intervention.When activated, the system will applybraking to individual wheels and mayreduce engine power as necessary tohelp you maintain directional control ofthe vehicle. You may also hear a noiseor vibration, or feel a reduction in accel-eration, while the system is active. Thisis normal.StabiliTrak is automatically turned onwhen the vehicle is started and does notrequire any driver input. It is recom-mended to leave the system on at alltimes for normal driving. It may be nec-essary to turn off the system if the vehi-cle is stuck in sand, mud or snow.To turn off StabiliTrak, press and holdthe (StabiliTrak) button on the trans-mission shift handle for five seconds.STABILITRAK OFF will be displayed onthe DIC. Press the button again to turnthe system back on. See Section 4 of your Owner Manual.


Luggage Carrier (if equipped)

Slide the crossrails to desired position• Pull up the lever on each side of the

crossrail. This will release the cross-rail and allow you to slide it.

• When the crossrail is where you wantit, press down on the levers to lock itin place.

Reduce wind noise when the roof luggage carrier is not in use• Position the rear crossrail at the

rearmost position and the front crossrail above the rearmost portionof the rear door opening (above the C-pillar).


Note: Never carry anything on the vehi-cle roof that is longer or wider than theluggage carrier itself. (Examples: ply-wood, paneling, a mattress.) The loadcould be violently torn off, causing youor others to have a collision.

Loading cargo that weighs more than220 pounds (100 kg) on the luggagecarrier may damage your vehicle.

19

Notes


Roadside Assistance

My GMLink

1-800-GMC-8782 (1-800-462-8782)TTY: 1-888-889-2438As the proud owner of a new GMC vehicle, you are automatically enrolled inthe GMC Roadside Assistance program. The toll-free number is staffed by a teamof technically trained advisors, who areavailable 24 hours a day, 365 days ayear. Roadside Assistance provides strandedowners with over-the-phone roadsiderepairs, location of the nearest GMCdealer or the following special services:• Flat Tire Assistance• Fuel Delivery• Lockout Service• Emergency Towing Service• Jump StartFor prompt and efficient assistancewhen calling, please provide the follow-ing information to the advisor:• Location of the vehicle• Telephone number and your location• Vehicle model, year and color• Vehicle mileage

The GMC Owner Center at My GMLinkis a complimentary service for GMCowners, a one-stop resource to enhanceyour GMC ownership experience.Exclusive member benefits includeonline service reminders, vehicle main-tenance tips, online owner manual, spe-cial privileges and more. Sign up todayat www.mygmlink.com.

• Vehicle Identification Number (VIN)• Vehicle license plate numberGMC reserves the right to limit servicesor reimbursement to an owner or driverwhen, in GMC’s judgment, the claimsbecome excessive in frequency or typeof occurrence.Roadside Assistance and OnStar (if equipped)If your vehicle is OnStar-equipped,press the blue OnStar button and thevehicle will send your current GPS loca-tion to an OnStar Advisor who will speakto you, assess your condition, contactRoadside Assistance and relay yourexact location so you will get the helpyou need.

Certain restrictions, precautions and safety procedures apply to your vehicle. Please read your OwnerManual for complete instructions. All information contained herein is based on information available atthe time of printing and is subject to change without notice. Copyright 2005 by GM Corp.All rights reserved.

06ENVOYGTK A!06ENVOYGTK=A!

Documents

Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . .2 ... Manual Dual-Zone Climate Control (if equipped) Select airflow source • Turn the Mode knob on the right of