Instruction ManualTIVOLI PAS TD for TIVOLI

GU Electronic

INDEX

Specifications

1. Main Spec. ----------------------------------

2. Diagram -------------------------------------

3. Components --------------------------------

4. Exterior --------------------------------------

Settings

1. Dip Switch ----------------------------------

2. Original button -----------------------------

3. Touch ---------------------------------------

4. Key board -----------------------------------

5. OSD Menu ----------------------------------

Installation

1. Installation Diagram ------------------------

2. Installation ----------------------------------

3. Caution --------------------------------------

2

3456

7891010

161719

GU Electronic

Specification

1. Main spec.

1-1 Input Spec. (MULTI VIDEO INTERFACE)- 1 x Analog RGB Input (Navigation System source)- 1 x Digital RGB Input (Navigation System source)- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)- 1 x LVDS Input. (Car Command System)

1-2 Output Spec.- 1 x LCD Output (LCD Operation)

1-3 Power Spec.- Input Power : 8VDC ~ 24VDC- Consumption Power : 12Watt, Max

1-4 Switch Input mode- Possible to switch input mode through original button

2. Features

- Display dynamic PAS(Parking assistance system)- Easy installation with plug & play Power cable

3

GU Electronic

Specification

3. Diagram

4

INTERFACE

Scaler(PIP)

MCU

CAR COMMAND

SYSTEMCAN

EEPROMCAN

RECEIVER

CAR TFT-LCD

REAR CAMERA

RGB+Sync

DIGITAL RGB LVDS

FRONT CAMERA

COMPOSITE

COMPOSITE

LVDSTX

RELAY

LVDSRX

LVDSTX

LVDS

REAR CAMERAPOWER

GU Electronic

Specification

4. Components

5

OSD cable 1EA(Code: CB-OSD10-CMX)

Power cable 1EA(Code: CB-SSTV12-PWR-CMX)

RGB NAVI cable 1EA(Code: CB-RGB7-CMX)

Touch cable(KD900) 1EA(Code: CB-LRVx51-TOUCH-CMX)

Screw 4EA(Code: GN_BT_0010)

FFC cable 1EA(Code: CB-FFC-CMX-29)

OBD cable 1EA(Code: CB-SSTV12-OBD-CMX)

Specification

5. Exterior

166.5mm

22mm

86mm

6GU Electronic

*Touch Connect

① Y-② X-③ Y+④ X+

① ② ③ ④

*NAVI Connect

① R DATA (Red)② G DATA (Green)③ B DATA (Blue)④ SYNC (White)⑤ GND (Black)⑥ DVB-T IR (Green)⑦ DVD IR (Orange)

① ② ③ ④ ⑤ ⑥ ⑦

*POWER Connect

1. Battery (Yellow) 2. N.C3. Rear-DET (Brown)4. Front-DET (Blue)5. CAN1-L (Green)6. CAN1-H (Orange) 7. CAN2_L (White) 8. CAN2_H (Purple)

1 15

2 16

9. FRONT-PWR (Pink)10. REAR-PWR (Red) 11. REAR-CAM (White)12. GND (Black) 13. FRONT-CAM (Yellow)14. GND (Black)15. GND (Black)16. GND (Black)

NAVIPOWER/CAN TOUCHDigital

DIP S/WIMAGE LVDS IN/OUT

PROGRAM

Settings

1. Dip Switch* ON : DOWN , OFF : UP

7GU Electronic

NO. Function Selection

1 NAVION : Skipping NAVI

OFF : Display

2 AV1 (DVB-T)ON : Skipping DVB-T

OFF : Display

3 AV2 (DVD)ON : Skipping DVD

OFF : Display

4 N.C

5 Touch typeON : Capacitive touchOFF : Resistive touch

6 N.C

7 N.C

8 CAR type OFF: TIVOLI

* Example

TIVOLI Model

Settings

8GU Electronic

Long press : Switching ModeShort Press : switching to OEM screen directly

NAVIOEM AV1 AV2

※ The screen is switched in order as the pictures below

2. Original button – Steering Wheel (Switching Mode)

Setup button – Capacitive touch model Menu button : Resistive touch model

9

Touch OEM screen in any mode more than 11sec. For calibration(This function can be activated only one time after switching mode)

Touch the “+” correctly

- DVB-T/DVD Control

Press Touch (Anywhere) Press Icon

DVB-T

DVD

Settings

GU Electronic

3. Touch screen – Touch calibration

Settings

10

5. OSD Menu※ Press “MENU” button on Key board

GU Electronic

Config - NAVI-RGB : Setup for the type of NAVI-RGB Config - DVB-T(DMB) : Setup for the type of DVB-T(DMB) Config - DVD : Setup for the type of DVDReset : Reset all value

4. OSD Key board

① MENU :Activating OSD Menu② SEL :Selection③ Up :Moving upward (Increasing value)④ Down :Moving downward (Decreasing value)

MENU SEL UP DOWN

① ② ③ ④

11

Settings

GU Electronic

Option• RearCam-Type : Setup for rear camera

ExtDevice - External rear cameraOEM - Original camera

• RearCam-Power : Setup for Rear VCC wire in power cableON - +12V out always (current consumption : 200mA)AUTO - +12V out in rear mode only (200mA)OFF - Power OFF

• RearCam-Det : Setup for Rear detection GEAR - By CANExtwire – by rear cam detect wire

• FrontCam-Type : Setup for front cameraExtDevice - External rear cameraOEM - Original camera

• FrontCam-Power : Setup for Front VCC wire in power cableON - +12V out always (current consumption : 200mA)AUTO - +12V out in rear mode only (200mA)OFF - Power OFF

5. OSD Menu※ Press “MENU” button on Key board

12

Settings

GU Electronic

5. OSD Menu※ Press “MENU” button on Key board

Option

• FrontCam-Det : Setup for front detection ExtDevice - External rear cameraOEM - Original camera

• FrontCam-RcvOpt : Selecting time of displaying Front camera before switching to RGB, DVD, OEM from Rear

• NAVI COM : Connect touch through UART ※ Necessary to get Uart protocol from Navi manufacturer

• Reset : Reset all value

Settings

13

- NAVI(RGB) Image / Screen

- DVD, DVBT, NAVI-AV, REAR, FRONT Image

GU Electronic

5. OSD Menu※ Press “MENU” button on Key board

Settings

14

- PDC ON/OFF

GU Electronic

Left Right DownUP

- Adjust the position of Parking guide line

Selecting a type of language (OSD Menu – Parking – Warning Lang)

Possible to adjust the position of line by Keypad in Horizontal / Vertical menu

※ Pressing this Horizontal / Vertical menu, The OSD screen automatically disappears. Please adjust from the parking line Screen.

Selecting a use of OPS(PDC) picture(OSD Menu – Parking – OSD Display – ON or OFF)

OPS Display - On

5. OSD Menu – Parking mode※ Press “MENU” button on Key board

- Language

15

- OSD

MENU Horizontal

OSDUtility

Horizontal VerticalDisplayTransparencyLanguage English

505010s30

- Utility

MENU Utility

OSDlUtility

Factory Reset CalibrationVersion

Execute CancelExecute Cancel

SSTV13KRX - 180106

• Utilityy– INTERFACE SOFTWARE

• OSD – Horizontal• OSD – Vertical• OSD – Display : Setting time for displaying OSD menu• OSD – Transparency• OSD – Language : Setting language of ODS menu

GU Electronic

Settings

5. OSD Menu※ Press “MENU” button on Key board

1. Installation Diagram

16GU Electronic

Installation

Head unit

Monitor

Offered Power cable

Offered Touch cable(KD900)

2. Installation

17GU Electronic

Installation

1. Disconnect OEM FFC cable from OEM PCB board

2. Connect the offered FFC cable to where the OEM FFC cable was disconnected

3. As picture above, Connect the opposite side of the offered FFC and the OEM FFC cable to interface board

OfferedFFC Cable

2. Installation

18GU Electronic

Installation

4. All cables should be passed through the hole

5. As picture above, fix the interface board by screw

19

Caution

• Not possible to switch mode- Check connection of OSD Key pad wire - Check CAN connection

• Display wrong size of picture- Check Dip s/w setting

• Display black screen in OEM mode- Check connection of LVDS/LCD cable

• Not possible to switch to rear screen- Check the packing setting(OSD Menu – option – RearCam-Det)

1. FAQ

• The device must not be installed in where it interferes driving(close to brake pedal, steering wheel, airbag etc.)

• LVDS cable must be connected correctly according to the manual

• Insulate the end of wire by using electrical tape

• The installation should be done by expert

• GU electronic does not take any responsibility for any problem caused by wrong installation

2. Caution

GU Electronic

For your better driving