Upload
others
View
17
Download
0
Embed Size (px)
Citation preview
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 1 von 13
Installation Manual Car-10 (Teltonika FM22,FM42, FM41, FM11)
Important InformationGeneral Information
DatasheetNavigate LED operation (GPS Signal)Status LED operation (GSM)
Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and IgnitionPositioning of the device with GPS antenna insde the devicePositioning of the device (optional)Installation Tests:
FM41 (GFSx44) Tracking DeviceFM41 Plug & PinsLED's
FM22 (GFSx22) Connection PlanLED's
FM42 (GFSx44) Connection PlanLED's
AccessoriesDriver Identification via I-Button Installation for FM4100 onlyDriver Identification via I-Button and Buzzer - FM41Driver Identification via I-Button and Buzzer - FM4200Temperature Sensors for GFSx44 (FM4100)Temperatur-Sensors FM4200
Installation Tests:Troubleshooting
Important InformationTroubleshooting RMA
General Instructions
Troubleshooting RMA
General Information
Datasheet
FM4200 User Manual v1.6.pdf
FM4100_User_Manual_v3.0.pdf
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 2 von 13
FM4100_User_Manual_v3.0.pdf
FM1100_User_Manaul_v015.pdf
image2015-5-15 11:27:48.png
Navigate LED operation (GPS Signal)
If ignition is ON and connected, the Navigate LED must blink every second.
Behavior Meaning
Permanently switched on GPS signal is not received
Blinking every second Normal mode, GPS is working
Off GPS is turned off because of deep sleep mode
Or GPS antenna short circuited
Status LED operation (GSM)
If ignition is ON and connected, the LED must blink every second and faster if data is transferred.
Behavior Meaning
Blinking every second Normal mode
Blinking every 2 seconds Deep sleep mode
Blinking fast for a short time Modem activity
Blinking fast constantly Boot mode
Off Device is not working or device firmware being flashed
Car-10 (Teltonika FM1100) Standard installation with Main Power, Ground and Ignition
Refer to the sticker on the device to find the correct wire for ignition, main power and ground!
PIN Typ Color Required Description
1 VCC DC YES Permanent power (10-30 Volt)
2 OUT2 Output 2
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 3 von 13
3 OUT1 Output 1
4 DIN 2 optional Input 2: e.g. privat switch
5 DIN 1 YES Input 1: connect with ignition signal
6 GND YES connect with ground
7 AIN 1 Analogue input (voltage values)
8 Data Dallas iButton driver data
9 DIN 3 Input 3
10 UCC Dallas iButton
Positioning of the device with GPS antenna insde the device
The device shall be placed UNDER the plastic dashbord with the sticker showing to the sky.
Positioning of the device (optional)
If acceleration plays a role, the device should be positioned horizontally and the main wire should show to the back or in driving direction
Installation Tests:
see Installation Tests and Reporting
FM41 (GFSx44) Tracking Device
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 4 von 13
FM41 Plug & Pins
PIN Type Colour Description
1 VCC (10-30) V DC Black Power + 10 V - 30 V DC Direct Current
11 GND (12-30) V DC Black Ground
16 DIN 1 Black Digital input / Ignition
LED's
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 5 von 13
FM22 (GFSx22) Connection Plan
The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 6 von 13
PIN Type Colour Description
1 GND (12-30) V DC Black Ground
2 VCC (10-30) V DC Red Permanent power + 10 V - 30 V Direct Current
3 DIN 1 Yellow Digital input 1 / Ignition
LED's
FM42 (GFSx44) Connection Plan
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 7 von 13
The GSM antenna is integrated in the device. You have to open the device for inserting the SIM card.
The following diagram shows how to connect to .main power, ground and ignition
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 8 von 13
PIN Type Colour Description
1 GND (12-30) V DC Black Ground
11 VCC (10-30) V DC Red Power + 10 V - 30 V Direct Current
15 DIN 1 Yellow Digital input 1 / Ignition
LED's
AccessoriesAccessories only work with the right tracking unit GFSx44 and are not included in the standard delivery.
You only have to read this chapter if you need to fix the accessories.
Take care that the FM4100 and FM4200 require DIFFERENT wiring connections.
It might be necessary to configure additional settings in the software in order to use the accessories.
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 9 von 13
Driver Identification via I-Button Installation for FM4100 only
The accessories must be provided by the same vendor as the tracking unit or it must be guaranteed that exactly the same type ibuttons and readers is used to make it work:
The I-Button Installation is only necessary for vehicles that shall be equipped with a driver identification. I-Button Installation only works with FM41 Box!
Connect and test the following:
PIN Type Colour Description
11 GND Grey iButton cable
8 Data White iButton cable
To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box
TESTS
LED lights ok
LED lights NOT OK
SMS-TEXT to GSM number
Feedback SMS (compulsory, if no feedback -> error)
SMS Test OK SMS Test NOT OK
GPS - - USR PWD readio 78 IO ID:78 Value:318767235 Value > 0
When you receive a Value, the iButton Reader works
No feedback or “IO ID:78 Value:0”
To test the installation, make sure that the ibutton is on the reader.
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 10 von 13
Driver Identification via I-Button and Buzzer - FM41
Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information.
In case if engine is started without connected Ibutton, in 5 seconds the external Buzzer connected to FM4100 is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. . The digital input 3 must be connected to ignition.
Connection Plan:
PIN Type Colour Description
11 GND Grey iButton cable
8 Data White iButton cable
18 DIN3 Ignition must be connected to DIN3 (not DIN1)
1 VCC Power Green Must be connected to Buzzer and reader
4 OUT3 Yellow Must be connect to Buzzer and
To complete the installation, the iButton system must be tested via SMS. In order to test your installation, you must attach an iButton chip to the reader and send an SMS-Test to the box
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 11 von 13
TESTS
LED lights ok
LED lights NOT OK
SMS-TEXT to GSM number
Feedback SMS (compulsory, if no feedback -> error)
SMS Test OK SMS Test NOT OK
GPS - - USR PWD readio 78 IO ID:78 Value:318767235 Value > 0
When you receive a Value, the iButton Reader works
No feedback or “IO ID:78 Value:0”
Driver Identification via I-Button and Buzzer - FM4200
Attention! This feature requires also a firmware update of each tracking unit. Contact your dealer for more information. In case if engine is started without connected Ibutton, the external Buzzer connected to device is starting alarming. Alarming stops after Ibutton is connected or/and Vehicle ignition is off. The digital input 1 must be connected to ignition.
Connection Plan:
PIN Type Colour Description
1 GND Black Grey iButton cable
13 1-Wire Data White iButton cable
15 DIN1 Yellow Ignition must be connected to DIN1
11 VCC Power Red Green iButton Cable
19 OUT1 Yellow iButton cable (based on ground) Must be connect to Buzzer and
11 VCC Power Red Red cable of alarm buzzer
19 OUT1 Black Black cable of alarm buzzer must be connected to ground
Temperature Sensors for GFSx44 (FM4100)
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 12 von 13
The temperature sensor is converting temperature into „iButton signal“.
Sensor type must be DS1820-PUR-7M. Connect and test the following
PIN Type Colour Description
20 PWD Data Green cable of sensor
8 Data Brown cable of sensor
11 GND White cable of sensor
Test per SMS
Temperatur-Sensors FM4200
Sensor type must be DS1820-PUR-7M. Connect and test the following:
GPS Fleet Software (www.gpsfleetsoftware.com)
Copyright © Software-Management Gmbh - Seite 13 von 13
PIN Type Colour Description
3 1 W PWD Data Green cable of sensor
13 1 W Data Brown cable of sensor
1 GND White cable of sensor
Tests per SMS:
TESTS
LED lights ok
LED lights NOT OK
SMS-TEXT to GSM number
Feedback SMS (compulsory, if no feedback -> error)
SMS Test OK SMS Test NOT OK
GPS - - USR PWD readio 72 IO ID:78 Value:318767235 Value > 0
When you receive a Value, the iButton Reader works
No feedback or “IO ID:78 Value:0”
Installation Tests:see Installation Tests and Reporting
Troubleshootingsee Troubleshooting RMA