Insal manual singo MR VB17.pdf

IDEA Manual

Installation Guide

0.0

syngo MR VB170.0 0.0

Red change bars indicate updates since January 2005 0.0

0.0

Confidential Draft February 2009 0.0

Manufacturer’s note : 0.0 Products that bear a CE mark fulfill the provisions of the Council Direc-tive 93/42/EEC of 14 June 1993 regarding medical equipment. 0.0

The CE mark applies exclusively to medical equipment and products that are released under the relevant EU guidelines mentioned above.0.0

The authors have taken care in the preparation of this book, but SIEMENS makes no expressed or limited warranty of any kind and assumes no responsi-bility for errors or omissions. No liability is assumed for incidental or consequen-tial damages in connection with or arising out of the use of the information or programs contained herein. SIEMENS reserves the right, in its sole discretion and without notice, to make substitutions and modifications in the products and practices described in this document. 0.0

Microsoft, Windows NT, Window, Internet Explorer and MS-DOS are trade-marks or registered trademarks of Microsoft Corporation. Clearcase and Atria are registered trademarks of Atria Software, Inc. Rational and the Rational Logo are trademarks or registered trademarks of Rational Software Corpora-tion. All other products are trademarks or registered trademarks of their respec-tive companies. 0.0

© Siemens AG 2001-2006 All Rights Reserved. 0.0

This document contains proprietary and confidential information which is prop-erty of SIEMENS AG, Medical Solutions, Erlangen, Germany, and is furnished for the sole purpose of the operation of a MAGNETOM product. No part of this documentation is to be used for any other purpose, and is not to be reproduced, copied, disclosed, transmitted, stored in a retrieval system or translated into any human or computer language, in any form, by any means, in whole or in part, without the prior and express consent of SIEMENS. 0.0

Except as may otherwise be explicitly agreed to in writing, SIEMENS makes no representation that equipment, software programs and practices described herein will not infringe on existing or future patent rights, copyrights, trade-marks, trade secrets or other proprietary rights of third parties. The descriptions contained herein do not imply the granting of licenses to make, use, sell, license or otherwise transfer SIEMENS products described herein. 0.0

IDEA is a tool limited to investigational use only. Because magnetic reso-nance image quality is fundamentally dependent on the timing and parameters of the acquisition sequence, the user must assure sufficient testing of clinical utility for any and all new sequences developed for use on humans. In addition, it is possible to inadvertently create and incorrectly label images with se-quences developed using IDEA. All labeling of images from investigational sequences must be verified by the user on phantoms before use on humans. Examinations performed using sequences generated with this package should be for investigational purposes only, and should not be used for diagnosis with-out corroborative examination using SIEMENS standard sequences. 0.0

0.0

Siemens AG, Medical Solutions, Magnetic Resonance Henkestraße 127, D-91052 Erlangen, Germany http://SiemensMedical.com 0.0

Headquarters in Berlin and Munich 0.0

Siemens AG, Wittelsbacher Platz 2, D-80333 München,Germany 0.0

0.0

http://SiemensMedical.com

A

syngo MR B17 –1Confidential Draft Feb 2009

0.0

Contents Installation Guide

Installation GuideA.1

General InformationGeneral Requirements ................................................... A.1–3

A.2Stand-alone InstallationInstallation of MS-DEV ................................................... A.2–3

Microsoft CD .............................................................. A.2–4Siemens MS-DEV CD ................................................ A.2–5

IDEA installation ............................................................. A.2–6

Additional packages ....................................................... A.2–7

A.3ClearCase InstallationIDEA installation ............................................................. A.3–3

Additional packages ....................................................... A.3–4

Changing the baseline .................................................... A.3–5

–2 IDEA ManualConfidential Draft Feb 2009

0.0

A.1

syngo MR B17 A.1–1Confidential Draft Feb 2009

0.0

General Information Installation Guide

General Information A.1

A.1–2 IDEA ManualConfidential Draft Feb 2009

0.0

Installation Guide General Requirements

General Requirements A.1

System requirementsA.1

The minimum hardware requirements for running IDEA are: A.1

Pentium 1 GHz

1024 MB RAM

The minimum software requirements for running IDEA are: A.1

Windows XP Service Pack 21

A HTML browser such as Netscape or Microsoft Internet Explorer (IE)

Microsoft Visual C++ 6.0, Enterprise Edition (with Service Pack 5).

For the installation, administrator rights are required on your system. A.1

The approximate disk space required for an installation is 1.6 GB. A.1

Working with IDEA requires additional space; the amount depends on thenumber of projects under development and the simulations being run. If anumber must be specified, 10 GB should be sufficient. These minimum sys-tem requirements should not be taken as a recommendation when consider-ing buying a new workstation. A.1

Network driver A.1

For internal communication between IDEA processes, AT command handlingis used. Therefore it is necessary that a network driver is installed and the net-work has been configured. This is also valid if your system is not connectedto a real network. A.1

C++ compilerA.1 Developing pulse sequences or applications within syngo-MR requires a C++compiler. This compiler is not included on the IDEA distribution DVD, but mustbe purchased separately. IDEA is validated with the A.1

Microsoft Visual C++ 6.0 Enterprise Edition (1998). A.1

On a stand-alone PC, the use of an edition or version of the MS C++ compilerother than this recommended one is at the customer’s risk. A.1

1. Windows XP Professional with Service Pack 2. No other Windows ver-sion is supported.


0.0


As this requested version can no longer be purchased from a Microsoftdealer, it can be ordered from Siemens. A.1

The MS-DEV should be installed before starting with the IDEA installationitself. For installation guidelines, please refer to the next chapters. A.1

A.1


0.0


A.1

Additional software A.1

There is some additional software on the IDEA distribution DVD: A.1

Microsoft Visual C++ Service Pack 5 Additionally, the Microsoft Visual C++ Service Pack 5 is required1. On theIDEA DVD, you can find it in the directory \Download\VS60SP5, but it canalso be obtained from the Microsoft service or for free by downloading itfrom the internet (www.microsoft.com/downloads). Please note that youmust not mix up different languages for the MS-DEV Studio and the MS-DEV Service Pack.

Info-ZIP compression utilityNOTE: IDEA is packaged on this DVD using Info-ZIP's compression utility.The installation program uses UnZip to read zip files from the DVD. Info-ZIP's software (Zip, UnZip and related utilities) is free and can be obtainedas source code or executables from various anonymous-ftp sites, includingftp.uu.net:/pub/archiving/zip/*.The complete, unmodified package can be found on the IDEA DVD in thefile \IDEA\install\ExternalPackages\Zip+Unzip.zip.

Cygnus GNU Unix toolThis software originaly comes from http://sources.redhat.com/cygwin/.

Tornado g++ cross compiler from x86 to MPCU(X86)This GNU compiler has been ported by Wind River Systems Inc. (http://www.windriver.com/index.html).

Note that this software is not part of the IDEA product and that it is not sold,but distributed for free. A.1

Baseline A.1 For every NUMARIS version, the matching IDEA version must be used. Forexample, for NUMARIS VA12A, use IDEA for VA12A; IDEA VA12B will notwork. Never try to mix different versions! A.1

Every NUMARIS package has a baseline label which identifies the build ofthis package, e.g. N4_VB13A_LATEST_20060408. It specifies both the soft-ware version and the date (in a yyyymmdd format). A.1

The baseline label of the IDEA package is printed on the distribution DVD. Itis also stored in the file DVD:\baseline_standalone.txt. A.1

1. Until version VA15A, service pack 3 had been requested.


0.0

http://sources.redhat.com/cygwin

http://www.windriver.com/index.html

http://www.windriver.com/index.html

ftp://ftp.uu.net/pub/archiving/zip

http://www.microsoft.com/downloads/details.aspx?FamilyID=e9411283-c8ad-4283-8d74-3d6efd917644&DisplayLang=en


The baseline label of the NUMARIS software on the scanner can be found outby Help → Info -> General

A.1

Caveat: A Numaris version sold under a marketing name (such as syngo MR2002B) can belong to different revisions (VA21A, VA21B, VA21C) and hencebelong to different baselines (N4_VA21A_LATEST_20020801,N4_VA21B_LATEST_20021003 etc.). These revisions are different baselinesand must not be mixed. A.1


0.0


A.1

Installation modes A.1

There are two different installation modes for IDEA: A.1

Stand-alone InstallationIDEA can be installed on any standard PC or Laptop. This offers the pos-sibility to develop applications without the need to sit in front of theNUMARIS console. This installation does not require syngo or NUMARISand needs about 1.6 GB of disk space.Details may be found on Page A.2–2.

Archive InstallationThis mode is reserved for SIEMENS in-house developers who haveaccess to the Clearcase archive. This mode sets only up the registry butdoes not install any files.Details may be found on Page A.3–2.

If the installation should be aborted by the user, it can be restarted or repeatedat any time without any problems. A.1

Update IDEA A.1 If there already exists an old IDEA installation with another baseline on yourstand-alone PC, it does not have to be uninstalled prior to the new installation,because the new multi_idea framework will take care of the different ver-sions. A.1

Unless the required version of the Microsoft Developer Studio or the Cygnustools is also subject to change, there is no need for the deinstallation and rein-stallation of this software package. A.1

After an IDEA update (i.e. a change of the baseline), it is necessary to recom-pile all your sequences. A.1

WARNING

The baseline labels of IDEA and the NUMARIS installation on the scanner must be identical! Different baselines must

never be mixed.

If you have different baselines on your scanner and your stand-alone IDEA, never take an application from your PC

to your scanner or vice versa.


0.0


Uninstall IDEAA.1 This is the way to uninstall IDEA: If any IDEA applications have been written,they should be saved in a directory outside of IDEA now. Your IDEA stuff isnot included in the save set created by the service backup! Start multi_ideaand enter the DELETE command. A.1

This will remove the complete IDEA subtree including all user-created sourcefiles. A.1

If you want to install a new version of IDEA directly afterwards, take care toupdate the environment variables prior to the installation, e.g. by calling theSystem Properties Environment window or by logging out. A.1


0.0

A.2


0.0

Stand-alone Installation Installation Guide

Stand-alone Installation A.2


0.0

Installation Guide Installation of MS-DEV

Installation of MS-DEV A.2

This chapter describes the installation of IDEA on a stand-alone standardWindowsXP personal computer. No Numaris software is required for thisinstallation. Sequences can be developed and the image reconstruction withraw data from the scanner can be simulated on the PC. A.2

The installation takes place in two parts: A.2

The installation of the Microsoft Developer Studio (MS-DEV & MS-DEVService Pack 5)

The installation of the Integrated Development Environment for Applica-tions (IDEA) itself

A.2

Note: Administrator rights are required (both for the C++ compiler installationand the IDEA installation itself). A.2

A.2

There are three substantial deviations from the default Microsoft installation:A.2

The root directory is C:\MSVStudio6.

The MFC template libraries must be installed.

The libraries for unicode support must be installed.

A.2

There are two different ways to install the Microsoft Developer Studio: A.2

a) You can use the MS-DEV CD ROM directly purchased by the customer.Then please follow the instructions in the next subsection "Microsoft CD"(Page A.2–4). A.2

b) You could also use the Siemens CD with a pre installed version. Pleasenote that this DVD must only be installed on one system according to thelicensing terms. If you have this CD, please go to the subsection "SiemensCD" (Page A.2–5). A.2

A.2


0.0


Microsoft CD A.2

A.2

(1) Login as a user with full administrator rights, such as "administrator".

(2) Insert CD-ROM and install VC 6.0 ++ by running CD:\Setup.exe.Accept the default values, but change the following points:Target directory: C:\MSVStudio6\Common

Installation type: CustomOptions:Select ‘VC++ MFC and Template Libraries’ and press Change Option.Select ‘MS Foundation Class Libraries’ and press Change Option.Select additionally "Static Libraries for Unicode" and "Shared Libraries forUnicode".2x OK.Continue.Check the ‘Register Environment Variables’ box.OK (installation starts).

(3) Remove installation CD from drive and boot computer.

(4) Login as a user with full administrator rights, such as “administrator”Note: If any error message pop-up window appears, confirm this mes-sage and proceed.

(5) Insert the Service Pack – CD (If you have installed an English MS-DEVversion, you can find the Service Pack on the IDEA CD in the directory"\Download\VS60SP5"): run file SetupSP5.exe(To find the file on CD, use the ‘Find’ function of the Windows Explorer inthe menu Tools -> Find -> File or Folders).

(6) Remove CD from drive and reboot.

NOTE

Do not accept the default target directory proposed by Microsoft, but use “C:\MSVStudio6\Common”. Otherwise

the makefiles will not work properly.


0.0

Installation Guide Installation of MS-DEV

Siemens MS-DEV CD A.2

This installation step will take about 5 min. A.2

A.2

(1) Login as "administrator".

(2) Insert Siemens CD-ROM and install VC 6.0 ++ by running"R:\Installation_Visual_Studio6.bat". Wait until the installation is com-pleted. Do not reboot.

(3) Remove MS-DEV installation CD from drive, insert Siemens ServicePack CD and run the file CD:\Installation_SP5.bat.

(4) When the following window pops up, click the "OK" button:

(5) When the following window pops up, click the "OK" button:

(6) Remove CD from drive and reboot.

A.2

A.2

A.2


0.0


IDEA installation A.2

Prerequisites: A.2

MS Visual C++ must have been installed.

A.2

(1) Login under your usual login name (you must have administrator rights).

(2) Insert the IDEA DVD

(3) Start a DOS command window and change to the DVD drive.

(4) Type "ideainstall.bat" and follow the instructions in the window.

Note: If there is not enough disk space on drive C: IDEA can be installedon any other drive (e.g., drive D:). You will be asked to specify the driveletter during the installation dialog.

Note: IDEA requires a drive letter to be assigned to the IDEA root direc-tory. The first unsigned drive letter is automatically selected from thealphabet starting from Z.

(5) To check the results of the installation, go to Start → IDEA → multi_idea.Select the drive letter of the desired baseline and type "sde", the SDEshell should start.


0.0

Installation Guide Additional packages

Additional packages A.2

It is recommended to install some more software tools on your system. Forlegal reasons, they cannot be distributed on the IDEA DVD, but they can bedownloaded from the web for free: A.2

DICOM viewer. A list of free viewers can be obtained from http://www.psy-ology.nottingham.ac.uk/staff/cr1/dicom.html.


0.0

http://www.psychology.nottingham.ac.uk/staff/cr1/dicom.html#links




0.0

A.3


0.0

ClearCase Installation Installation Guide

ClearCase Installation A.3

This installation mode is only suitable for SIEMENS internal software devel-opers who can access the N4 ClearCase archive. A.3

A.3

Prerequisites: A.3

ClearCase and MS Visual C++ must have been installed as recommendedby your system administrator.

A.3


0.0

Installation Guide IDEA installation

IDEA installation A.3

A.3

(1) Login under your usual ClearCase login name

(2) Select the desired base line.

(3) Start a command window and run “\n4\pkg\MrApplica-tions\MrIDEA\install\bin\ideainstall.cmd” in your view.

(4) It is not necessary to boot the system.☺To check the results of the installation, go to Start → IDEA → multi_idea.Select the drive letter of the desired baseline and type "sde", the SDEshell should start.

(5) It is left to the user to create any additional shortcuts in the Start Menu.


0.0


Additional packages A.3

It is recommended to install some more tools on your system. For legal rea-sons, they cannot be distributed on the IDEA CD, but they can be downloadedfrom the web for free: A.3

DICOM viewer. A list of free viewers can be obtained from http://www.psy-chology.nottingham.ac.uk/staff/cr1/dicom.html.

A.3


0.0



Installation Guide Changing the baseline

Changing the baseline A.3

If you want to change your current baseline, two steps are necessary: A.3

(1) Change your ClearCase config spec, e.g. with the "cleartool edcs"command.

(2) Run the initprod command to initialize your /prod VOB and to updateyour virtual MAGNETOM configurations.


0.0



0.0

Documents

Insal manual singo MR VB17.pdf